Search Results

Search found 30308 results on 1213 pages for 'dont ask'.

Page 257/1213 | < Previous Page | 253 254 255 256 257 258 259 260 261 262 263 264  | Next Page >

• Mouse scroll issue after kernel build

  - by Anish S Kumar

  I have a Intel Cedar Trail netbook. For graphics to work, i had to build kernel 3.1 with the drivers. I followed the steps in this document After doing that, now my graphics is fine, but my mouse scroll does not work. Is that because I have not build the kernel properly? Have i missed selecting some options in the kernel compile menu? It will be nice if someone can help me. Also my wacom bamboo tablet is not recognized, i have installed the xserver-xorg-input-wacom drivers.

  Read the article

• Automatic TRIM vs. manual TRIM

  - by Eike Cochu

  I am currently trying to find out how to trim with my new TP and was wondering about the difference of manual/online trimming. Here is my setup: ThinkPad T430s with SSD Samsung 830, 128GB and Xubuntu 12.10, here are some outputs to check if trim will work on my system (got these from here: http://wiki.ubuntuusers.de/SSD/TRIM) root@eike-tp:~# sudo hdparm -I /dev/sda | grep -i TRIM * Data Set Management TRIM supported (limit 8 blocks) First, I tried the online trimming: How to enable TRIM? my fstab with discard inserted: UUID=d6c49c17-a4f1-466c-9f7e-896c20db3bba / ext4 discard,noatime,errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=a0322f5f-c6c1-4896-863f-668f0638d8cf none swap sw 0 0 tmpfs /tmp tmpfs defaults,noatime,mode=1777 0 0 I tried to test if it works (but I don't get any zeroes when I try it with /dev/sda), but found out that this method is only possible with SSD type 2 and I seem to have type 3. So I don't know if it works or not. The Ubuntuwiki (first link) recommends manual trimming, so I set up a daily cronjob instead of discard: #!/bin/sh LOG=/var/log/batched_discard.log echo "*** $(date -R) ***" >> $LOG fstrim -v / >> $LOG the wiki article suggests weekly or daily. Now to my questions: How often executes the automated trim? How often is recommended? Online vs. manual trimming? Thank you for your help

  Read the article

• Update Error: Require Installation Of Untrusted Packages

  - by One Zero

  I have googled and found out Updates don't install because of "untrusted packages". It didn't fixed the error. So, how do I fix my GUI update? Updated sudo apt-get update && sudo apt-get upgrade < working The following packages will be upgraded: ambiance-colors radiance-colors 2 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 5,029 kB of archives. After this operation, 7,614 kB of additional disk space will be used. Do you want to continue [Y/n]? y WARNING: The following packages cannot be authenticated! ambiance-colors radiance-colors Install these packages without verification [y/N]? Working but when I update from GUI or try to install software from Ubuntu Software Center I got same error as shown in above picture. For every software I have to install it from command line because I got same error when install software from Ubuntu Software Center.

  Read the article

• Squid 3 and Internet Explorer 11 with authentication

  - by StBlade

  Need some help. My college has up until now been running Squid 3 on Ubuntu 12.02 and now 14.04 successfully. That was till recently. Our WSUS server is dishing out updates to all our workstations of which Internet Explorer 11 is one of them. Now all of a sudden users do not need to authenticate via the squid proxy to be able to use the internet. This makes it rather difficult as I also use SARG to generate usage logs for all users each day. All our workstations also have Chrome on them, and Chrome authenticates fine via the Squid proxy. Doing a couple of Googles, I ran into and article, where someone made mention that Microsoft has deprecated digest and basic authentication from IE 11. Reason was given that Office 2013 was giving problems as it was not giving the popup screen for authentication when Office tries to download templates from the internet. I have run into this problem, but by setting those sites to not authenticate via squid fixed the problem. Has anyone else run into something similiar? Would changing to NTLM or Kereberos be a solution?

  Read the article

• Running an old version of some software

  - by Mark Oak

  I don't want to mingle in any backstory, but all that needs to be known is that I have a computer with Ubuntu on it and I am trying to install Windows 8 from an ISO. I am using the guide that can be found here which is a little more than four years old. Now, I've been able to accomplish everything up to Step 2, at which point I am stuck. I have downloaded the file found on that page, which can be found here, and have attempted to use it, as directed, quote; "right click the downloaded Unetbootin file, select Properties and on the "Permissions" tab, check the "Allow executing file as program" box. Then simply double click it and it should open." But, after having set checked the specified box and double clicking the file, nothing happens. Nothing is launched and nothing changes. I've been stuck here for several hours now, having failed to find a solution via Google.

  Read the article

• disk space worngly displayed after installing LVM disk

  - by Ubuntuser

  I installed ubuntu server using LVM partitioning on a 1 TB hard disk. However, after installation, i can only see 10 Gig space here is the fidsk output ` # fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00041507 Device Boot Start End Blocks Id System /dev/sda1 * 1 10 71680 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 10 121602 976689152 8e Linux LVM Disk /dev/dm-0: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 2147 MB, 2147483648 bytes 255 heads, 63 sectors/track, 261 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table You have new mail in /var/mail/root and df -h output df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/system-root 9.9G 6.6G 2.8G 71% / devtmpfs 1.9G 232K 1.9G 1% /dev tmpfs 1.9G 4.0K 1.9G 1% /dev/shm /dev/sda1 68M 22M 43M 34% /boot tmpfs 6.0G 0 6.0G 0% /var/spool/asterisk/monitor You have new mail in /var/mail/root ` any way to increase this space without reisntalling?

  Read the article

• Unable to boot Windows after installing Ubuntu 12.04 - error: invalid efi file path

  - by user113350

  I have a Laptop (ASUS X310A, I installed Ubuntu 12.04 to be side by side with Windows 7 but I seem to have gotten a problem with booting Windows 7. I used the Boot Repair twice with no results. Boot-Repair info: http://paste.ubuntu.com/1417623/ The error I get when starting Windows 7 from GRUB is: error: invalid efi file path In Boot Manager or Menu, I have 3 options now: 2x for Ubuntu (maybe cause I did boot-repair twice) 1x Windows boot manager (If I boot this it opens "ASUS Preload Wizard", it gives me the option to re-install windows losing all previous data -) When I was making the partition before installing Ubuntu, I made the new partition by making sda4 smaller and adding ext4 mounted: "\" and adding a swap area. Installed it and it didn't work, nothing worked. So i booted Ubuntu from the USB again and deleted the partitions I made and decided to make sda3 smaller and making the partitions but this time it gave me the option that I could mount sda3 on "\windows" or "\dos" I ignored it and didn't choose neither because the I know that it doesn't need to be mounted and proceeded to create what is now sda7 (ext4) and sda8 (swap area). It still didn't work so I booted from USB and did the first boot-repair, so I was able to boot Ubuntu now but not windows, but when I did it through my USB I was not able to update boot-repair, so i decided to redo the boot-repair from Ubuntu running on the Hardisk (fully updated) and it still didn't work. In GRUB this is what i see (when booting using Ubuntu as first option in Boot Menu): Ubuntu, with Linux 3.2.0-29-generic Ubuntu, with Linux 3.2.0-29-generic (recovery mode) Windows UEFI loader Windows Boot UEFI bootx64.efi.bkp Windows 7 (loader) (on /dev/sda3) Windows Recovery Environment (loader) (on /dev/sda5) I tried all the ones starting with "Windows" they all don't work Please help, Many Thanks

  Read the article

• Expiry time in notify-send notifications

  - by gsingh2011

  On my HP computer running Ubuntu 12.04, the brightness and volume increments were much higher than I wanted. On top of that, the notification for the volume was just plain wrong (0% sound did not correspond to 0 on the progress bar). So I decided to override these options with my own commands. I used CompizConfig Settings Manager to add custom commands to the brightness and volume keys (this couldn't be done in the regular settings because these keys were handled by the BIOS, unlike normal function keys). I used xbacklight to control the brightness and amixer to control the volume. The problem is that the nice notify-send notifications don't show up when I manually set the brightness/volume, so now I have to do that myself too. However, there are two problems with notify-send: The expire time option doesn't work You have to wait until a notification is finished before the next one comes up Before I overrided the brightness/volume keys, the system was able to send notifications without these two restrictions. Notifications disappeared within 3 seconds (instead of the default 10), and if I double tapped the volume or brightness button, the progress bar would immediately change to the new brightness (instead of showing the old progress bar for 10 seconds and then showing the new one). Since the system was able to do it, I was wondering how I can achieve the same type of notifications?

  Read the article

• How to have many Ubuntu workstations centrally managed?

  - by Richard Zak

  I have about a dozen Alienware workstations that are used for CUDA development and for execution of MPI jobs. What is the best way to manage them? I'd like to have something like an apt-get but for several systems, and a way to reimage a system simply and centrally. It seems that a combination of Landscape and Canonical's MAAS would be a good fit, but I need an open source solution. Any thoughts?

  Read the article

• How can I set a second screen (DISPLAY=:0.1) as the default gnome display?

  - by Pedro Silva

  Due to various reasons, I have my main monitor set as the secondary display in xorg.conf. I would like to have gnome initialize metacity, gnome-panel as running primarily on :0.1, instead of :0.0. Is this possible at all? To clarify, this is a laptop with its LCD turned off. My main monitor is connected to the VGA out and is driven by the nouveau driver for NVIDIA; a secondary monitor is on a displaylink usb-vga donverter. The seconday monitor is set in xorg.conf as the primary display (no way around it). I can do things like DISPLAY=:0.1 gnome-terminal to run applications on the main monitor. My question is whether it is possible to do this (GNOME-) system-wide.

  Read the article

• How do you globally set the default browser using KDE4?

  - by wishi

  Hi! I'm using awesome-wm on Kubuntu 10.10. I like some of the KDE tools... like choqok. Thing is, that within awesome wm it seems to be impossible to set a default browser, because KDE4 settings overwrite the generally desired settings: To illustrate the problem: % xdg-mime query default text/html chromium-browser.desktop And from ~/.kde/share/config/kdeglobals [General] BrowserApplication=firefox.desktop Which does in no way make sense to me. If I set Firefox as default xdg-mime should not have Chrome. In fact I want Firefox. So how do I globally once and for all, across all frameworks, define Firefox as default? Best, Marius p.s.: I should probably mention, that clicking in Choqok starts Konqueror...

  Read the article

• Windows move to external monitor when closing lid

  - by Martijn

  I'm using Cinnamon (on 12.10) on a laptop (Compaq 6710b business model) with an external monitor. Both screens run at 1680 x 1050, the external monitor is located on the right. During normal operation everything works fine; windows open in whatever monitor my mouse pointer is when they open and I can freely drag them to the other monitor. When I close the lid of my laptop both displays shut down as expected. When I open the lid, however, the lock window opens on the external monitor and any windows that were open on the laptop screen have moved to the external monitor as well. Nothing happens between closing the lid and opening it; no suspend, powerdown, hibernate or anything, monitor stays attached; even mouse is untouched (pointer on laptop screen). Is there any way to fix it so my windows stay on whatever monitor I left them before closing the lid? Alternative solutions are welcome.

  Read the article

• Network Issues only on one network with a Broadcom BCM4312

  - by Ryan McClure

  My Ubuntu 11.10 laptop is having network connection issues...only on one network. I have a BCM4312 card and I'm using the proprietary driver. Whenever I connect to a network over wireless connection, I have no trouble except for one network. In my dorm, if I try to connect to the wireless network, it stays connected from anywhere to 30 seconds to 30 minutes before it will still be "connected" according to the indicator but there is no incoming/outgoing internet connection. This only happens in this building. Other networks with the same name at other buildings on my campus have no issue whatsoever. I took it to the tech department here and they keep claiming it's my laptop; but, if I can connect to other networks with absolutely no issues, why can't my laptop connect here? So, here's my question: Is it my laptop, or is it the network? As a side note, no one else that I know has issues on this network but one; she's running Windows 7 and I forget what kind of laptop it is. One of the people in my hall runs Ubuntu 12.04 and has no problem with the wireless. What do you all think of this?

  Read the article

• How to force a new Notification in notify-osd to show up without waiting for the earlier one to exit?

  - by Nirmik

  I have made a script(and a .desktop shortcut leading to this script) for starting and stoping xampp... It checks the status of xampp and accordingly either starts or stops xampp. Now i have assigned a notification as soon as the script is started to display "Starting xampp..." or "Stopping xampp..." and then when xampp is started or stopped,it displays "Xampp started..." or "Xampp stopped..." I've used notify-send to show notification as seen in the script below Now the thing is that here,the second notification waits for the 1st one to disappear and then pops up even if xampp has started/stopped. I want the new notification to appear immediately by forcing the earlier one to exit before the completion of its life-cycle. This can be seen to take plce when you activate/deactivate wireless/networking immediately... For example the "Wireless enabled" comes up on selecting enable wireless and if you immediately select disable wireless,the "Wireless disabled" notification comes up without waiting for "Wireless enabled" notification to complete its life-cycle. So how do i achieve this? #!/bin/sh SERVICE='proftpd' if ps ax | grep -v grep | grep $SERVICE /dev/null then notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "Stopping XAMPP..." && gksudo /opt/lampp/lampp stop && notify-send -i /opt/lampp/htdocs/xampp/img/logo- small.gif "XAMPP Stoped." else notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "Starting XAMPP..." && gksudo /opt/lampp/lampp start && notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "XAMPP Started." fi On the man page for notify-send I found --urgency=LEVEL or -u where levels are low, normal, critical. Is this of any use? making it critical? Also I tried it with the command- notify-send -u=critical"Testing" but that dint work...it gives the error- Unknown urgency criticalTesting specified. Known urgency levels: low, normal, critical. or if I give the command notify-send -u=LOW"Testing" it gives me error missing argument to -u Any relation??

  Read the article

• Why am I getting a "network is unreachable" error on Ubuntu Server?

  - by jason328

  I'm a completely new to Ubuntu server and am having a hard time connecting the server to the internet. I first ran ping -n 8.8.8.8 connect:Network is unreachable Then I ran ifconfig Link encap:Local Loopback inet addr:127.0.0.1 Mask 255.0.0.0 inet6 addr: ::1/28Scope:host UP LOOPBACK RUNNING MTU:16436 RX packets:192 errors:0 dropped:0 overruns:0 frame:0 TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15360 (15.2KB) TX bytes:15360 (15.3KB) Here is ouput for sudo lspci -n 00:00.0 0600: 8086:2580 (rev 04) 00:02.0 0300: 8086:2582 (rev 04) 00:1d.0 0c03: 8086:2658 (rev 03) 00:1d.1 0c03: 8086:2659 (rev 03) 00:1d.0 0c03: 8086:265a (rev 03) 00:1d.0 0c03: 8086:265b (rev 03) 00:1d.0 0c03: 8086:265c (rev 03) 00:1e.0 0604: 8086:244e (rev d3) 00:1e.0 0401: 8086:266e (rev 03) 00:1f.0 0601: 8086:2640 (rev 03) 00:1f.0 0101: 8086:2651 (rev 03) 00:1f.0 0c05: 8086:266a (rev 03) 00:0b.0 0200: 8086:1654 (rev 03) lshw-c network returns WARNING: you should run this program as super-user. *-network DISABLED description:Ethernet interface product: NetXtreme BCM5705_2 Gigabit Ethernet vender: Broadcom Corporation physical id:b bus info:pci@0000:0a:0b.0 logical name: eth0 capabilities: bus_master_cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 firmware=5705-v3.18 latency=32 mingnt=64 multicast=yes port=twister pair lsmod code returned this Module Size Used By e100 37213 0 dm_crypt 23125 1 ppdev 17113 0 psmouse 87603 0 snd_intel8x0 38570 0 snd_ac97_codec 134826 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97188 2 snd_intel8x0, snd_ac97_codec serio_raw 13211 0 snd_timer 29990 1 snd_pcm snd 78855 4 snd_intel8x0, snd_ac97_codec, snd_pcm,snd_timer soundcore 15091 1 snd snd_page_alloc 18529 2 snd_intel8x0, snd_pcm ext2 73795 1 parport_pc 32866 1 mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev, parport_pc,lp usbhid 47199 0 hid 99559 1 usbhid tg3 152032 0 i915 468651 1 floppy 70365 0 drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 Again there is more but it's giving info on the driver itself. I know it works, I've used it. I assume then that my network got disabled when I installed Ubuntu Server. How do I enable it? I checked and the internet cable is connected to the D-link router. I have also used this same computer for internet access when I had Ubuntu Desktop installed so internet does work.

  Read the article

• probability of trouble-free upgrade

  - by intuited

  One of the problems with recommending Ubuntu to potential future users, especially those not particularly given to technical endeavours, is that there is a chance that upgrades will break their machine, and they'll have to pay or otherwise coerce some knowledgeable person into fixing them. In my limited experience of running successive versions of Ubuntu since 8-something on a couple of different laptops, this chance is quite high. I'm not sure if I'm just unlucky with the hardware that I'm using, or if it's a result of the higher-than-average number of packages I have installed, or if upgrades are just typically problematic. So I'd like to know the likelihood, for a casual user, of doing a release upgrade, for example from 10.04 to 10.10, without experiencing any regression bugs. Obviously this is dependent on the hardware that people are running. Canonical seems to be making some efforts towards collecting data on this, for example with the "I am affected by this bug" checkbox on their issue tracker, and with the laptop compatibility reports, but I've not seen anything comprehensive. I'm hoping for an objective reference here, for example a study carried out by relatively unbiased individuals. However, anecdotal evidence is probably useful too.

  Read the article

• Release upgrade crashes with "W:Failed to fetch http://host/debian/dists/oneiric/Release.gpg"

  - by Nolan Dillard

  My update manager told me that it has not checked for updates in the past 18 days, so I clicked the "check" button. It works just fine until a certain point where it says "Downloading release". The loading bar moves across the screen for a while on that message, then it just stops and says to check my Internet connection. I am fairly certain that my Internet is fine, as I can do anything else that I have tried, including installing software over the Internet. I clicked on "Details" and this is what turned up: Log

  Read the article

• How to restore curropted installation?

  - by nightweels

  I have a laptop with dead battery that when there is no current connected to it turns critical so fast and in the energy management in ubuntu, when the battery is critical, there are 2 options: shutdown and hibernate witch is in grey (unclickable), so I have no choice but to chose immediate shutdown, there is no standby even if it is an option in the screen behavior. An immediate shutdown (and I mean by immediate the one that we use when we ended using the computer) happened while I was installing a program called quickly, so after the power was restored, I tried to reinstall the program then I get this translated message: An untreatable error occurred: It seems there is a software error in aptdaemon, the program that lets you install and remove software and any other task related to package management. details: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/aptdaemon/worker.py", line 968, in simulate trans.unauthenticated = self._simulate_helper(trans) File "/usr/lib/python2.7/dist-packages/aptdaemon/worker.py", line 1092, in _simulate_helper return depends, self._cache.required_download, \ File "/usr/lib/python2.7/dist-packages/apt/cache.py", line 235, in required_download pm.get_archives(fetcher, self._list, self._records) SystemError: E:I wasn't able to locate a file for the libpng12-dev package. This might mean you need to manually fix this package.

  Read the article

• I'm not sure if this is a valid Ubuntu bug to file

  - by Ian Hincks

  I was in the process of filing an bug on Launchpad, but I had second thoughts because there were so many threatening warnings of the effect, "Don't file a bug report unless you're sure it's a bug, and you should really provide a package name". The problem I have, and I've had it for years, is the following: When I'm installing Ubuntu, it asks me to type in my location before it asks me what my keyboard layout is. Using a QWERTY keyboard but with the buttons popped of and in the Dvorak order, this is annoying, because it is assumes I am using a QWERTY keyboard, and so I have to guess at where all the QWERTY keys are to spell my city's name. It seems like it would make more sense to switch the order of these two questions. (I'll be the first person to admit that this is a very minor problem that has probably wasted less than 2 minutes of my life in total -- but it's the principle of the thing :p) So my question is: is this order there for a particular reason, and if it isn't, is it appropriate to file it as a bug, and under which package name?

  Read the article

• How can I switch between fglrx and ati drivers?

  - by Santa Maradona

  Hi there, How can I switch between fglrx and ati (open source) drivers without uninstalling fglrx? The thing is I'm using FGLRX on a daily basis, because it's better for movies--OS driver displays annoying horizontal line while playing movies. FGLRX also does this, but it's less visible. That's only disadvantage of OS driver. When I want to plug in external monitor with different resolution than my laptop's LCD I have to use open source driver, because FGLRX can't display two different resolutions at the same time. I can uninstall FGLRX, but it's rather inconvenient to do this all the time. I've noticed that when I'm using FGLRX there is xorg.conf file and when I uninstall it, then the file is missing. So my question is how to switch between them? It'll be perfect if I could do this without restarting my computer either. I'm using Ubuntu 10.10, laptop/netbook MSI U250.

  Read the article

• GPU hung when switching graphic card

  - by Lie Ryan

  I have a laptop (Dell Inspiron N4110) with a switchable graphic. $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: ATI Technologies Inc NI Whistler [AMD Radeon HD 6600M Series] (rev ff) Normally, my laptop starts with both graphic cards enabled, which caused the laptop to turn very hot and the fan to become very noisy. I have been using a small script to disable the Radeon card. For some time, I'm quite happy with this arrangement. However, I have been having some issues with the Intel card (IGD), the Intel card often randomly hang when running OpenGL apps; and so I want to give the Radeon card (DIS) another chance. I have never been able to switch to the Radeon card, but recently, I found out that if I do a "delayed switching" (DDIS): # echo "DDIS" > /sys/kernel/debug/vgaswitcheroo/switch root@lieryan-dell-ubuntu:/sys/kernel/debug/vgaswitcheroo# cat switch 0:IGD:+:Pwr:0000:00:02.0 1:DIS: :Pwr:0000:01:00.0 then I logoff (i.e. to restart X), the screen switch to pseudo-tty and then it stuck there freezing. At this situation, mouse and keyboard stops working so I can't switch to another ptty. I tried ssh-ing from another computer to salvage logs (dmesg at that point) and whatnot; I found out that when freezing, the active graphic card is the AMD card: -- this is from ssh -- # cat switch 0:IGD: :Off:0000:00:02.0 1:DIS:+:Pwr:0000:01:00.0 but the GPU is apparently hung, looking at dmesg gives: ... [ 1411.649974] vga_switcheroo: client 0 refused switch [ 1411.649985] vga_switcheroo: setting delayed switch to client 1 [ 1423.911759] vga_switcheroo: processing delayed switch to 1 [ 1424.006564] fbcon: Remapping primary device, fb1, to tty 1-63 [ 1424.006799] i915: switched off [ 1424.840351] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1425.718088] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1426.622377] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1427.355683] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1428.193549] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id ... the invalid framebuffer id error is repeated for many times over ... I were able to successfully recover by switching back to the Intel card and restarting X from ssh; indicating that only the Radeon card has problems switching. System info: $ uname -a Linux lieryan-dell-ubuntu 3.0.0-14-generic #23-Ubuntu SMP Mon Nov 21 20:28:43 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric The laptop also do not have the option to set graphic card at BIOS and the proprietary driver, fglrx, also have never worked; when I installed it through jockey ("Additional Drivers"), glxinfo showed that it still being rendered by Mesa, the /sys/kernel/debug/vgaswitcheroo directory has gone missing, and the driver crashes with a traceback if I use xorg.conf to tell X to use fglrx. Anyone had any idea if it is possible to use this AMD card either with the radeon or the fglrx driver? logs: dmesg

  Read the article

• Sound stopped working

  - by Brian West

  I ran through the troubleshooting at https://help.ubuntu.com/community/SoundTroubleshooting It did not play the test sound, and it also does not play sounds during speaker-test. It does play sounds when I adjust my volume on my computer (using pommed). It worked just the other day, but this is the first time I've tested it since last night, when I put it to pm-suspend-hybrid and it half-woke up (the backlight came on, but it didn't fully wake up), then went back, then half-woke again, but was frozen like that. I had to do a manual reboot of the machine when that happened. Now my sound doesn't work, except for adjusting the volume (where the little "beep" sound plays). During the troubleshooting, it recognized my sound card, the sound modules, and the sound card's installation. I've tried removing ~/.pulse, but to no avail. Also, if it's any help, pulseaudio is running, but pulseaudio --check returns nothing, which the manpage suggests indicates an error. Edit: I should probably clarify that the wake up from the suspend-hybrid was not provoked in any way. I was laying in bed when I noticed my room was brighter suddenly, so I got up to check on it.

  Read the article

• How to disable "N" Wireless Mode RTL8192 (Thinkpad Edge 15 Core i5) in natty

  - by Gustavo Rubio

  I've seen many owners of thinkpad edges which are supossed to be linux-friendly having problems with wireless adapter. I've found several links inside askubuntu and in ubuntuforums which have a lot of work-arounds for those problems, mine seems to be wierd though. I use my laptop on both my office and at home. At home I have a router which is A/B/G and here at home the wireless connection works just fine, using a WEP key. But in work I have a B/G/N wireless router and it doesn't work, my guess is that this adapter works with N modes but somehow this is buggy in the bundled driver in natty. I've tried to disable the "N" mode in the router but that didn't work. Later I went to realtek website, downloaded their driver and compiled myself, kinda seems to work most of the time but sometimes some websites keep trying to load or load just parts of it and images start to look like their links are broken and so on, much like what you get when you were loading a page and suddenly the connection is lost. This problem, as I said, is only using the realtek driver from their website. Dmesg gives me this a lot of these: [ 5869.049454] rtl8192se_update_ratr_table: ratr_index=0 ratr_table=0x00000ff5 [ 5879.240563] DHCP pkt src port:68, dest port:67!! So I thougth I might as well switch back to the original driver which seems to work just fine on A/B/G wireless networks but not on N networks so if anybody knows how to disable that mode from within the driver please let us know :) Thanks in advance! PS: I do found a link to a similar question and it was answered but let me remind you I'm NOT using the intel version of wireless for my thinkpad but the realtek (RTL8192SvB)

  Read the article

• How to use RDP protocol in Remote Desktop Viewer?

  - by drgrog

  I am using a Natty Live-USB, and the Remote Desktop Viewer application (Applications - Internet - Remote Desktop Viewer) only shows SSH & VNC protocols. How can I include RDP in the list, in order to connect to existing Windows Remote Desktop sessions on Windows XP machines. I am aware that I can use the gnome-rdp application, or even rdesktop hostname from a terminal, but I would like to create a persistent LiveUSB that uses Remote Desktop Viewer to connect to Windows RDP (port 3389). I do not want to set up VNC, TeamViewer or any others, as these do not solve my problem due to the fact they need additional software on the remote hosts.

  Read the article

• juju -v status ERROR Invalid SSH key

  - by Captain T

  root@cloudcontrol:/storage# juju -v status 2012-06-07 11:19:47,602 DEBUG Initializing juju status runtime 2012-06-07 11:19:47,621 INFO Connecting to environment... 2012-06-07 11:19:47,905 DEBUG Connecting to environment using node-386077143930... 2012-06-07 11:19:47,906 DEBUG Spawning SSH process with remote_user="ubuntu" remote_host="node-386077143930" remote_port="2181" local_port="57004". The authenticity of host 'node-386077143930 (10.5.5.113)' can't be established. ECDSA key fingerprint is 31:94:89:62:69:83:24:23:5f:02:70:53:93:54:b1:c5. Are you sure you want to continue connecting (yes/no)? yes 2012-06-07 11:19:52,102 ERROR Invalid SSH key 2012-06-07 11:19:52,426:18541(0x7feb13b58700):ZOO_INFO@log_env@658: Client environment:zookeeper.version=zookeeper C client 3.3.5 2012-06-07 11:19:52,426:18541(0x7feb13b58700):ZOO_INFO@log_env@662: Client environment:host.name=cloudcontrol 2012-06-07 11:19:52,426:18541(0x7feb13b58700):ZOO_INFO@log_env@669: Client environment:os.name=Linux 2012-06-07 11:19:52,426:18541(0x7feb13b58700):ZOO_INFO@log_env@670: Client environment:os.arch=3.2.0-23-generic 2012-06-07 11:19:52,426:18541(0x7feb13b58700):ZOO_INFO@log_env@671: Client environment:os.version=#36-Ubuntu SMP Tue Apr 10 20:39:51 UTC 2012 2012-06-07 11:19:52,428:18541(0x7feb13b58700):ZOO_INFO@log_env@679: Client environment:user.name=sysadmin 2012-06-07 11:19:52,428:18541(0x7feb13b58700):ZOO_INFO@log_env@687: Client environment:user.home=/root 2012-06-07 11:19:52,428:18541(0x7feb13b58700):ZOO_INFO@log_env@699: Client environment:user.dir=/storage 2012-06-07 11:19:52,428:18541(0x7feb13b58700):ZOO_INFO@zookeeper_init@727: Initiating client connection, host=localhost:57004 sessionTimeout=10000 watcher=0x7feb11afc6b0 sessionId=0 sessionPasswd= context=0x2dc7d20 flags=0 2012-06-07 11:19:52,429:18541(0x7feb0e856700):ZOO_ERROR@handle_socket_error_msg@1579: Socket [127.0.0.1:57004] zk retcode=-4, errno=111(Connection refused): server refused to accept the client 2012-06-07 11:19:55,765:18541(0x7feb0e856700):ZOO_ERROR@handle_socket_error_msg@1579: Socket [127.0.0.1:57004] zk retcode=-4, errno=111(Connection refused): server refused to accept the client This is from a clean install with 2 nodes all running 12.04 Precise juju bootstrap - finishes with no errors and allocates the machine to the user but still no joy after juju environment-destroy and rebuild with different users and different nodes. Anyone got any ideas

  Read the article

< Previous Page | 253 254 255 256 257 258 259 260 261 262 263 264  | Next Page >