Search Results

Search found 11973 results on 479 pages for 'ip conflict'.

Page 244/479 | < Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >

• Internet in the router but not in the local network.

  - by TheMouse

  I have a PC and a laptop (Windows 7 - both) which should connect through router to Internet. The router is Linksys wrt120. My ISP is using PPPoE. I have connected the Internet cable to the router, clone the MAC of my PC, writing the username and the password for my Internet connection. After seconds the router has acquired IP from my ISP. I have used the administration panel of Linksys and with the help of the ping and tracert commands which are built into it - I can connect to the world, outside the network. The problem is when I try to connect the PC or the laptop to the network. There's no problem here. The DHCP server of the router gives them appropriate addresses. The problem is that they couldn't connect to either Internet addresses (google.com) or IP addresses. But they can connect to the router and its control panel. I tried several times, reset the router..but there's no Internet..still.

  Read the article

• How can I change the binding order of network adapters in Windows 7?

  - by Chris Farmer

  The end goal here is that I am trying to install an Oracle 10g server on my Windows 7 x64 dev box. I use DHCP, and the Oracle installer is throwing up this warning: Checking Network Configuration requirements ... Check complete. The overall result of this check is: Failed <<<< Problem: The install has detected that the primary IP address of the system is DHCP-assigned. Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system. See the Installation Guide for more details on installing the software on systems configured with DHCP. I have installed the loopback adapter, but I am not sure how to make it the primary network adapter. I see this Microsoft KB article on the subject but it's Windows XP-oriented, and I can't seem to find a comparable one for Windows 7. Some of the options it talks about don't seem to be present in the views of the adapters that I see. So, how can I make the loopback adapter become the primary adapter?

  Read the article

• reverse proxying with NGINX to two back-end servers

  - by aag

  I am trying to learn how to configure the Nginx proxy. All requests from external (www.external.com) should go to internal server 10.10.10.16:2080, except for www.external.com/nagios requests, which should go to internal 10.10.10.18. My location block looks as follows: location ~* / { proxy_buffers 16 4k; proxy_buffer_size 2k; proxy_buffering off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Accept-Encoding ""; proxy_pass http://10.10.10.16:2080; } # # nagios server location ~* /nagios/ { proxy_buffers 16 4k; proxy_buffer_size 2k; proxy_buffering off; # proxy_set_header Host $host; # proxy_set_header X-Real-IP $remote_addr; # proxy_set_header Accept-Encoding ""; proxy_pass http://10.10.10.18; } The first location seems to work fine. However, any request to www.external.com/nagios sends the browser into the eternal pastures. Of course, 10.10.10.18/nagios was tested and works fine. What am I missing?

  Read the article

• What is the "in-the-wire" size of a ethernet frame? 1518 or 1542?

  - by chrisapotek

  According to the table here, it says that MTU = 1500 bytes and that the payload part is 1500 - 42 bytes or 1458 bytes (<- this is actually wrong!). Now on top of that you have to add IPv4 and UDP headers, which are 28 bytes (20 IP + 8 UDP). That leaves my maximum possible application message to as 1430 bytes! But by looking for this number in the Internet I see 1472 instead. Am I doing this calculation wrong here? All I want to find out is the maximum application message I can send over the wire without the risk of fragmentation. It is definitely not 1500 because that includes the frame headers. Can someone help? The confusion is the the PAYLOAD can actually be as large as 1500 bytes and that's the MTU. So now what is the size in-the-wire for a payload of 1500? From that table it can be as big as 1542 bytes. So the maximum app messages I can send is 1472 (1500 - 20 (ip) - 8 (udp)) for a maximum in the wire size of 1542. It amazes me how things can get so complicated when they are actually simple. And I have not clue how someone came up with the number 1518 if the table says 1542.

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• I've got very brazen pop3 attack how to protect the server?

  - by Ken Tang

  Today I have brazen attack to my pop3-dovecot server and mail log is full over (200MB) with this kind of information: Nov 11 09:28:14 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<shawn>, method=PLAIN, rip=200.233.152.111, lip=myip Nov 11 09:28:14 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<shop>, method=PLAIN, rip=200.233.152.111, lip=myip Nov 11 09:28:14 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<sitetest>, method=PLAIN, rip=200.233.152.111, lip=myip Nov 11 09:28:14 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<solar>, method=PLAIN, rip=200.233.152.111, lip=myip Nov 11 09:28:15 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<services>, method=PLAIN, rip=200.233.152.111, lip=myip I just blocked attacker's ip by iptables -A INPUT -s 200.233.152.111 -j DROP But it this can be continued anytime from other ips. My question is: Is there any method to disallow anyone to connect my pop3 server (except only me?) because my ip is dynamic from ISP side so I don't know how to make pop3 server know that it is exactly me connecting to. Thank you in advance!

  Read the article

• MacBook Pro with OSX 10.6.3 (Snow Leopard) Wi-Fi network connection breaks after few minutes

  - by Yanick Landry

  I have a MacBook Pro with OSX 10.6.3 (Snow Leopard). After connecting on a Wi-Fi network, the connection "breaks" after a few minutes. What I mean by "breaking" is that all requests, whether it is loading a web page, connecting to a share folder, connecting to my local router at 192.168.0.1, or pinging anything doesn't get through (time out). When in a "break" situation, I can see in the Network Settings panel that I still have an active IP, which I can successfully ping. I have this problem at home with a router D-Link DI-624 and at work with a D-Link WBR-2310, all with updated firmwares. I thought DHCP was the issue. So I tried assigning a fixed IP address (192.168.0.166). It successfully connects, but after a few minutes, the connection still breaks. The solution I'm currently using is that I disable the AirPort (on the Network icon menu in the top bar), wait a few seconds then re-enable it. It then quickly works, but the connection still breaks after a few minutes. I tried Googling my problem but I think I can't find any good keywords ! It's my first question here, so sorry if I don't respect some rules.

  Read the article

• Routing for remote gateway over VPN in Vista/7 broken?

  - by Raymond

  Hi, Situation is as follows. Home computer running Windows 7, sets up VPN connection (LT2P + IPSec, "use remote gateway" disabled) to office. Subnet is 192.168.64.x Office has Draytek Vigor 2920 router, subnet is 192.168.32.x What happens? - VPN connection itself works fine - Can ping any machine on the remote network - When trying to open a webpage from a host in the remote network, the remote server logs the incoming request, but the browser hangs on "waiting for..." and eventually times out. I have observed this problem on Windows Vista and Windows 7. On Windows XP however there is no problem like described above. The only clue I have is that there is a difference in the routing between XP and Vista/7. The output of "route print" on Windows XP looks like this: (See www.latunyi.com/routing_xp.png) So here the gateway for the 192.168.32.x subnet is the IP address that the local computer has in the remote network. The output of "route print" on Windows 7 (and Windows Vista) looks like this: (See www.latunyi.com/routing_win7.png") Now the gateway for the 192.168.32.x subnet is the IP address of the VPN router (32.1). I don't know if that causes this trouble, but it seems a bit strange. Enabling "use default gateway on remote network" doesn't make a difference. Using the new option "Disable class based route addition" in Windows 7 only makes the route to the VPN router disappear. I am really puzzled here. I assume the VPN routing can't be broken in both Vista and Windows 7, and this should just work without manually adding routes. I hope someone has a solution for this problem :-). Thanks!

  Read the article

• named responding recursive on norecurse queries

  - by Keks

  I have a server on which named is running. It is intercepted with another named server which it is not aware of. Querying the first named server results in timeouts. The server tries to resolve the query recursively. During that the firewall redirects the DNS Request from the first named server to the second one (the query from the first one is addressed to a e.g. a root server and has its "Recursion desired" bit set to 0). Despite that the second named responds to this request with a entirely or at least 1 level more resolved response than the first named server expects. So it ends up with a timeout even though it got a correct name server or even the full IP for the queried domain. In the first case the first name server tries to follow the authority domain ignoring the coresponding glue record and ends up in a loop it aborts: queried: google.com -> got from named#2: ns1.google.com -> ignore glue record and query: ns1.google.com -> got authority from named#2: google.com In the second case it ignores the answer section with the correct IP and instead tries to follow the name servers from the authority section, which ends up in the same dead end as case 1. So how can it be that the second named responds with recursive results even though the bit was explicitly set to 0 in the request from the first named?

  Read the article

• Which steps are required to avoid my server being considered as spam sender?

  - by Cyril N.

  I'm looking to set up a webmail server that will be used by a lots of users that will receive and send emails. They will also have the possibility to forward emails they receive. I'd like to know which steps are recommanded/required to indicate to others Mail services (GMail, Outlook, etc) that my server is not used as a spam sender (disclaimer : IT's NOT ! :p) but a legitimate one. I know I have to define a SPF TXT records for example, but what others steps would you recommend me to do ? For example, is there a formula like having a proportional number of servers based on the amount of email sent (for having a different IP address) ? (something like sending a maximum of 1M emails / per IP / per day ?) Something else I'm missing ? I tried to search online, but I mostly find how to avoid emails sent with scripts (like PHP) being put in the SPAM folder. I'm looking for a server/dns configuration side. Thanks a lot for your help/tips, I appreciate !

  Read the article

• Easiest way to do host name resolution with IPA?

  - by Luke

  We are currently using static LAN IP addresses for our internal non-public facing servers. We don't have DHCP configured. We're using Vyatta for our router and firewall. The firewall is configured to be zone based. We want to setup IPA for centralized authentication (LDAP+Kerberos). IPA is requiring resolvable host names. I want to avoid having to enter DNS records by hand. What is the most painless way to make host names resolvable that works with IPA in a Linux only environment? We arn't using anything to resolve host names now. Up until now we've been using static ip addresses and local users on each server. We've looked at BIND, DHCP (does that even solve the problem?), and multicast DNS. At this point we're not sure which solution would work best. Is there another option we haven't considered? Security is very important. We have multiple zones where each zone has very specific or no access to another zone. DNS for public domains is forwarded from Vyatta to our ISP's DNS server.

  Read the article

• How does Google geo location service work?

  - by heaosax

  I dont use google maps much, but I was using it today and I clicked the "Show my location" button for the first time, then firefox asked for permission and I clicked "share my location", google maps showed my location pretty accurate. But, how does this system really works? I mean how can google know where I live? I am connecting to the internet with a VPN, so my "public IP" is not from my country, but from sweden, also I use linux and I change the mac of my wireless device, but google still show my location. I know I can disable this feature setting firefox about:config geo.enabled to false, but I am curious about how google can know where I live even when I dont have a real mac address and my IP is not from my real country. Basically I'd like to know if this feature works only because of code that exists in chrome and firefox (which spies my system)? I am worried about anyone knowing where I live, I mean... where is my privacy? Part of the fun about the internet is remaining anonymous.

  Read the article

• How to handle OpenVPN client as a service, when the laptop is physically on the network already?

  - by James

  The Setup I've gotten OpenVPN working on our Windows XP laptops. Users are limited, so I went ahead and set OpenVPN client to run as a service, which is great anyway because that means they are on the VPN before logging in, so login scripts work, plus we can do remote support even if the user can not log in (such as connecting via VNC or resetting passwords). It is also configured to send all traffic over the tunnel, so when, for example, they browse the internet it is just like browsing from our corporate network. The Qestion(s) So, I'm wondering how does the OpenVPN client act when the computer is already physically on the same network as the OpenVPN server? Right now, the client is configured to connect the the public dns name which will resolve to the public ip address which will NOT get reflected back to the OpenVPN server, so it is affectively blocked from connecting to the OpenVPN server while on the network. Is that a good thing? Or will it constantly try to connect, using up system resources and network resources? We will likely have hundreds of laptops regularly on the physical network with this, so it could contribute to a lot of unnecessary network chatter. Alternatively Would it be better to have the firewall reflect the port back to the OpenVPN server and let it connect? Or have our internal dns resolve the name to the private ip and allow them to connect directly? Would traffic then go over the vpn connection (which I do not want, when already on the physical network)? Or is it possible to tell it to ignore the connection when the client and server are already on the same network? TLDR What's a sane way of handling OpenVPN client running as an always-on service when the client and server will often be on the same network?

  Read the article

• Losing internet connection after few minutes (5-10 maybe)

  - by Korchkidu

  I took a computer that was not updated for months. Internet was working just fine so basically, I updated zonealarm, avast and installed all windows updates and especially SP3. After that, when I reboot, Internet works fine but after few minutes, Firefox says that the connection was reset. IE does not work either. However, my connection is still up and running as I can make a ping on www.google.com for example. Here are the solutions I tried with no success so far: 1) Uninstalling SP3; 2) Uninstalling IE8 and IE7; 3) Manually setting DNS and IPs; 4) Removed proxy settings from Firefox and IE; 5) Restarting DNS and DHCP related services; 6) Reset TCP/IP with netsh int ip reset c:\resetlog.txt; 7) Updated my ehternet card driver; 8) Restarted, tweaked all the connections in any directions and any configuration possible I believe; 9) Disabled Zone Alarm and Avast; Also, update kb981793 always fails on install. Please, help me as I spent two days already on this and I cannot find any solution. If I cannot fix this problem tomorrow, I will have to format-reinstall everything. Thanks for any help. Regards.

  Read the article

• Linux Centos 6 becomes unavailable from time to time - OS&network issue

  - by adoado0

  I am encountering following problem. There is one server (DL160 G5) running Centos 6.3 with default kernel 2.6.32-220.2.1.el6.x86_64 - at this point I'd like to add that issue appeared also at older version - 6.1 and older kernel (do not remember exactly which version). There is cPanel installed and from time to time it becomes unavailable (network connection). What I've checked is (via KVMoIP): load average is completely normal it does not lack memory or disk space when problem occurs no console notifications checked all access logs and there is no sign that it can be caused by a client script cannot even access local interface (127.0.0.1) or main IP address running tcpdump I can only see packets arriving to server - no responses all services seem to be running properly (mail,sql,http,ssh) checked crontab and all clients' crontabs too network port utilisation is low ( up to several Mbits) arriving packet rate is low - hundreds per second (according to tcpdump) console (via kvmoip) works fine, no lags there is no conntrack at this server there is no ipv6 at this server flushing iptables, unloading modules does not resolve problem restarting network does not resolve problem, no errors appear it also occurs when two sepearate networks are configured (and multiple gateways) as well as one IP, one default gw and one network is configured - so it seems network configuration independent it seems to repeat randomly (load,packet rate,bandwith usage,load independent) checked server with different rootkit detection tools - it seems to be clean server has been rebooted, it did not change anything there are no interface errors it apperas randomly can be once a week or several times per day It usually works fine after 1-15 minutes. What I can also check? It is definitely OS issue - there is traffic at interface only in one direction when problem occurs, can not even ping loopback. Any ideas? Recommended checks? Anything I did not checked above.

  Read the article

• Adjust iptables

  - by madunix

  cat /etc/sysconfig/iptables: # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d X.0.0.Y -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp -s X.Y.Z.W --dport 3306 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp -s M.M.M.M --dport 3306 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 21 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT I have the above following IPtables on my linux web server(Apache/MySQL), I want to have the following: Block any traffic from multiple IP's to my web server IP1:1.2.3.4.5, IP2:6.7.8.9 ..etc Limiting one host to 20 connections to 80 port, which should not affect non-malicious user, but would render slowloris unusable from one host. Limit MYSQL port 3306 access on my server only to the following IP range A.B.C.D/255.255.255.240 Block any ICMP traffic.

  Read the article

• Windows Share permissions

  - by Armando

  I have a SQL/File server that I am replicating a File Share and SQL instance, using ArcServer RHA, to a Replica server. Everything seems to work as far as the replication of the SLQ instance and Share is concerned. When I fail over to the Replica server the DNS Host A record is modified to point to the Replica Server IP Address so if I do an NSLOOKUP on ServerA it then points to the IP Address of ServerB. Ans since the SQL instance is named the same I can still map my ODBC connections to ServerA and I can still make a SQL connection. When I try to do a \ServerA\Share I get an error that says I do not have permissions to the Share. I think this is because it uses keberose authentication and the Share is tied to the actual sever host name. I have tried puting in a CNAME and pointing it to ServerA and Disabling Strict Name Checking on ServerB as well as adding the CNAME to the OptionalNames in the registry but I am still getting the error when I have the ServerA powered off. Is there a way to reset the Authentication of the Share to use the DNS Cname?

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• How do I get a network printer installed in ubuntu 9.04?

  - by SoaperGEM

  My girlfriend's work computer now has Linux on one of the partitions, and for the most part it's running fine--except that I can't seem to get the network printers configured right. There are two of them: a Lanier MP 7500/LD275 and a Lanier MP C3000/LD430c, and Linux seems to have found them both automatically. I'll go through the steps of what I did, and what exactly went wrong. I went to Administration Printing, and clicked the new printer button. It searched for printers and found them both, listed under "Network Printers." I added them as new printers in succession. However, when I clicked "Print a Test Page," it failed saying there was a broken pipe. The device URIs were saved as socket://[ip address]:9100. I changed these to lpd://[ip address] per some online tutorial, which at first looked like it might have worked (but didn't). Then when I tried to print a test page, it first said Processing (and sometimes even Processing - printing test page, 4%, but always subsequently displays Idle - /usr/lib/cups/backend/lpd failed. Help! What do I do? It seems like Linux can find these printers just fine, and the drivers seem to be in place, so what's going wrong?

  Read the article

• Can't run utilities/.exe's that use the network from a [DFS] windows share on Windows 2008 servers. Can this be overcome?

  - by Jim Lawhon

  Under Windows Server 2008 I'm unable to run many utilities that use network resources. This works just fine under Windows Server 2003. For example: \\domain\dfs\tools$\bin\sendmail.exe ... \\domain\dfs\tools$\bin\psexec.exe ... echo %_metric% %_value% %_unixtime% | \\domain\dfs\bin\foo$\nc graphite.domain 2003 -w1 Reproducing and maintaining this folder on a large number of servers/vm's is not desirable. Is there a way to allow Windows Server 2008 to run these tools? If so, can this be enabled via GPO or in a fashion that can be scripted during automated builds? Edit: The commands/tools do work just fine, when run from local drives. Edit2: Wget example: d:\scripts\helpers>z:\bin\wget http://www.google.com SYSTEM_WGETRC = c:/progra~1/wget/etc/wgetrc syswgetrc = z:/etc/wgetrc --2011-04-11 00:32:15-- http://www.google.com/ Resolving www.google.com... failed: Host not found. z:\bin\wget: unable to resolve host address `www.google.com' wget can neither use DNS to resolve the IP nor can it use HTTP if provided an IP directly. Edit3: The problem seems to be tied to DFS/DFS shares. Tools run correctly from other normal windows-server file-shares. They also run correctly when run directly from the file-servers behind the DFS. They only fail when we attempt to run them from the DFS UNC path or mapped drives.

  Read the article

• Nginx + Apache + Wordpress redirects to localhost/127.0.0.1

  - by jcrcj

  Anyone know how to fix an issue with Nginx + Apache + Wordpress redirecting to localhost/127.0.0.1? I've tried a lot of different fixes, but none have worked for me. I can go to http://domain.com/wp-admin just fine and use everything there normally. But if I try to go to http://domain.com it redirects to 127.0.0.1. Everything also works fine if I just run through Apache. Here are the relevant portions of my nginx.conf: server { listen 80; server_name domain.com; root /var/www/html/wordpress; location / { try_files $uri $uri/ /index.php; } location ~ \.php$ { proxy_pass http://127.0.0.1:8080; } } Here are the relevant portions of my httpd.conf: Listen *:8080 ServerName <ip> <VirtualHost *:8080> ServerAdmin test@test DocumentRoot /var/www/html/wordpress ServerName domain.com </VirtualHost> This is what my nginx log loks like: <ip> - - [19/Jun/2012:22:35:35 +0400] "GET / HTTP/1.1" 301 0 "-" "Mozilla/5.0 This is what my httpd log looks like: 127.0.0.1 - - [19/Jun/2012:22:24:46 +0400] "GET /index.php HTTP/1.0" 301 - "-" -- WordPress Address (URL) and Site Address (URL) both have same http://domain.com

  Read the article

• Cisco IOS ACL: Don't permit incoming connections just because they are from port 80

  - by cjavapro

  I am going much based on my memory and I may not be correct on all of this. On a Cisco 851 (IOS) that uses a BVI or a bridge-route (the servers on the inside are configured with static and public IP addresses). I would apply two access lists (both end with deny ip any any log) on FastEthernet4 (the WAN port). There would be one for FA4 in and another for FA4 out. FA4 out would have a line like access-list 110 permit 98.76.54.0 0.0.0.255 gt 1023 any eq http I think this means from 98.76.54.* with a from port of at least 1024 can connect to any other machine with a destination port 80. So, then I have to allow the response to the HTTP connection. FA4 in would have a line like access-list 120 permit any eq http 98.76.54.0 0.0.0.255 gt 1023 Now the problem with that is that anybody on the outside can set their from port to port 80 and then connect to any inside port that is at least 1024. How do we prevent this and require the incoming data to be a response to the outgoing data.

  Read the article

• is there a man in the middle attacking to my server machine?

  - by GongT

  My server works well about half a year. But a strange thing happened (several hours before). This server has two IP-address 58.17.85.19 & 117.21.178.19 When I navigate to http://58.17.85.19, nothing different as before. But http://117.21.178.19 will return a "302 Object moved" and become a "redirect loop" I do some test: ($cmd = "wget http://117.21.178.19/?xx=$RANDOM --max-redirect 0 -S --no-cache -O -") Step by step: run $cmd on my PC and my firend's one (we live in two side of China, far away). - got 302 run $cmd on this server - got 200 OK (content is correct result of index.php) run $cmd on another server in same computer room - got 200 OK telnet from my PC and build an HTTP request (type by hand) - got 200 OK shutdown php-fpm, run $cmd on my PC - got 302 run $cmd on server - 502 Bad Gateway shutdown nginx, run $cmd on both the server and my PC - Connection refused. create iptables rule, refuse any connection to 58.17.85.19:80. run nc -l 80 -k -vvv on server and run $cmd on my PC NC show me that.... Server accept connection (Connection from [my ip]) My connection closed ! (Remove fd xx from list) wget dump out response - got 302 I know that, normaly, NC will accept connection, then dump HTTP request from client, and client will wait for response. this connection will open forever(infact client will close connection becouse timeout), becouse NC can't give any response. So... where my request gone? who send an response to the client? some virus on my server system? If so, why 58.17.85.19 didn't has this error? or... I was attacked by a middleman?

  Read the article

• Client cannot access my IIS7 web server

  - by Soccerwiz

  I have a Windows 2008 web server on running IIS 7 with about 25 websites. One of those sites is an SaaS application that is accessed constantly throughout the day. However, one particular client keeps getting blocked from my server. They will be using the service, and then all of a sudden they cannot access the program, or any other site on the server. The entire office of 4 users is blocked from accessing anything on the web server. A trace route reveals they get all the way to the server before they are blocked. However, they can access a linux server that is a different VM with a different IP on the same physical server. Also, when they are blocked from their office, they can still access the site from their mobile phone or local Starbucks. They can also occasionally reset the router and gain access to the web server again as they are on a dynamic IP address. I checked IIS and allow all IPs to access the server. There is nothing in the logs the says anything about a user being banned. I really have no idea what is causing this? Could it be a virus on their end? I have even moved the SaaS to a completely new server in a different location, and they were working fine for about a month, and then the problem started occurring again. Are there any hidden blacklists in IIS? Or is it a routing issue on their end?

  Read the article

• ddwrt client brigde acces point lost

  - by llazzaro

  Ok I have an AP with ddwrt firm (i know its not the best, but continue reading!) AP is configured to work like a wifi "transparent" brigde, also it had a virtual wifi network card to expand radius of wifi signal in that same AP. The brigde is working, computers behind AP gets ips from main routers which shares internet....BUT! I cant access webgui of the bridge AP... Main problem : AP is lost, but its working as brigde. I cant find it in the network (it didnt have any ip!) so I cant change any configuration... First solution : Reset AP, but it cannot be done. Reset button dont works due to a bug in ddwrt micro firm that mi linksys WAP54g had installed (I really hate this firmware I like more openwrt that my main router has) Second Solution : arp -a from main router , from computers behind AP...It dont appears in the list. Any more ideas, the router at some level must be there, the brigde is working. I know its possible that the AP is with an ip like 192.168.100.2 , my subnect actually is 172.16.X.X. :) thanks!

  Read the article

< Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >