Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 242/1359 | < Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >

• Hostapd - WLAN as AP

  - by BBK

  I'm trying to start hostapd but without success. I'm using Headless Ubuntu 11.10 oneiric 3.0.0-16-server x86_64. WLAN driver is rt2800usb and my wireless nic card TP-Link TL-WN727N supports AP mode as shows below: us0# ifconfig wlan0 wlan0 Link encap:Ethernet HWaddr 00:27:19:be:cd:b6 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) us0# lsusb Bus 003 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter us0# lshw -C network *-network:3 description: Wireless interface physical id: 4 bus info: usb@3:2 logical name: wlan0 serial: 00:27:19:be:cd:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.0.0-16-server firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn us0# hostapd /etc/hostapd/hostapd.conf Configuration file: /etc/hostapd/hostapd.conf Could not read interface wlan0 # The int flags: No such device nl80211 driver initialization failed. ELOOP: remaining socket: sock=4 eloop_data=0xd3e4a0 user_data=0xd3ecc0 handler=0x433880 ELOOP: remaining socket: sock=6 eloop_data=0xd411f0 user_data=(nil) handler=0x43cc10 us0# cat /etc/hostapd/hostapd.conf ssid=Home interface=wlan0 # The interface name of the card #driver=rt2800usb driver=nl80211 macaddr_acl=0 ieee80211n=1 channel=1 hw_mode=g auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=88888888 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP us0# iw list Wiphy phy0 Band 1: Capabilities: 0x172 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 1-stream Max AMSDU length: 7935 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-7, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (passive scanning, no IBSS) * 2472 MHz [13] (20.0 dBm) (passive scanning, no IBSS) * 2484 MHz [14] (20.0 dBm) (passive scanning, no IBSS) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * Unknown command (68) * Unknown command (55) * Unknown command (57) * Unknown command (59) * Unknown command (67) * set_wiphy_netns * Unknown command (65) * Unknown command (66) * connect * disconnect The question is: Why the hostapd not starting?

  Read the article

• Markdown, LaTeX combined in WYSIWYG editor. Is there any?

  - by om-nom-nom

  I really like the way markdown is implemented in SE bunch of sites, where I can easily write code blocks, performing formatting or even use latex on some of sites like writing $\pi$. I also like how this online editor looks and feels. But it's all online. Is there any offline WYSIWYG analogs of notepag or WMD in Ubuntu that optionally supports pdf as an output format? Both markdown and latex desired. I desire to simultaneously use Markdown and LaTeX. I'm planing to use an editor for writing some technical stuff with math, but it's annoying to be constantly in "LaTeX-mode". So it would be awesome to immerse in LaTeX when I need formulas and use markdown when I need to speak on natural language. UPD. Almost all answers was quite useful, but none of them answers directly on my question. I'll accept @N.N. answer as a most complete.

  Read the article

• Stuck on Ubuntu screen during installation of 12.10

  - by Rick de Groot

  From 12.04 I changed to win 8 consumer preview and now i want to go to 12.10, however i cant seem get past the Ubuntu loadingscreen( with the dots going from white to yellow etc.) it has taken more then an hour now and all my DVD drive does is speed up and slow down every 3 seconds. So i tried it again, but nothing changed im stuck on the same spot. what could cause this problem? And even better, how do i solve it?

  Read the article

• Nautilus is really slow

  - by david

  Nautilus used to be lightning fast.Now it's dead slow. I have tried upgrading the video card but that does not seem to be the problem. Also I found that there was a problem with the Dropbox uninstall, finally I replace it with pcmanfm which appears to be much faster but the down side is that I no longer have the gwibber social client and a lot of stuff don't work like they use to. Also I completely removed nautilus and couldn't even login to ubuntu to install again nautilus.How can I remove or repair nautilus, and use pcmanfm instead? I have a dell inspiron 1440 3gb ram / disk 300gb / Additionally, why does nautilus run fast when I run it as root? There are no USB devices attached to my computer. Thanks in advance

  Read the article

• Window decoration of emacs23 window on fluxbox is outside screen

  - by mit

  I am starting emacs remotely over an ssh connection. But on the emacs window I cannot find a way to resize or move it. There is no fluxbox title bar visible, and I guess the title bar is above the visible viewport, because emacs starts vertically with more height than the screen has. The lower border of the emacs window is also below the viewport border, so I cannot resize the window. I am starting emacs like this: emacs23 This is the emacs version: This is GNU Emacs 23.1.1 (x86_64-pc-linux-gnu, GTK+ Version 2.20.0) of 2010-03-29 on yellow, modified by Debian The remote system that runs emacs is 10.04 Lucid Lynx amd64. The local system is running 9.10 Karmic Koala 32 bit and Fluxbox 1.1.1-2

  Read the article

• USB external drive is not recognized by any OS, how to troubleshoot in Ubuntu?

  - by Breno

  First of all I would like to inform you that I saw a question similar to mine but the error was different, so here's my problem... I have an external HD samsung s2 model of 500GB and a day to day just stopped working, tried in other systems (windows and mac) however are not recognized. In the windows device manager when I insert the usb it states that the device in question are not working properly. Well, in the logs of my ubuntu 4.12 I see the following message when I insert my usb device in: [ 2967.560216] usb 7-2: new full-speed USB device number 2 using uhci_hcd [ 2967.680182] usb 7-2: device descriptor read/64, error -71 [ 2967.904176] usb 7-2: device descriptor read/64, error -71 [ 2968.120227] usb 7-2: new full-speed USB device number 3 using uhci_hcd [ 2968.240207] usb 7-2: device descriptor read/64, error -71 [ 2968.464063] usb 7-2: device descriptor read/64, error -71 [ 2968.680087] usb 7-2: new full-speed USB device number 4 using uhci_hcd [ 2969.092085] usb 7-2: device not accepting address 4, error -71 [ 2969.208155] usb 7-2: new full-speed USB device number 5 using uhci_hcd [ 2969.624076] usb 7-2: device not accepting address 5, error -71 [ 2969.624118] hub 7-0:1.0: unable to enumerate USB device on port 2 [ 4520.240340] usb 7-1: new full-speed USB device number 6 using uhci_hcd [ 4520.364079] usb 7-1: device descriptor read/64, error -71 [ 4520.588109] usb 7-1: device descriptor read/64, error -71 [ 4520.804140] usb 7-1: new full-speed USB device number 7 using uhci_hcd [ 4520.924136] usb 7-1: device descriptor read/64, error -71 [ 4521.148083] usb 7-1: device descriptor read/64, error -71 [ 4521.364105] usb 7-1: new full-speed USB device number 8 using uhci_hcd [ 4521.776237] usb 7-1: device not accepting address 8, error -71 [ 4521.888206] usb 7-1: new full-speed USB device number 9 using uhci_hcd [ 4522.296102] usb 7-1: device not accepting address 9, error -71 [ 4522.296150] hub 7-0:1.0: unable to enumerate USB device on port 1 [ 4749.036104] usb 7-2: new full-speed USB device number 10 using uhci_hcd [ 4749.156209] usb 7-2: device descriptor read/64, error -71 [ 4749.380215] usb 7-2: device descriptor read/64, error -71 [ 4749.596206] usb 7-2: new full-speed USB device number 11 using uhci_hcd [ 4749.716409] usb 7-2: device descriptor read/64, error -71 [ 4749.940110] usb 7-2: device descriptor read/64, error -71 [ 4750.156257] usb 7-2: new full-speed USB device number 12 using uhci_hcd [ 4750.572150] usb 7-2: device not accepting address 12, error -71 [ 4750.684215] usb 7-2: new full-speed USB device number 13 using uhci_hcd [ 4751.100182] usb 7-2: device not accepting address 13, error -71 [ 4751.100224] hub 7-0:1.0: unable to enumerate USB device on port 2 Here is my system: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 08ff:2810 AuthenTec, Inc. AES2810 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 00:1f.5 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 02:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba) 02:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) 02:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21) 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Does anyone have any clue what would be the problem?

  Read the article

• Failed to spawn test

  - by Lost

  Running a simple test in Ubuntu 12.04: sudo lxc-execute -n test /bin/bash -l debug -o outout Got error message: lxc-execute: failed to spawn 'test' cat outout: lxc-execute 1347053658.113 DEBUG lxc_start - sigchild handler set lxc-execute 1347053658.113 INFO lxc_start - 'test' is initialized lxc-execute 1347053658.366 DEBUG lxc_start - Dropping cap_sys_boot and watching utmp lxc-execute 1347053658.366 DEBUG lxc_cgroup - checking '/' (rootfs) lxc-execute 1347053658.366 DEBUG lxc_cgroup - checking '/sys' (sysfs) lxc-execute 1347053658.366 DEBUG lxc_cgroup - checking '/proc' (proc) lxc-execute 1347053658.366 DEBUG lxc_cgroup - checking '/dev' (devtmpfs) lxc-execute 1347053658.366 DEBUG lxc_cgroup - checking '/dev/pts' (devpts) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/run' (tmpfs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/' (ext3) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/sys/fs/fuse/connections' (fusectl) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/sys/kernel/debug' (debugfs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/sys/kernel/security' (securityfs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/run/lock' (tmpfs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/run/shm' (tmpfs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/run/rpc_pipefs' (rpc_pipefs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/scratch/WAMC-Simulation' (nfs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/share' (nfs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/proj/WAMC-Simulation' (nfs) lxc-execute 1347053658.367 DEBUG lxc_cgroup - checking '/users/bhu' (nfs) lxc-execute 1347053658.367 ERROR lxc_start - failed to spawn 'test' Run command: sudo lxc-checkconfig Kernel config /proc/config.gz not found, looking in other places... Found kernel config file /boot/config-2.6.38.7-1.0emulab --- Namespaces --- Namespaces: enabled Utsname namespace: enabled Ipc namespace: enabled Pid namespace: enabled User namespace: enabled Network namespace: enabled Multiple /dev/pts instances: enabled --- Control groups --- Cgroup: enabled Cgroup namespace: enabled Cgroup device: enabled Cgroup sched: enabled Cgroup cpu account: enabled Cgroup memory controller: enabled Cgroup cpuset: enabled --- Misc --- Veth pair device: enabled Macvlan: enabled Vlan: enabled File capabilities: enabled Note : Before booting a new kernel, you can check its configuration usage : CONFIG=/path/to/config /usr/bin/lxc-checkconfig What's the problem? Thanks a lot

  Read the article

• Bad 3D Performance in Ubuntu 12.04

  - by Pandem

  I already posted a question before but I didn't really get any advice/help. I'll be a bit more brief/general in hope it'll help. I have an MSI HD 7850 with the Catalyst 12.4 drivers installed. I've found that I'm having bad 3D performance for some reason but I'm not entirely sure what. I suspect it may just that the graphics card is new and AMD just need to work on their drivers but it would be nice to get advice and narrow the problem down so that I can be sure rather than wait for driver updates that may not even help. I ran gxlgears to give some general idea of how bad the performance is. At default size it is averaging around 2000 FPS. The command glxinfo confirms the renderer is using AMD Radeon HD 7800 Series with OpenGL version 4.2. Edits below: As asked for others: lspci -v output is here. fglrxinfo output is here xvinfo output is here glxinfo | grep rendering says yes for direct rendering. These confirmed that everything was configured correctly. Within Unity and Gnome Classic: glxgears had an FPS of around 2000 FPS fgl_glxgears had an FPS of around 544 FPS Within LDXE: glxgears had an FPS of around 4600 FPS fgl_glxgears had an FPS of around 1600 FPS In the end it was discovered that Compiz was causing a large performance decrease and solution was simply to change window manager for the time being. Thanks to TechZilla for all his help!

  Read the article

• Ubuntu stuck in low resolution after UNinstalling / disabling NVidia drivers

  - by Han Cnx

  Tried the Nvidia driver, installed using the Additional Drivers panel. Didn't like it much; the CPU seemed to overheat more and the brightness controls stopped working. Also selecting a second display is a pain using that horrible NVidia settings thing. So wanted to disabled it again.. problem is, UBuntu is then stuck in either 640x480 or 800x600 (second time I tried to install it back and then remove again). How can I get this back the way it was? The original Ubuntu drivers worked just fine, allowing me to run Unity and games properly. I tried a xserver-xorg reconfigure but this didn't do anything. (No xorg.conf file either). This is on a Lenovo Thinkpad T410i

  Read the article

• Removed Xserver driver. ubuntu doesnt start. what should i Do?

  - by user71576

  im new on ubuntu , i intalled it ( dual booted with windows 7) i was customizing it, but when i tried to run compiz it said that missing glx or something like that in the screen, i realized that the driver that i was not using wasnt the gefroce on so i went to nvidia downloaded the correct version for my graphic ( geforce gtm 525m) when y run the .run file it told me that i was using xserver and that i cant install this driver with the xserver installed. i search for information of how to remove or disable xserver i found one. in this web site --http://www.ubuntugeek.com/ubuntu-tiphow-to-removeinstall-and-reconfigure-xorg-without-reinstalling-ubuntu.html when i run the command , after that i tried to instal the geforce on, doesnt work so i remember windows that you must reboot after a driver unintallation or intallation so i reboot, them ubuntu doesnto load, it show the ubuntu whit the five dots like or 1-2 sec and them i get a black screen ( not the red-black of ubutntu ) so why i should do. i dont want to re install i dont have a cd and my usb is a little damaged so please if you could help me

  Read the article

• LAMP Stack Location

  - by Artem Moskalev

  I have installed the LAMP stack on Ubuntu 12.04 LTS using the tasksel command. I checked - it works. But I cant find the location of the installaton, I worked with WAMP - there you have a separate folder for Apache, for PHP and for mysql. Now I cant even find where to put the documents I create. Which folder is used to contain my web projects? How to start MySQL console and where to look for its installation directory? Which directories are PHP and Apache installed in? how to erase LAMP stack? I found out that some of the parts of the stack are installed in the root/var and root/etc directories: How can I install the whole LAMP stack in /home?

  Read the article

• ubuntu 12.10 installation failure

  - by Eidelmaim

  Here i am asking this question again because someone deemed it a duplicate to another topic which i over looked and NOTHING AT ALL in that topic pertained to my problem. If your going to close a topic believing it is a duplicate at least do somke reasearch into WHY you think its a duplicate and provide a like to a better source. How do i get past this installation username and password issue? I downloaded ubuntu 12.10 directly from Ubuntu.com and created a bootable USB with linuxlive. after loading the boot drive and ubuntu begins, it goes directly from the purple ubuntu startup screen directly to a black DOS like prompt asking for a ubuntu login. this is COMPLETLY before any installation -begins. i need some help with this. FYI : this is what it is saying after it goes to the login area in the DOS (Full black screen) like screen. Ubuntu 12.10 ubuntu tty1 ubuntu login: now i will provide a few images of the problem i am having. and because i DONT HAVE ANY OS on the computer BECAUSE ubuntu WONT go PAST this... i have to snap these pictuires with a cell phone and upload on another PC. these links are in chronological order from time of pressing power button to time i am presented with log in screen : image 1 image 2 can only post 2 links in messages... will post additional links in comments So, again... how do i get past this ? this is entireley before ubuntu is installed on my system. my PC specs... Homebuilt computer: Motherboard is a Asus Sabertooth x58 with a intel core i7 processor. Mushkin memory @ 12gbs. 4ea. Seagate 150gb hard drives. nvidia GTX 260 graphics card. i initially attempted to install to raid 5. failed. i broke down the raid and attempted to install to a single drive with all other drives disconnected from the PC. again, thanks in advanced for any assistance.

  Read the article

• How to make pulseaudio work again?

  - by Pawel M.

  I was having problems with sound (mono only output), so following advice from another askubuntu question I made some edits in /etc/pulse/default.pa After rebooting I had no sound at all. So I deleted /etc/pulse/default.pa entirely and tried another reboot. I did not backup the file (stupid, I know). How to come back to working config? edit: I tried: sudo apt-get remove pulseaudio (reboot) sudo apt-get install pulseaudio (reboot) It's still not working. The file /etc/pulse/default.pa is missing. Here's what pulseaudio and pacmd commands show: $ pulseaudio E: [pulseaudio] main.c: Daemon startup without any loaded modules, refusing to work. $ pacmd No PulseAudio daemon running, or not running as session daemon.

  Read the article

• Flash video doesn't work after upgrade to 11.10

  - by keekerdc

  I've found that after upgrading to 11.10 (32 bit), I can no longer watch streaming flash video on sites such as Ustream or Justin.tv. I've spent the last several hours installing this package and uninstalling that package, and purging everything flash-related and starting over, to no avail. I was curious if anybody else has run into similar issues and found a fix. I'm running an NVIDIA card, and I've tried both sets of drivers available.

  Read the article

• Not able to connect huawei ec1561

  - by Nixon Babu

  I have a huawei ec1561 broadband data card, ISP-MTS India. I am not able to connect internet through it. while connecting it via network manager it says "You are registered with home network" and again "Modem network disconnected" . i think it is detected as a modem but not connecting properly. Any help please? I'm hitting this rock with my head more than a month... when I tried installing the driver that came with the device it finally says "Installing NDIS driver failed". I can post further information if anybody helps

  Read the article

• "/etc/apache2/mods-enabled/proxy_html.load: Cannot load /usr/lib/libxml2.so.2 into server" error with Apache mod-proxy

  - by hhh

  The command $ sudo apt-get install libapache2-mod-proxy-html and then $sudo service apache2 restart fires: apache2: Syntax error on line 210 of /etc/apache2/apache2.conf: Syntax error on line 1 of /etc/apache2/mods-enabled/proxy_html.load: Cannot load /usr/lib/libxml2.so.2 into server: /usr/lib/libxml2.so.2: cannot open shared object file: No such file or directory Action 'configtest' failed. I am using X220 laptop. Perhaps related thing but ?AMD here. Perhaps some repeating bug in Ubuntu, again. How to fix this? Any patch yet for Ubuntu?

  Read the article

• Accessing host LVM partition from Windows XP through Virt.manager 0.8.5 / Qemu / KVM

  - by Nico de Smidt

  Hi, requested use case is having a Windows XP SP3 guest running in 64bit Ubuntu. (Linux pcs 2.6.35-22-server #35-Ubuntu SMP Sat Oct 16 22:02:33 UTC 2010 x86_64 GNU/Linux) I want this guest to access an LVM LV on the Ubuntu disk. I've setup the following LVM config: --- Logical volume --- LV Name /dev/storage/sdc1 VG Name storage LV UUID Zg5IMC-OlqB-prL5-fgg4-3A9A-OgKP-oZ0QkJ LV Write Access read/write LV Status available # open 0 LV Size 1.01 GiB Current LE 259 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 251:3 -- 1) I've setup a storage pool for /dev/storage 2) I've mkfs.vfat /dev/storage/sdc1 3) and made a virtual IDE disk in the virt-manager setup for the guest. Target device: IDE Disk 2 Source path: /dev/storage/sdc1 -- Now when running XP (guest) Windows sees a new disk in Disk Manager and want's to install a partition on it, since it believes the drive is empty. After formatting from within Windows I can put data on the new disk volume. -- Back in Ubuntu however I cannot access this this any more since it created a partition within an LVM Logical Volume. Running fdisk -l shows the following: root@pcs:/media# fdisk -l /dev/storage/sdc1 Disk /dev/storage/sdc1: 1086 MB, 1086324736 bytes 32 heads, 63 sectors/track, 1052 cylinders Units = cylinders of 2016 * 512 = 1032192 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x8d72e4f4 Device Boot Start End Blocks Id System /dev/storage/sdc1p1 1 1050 1058368+ c W95 FAT32 (LBA) -- which seems fine to me, but when trying to mount /dev/storage/sdc1p1 I get the following error: mount /dev/storage/sdc1p1 /media/xp mount: special device /dev/storage/sdc1p1 does not exist which makes sense since in lvdisplay sdc1p1 does not exist Main question: I want to mount the vfat partition in both Ubuntu and XP What am I missing here????? regards, and thanks for your consideration. Nico

  Read the article

• While installing Ubuntu from Ubuntu Desktop (from USB)

  - by Andres

  I downloaded the Ubuntu Software to create a USB to install Ubuntu. I rebooted my PC (Windows 7), in wich i did a partition (:E) just for Ubuntu. But when i start the installer, it says there's no other OS in my computer, and doesn't give me the option to install it in :E, just the option to format the WHOLE hard drive and install it there. What can i do? Also, i tried Wubi before, but it had an error with "wubildr.mbr"

  Read the article

• Atheros AR9485 wireless card doesn't work in an ASUS K53E

  - by John

  I just installed Ubuntu 11.10 32-bit version in dual boot mode on an ASUS K53. Every thing seems to work fine except for the wireless. The wireless works on Windows 7. Ubuntu finds the wireless card, but it does not appear to be turned on. The only physical means of turning on the card is the FN-F2 key combo. That works on Windows, but not in Ubuntu. I've looked in the forums for a solution and I'm not quite sure what to do. I've gathered the following information: jdwbmc@Spatha:~$ cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" Linux Spatha 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:50:42 UTC 2011 i686 i686 i386 GNU/Linux jdwbmc@Spatha:~$ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:1186] Kernel driver in use: ath9k -- 04:00.0 Ethernet controller [0200]: Atheros Communications AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) Subsystem: ASUSTeK Computer Inc. Device [1043:1851] Kernel driver in use: atl1c jdwbmc@Spatha:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 058f:a014 Alcor Micro Corp. jdwbmc@Spatha:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff jdwbmc@Spatha:~$ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no jdwbmc@Spatha:~$ lsmod Module Size Used by parport_pc 32114 0 ppdev 12849 0 snd_hda_codec_hdmi 31426 1 bnep 17923 2 rfcomm 38408 0 bluetooth 148839 10 bnep,rfcomm snd_hda_codec_realtek 254125 1 binfmt_misc 17292 1 joydev 17393 0 asus_nb_wmi 12469 0 asus_wmi 19333 1 asus_nb_wmi sparse_keymap 13658 1 asus_wmi uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 24262 2 snd_hda_codec 91754 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80468 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 wmi 18744 1 asus_wmi snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event arc4 12473 2 i915 505108 3 snd_timer 28932 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq ath9k 112711 0 psmouse 73673 0 serio_raw 12990 0 mac80211 272785 1 ath9k drm_kms_helper 32889 1 i915 ath9k_common 13599 1 ath9k drm 192226 4 i915,drm_kms_helper ath9k_hw 293893 2 ath9k,ath9k_common ath 19387 2 ath9k,ath9k_hw cfg80211 172392 3 ath9k,mac80211,ath snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,s nd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd snd_page_alloc 14115 2 snd_hda_intel,snd_pcm mei 36466 0 i2c_algo_bit 13199 1 i915 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 3 libahci 25727 1 ahci atl1c 36638 0 xhci_hcd 72915 0 jdwbmc@Spatha:/var/lib/NetworkManager$ cat NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true jdwbmc@Spatha:~$ lspci -nn | grep 0280 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Any help would be appreciated. Thanks.

  Read the article

• Second monitor not detected

  - by configurator

  Note: I've seen this question quite a lot, but in all the cases I could find with answers, the answer was either "I don't know" or "use nvidia-settings (which is irrelevant to me)." I'm using Intel Sandybridge Desktop graphics, with a P8H61-M LE motherboard. How do I get Ubuntu to detect my second monitor? Clicking "Detect Displays" here doesn't do anything. Here's some system info: $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) $ uname -a Linux clyde 3.5.0-13-generic #13-Ubuntu SMP Tue Aug 28 08:31:47 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux $ hardinfo [copied from the UI] -Display- Resolution : 1920x1080 pixels Vendor : The X.Org Foundation Version : 1.12.3 -Monitors- Monitor 0 : 1920x1080 pixels -Extensions- BIG-REQUESTS Composite DAMAGE DOUBLE-BUFFER DPMS DRI2 GLX Generic Event Extension MIT-SCREEN-SAVER MIT-SHM RANDR RECORD RENDER SECURITY SGI-GLX SHAPE SYNC X-Resource XC-MISC XFIXES XFree86-DGA XFree86-VidModeExtension XINERAMA XInputExtension XKEYBOARD XTEST XVideo -OpenGL- Vendor : Intel Open Source Technology Center Renderer : Mesa DRI Intel(R) Sandybridge Desktop Version : 3.0 Mesa 8.1-devel Direct Rendering : Yes I've tried upgrading everything from ppa:xorg-edgers/ppa and ppa:glasen/intel-driver. I've also installed various tools I've found in other threads (e.g. hardinfo) but they weren't really helpful to me as I don't know what to make of the data. How do I get Ubuntu to detect my second monitor?

  Read the article

• Error splicing file: Input/output error with a USB SD/HC card reader [closed]

  - by PirateRussell

  I recently got a new Droid Bionic, and it has the SD/HC card. Today, I got a new USB card reader that reads the HC format. When I plug it into my Linux Mint 11 (katya), Gnome 32-bit computer, I get this error every I try to copy or move any file off of the card onto my desktop: Error splicing file: Input/output error I don't have the problem on a Windows Vista computer. Any ideas??? Thanks in advance...

  Read the article

• Unable to install libcairo2:i386 on ubutu 12.10 X86_64

  - by user63726

  I get the following error. I think it is a bug. Is there a workaround? There is mismatch between the 32 and 64 bit version of this package. apt-get install libcairo2:i386 Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: libatk-wrapper-java-jni : Depends: libgtk2.0-0 (= 2.12.0) but it is not going to be installed Depends: libatk-wrapper-java (= 0.30.4-0ubuntu4) but it is not going to be installed E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages.

  Read the article

• Cannot run update due to a dpkg error with burg-theme-minimal-sir

  - by boywithaxe

  I cannot run an update or indeed run $: apt-get remove due to a dpkg error with a package that's a part of super-boot-manager. Running an update returns: dpkg: error processing burg-theme-minimal-sir (--configure): subprocess installed post-installation script returned error exit status 1 I tried removing this package alone, with the same error, also trying to remove super-boot-manager returns: (Reading database ... 225474 files and directories currently installed.) Removing burg-theme-minimal-sir ... Generating burg.cfg ... /usr/sbin/burg-probe: error: cannot stat `/boot/burg/locale'. No path or device is specified. Try `/usr/sbin/burg-probe --help' for more information. dpkg: error processing burg-theme-minimal-sir (--remove): subprocess installed post-removal script returned error exit status 1 No apport report written because MaxReports is reached already Removing super-boot-manager ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Errors were encountered while processing: burg-theme-minimal-sir E: Sub-process /usr/bin/dpkg returned an error code (1) I'm sort of stuck now and Google has failed me. Has anyone encountered this problem before? Or does anyone know a way for fixing this?

  Read the article

• How to fix sound in wolfenstein Enemy Territory

  - by GrizzLy

  I installed wolf:et, and i cant get sound to work. Everything that i have installed is in default paths, i had 10.4 and then upgraded to 10.10 via software update gui. I had sound working in 10.04 with method under 2. I have tried following killall esd; et; esd with that i get ------- sound initialization ------- /dev/adsp: No such file or directory Could not open /dev/adsp ------------------------------------ sudo -i echo "et.x86 0 0 direct" /proc/asound/card0/pcm0p/oss echo "et.x86 0 0 disable" /proc/asound/card0/pcm0c/oss exit with that i get bash: /proc/asound/card0/pcm0p/oss: No such file or directory and indeed i do not have that, i have only sub0 and sub1 in pcm0p I have tried running et with et-sdl-sound script, but with that i get this output in console http://pastebin.com/J7gRU1uh I have probably messed up sdl libraries, could not get sound to work, so downloaded new from debian package site and installed them. Tried setting SDL_AUDIODRIVER="pulse" in et-sdl-sound, looks like i am getting same error as in method 3. pasuspender -- et +set s_alsa_pcm plughw:0 gives me ------- sound initialization ------- /dev/adsp: No such file or directory Could not open /dev/adsp _------------------------------------ Misc: @Oli: i do not know if i am running pulse or esd, how can i check that?

  Read the article

• Ubuntu 13.10 installed and worked, but now not working

  - by San

  I have a HP G7000 laptop. I updated/upgraded from 13.04 to 13.10, after the software updater recommended I upgrade. I have duel booting system with Windows Vista. The system was working for the past two days, but I start getting the errors below, after selecting Ubuntu in Grub Menu on startup and at the splash screen it says "Press S to Skip or M for manual configuration" Pressing S gives a black screen and m takes you the errors below. Windows boots and works fine after selection in the Grub Menu. [ 15.235703] EXT3-fs (sda5): error: unrecognized mount option "discard" or missing value. [ 16.788072] [drm:intel_pipe_config_compare] *ERROR* mismatch in adjusted_mode flags [expected 2, found 0] [ 20.860071] [drm:intel_pipe_config_compare] *ERROR* mismatch in adjusted_mode flags [expected 2, found 0] [ 20.980076] [drm:intel_pipe_config_compare] *ERROR* mismatch in adjusted_mode flags [expected 2, found 0] Root filesystem Check failed root@simamhar:~# Tried boot-repair using the LiveCD method, no luck. System still gives above error. (you can view the boot-repair log here http://paste.ubuntu.com/6287287) When I use the liveCD for 13.04 or 13.10 however, my hard disk is recognized and I can read the files. Why is it that the installation on the hard disk has stopped working and does not recognize my / ? What do the above errors mean and how can i solve them? There was no power failure before, during or after the update/upgrade process from 13.04 to 13.10. I now would like to go back to 13.04 without reinstalling afresh? Any help will be appreciated. Thanks.

  Read the article

< Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >