Search Results

Search found 89612 results on 3585 pages for 'sof user'.

Page 2413/3585 | < Previous Page | 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420  | Next Page >

• COPSSH RSA only authentication connection problem

  - by Siriss

  Hello all- I am trying to setup an RSA Authentication only SSH/SFTP server. The SSH will be used primarily for RDC. Everything works just fine if I use password authentication. I am using Putty Key Generator to create he keys and I have pasted the key into authorized_keys file and restarted the OpenSSH server. I am using FileZilla to test the SFTP connection as that is the most important. For my tests I have created the keys without password correction. It will not work with a standard SSH connection either. It says "Server refused our key". I have recreated the key twice double checking with a guide on google, and I am pretty sure I did it correctly. I load the key file into FileZilla under settings/SFTP and try to connect and I get the following error: Disconnected: No supported authentication methods available. I have been playing with the different settings all night and I cannot figure it out. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.80 2008/07/02 02:24:18 djm Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # Disable legacy (protocol version 1) support in the server for new # installations. In future the default will change to require explicit # activation of protocol 1 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 1024 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH #LogLevel INFO # Authentication: #LoginGraceTime 2m PermitRootLogin no #StrictModes yes #MaxAuthTries 6 #MaxSessions 10 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! PasswordAuthentication no PermitEmptyPasswords no # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. UsePAM no #AllowAgentForwarding yes #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner none # override default of no subsystems Subsystem sftp /bin/sftp-server # Example of overriding settings on a per-user basis #Match User anoncvs # X11Forwarding no # AllowTcpForwarding no # ForceCommand cvs server Thank you so much for your help!

  Read the article

• virtual host setup: can't access wordpress site without www

  - by two7s_clash

  I would like to access my site both with and without using the www. Currently it only works with. Leaving out the www just goes to a blank page. Also, wp-admin just loads a blank page too. I have set an A record for mysite.com and www.mysite.com, both pointing to my static Bitnami IP. I also have a subdomain mapped to another directory that is working just fine (conference.mysite.com and www.conference.mysite.com). I'm using a Bitnami stack on an AWS EC2 micro instance. Here is my httpd.conf: ServerRoot "/opt/bitnami/apache2" Listen 80 LoadModule authn_file_module modules/mod_authn_file.so blah blah blah.... LoadModule php5_module modules/libphp5.so <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> User daemon Group daemon </IfModule> </IfModule> ServerAdmin [email protected] ServerName localhost:80 DocumentRoot "/opt/bitnami/apps/wordpress1/htdocs/" <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Allow from all </Directory> <Directory "/opt/bitnami/apps/wordpress1/htdocs/"> Options Indexes MultiViews +FollowSymLinks LanguagePriority en AllowOverride All Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.html index.php </IfModule> <FilesMatch "^\\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "logs/error_log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \\"%r\\" %>s %b \\"%{Referer}i\\" \\"%{User-Agent}i\\"" combined LogFormat "%h %l %u %t \\"%r\\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \\"%r\\" %>s %b \\"%{Referer}i\\" \\"%{User-Agent}i\\" %I %O" combinedio </IfModule> CustomLog "logs/access_log" common </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "/opt/bitnami/apache2/cgi-bin/" </IfModule> <Directory "/opt/bitnami/apache2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz </IfModule> Include conf/extra/httpd-mpm.conf <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> AddType application/x-httpd-php .php .phtml LoadModule wsgi_module modules/mod_wsgi.so WSGIPythonHome /opt/bitnami/python ServerSignature Off ServerTokens Prod AddType application/x-httpd-php .php PHPIniDir "/opt/bitnami/php/etc" Include "/opt/bitnami/apps/phpmyadmin/conf/phpmyadmin.conf" ExtendedStatus On <Location /server-status> SetHandler server-status Order Deny,Allow Deny from all Allow from localhost </Location> Include "/opt/bitnami/apache2/conf/bitnami/httpd.conf" Include "/opt/bitnami/apps/virtualhost.conf" Here is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin xx DocumentRoot "/opt/bitnami/apps/wordpress1/htdocs" ServerName mbird.com ServerAlias www.mbird.com ErrorLog "logs/wordpress-error_log" CustomLog "logs/wordpress-access_log" common </VirtualHost> <Directory "/opt/bitnami/apps/wordpress1/htdocs"> Options Indexes MultiViews +FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ### WordPress conference.mbird.com configuration ### <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "/opt/bitnami/apps/wordpress/htdocs" ServerName conference.mbird.com ServerAlias www.conference.mbird.com ErrorLog "logs/confwordpress-error_log" CustomLog "logs/confwordpress-access_log" common </VirtualHost> <Directory "/opt/bitnami/apps/wordpress/htdocs"> Options Indexes MultiViews +FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ###

  Read the article

• Centos 7. Freeradius fails to start on boot

  - by Alex

  I was messing around with FreeRADIUS and MySQL (MariaDB) and it seems FreeRADIUS service can't start properly on startup. But it starts fine using root user or in debug mode (radiusd -X) and works just fine! Debug mode shows no errors. systemctl command shows that radiusd.service has failed to start. /var/log/messages output: Aug 21 15:52:29 nexus-test systemd: Starting The Apache HTTP Server... Aug 21 15:52:29 nexus-test systemd: Starting MariaDB database server... Aug 21 15:52:29 nexus-test systemd: Starting FreeRADIUS high performance RADIUS server.... Aug 21 15:52:29 nexus-test systemd: Started OpenSSH server daemon. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Logging to '/var/log/mariadb/mariadb.log'. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql Aug 21 15:52:30 nexus-test systemd: Started Postfix Mail Transport Agent. Aug 21 15:52:30 nexus-test avahi-daemon[604]: Registering new address record for fe80::250:56ff:fe85:e4af on eth0.*. Aug 21 15:52:30 nexus-test systemd: radiusd.service: control process exited, code=exited status=1 Aug 21 15:52:30 nexus-test systemd: Failed to start FreeRADIUS high performance RADIUS server.. Aug 21 15:52:30 nexus-test systemd: Unit radiusd.service entered failed state. Aug 21 15:52:31 nexus-test kdumpctl: kexec: loaded kdump kernel Aug 21 15:52:31 nexus-test kdumpctl: Starting kdump: [OK] Aug 21 15:52:31 nexus-test systemd: Started Crash recovery kernel arming. Aug 21 15:52:31 nexus-test systemd: Started The Apache HTTP Server. Aug 21 15:52:31 nexus-test systemd: Started MariaDB database server. /var/log/radius/radius.log output: Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Driver rlm_sql_mysql (module rlm_sql_mysql) loaded and linked Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Attempting to connect to database "radius" Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Opening additional connection (0) Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Couldn't connect socket to MySQL server radius@localhost:radius Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Mysql error 'Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock' (2)' Thu Aug 21 15:24:16 2014 : Error: rlm_sql (sql): Opening connection failed (0) Thu Aug 21 15:24:16 2014 : Error: /etc/raddb/mods-enabled/sql[47]: Instantiation failed for module "sql" After seeing this I tried to replicate the problem, killed mariadb.service and started to run debug mode again. And it spits out the same problem as in the radius.log. I tried disabling iptables and firewalld and rebooting, but no luck: systemctl disable iptables systemctl disable firewalld So maybe the problem is in the process startup order or delay of some kind. Maybe FreeRADIUS's SQL module can't connect to not yet started MariaDB? If it, how can I fix this? In earlier versions of RHEL/CENTOS I know you easily see service start order in like rc.d or stuff, now IDK. I am new to this fancy "systemd", "systemctl", "firewalld" stuff Centos 7 introduced so sorry I'm a little bit confused. Also this new FreeRADIUS 3 structure... PS. MariaDB is enabled on startup, credentials in FR DB configuration are correct A little update: cat /etc/systemd/system/multi-user.target.wants/radiusd.service output: [Unit] Description=FreeRADIUS high performance RADIUS server. After=syslog.target network.target [Service] Type=forking PIDFile=/var/run/radiusd/radiusd.pid ExecStartPre=-/bin/chown -R radiusd.radiusd /var/run/radiusd ExecStartPre=/usr/sbin/radiusd -C ExecStart=/usr/sbin/radiusd -d /etc/raddb ExecReload=/usr/sbin/radiusd -C ExecReload=/bin/kill -HUP $MAINPID [Install] WantedBy=multi-user.target

  Read the article

• How to resolve high CPU + excessive stat("/etc/localtime") and clock_gettime(CLOCK_REALTIME) calls

  - by Yemster

  I've been experiencing really high CPU on a ruby on rails app (see stack below) and have been trying to diagnose the possible causes to no avail. Stack: ruby 1.9.3 rails 3.2.6 Apache/2.2.21 (Debian) Phusion Passenger 3.0.11 Whenever I run strace against the spiking Rack process PID (see Top excerpt below), I am seeing a tonne of stat("/etc/localtime") and clock_gettime(CLOCK_REALTIME) calls and have no idea how to stop these. Excerpt from Top showin running PID: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 11674 www-user 20 0 313m 182m 5076 R 99 2.3 63:04.60 Rack: /var/www/my_rails_app/current 11634 www-user 20 0 411m 216m 5144 S 10 2.7 197:55.63 Rack: /var/www/my_rails_app/current Strace snippet below: [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 141474018}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 141577456}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 143073982}) = 0 [pid 11674] poll([{fd=15, events=POLLIN|POLLPRI}], 1, 0) = 0 (Timeout) [pid 11674] write(15, "b\0\0\0\3SELECT `images`.* FROM `ima"..., 102) = 102 [pid 11674] read(15, "\1\0\0\1\0229\0\0\2\3def\23myappy_productio"..., 16384) = 2063 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 144138035}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 ... [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] stat("/etc/localtime", {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 154076443}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 154189429}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 157185700}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 157298770}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 165076003}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 165212572}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 167542679}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354058955, 167683436}) = 0 .... [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 62052248}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 62182486}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 62919948}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 63057266}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 63751707}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 73730686}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 75874687}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 76077133}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 78205019}) = 0 ... [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 89370879}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 89583247}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 91637614}) = 0 [pid 11674] clock_gettime(CLOCK_REALTIME, {1354060036, 91782149}) = 0 Have Google'd around and came across a number of suggestions which I've tried with no success. Things tried so far: Have tried setting time zone as recommended here Made no difference and issue still persists. Content of my /etc/localtime: TZif2UTCTZif2UTC UTC0 Have tried the recommended fix for the leapsecond bug: date -s 'date' No joy so far. I'm fresh out of ideas so any help/advice on how to diagnose or resolve would be greatly appreciated.

  Read the article

• /usr/bin/sshd isn't linked against PAM on one of my systems. What is wrong and how can I fix it?

  - by marc.riera

  Hi, I'm using AD as my user account server with ldap. Most of the servers run with UsePam yes except this one, it has lack of pam support on sshd. root@linserv9:~# ldd /usr/sbin/sshd linux-vdso.so.1 => (0x00007fff621fe000) libutil.so.1 => /lib/libutil.so.1 (0x00007fd759d0b000) libz.so.1 => /usr/lib/libz.so.1 (0x00007fd759af4000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007fd7598db000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007fd75955b000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x00007fd759323000) libc.so.6 => /lib/libc.so.6 (0x00007fd758fc1000) libdl.so.2 => /lib/libdl.so.2 (0x00007fd758dbd000) /lib64/ld-linux-x86-64.so.2 (0x00007fd759f0e000) I have this packages installed root@linserv9:~# dpkg -l|grep -E 'pam|ssh' ii denyhosts 2.6-2.1 an utility to help sys admins thwart ssh hac ii libpam-modules 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules for PAM ii libpam-runtime 0.99.7.1-5ubuntu6.1 Runtime support for the PAM library ii libpam-ssh 1.91.0-9.2 enable SSO behavior for ssh and pam ii libpam0g 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules library ii libpam0g-dev 0.99.7.1-5ubuntu6.1 Development files for PAM ii openssh-blacklist 0.1-1ubuntu0.8.04.1 list of blacklisted OpenSSH RSA and DSA keys ii openssh-client 1:4.7p1-8ubuntu1.2 secure shell client, an rlogin/rsh/rcp repla ii openssh-server 1:4.7p1-8ubuntu1.2 secure shell server, an rshd replacement ii quest-openssh 5.2p1_q13-1 Secure shell root@linserv9:~# What I'm doing wrong? thanks. Edit: root@linserv9:~# cat /etc/pam.d/sshd # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password Edit2: UsePAM yes fails With this configuration ssh fails to start : root@linserv9:/home/admmarc# cat /etc/ssh/sshd_config |grep -vE "^[ \t]*$|^#" Port 22 Protocol 2 ListenAddress 0.0.0.0 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys ChallengeResponseAuthentication yes UsePAM yes Subsystem sftp /usr/lib/sftp-server root@linserv9:/home/admmarc# The error it gives is as follows root@linserv9:/home/admmarc# /etc/init.d/ssh start * Starting OpenBSD Secure Shell server sshd /etc/ssh/sshd_config: line 75: Bad configuration option: UsePAM /etc/ssh/sshd_config: terminating, 1 bad configuration options ...fail! root@linserv9:/home/admmarc#

  Read the article

• Email forwarding from my domain to gmail - FAIL

  - by pitosalas

  [There are numerous similar questions on ServerFault but I couldn't find one that was exactly on point] Background: I use Gmail for my email client. My email is [email protected]. However the email that people communicate to me with is [email protected]. I run the server that hosts www.example.com and other domains, at ServerBeach. Up to yesterday, I had SENDMAIL painlessly just forward emails to [email protected] to [email protected] and everything was fine, for several years in fact. Suddenly my email stopped working - that is, my gmail account stopped receiving emails via the forward from my server. Looking into it I found a bunch of emails sitting on my server with content like this: ... while talking to gmail-smtp-in.l.google.com.: RCPT To: <<< 450-4.2.1 The user you are trying to contact is receiving mail at a rate that <<< 450-4.2.1 prevents additional messages from being delivered. Please resend your <<< 450-4.2.1 message at a later time. If the user is able to receive mail at that <<< 450-4.2.1 time, your message will be delivered. For more information, please <<< 450 4.2.1 visit xxxxxx://mail.google.com/support/bin/answer.py?answer=6592 u15si37138086qco.76 [email protected]... Deferred: 450-4.2.1 The user you are trying to contact is receiving mail at a rate that DATA <<< 550-5.7.1 [64.34.168.137 1] Our system has detected an unusual rate of <<< 550-5.7.1 unsolicited mail originating from your IP address. To protect our <<< 550-5.7.1 users from spam, mail sent from your IP address has been blocked. <<< 550-5.7.1 Please visit xxxxx://www.google.com/mail/help/bulk_mail.html to review <<< 550 5.7.1 our Bulk Email Senders Guidelines. u15si37138086qco.76 554 5.0.0 Service unavailable ... while talking to alt1.gmail-smtp-in.l.google.com.: From what I've been researching, I think somehow someone has/is hijacking my domain name or something and this somehow has caused gmail's servers to notice and cut me off. But I don't know really what's going on nor do I see whatever emails might be involved. I've read stuff on zoneedit.com that sounds like they might have a solution in their service for what I am trying to do. I also read a lot about admining DNS and SENDMAIL and tried various things, but nothing works. Can you tell from my description what is going on that caused GMail's server to stop accepting email from my server and is there a way to stop it? What is the 'correct' way to configure things so that emails to [email protected] behave as if they were sent to [email protected]? Thanks so much!

  Read the article

• Debian virtual memory reaching limit

  - by Gregor

  As a relative newbie to systems, I inherited a Debian server and I've noticed that virtual memory is very high (around 95%!). The server has been running slow for around 6 months, and I was wondering if any of you had any tips on things I could try, particularly on freeing up memory. The server hosts various websites and also a Postit email server. Here are the details: Operating system Debian Linux 5.0 Webmin version 1.580 Time on system Thu Apr 12 11:12:21 2012 Kernel and CPU Linux 2.6.18-6-amd64 on x86_64 Processor information Intel(R) Core(TM)2 Duo CPU E7400 @ 2.80GHz, 2 cores System uptime 229 days, 12 hours, 50 minutes Running processes 138 CPU load averages 0.10 (1 min) 0.28 (5 mins) 0.36 (15 mins) CPU usage 14% user, 1% kernel, 0% IO, 85% idle Real memory 2.94 GB total, 1.69 GB used Virtual memory 3.93 GB total, 3.84 GB used Local disk space 142.84 GB total, 116.13 GB used Free m output: free -m total used free shared buffers cached Mem: 3010 2517 492 0 107 996 -/+ buffers/cache: 1413 1596 Swap: 4024 3930 93 Top output: top - 11:59:57 up 229 days, 13:38, 1 user, load average: 0.26, 0.24, 0.26 Tasks: 136 total, 2 running, 134 sleeping, 0 stopped, 0 zombie Cpu(s): 3.8%us, 0.5%sy, 0.0%ni, 95.0%id, 0.7%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3082544k total, 2773160k used, 309384k free, 111496k buffers Swap: 4120632k total, 4024712k used, 95920k free, 1036136k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 28796 www-data 16 0 304m 68m 6188 S 8 2.3 0:03.13 apache2 1 root 15 0 10304 592 564 S 0 0.0 0:00.76 init 2 root RT 0 0 0 0 S 0 0.0 0:04.06 migration/0 3 root 34 19 0 0 0 S 0 0.0 0:05.67 ksoftirqd/0 4 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 5 root RT 0 0 0 0 S 0 0.0 0:00.06 migration/1 6 root 34 19 0 0 0 S 0 0.0 0:01.26 ksoftirqd/1 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/1 8 root 10 -5 0 0 0 S 0 0.0 0:00.12 events/0 9 root 10 -5 0 0 0 S 0 0.0 0:00.00 events/1 10 root 10 -5 0 0 0 S 0 0.0 0:00.00 khelper 11 root 10 -5 0 0 0 S 0 0.0 0:00.02 kthread 16 root 10 -5 0 0 0 S 0 0.0 0:15.51 kblockd/0 17 root 10 -5 0 0 0 S 0 0.0 0:01.32 kblockd/1 18 root 15 -5 0 0 0 S 0 0.0 0:00.00 kacpid 127 root 10 -5 0 0 0 S 0 0.0 0:00.00 khubd 129 root 10 -5 0 0 0 S 0 0.0 0:00.00 kseriod 180 root 10 -5 0 0 0 S 0 0.0 70:09.05 kswapd0 181 root 17 -5 0 0 0 S 0 0.0 0:00.00 aio/0 182 root 17 -5 0 0 0 S 0 0.0 0:00.00 aio/1 780 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata/0 782 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata/1 783 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata_aux 802 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_0 803 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_1 804 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_2 805 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_3 1013 root 10 -5 0 0 0 S 0 0.0 49:27.78 kjournald 1181 root 15 -4 16912 452 448 S 0 0.0 0:00.05 udevd 1544 root 14 -5 0 0 0 S 0 0.0 0:00.00 kpsmoused 1706 root 13 -5 0 0 0 S 0 0.0 0:00.00 kmirrord 1995 root 18 0 193m 3324 1688 S 0 0.1 8:52.77 rsyslogd 2031 root 15 0 48856 732 608 S 0 0.0 0:01.86 sshd 2071 root 25 0 17316 1072 1068 S 0 0.0 0:00.00 mysqld_safe 2108 mysql 15 0 320m 72m 4368 S 0 2.4 1923:25 mysqld 2109 root 18 0 3776 500 496 S 0 0.0 0:00.00 logger 2180 postgres 15 0 99504 3016 2880 S 0 0.1 1:24.15 postgres 2184 postgres 15 0 99504 3596 3420 S 0 0.1 0:02.08 postgres 2185 postgres 15 0 99504 696 628 S 0 0.0 0:00.65 postgres 2186 postgres 15 0 99640 892 648 S 0 0.0 0:01.18 postgres

  Read the article

• what is best config for nginx worker_rlimit_nofile and worker_connections 28672

  - by Binh Nguyen

  i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

  Read the article

• Squid - Logging to MySQL without empty rows/skipped records?

  - by Lee Ward

  I'm trying to figure out how to make Squid proxy log to MySQL. I know ACL order is pretty important but I'm not sure if I understand exactly what ACLs are or do, it's difficult to explain, but hopefully you'll see where I'm going with this as you read! I have created the lines to make Squid interact with a helper in squid.conf as follows: external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log The external ACL helper (mysql_lg.php) is a PHP script and is as follows: error_reporting(0); if (! defined(STDIN)) { define("STDIN", fopen("php://stdin", "r")); } $res = mysql_connect('localhost', 'squid', 'testsquidpw'); $dbres = mysql_select_db('squid', $res); while (!feof(STDIN)) { $line = trim(fgets(STDIN)); $fields = explode(' ', $line); $user = rawurldecode($fields[0]); $cli_ip = rawurldecode($fields[1]); $protocol = rawurldecode($fields[2]); $uri = rawurldecode($fields[3]); $q = "INSERT INTO logs (id, user, cli_ip, protocol, url) VALUES ('', '".$user."', '".$cli_ip."', '".$protocol."', '".$uri."');"; mysql_query($q) or die (mysql_error()); if ($fault) { fwrite(STDOUT, "ERR\n"); }; fwrite(STDOUT, "OK\n"); } The configuration I have right now looks like this: ## Authentication Handler auth_param ntlm program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 30 auth_param negotiate program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-basic auth_param negotiate children 5 # Allow squid to update log external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log acl localnet src 172.16.45.0/24 acl AuthorizedUsers proxy_auth REQUIRED acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl CONNECT method CONNECT acl blockeddomain url_regex "/etc/squid3/bl.acl" http_access deny blockeddomain deny_info ERR_BAD_GENERAL blockeddomain # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # Allow the internal network access to this proxy http_access allow localnet # Allow authorized users access to this proxy http_access allow AuthorizedUsers # FINAL RULE - Deny all other access to this proxy http_access deny all From testing, the closer to the bottom I place the logging lines the less it logs. Oftentimes, it even places empty rows in to the MySQL table. The file-based logs in /var/log/squid3/access.log are correct but many of the rows in the access logs are missing from the MySQL logs. I can't help but think it's down to the order I'm putting lines in because I want to log everything to MySQL, unauthenticated requests, blocked requests, which category blocked a specific request. The reason I want this in MySQL is because I'm trying to have everything managed via a custom web-based frontend and want to avoid using any shell commands and access to system log files if I can help it. The end result is to make it as easy as possible to maintain without keeping staff waiting on the phone whilst I add a new rule and reload the server! Hopefully someone can help me out here because this is very much a learning experience for me and I'm pretty stumped. Many thanks in advance for any help!

  Read the article

• x11vnc working in Ubuntu 10.10

  - by pablorc

  I'm trying to start x11vnc in a Ubuntu 10.10 (my server is in Amazon EC2), but I have the next error $ sudo x11vnc -forever -usepw -httpdir /usr/share/vnc-java/ -httpport 5900 -auth /usr/sbin/gdm 25/11/2010 13:29:51 passing arg to libvncserver: -httpport 25/11/2010 13:29:51 passing arg to libvncserver: 5900 25/11/2010 13:29:51 -usepw: found /home/ubuntu/.vnc/passwd 25/11/2010 13:29:51 x11vnc version: 0.9.10 lastmod: 2010-04-28 pid: 3504 25/11/2010 13:29:51 XOpenDisplay(":0.0") failed. 25/11/2010 13:29:51 Trying again with XAUTHLOCALHOSTNAME=localhost ... 25/11/2010 13:29:51 *************************************** 25/11/2010 13:29:51 *** XOpenDisplay failed (:0.0) *** x11vnc was unable to open the X DISPLAY: ":0.0", it cannot continue. *** There may be "Xlib:" error messages above with details about the failure. Some tips and guidelines: ** An X server (the one you wish to view) must be running before x11vnc is started: x11vnc does not start the X server. (however, see the -create option if that is what you really want). ** You must use -display <disp>, -OR- set and export your $DISPLAY environment variable to refer to the display of the desired X server. - Usually the display is simply ":0" (in fact x11vnc uses this if you forget to specify it), but in some multi-user situations it could be ":1", ":2", or even ":137". Ask your administrator or a guru if you are having difficulty determining what your X DISPLAY is. ** Next, you need to have sufficient permissions (Xauthority) to connect to the X DISPLAY. Here are some Tips: - Often, you just need to run x11vnc as the user logged into the X session. So make sure to be that user when you type x11vnc. - Being root is usually not enough because the incorrect MIT-MAGIC-COOKIE file may be accessed. The cookie file contains the secret key that allows x11vnc to connect to the desired X DISPLAY. - You can explicitly indicate which MIT-MAGIC-COOKIE file should be used by the -auth option, e.g.: x11vnc -auth /home/someuser/.Xauthority -display :0 x11vnc -auth /tmp/.gdmzndVlR -display :0 you must have read permission for the auth file. See also '-auth guess' and '-findauth' discussed below. ** If NO ONE is logged into an X session yet, but there is a greeter login program like "gdm", "kdm", "xdm", or "dtlogin" running, you will need to find and use the raw display manager MIT-MAGIC-COOKIE file. Some examples for various display managers: gdm: -auth /var/gdm/:0.Xauth -auth /var/lib/gdm/:0.Xauth kdm: -auth /var/lib/kdm/A:0-crWk72 -auth /var/run/xauth/A:0-crWk72 xdm: -auth /var/lib/xdm/authdir/authfiles/A:0-XQvaJk dtlogin: -auth /var/dt/A:0-UgaaXa Sometimes the command "ps wwwwaux | grep auth" can reveal the file location. Starting with x11vnc 0.9.9 you can have it try to guess by using: -auth guess (see also the x11vnc -findauth option.) Only root will have read permission for the file, and so x11vnc must be run as root (or copy it). The random characters in the filenames will of course change and the directory the cookie file resides in is system dependent. See also: http://www.karlrunge.com/x11vnc/faq.html I've already tried with some -auth options but the error persist. I have gdm running. Thank you in advance

  Read the article

• "Service Unavailable" when browsing to static HTML page in non-application IIS website on Windows 2003 (possibly SharePoint WSS 2.0 related?)

  - by Jordan Rieger

  Background: My client has an old Pentium III Windows 2003 server whose 16/36 GB disks are dying. On it he has a database-driven web site and email application that needs further customization by a developer (me). First we need to get it working on the new server. The original developer is no longer available to provide a system setup guide. So my client got a tech who imaged the old drives over to the new server and managed to get it booting. But the IIS-driven site no longer works. In fact it seems that IIS itself does not work. Problem: Service Unavailable when attempting to browse from the server itself to the URL for a local Web Site called test which I setup in IIS to serve a single static index.htm file. This I did to isolate the problem, and eliminate the client's application from the equation. The site is setup on port 80 with the host header "test.myclientsdomain.com", and I used the etc\hosts file to point that host at the local IP. I know the host entry took effect because I can ping it. When doing an iisreset, I get: Attempting start... Restart attempt failed. IIS Admin Service or a service dependent on IIS Admin is not active. It most likely failed to start, which may mean that it's disabled. Despite this message, the services all stay in the Started state. The only relevant System event logs I found are: Event Type: Error Event Source: W3SVC Event Category: None Event ID: 1002 Date: 11/4/2012 Time: 11:04:47 PM User: N/A Computer: ALPHA1 Description: Application pool 'DefaultAppPool' is being automatically disabled due to a series of failures in the process(es) serving that application pool. Event Type: Error Event Source: W3SVC Event Category: None Event ID: 1039 Date: 11/4/2012 Time: 11:13:12 PM User: N/A Computer: ALPHA1 Description: A process serving application pool 'DefaultAppPool' reported a failure. The process id was '5636'. The data field contains the error number. Data: 0000: 7e 00 07 80 ~.. And one Application event log: Event Type: Error Event Source: Windows SharePoint Services 2.0 Event Category: None Event ID: 1000 Date: 11/4/2012 Time: 11:34:04 PM User: N/A Computer: ALPHA1 Description: #50070: Unable to connect to the database STS_Config on ALPHA2\SharePoint. Check the database connection information and make sure that the database server is running. That last log tells me that the tech may have initially tried to have both the old and the new server running, by renaming the new server from ALPHA1 to ALPHA2. And perhaps SharePoint grabbed onto that change, and now can't tell that the machine name has been switched back to the old ALPHA1. But why would SharePoint interfere with a static IIS web site serving a single HTML file? The test site is not even within an Application pool (I clicked the Remove button.) What I have tried/eliminated: No relevant services seem to be disabled: IIS Admin, WWW Publishing, Sharepoint Timer Giving Full Control to All Users/Everyone on the c:\inetpub\test folder serving my test site. I can connect to and query the local SharePoint config database (ALPHA1\SHAREPOINT\STS_CONFIG) from SSMS. But when I try to do stsadm -o setconfigdb -connect -databaseserver ALPHA1\SHAREPOINT it tells me The SharePoint admininstration port does not exist. Please use stsadm.exe to create it. And when I do that, using the port 9487 specified in the IIS SharePoint Admin site config, it tells me the port is already in use. Needless to say, simply browsing to the admin site gives me a similar error about being unable to reach the config database. I didn't want to go further down the SharePoint path as it may be completed unrelated to my IIS issue, and I don't even know yet if SharePoint is required for this application to work. The app itself is ASP.Net/C#/Silverlight and a little MS Word integration (maybe that's where the SharePoint stuff comes in.)

  Read the article

• Optimise Apache for EC2 micro instance

  - by Shiyu Sekam

  I'm running apache2 on a EC2 micro instance with ~600 mb RAM. The instance was running for almost a year without problems, but in the last weeks it just keeps crashing, because the server reached MaxClients. The server basically runs few websites, one wordpress blog(not often used), company website(most used) and 2 small sites, which are just internal. The database for the blog runs on RDS, so there's no Mysql running on this web server. When I came to the company, the server already was setup and is running apache + mod_php + prefork. We want to migrate that in the future to a nginx + php-fpm, but it still needs further testing. So for now I have to stick with the old setup. I also use CloudFlare DDOS protection in front of the server, because it was attacked a couple of the times in the last weeks. My company don't want to pay money for a better web server at this point, so I have to stick with the micro instance also. Additionally the code for the website we run is really bad and slow and sometimes a single page load can take up to 15 seconds. The whole website is dynamic and written in PHP, so caching isn't really an option here. It's a customized search for users. I've already turned off KeepAlive, which improved the performance a little bit. My prefork config looks like the following: StartServers 2 MinSpareServers 2 MaxSpareServers 5 ServerLimit 10 MaxClients 10 MaxRequestsPerChild 100 The server just becomes unresponsive after a while running and I've run the following command to see how many connections there are: netstat | grep http | wc -l 75 Trying to restart apache helps for a short moment, but after that a while the apache process(es) become unresponsive again. I've the following modules enabled(output of apache2ctl -M) Loaded Modules: core_module (static) log_config_module (static) logio_module (static) version_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) authz_host_module (shared) deflate_module (shared) dir_module (shared) expires_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) setenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK apache2.conf # Security ServerTokens OS ServerSignature On TraceEnable On ServerName "web.example.com" ServerRoot "/etc/apache2" PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive off User www-data Group www-data AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> <Directory /> Options FollowSymLinks AllowOverride None </Directory> DefaultType none HostnameLookups Off ErrorLog /var/log/apache2/error.log LogLevel warn EnableSendfile On #Listen 80 Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf Include /etc/apache2/ports.conf LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include /etc/apache2/conf.d/*.conf Include /etc/apache2/sites-enabled/*.conf Vhost of main site <VirtualHost *:80> ServerName www.example.com ## Vhost docroot DocumentRoot /srv/www/jenkins/Web ## Directories, there should at least be a declaration for /srv/www/jenkins/Web <Directory /srv/www/jenkins/Web> AllowOverride All Order allow,deny Allow from all </Directory> ## Load additional static includes ## Logging ErrorLog /var/log/apache2/www.example.com.error.log LogLevel warn ServerSignature Off CustomLog /var/log/apache2/www.example.com.access.log combined ## Rewrite rules RewriteEngine On RewriteCond %{HTTP_HOST} !^www.example.com$ RewriteRule ^.*$ http://www.example.com%{REQUEST_URI} [R=301,L] ## Server aliases ServerAlias www.example.invalid ServerAlias example.com ## Custom fragment <Location /srv/www/jenkins/Web/library> Order Deny,Allow Deny from all </Location> <Files ~ "^\.(.+)"> Order deny,allow deny from all </Files> </VirtualHost>

  Read the article

• Lockdown users on Windows Server 2012

  - by el.severo

  I set up a Active Directory on a server machine with Windows Server 2012 and I'd like to create some users with limitations like Windows Steady State does in Windows XP (locally). Seen already the Windows SteadyState Handbook (with Windows Server 2008), but I'd like to know if anyone has tried this before, the limitations are the following: 1. Prevent locked or roaming user profiles that cannot be found on the computer from logging on 2. Do not cache copies of locked or roaming user profiles for users who have previously logged on to this computer 3. Do not allow Windows to compute and store passwords using LAN Manager Hash values 4. Do not store usernames or passwords used to log on to the Windows Live ID or the domain 5. Prevent users from creating folders and files on drive C:\ 6. Lock profile to prevent the user from making permanent changes 7. Remove the Control Panel, Printer and Network Settings from the Classic Start menu 8. Remove the Favorites icon 9. Remove the My Network Places icon 10. Remove the Frequently Used Program list 11. Remove the Shared documents folder from My Computer 12. Remove control Panel icon 13. Remove the Set Program Access and Defaults icon 14. Remove the Network Connection(Connect To)icon 15. Remove the Printers and Faxes icon 16. Remove the Run icon 17. Prevent access to Windows Explorer features: Folder Options, Customize Toolbar, and the Notification Area 18. Prevent access to the taskbar 19. Prevent access to the command prompt 20. Prevent access to the registry editor 21. Prevent access to the Task Manager 22. Prevent access to Microsoft Management Console utilities 23. Prevent users from adding or removing printers 24. Prevent users from locking the computer 25. Prevent password changes (also requires the Control Panel icon to be removed) 26. Disable System Tools and other management programs 27. Prevent users from saving files to the desktop 28. Hide A Drive 29. Hide B Drive 30. Hide C Drive 31. Prevent changes to Internet Explorer registry settings 32. Empty the Temporary Internet Files folder when Internet Explorer is closed 33. Remove Internet Options 34. Remove General tab in Internet Options 35. Remove Security tab in Internet Options 36. Remove Privacy tab in Internet Options 37. Remove Content tab in Internet Options 38. Remove Connections tab in Internet Options 39. Remove Programs tab in Internet Options 40. Remove Advanced tab in Internet Options 41. Set a home page (Internet Explorer) 42. Restrict the possibility to change desktop image 43. Restrict the possibility to change wallpaper 44. Restrict usb flash drives Any suggestions for this? UPDATE: As @Dan suggested me I'd like to specify that would be applied to a educational scenario where students can login from a computer and want to add some restrictions to them.

  Read the article

• Oracle Insurance Unveils Next Generation of Enterprise Document Automation: Oracle Documaker Enterprise Edition

  - by helen.pitts(at)oracle.com

  Oracle today announced the introduction of Oracle Documaker Enterprise Edition, the next generation of the company's market-leading Enterprise Document Automation (EDA) solution for dynamically creating, managing and delivering adaptive enterprise communications across multiple channels. "Insurers and other organizations need enterprise document automation that puts the power to manage the complete document lifecycle in the hands of the business user," said Srini Venkatasanthanam, vice president, Product Strategy, Oracle Insurancein the press release. "Built with features such as rules-based configurability and interactive processing, Oracle Documaker Enterprise Edition makes possible an adaptive approach to enterprise document automation - documents when, where and in the form they're needed." Key enhancements in Oracle Documaker Enterprise Edition include: Documaker Interactive, the newly renamed and redesigned Web-based iDocumaker module. Documaker Interactive enables users to quickly and interactively create and assemble compliant communications such as policy and claims correspondence directly from their desktops. Users benefits from built-in accelerators and rules-based configurability, pre-configured content as well as embedded workflow leveraging Oracle BPEL Process Manager. Documaker Documaker Factory, which helps enterprises reduce cost and improve operational efficiency through better management of their enterprise publishing operations. Dashboards, analytics, reporting and an administrative console provide insurers with greater insight and centralized control over document production allowing them to better adapt their resources based on business demands. Other enhancements include: enhanced business user empowerment; additional multi-language localization capabilities; and benefits from the use of powerful Oracle technologies such as the Oracle Application Development Framework for all interfaces and Oracle Universal Content Management (Oracle UCM) for enterprise content management. Drive Competitive Advantage and Growth: Deb Smallwood, founder of SMA Strategy Meets Action, a leading industry insurance analyst consulting firm and co-author of 3CM in Insurance: Customer Communications and Content Management published last month, noted in the press release that "maximum value can be gained from investments when Enterprise Document Automation (EDA) is viewed holistically and all forms of communication and all types of information are integrated across the entire enterprise. "Insurers that choose an approach that takes all communications, both structured and unstructured data, coming into the company from a wide range of channels, and then create seamless flows of information will have a real competitive advantage," Smallwood said. "This capability will soon become essential for selling, servicing, and ultimately driving growth through new business and retention." Learn More: Click here to watch a short flash demo that demonstrates the real business value offered by Oracle Documaker Enterprise Edition. You can also see how an insurance company can use Oracle Documaker Enterprise Edition to dynamically create, manage and publish adaptive enterprise content throughout the insurance business lifecycle for delivery across multiple channels by visiting Alamere Insurance, a fictional model insurance company created by Oracle to showcase how Oracle applications can be leveraged within the insurance enterprise. Meet Our Newest Oracle Insurance Blogger: I'm pleased to introduce our newest Oracle Insurance blogger, Susanne Hale. Susanne, who manages product marketing for Oracle Insurance EDA solutions, will be sharing insights about this topic along with examples of how our customers are transforming their enterprise communications using Oracle Documaker Enterprise Edition in future Oracle Insurance blog entries. Helen Pitts is senior product marketing manager for Oracle Insurance.

  Read the article

• Using FiddlerCore to capture HTTP Requests with .NET

  - by Rick Strahl

  Over the last few weeks I’ve been working on my Web load testing utility West Wind WebSurge. One of the key components of a load testing tool is the ability to capture URLs effectively so that you can play them back later under load. One of the options in WebSurge for capturing URLs is to use its built-in capture tool which acts as an HTTP proxy to capture any HTTP and HTTPS traffic from most Windows HTTP clients, including Web Browsers as well as standalone Windows applications and services. To make this happen, I used Eric Lawrence’s awesome FiddlerCore library, which provides most of the functionality of his desktop Fiddler application, all rolled into an easy to use library that you can plug into your own applications. FiddlerCore makes it almost too easy to capture HTTP content! For WebSurge I needed to capture all HTTP traffic in order to capture the full HTTP request – URL, headers and any content posted by the client. The result of what I ended up creating is this semi-generic capture form: In this post I’m going to demonstrate how easy it is to use FiddlerCore to build this HTTP Capture Form.  If you want to jump right in here are the links to get Telerik’s Fiddler Core and the code for the demo provided here. FiddlerCore Download FiddlerCore on NuGet Show me the Code (WebSurge Integration code from GitHub) Download the WinForms Sample Form West Wind Web Surge (example implementation in live app) Note that FiddlerCore is bound by a license for commercial usage – see license.txt in the FiddlerCore distribution for details. Integrating FiddlerCore FiddlerCore is a library that simply plugs into your application. You can download it from the Telerik site and manually add the assemblies to your project, or you can simply install the NuGet package via:       PM> Install-Package FiddlerCore The library consists of the FiddlerCore.dll as well as a couple of support libraries (CertMaker.dll and BCMakeCert.dll) that are used for installing SSL certificates. I’ll have more on SSL captures and certificate installation later in this post. But first let’s see how easy it is to use FiddlerCore to capture HTTP content by looking at how to build the above capture form. Capturing HTTP Content Once the library is installed it’s super easy to hook up Fiddler functionality. Fiddler includes a number of static class methods on the FiddlerApplication object that can be called to hook up callback events as well as actual start monitoring HTTP URLs. In the following code directly lifted from WebSurge, I configure a few filter options on Form level object, from the user inputs shown on the form by assigning it to a capture options object. In the live application these settings are persisted configuration values, but in the demo they are one time values initialized and set on the form. Once these options are set, I hook up the AfterSessionComplete event to capture every URL that passes through the proxy after the request is completed and start up the Proxy service:void Start() { if (tbIgnoreResources.Checked) CaptureConfiguration.IgnoreResources = true; else CaptureConfiguration.IgnoreResources = false; string strProcId = txtProcessId.Text; if (strProcId.Contains('-')) strProcId = strProcId.Substring(strProcId.IndexOf('-') + 1).Trim(); strProcId = strProcId.Trim(); int procId = 0; if (!string.IsNullOrEmpty(strProcId)) { if (!int.TryParse(strProcId, out procId)) procId = 0; } CaptureConfiguration.ProcessId = procId; CaptureConfiguration.CaptureDomain = txtCaptureDomain.Text; FiddlerApplication.AfterSessionComplete += FiddlerApplication_AfterSessionComplete; FiddlerApplication.Startup(8888, true, true, true); } The key lines for FiddlerCore are just the last two lines of code that include the event hookup code as well as the Startup() method call. Here I only hook up to the AfterSessionComplete event but there are a number of other events that hook various stages of the HTTP request cycle you can also hook into. Other events include BeforeRequest, BeforeResponse, RequestHeadersAvailable, ResponseHeadersAvailable and so on. In my case I want to capture the request data and I actually have several options to capture this data. AfterSessionComplete is the last event that fires in the request sequence and it’s the most common choice to capture all request and response data. I could have used several other events, but AfterSessionComplete is one place where you can look both at the request and response data, so this will be the most common place to hook into if you’re capturing content. The implementation of AfterSessionComplete is responsible for capturing all HTTP request headers and it looks something like this:private void FiddlerApplication_AfterSessionComplete(Session sess) { // Ignore HTTPS connect requests if (sess.RequestMethod == "CONNECT") return; if (CaptureConfiguration.ProcessId > 0) { if (sess.LocalProcessID != 0 && sess.LocalProcessID != CaptureConfiguration.ProcessId) return; } if (!string.IsNullOrEmpty(CaptureConfiguration.CaptureDomain)) { if (sess.hostname.ToLower() != CaptureConfiguration.CaptureDomain.Trim().ToLower()) return; } if (CaptureConfiguration.IgnoreResources) { string url = sess.fullUrl.ToLower(); var extensions = CaptureConfiguration.ExtensionFilterExclusions; foreach (var ext in extensions) { if (url.Contains(ext)) return; } var filters = CaptureConfiguration.UrlFilterExclusions; foreach (var urlFilter in filters) { if (url.Contains(urlFilter)) return; } } if (sess == null || sess.oRequest == null || sess.oRequest.headers == null) return; string headers = sess.oRequest.headers.ToString(); var reqBody = sess.GetRequestBodyAsString(); // if you wanted to capture the response //string respHeaders = session.oResponse.headers.ToString(); //var respBody = session.GetResponseBodyAsString(); // replace the HTTP line to inject full URL string firstLine = sess.RequestMethod + " " + sess.fullUrl + " " + sess.oRequest.headers.HTTPVersion; int at = headers.IndexOf("\r\n"); if (at < 0) return; headers = firstLine + "\r\n" + headers.Substring(at + 1); string output = headers + "\r\n" + (!string.IsNullOrEmpty(reqBody) ? reqBody + "\r\n" : string.Empty) + Separator + "\r\n\r\n"; BeginInvoke(new Action<string>((text) => { txtCapture.AppendText(text); UpdateButtonStatus(); }), output); } The code starts by filtering out some requests based on the CaptureOptions I set before the capture is started. These options/filters are applied when requests actually come in. This is very useful to help narrow down the requests that are captured for playback based on options the user picked. I find it useful to limit requests to a certain domain for captures, as well as filtering out some request types like static resources – images, css, scripts etc. This is of course optional, but I think it’s a common scenario and WebSurge makes good use of this feature. AfterSessionComplete like other FiddlerCore events, provides a Session object parameter which contains all the request and response details. There are oRequest and oResponse objects to hold their respective data. In my case I’m interested in the raw request headers and body only, as you can see in the commented code you can also retrieve the response headers and body. Here the code captures the request headers and body and simply appends the output to the textbox on the screen. Note that the Fiddler events are asynchronous, so in order to display the content in the UI they have to be marshaled back the UI thread with BeginInvoke, which here simply takes the generated headers and appends it to the existing textbox test on the form. As each request is processed, the headers are captured and appended to the bottom of the textbox resulting in a Session HTTP capture in the format that Web Surge internally supports, which is basically raw request headers with a customized 1st HTTP Header line that includes the full URL rather than a server relative URL. When the capture is done the user can either copy the raw HTTP session to the clipboard, or directly save it to file. This raw capture format is the same format WebSurge and also Fiddler use to import/export request data. While this code is application specific, it demonstrates the kind of logic that you can easily apply to the request capture process, which is one of the reasonsof why FiddlerCore is so powerful. You get to choose what content you want to look up as part of your own application logic and you can then decide how to capture or use that data as part of your application. The actual captured data in this case is only a string. The user can edit the data by hand or in the the case of WebSurge, save it to disk and automatically open the captured session as a new load test. Stopping the FiddlerCore Proxy Finally to stop capturing requests you simply disconnect the event handler and call the FiddlerApplication.ShutDown() method:void Stop() { FiddlerApplication.AfterSessionComplete -= FiddlerApplication_AfterSessionComplete; if (FiddlerApplication.IsStarted()) FiddlerApplication.Shutdown(); } As you can see, adding HTTP capture functionality to an application is very straight forward. FiddlerCore offers tons of features I’m not even touching on here – I suspect basic captures are the most common scenario, but a lot of different things can be done with FiddlerCore’s simple API interface. Sky’s the limit! The source code for this sample capture form (WinForms) is provided as part of this article. Adding Fiddler Certificates with FiddlerCore One of the sticking points in West Wind WebSurge has been that if you wanted to capture HTTPS/SSL traffic, you needed to have the full version of Fiddler and have HTTPS decryption enabled. Essentially you had to use Fiddler to configure HTTPS decryption and the associated installation of the Fiddler local client certificate that is used for local decryption of incoming SSL traffic. While this works just fine, requiring to have Fiddler installed and then using a separate application to configure the SSL functionality isn’t ideal. Fortunately FiddlerCore actually includes the tools to register the Fiddler Certificate directly using FiddlerCore. Why does Fiddler need a Certificate in the first Place? Fiddler and FiddlerCore are essentially HTTP proxies which means they inject themselves into the HTTP conversation by re-routing HTTP traffic to a special HTTP port (8888 by default for Fiddler) and then forward the HTTP data to the original client. Fiddler injects itself as the system proxy in using the WinInet Windows settings  which are the same settings that Internet Explorer uses and that are configured in the Windows and Internet Explorer Internet Settings dialog. Most HTTP clients running on Windows pick up and apply these system level Proxy settings before establishing new HTTP connections and that’s why most clients automatically work once Fiddler – or FiddlerCore/WebSurge are running. For plain HTTP requests this just works – Fiddler intercepts the HTTP requests on the proxy port and then forwards them to the original port (80 for HTTP and 443 for SSL typically but it could be any port). For SSL however, this is not quite as simple – Fiddler can easily act as an HTTPS/SSL client to capture inbound requests from the server, but when it forwards the request to the client it has to also act as an SSL server and provide a certificate that the client trusts. This won’t be the original certificate from the remote site, but rather a custom local certificate that effectively simulates an SSL connection between the proxy and the client. If there is no custom certificate configured for Fiddler the SSL request fails with a certificate validation error. The key for this to work is that a custom certificate has to be installed that the HTTPS client trusts on the local machine. For a much more detailed description of the process you can check out Eric Lawrence’s blog post on Certificates. If you’re using the desktop version of Fiddler you can install a local certificate into the Windows certificate store. Fiddler proper does this from the Options menu: This operation does several things: It installs the Fiddler Root Certificate It sets trust to this Root Certificate A new client certificate is generated for each HTTPS site monitored Certificate Installation with FiddlerCore You can also provide this same functionality using FiddlerCore which includes a CertMaker class. Using CertMaker is straight forward to use and it provides an easy way to create some simple helpers that can install and uninstall a Fiddler Root certificate:public static bool InstallCertificate() { if (!CertMaker.rootCertExists()) { if (!CertMaker.createRootCert()) return false; if (!CertMaker.trustRootCert()) return false; } return true; } public static bool UninstallCertificate() { if (CertMaker.rootCertExists()) { if (!CertMaker.removeFiddlerGeneratedCerts(true)) return false; } return true; } InstallCertificate() works by first checking whether the root certificate is already installed and if it isn’t goes ahead and creates a new one. The process of creating the certificate is a two step process – first the actual certificate is created and then it’s moved into the certificate store to become trusted. I’m not sure why you’d ever split these operations up since a cert created without trust isn’t going to be of much value, but there are two distinct steps. When you trigger the trustRootCert() method, a message box will pop up on the desktop that lets you know that you’re about to trust a local private certificate. This is a security feature to ensure that you really want to trust the Fiddler root since you are essentially installing a man in the middle certificate. It’s quite safe to use this generated root certificate, because it’s been specifically generated for your machine and thus is not usable from external sources, the only way to use this certificate in a trusted way is from the local machine. IOW, unless somebody has physical access to your machine, there’s no useful way to hijack this certificate and use it for nefarious purposes (see Eric’s post for more details). Once the Root certificate has been installed, FiddlerCore/Fiddler create new certificates for each site that is connected to with HTTPS. You can end up with quite a few temporary certificates in your certificate store. To uninstall you can either use Fiddler and simply uncheck the Decrypt HTTPS traffic option followed by the remove Fiddler certificates button, or you can use FiddlerCore’s CertMaker.removeFiddlerGeneratedCerts() which removes the root cert and any of the intermediary certificates Fiddler created. Keep in mind that when you uninstall you uninstall the certificate for both FiddlerCore and Fiddler, so use UninstallCertificate() with care and realize that you might affect the Fiddler application’s operation by doing so as well. When to check for an installed Certificate Note that the check to see if the root certificate exists is pretty fast, while the actual process of installing the certificate is a relatively slow operation that even on a fast machine takes a few seconds. Further the trust operation pops up a message box so you probably don’t want to install the certificate repeatedly. Since the check for the root certificate is fast, you can easily put a call to InstallCertificate() in any capture startup code – in which case the certificate installation only triggers when a certificate is in fact not installed. Personally I like to make certificate installation explicit – just like Fiddler does, so in WebSurge I use a small drop down option on the menu to install or uninstall the SSL certificate:   This code calls the InstallCertificate and UnInstallCertificate functions respectively – the experience with this is similar to what you get in Fiddler with the extra dialog box popping up to prompt confirmation for installation of the root certificate. Once the cert is installed you can then capture SSL requests. There’s a gotcha however… Gotcha: FiddlerCore Certificates don’t stick by Default When I originally tried to use the Fiddler certificate installation I ran into an odd problem. I was able to install the certificate and immediately after installation was able to capture HTTPS requests. Then I would exit the application and come back in and try the same HTTPS capture again and it would fail due to a missing certificate. CertMaker.rootCertExists() would return false after every restart and if re-installed the certificate a new certificate would get added to the certificate store resulting in a bunch of duplicated root certificates with different keys. What the heck? CertMaker and BcMakeCert create non-sticky CertificatesI turns out that FiddlerCore by default uses different components from what the full version of Fiddler uses. Fiddler uses a Windows utility called MakeCert.exe to create the Fiddler Root certificate. FiddlerCore however installs the CertMaker.dll and BCMakeCert.dll assemblies, which use a different crypto library (Bouncy Castle) for certificate creation than MakeCert.exe which uses the Windows Crypto API. The assemblies provide support for non-windows operation for Fiddler under Mono, as well as support for some non-Windows certificate platforms like iOS and Android for decryption. The bottom line is that the FiddlerCore provided bouncy castle assemblies are not sticky by default as the certificates created with them are not cached as they are in Fiddler proper. To get certificates to ‘stick’ you have to explicitly cache the certificates in Fiddler’s internal preferences. A cache aware version of InstallCertificate looks something like this:public static bool InstallCertificate() { if (!CertMaker.rootCertExists()) { if (!CertMaker.createRootCert()) return false; if (!CertMaker.trustRootCert()) return false; App.Configuration.UrlCapture.Cert = FiddlerApplication.Prefs.GetStringPref("fiddler.certmaker.bc.cert", null); App.Configuration.UrlCapture.Key = FiddlerApplication.Prefs.GetStringPref("fiddler.certmaker.bc.key", null); } return true; } public static bool UninstallCertificate() { if (CertMaker.rootCertExists()) { if (!CertMaker.removeFiddlerGeneratedCerts(true)) return false; } App.Configuration.UrlCapture.Cert = null; App.Configuration.UrlCapture.Key = null; return true; } In this code I store the Fiddler cert and private key in an application configuration settings that’s stored with the application settings (App.Configuration.UrlCapture object). These settings automatically persist when WebSurge is shut down. The values are read out of Fiddler’s internal preferences store which is set after a new certificate has been created. Likewise I clear out the configuration settings when the certificate is uninstalled. In order for these setting to be used you have to also load the configuration settings into the Fiddler preferences *before* a call to rootCertExists() is made. I do this in the capture form’s constructor:public FiddlerCapture(StressTestForm form) { InitializeComponent(); CaptureConfiguration = App.Configuration.UrlCapture; MainForm = form; if (!string.IsNullOrEmpty(App.Configuration.UrlCapture.Cert)) { FiddlerApplication.Prefs.SetStringPref("fiddler.certmaker.bc.key", App.Configuration.UrlCapture.Key); FiddlerApplication.Prefs.SetStringPref("fiddler.certmaker.bc.cert", App.Configuration.UrlCapture.Cert); }} This is kind of a drag to do and not documented anywhere that I could find, so hopefully this will save you some grief if you want to work with the stock certificate logic that installs with FiddlerCore. MakeCert provides sticky Certificates and the same functionality as Fiddler But there’s actually an easier way. If you want to skip the above Fiddler preference configuration code in your application you can choose to distribute MakeCert.exe instead of certmaker.dll and bcmakecert.dll. When you use MakeCert.exe, the certificates settings are stored in Windows so they are available without any custom configuration inside of your application. It’s easier to integrate and as long as you run on Windows and you don’t need to support iOS or Android devices is simply easier to deal with. To integrate into your project, you can remove the reference to CertMaker.dll (and the BcMakeCert.dll assembly) from your project. Instead copy MakeCert.exe into your output folder. To make sure MakeCert.exe gets pushed out, include MakeCert.exe in your project and set the Build Action to None, and Copy to Output Directory to Copy if newer. Note that the CertMaker.dll reference in the project has been removed and on disk the files for Certmaker.dll, as well as the BCMakeCert.dll files on disk. Keep in mind that these DLLs are resources of the FiddlerCore NuGet package, so updating the package may end up pushing those files back into your project. Once MakeCert.exe is distributed FiddlerCore checks for it first before using the assemblies so as long as MakeCert.exe exists it’ll be used for certificate creation (at least on Windows). Summary FiddlerCore is a pretty sweet tool, and it’s absolutely awesome that we get to plug in most of the functionality of Fiddler right into our own applications. A few years back I tried to build this sort of functionality myself for an app and ended up giving up because it’s a big job to get HTTP right – especially if you need to support SSL. FiddlerCore now provides that functionality as a turnkey solution that can be plugged into your own apps easily. The only downside is FiddlerCore’s documentation for more advanced features like certificate installation which is pretty sketchy. While for the most part FiddlerCore’s feature set is easy to work with without any documentation, advanced features are often not intuitive to gleam by just using Intellisense or the FiddlerCore help file reference (which is not terribly useful). While Eric Lawrence is very responsive on his forum and on Twitter, there simply isn’t much useful documentation on Fiddler/FiddlerCore available online. If you run into trouble the forum is probably the first place to look and then ask a question if you can’t find the answer. The best documentation you can find is Eric’s Fiddler Book which covers a ton of functionality of Fiddler and FiddlerCore. The book is a great reference to Fiddler’s feature set as well as providing great insights into the HTTP protocol. The second half of the book that gets into the innards of HTTP is an excellent read for anybody who wants to know more about some of the more arcane aspects and special behaviors of HTTP – it’s well worth the read. While the book has tons of information in a very readable format, it’s unfortunately not a great reference as it’s hard to find things in the book and because it’s not available online you can’t electronically search for the great content in it. But it’s hard to complain about any of this given the obvious effort and love that’s gone into this awesome product for all of these years. A mighty big thanks to Eric Lawrence  for having created this useful tool that so many of us use all the time, and also to Telerik for picking up Fiddler/FiddlerCore and providing Eric the resources to support and improve this wonderful tool full time and keeping it free for all. Kudos! Resources FiddlerCore Download FiddlerCore NuGet Fiddler Capture Sample Form Fiddler Capture Form in West Wind WebSurge (GitHub) Eric Lawrence’s Fiddler Book© Rick Strahl, West Wind Technologies, 2005-2014Posted in .NET  HTTP   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• unity screensaver ? - plans for unity

  - by gare

  Are there plans to develop a screensaver specifically for Unity? Since Unity uses gnome-screensaver by default currently, seems like a reasonable area for a desktop to attract much user appreciation. (My personal interest is in a nice Pictures folder type slideshow screensaver with more settings than currently offered in gnome-screensaver - ie folder specification, and duration/delay of slide.) Thank you.

  Read the article

• Xubuntu 13.10 64bit - Slow and buggy "log out" process?

  - by MrKatSwordfish

  I'm a Windows convert who has done only a little bit of dabbling in Ubuntu in the past (back in Dapper Drake a few years back). A lot has changes since then, and I've been yearning to jump back into linux again! So, having just bought a new SSD, I felt that this would be as good of a time as any to set up a dual-boot system again. I've messed around with Ubuntu 13.10 a bit, and while Unity has its issues, I think that it still needs some time to develop. I looked into XFCE and liked it a lot, so I went with Xubuntu. I've installed Xubuntu, and for the most part it's running smoothly and it a pleasure to work with. The customization is great and the minimalistic look and feel is really nice! But here's my problem, whenever I select the "Log Out" option from either the application menu, or the user profiles menu, my PC comes to a crawl, and the dialog box with all the options (shut down, restart, log out, etc.) takes maybe a minute or more to appear. I click the log out button, my PC is brought to a snail's pace, and I have to wait for what seems like an eternity for the logout options to appear! If i try to open something else (even a terminal window) while it's loading the logout options, that other program won't finish loading until the logout screen finally appears. Keep in mind, this is a pretty much vanilla install of Xubuntu 13.10 64bit, on a PC with an intel i7, an SSD, 6gb DDR3 RAM, and a new AMD 7770 gpu (drivers haven't been installed yet, though). Everything else runs fast, most applications open near-instantly! It must be an issue with how the logout options screen initializes or something, but I'm not sure exactly how I can fix it.. Edit - Extra Info: This problem is very consistent when using the "Log Out" buttons in Xubuntu. However, I've found that I'm able to reboot and shutdown much more quickly by going through the "Switch User" screen, and using the reboot or shutdown buttons on that screen. I'm nearly certain that it has something to do with the little Log Out options screen that appears when I select Log Out from the menu, and not the actual process of shutting down.. So what should I do? I really like XFCE so far, and I've never tried a non-ubuntu based distro before, but should I just switch to something else? Is there any known fix for this issue? Are there any work-arounds for logging out/shutting down/rebooting via the terminal so that I can avoid this irritating bug? Is there any that I can monitor the progress of the log out via terminal, allowing me to see which parts are causing the slow-down? What is the best way to report this bug to someone?

  Read the article

• How to remove MySQL completely with config and library files on ubuntu 12.04 gnome 3.0

  - by codeartist

  I tried everything till now: sudo apt-get remove mysql-server mysql-client mysql-common sudo apt-get purge mysql-server mysql-client mysql-common sudo apt-get autoremove and even more commands... But whenever I am trying to locate mysql. I get a no. of files related to mysql command: shell>> locate mysql Output: /etc/mysql /etc/apparmor.d/usr.sbin.mysqld /etc/apparmor.d/abstractions/mysql /etc/apparmor.d/cache/usr.sbin.mysqld /etc/apparmor.d/cache/usr.sbin.mysqld-akonadi /etc/apparmor.d/local/usr.sbin.mysqld /etc/bash_completion.d/mysqladmin /etc/init/mysql.conf /etc/logcheck/ignore.d.paranoid/mysql-server-5_5 /etc/logcheck/ignore.d.server/mysql-server-5_5 /etc/logcheck/ignore.d.workstation/mysql-server-5_5 /etc/logrotate.d/mysql-server /etc/mysql/conf.d /etc/mysql/debian-start /etc/mysql/debian.cnf /etc/mysql/conf.d/mysqld_safe_syslog.cnf /home/pkr/.mysql_history /home/pkr/.cache/software-center/piston-helper/rec.ubuntu.com,api,1.0,recommend_app,libqt4-sql-mysql,,349051c3a57da571aa832adb39177aff /home/pkr/.cache/software-center/piston-helper/rec.ubuntu.com,api,1.0,recommend_app,mysql-client,,cbf77a486cdc80547317981a33144427 /home/pkr/.cache/software-center/piston-helper/rec.ubuntu.com,api,1.0,recommend_app,mysql-client,,de8220dee4d957a9502caa79e8d2fdda /home/pkr/.cache/software-center/rnrclient/reviews.ubuntu.com,reviews,api,1.0,reviews,filter,en,any,any,any,libqt4-sql-mysql,page,1,helpful,,17fb2e657321dc51526ee8fe9928da30 /home/pkr/.cache/software-center/rnrclient/reviews.ubuntu.com,reviews,api,1.0,reviews,filter,en,any,any,any,mysql-client,page,1,helpful,,a4c1b6e8200f36ab5745c6f81f14da0a /home/pkr/.cache/software-center/rnrclient/reviews.ubuntu.com,reviews,api,1.0,reviews,filter,en,ubuntu,oneiric,any,libqt4-sql-mysql,page,1,helpful,,c54295fb82b8183350cd34f22c3547ef /home/pkr/.cache/software-center/rnrclient/reviews.ubuntu.com,reviews,api,1.0,reviews,filter,en,ubuntu,oneiric,any,mysql-client,page,1,helpful,,fcf201c1abff3f774af89173a84de2cc /home/pkr/.cache/software-center/rnrclient/reviews.ubuntu.com,reviews,api,1.0,reviews,filter,en,ubuntu,precise,any,libqt4-sql-mysql,page,1,helpful,,0cd86648584efeccfb16119012f89540 /home/pkr/.cache/software-center/rnrclient/reviews.ubuntu.com,reviews,api,1.0,reviews,filter,en,ubuntu,precise,any,mysql-client,page,1,helpful,,eb84724e9da7851ff8862a227d8bac59 /home/pkr/.local/share/akonadi/mysql.conf /home/pkr/.local/share/akonadi/db_data/mysql /home/pkr/.local/share/akonadi/db_data/mysql.err /home/pkr/.local/share/akonadi/db_data/mysql.err.old /home/pkr/.local/share/akonadi/db_data/mysql/columns_priv.MYD /home/pkr/.local/share/akonadi/db_data/mysql/columns_priv.MYI /home/pkr/.local/share/akonadi/db_data/mysql/columns_priv.frm /home/pkr/.local/share/akonadi/db_data/mysql/db.MYD /home/pkr/.local/share/akonadi/db_data/mysql/db.MYI /home/pkr/.local/share/akonadi/db_data/mysql/db.frm /home/pkr/.local/share/akonadi/db_data/mysql/event.MYD /home/pkr/.local/share/akonadi/db_data/mysql/event.MYI /home/pkr/.local/share/akonadi/db_data/mysql/event.frm /home/pkr/.local/share/akonadi/db_data/mysql/func.MYD /home/pkr/.local/share/akonadi/db_data/mysql/func.MYI /home/pkr/.local/share/akonadi/db_data/mysql/func.frm /home/pkr/.local/share/akonadi/db_data/mysql/general_log.CSM /home/pkr/.local/share/akonadi/db_data/mysql/general_log.CSV /home/pkr/.local/share/akonadi/db_data/mysql/general_log.frm /home/pkr/.local/share/akonadi/db_data/mysql/help_category.MYD /home/pkr/.local/share/akonadi/db_data/mysql/help_category.MYI /home/pkr/.local/share/akonadi/db_data/mysql/help_category.frm /home/pkr/.local/share/akonadi/db_data/mysql/help_keyword.MYD /home/pkr/.local/share/akonadi/db_data/mysql/help_keyword.MYI /home/pkr/.local/share/akonadi/db_data/mysql/help_keyword.frm /home/pkr/.local/share/akonadi/db_data/mysql/help_relation.MYD /home/pkr/.local/share/akonadi/db_data/mysql/help_relation.MYI /home/pkr/.local/share/akonadi/db_data/mysql/help_relation.frm /home/pkr/.local/share/akonadi/db_data/mysql/help_topic.MYD /home/pkr/.local/share/akonadi/db_data/mysql/help_topic.MYI /home/pkr/.local/share/akonadi/db_data/mysql/help_topic.frm /home/pkr/.local/share/akonadi/db_data/mysql/host.MYD /home/pkr/.local/share/akonadi/db_data/mysql/host.MYI /home/pkr/.local/share/akonadi/db_data/mysql/host.frm /home/pkr/.local/share/akonadi/db_data/mysql/ndb_binlog_index.MYD /home/pkr/.local/share/akonadi/db_data/mysql/ndb_binlog_index.MYI /home/pkr/.local/share/akonadi/db_data/mysql/ndb_binlog_index.frm /home/pkr/.local/share/akonadi/db_data/mysql/plugin.MYD /home/pkr/.local/share/akonadi/db_data/mysql/plugin.MYI /home/pkr/.local/share/akonadi/db_data/mysql/plugin.frm /home/pkr/.local/share/akonadi/db_data/mysql/proc.MYD /home/pkr/.local/share/akonadi/db_data/mysql/proc.MYI /home/pkr/.local/share/akonadi/db_data/mysql/proc.frm /home/pkr/.local/share/akonadi/db_data/mysql/procs_priv.MYD /home/pkr/.local/share/akonadi/db_data/mysql/procs_priv.MYI /home/pkr/.local/share/akonadi/db_data/mysql/procs_priv.frm /home/pkr/.local/share/akonadi/db_data/mysql/proxies_priv.MYD /home/pkr/.local/share/akonadi/db_data/mysql/proxies_priv.MYI /home/pkr/.local/share/akonadi/db_data/mysql/proxies_priv.frm /home/pkr/.local/share/akonadi/db_data/mysql/servers.MYD /home/pkr/.local/share/akonadi/db_data/mysql/servers.MYI /home/pkr/.local/share/akonadi/db_data/mysql/servers.frm /home/pkr/.local/share/akonadi/db_data/mysql/slow_log.CSM /home/pkr/.local/share/akonadi/db_data/mysql/slow_log.CSV /home/pkr/.local/share/akonadi/db_data/mysql/slow_log.frm /home/pkr/.local/share/akonadi/db_data/mysql/tables_priv.MYD /home/pkr/.local/share/akonadi/db_data/mysql/tables_priv.MYI /home/pkr/.local/share/akonadi/db_data/mysql/tables_priv.frm /home/pkr/.local/share/akonadi/db_data/mysql/time_zone.MYD /home/pkr/.local/share/akonadi/db_data/mysql/time_zone.MYI /home/pkr/.local/share/akonadi/db_data/mysql/time_zone.frm /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_leap_second.MYD /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_leap_second.MYI /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_leap_second.frm /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_name.MYD /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_name.MYI /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_name.frm /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_transition.MYD /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_transition.MYI /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_transition.frm /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_transition_type.MYD /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_transition_type.MYI /home/pkr/.local/share/akonadi/db_data/mysql/time_zone_transition_type.frm /home/pkr/.local/share/akonadi/db_data/mysql/user.MYD /home/pkr/.local/share/akonadi/db_data/mysql/user.MYI /home/pkr/.local/share/akonadi/db_data/mysql/user.frm /usr/bin/mysql /usr/bin/mysql_install_db /usr/bin/mysql_upgrade /usr/bin/mysqlcheck /usr/sbin/mysqld /usr/share/mysql /usr/share/app-install/desktop/gmysqlcc:gmysqlcc.desktop /usr/share/app-install/desktop/mysql-client.desktop /usr/share/app-install/desktop/mysql-navigator:mysql-navigator.desktop /usr/share/app-install/desktop/mysql-server.desktop /usr/share/app-install/icons/gmysqlcc-32.png /usr/share/app-install/icons/mysql-navigator.png /usr/share/doc/mysql-client-core-5.5 /usr/share/doc/mysql-server-core-5.5 /usr/share/kde4/apps/katepart/syntax/sql-mysql.xml /usr/share/man/man1/mysql.1.gz /usr/share/man/man1/mysql_install_db.1.gz /usr/share/man/man1/mysql_upgrade.1.gz /usr/share/man/man1/mysqlcheck.1.gz /usr/share/man/man8/mysqld.8.gz /var/cache/apt/archives/akonadi-backend-mysql_1.7.2-0ubuntu1_all.deb /var/cache/apt/archives/libmysqlclient-dev_5.5.22-0ubuntu1_i386.deb /var/cache/apt/archives/libmysqlclient18_5.5.22-0ubuntu1_i386.deb /var/cache/apt/archives/libqt4-sql-mysql_4%3a4.8.1-0ubuntu4.1_i386.deb /var/cache/apt/archives/mysql-client-5.5_5.5.22-0ubuntu1_i386.deb /var/cache/apt/archives/mysql-client-core-5.5_5.5.22-0ubuntu1_i386.deb /var/cache/apt/archives/mysql-client_5.5.22-0ubuntu1_all.deb /var/cache/apt/archives/mysql-common_5.5.22-0ubuntu1_all.deb /var/cache/apt/archives/mysql-server-5.5_5.5.22-0ubuntu1_i386.deb /var/cache/apt/archives/mysql-server-core-5.5_5.5.22-0ubuntu1_i386.deb /var/cache/apt/archives/mysql-server_5.5.22-0ubuntu1_all.deb /var/lib/dpkg/info/mysql-client-core-5.5.list /var/lib/dpkg/info/mysql-client-core-5.5.md5sums /var/lib/dpkg/info/mysql-server-5.5.list /var/lib/dpkg/info/mysql-server-5.5.postrm /var/lib/dpkg/info/mysql-server-core-5.5.list /var/lib/dpkg/info/mysql-server-core-5.5.md5sums /var/log/mysql /var/log/mysql.err /var/log/mysql.log /var/log/mysql.log.1.gz /var/log/mysql.log.2.gz /var/log/mysql.log.3.gz /var/log/mysql.log.4.gz /var/log/mysql.log.5.gz /var/log/mysql.log.6.gz /var/log/mysql.log.7.gz /var/log/upstart/mysql.log.1.gz /var/log/upstart/mysql.log.2.gz /var/log/upstart/mysql.log.3.gz /var/log/upstart/mysql.log.4.gz /var/log/upstart/mysql.log.5.gz /var/log/upstart/mysql.log.6.gz /var/log/upstart/mysql.log.7.gz What should I do now? Please help me out in this :( I was trying to find out if there is any way I can remove mysql related every file and then reinstall mysql. I need it for Qt connectivity. I don't understand what to do! Please help :(

  Read the article

• Using PHP OCI8 with 32-bit PHP on Windows 64-bit

  - by christopher.jones

  The world migration from 32-bit to 64-bit operating systems is gaining pace. However I've seen a couple of customers having difficulty with the PHP OCI8 extension and Oracle DB on Windows 64-bit platforms. The errors vary depending how PHP is run. They may appear in the Apache or PHP log: Unable to load dynamic library 'C:\Program Files (x86)\PHP\ext\php_oci8_11g.dll' - %1 is not a valid Win32 application. or Warning oci_connect(): OCIEnvNlsCreate() failed. There is something wrong with your system - please check that PATH includes the directory with Oracle Instant Client libraries Other than IIS permission issues a common cause seems to be trying to use PHP with libraries from an Oracle 64-bit database on the same machine. There is currently no 64-bit version of PHP on http://php.net/ so there is a library mismatch. A solution is to install Oracle Instant Client 32-bit and make sure that PHP uses these libraries, while not interferring with the 64-bit database on the same machine. Warning: The following hacky steps come untested from a Linux user: Unzip Oracle Instant Client 32-bit and move it to C:\WINDOWS\SYSWOW64\INSTANTCLIENT_11_2. You may need to do this in a console with elevated permissions. Edit your PATH environment variable and insert C:\WINDOWS\SYSTEM32\INSTANTCLIENT_11_2 in the directory list before the entry for the Oracle Home library. Windows makes it so all 32-bit applications that reference C:\WINDOWS\SYSTEM32 actually see the contents of the C:\WINDOWS\SYSWOW64 directory. Your 64-bit database won't find an Instant Client in the real, physical C:\WINDOWS\SYSTEM32 directory and will continue to use the database libraries. Some of our Windows team are concerned about this hack and prefer a more "correct" solution that (i) doesn't require changing the Windows system directory (ii) doesn't add to the "memory" burden about what was configured on the system (iii) works when there are multiple database versions installed. The solution is to write a script which will set the 64-bit (or 32-bit) Oracle libraries in the path as needed before invoking the relevant bit-ness application. This does have a weakness when the application is started as a service. As a footnote: If you don't have a local database and simply need to have 32-bit and 64-bit Instant Client accessible at the same time, try the "symbolic" link approach covered in the hack in this OTN forum thread. Reminder warning: This blog post came untested from a Linux user.

  Read the article

• CodePlex Daily Summary for Friday, March 12, 2010

  CodePlex Daily Summary for Friday, March 12, 2010New Projects.NET DEPENDENCY INJECTION: Abel Perez Enterprise FrameworkAutodocs - WCF REST Automatic API Documentation Generator: Autodocs is an automatic API documentation generator for .NET applications that use Windows Communication Foundation (WCF) to establish REST API's.BlockBlock: Block Block is a free game. You know Lumines and you will like BlockBlock.C4F XNA ASCII Post-Processing: This is the source code for the Coding4Fun article "XNA Effects – ASCII Art in 3D"ChequePrinter: this is ChequePrinterCompiladores MSIL usando Phoenix (PLP 2008.1 - CIn/UFPE): Este projeto foi feito com o intuito de explorar a plataforma Microsoft Phoenix para a construção de compiladores para MSIL de duas linguagens de E...CRM External View: CRM External View enables more robust control over exposing Microsoft CRM data (in a form of views) for external parties. The solution uses web ser...CS Project2: This is for the projectDotNetNuke IM Module of Facebook Like Messenger: Help you integrate 123 Web Messenger into DotNetNuke, and add a powerful 1-to-1 IM Software named "Facebook Messenger Style Web Chat Bar" at the bo...DotNetNuke® RadPanelBar: DNNRadPanelBar makes it easy to add telerik RadPanelBar functionality to your module or skin. Licensing permits anyone to use the components (incl...DotNetNuke® Skin Blocks: A DotNetNuke Design Challenge skin package submitted to the "Modern Business" category by Armand Datema of Schwingsoft. This skin uses a bit of jQu...Drilltrough and filtering on SSAS-cubes in SSRS: We will describe a technique to create Reporting services (SSRS) reports that use Analysis services (SSAS) cubes as data sources, have a very intu...Ecosystem Diagnosis & Treatment: The Ecosystem DIagnosis & Treatment community provides tools, analyses and applications of the medical model to natural resource problems. EDT sof...ExIf 35: A utility for use by film photographers for keeping track of critical facts about images taken on a roll of film, just as digital cameras do automa...FabricadeTI: Desenvolvimento do framework FabricadeTI.Find and Replace word in the sentences: This program used Java Development Kid 6.0 and i were using HighLighter class. It was completed code with source code and then everybody can use in...Flash Nut: Flash Nut is a flash card program. You can build and review decks of flash cards. The project is a vs2008 wpf application.Free DotNetNuke Chat Module (Popup Mode): With this free DotNetNuke Chat Module (Popup Mode), master will assist to integrate DotNetNuke with 123 Flash Chat seamlessly, and add a popup mode...Free DotNetNuke IM of 123 Web Messenger -- Web-based Friend List: With this FREE application, you could integrate DNN website Database with 123 Web Messenger seamlessly and embed a web-based Friends List into anyw...Free DotNetNuke Live Help Module: With DotNetNuke Live Help Module, integrate 123 Live Help into DotNetNuke website and add Live Chat Button anywhere you like. Let visitors to chat ...G52GRP Videowall: NottinghamHappy Turtle Plugins for BVI :: Repository Based Versioning for Visual Studio: The Happy Turtle project creates plugins for the Build Version Increment Add-In for Visual Studio (BVI). The focus is to automatically version asse...Hasher: Hasher es capaz de generar el hash MD5 y SHA de textos de hasta 100.000 caracteres y ficheros. También te permitirá comprobar dos hash para verifi...Infragistics Silverlight Extended Controls: This project is a group of controls that extend or add functionality to the Infragistics Silverlight control suite. This control requires Infragis...Insert Video Jnr: This is a baby version of my Video plugin, it is intended for Hosted Wordpress blogs only and shouldn't be used with other blog providers.jccc .NET smart framework: jccc .NET smart framework allows the creation of fast connections to MSSQL or MYSQL databases, and the data manipulation by using of c# class's tha...LytScript: 函数式脚本语言Microsoft - DDD NLayerApp .NET 4.0 Example (Microsoft Spain): DDD NLayered App .NET 4.0 Example By Microsoft - Spain Domain Driven Design NLayered App .NET 4.0 Example Implementation Example of our local Arc...mimiKit: Lightweight ASP.NET MVC / Javascript Framework for creating mobile applications PHPWord: With PHPWord you can easily create a Word document with PHP. PHPWord creates docx Files that can include all major word functions like TextElements...Protocol Transition with BizTalk: An example solution the shows how todo Protocol Transition with BizTalk. This also shows you how to create a WCF extension to allow this to happen.Raid Runner: Raid Runner makes it easier to run and manage raid in World of Warcraft. It is a Silverlight application developed in c#SQL Server Authentication Troubleshooter: SQL Server Authentication Troubleshooter is a tool to help investigate a root cause of ‘Login Failed’ error in SQL Server. There could be number of...SuperviseObjects: SuperviseObjects consists of a collection which is derived from ObservableCollection<T>. This collection fires ItemPropertyChanging and ItemPropert...Viuto: Viuto.NET project aims to create a fully track and trace application. It is developed in: - Java & C: Firmware - C#: Parser - Asp.net: Tracki...Zealand IT MSBuild Tasks: Zealand IT MSBuild Tasks is a collection that you cannot do without if you are serious about continous integration. Ever wish you could specify an...New ReleasesASP.NET: ASP.NET MVC 2 RTM: This release contains the source code for ASP.NET MVC 2 RTM as well as the ASP.NET MVC Futures project. The futures project contains features that ...C#Mail: Higuchi.Mail.dll (2010.3.11 ver): Higuchi.Mail.dll at 2010-3-11 version.C#Mail: Higuchi.MailServer.dll (2010.3.11 ver): Higuchi.MailServer.dll at 2010.3.11 version.C4F XNA ASCII Post-Processing: XNA ASCII FPS v1 - Full Version: This is the full, complete example of the XNA ASCII FPS.C4F XNA ASCII Post-Processing: XNA ASCII FPS v1.0 - Base Project: This is the base project to be used by those who plan to follow along the Coding4Fun article.CRM External View: 1.0: Release 1.0DevTreks -social budgeting that improves lives and livelihoods: Social Budgeting Web Software, DevTreks alpha 3c: Alpha 3c upgrades custom/virtual uris (devpacks), temp uris, and zip packages. This is believed to be the first fully functional/performant release.DotNetNuke® RadPanelBar: DNNRadPanelBar 1.0.0: DNNRadPanelBar makes it easy to add telerik RadPanelBar functionality to your module or skin. Licensing permits anyone to use the components (inclu...Drilltrough and filtering on SSAS-cubes in SSRS: Release 1: Release 1ExIf 35: ExIf 35: Daily build of ExIf 35Family Tree Analyzer: Version 1.0.3.0: Version 1.0.3.0 Added options to check for updates on load and on help menu Disable use of US census for now until dealt with years being differen...Family Tree Analyzer: Version 1.0.4.0: Version 1.0.4.0 Added support for display of Ahnenfatel numbers Added filter to hide individuals from Lost Cousins report that have been flagged a...Flash Nut: Flash Nut 1.0 Setup: Flash Nut SetupFluent Validation for .NET: 1.2 RC: This is the release candidate for FluentValidation 1.2. If no bugs are found within the next couple of weeks, then this will become the 1.2 Final b...Free DotNetNuke Chat Module (Popup Mode): Download DNN Chat Module (Popup Mode)+Source Code: Feel free to download DotNetNuke Chat Module (Popup Mode), integrating DotNetNuke with 123 Flash Chat Software, and add a free popup mode flash cha...Free DotNetNuke Live Help Module: Download DNN Live Support Module and Source Code: In Readme file, there are detailed Installation and Integration Manual for you. This module is compatible with DotNetNuke v5.x.Happy Turtle Plugins for BVI :: Repository Based Versioning for Visual Studio: Happy Turtle 1.0.44927: This is the first release of the SVN based version incrementor. How To InstallMake sure that Build Version Increment v2.2.10065.1524 or newer is i...Hasher: 1.0: Versión inicial de la aplicación: Obtención de hash MD5 y SHA. Codificación en tiempo real de textos de hasta 100.000 caracteres. Codificación ...Jamolina: PhotosynthDemo: PhotosynthDemoMapWindow GIS: MapWindow 6.0 msi (March 11): This fixes an PixelToProj problem for the Extended Buffer case, as well as adding fixes to the WKBFeatureReader to fix an X,Y reversal and some ext...Math.NET Numerics: 2010.3.11.291 Build: Latest alpha buildMicrosoft - DDD NLayerApp .NET 4.0 Example (Microsoft Spain): V0.5 - N-Layer DDD Sample App: Required Software (Microsoft Base Software needed for Development environment) Unity Application Block 1.2 - October 2008 http://www.microsoft.com/...MiniTwitter: 1.09.2: MiniTwitter 1.09.2 更新内容 修正 タイムラインを削除すると落ちるバグを修正 稀にタイムラインのスクロールが出来ないバグを修正Nestoria.NET: Nestoria.NET 0.8: Provides access to the Nestoria API. Documentation contains a basic getting started guide. Please visit Darren Edge's blog for ongoing developmen...Pod Thrower: Version 1.0: Here is version 1.0. It has all the features I was looking to do in it. Please let me know if you use this and if you would like any changes.SharePoint Ad Rotator: SPAdRotator 2.0 Beta: This new release of the Ad Rotator contains many new features. One major new feature is that jQuery has been added to do image rotation without hav...SharePoint Objects: Democode Ton Stegeman: These download contains sample code for some SharePoint 2007 blog posts: TST.Themes_Build20100311.zip contains a feature receiver that registers Sh...SharePoint Taxonomy Extensions: SharePoint Taxonomy Extensions 1.2: Make Taxonomy Extensions useable in every list type. Not only in document libraries.SharePoint Video Player Web Part & SharePoint Video Library: Version 3.0.0: Absolutely killer feature - installing multiple players on a page without any loss of performance.SilverLight Interface for Mapserver: SLMapViewer v. 1.0: SLMapviewer sample application version 1.0. This new release includes the following enhancements: Silverlight 3.0 native Added a new init parame...Spark View Engine: Spark v1.1: Changes since RC1Built against ASP.NET MVC 2 RTMSPSS .NET interop library: 2.0: This new version supports SPSS 15, and includes spssio32.dll and other native .dll dependencies so that it works out of the box without SPSS being ...stefvanhooijdonk.com: SharePoint2010.ProfilePicturesLoader: So, with the help of Reflector, I wrote a small tool that would import all our profile pictures and update the user profiles. http://wp.me/pMnlQ-6G SuperviseObjects: SuperviseObjects 1.0: First releaseTortoiseSVN Addin for Visual Studio: TortoiseSVN Addin 1.0.5: Feature: Visual Studio/svn action synchronization on Item in Solution explorer like add, move, delete and rename. Note: Move action does not rememb...VCC: Latest build, v2.1.30311.0: Automatic drop of latest buildVivoSocial: VivoSocial 7.0.4: Business Management ■This release fixes a Could not load type error on the main view of the module. Groups ■Group requests were failing in some i...WikiPlex – a Regex Wiki Engine: WikiPlex 1.3: Info: Official Version: 1.3.0.215 | Full Release Notes Documentation - This new documentation includes Full Markup Guide with Examples Articles ...Zealand IT MSBuild Tasks: Zealand IT MSBuild Tasks: Initial beta release of Zealand IT MSBuild Tasks. Contains the following tasks: RunAs - Same as Exec task, but provides parameters for impersonat...ZoomBarPlus: V1 (Beta): This is the initial release. It should be considered a beta test version as it has not been tested for very long on my device.Most Popular ProjectsMetaSharpWBFS ManagerRawrAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)ASP.NET Ajax LibraryASP.NETMicrosoft SQL Server Community & SamplesMost Active ProjectsUmbraco CMSRawrN2 CMSBlogEngine.NETFasterflect - A Fast and Simple Reflection APIjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryFarseer Physics EngineCaliburn: An Application Framework for WPF and SilverlightSharePoint Team-Mailer

  Read the article

• SSIS - Access Denied with UNC paths - The file name is a device or contains invalid characters

  - by simonsabin

  I spent another day tearing my hair out yesterday trying to resolve an issue with SSIS packages runnning in SQLAgent (not got much left at the moment, maybe I should contact the SSIS team for a wig). My situation was that I am deploying packages to a development server, and to provide isolation I was running jobs with a proxy account that only had access to the development servers. Proxies are an awesome feature and mean that you should never have to "just run the job as sysadmin". The issue I was facing was that the job step was failing. The job step was a simple execution of the package.The following errors appeared in my log file. I always check the "Log step output in history" for a job step, this ensures you get all the output from the command that you run. I'll blog about this later. If looking at the output in sysdtslog90 then you will have an entry with datacode -1073573533 and error message File or directory "<filename>" represented by connection "<connection>" does not exist.  Not exactly helpful. If you get the output from the console then you will also get these errors. 0xC0202070 "The file name property is not valid. The file name is a device or contains invalid characters." 0xC001401E "specified in the connection was not valid." It appears this error is due to the use of a UNC path and the account runnnig the package not having access to all the folders in the path. Solution To solve this you need to ensure that the proxy account has access to ALL folders in the path you are accessing. To check this works, logon as the relevant proxy user, or run a command window as the specified user. Then try and do net use \\server\share and then do a dir for each folder in the path and check you have access. If these work and you still have the problem then you have some other problem, sorry. The following are posts on experts exchange that also discuss this,http://www.experts-exchange.com/Microsoft/Development/MS-SQL-Server/SSIS/Q_24056047.htmlhttp://www.experts-exchange.com/Microsoft/Development/MS-SQL-Server/SSIS/Q_23968903.html This blog had a post about it being a 64 bit issue. That definitely wasn't the issue for me as I was on a 32 bit server http://blogs.perkinsconsulting.com/post/64-bit-SQL-Server-2005-SSIS-and-UNC-paths-Part-2.aspx  

  Read the article

• Generating a twitter OAuth access key - the semi-manual way

  - by Piet

  [UPDATE] Apparently someone at Twitter was listening, or I’m going senile/blind. Let’s call it a combination of both. Instead of following all the steps below, you could just login with the Twitter account you want to use on http://dev.twitter.com, register your application and then click ‘Edit Details’ on the application overview page at http://dev.twitter.com/apps. Next click the ‘Application detail’ button on the right, followed by the ‘My Access Token’ button in order to get your Access Token and Access Token Secret. This makes the old post below rather obsolete. Clearly a case of me thinking everything is a nail and ruby is a hammer (don’t they usually say this about java coders?) [ORIGINAL POST] OAuth is great! OAuth allows your application to use your user’s data without the need to ask for their password. So Twitter made the API much safer for their and your users. Hurray! Free pizza for everyone! Unless of course you’re using the Twitter API for your own needs like running your own bot and don’t need access to other user’s data. In such cases a simple username/password combination is more than enough. I can understand however that the Twitter guys don’t really care that much about these exceptions(?). Most such uses for the API are probably rather spammy in nature. !!! If you have a twitter app that uses the API to access external user’s data: look for another solution. This solution is ONLY meant when you ONLY need access to your own account(s) through the API. Other Solutions Mr Dallas Devries posted a solution here which involves requesting and scraping a one-time PIN. But: I like to minimize the amount of calls I make to twitter’s API or pages to lessen my chances of meeting the fail whale. Also, as soon as the pin isn’t included in a div called ‘oauth_pin’ anymore, this will fail. However, mr Devries’ post was a starting point for my solution, so I’m much obliged to him posting his findings. Authenticating with the Twitter API: old vs new Acessing The Twitter API the old way: require ‘twitter’ httpauth = Twitter::HTTPAuth.new('my_account','my_secret_password') client = Twitter::Base.new(httpauth) client.update(‘Hurray!’) The OAuth way: require 'twitter' oauth = Twitter::OAuth.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY') oauth.authorize_from_access('123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis', 'fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh') client = Twitter::Base.new(oauth) client.update(‘Hurray!’) In the above case, ve4whatafuzzksaMQKjoI is the ‘consumer key’ (sometimes also referred to as ‘consumer token’) and KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY is the ‘consumer secret’. You’ll get these from Twitter when you register your app. 123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis is the ‘access token’ and fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh is the ‘access secret’. This combination gives the registered application access to your account. I’ll show you how to obtain these by following the steps below. (Basically you’ll need a bunch of keys and you’ll have to jump a bit through hoops to obtain them for your server/bot. ) How to get these keys 1. Surf to the twitter apps registration page go to http://dev.twitter.com/apps to register your app. Login with your twitter account. 2. Register your application Enter something for Application name, Description, website,… as I said: they make you jump through hoops. If you plan on using the API to post tweets, Your application name and website will be used in the ‘5 minutes ago via…’ line below your tweet. You could use the this to point to a page with info about your bot, or maybe it’s useful for SEO purposes. For application type I choose ‘browser’ and entered http://www.hadermann.be/callback as a ‘Callback URL’. This url returns a 404 error, which is ideal because after giving our account access to our ‘application’ (step 6), it will redirect to this url with an ‘oauth_token’ and ‘oauth_verifier’ in the url. We need to get these from the url. It doesn’t really matter what you enter here though, you could leave it blank because you need to explicitely specify it when generating a request token. You probably want read&write access so set this at ‘Default Access type’. 3. Get your consumer key and consumer secret On the next page, copy/paste your ‘consumer key’ and ‘consumer secret’. You’ll need these later on. You also need these as part of the authentication in your script later on: oauth = Twitter::OAuth.new([consumer key], [consumer secret]) 4. Obtain your request token run the following in IRB to obtain your ‘request token’ Replace my fake consumer key and consumer secret with the one you obtained in step 3. And use something else instead http://www.hadermann.be/callback: although this will only give a 404, you shouldn’t trust me. irb(main):001:0> require 'oauth' irb(main):002:0> c = OAuth::Consumer.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY', {:site => 'http://twitter.com'}) irb(main):003:0> request_token = c.get_request_token(:oauth_callback => 'http://www.hadermann.be/callback') irb(main):004:0> request_token.token => "UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1" This (UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1) is the request token: Copy/paste this token, you will need this next. 5. Authorize your application surf to https://api.twitter.com/oauth/authorize?oauth_token=[the above token], for example: https://api.twitter.com/oauth/authorize?oauth_token=UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1 This will bring you to the ‘An application would like to connect to your account’- screen on Twitter where you can grant access to the app you just registered. If you aren’t still logged in, you need to login first. Click ‘Allow’. Unless you don’t trust yourself. 6. Get your oauth_verifier from the redirected url Your browser will be redirected to your callback url, with an oauth_token and oauth_verifier parameter appended. You’ll need the oauth_verifier. In my case the browser redirected to: http://www.hadermann.be/callback?oauth_token=UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1&oauth_verifier=waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag Which returned a 404, giving me the chance to copy/paste my oauth_verifier: waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag 7. Request an access token Back to irb, use the oauth_verifier to request an access token, as follows: irb(main):005:0> at = request_token.get_access_token(:oauth_verifier => 'waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag') irb(main):006:0> at.params[:oauth_token] => "123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis" irb(main):007:0> at.params[:oauth_token_secret] => "fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh" We’re there! 123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis is the access token. fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh is the access secret. Try it! Try the following to post an update: require 'twitter' oauth = Twitter::OAuth.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY') oauth.authorize_from_access('123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis', 'fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh') client = Twitter::Base.new(oauth) client.update(‘Cowabunga!’) Now you can go to your twitter page and delete the tweet if you want to.

  Read the article

• SQL SERVER – How to See Active SQL Server Connections For Database

  - by Pinal Dave

  Another question received via email - “How do I I know which user is connected to my database with how many connection?” Here is the script which will give us answer to the question. SELECT DB_NAME(dbid) AS DBName, COUNT(dbid) AS NumberOfConnections, loginame FROM    sys.sysprocesses GROUP BY dbid, loginame ORDER BY DB_NAME(dbid) Here is the resultset: Reference: Pinal Dave (http://blog.SQLAuthority.com)Filed under: PostADay, SQL, SQL Authority, SQL DMV, SQL Query, SQL Server, SQL Tips and Tricks, T SQL

  Read the article

• Why can't I reinstall MySQL?

  - by Johannes Nielsen

  I've been looking all around the Internet for an answer but didn't find anything. I hope you can help me now. I have a server with MySQL. From one day to another, MySQL didn't let me enter with my root password anymore (accsess denied for user 'root'@'localhost' using password: 'YES'). So I tried two ways to reset the password: No.1: I typed: shell> /etc/init.d/mysqld stop To stop MySQL. Then I restarted it skipping the grant-tables: shell> mysqld_safe --skip-grant-tables So I was able to log in as root and change the password using: mysql> UPDATE mysql.user SET Password = PASSWORD('MyNewPassword') WHERE User = 'root'; FLUSH PRIVILEGES; I restarted MySQL and tried to log in as root with my new password - didn't work. So I tried the solution that's described here: http://dev.mysql.com/doc/refman/5.0/en/resetting-permissions.html (I don't want to post it here because this post is already pretty long). Didn't work either. Actually it made it worse, because since that day, every time I try to start MySQL, it doesn't even ask me for my password, but I get: shell> ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (111) Well, I've looked up what it means and found that my mysqld.sock is missing. I tried to create it using touch but MySQL can't start with that socket. Now I'm trying to reinstall MySQL but everytime I type in shell> apt-get --purge remove mysql-server mysql-common mysql-client In that or any other order or every one of those three alone, I get: shell> Reading package lists... Done shell> Building dependency tree shell> Reading state information... Done shell> Package mysql-client is not installed, so not removed shell> Package mysql-server is not installed, so not removed shell> You might want to run 'apt-get -f install' to correct these: shell> The following packages have unmet dependencies: shell> libmysqlclient18 : Depends: mysql-common (>= 5.5.28-0ubuntu0.12.04.2) but it is not going to be installed shell> libmysqlclient18:i386 : Depends: mysql-common:i386 (>= 5.5.28-0ubuntu0.12.04.2) shell> mysql-client-5.5 : Depends: mysql-common (>= 5.5.28-0ubuntu0.12.04.2) but it is not going to be installed shell> mysql-server-5.5 : PreDepends: mysql-common (>= 5.5.28-0ubuntu0.12.04.2) but it is not going to be installed shell> psa-firewall : Depends: plesk-core (>= 11.0.9) but it is not installable shell> Depends: mysql-server but it is not going to be installed shell> psa-spamassassin : Depends: plesk-core (>= 11.0.9) but it is not installable shell> psa-vpn : Depends: plesk-core (>= 11.0.9) but it is not installable shell> Depends: plesk-base (>= 11.0.9) but it is not installable shell> Depends: mysql-server but it is not going to be installed shell> E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). So I said to my self "let's just remove those files with depenencies, too" (that psa-stuff since plesk is virtual and can't be uninstalled)... Guess what happened: shell> Reading package lists... Done shell> Building dependency tree shell> Reading state information... Done shell> Package mysql-client is not installed, so not removed shell> Package mysql-server is not installed, so not removed shell> You might want to run 'apt-get -f install' to correct these: shell> The following packages have unmet dependencies: shell> libmysqlclient18 : Depends: mysql-common (>= 5.5.28-0ubuntu0.12.04.2) but it is not going to be installed shell> libmysqlclient18:i386 : Depends: mysql-common:i386 (>= 5.5.28-0ubuntu0.12.04.2) shell> mysql-client-5.5 : Depends: mysql-common (>= 5.5.28-0ubuntu0.12.04.2) but it is not going to be installed shell> mysql-server-5.5 : PreDepends: mysql-common (>= 5.5.28-0ubuntu0.12.04.2) but it is not going to be installed shell> E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). Of course I tried apt-get -f install, too many times even. What am I doing wrong? No matter, which other packages I include into apt-get --purge remove, I always get new dependencies. Do I have to delete every MySQL-related directory and file manually? Hope there's someone out there who can help me! Cheers! EDIT: After trying apt-get purge mysql-server mysql-common mysql-client libmysqlclient18 libmysqlclient18:i386 mysql-client-5.5 mysql-server-5.5 psa-firewall psa-spamassassin psa-vpn Reading package lists... Done Building dependency tree Reading state information... Done Package mysql-client is not installed, so not removed Package mysql-server is not installed, so not removed You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: libdbd-mysql-perl : Depends: libmysqlclient18 (>= 5.5.13-1) but it is not going to be installed libmyodbc : Depends: libmysqlclient18 (>= 5.5.13-1) but it is not going to be installed libqt4-sql-mysql:i386 : Depends: libmysqlclient18:i386 (>= 5.5.13-1) but it is not going to be installed php5-mysql : Depends: libmysqlclient18 (>= 5.5.13-1) but it is not going to be installed ruby-mysql : Depends: libmysqlclient18 (>= 5.5.13-1) but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). So I tried to remove all these and got: Building dependency tree Reading state information... Done Package mysql-client is not installed, so not removed Package mysql-server is not installed, so not removed You might want to run 'apt-get -f install' to correct these:qlclient18:i386 mysql The following packages have unmet dependencies: libmysql-ruby1.8 : Depends: ruby-mysql but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). And actually I think removing that file, too solved my problem :-S Next time I'll try everything before asking :D Thank you Eric for keeping me couraged to just go on removing :D

  Read the article

• Web 2.0 Extension for ASP.NET

  - by Visual WebGui

  ASP.NET is now much extended to support line of business and data centric applications, providing Web 2.0 rich user interfaces within a native web environment. New capabilities allowed by the Visual WebGui extension turn Visual Studio into a rapid development tool for the web, leveraging the wide set of ASP.NET web infrastructures runtime and extending its paradigms to support highly interactive applications. Taking advantage of the ASP.NET infrastructures Using the native ASP.NET ISAPI filter: aspnet_isapi...(read more)

  Read the article

< Previous Page | 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420  | Next Page >