Search Results

Search found 19408 results on 777 pages for 'output formats'.

Page 244/777 | < Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >

  • Blocking an IP from connecting

    - by Sam W.
    I have a problem with my Apache webserver where there's and IP than connecting to my server, using alot of connection and wont die which eventually making my webserver timeout. The connection will stay as SYN_SENT state if I check using netstat -netapu I even flush my iptables and use the basic rules and it still doesn't work. The IP will get connected when I start my Apache Basic rules that I use: iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT iptables -A INPUT -s 89.149.244.117 -j REJECT iptables -A OUTPUT -s 89.149.244.117 -j REJECT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A INPUT -p tcp --dport 21 -j ACCEPT iptables -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT iptables -A INPUT -j REJECT iptables -A FORWARD -j REJECT The bold part is rule in question. Not sure this is related but tcp_syncookies value is 1. Can someone point out my mistake? Is there a way to block it for good. Thank you

    Read the article

  • Wireless does not work on Ubuntu 9.04

    - by Yongwei Xing
    Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

    Read the article

  • unable to recover data from failed hdd

    - by Eslam Elyamany
    my hdd failing (or maybe totally dead) i've connected the hdd via USB but it doesn't appear in fdisk Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xe9fb38fb Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 40959999 20376576 7 HPFS/NTFS/exFAT /dev/sda4 40962046 976771071 467904513 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 82913280 86910975 1998848 82 Linux swap / Solaris /dev/sda6 86913024 394113023 153600000 7 HPFS/NTFS/exFAT /dev/sda7 40962048 82913279 20975616 83 Linux /dev/sda8 394122708 976768064 291322678+ 7 HPFS/NTFS/exFAT Partition 8 does not start on physical sector boundary. no sdc appears here , BUT it's appears on /dev/ rootghost-lap:/home/ghost# ls /dev/sd* /dev/sda /dev/sda2 /dev/sda5 /dev/sda8 /dev/sdb /dev/sdc1 /dev/sdc2 /dev/sdc6 /dev/sdc8 /dev/sda1 /dev/sda4 /dev/sda6 /dev/sda9 /dev/sdc /dev/sdc10 /dev/sdc5 /dev/sdc7 /dev/sdc9 also it appears in proc Code: rootghost-lap:/home/ghost# cat /proc/partitions major minor #blocks name 8 0 488386584 sda 8 1 102400 sda1 8 2 20376576 sda2 8 4 1 sda4 8 5 1998848 sda5 8 6 153600000 sda6 8 8 291322678 sda8 8 9 20975616 sda9 11 0 1048575 sr0 11 1 99136 sr1 8 32 244198583 sdc 8 33 14651248 sdc1 8 34 1 sdc2 8 37 15380480 sdc5 8 38 4153344 sdc6 8 39 48829536 sdc7 8 40 48829536 sdc8 8 41 110374551 sdc9 8 42 1975963 sdc10 and dmesg : [10604.777168] end_request: I/O error, dev sdc, sector 1 [10604.817238] sd 26:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [10604.817243] sd 26:0:0:0: [sdc] Sense Key : Aborted Command [current] [10604.817248] sd 26:0:0:0: [sdc] Add. Sense: No additional sense information [10604.817253] sd 26:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 02 00 00 06 00 ok now , let's see what i've tried testdisk to check for partitions -- failed dd to copy data from /dev/sdcX -- provide strange output size for example /dev/sdc1 is about 15G , the output for dd is 62G+ so i had to cancle it safecopy successfully made an image for partitons , but can't fix images, can't mount it, can't do any thing with it and some other tools i've tried and all failed , so any idea ?

    Read the article

  • Hard Disk Not Counting Reallocated Sectors

    - by MetaNova
    I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

    Read the article

  • iptables -- OK, **now** am I doing it right?

    - by Agvorth
    This is a follow up to a previous question where I asked whether my iptables config is correct. CentOS 5.3 system. Intended result: block everything except ping, ssh, Apache, and SSL. Based on xenoterracide's advice and the other responses to the question (thanks guys), I created this script: # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP Now when I list the rules I get... # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any anywhere anywhere state INVALID 9 612 ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:ssh 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:https 0 0 DROP all -- any any anywhere anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 5 packets, 644 bytes) pkts bytes target prot opt in out source destination I ran it and I can still log in, so that's good. Anyone notice anything major out of wack?

    Read the article

  • Can I use iptables on my Varnish server to forward HTTPS traffic to a specific server?

    - by Dylan Beattie
    We use Varnish as our front-end web cache and load balancer, so we have a Linux server in our development environment, running Varnish with some basic caching and load-balancing rules across a pair of Windows 2008 IIS web servers. We have a wildcard DNS rule that points *.development at this Varnish box, so we can browse http://www.mysite.com.development, http://www.othersite.com.development, etc. The problem is that since Varnish can't handle HTTPS traffic, we can't access https://www.mysite.com.development/ For dev/testing, we don't need any acceleration or load-balancing - all I need is to tell this box to act as a dumb proxy and forward any incoming requests on port 443 to a specific IIS server. I suspect iptables may offer a solution but it's been a long while since I wrote an iptables rule. Some initial hacking has got me as far as iptables -F iptables -A INPUT -p tcp -m tcp --sport 443 -j ACCEPT iptables -A OUTPUT -p tcp -m tcp --dport 443 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 443 -j DNAT --to 10.0.0.241:443 iptables -t nat -A POSTROUTING -p tcp -d 10.0.0.241 --dport 443 -j MASQUERADE iptables -A INPUT -j LOG --log-level 4 --log-prefix 'PreRouting ' iptables -A OUTPUT -j LOG --log-level 4 --log-prefix 'PostRouting ' iptables-save > /etc/iptables.rules (where 10.0.0.241 is the IIS box hosting the HTTPS website), but this doesn't appear to be working. To clarify - I realize there's security implications about HTTPS proxying/caching - all I'm looking for is completely transparent IP traffic forwarding. I don't need to decrypt, cache or inspect any of the packets; I just want anything on port 443 to flow through the Linux box to the IIS box behind it as though the Linux box wasn't even there. Any help gratefully received... EDIT: Included full iptables config script.

    Read the article

  • Mailgun Is Not Detecting My New MX Records

    - by Tyler Crompton
    When I issue a DiG command to verify my MX records, I get the following output: $ dig example.com MX ; <<>> DiG 9.9.5-3-Ubuntu <<>> example.com MX ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 47700 ;; flags: qr rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 5, ADDITIONAL: 5 ;; OPT PSEUDOSECTION: ; EDNS: version: 0, flags:; udp: 4096 ;; QUESTION SECTION: ;example.com. IN MX ;; ANSWER SECTION: example.com. 85468 IN MX 10 mxa.mailgun.org. example.com. 85468 IN MX 10 mxb.mailgun.org. ;; REMAINDER OF OUTPUT REMOVED FOR BREVITY However, when I click "Check DNS Records Now" on Mailgun, it verifies the changes to the TXT and CNAME records but says that my MX records have not been changed. Type | Priority | Enter This Value | Current Value -----+----------+------------------+-------------------- MX | 10 | mxa.mailgun.org | 10 mail.example.com MX | 10 | mxb.mailgun.org | 10 mail.example.com I updated these records three to fours ago. I know it said to wait up to twenty-four to forty-eight hours. But I feel that if it detected the other DNS changes, then it should detect the MX record changes. Am I being impatient or is this a legitimate concern? What do you suggest I do? Note: I'd create a Mailgun tag for this; I feel that it'd be appropriate, but I don't have enough reputation to do so.

    Read the article

  • Trouble with port 80 nating (XenServer to WebServer VM)

    - by Lain92
    I have a rent server running XenServer 6.2 I only have 1 public IP so i did some NAT to redirect ports 22 and 80 to my WebServer VM. I have a problem with the port 80 redirection. When i use this redirection, i can get in the WebServer's Apache but this server lose Web access. I get this kind of error : W: Failed to fetch http://http.debian.net/debian/dists/wheezy/main/source/Sources 404 Not Found [IP: 46.4.205.44 80] but i can ping anywhere. XenserverIP:80 redirected to 10.0.0.2:80 (WebServer). This is the port 80 redirection part of my XenServer iptables : -A PREROUTING -i xenbr1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 10.0.0 .2:80 -A INPUT -i xenbr1 -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT COMMIT What is wrong in my configuration? Is there a problem with XenServer? Thanks for your help ! Edit : Here is my iptables full content : *nat :PREROUTING ACCEPT [51:4060] :POSTROUTING ACCEPT [9:588] :OUTPUT ACCEPT [9:588] -A PREROUTING -p tcp -m tcp --dport 1234 -j DNAT --to-destination 10.0.0.2:22 -A PREROUTING -i xenbr1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 10.0.0 .2:80 -A POSTROUTING -s 10.0.0.0/255.255.255.0 -j MASQUERADE COMMIT *filter :INPUT ACCEPT [5434:4284996] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [5014:6004729] -A INPUT -i xenbr1 -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT COMMIT Update : I have a second server with 10.0.0.3 as IP and it has the same problem that 10.0.0.2 has.

    Read the article

  • User http does not have write permissions directory?

    - by dwieeb
    I have a bit of an odd set up, I think. I have groups for each domain my server hosts, and I add the user http to each domain group along with the users that should have access to the groups' domains. In my php script running from a directory 'public_html', I try creating a file: <?php $output = ""; print exec('touch test 2>&1', $output); But I get touch: cannot touch `test': Permission denied and the file is not created. But here, clearly stated, the group has all permissions on the directory: drwxrwxr-x 5 dwieeb example.com 1024 Feb 4 05:19 public_html And here are the permissions on the php file in public_html that is trying to use the exec function: -rw-rw-r-- 1 dwieeb example.com 59 Feb 4 05:19 test.php How is this possible if http is part of the example.com group (as seen from a cat on /etc/group) and the directory has full permissions for the group? ... example.com:x:1000:dwieeb,http I'm stumped. EDIT (since apparently I'm not cool enough to answer my own questions yet): Ah, I found the problem. Yes, I restarted Nginx, but the php-fpm daemon must be restarted as well when http is added to the group for my domain. On Arch Linux: rc.d restart php-fpm

    Read the article

  • Flash drive suddenly died. Why? Can I recover it?

    - by mg
    Hi, I have a flash drive that I used not too much but, after few month of inactivity, it died. I know that flash drives have a limited write cycles but I am sure that this is not the problem. I tried to create a new partition table and format the drive nothing worked. This is the output of mkfs.ext2. marco@pinguina:~$ sudo LANG=en.UTF-8 mkfs.ext2 -v -c /dev/sdc1 [sudo] password for marco: mke2fs 1.41.11 (14-Mar-2010) fs_types for mke2fs.conf resolution: 'ext2', 'default' Calling BLKDISCARD from 0 to 4001431552 failed. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 244320 inodes, 976912 blocks 48845 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=1002438656 30 block groups 32768 blocks per group, 32768 fragments per group 8144 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Running command: badblocks -b 4096 -X -s /dev/sdc1 976911 badblocks: Input/output error during ext2fs_sync_device Checking for bad blocks (read-only test): done Block 0 in primary superblock/group descriptor area bad. Blocks 0 through 2 must be good in order to build a filesystem. Aborting.... Is there something I can do to recover it?

    Read the article

  • Best grep-like tool

    - by e-satis
    I do in file search a lot, and used to love grep. Then I learn the existence of egrep, so I switched to benefit from the advanced regexp. Then I discovered the Eclipse search tool. Much easier to use that grep. Then I found ack : fast, easy, powerful. And now I use grin, which is smooth for pythonistas. I know there is also a couple of this kind of tools with a GUI. So what tool do you use, and why do you think it's the best. Practical features generally are : fast to fire and use; speedy processing; automatically ignore useless files; colored output; output lines, filename, context; allow complex regexp; allow a custom filtering and ouput; GUI + command line intergation; let you open an editor from the result set. There are some related posts on SO : http://stackoverflow.com/questions/87350/what-are-good-grep-tool-for-windows http://stackoverflow.com/questions/981601/colorized-grep-viewing-the-entire-file-with-highlighting http://stackoverflow.com/questions/1028107/is-there-some-unix-util-that-will-allow-me-to-grep-multiple-files-with-little-type http://stackoverflow.com/questions/1027906/unix-find-grep-syntax-vs-awk

    Read the article

  • Unable to mount root fs over NFS [on hold]

    - by johnmadrak
    I am attempting to set up a Raspberry Pi running Pidora to boot from an NFS share. My configuration in cmdline.txt is: dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/nfs nfsroot=<serverip>:/fake/path,nfsvers=3,rw,nolock nfsrootdebug ip=dhcp elevator=deadline rootwait On the Pi, the output I see is: IP-Config: Got DHCP answer from <router>, my address is <clientip> IP-Config: Complete: device=eth0, hwaddr=<macaddress>, ipaddr=<clientip>, mask=255.255.255.0, gw=<routerip> host=<clientip>, domain=, nis-domain=(none) bootserver=<routerip>, rootserver=<serverip>, rootpath= nameserver0=<routerip> (It pauses for a bit here) VFS: Unable to mount root fs via NFS, trying floppy VFS: Cannot open root device "nfs" or unknown-block(2,0); error -6 Please append a correct "root=" boot option; here are the available partitions: ..... On the NFS Server (an OpenVZ Container), the output I see in the /var/log/messages is: Aug 22 23:24:01 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:783 for /fake/path (/fake/path) Aug 22 23:24:38 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:741 for /fake/path (/fake/path) Aug 22 23:25:25 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:752 for /fake/path (/fake/path) Aug 22 23:26:12 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:876 for /fake/path (/fake/path) To test, I've made sure I can mount (non-root) from both the Pi and another machine and it worked. Does anyone have an idea on what could be wrong or how to narrow it down? Thank you in advanced for your help.

    Read the article

  • Fedora 15: em1 recently dissapeared and hostapd no longer serves internet to wirelessly connected devices

    - by Daniel K
    I have a laptop running hostapd, phpd, and mysql. This laptop uses an Ethernet connection to connect to the internet and acts as a wireless access point for my workplace's wifi devices. After installing some software and reconnecting my Ethernet elsewhere, my "em1" device is no longer present and wirelessly connected devices can no longer reach the internet. The software I recently installed is: pptp, pptpd, and updated some fedora libraries. I have also recently moved my desk and laptop to another location and thus had to reconnect the Ethernet elsewhere. Wifi devices no longer have access to the internet. Wirelessly connected devices are able to successfully log into the laptop, showing full strength, correct SSID, and uses the proper password. However, when I tried to connect to a site like google, the request times out. The device "em1" also no longer appears on my machine. Running: # ifup em1 will give me the following output: ERROR : [/etc/sysconfig/network-scripts/ifup-eth] Device em1 does not seem to be present, delaying initialization. And running: # dhclient em1 has the following output: Cannot find device "em1" When I run # dmesg|grep renamed, I get the following: renamed network interface eth0 to p4p1. I've tried to connect to the internet through p4p1 directly from the laptop and was successful. However, my wireless devices connected to my laptop are not able to connect to the internet. I have uninstalled pptp and pptpd using # yum erase ... but the problem still persists. To install pptp I used: # yum install pptp To install pptpd I did the following: # rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc15/pptp-release-current.noarch.rpm # yum install pptpd To update my fedora libraries I used: # yum check-update # yum update EDIT: Running # route produces the following results: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.11.200.1 0.0.0.0 UG 0 0 0 p4p1 10.11.200.0 * 255.255.252.0 U 0 0 0 p4p1 172.16.100.0 * 255.255.255.0 U 0 0 0 wlan0

    Read the article

  • CentOS 5 : error in installing php-imap

    - by TMMDev
    can someone please help me with this CentOS 5 question? I am trying to install php-imap, i tried yum install php-imap but I am getting the following output: Loaded plugins: fastestmirror, priorities, security Loading mirror speeds from cached hostfile * base: centos.hostingxtreme.com * epel: mirror.steadfast.net * extras: mirror.team-cymru.org * updates: mirror.beyondhosting.net Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package php-imap.x86_64 0:5.1.6-44.el5_10 set to be updated --> Processing Dependency: php-common = 5.1.6-44.el5_10 for package: php-imap --> Finished Dependency Resolution php-imap-5.1.6-44.el5_10.x86_64 from updates has depsolving problems --> Missing Dependency: php-common = 5.1.6-44.el5_10 is needed by package php-imap-5.1.6-44.el5_10.x86_64 (updates) Error: Missing Dependency: php-common = 5.1.6-44.el5_10 is needed by package php-imap-5.1.6-44.el5_10.x86_64 (updates) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest The program package-cleanup is found in the yum-utils package. I already have php-common installed, I ran "yum install php-common" and got the following output Loaded plugins: fastestmirror, priorities, security Loading mirror speeds from cached hostfile * base: centos.hostingxtreme.com * epel: mirror.steadfast.net * extras: mirror.team-cymru.org * updates: mirror.beyondhosting.net Setting up Install Process Package matching php-common-5.1.6-44.el5_10.x86_64 already installed. Checking for update. Nothing to do how can I fix this problem?

    Read the article

  • RouterLess, house-wired network using multiple powerline adapters

    - by Cliff Arnell
    related to the 'old days' of one ethernet cable tapped with Ts for each monitor.... my question might be very simple... or not. I have an over-the-air internet provider with a wire dish with a powered transceiver and cat5 cable out of the providers supplied modem. I'm presently connecting the output of the modem into my wireless router which sends the internet signal all over the house. Standard stuff, I believe. My Question. Can I just connect the output of the modem into 1 powerline adapter and tie all my equipment such as computer, printer, laptop, Tivo recorder, etc. into 1-each local powerline adapters located near each devices resulting in a 'house-wired' network and no router? I'm bothered by the idea that my over-the-air provider might be using something in my router to establish and keep my IP connection alive. I did have to configure the router for my IP, a router which, in my proposed scenario, would no longer exist. Thank you for your help.

    Read the article

  • What permissions do I need to move a folder?

    - by isme
    In the root of my drive there exists a folder called SourceControl that contains all the working copies of all my programming projects. I would like to move the folder to my user directory (\Users\Me), but something about the permissions on the folder forbids me. I don't remember how I created the folder. When I execute the move command: MOVE \SourceControl \Users\Me I receive the following error: Access is denied. I have resolved a similar problem in the past using the Takeown utility to assign ownership of the file to me, so I tried this command next: TAKEOWN /F \SourceControl It returns the following error: ERROR: The current logged on user does not have ownership privileges on the file (or folder) "C:\SourceControl". I've just learned about the Icacls utility, which can inspect and modify file permissions. I used this command to inspect the permissions on the folder: ICACLS \SourceControl It produced this list: \SourceControl BUILTIN\Administrators:(I)(F) BUILTIN\Administrators:(I)(OI)(CI)(IO)(F) NT AUTHORITY\SYSTEM:(I)(F) NT AUTHORITY\SYSTEM:(I)(OI)(CI)(IO)(F) BUILTIN\Users:(I)(OI)(CI)(RX) NT AUTHORITY\Authenticated Users:(I)(M) NT AUTHORITY\Authenticated Users:(I)(OI)(CI)(IO)(M) I think this means that normal user accounts, like mine, have permission only to read and execute (RX) here, while administrator accounts have full control (F). I used Icacls to confer full control of the directory to my user account with this command: ICACLS \SourceControl /grant:r Me:F The command produces this output: processed file: \SourceControl Successfully processed 1 files; Failed processing 0 files Now inspection of the permissions produces this output: \SourceControl Domain\Me:(F) BUILTIN\Administrators:(I)(F) BUILTIN\Administrators:(I)(OI)(CI)(IO)(F) NT AUTHORITY\SYSTEM:(I)(F) NT AUTHORITY\SYSTEM:(I)(OI)(CI)(IO)(F) BUILTIN\Users:(I)(OI)(CI)(RX) NT AUTHORITY\Authenticated Users:(I)(M) NT AUTHORITY\Authenticated Users:(I)(OI)(CI)(IO)(M) But after this the move command still fails with the same error. Is it possible to move this folder without invoking administrator rights? If not, how should I do it as administrator?

    Read the article

  • Gifsicle: How to set it to not overwrite the original GIF file if the resulting modified GIF file is larger than the original?

    - by galacticninja
    About Gifsicle: Gifsicle is a command-line tool for creating, editing, and getting information about GIF images and animations. One of its features is (from its website): Optimize your animations! This stores only the changed portion of each frame, and can radically shrink your GIFs. You can also use transparency to make them even smaller. Gifsicle’s optimizer is pretty powerful, and usually reduces animations to within a couple bytes of the best commercial optimizers. I call Gifsicle through this .BAT file in the Right Click - 'Send to' Menu: @echo off :compressFile "C:\Programs\Compression Scripts\gifsicle\bin\gifsicle.exe" --batch -V -O3 %1% echo. echo. SHIFT if exist %1% goto compressFile PAUSE This animated GIF file, however: http://i.minus.com/i7WdodY5Zwot3.gif, when its compression is optimized with Gifsicle with the above commands, results in a larger-filesized GIF file. Gifsicle overwrites the original GIF file with the resulting larger-filesized GIF file. Initial filesize: 7.57 MiB (7,942,886 bytes). After running through the above commands with Gifsicle: 7.64 MiB (8,017,622 bytes). Is there a way to prevent Gifsicle from overwriting the original file if its output file is larger than the original file, while still overwriting the original file if the output file is smaller? Details: OS: Windows 7 Gifsicle version: 1.63, from the binary provided here: http://www.lcdf.org/gifsicle/ Gifsicle manual

    Read the article

  • Slow tracepath on local LAN

    - by Simone Falcini
    I am on EXSi and I have 2 instances: Ubuntu and CentOS. These are the network configurations Ubuntu eth0 Link encap:Ethernet HWaddr 00:50:56:00:1f:68 inet addr:212.83.153.71 Bcast:212.83.153.71 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76059 errors:0 dropped:26 overruns:0 frame:0 TX packets:7224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6482760 (6.4 MB) TX bytes:2080684 (2.0 MB) eth1 Link encap:Ethernet HWaddr 00:0c:29:46:5a:f2 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:252 errors:0 dropped:0 overruns:0 frame:0 TX packets:608 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:42460 (42.4 KB) TX bytes:82474 (82.4 KB) /etc/iptables.conf *nat :PREROUTING ACCEPT [142:12571] :INPUT ACCEPT [5:1076] :OUTPUT ACCEPT [8:496] :POSTROUTING ACCEPT [8:496] -A POSTROUTING -s 192.168.1.0/24 -o eth0 -j MASQUERADE COMMIT *filter :INPUT ACCEPT [2:72] :FORWARD ACCEPT [4:336] :OUTPUT ACCEPT [6:328] -A INPUT -i eth1 -p tcp -j ACCEPT -A INPUT -i eth1 -p udp -j ACCEPT -A INPUT -i eth0 -p tcp --dport ssh -j ACCEPT COMMIT CentOS eth0 Link encap:Ethernet HWaddr 00:0C:29:74:1C:55 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe74:1c55/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:499 errors:0 dropped:0 overruns:0 frame:0 TX packets:475 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68326 (66.7 KiB) TX bytes:82641 (80.7 KiB) The main problem is that if i execute this command from the CentOS instance ssh 192.168.1.2 it takes more than 20s to connect. It seems like it's routing the connection to the wrong network. What could it be? Thanks!

    Read the article

  • Using udev to create a character device based on a driver being loaded

    - by SteveCB
    I'm in the process of setting up RAID monitoring for a number of Dell servers that use the PERC 6i integrated card. We're using Nagios at present and the check_megasasctl plugin seems to fit the bill. However, the plugin relies upon the existence of: /dev/megaraid_sas_ioctl_node This device node doesn't exist by default, you have to create it by hand using something like: mknod /dev/megaraid_sas_ioctl_node c 253 0 Now, to make the existence of this device node persistent across reboots, I thought I could write a udev rule, but as usual, I'm missing something. I thought I could create a file such as /etc/udev/rules.d/10-local/rules that contained: DRIVER=="megasas" NAME="megaraid_sas_ioctl_node" MODE="0600" But this doesn't work - no device node after a reboot. Dmesg output indicates the megasas driver is loaded and functional: megasas: 00.00.04.01-RH1 Thu July 10 09:41:51 PST 2008 megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0 megasas: FW now in Ready state Further, I don't see any means to instruct udev on which type of device node to create: character or block. I suspect I'm failing to understand exactly how udev is meant to work. I realise I could just cheat and run MegaCLI in /etc/rc.local, redirecting output to /dev/null; it creates the megaraid_sas_ioctl_node device node as part of its execution. I just thought using udev rules would be a) cleaner and b) a useful learning exercise. Perhaps I should just dump the above mknod command in /etc/rc.local... So how do I get udev to create the /dev/megaraid_sas_ioctl_node device node based on the presence of the megasas driver? Cheers Steve

    Read the article

  • SWATCH - what am I doing wrong?

    - by Brian Dunbar
    What I want/need/desire is to log when a user logs into my FTP server. Problem: I can't make swatch work the way I should be able to. This data is logged to a file - but of course these logs are not kept very long. I can't keep the logs around forever, but I can extract data from then, analyze it, store results elsewhere. If there is a better way to do this than the following, I'm all ears. Swatch version 3.2.3 Perl 5.12 FTP: VSFTP OS (Test): OS X 10.6.8 OS (Production): Solaris From man I see I can pass contents to a command .. so I should be able to echo those values to file, do a sed/cut/uniq thing on them for stats. $ man swatch (snip) exec command Execute command. The command may contain variables which are substituted with fields from the matched line. A $N will be replaced by the Nth field in the line. A $0 or $* will be replaced by the entire line. Swatch file .swatchrc watchfor /OK LOGIN/ echo=red pipe "echo "0: $0 1:$1 2:$2 3:$3 4:$4 5:$5" >> /Users/bdunbar/dev/ftplog/output.txt" Launch with $ swatch -c /Users/bdunbar/.swatchrc --script-dir /Users/bdunbar/dev/ftplog -t /Users/bdunbar/dev/ftplog/vsftpd.log & Test echo "Mon July 9 03:11:07 2012 [pid 14938] [aetech] OK LOGIN: Client "206.209.255.227"" >> vsftpd.log Results - it's echoing to TTY. This is not needed or desired on the server, but it does tell me things are working. ftplog *** swatch version 3.2.3 (pid:25780) started at Mon Jul 9 15:23:33 CDT 2012 Mon July 9 03:11:07 2012 [pid 14938] [aetech] OK LOGIN: Client 206.209.255.227 Results - bad! I appear to not be sending the variables to text. $ tail -f output.txt 0: /Users/bdunbar/dev/ftplog/.swatch_script.25780 1: 2: 3: 4: 5:

    Read the article

  • Manual NAT on Checkpoint (Redirect all http requests to a local web server)

    - by B. Kulakli
    We have a proxy server in our internal network and I want to redirect all internet http requests to a web server in local network. It'll be like a Network Billboard that says "No direct connection is available. Set up your proxy etc." For example: A user starts the computer Opens the browser Tries to open www.google.com Should see web server output on local network Tries another web site on internet Should see web server output on local network Sets up proxy Tries to connect to a web site Web site should be loaded I have added a simple manual NAT rule to address translation in Checkpoint firewall but it simply does not work. Here is my address translation rule Source Destination Service T.Source T.Destination T.Service MY_PC A_GOOGLE_IP ALL ORIGINAL INT_WEB_SRV ORIGINAL Then when I ping A_GOOGLE_IP, replies come from INT_WEB_SRV, as I expected. However, when I try to connect A_GOOGLE_IP from browser (http://A_GOOGLE_IP), no replies come from SYN_SENT and falls into timeout. When I look at the firewall log of INT_WEB_SRV, I can see the incoming connection requests from MY_PC is accepted and NO denies. By the way, there is no problem to see INT_WEB_SRV (http://INT_WEB_SRV) from browser. My understanding is, my NAT rule at checkpoint NGX R60 does not include return packets. I definitely need some help.

    Read the article

  • Linux Cups raspberry pi offload processing to server

    - by jaredmsaul
    I am interested in setting up a raspberry pi as the local end of a printing solution. In my testing the pi chokes on acting as a complete cups based print server. It seems a little underpowered for some of the ghostscipt processing and other filtering that occurs-- particularly on larger or complex documents the processing time can be 5 or more minutes. My question is can the processing be largely done elsewhere and the prepared end product of the processing chain be fed to the pi for output on the connected printer? So in this scenario any arbitrary document (html, pdf, text) is initially 'printed' on a relatively powerful machine but the output is stored in a file. This file is then grabbed by the pi and with all the heavy work out of the way easily printed using cups. I know files can be pushed through cups in raw mode but I am fuzzy on the pros and cons and the applicability in what I describe. I have tested this with pdftops creating a ps file then feeding that raw to cups and I think it works but it seems like there may be a cleaner solution. This scenario would ideally work for any number of printer types.

    Read the article

  • Finding default gateway in an openvpn environment in windows

    - by Alexander Trümper
    I need to find the default gateway in a openvpn scenario where the route output looks like that: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.49.73.1 10.49.73.24 10 0.0.0.0 128.0.0.0 10.8.0.1 10.8.0.2 30 So I googled around a bit and a found this script here: @For /f "tokens=3" %%* in ( 'route.exe print ^|findstr "\<0.0.0.0\>"' ) Do @Set "DefaultGateway=%%*" echo %DefaultGateway% This works, but matches both lines in the route output. But I need to find this line: 0.0.0.0 0.0.0.0 10.49.73.1 10.49.73.24 10 So I tried to modify the findstr parameter like this: findstr "\<0.0.0.0\>.\<0.0.0.0\>" in the expectation that '.' will match for the tab between the columns. But it doesn't. It will still set DefaultGateway to 10.8.0.1 I couldn't find a clue in MS documentation either. Maybe someone knows the right expression? Thanks a lot.

    Read the article

  • Run GUI application via cronjob in Ubuntu?

    - by Christoffer
    Hi, I have a remote server running "Ubuntu 10.04 Desktop". From it I want to run a script that walks through a list of websites and captures screenshots of them. The script is working and thoroughly tested. When I SSH to the server with ssh -X user@ip-adress I can run my script by calling ./myscript.py and everything will work OK. I then modifed my crontab file and added... 59 17 * * * env DISPLAY=:0 /path/to/myscript.py ...as recommended by the Ubuntu WIKI. I can see in the /var/log/syslog that my cron job is started, but it doesn't capture any screenshots. When running env DISPLAY=:0 /path/to/myscript.py from the shell I get No protocol specified myscript.py: cannot connect to X server :0 If I ssh to the server without the -X option I only get the second row of the error: myscript.py: cannot connect to X server :0 What can I try now? More details I have run xhost +local: and checked the output of xhost to see that the option was set correctly. If I run ls /tmp/.X11-unix/ the output is X0 The server only has one screen. Thank you in advance!

    Read the article

  • Imagemagick convert with resample option

    - by coneybeare
    I am creating thumbnails from much larger images and have been using this command successfully for some time: convert FILE -resize "64x" -crop "64x64+0+16" +repage -strip OUTFILE I also do some other processing that is not relevant to the question. I realized that this does not adjust the resolution at all, so if I use a 300dpi image, it ends up displaying really small on some devices. I want to resample it to 72x72 so I have been trying with this command: convert FILE -resize "64x" -crop "64x64+0+16" +repage -strip -resample 72x72 OUTFILE And expected the 64x64 image at 300dpi to be resampled to a 64x64 image at 72dpi, but instead, I am getting a very funny size and density. Here is "identify" output for the original and post-processed file WITHOUT the resample: coneybeare $ convert "aa.jpg" -crop "64x64+0+16" +repage -strip "aa.png" coneybeare $ for image in `find . -type f`; do identify $image; identify -verbose $image | egrep "^ Resolution"; done ./aa.jpg JPEG 1130x1695 1130x1695+0+0 8-bit DirectClass 1.492MiB 0.000u 0:00.000 Resolution: 300x300 ./aa.png PNG 64x64 64x64+0+0 8-bit DirectClass 7.46KiB 0.000u 0:00.000 Resolution: 118.11x118.11 And here is the "identify output for the command WITH the resample: coneybeare $ convert "aa.jpg" -crop "64x64+0+16" +repage -strip -resample 72x72 "aa.png" coneybeare $ for image in `find . -type f`; do identify $image; identify -verbose $image | egrep "^ Resolution"; done ./aa.jpg JPEG 1130x1695 1130x1695+0+0 8-bit DirectClass 1.492MiB 0.000u 0:00.000 Resolution: 300x300 ./aa.png PNG 15x15 15x15+0+0 8-bit DirectClass 901b 0.000u 0:00.000 Resolution: 28.34x28.34 So, the question is: What am I doing wrong and how can I fix it so the end result is a 64x64 cropped thumbnail image at 72dpi?

    Read the article

< Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >