Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 242/600 | < Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249 | Next Page >

Cisco ASA Site-to-Site VPN Dropping

- by ScottAdair

I have three sites, Toronto (1.1.1.1), Mississauga (2.2.2.2) and San Francisco (3.3.3.3). All three sites have ASA 5520. All the sites are connected together with two site-to-site VPN links between each other location. My issue is that the tunnel between Toronto and San Francisco is very unstable, dropping every 40 min to 60 mins. The tunnel between Toronto and Mississauga (which is configured in the same manner) is fine with no drops. I also noticed that my pings with drop but the ASA thinks that the tunnel is still up and running. Here is the configuration of the tunnel. Toronto (1.1.1.1) crypto map Outside_map 1 match address Outside_cryptomap crypto map Outside_map 1 set peer 3.3.3.3 crypto map Outside_map 1 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_3.3.3.3 internal group-policy GroupPolicy_3.3.3.3 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 3.3.3.3 type ipsec-l2l tunnel-group 3.3.3.3 general-attributes default-group-policy GroupPolicy_3.3.3.3 tunnel-group 3.3.3.3 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** San Francisco (3.3.3.3) crypto map Outside_map0 2 match address Outside_cryptomap_1 crypto map Outside_map0 2 set peer 1.1.1.1 crypto map Outside_map0 2 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map0 2 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_1.1.1.1 internal group-policy GroupPolicy_1.1.1.1 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 general-attributes default-group-policy GroupPolicy_1.1.1.1 tunnel-group 1.1.1.1 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** I'm at a loss. Any ideas?

Read the article
Fixed and dynamic IPs in ISC DHPD lead to double lease

- by GorillaPatch

I would like to have a small dynamic adress part and the most clients are assigned a fixed IP adress. My dhcpd.conf looks like this: use-host-decl-names on; authoritative; allow client-updates; ddns-updates on; # Einstellungen fuer DHCP leases default-lease-time 3600; max-lease-time 86400; lease-file-name "/var/lib/dhcpd/dhcpd.leases"; subnet 192.168.11.0 netmask 255.255.255.0 { ddns-updates on; pool { # IP range which will be assigned statically range 192.168.11.1 192.168.11.240; deny all clients; } pool { # small dynamic range range 192.168.11.241 192.168.11.254; # used for temporary devices } } group { host pc1 { hardware ethernet xx:xx:xx:xx:xx:xx; fixed-address 192.168.11.11; } } The motivation for the pool declaration with deny all hosts comes from the ISC DHCPD homepage http://www.isc.org/files/auth.html This will allow hosts to be first added to the network, where they will receive a temporary IP from the 241-254 adress range and then later write an explicit host declaration. Upon next connect it will receive the right configuration. The problem is that I am getting error messages that 192.168.11.13 has a dynamic and a static lease. I am a bit confused as I expected the pool declaration with deny all clients would not count as dynamic. Dynamic and static leases present for 192.168.11.13. Remove host declaration pc1 or remove 192.168.11.13 from the dynamic address pool for 192.168.11.0/24 Is there a way to have the DHCP server send an DHCPNA to clients if they have a host statement and retain this dynamic range?

Read the article
Apache2 shared server: default webpage

- by Eamorr

Greetings, I have an apache2 server with 4 domain names point to my server's single IP address. When I type in www.site1.com it serves pages from /home/eamorr/site1/index.php Same for www.site2.com, www.site3.com and www.site4.com However, when I type in to the address bar of a browser without the www, it always redirects to site1.com! i.e. site1.com - site1.com site2.com - site1.com site3.com - site1.com site4.com - site1.com How do I configure apache to do the following: site1.com - site1.com site2.com - site2.com site3.com - site3.com site4.com - site4.com Here is my default config: ServerAdmin [email protected] ServerName www.site1.com DocumentRoot /home/eamorr/sites/site1.com/www DirectoryIndex index.php index.html <Directory /home/eamorr/sites/site1.com/www> Options Indexes FollowSymLinks MultiViews Options -Indexes AllowOverride all Order allow,deny allow from all php_value session.cookie_domain ".site1.com" #Added by EOH for redirection RewriteEngine on RewriteRule ^([^/.]+)/?$ driver.php?uname=$1 [L] </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined I'd like to look at the domain name and then redirect to www.sitex.com. Is there an Apache rule to do this? I hope someone can help. My SysAdmin/apache2 config skill aren't the best. Many thanks in advance,

Read the article
Multiple IP's using one NIC connectivity problem - Windows

- by Vincent

I have a frame relay network that is directly connected to a GPRS network. I also have a ADSL high speed network and recently I have been trying to achieve the following network configuration using windows 7 (Also tried XP) with no success to date. On one server I have two NIC's NIC1 I would like the following two static IP address's 10.0.1.110 and 10.0.1.200 the cisco router has a default gateway of 10.0.1.1 the ADSL is DHCP. NIC1 and the cisco router do not have access to the internet. NIC2 is setup for DHCP with a primary DNS and secondary DNS configured to enable internet connectivity. With NIC1 all incoming TCP connections are from IP address's starting with 10.192.x.x I cannot establish a TCP connection to both 10.0.1.110 and 10.0.1.200. Its either one or the other. I have a static route implemented in windows of: route -p 10.192.0.0 mask 255.255.0.0 10.0.1.1 metric 1 I have tried leaving out the gateway in the NIC1 and many other combinations with no success. Can anyone please help? What am I doing wrong?

Read the article
PLESK PostFix Error Local in maillog, how to troubleshoot

- by RCNeil

I'm using the PHP mail() function, using PostFix, on CentOS6, Plesk 10.4, and my email is not getting delivered to a particular address. My personal GMail and Yahoo email addresses receive email from my server fine and do not produce errors. After a wonderful suggestion on here, I checked my mail logs, and this is the error I see : Apr 10 10:26:29 ######### postfix/qmgr[8323]: 19EA21827: from= <[email protected]>, size=645, nrcpt=1 (queue active) Apr 10 10:26:29 ######### postfix-local[8331]: postfix-local: [email protected], [email protected], dirname=/var/qmail/mailnames Apr 10 10:26:29 ######### postfix-local[8331]: cannot chdir to mailname dir name: No such file or directory Apr 10 10:26:29 ######### postfix-local[8331]: Unknown user: [email protected] Apr 10 10:26:29 ######### postfix/pipe[8330]: 19EA21827: to=<[email protected]>, relay=plesk_virtual, delay=0.15, delays=0.11/0/0/0.04, dsn=2.0.0, status=sent (delivered via plesk_virtual service) Apr 10 10:26:29 ######### postfix/qmgr[8323]: 19EA21827: removed [email protected] is the name I've declared in php.ini for sendmail_from = "[email protected]" sendmail_path = "/usr/sbin/sendmail -t -f [email protected]" and the recipient is supposed to be [email protected]. Is this an error on my side or the recipients? Can I address this on my server? Many thanks SF.

Read the article
Error setting up Blackberry Internet Service with Outlook Web Access

- by Travis

I'm trying to set up Blackberry Internet Service to connect to our Windows SBS2003 outlook web access. I've tried every possible combination of credentials by I always get the same error: An error occured during email account validation. Please check your information and try again. If the error persists please contact your System Administrator. The fields are the following: Outlook Web Access URL: http://mail.domain.com/exchange (I've also tried just using the IP address http://000.000.000.000/exchange with no effect). User Name: JohnDoe (same as OWA login / domain username - I've also tried DOMAIN\JohnDoe) Email Address: [email protected] Mailbox Name: This one confused me a little bit, but it seems it should be the same as the domain username (eg. JohnDoe). I've also tried DOMAIN\JohnDoe, and a number of other things. No matter what I do, I get the same error message. At this point, I'm basically just trying things, because I don't really know how this service is supposed to work. Does anyone know what causes this particularly vague error message, and what I can change either in my email settings or on our exchange server to resolve this?

Read the article
Delete ARP cache on Mac OS when moving from one Wifi network to the other

- by Puneet

I am facing wireless connectivity problems when I move from one Wifi network to the other. Here is how it happens: I am at my friends place. I connect to his Wifi. His Wifi router ip address is 192.168.0.1. Everything is fine I close my laptop, come back to my house, open my laptop and I connect to the Wifi Network at my place. Different ESSID, but the Wifi router address is the same 192.168.0.1. At this point I cant get to anything on the internet. To debug I try to see if I can ping the router (192.168.0.1), I cant. I get a no route to host. Meanwhile airport tells me Im connected to Wifi. I see the arp cache and I see a permanent entry for 192.168.0.1 ? (192.168.0.1) at 5c:d9:98:65:73:6c on en1 permanent [ethernet] This permanent bit looks problematic. I go ahead and delete the arp cache entry and all is fine with the world until I go back to my friends place where the same situation plays out. Now my question is, why the hell is this happening? If there is no way around it, can I run a script on Wifi connect/disconnect to clear out the arp cache? Im using Mac OS X $uname -a Darwin 10.8.0 Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386 i386

Read the article
Websockets Server with Fault-Tolerance and Durable Message Store

- by smitchell360

I am starting to experiment with websockets. Does anyone know of a websockets server (open source or paid) that provides a durable store of the websocket "channel"? All of the examples that I have found do not address durability -- if a websockets server goes down, all "channel" data is lost. Services such as Pusher do not really discuss whether they address the durability issue (and I have not received a response from tech support yet). Happy to roll my own, but would rather not reinvent the wheel. EDIT: I'm not looking for websockets 101 information. That is readily available and understood. I'm looking for a server (open source or paid) that supports websockets and has a durable store for the websocket data so that, in the event that a server fails, a new server can take over where the original one left off. Two main purposes: 1. support failover scenarios contemplated by the websockets Network Working Group http://tools.ietf.org/html/draft-ibc-websocket-dns-srv-02#section-5.1 (most importantly so that missed messages are sent when a client connects to a failover server) 2. support scenarios where new subscribers must receive all past messages that were published. Of course this can be handled at the application layer...but that is not what I am looking for. EDIT So, after some research the following installed options seem to be the most robust: Kaazing Migratory Migratory (http://migratory.ro) Hosted services that seem "real" Pusher (great API but no history feature yet) PubNub (has history) All of the above services have graceful fallback to other communication methods if websockets are not available. I was not able to find any open source that provided "out of the box" clustering, fail-over, and a durable message store to play back history. There are some projects that may serve as good starting points, but not exactly what I am looking for.

Read the article
Linksys wireless router will not hardware reset.

- by Jack M.

Hello, all. I'm unable to make my router perform a hardware reset, and I cannot understand why. All was working well, except that my iPhone could not connect to the wireless. I found that the router was only allowing AES encryption on WPA2 Personal mode, so I upgraded the firmware. I updated the firmware to Ver.1.06.1, and everything went screwy. The router is no longer showing up in the WiFi list (as Linksys, or its previous network name). Wiring into the router gives me an IP address from my ISP (24.121.121.XXX). Attempting to do a hardware reset, but the power light never starts flashing and the router does not seem to reboot. My machine wired in is still online with no interruption in WoW. Pulling the power cord to force a reset returns it to the same state. I even went so far as to pull up my previous IP address (from DynDNS) and try to connect to that, but it wont even ping. What I'm trying to find out is: Did the new firmware fry the thing, or is there some way to fix this? Thanks in advance for any help.

Read the article
management network to a network port for additional ones munin and monit

- by paolo

management network to a network port for additional ones munin and monit I want to build a separate Netzwek for server management. I have several network cards a linux / debian / ubuntu with computer. Set both network cards sin in the /etc/network/interfaces. # The primary network interface #allow-hotplug eth0 #iface eth0 inet dhcp auto eth0 iface eth0 inet static address 10.0.0.240 netmast 255.255.255.0 network 10.0.0.0 brodacast 10.0.0.255 gateway 10.0.0.254 auto eth1 iface eth1 inet static address 10.0.10.240 netmast 255.255.255.0 network 10.0.10.0 brodacast 10.0.10.255 post-up ip route add 10.0.0.0/24 dev eth0 src 10.0.0.240 table eth0-WAN post-up ip route add default via 10.0.0.254 table eth0-WAN post-up ip route add 10.0.10.0/24 dev eth1 src 10.0.10.240 table eth1-LAN post-up ip route add default via 10.0.10.200 table eth1-LAN post-up ip rule add from 10.0.0.240 table eth0-WAN post-up ip rule add from 10.0.10.240 table eth1-LAN still i adjusted / etc/iproute2/rt_tables and following routes set up in the /etc/network/interfaces I want to have both applications and the network interface separately as munin and monit only on eth1 and not have to eth0. it goes to the reboot but sometimes not always. # Traceroute-i eth1 10.0.10.200 not go what am I doing wrong?

Read the article
Persistent routes for DD-WRT PPTP VPN client

- by Tim Kemp

My home network in the USA is behind a Buffalo router (G300NH) running their version of DD-WRT. I use the built-in PPTP VPN client to connect to a VPN provider in the UK. I route certain traffic over the VPN (so it has a UK source address, for various entirely legal reasons) which I achieved by following the instructions in the DD-WRT docs and my VPN provider's own instructions. I placed two commands like this in the firewall script: route add -net xxx.xxx.0.0 netmask 255.255.0.0 dev ppp0 route add -net yyy.yyy.0.0 netmask 255.255.0.0 dev ppp0 I didn't put any of the iptables rules in since it my setup doesn't seem to need them. It works like a charm. Traffic to the xxx subnets goes over the VPN, everything else goes out over my ISPs own pipes. The problem comes when the VPN drops, which it does occasionally. DD-WRT does a fine job of reconnecting it automatically, but the routes are trashed every time that happens. How do I automate the process of re-establishing my routes? I thought about static routes, but the IP address of the VPN connection is dynamically assigned (which is why I'm using dev ppp0). Many thanks, Tim

Read the article
DNS stops working occasionally

- by Andrey

I have tried using Google DNS and the one provided with DHCP. At some point my PC (Windows 7) stops resolving domain names, but DNS server is perfectly pingable. What can be the reason? Thanks! Edit: It is really weird. It can stop and start working in few seconds. The problem is that DNA requests are timing out, and the problem is that the DNS server is pingable at the same time. I can't understand how this could be possible and what might be an issue. C:\Windows\System32\drivers\etc>nslookup google.com DNS request timed out. timeout was 2 seconds. Server: UnKnown Address: 8.8.8.8 Non-authoritative answer: Name: google.com Addresses: 173.194.78.102 173.194.78.101 173.194.78.139 173.194.78.113 173.194.78.100 173.194.78.138 C:\Windows\System32\drivers\etc>nslookup google.com DNS request timed out. timeout was 2 seconds. Server: UnKnown Address: 8.8.8.8 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out

Read the article
Test server on a local network with XAMPP

- by hopscotch1978

Hi, I'm not very proficient with networks and could use some help. I've got a Win 7 desktop with XAMPP which acts as my local dev machine. I've configured a virtual host on the desktop which I'm able to access fine. If I'm understanding things correctly, the virtual host uses port 80 (<VirtualHost 127.0.0.1:80>). I've just tried to configure a separate Win XP laptop on the local wireless network to connect to the main desktop for testing purposes. I've added the IP address and virtual host name to my Hosts file on the laptop. My virtual host is imaginatively named "virtualhost1". When I type this into my laptop browser, it connects correctly to the main desktop and I get the XAMPP welcome screen. But I can't seem to get to the actual site, just the XAMPP welcome screen. It kind of jumps the browser to http://virtualhost1/xampp/. I think it's a port issue of some sort but I have no idea how to resolve it. I would get the same XAMPP welcome screen on my desktop if I omitted ":80" from the virtual host declaration. On my main desktop, typing "virtualhost1" to the browser address bar gives me the site correctly, not the XAMPP welcome screen. Help would be appreciated. Thank you.

Read the article
How to fake ip at localhost without LoopBack.

- by sexer

How can i fake an ip on my own PC? for example if there were an ip address lets say 201.91.81.71, that Host is somewhere outside of my red and is hosting a webserver. How can set a website on my own PC, and when i go to browser and try to explore 201.91.81.71 it actually explore the website at my own PC? pd: I need it with IP addresses not domain names, since I need to implement it on a non-web service. First guess was installing a LoopBack with 201.191.81.71 as ip, but since some times the subnet works and some other it doesn't isn't a stable solution. Second guess was adding a route to route table : route add 201.91.81.71 mask 255.255.255.255 192.168.1.2 192.168.1.2 is the ip address of my NIC. If i could add this route it would work but windows doesn't let me do so. route add 201.91.81.71 mask 255.255.255.255 127.0.0.1 it doesn't let me set as gateway 127.0.0.1 if 201.91.81.71 isn't set in a NIC, so thats why i set sometimes loopback and this route add is auto, but it needs a subnet mask which doesn't match the ip and cannot set 255.255.255.255, im in real throubles here. can i get some help? thx.

Read the article
Why am I unable to reach local network computers, but able to browse the web?

- by Igor Zinov'yev

I have a weird problem. Today after turning my Ubuntu 9.10 PC on I can't connect to my local network, but I can use the Internet. We have a single Windows 2003 server machine that acts as a local main DNS server, DHCP server and a domain controller. Although it seems to give me the local IP address, I can not ping it, as well as any other machine on the net. I have tried all of the below and it didn't help: Rebooting; Reconnecting to the network; Forcing the dhclient to renew the IP address; Deleting and creating new connection profiles; Plugging my machine into another network outlet; Maybe it has something to do with routing, because I have tampered with routing tables the day before, but the tables seem ok to me: $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 vboxnet0 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 Our LAN uses a D-Link DI-604 router, and it looks to me as if I am connected to the network outside the router. I can not even access its administration page. Please at least suggest what I can do to solve this. P.S. What seems strangest to me is that I can access the PC in question from outside the network by opening a port on the router. I have managed to ssh to it from outside, but I still can't ping nothing on the inside. P.P.S Today I tried reinstalling network-manager with --purge option, but it did no good. After that I created a new DCHP reservation for my PC in order to change my local IP, but that didn't change anything either. My PC is able to get a DHCP offer, but then it's unable to connect to any local computers. I am desperate.

Read the article
What does "cpuid level" means ? Asking just for curiosity

- by ogzylz

For example, I put just 2 core info of a 16 core machine. What does "cpuid level : 6" line means? If u can provide info about lines "bogomips : 5992.10" and "clflush size : 64" I will be appreciated ------------- processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 6 model name : Intel(R) Xeon(TM) CPU 3.00GHz stepping : 8 cpu MHz : 2992.689 cache size : 4096 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 fpu : yes fpu_exception : yes cpuid level : 6 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl vmx cid cx16 xtpr lahf_lm bogomips : 5992.10 clflush size : 64 cache_alignment : 128 address sizes : 40 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 6 model name : Intel(R) Xeon(TM) CPU 3.00GHz stepping : 8 cpu MHz : 2992.689 cache size : 4096 KB physical id : 1 siblings : 4 core id : 0 cpu cores : 2 fpu : yes fpu_exception : yes cpuid level : 6 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl vmx cid cx16 xtpr lahf_lm bogomips : 5985.23 clflush size : 64 cache_alignment : 128 address sizes : 40 bits physical, 48 bits virtual power management:

Read the article
Vlans and subinterfaces

- by Adeodatus

I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

Read the article
Chrome browser completely messing with network?

- by kiasecto

I have a bizare problem with Google Chrome on a intel core i5 running windows 7 32bit. Whenever chrome is installed, access to other computers in the home group becomes really slow - such as opening shares. Its becomes really slow to resolve windows names. Something goes hay-wire with the local network - pining local machines which is usually 0mS pings I get random timeouts and random successes. Whenever I try to load a local address inside of chrome (including localhost, 192.168.0.1 etc) - it always says something in the status bar about resolving proxy and times out after about 5 seconds, then seems to work fine. If I go to settings inside of chrome, it just brings up the internet explorer connection settings, where I have not set any proxy settings. One I uninstall chrome, all these problems go away. Network shares and name resolvings work instantly, pings to any machines never have a problem. Localhost and other network IP address work fine in all other browsers. Anyone heard of this problem before and know what it might be? I even tried re-installing winodws 7 and the problem came straight back when chrome was loaded on again.

Read the article
How to configure IIS for SVG and web testing with Visual Studio?

- by macias

Let's say I have a simple web page with svg image in it: <img src="foobar.svg" alt="not working" /> If I make this page as static html page and view it directly svg is displayed. If I type the address of this svg -- it is displayed. But when I make this as .aspx page and launch it dynamically from Visual Studio I get alt text. If I type the address of this svg (from localhost, not as a local file) -- browser tries to download it instead of displaying. I already defined mime type in IIS (for entire server -- "image/svg+xml") and restarted IIS. Same effect as before. Question: what should I do more? Update WireShark won't work (it is in documentation), I tried also RawCap, but it cannot trace my connection (odd), luckily Fiddler worked: From client: GET http://127.0.0.1:1731/svg/document_edit.svg HTTP/1.1 Host: 127.0.0.1:1731 User-Agent: Mozilla/5.0 (Windows NT 6.1; rv:10.0.1) Gecko/20100101 Firefox/10.0.1 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip, deflate Connection: keep-alive Answer from server: HTTP/1.1 200 OK Server: ASP.NET Development Server/10.0.0.0 Date: Thu, 16 Feb 2012 11:14:38 GMT X-AspNet-Version: 4.0.30319 Cache-Control: private Content-Type: application/octet-stream Content-Length: 87924 Connection: Close <?xml version="1.0" encoding="UTF-8" standalone="no"?>  <svg xmlns: *** FIDDLER: RawDisplay truncated at 128 characters. Right-click to disable truncation. *** For the record, here is useful Q&A for Fiddler: http://stackoverflow.com/questions/826134/how-to-display-localhost-traffic-in-fiddler-while-debugging-an-asp-net-applicati

Read the article
OpenVZ with brdiged interfaces and VLAN

- by Deimosfr

Hi, I've got a problem with OpenVZ with brdiged VLAN. Here is my configuration : +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN working on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110 : inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seams working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks like ok, but when I start my VE, here is the message : ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please ? Thanks

Read the article
Cannot connect to windows server by name over vpn connection

- by ErocM

I have a rented dedicated windows server on a public ip that is acting as a SQL Server and VPN server. I need to connect to this server via computer name to get replication in place. I cannot use an ip address due to this issue: So, due to this, we are going the VPN route. That is my primary issue: After I am connected to this server's vpn, I can connect to SQL Server using the ip address but I cannot connect by the computer's name as you can see below... Right now, there is no hardware firewall on it since I had it removed to test this issue. I am running Windows 2008 Enterprise Server as the VPN server. I am not sure if the route print will help any from the workstation trying to connect but here is the info: IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.0.0.0 10.0.0.1 10.0.0.2 21 10.0.0.2 255.255.255.255 On-link 10.0.0.2 276 Any other info needed? Thanks for the help! ========= CLARIFICATION ON A FEW THINGS #1 ========= This is the server's info: This is the workstation that is trying to connect: I connect to the server via "Control Panel\Network and Internet\Network and Sharing Center\Connect or Disconnect" You can see here that I am connected: ========= CLARIFICATION ON A FEW THINGS #2 ========= I've tried to connect directly to the Sql Server as I did above but with the computers name and I couldn't get to it. Here I am trying to net view it from the workstation and it couldn't find it:

Read the article
Courier IMAP always disconnects since update

- by Raffael Luthiger

Since one of our customers updated their server courier does not handle IMAP connections properly any more. POP3 works without any problems. When I try to test IMAP with telnet then it is always like this: $ telnet domain.com 143 Trying 188.40.46.214... Connected to domain.com. Escape character is '^]'. * OK [CAPABILITY IMAP4rev1 UIDPLUS CHILDREN NAMESPACE THREAD=ORDEREDSUBJECT THREAD=REFERENCES SORT QUOTA IDLE ACL ACL2=UNION STARTTLS] Courier-IMAP ready. Copyright 1998-2011 Double Precision, Inc. See COPYING for distribution information. 01 LOGIN [email protected] test Connection closed by foreign host. I enabled debugging in the authdaemond but the output does not really help much: Apr 12 23:10:04 servername authdaemond: received auth request, service=imap, authtype=login Apr 12 23:10:04 servername authdaemond: authmysql: trying this module Apr 12 23:10:04 servername authdaemond: SQL query: SELECT login, password, "", uid, gid, homedir, maildir, quota, "", concat('disableimap=',disableimap,',disablepop3=',disablepop3) FROM mail_user WHERE login = '[email protected]' Apr 12 23:10:04 servername authdaemond: password matches successfully Apr 12 23:10:04 servername authdaemond: authmysql: sysusername=<null>, sysuserid=5000, sysgroupid=5000, homedir=/var/vmail, [email protected], fullname=<null>, maildir=/var/vmail/domain.com/test, quota=0, options=disableimap=n,disablepop3=n Apr 12 23:10:04 servername authdaemond: Authenticated: sysusername=<null>, sysuserid=5000, sysgroupid=5000, homedir=/var/vmail, [email protected], fullname=<null>, maildir=/var/vmail/domain.com/test, quota=0, options=disableimap=n,disablepop3=n Right after the "Authenticated" line the output stops. There is no other message. And in no other log file I've checked I could find any other related message. The system was updated from Ubuntu 10.10 to 12.04. How could I get more information? Or does anybody have an idea what could go wrong here?

Read the article
How is a subdomain passed to the webserver?

- by Joshua Frank

I know that dns resolves an address like example.com to an IP address like 11.22.33.44, but I'm a little confused about how subdomains are resolved, so that when you type http://subdomain.example.com, what actually gets passed to the server at 11.22.33.44? In other words, example.com = 11.22.33.44, but subdomain.example.com/path = ??? Are "subdomain" and "path" passed as http headers, or mapped in the url in some way, or what? Thanks in advance. Edit: If I'm understanding correctly, BloodPhilia says that subdomain.example.com actually is a different domain that in principle could resolve to a totally different IP. But if that's so, then what about hosts that have huge numbers of (what look like) subdomains, but which actually map to some path on the site. For instance, blogspot hosts millions of blogs, and they all look like this: aaa.blogspot.com bbb.blogspot.com ...millions more... yyy.blogspot.com zzz.blogspot.com Those are clearly not subdomains with their own IP's, but rather some mapping like aaa.blogspot.com -- www.blogspot.com/aaa, but how is this accomplished? What actually gets passed to the web server at blogspot.com?

Read the article
Using proxy.pac to access Apache 2 with a hostname?

- by leeand00

Note that I do not have a DNS on my network, and that is why I am resorting to using a proxy.pac file. I would like to be able to access my development Apache 2 server using a name instead of an ip without setting up a full blown DNS. I am aware of setting names in the C:\Windows\System32\drivers\etc\hosts file and the /etc/hosts files, however I cannot edit the hosts file on all of the devices that I am testing the site on. I've added a proxy.pac file to my Apache2 server and pointed my browsers settings to it at: http://192.168.2.221/proxyutils/proxy.pac ...where 192.168.2.221 is thehostname's ip address. I set the above URL in Firefox in the following manner: From the menubar selecting "Edit-Preferences" In the resulting "Firefox Preferences" window clicking the "Advanced" tab. Clicking the "Network" tab Clicking the "Settings" button. Selecting the "Automatic proxy configuration URL:" radio button. Entering http://192.168.2.221/proxyutils/proxy.pac and pressing OK. The contents of the proxy.pac file on the Apache server function FindProxyForURL(url, host) { if( dnsDomainIs(host, "thehostname") ) return "PROXY 192.168.2.221:80"; return "DIRECT"; } In Firefox I then access the following URL: http://thehostname/wp-blog/ And instead of the development version of the Wordpress blog I am trying to access I get a URL of http://thehostnamehttp/thehostname/wp-blog/ in my address bar and a 404 Not Found page in the browser window. Looking over proxy.pac, it seems like calling dnsDomainIs shouldn't work considering I don't have a DNS setup on my network, but I've also tried just comparing the host argument with the string "hostname" and it yielded the same result, even after modifying the proxy.pac file and clicking the reload button near the proxy settings. This could also be a Wordpress problem, since I've noticed that directories without Wordpress seem to function perfectly normally. (see cross post here) Is there any way I can modify my configuration so that I can access the site using http://thehostname/wp-blog/ ?

Read the article
Ubuntu Server attack? how to solve?

- by saky

Hello, Something (Someone) is sending out UDP packets sent from our whole ip range. This seems to be multicast DNS. Our server host provided this (Our IP Address is masked with XX): Jun 3 11:02:13 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:23 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:32 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:35 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 I checked my /var/log/auth.log file and found out that someone from China (Using ip-locator) was trying to get in to the server using ssh. ... Jun 3 11:32:00 server2 sshd[28511]: Failed password for root from 202.100.108.25 port 39047 ssh2 Jun 3 11:32:08 server2 sshd[28514]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.100.108.25 user=root Jun 3 11:32:09 server2 sshd[28514]: Failed password for root from 202.100.108.25 port 39756 ssh2 Jun 3 11:32:16 server2 sshd[28516]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.100.108.25 user=root ... I have blocked that IP address using this command: sudo iptables -A INPUT -s 202.100.108.25 -j DROP However, I have no clue about the UDP multicasting, what is doing this? who is doing it? and how I can stop it? Anyone know?

Read the article

< Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249 | Next Page >