Search Results

Search found 183740 results on 7350 pages for '404 not found'.

Page 254/7350 | < Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >

• Mod_rewrite not working on ISPConfig 3 Server

  - by Akahadaka

  Problem I recently migrated a Drupal site from a shared hosting server to my own VM. Everything appears to work correctly, except clean urls. My VM Setup Ubuntu 10.04 LAMP ISPConfig 3 What I've tried From reading up on a number of drupal forums I've tried the following in this order Check that mod_rewrite is installed and enabled Changed PHP from FastCGI to Mod_PHP (prefer to use FastCGI or suPHP though to avoid having tmp/files folders with 777 permissions) Changed the Redirect type to L in ISPConfig Sites-domain.com-Redirect Changed /etc/apache2/sites-enabled/000-default <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All ... </Directory> Not sure about points 3 and 4, I do want all domains to be able to use mod_rewrite out of the box. Question Have I done something wrong or am I missing a step? Ultimately I would like to use FastCGI and clean urls working on all ISPConfig 3 domains without having to make any changes to individual domain settings. Any ideas appreciated, I'll try them all.

  Read the article

• CentOS: eth0 not starting on boot

  - by Cameron Aziz

  Whenever I reboot a CentOS Hyper-V VM, eth0 does not start automatically. All I need to do is perform ifup eth0 and all is fixed, but that isn't feasible from ssh! I am starting in runlevel 3. After I perform ifup eth0 on the console: [root@localhost ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:5D:2B:2B:07 inet addr:10.10.0.3 Bcast:10.10.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe2b:2b07/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4656 (4.5 KiB) TX bytes:6399 (6.2 KiB) Interrupt:9 Base address:0xa000 [root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=10.10.0.3 NETMASK=255.255.255.0 GATEWAY=10.10.0.1 USERCTL=no ONBOOT=yes [root@localhost ~]# chkconfig --list | grep network network 0:off 1:off 2:on 3:on 4:on 5:on 6:off

  Read the article

• UIWebViewNavigationTypeLinkClicked event not getting fired for certain links

  - by userlite

  Hi, I am using a UIWebView as an embedded browser within my iphone app. I am using the shouldStartLoadWithRequest function to handle UIWebViewNavigationTypeLinkClicked events for links clicked by a user. It is working as expected for a number of sites, but not for all. For example: when I click on any of the links on website http://www.foxnews.mobi, the UIWebViewNavigationTypeLinkClicked event is not getting fired. Same thing happens for some other sites. I read somewhere that links with blank target do not fire the event, however this is not the cause of the problem in my case. Any help is appreciated. Thanks.

  Read the article

• Laptop not charging when connected to mains outlet

  - by Josh

  I've had this laptop for a few weeks now, it's a Sony Vaio. I went to charge it a few days ago and plugged in the power cable, but it's not charging. The battery icon in the Windows taskbar to the bottom right says it's plugged in and charging, but the charge level never goes above 2%. I have checked and I don't have a hcarging switch on the laptop anywhere, so it should be charging. If I unplug the cable, the laptop runs out of power within 30 seconds or so, further fueling my thought that it's a faulty battery. Anyone have any bright ideas? If this doesn't get fixed I'll just ring up Sony and get them to send me a replacement battery or something. Thanks.

  Read the article

• Fixing mac user file permissions, not the system

  - by Cawas

  Usually those files get wrong permission when coming from the network, even when I copy them from it, but mostly through "file sharing". So, definitely not talking about Disk Utility repair here, please. But regardless of how the file got wrong permission, I know of two bad ways to fix them. One is CMD+I and the other is chown / chmod. The command line isn't all bad but isn't practical either. Some times it's just 1 file I need to repair, sometimes it's a bunch of them. By "repair" I mean 644 for files, 755 for folders, and current user:group for all of them. Isn't there any app / script / automator out there to do that?

  Read the article

• Computer not acknowledging sound card after move

  - by Angela

  We just got our computer back from having moved and when I tried to hook our speaker system, the computer keeps telling me that I don't have a sound system installed. It's a Dell computer with the original surround/subwoofer system that it came with and was working fine before the move. I tried buying a new speaker system (Logitech) to see if it would work, but still saying I have no audio device installed and it's not showing up in my device manager. I opened up the computer and unplugged the sound card, then plugged it back in, still nothing. I put the install disc from the sound card in the cd-rom, but it's saying that I have no sound device hardware in my system.

  Read the article

• Dialog width does not work in FireFox

  - by coffeeaddict

  I do not understand why the dialog will not work for width in Firefox (latest version) but will in IE (latest version): dialogDiv.dialog ( { resizable: resizable, width: width, height: height, bgiframe: true, modal: true, autoOpen: false, show: 'blind' } ) No, it's not in a table..it's all tableless and I see it working fine in IE for width.

  Read the article

• rsync to EC2: Identity file not accessible

  - by Richard

  I'm trying to rsync a file over to my EC2 instance: rsync -Paz --rsh "ssh -i ~/.ssh/myfile.pem" --rsync-path "sudo rsync" file.pdf [email protected]:/home/ubuntu/ This gives the following error message: Warning: Identity file ~/.ssh/myfile.pem not accessible: No such file or directory. [email protected]'s password: The pem file is definitely located at the path ~/.ssh/myfile.pem, though: vi ~/.ssh/myfile.pem shows me the file. If I remove the remote path from the very end of the rsync command: rsync -Paz --rsh "ssh -i ~/.ssh/myfile.pem" --rsync-path "sudo rsync" file.pdf [email protected] Then the command appears to work... building file list ... 1 file to consider file.pdf 41985 100% 8.79MB/s 0:00:00 (xfer#1, to-check=0/1) sent 41795 bytes received 42 bytes 83674.00 bytes/sec total size is 41985 speedup is 1.00 ...but when I go to the remote server, nothing has actually been transferred. What am I doing wrong?

  Read the article

• Subversion error: (405 Method Not Allowed) in response to MKCOL

  - by Sergio del Amo

  I am getting the next error while trying to commit a new directory addition. svn: Commit failed (details follow): svn: Server sent unexpected return value (405 Method Not Allowed) in response to MKCOL request for '.... I have never seen this error before. Can someone help me? Solution I managed to solve the problem: Delete the parent's directory of the folder giving the problem. Did SVN Update A folder with the same name as the new one already existed in repository. Delete this folder SVN Commit Copy the new folder, Schedule for addition and SVN Commit

  Read the article

• Persistent network share connection not working with runas

  - by binarycoder

  If I use runas /user:DOMAIN\user cmd.exe (using XP), previously mapped persistent network drives are considered unavailable. net use shows: Status Local Remote Network ------------------------------------------------------------------------------- Unavailable H: \\SERVER\SHARE Microsoft Windows Network dir H: fails with "The system cannot find the path specified.". The connection is easily revived with `NET USE H: \SERVER\SHARE': not asked for a password when I do this. What is going on? Can I make Windows safely revive this drive automatically when it is first accessed.

  Read the article

• $RYSNC_PASSWORD not being read/responded-to correctly (Snow Leopard)

  - by warren

  Ignoring the security issues, I have the following script that synchronizes my music library from my MacBook Pro (running Snow Leopard) to the file store (CentOS 4) on my network: rsync -rav --progress --partial -e "ssh" ~/Music/iTunes/* user@scramasax:~/music/iTunes-scissor:~ When I try to use either a password provided on the command-line (), in a password file (--password-file), or in the environment variable RSYNC_PASSWORD, the login still goes interactive, requiring me to type my password again. I will be moving to pre-shared keys on my network, but in situations where that is not possible, such as rsync'ing files to a webserver, being able to successfully embed the password in the script would be very helpful.

  Read the article

• Is my disk hot or not?

  - by adriangrigore

  I am trying to figure out the temperature of my dedicated server's harddisk. For this purpose, I've downloaded HDTune to monitor the S.M.A.R.T. Status. The problem is that the current temperature for "C2 Temperature" is 73 degrees celsius, but the little thermometer on top of the window shows 27 degrees celsius. See this screenshot: http://screencast.com/t/OGJhZGIxND Another monitoring software (Anfibia Reactor) shows similar behavior: Disk temperature is around 30 degrees, but it says that the disk is too hot. So, is my disk hot or not? Since this is a dedicated server, I can't just open the case and put a thumb on it.

  Read the article

• LAN not picking up gigabit connection through patch panel

  - by user332555

  I have just purchased 2 FVS318G switches to install at my store. How this is set up is the server is in the back room. We have Cat 5E ran up through the ceiling and is patched into a panel in the back room. The 2 switches I just purchased are right next to the server in the back where all the cables patch in. I do a direct connection from the server to switch, avoiding the patch panel completely, and receive 1.0 gbps connection no problem. When i patch in the register computers from the front into the panel and then to the switch I am only getting 100 mbps on the registers up front. The patch panel does say Cat 5E on it but I am not sure if there is any interference in the line somewhere and I cannot get the full 1.0 gbps to the front registers like I want. Any ideas??

  Read the article

• MYSQL query to return rows that are NOT in a set

  - by iglurat

  Hi, I have two tables: Contact (id,name) Link (id, contact_id, source_id) I have the following query which works that returns the contacts with the source_id of 8 in the Link table. SELECT name FROM `Contact` LEFT JOIN Link ON Link.contact_id = Contact.id WHERE Link.source_id=8; However I am a little stumped on how to return a list of all the contacts which are NOT associated with source_id of 8. A simple != will not work as contacts without any links are not returned. Thanks.

  Read the article

• Problem using ScriptManager.RegisterStartUpScript in user control - Script Error "function is not de

  - by poojad

  I have a aspx page which contains a User Control uc1 ans within uc1, there is another user control uc2. Now I need to call a javascript function in the uc2's page load. (I understand that the Pages are not properly designed, but I am sorry as this is an old application, I am not supposed to make any changes in the design) I am doing this using ScriptManager.RegisterStartUpScript as I have an update panel, but the function is not being called and the script error "load is not defined" is fired. (load is the javascript function in uc2) Can anyone help me out with this? Thank you.

  Read the article

• Rails Installed But Not Working

  - by Luiz P

  Folks, Yesterday I installed Rails 3.2 on Ubuntu 12.10 and created a new project in order to check it. It was working OK. Today I tried to create a new project and got the message bellow (Portuguese version): O programa 'rails' pode ser encontrado nos seguintes pacotes: * rails * ruby-railties-3.2 Tente: sudo apt-get install <pacote selecionado> Something like: The program 'rails' could not be found in the follow packages: ... ... Try: sudo apt-get install <selected package> I run the command gem list and all the gems are listed, including Rails one. I tried to search on the web for a solution, but haven't found any. Thank you very much for your help. Luiz

  Read the article

• Play framework does not return page and static content

  - by Anton

  I'm using play framework in production for one of my web projects. From time to time Play does not render main page or does not return some of the static content files. I have attached few screenshots below. First screenshot displays firebug console, loading of the site is stucked at the beginning, when serving home page. Second screenshot display fiddler console, when 2 static resources are not loading. This issue is hard to reproduce, it happens 1 of 15 time, I have to delete cache data and reload page. (pressing CRTL-F5 in FF). Issue can be reproduced in most of the browsers. Initially, I was thinging that there is something wrong with hosting provider. But I have changed hosting provided and issue has not gone. Version of the play is 1.2.2. Play is running as standalone server. Not sure, but probably deploying Play to Jetty/Tomcat/Resin would help. Also I'm thinging about rewriting application to another stack (well-known for me - j2ee, spring, whatever) I have no idea how to debug and resolve this issue. Any clue ? Has anyone faced same issue with Play before ?

  Read the article

• Original sender is not correctly identified when spam is forwarded

  - by Stephan Burlot

  I have a forwarding rule with Postfix that forwards all messages to my main email address. When a spam message is sent to one of my emails, it is forwarded but the sender is shown as being the forwarding domain, not the spammer's domain. Real example: mywebsite.com is hosted on Linode. [email protected] sends an email to [email protected] the mail is forwarded to [email protected] my email hosting (anotherwebsite.com) sees it's spam and sends a message to [email protected] and Linode reports a TOS violation. I have modified my postfix settings so I now use RBL, but if a message goes through, it may happen again. How can I prevent this to happen again? Is there some settings to change on Postfix so the original sender is correctly identified? Thanks Stephan

  Read the article

• Mac OS X: at command not working

  - by David.Chu.ca

  I am going to schedule a job by using at command. Here I tried the following command: $ at now + 1 minute echo 'Test at command' <EOD> I saw the job is scheduled by using at -l. However, I saw no echo out. I guess that I may need to add user to at.allow file. I cannot find at.allow in my Mac (Snow Leopard). Not sure what I need to do to test this at command?

  Read the article

• Digital audio does not work on MacBook Pro

  - by mathk

  I have a MacBook Pro (8,2). Using a TOSLINK cable I have no digital output. Oddly enough, sometime I can hear a glitch when I plug in the cable or when I give it a gentle wiggle. My guess is that the output is not correctly detecting that I have a digital link. So is there a way to force digital audio output on a MacBook Pro? Some say that in the Audio MIDI Setup there is an option but I can't find it. I am running OS X 10.7.5.

  Read the article

• eclipse adding java ant based project: Specified buildfile does not contain a javac task

  - by ufk

  Hello. I have a project that i wrote for apache tomcat. I started working with eclipse i want to import the project to eclipse ide. using eclipse 3.6.1. when i create a new project using : File - New - Other - Java - Java Project from Existing Ant Buildfile and i provide the build file location i get the following error: Specified buildfile does not contain a javac task I have a red5 project that i used the same method and it worked. what am i missing? do i need to add something to the ant build file to make it work? what exactly ? where can i find more information regarding this specific subject ? thanks!

  Read the article

• Can not set Windows XP Keyboard configuration

  - by Bluebird75

  A friend of mine came to me with a french Windows XP where windows had decided that keyboard would now be english-US keyboard instead of french keyboard. After a few attempts, I came to the strange conclusion that it's impossible to change it. Whatever keyboard configuration I apply, the language dialog does not complain but sticks to the english-us keyboard. I tried : setting two keyboards, with FR as default setting two keyboards, with EN-US as default one keyboard as FR It's like it was impossible to apply a new keyboard configuration. Any idea what could be wrong ?

  Read the article

• Extending C drive not possible

  - by gokul

  This is my computer partition list. You can see my C drive is running very low on disk space. I wanted to extend my disk space, so I used mmc Disk managment to shrink a volume, but I can't extend it to the C drive because the extended volume in dropdown list of C is not clickable. I've tried many packages, but none were able to do it. My C drive is simple, basic, NTFS, healthy (boot, crash dump, primary partition). The MMC Windows: What should I do?

  Read the article

• mod_rewrite not working?

  - by Sean Kimball

  I have a bunch of non-existent urls that need to be redirected to new ones, though they are not working... mod_rewrite does work and is enabled, I'm wondering if the redirect URL has to actually exist in order for a redirect ot work. Here is what I have: Redirect 301 /cgi-bin/commerce.cgi?display=action&emptyoverride=yes&template=Assets/XHTML/Advantage.html http://domain.com/the-bag-to-nature-advantage.html UPDATE this is the request that comes in [indexed in google!] http://domain.com//cgi-bin/commerce.cgi?display=action&emptyoverride=yes&template=Assets/XHTML/Advantage.html this is where it needs to go: http://domain.com/the-bag-to-nature-advantage.html

  Read the article

• Outlook rules not working together

  - by JBurace

  I have multiple Outlook (2010) rules and these 2 are having issues together: Rule 1: Apply this rule after the message arrives with blahname in the sender's address and move it to the BlahBox folder. Rule 2: Apply this rule after the message arrives from [email protected] move it to the NoReply folder. If I have rule 1 above rule 2, only rule 1 works (noreply emails stay in the Inbox folder). If I swap and have rule 2 above rule 1, only rule 2 works (blahname emails stay in the Inbox folder). What am I doing wrong; how can I fix this so it applies both rules on incoming email? I'm fairly certain the two rules should never intersect (blahname != domain.com). Also I do not have "this computer only" checked on any rules, I avoid client-only rules.

  Read the article

< Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >