Search Results

Search found 6660 results on 267 pages for 'usb recognition'.

Page 250/267 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

• Choice of filesystem for GNU/Linux on an SD card

  - by gspr

  Hi. I have am embedded ARM-based system running on an SD card. It's currently Debian GNU/Linux using ext3 as filesystem. As I'm about to reinstall the system, I started wondering about changing to a more flash-friendly filesystem. I've heard about JFFS2, YAFFS2 and LogFS, and they all seem suited to the job. Which one would you recommend? Also, I've heard there have been a lot of ext4 improvements to better suit SSD disks; am I to interpret that as running ext4 should be just fine? What do I need to think especially about in that case? I guess the usage of the system is important. But for the sake of generality, imagine it'll do standard desktop stuff (even though it is infact a small ARM-based system). Thanks for any replies. Edit: Wikipedia tells me (in a "citation needed" statement) that Removable flash memory cards and USB flash drives have built-in controllers to perform wear leveling and error correction so use of a specific flash file system does not add any benefit. Thus, I'm leaning towards sticking with an ext filesystem.

  Read the article

• Alfa AWUSO36H 1W dysfunctional driver

  - by BrainStorm

  I recently purchased an Alfa AWUSO36H 1W wireless USB adapter for my notebook, in order to improve signal strength and quality. I'm currently using Linux Mint 11, and the it uses the RTL8187 driver for this adapter, I'm also using a 4dbi antenna, though I have others. The problem is that this adapter does exactly the opposite of what it should, actually my internal Broadcom BCM4313 adapter works way better than the alfa. Browsing is slow, some network applications don't even work, pings against Google.com on the internal adapter runs smooth, while in the alfa it gets like 25% packets lost or more! I'm less them 50 feet from my AP, the internal adapter gets 44/70 link quality, and the alfa gets around 60/70 (iwconfig output). Also the system always sets alfa power to 20dbm(100mw), then I have to do sudo iw set reg B0 to make it 30dbm(1000mw), but apparently no significant change. I've installed wireless-compat drivers, no change either. And worst of all, in Windows 7 it works way more smoothly for browsing, though I couldn't test it properly there. I hope its a driver problem, even if it's a pain to find/compile Linux drivers for a starter, I prefer it to a hardware problem where I would need to buy another adapter, since I have no money left (except for the cantenna pieces).

  Read the article

• Ubuntu+Win7--disk error press any key to restart

  - by Siddharth

  Apparently,none of the solutions in any other posts and forums worked for me For some reasons I decided to remove ubuntu from my hard disk drive. My partition table(presently): (/dev/sda1) (fat32) 900 MiB ---(MBR,I suppose) (/dev/sda2) (ntfs) 70 GiB -----(Windows 7) (/dev/sda3) (ntfs) 314.88 GiB --(Personal File storage) (/dev/sda4) (ext4) 80 GiB -----(Ubuntu 13.04) (unallocated) -----1.31 MiB So,after moving(cut-paste) everything(for backup) from the fat32 partition using win7..I booted into Ubuntu and copied the remaining 3 files(hidden in Win7 file explorer) --bootmgr,bootsect.bak,and one more which I do not remember.TERRIBLE MISTAKE After this I again booted into Windows and deleted ext4 partition..formatted it to ntfs..and shut down the pc.Then,I put in a Win7 bootable USB..using command prompt I entered bootrec /fixmbr,and bootrec /fixboot.. Restarting showed me the GRUB..choosing windows 7 showed me "Disk Error. Press any key to restart." I also installed a fresh Win7 installation on the 80 GiB partition expecting a Windows Legacy Bootloader with two win7 options..but did not work. Then..I used a Ubuntu LiveUSB to put it back to the present configuration(above) since all methods to restore the MBR failed.. I copied back the fat32 partitions backup files but couldn't copy those 3 files.Somehow ,they had been recreated and were non-replaceable. I do not want to format the win7 partition for a fresh one. I have used boot-repair..Restore MBR option brings back to "Disk error...." without even going through grub..so I reinstalled grub and I'm able to boot into Ubuntu. grub menu shows the win7 option as "Windows 7 (loader) (on /dev/sda1)". paste.ubuntu.com/5753710 paste.ubuntu.com/5775999

  Read the article

• How to minimize the risk of employees spreading critical information?

  - by Industrial

  Hi everyone, What's common sense when it comes to minimising the risk of employees spreading critical information to rivalling companies? As of today, it's clear that not even the US government and military can be sure that their data stays safely within their doors. Thereby I understand that my question probably instead should be written as "What is common sense to make it harder for employees to spread business critical information?" If anyone would want to spread information, they will find a way. That's the way life work and always has. If we make the scenario a bit more realistic by narrowing our workforce by assuming we only have regular John Does onboard and not Linux-loving sysadmins , what should be good precautions to at least make it harder for the employees to send business-critical information to the competition? As far as I can tell, there's a few obvious solutions that clearly has both pros and cons: Block services such as Dropbox and similar, preventing anyone to send gigabytes of data through the wire. Ensure that only files below a set size can be sent as email (?) Setup VLANs between departments to make it harder for kleptomaniacs and curious people to snoop around. Plug all removable media units - CD/DVD, Floppy drives and USB Make sure that no configurations to hardware can be made (?) Monitor network traffic for non-linear events (how?) What is realistic to do in a real world? How does big companies handle this? Sure, we can take the former employer to court and sue, but by then the damage has already been caused... Thanks a lot

  Read the article

• External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

  - by tom

  Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

  Read the article

• Custom PCI bracket with support, for custom PCB?

  - by newbiez

  I am considering to put a custom PCB card that I made, into my computer. It won't go on any PCI connector, it plugs in on a USB connector on the motherboard, via a ribbon cable. I need thou to plug a device to it; which means that either I leave the PCB outside the case, hanging by the ribbon (bad idea), or I could put it in a PCI slot, using a bracket. The issue is that the brackets that I have, do not have tabs, so I have no way to screw the PCB on them. I was hoping to find something that would allow me to put the PCB on it, and then just fit it in the PCI bracket opening, like this: http://www.idotpc.com/TheStore/pc/viewPrd.asp?idproduct=1203&idcategory=0 This one won't fit the bill since the holes are too close apart, compared to the one that I have already on the PCB (and can't make more holes). Do you know if there is a place where they make universal PCI bracket mounting systems for custom PCB? I just need one, so can't even order a custom one (they ask me 120 dollars for one). Thanks in advance!

  Read the article

• Can't mount hard drive. Ubuntu 12.04

  - by Sam

  I am trying to recover some pictures on my 320 GB Hard Disk, so I put in a Live Ubuntu CD and am in that right now. In the devices list, it shows my USB drive, but not my 320 GB Hard Disk. I can see the disk in Disk Utility (it says it's on /dev/sda), but it's not mounted, and it says it has a few bad sectors but it is OK. In Disk Usage Analyzer, it says my maximum capacity is 13.4 GB, so it's definitely not using the 320 GB Hard Disk. I tried the following: sudo mkdir /media/newhd (worked) sudo mount /dev/sda /media/newhd (didn't work. it says I must specify the filesystem type) I then tried: fsck.ext4 -f /dev/sda (didn't work. Said: Superblock invalid, trying to backup blocks. then: Bad magic number in super-block while trying to open /dev/sda. The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock) Does anyone have any ideas? The whole problem started when my Windows Vista said "Can't find operating system". Any ideas on how I can get on to my hard drive at /dev/sda?

  Read the article

• Automatic o/s reset on a dedicated internet browsing Windows 7 pc.

  - by camelCase

  I have just purchased a new Acer Revo nettop PC for dedicated internet browsing. It will be the only pc on a home network. My original plan was to install one virtual PC for family browsing, another for remote web based server administration and ban browser use from the host Windows 7 o/s. The idea was that I could recover to a fresh VHD image once a week to eliminate any build up of malware inside the browser VMs. However now I am looking for alternative solutions since the Intel Atom cpu does not have hardware VT support which Windows Virtual PC requires. Would it be possible to engineer some type of routine overnight host o/s wipe and recovery? I guess cyber cafes do something like this? The only user data that would need to be retained across a recovery would be browser bookmarks but these could be exported to remote service. Edit 1: I am thinking the o/s reset could be done via some disk image recovery process. Edit 2: Just had a brainwave. Routine browsing could be done via the new Google Chrome O/S. I have just seen a video of the Google Chrome o/s booting off a usb pen drive in seconds.

  Read the article

• computer freezes but music continues

  - by Danny

  Recently I have had a problem where my computer will freeze completely but if I happen to be streaming Pandora in a tab that will continue playing. If I wait about 2-5 minutes it will eventually come back and start working normally. I also noticed that during the period that it is unresponsive that the HDD activity light stays lit the whole time, not flashing. I've ran memtest86+ and a diagnostic from Western Digital for my HDD model and none of them reported any errors. The specs for my computer are 1 x ASRock H55M/USB3 R2.0 LGA 1156 Intel H55 HDMI USB 3.0 Micro ATX Intel Motherboard 1 x CORSAIR Enthusiast Series CMPSU-550VX 550W ATX12V V2.2 SLI Ready CrossFire Ready 80 PLUS Certified Active PFC Compatible with Core i7 Power Supply 1 x Intel Core i3-540 Clarkdale 3.06GHz LGA 1156 73W Dual-Core Desktop Processor Intel HD Graphics BX80616I3540 1 x G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ 1 x ASUS PCE-N13 PCI Express 150/300Mbps Transfer/Receive Rate Wireless Adapter 1 x EVGA 01G-P3-1556-KR GeForce GTX 550 Ti (Fermi) FPB 1GB 192-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card I can't imagine what would be causing these problems.

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

• Windows 7 explorer crashing trying to read external hard disk

  - by Mario De Schaepmeester

  I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

  Read the article

• Recover badly recorded DVDs

  - by CesarGon

  A few years ago (2003-2005) I bought a Sony USB external DVD recorder for my Dell laptop and I used it to burn a lot of discs. Much later, when I tried to use one of these discs, I realised that I could not read it. The disc behaved as if it was scratched or dirty. I tried on a couple of different DVD drives but got the same effect. Sadly, all the discs that I burnt with that recorder suffer from the same problem. Edit. When I read one of these discs with ImgBurn, I get lots of unrecovered read errors in multiple sectors, even at 1x speed. The sectors that cause read errors seem to be quite random; it's not always the same one. I have no idea what could be wrong with the discs. I doubt that they are scratched or dirty; it would be too much of a coincidence that all the discs that I burnt with that recorder got damaged at the same time. Also, they don't show any physical defects. Is there any way to diagnose what the problem is and, hopefully, recover the contents of the discs? Many thanks.

  Read the article

• Is it safe to force a dismount to format a volume in Windows?

  - by sammyg

  I am using format command in cmd to format a USB flash drive. M:\>format /FS:FAT32 /Q Required parameter missing - M:\>format M: /FS:FAT32 /Q Insert new disk for drive M: and press ENTER when ready... The type of the file system is FAT32. QuickFormatting 14999M Format cannot run because the volume is in use by another process. Format may run if this volume is dismounted first. ALL OPENED HANDLES TO THIS VOLUME WOULD THEN BE INVALID. Would you like to force a dismount on this volume? (Y/N) y Volume dismounted. All opened handles to this volume are now invalid. Initializing the File Allocation Table (FAT)... Volume label (11 characters, ENTER for none)? Format complete. 14,6 GB total disk space. 14,6 GB are available. 8 192 bytes in each allocation unit. 1 917 823 allocation units available on disk. 32 bits in each FAT entry. Volume Serial Number is E00B-2739 M:\> Is it safe to force a dismount like this, and make the handles invalid?

  Read the article

• Laptop seemingly randomly "freezes" to the point of no longer executing applications

  - by Aierou

  After upgrading to Windows 8 pro on my Samsung Series 7 Chronos NP700Z5C-S04US (may be relevant, I'm not sure), my computer began to stop allowing the execution of any service or application, as well as discontinuing the update of the clock until a hard shutdown was performed. This seems to occur randomly after periods of inactivity and I've no idea the cause. These are measures I have already taken in order to attempt to stop this: -Obviously Googling potential answers to this problem -Updating all drivers -Researching all events that have occurred around the time of the failure to respond (with no results) -I tried applying "bcdedit /set disabledynamictick no" which was a hotfix for what seemed to be the same error but was not. Here is some more, potentially related, information about the error: -No BSOD (actually, I haven't at all experienced a BSOD with Windows 8) -Computer seems to have a problem shutting down/restarting most of the time (Hangs at the point where it should completely turn off) -New sound instances are not able to play, but previously loaded containers function properly -As mentioned before, the clock freezes at the time of the error -USB devices function properly -Servers that I was running fail to respond on my end, but stay online. If you require more information, please request it specifically and I will be happy to oblige. Thanks.

  Read the article

• mouse pointer moving on its own

  - by PA

  After two months of working correctly, I am experiencing an strange and very annoying problem. My mouse pointer is moving on its own. If I move the mouse to the left, as soon as I stop the movement, the pointer runs again to the far right. This makes the mouse totally unusable. The mouse device is an optical USB mouse. It is not a problem with the mouse itself. I have tried with another mouse, same problem. (both mice are OK, I have tried both mice on my laptop, both worked perfectly) Have tried different surfaces, too. Same problem. System is Windows XP Pro SP3. Computer is a desktop PC two months old. I suspected it could be a problem with the mouse driver. But both mice are from different brand, so I suppose they use different drivers. What else can I try? any suggestion?

  Read the article

• Running WAMP (XAMPP) and LAMP from One SSD, On 64-bit Windows and Linux Machines

  - by nicorellius

  I have an solid state drive that I develop websites on. The reason I do this is because I work on a few different computers. Historically, I created separate developing environments to use for each machine. This was OK, but if the system changed for some reason, eg, new OS install, it was a pain. So I bought a USB 3.0 enclosure and put a solid state drive in there and it's pretty darn fast, which is good. I was working with three Windows machines and I could simply hook up the drive, launch my XAMPP server and away I went, developing websites: using Dreamweaver, Komodo, Notepad++, Eclipse, etc. Recently, however, one of my Windows machines' hard drive went down and instead of going back to Windows in this case, I went with Ububntu 12.04. I have several Ubuntu workstations and servers and I like Linux, so I thought his was a great opportunity to transition. I went to work installing and trying to set up a LAMP server and, besides from XAMPP 64-bit compatibility out of the box, I'm seeing other issues with getting this Linux server running. I will keep trying to resolve this, but in the meantime... my question is, has anyone ever successfully run both WAMP and LAMP from the same SSD (formatted to NTFS)? I'm sure there are lots of barriers to this happening, like local file system, OS libraries, dependencies, etc. But I was thinking it would be cool if it could be done. I'm no expert, so if this is just plain old stupid, please don't hesitate to let me know.

  Read the article

• Need help toubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

  Read the article

• What diagnostics are safe to run on an SSD drive?

  - by Peter Mounce

  I have a MacBook Pro (late 2010) with a Crucial RealSSD 256Gb in it; 60Gb is given to the Windows 7 x64 BootCamp partition. I have a USB-attached 500Gb drive for (most) data. In the last day or so, I've had a BSOD and several OS freezes (both Mac OSX 10.6.6 and Win7). The system in both cases will boot fine (at the moment!) and then run things fine, then some time later a program will stop responding, followed shortly thereafter by the system as a whole, forcing a reboot. This smacks to me of a storage problem. Given that I have an SSD and not a regular magnetic HDD, what are my next steps, in both OS'? I haven't seen anything pertinent in Windows' event-log. I'm not sure of the equivalent place to look in OSX; it's never given me issue to find out. What are my options for attempting to save my data from the SSD to another drive, given that after some small amount of time (eg half an hour), the OS stops responding? What are the recommended next steps?

  Read the article

• Did my hard drive fail or is it something else?

  - by Julian

  Last night while I was watched a movie on my laptop the external monitor just went blank and the built-in display froze. Weird I thought, so I restarted it only to be greeted with this heart-breaking message. "No Operating System Found". After a few panicked restarts I accepted the fact that my hard drive might be done :(. Being the resourceful technie that I am, I whipped out Ubuntu Live on my old Flash Drive and was up and running before day break. I cannot access the hard drive through Ubuntu (which I expected) but I also cannot access my DVD drive either! This got me thinking that it might not be the hard drive and some other component that they hdd and the dvd uses. Hopefully this is the case. Which component is the most likely culprit? What tools can I use from Ubuntu Live on my USB flash drive to find out? I'm in a bad place without my hdd, thanks in advance for any assistance provided! P.S. My laptop makes a weird noise when I try to access or eject my DVD within the slot. Also my HDD makes a weird noise sometimes. Not sure how to describe it. System Specs: Dell 1558

  Read the article

• Windows 7 - ignore security when reading external drive

  - by w-

  hi, My system hard drive on an XP computer kind of failed (random corrupt sectors). So i got a new harddrive and am trying to recover the files. The filesystem is NTFS. The system i'm trying to use when recovering the files is Windows 7. I'm obviously an admin on this box. The last data i'm trying to recover is stuff in the Documents and Settings folder. I'm using a SATA to a USB cable thingy so that I just plug it in as an External Hard Drive. The problem: In Windows Explorer when i try to copy the data, I keep getting prompted with Security warnings and error messages. It keeps telling me i have to change the owner permissions of the folder and all it's contents. If i tell it to change all the files and folder permissions it takes a really long time because it has to recurse through all the folder contents to change the permissions. Is there a way for me to ignore the file permissions when doing this? thanks

  Read the article

• How can I make a copy of a printer in Win7?

  - by hawbsl

  Has anyone been able to copy an existing printer in Win7? I know that we were able to do this in XP (not as a direct copy/paste, but by installing the printer twice) but in Win7 it doesn't seem to be possible. Googling the answer is hopeless because searching for "copy printer" or "duplicate printer" you get a bunch of posts about "printer copiers" or people complaining about duplicate printers getting created in the background (precisely what I'd like to be able to do) It'd be good to know how to do it in general, but if it depends on the printer type, then in our case we are trying to make a copy of an HP Laserjet. Tried installing from the CD - but the CD is too old for Win7 Tried installing via Add Printer and that seems to install the printer but it's marked with an error. Tried installing via the .exe installer from the HP site and that does result in a successful printer being installed, but it won't let you install the same printer twice (stalls on the "insert USB cable now" step - simply won't enable the greyed out "Next" button). The reason this is required is so that we can print to one to the feeder and to the tray separately.

  Read the article

• wireless to wired internet

  - by Mark T

  My wife uses an old computer which doesn't really like having an internet connection via a USB wireless adapter. I've tried several, and none have been satisfactory. The connection gets dropped often and it is frustrating for her. A wireless card also had the same trouble. Repositioning the computer made no difference. (Two laptops, nearby, connect just fine and stay up, so it isn't the router.) However, the computer always worked well when I had an Ethernet cable connected to it. I know there is a box which will connect to my wireless network and provide an Ethernet cable connection. But the terminology used is so complex, I can't tell what it is I really need. In case that wasn't clear, here it is in different words: What I need is just the opposite of a wireless router. My wireless router takes my cable modem's Ethernet connection and makes it available to wireless clients. What I want is a box which is a wireless client to my wireless router and provides an Ethernet cable connection that I can connect to any device. I need to know the right name for a box with such capabilities. If you know of some inexpensive examples, that would also be helpful. I'm running a wireless G network with a Linksys Router.

  Read the article

• How to set up Windows 7 Professional as a NAS

  - by Enyalius

  I searched and didn't find any answers, so please forgive me if this is a repeat. Anyway, I have an older computer that I'm using as an HTPC, and I was hoping that I could use it as a NAS/multimedia server, as well. My primary uses would include accessing content on my PS3 (same LAN), accessing content from other computers on my home network and (if I can) accessing content from my Android phone over the internet. I have used SubSonic to stream music to my Android phone and other computers before, but I would really like to find a way to do this natively if possible. I know that I can buy external hard disk cases that can plug in the USB port of my router, that I can get a Drobo or other network storage solution, but I would really just rather not spend the money (especially considering that I already have a computer that I should be able to use). Hardware involved: Apple AirPort Extreme base station router (most recent revision) Home Theater Personal Computer: Core 2 Duo @ 2.4GHz, 8GB DDR2 RAM, ~3.5TB hard drive space Sony Playstaiton 3 Thin 120GB HTC Thunderbolt (I have 4G coverage) rooted and running Android 2.2.1 Various Apple laptops Various Windows 7 desktops/laptops Thanks in advance! Note- I have looked at open source NAS software but I would like to preserve the Windows Media Center functionality in Windows 7, so other NAS software is not an option for me currently. .

  Read the article

• How to fix a damaged/corrupted NTFS filesystem/partition without losing the data on it?

  - by Gareth

  I was going to install Fedora 15 along side my Windows 7 Starter on my Acer Apire One D255E and at some point during the resizing of the NTFS partition (the one with Windows on it) the setup failed. Now I cannot access this partition from any OS. When I tried to access it from a Fedora install running on a USB flashdrive I get this error: Error mounting: mount exited with exit code 12: Failed to read last sector (452534271): Invalid argument HINTS: Either the volume is a RAID/LDM but it wasn't setup yet, or it was not setup correctly (e.g. by not using mdadm --build ...), or a wrong device is tried to be mounted, or the partition table is corrupt (partition is smaller than NTFS), or the NTFS boot sector is corrupt (NTFS size is not valid). Failed to mount '/dev/sda5': Invalid argument The device '/dev/sda5' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? It doesn't make a lot of sense to me but I was really hoping it would to someone and they can give me a way to restore the partition without losing everything on it (I have a lot of important notes from various classes on there)? Cheers.

  Read the article

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >