Search Results

Search found 11685 results on 468 pages for 'intel core i5'.

Page 242/468 | < Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • The bottlenecks of any computer, what to look for?

    - by WebDevHobo
    Whether it is a laptop or a desktop, any computer is made up of several pieces of hardware that communicate with each other. Sending data back and forth to ensure that the user gets the desired results. I have seen some theoretical stuff on computers & hardware, but I wonder how it all comes together. CPU RAM Graphics Card L1 CACHE L2 CACHE L3 CACHE FSB ... And all other things. Which is the biggest bottle neck? Why would a person not want/need a big value in one of those categories in certain situations? P.S.: when reading the specs of the i5 750 processor, I came across this description: In place of the FSB, one or more high speed, point-to-point buses called Quick Path Interconnect (QPI) are used, formerly known as Common Serial Interconnect Bus or CSI. QPI features higher bandwidth than the traditional FSB and is better suited to system scaling. What is this, and how does it compare to FSB? EDIT: I am not planning to buy a computer at all. The goal of this question is to understand the internal relation of various hardware pieces, their specific functions and how they work together. For instance, I have heard to a somewhat higher-than-usual amount of L2/L3 Cache can help speed up your computer. What's up with saying that? Also I forgot to mention Hard-disk RPM.

    Read the article

  • ln -s not working under /mnt/

    - by Yaniv
    Hi all I'm following this tutorial to set up a LAMP stack on EC2 with persistent storage on EBS. It all works well when doing it step by step. But in case you want to mount your EBS under /mnt instead of under the root directory the ln -s commands won't work! I tried: ln -s /mnt/ebs1/httpd /etc and: ln -s /mnt/ebs1/httpd /etc/httpd Is there a difference when linking to a file on a device that is mounted under /mnt? (working on fedora core 8)

    Read the article

  • Running Hermes Anti-Spam Proxy Alongside Exchange 2003

    - by JohnyD
    I'm looking to implement an anti-spam solution to pre-process email destined for my Exchange 2003 server. I am interested in trying out the Hermes Anti-Spam Proxy product (the price is right) and was wondering if anyone has had any experience in running this alongside their Exchange installation (same physical box). The server is a Win2K3 box running a single core P4 D 930 @ 3GHz with 3 gigs of memory. Thank you.

    Read the article

  • Are there any advantages to using windows 7 ultimate? I can't tell the diference

    - by Jack Dawson
    I just upgraded my new desktop which came installed with Windows 7 Home Premium 64 bit with a copy of Windows 7 Ultimate 64 bit and so far I have not noticed any difference in performance. Even my Windows Experience Index number is the same 5.5 that it was before the upgrade. So what's the point, are there any performance advantages that I'm not seeing? Additional Info My system hardware specs: AMD quad core 2.6 GHZ 1 TB 4200 RPM HDD 8 GB DDR2 RAM ATI Radeon HD 4650 w/ 1GB dedicated video memory

    Read the article

  • Change Laptop Wireless Card?

    - by Craig
    I have just bought a new Samsung RV511 Laptop (the i5 Version). Anyway it comes installed with a Broadcom Wifi Card, I have a Super Atheros Mini Wifi Card that I would like to swap for the Broadcom one. I use Atheros for security auditing purposes in Linux that the Broadcom one is not good for. Trouble is I have never got to the barebones of a laptop, although I am a Custom PC Builder, laptops i generally have no concern for. Take a look at this picture, I took one back panel off to reveal some of the components: I believe the Wireless Card is where I marked the arrow pointing too. That little white square thing appears to be a sticker of the Wifi card, it says WLAN. How can I access it to swap it with my Atheros one. Do I need to remove all the outermost screws? There are screws located to the right of where I scribbled in Yellow and next to the HDD, do I just remove those? I dont want to destroy the machine, only just got it today. Appreciate some help thanks.

    Read the article

  • Best way to handle PHP sessions across Apache vhost wildcard domains

    - by joshholat
    I'm currently running a site that allows users to use custom domains (i.e. so instead of mysite.com/myaccount, they could have myaccount.com). They just change the A record of their domain and we then use a wildcard vhost on Apache to catch the requests from the custom domains. The setup is basically as seen below. The first vhost catches the mysite.com/myaccount requests and the second would be used for myaccount.com. As you can see, they have the exact same path and php cookie_domain. I've noticed some weird behavior surrounding the line below "#The line below me". When active, the custom domains get a new session_id every page load (that isn't the same as the non-custom domain session). However, when I comment that line out, the user keeps the same session_id on each page load, but that session_id is not the same as the one they'd see on a non-custom domain site either despite being completely on the same server. There is a sort of "hack" workaround involving redirecting the user to mysite.com/myaccount, getting the session ID, redirecting back to myaccount.com, and then using that ID on the myaccount.com. But that can get kind of messy (i.e. if the user logs out of mysite.com/myaccount, how does myaccount.com know?). For what it's worth, I'm using a database to manage the sessions (i.e. so there's no issues with being on different servers, etc, but that's irrelevant since we only use one server to handle all requests currently anyways). I'm fairly certain it is related to some sort of CSRF browser protection thing, but shouldn't it be smart enough to know it's on the same server? Note: These are subdomains, they're separate domains entirely (but on the same server). <VirtualHost *:80> DocumentRoot "/opt/local/www/mysite.com" ServerName mysite.local ErrorLog "/opt/local/apache2/logs/mysite.com-error.log" CustomLog "/opt/local/apache2/logs/mysite.com-access.log" common <Directory "/opt/local/www/mysite.com"> AllowOverride All #php_value session.save_path "/opt/local/www/mysite.com/sessions" php_value session.cookie_domain "mysite.local" php_value auto_prepend_file "/opt/local/www/mysite.com/core.php" </Directory> </VirtualHost> #Wildcard (custom domain) vhost <VirtualHost *:80> DocumentRoot "/opt/local/www/mysite.com" ServerName default ServerAlias * ErrorLog "/opt/local/apache2/logs/mysite.com-error.log" CustomLog "/opt/local/apache2/logs/mysite.com-access.log" common <Directory "/opt/local/www/mysite.com"> AllowOverride All #php_value session.save_path "/opt/local/www/mysite.com/sessions" # The line below me php_value session.cookie_domain "mysite.local" php_value auto_prepend_file "/opt/local/www/mysite.com/core.php" </Directory> </VirtualHost>

    Read the article

  • Building a PC for Work and play? [closed]

    - by Derek Organ
    Ok, Its been a long time since I build my own PC so I'm looking to get back into it again and build a new one. First off budget is about €800 excluding the monitor and windows 7 licence and mouse. (just bought a new g500) I plan on using my computer for work, lots of applications open at once but none particularly excessive (photoshop being the most demanding, mostly coding tools) I also use it for some gaming, e.g. COD, Starcraft etc. One thing I do want to do eventually is get a really good monitor with hight resolution and maybe 27" so the graphics card needs to be able to make best use of that. So a few questions 1) Is the bottle neck in performance mostly still the harddrives? 2) Aren't most processors e.g. i5 etc even i3 so far a head of other bottlenecks it makes litte difference the higher you go. Isn't the Graphics card dealing with heavy graphics so what really slows because of a slow CPU? So from this my thinking is to get a SSD drive as my primary drive for OS etc and have loads of memory e.g. 6-8GB and a decent mid level graphics card? It doesn't seem at my level worth spending much on CPU and any other parts really. I basic parts off the top of my head Case, Motherboard CPU SSD Drive SATA Drive Power Supply Memory Cooling (fan?) Graphics Card Network Card Keyboard DVD drive Mouse Windows Monitor Am I missing anything? Any helpful tips or general education much appreciated. Thanks, Derek

    Read the article

  • Planning trunk capacity for multiple GbE switches

    - by wuckachucka
    Without measuring throughput (it's at the top of the list; this is just theoretical), I want to know the most standard method for trunking VLANs on multiple Gigabit (GbE) switches to a core Layer 3 GbE switch. Say you have three VLANs: VLAN10 (10.0.0.0/24) Servers: your typical Windows DC/file server, Exchange, and an Accounting/SQL server. VLAN20: (10.0.1.0/24) Sales: needs access to everything on VLAN10; doesn't need access to VLAN30 and vice-versa. VLAN20: (10.0.1.0/24) Support: needs access to everything on VLAN10; doesn't need access to VLAN20 and vice-versa. Here's how I think this should work in my head: Switch #1: Ports 2-20 are assigned to VLAN20; all the Sales workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #1. Switch #2: Ports 2-20 are assigned to VLAN30; all the Support workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #2. Core L3 switch: Ports 2-10 are assigned to VLAN10; all three servers are connected here. With a standard 10/100 x 24 switch, it'll usually come with one or two 1 GbE uplink ports; carrying over this logic to a 10/100/1000 x 24, the "optional" 10 GbE combo ports that most higher-end switches can get shouldn't really be an option. Keep in mind I haven't tested anything yet, I'm primarily moving in this direction for growth (don't want to buy 10/100 switches and have to replace those within a couple of years) and security (being able to control access between VLANs with L3 routing/packet filtering ACLs). Does this sound right? Do I really need the 10 GbE ports? It seems very non-standard and expensive, but it "feels" right when you think about 40 or 50 workstations trunking up to the L3 switch over 1 GbE standard ports. If say 20 workstations want to download a 10 GB image from the servers concurrently, wouldn't the trunk be the bottleneck? At least if the trunk was 10 GbE, you'd have 10x1GbE nodes being able to reach their theoretical max. What about switch stacking? Some of the D-Links I've been looking at have HDMI interfaces for stacking. As far as I know, stacking two switches creates one logical switch, but is this just for management I/O or does the switches use the (assuming it's HDMI 1.3) 10.2 Gbps for carrying data back and forth?

    Read the article

  • Dual Monitor setup issues between laptop and external led monitor

    - by Julian
    I have two challenges. Monitor will not connect to laptop through HDMI Watching HD video content causes the laptop to sometimes turn off expecially when I'm streaming from tekzilla.com Setup. I got my new HP 2311x LED LCD monitor this week and I have it running as the main monitor extended by the 15 inch screen on my Dell Studio 1558. Right now I have to connect the external monitor through VGA. For the HDMI connection issue. I suspect that either the appropriate drivers are not installed because I don't see any hdmi device in the device manager. I've checked and I don't see any hdmi specific drivers listed online. For the shut down issue, I suspect the laptop might be overheating. Not sure why it would. It never did that while I watched movies on my laptop's default screen. My Laptop Configuration: 15" led lcd screen at 1366 x 768 intel i5 processor integrated graphics card 4 GB DDR3 RAM 500 GB hard drive I've tried everything from switching the source on my monitor to hdmi to start up combinations and nothing has worked. What could be the issue and how do I solve it?

    Read the article

  • Cygwin unable to compile

    - by christine
    I just downloaded Cygwin, I've never used it before cause I've always used putty. Cygwin is not letting me compile; I can see the files but it just doesn't let me compile and I do not understand why, am I doing something wrong? This is what's going on: Christine@Christine-PC ~ $ ls 8.6.c a.b.c a.c.c core new 2.txt test.c 9.13.c a.c a.out days.c new2.c test.txt Christine@Christine-PC ~ $ gcc a.c.c -bash: gcc: command not found

    Read the article

  • Force10 layer 3 switches

    - by ALQ
    We've been running Cisco and dell layer 3 switches. The former are expensive and reliable, the latter a lot cheaper and fraught with issues. Anyone has positive experience with the core Force10 switches (and edge switches as well)?

    Read the article

  • Laptop shuts down randomly without warning

    - by Robert P.
    My Asus Zenbook UX32V turns off randomly when I'm working on it. This happens both when the computer is recently turned on (5 minutes), and after being on for several days. I'm not running any heavy software The laptop is not heating The fan is not working on the maximum capacity (it's not heating) It happens when the laptop is lying still on the table It is no warning, it simply goes black It happens both when charging and on battery My guess is that it suddenly lose power somehow. What puzzles me is that I can flip the laptop upside down, sideways, shake it, etc. without it shutting off. This makes me think it's not something that's loose causing occasional short-circuits. I realize that the laptop probably doesn't like flipping and shaking, but it was the best way I could troubleshoot. I rarely turn the computer off, only have it in hibernate or sleep mode (most often hibernate). I've never experienced that the laptop is off when I wake it up from sleep mode. I've had the problem for a few months and it happens 2-8 times a week. Specs: Asus Zenbook UX32V Windows 8.1 (it happened in Windows 8.0 too) Intel i5-3317U CPU @ 1.70GHz The laptop is approx 1.5 years, but it has a small dent on one of the sides that probably voids the warranty. The dent has been there since week one and I don't think it's related to the problems I'm having now. Does anyone have a clue what might cause this, and how it might be fixed? I've read all other questions (some of which are listed below) that seem related to my issue, but none report the same behavior as I'm experiencing. Most report heavy games, heating etc. Asus N53J Laptop randomly shuts down Laptop is randomly shutting off Computer shuts down without warning My laptop acer aspire 5720 suddenly turn off randomly Computer randomly shutting down Windows 8.1 randomly shuts self down ASUS K55VM Laptop unexpectedly shuts down

    Read the article

  • Adding an assembly to the GAC

    - by Cyclone
    Somehow my GAC got messed up, System.Core.dll was unregistered or something. I don't have the win7 sdk so I can't just use gacutil. Is there some way I can add the single assembly to the gac? Or some way to download JUST gacutil? Is the GAC stored in the registry? If so, where? Thanks for the help, this is a pretty ugly bug.

    Read the article

  • Can't get virtual desktops to show up on RDWeb for Server 2012 R2

    - by Scott Chamberlain
    I built a test lab using the Windows Server 2012 R2 Preview. The initial test lab has the following configuration (I have replaced our name with "OurCompanyName" because I would like it if Google searches for our name did not cause people to come to this site, please do the same in any responses) Physical hardware running Windows Server 2012 R2 Preview full GUI, acting as Hyper-V host (joined to the test domain as testVwHost.testVw.OurCompanyName.com) with the following VM's running on it VM running 2012 R2 Core acting as domain controller for the forest testVw.OurCompanyName.com (testDC.testVw.OurCompanyName.com) VM running 2012 R2 Core with nothing running on it joined to the test domain as testIIS.testVw.OurCompanyName.com A clean install of Windows 7, all that was done to it was all windows updates where loaded and sysprep /generalize /oobe /shutdown /mode:vm was run on it A clean install of Windows 8, all that was done to it was all windows updates where loaded and sysprep /generalize /oobe /shutdown /mode:vm was run on it I then ran "Add Roles and Features" from testVwHost and chose the "Remote Desktop Services Installation", "Standard Deployment", "Virtual machine-based desktop deployment". I choose testIIS for the roles "RD Connection Broker" and "RD Web Access" and testVwHost as "RD Virtualization Host" The Install of the roles went fine, I then went to Remote Desktop Services in server manager and wet to setup Deployment Properties. I set the certificate for all 3 roles to our certificate signed by a CA for *.OurCompanyName.com. I then created a new Virtual Desktop Collection for Windows 7 and Windows 8 and both where created without issue. On the Windows 7 pool I added RemoteApp to launch WordPad, For windows 8 I did not add any RemoteApp programs. Everything now appears to be fine from a setup perspective however if I go to https://testIIS.testVw.OurCompanyName.com/RDWeb and log in as the use Administrator (or any orher user) I don't see the virtual desktops I created nor the RemoteApp publishing of WordPad. I tried adding a licensing server, using testDC as the server but that made no difference. What step did I miss in setting this up that is causing this not to show up on RDWeb? If any additional information is needed pleas let me know. I have tried every possible thing I can think of and I am just groping around in the dark now. The virtual machines running on testVwHost The configuration screen for RD Services The Windows 7 Pool The Windows 8 Pool This is logged in as testVw\Administrator

    Read the article

  • PHP wamp server error

    - by user38453
    I get this error when i click phpmyadmin.I m using vistaa.I uninstall ed skype.I deleted IIS and it is in my recycle bin, When,i click localhost,i get iis page.How do,i make this apache server to work.Below,is the error that comes Server Error in Application "DEFAULT WEB SITE" Internet Information Services 7.0 Error Summary HTTP Error 404.0 - Not Found The resource you are looking for has been removed, had its name changed, or is temporarily unavailable. Detailed Error Information Module IIS Web Core Notification MapRequestHandler Handler StaticFile Error Code 0x80070002 Requested URL http://localhost:80/phpmyadmin/ Physical Path C:\inetpub\wwwroot\phpmyadmin\ Logon Method Anonymous Logon User Anonymous

    Read the article

  • Intermittent lockups, unable to diagnose in over a year

    - by Magsol
    Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

    Read the article

  • Chrome browser completely messing with network?

    - by kiasecto
    I have a bizare problem with Google Chrome on a intel core i5 running windows 7 32bit. Whenever chrome is installed, access to other computers in the home group becomes really slow - such as opening shares. Its becomes really slow to resolve windows names. Something goes hay-wire with the local network - pining local machines which is usually 0mS pings I get random timeouts and random successes. Whenever I try to load a local address inside of chrome (including localhost, 192.168.0.1 etc) - it always says something in the status bar about resolving proxy and times out after about 5 seconds, then seems to work fine. If I go to settings inside of chrome, it just brings up the internet explorer connection settings, where I have not set any proxy settings. One I uninstall chrome, all these problems go away. Network shares and name resolvings work instantly, pings to any machines never have a problem. Localhost and other network IP address work fine in all other browsers. Anyone heard of this problem before and know what it might be? I even tried re-installing winodws 7 and the problem came straight back when chrome was loaded on again.

    Read the article

  • Best way to provide redundant switching/links to server

    - by Myles Gray
    We have 3x ESX hosts and 2x SANS that we wish to move to a redundant 10G networking infrastructure. We have 4x Dell PowerConnect 8024F's to provide our backbone and are configured as so (only core switches relevant to this question): So the questions are: 1) Do the interconnects between the 4x 8024F's need to be LAG'd or just STP'd 2) As the NICs on the servers are split across 2 switches, does any special configuration need to be done here or on the switches? 3) If a link or switch fails will the switches automatically find a new path to the Server/SAN?

    Read the article

  • Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

    - by Software Monkey
    I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

    Read the article

  • SQL Server 2012 Read-Only Replica physical requirements

    - by Ddono25
    We are going to be setting up two replicas of our DataMart and related databases, and our plan includes using Hyper-V VM's to handle the load. When creating the VM's, we cannot find specific requirements or recommendations for RAM/CPU power for read-only replicas. Our current Primary DataMart setup has 64GB RAM and Two Quad-Core procs, which so far has been adequate for our usage. What should be the server setup for replicas and SQL Server to adequately support the read-only usage?

    Read the article

< Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >