Search Results

Search found 25057 results on 1003 pages for 'ie8 browser mode'.

Page 261/1003 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >

• iwconfig usage for WEP access point?

  - by johan elmander

  I would like to use my wifi doggle in my pc (ubuntu 12.04). I am able to connect to my access point through the GUI. I would like to do the same in the terminal. My access point uses WEP. So I typed the following commands iwconfig wlan0 mode managed key 6d6f6e6579 iwconfig wlan0 essid "AccessPoint" dhclient wlan0 after typing dhclient wlan0 it waits like 1-2 min then outputs nothing and cannot connect to the Access Point. iwconfig output: wlan0 IEEE 802.11bgn ESSID:"AccessPoint" Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long timit:7 RTS thr=2347 B Fragment thr:off Encryption key:6D6F-6E65-79 Power Management:off I would appreciate any suggestion

  Read the article

• Opera's Smart Solution

  Opera web browser now provides users to access restricted sites(by governments or abroad).

  Read the article

• Performance triage

  - by Dave

  Folks often ask me how to approach a suspected performance issue. My personal strategy is informed by the fact that I work on concurrency issues. (When you have a hammer everything looks like a nail, but I'll try to keep this general). A good starting point is to ask yourself if the observed performance matches your expectations. Expectations might be derived from known system performance limits, prototypes, and other software or environments that are comparable to your particular system-under-test. Some simple comparisons and microbenchmarks can be useful at this stage. It's also useful to write some very simple programs to validate some of the reported or expected system limits. Can that disk controller really tolerate and sustain 500 reads per second? To reduce the number of confounding factors it's better to try to answer that question with a very simple targeted program. And finally, nothing beats having familiarity with the technologies that underlying your particular layer. On the topic of confounding factors, as our technology stacks become deeper and less transparent, we often find our own technology working against us in some unexpected way to choke performance rather than simply running into some fundamental system limit. A good example is the warm-up time needed by just-in-time compilers in Java Virtual Machines. I won't delve too far into that particular hole except to say that it's rare to find good benchmarks and methodology for java code. Another example is power management on x86. Power management is great, but it can take a while for the CPUs to throttle up from low(er) frequencies to full throttle. And while I love "turbo" mode, it makes benchmarking applications with multiple threads a chore as you have to remember to turn it off and then back on otherwise short single-threaded runs may look abnormally fast compared to runs with higher thread counts. In general for performance characterization I disable turbo mode and fix the power governor at "performance" state. Another source of complexity is the scheduler, which I've discussed in prior blog entries. Lets say I have a running application and I want to better understand its behavior and performance. We'll presume it's warmed up, is under load, and is an execution mode representative of what we think the norm would be. It should be in steady-state, if a steady-state mode even exists. On Solaris the very first thing I'll do is take a set of "pstack" samples. Pstack briefly stops the process and walks each of the stacks, reporting symbolic information (if available) for each frame. For Java, pstack has been augmented to understand java frames, and even report inlining. A few pstack samples can provide powerful insight into what's actually going on inside the program. You'll be able to see calling patterns, which threads are blocked on what system calls or synchronization constructs, memory allocation, etc. If your code is CPU-bound then you'll get a good sense where the cycles are being spent. (I should caution that normal C/C++ inlining can diffuse an otherwise "hot" method into other methods. This is a rare instance where pstack sampling might not immediately point to the key problem). At this point you'll need to reconcile what you're seeing with pstack and your mental model of what you think the program should be doing. They're often rather different. And generally if there's a key performance issue, you'll spot it with a moderate number of samples. I'll also use OS-level observability tools to lock for the existence of bottlenecks where threads contend for locks; other situations where threads are blocked; and the distribution of threads over the system. On Solaris some good tools are mpstat and too a lesser degree, vmstat. Try running "mpstat -a 5" in one window while the application program runs concurrently. One key measure is the voluntary context switch rate "vctx" or "csw" which reflects threads descheduling themselves. It's also good to look at the user; system; and idle CPU percentages. This can give a broad but useful understanding if your threads are mostly parked or mostly running. For instance if your program makes heavy use of malloc/free, then it might be the case you're contending on the central malloc lock in the default allocator. In that case you'd see malloc calling lock in the stack traces, observe a high csw/vctx rate as threads block for the malloc lock, and your "usr" time would be less than expected. Solaris dtrace is a wonderful and invaluable performance tool as well, but in a sense you have to frame and articulate a meaningful and specific question to get a useful answer, so I tend not to use it for first-order screening of problems. It's also most effective for OS and software-level performance issues as opposed to HW-level issues. For that reason I recommend mpstat & pstack as my the 1st step in performance triage. If some other OS-level issue is evident then it's good to switch to dtrace to drill more deeply into the problem. Only after I've ruled out OS-level issues do I switch to using hardware performance counters to look for architectural impediments.

  Read the article

• Disable incognito in chrome or chromium

  - by TheIronKnuckle

  I'm addicted to certain websites to the point where it's interfering with my life regularly and sick of it. I want to install website blockers that aren't easy to circumvent. In Chrome, incognito mode is easily accessible with a ctrl-shift-n. That is ridiculous. Whenever I feel an urge to go on an addictive website, it doesn't matter what blockers and regulators I've got installed; three keys can get round them in a second. Simply uninstalling chrome isn't an option either, as it's way too easy to sudo apt-get install it right back. So yes, I want to disable incognito mode completely (and if possible making it totally impossible to get it back). I note that some guy has figured out how to do it on windows with a registry entry: http://wmwood.net/software/incognito-gone-get-rid-of-private-browsing/ If it can be done on windows it can be done on ubuntu!

  Read the article

• ati graphics always on

  - by naveen

  i use a lenovo y560 and has ubunto 12.04 and win 7 installed when i boot into ubunto i find that the ati car is always on which drains the battery and overheats the system is there any to switch off the ati graphics and use intel hd in ubuntu ati hd 5730 is the graphics card that i use and it has switchable graphics in it. in bios the only two options for video adapter is discrete and switchable after installing ati driver from amd website i am getting a commamd prompt as log in screen first error message comes as Your system is running in low-graphics mode with options to run in low graphics mode this time reconfigure exit all three options i am stuck i need to manually reboot the system

  Read the article

• How can i change focus when game locks it?

  - by GrizzLy

  I am playing wolfenstein:enemy territory, and if i play it in windowed mode, i can't change focus from game to something else (alt+tab doesnt work). EDIT1: As far as i could try, only ctrl+alt+Fx works (x is one number, for example F1 will switch to terminal). Could i somehow capture this kind of shortcut somewhere on X level and then send it to compiz to change focus (minimize currently focused window)? EDIT2: I found one other way, it works for Wolf:ET, it may help with other games too, if you turn on gameconsole (usually tilde key) game will release mouse lock (in windowed mode).

  Read the article

• How can I view localized versions of my site?

  - by Max Vernon

  We are adding internationalization to our site. We are getting the client's IP address from the headers and looking it up against the IP2location database to get the client's country. Several of our clients reported seeing a blank page over the weekend. We'd like to be able to get screenshots or use a browser from many different countries on an ongoing basis for testing code changes. I need to know what the site looks like when accessed from various countries since there are several elements that vary by country. I've used Tor and Vidalia, along with the Tor customized Firefox browser however it appears the CSS is getting mangled. I have also used http://webpagetest.org to check the site, however the screenshot it gives is too small to be really useful. Is there a site or a service I can use to get screenshots or interact with my website from various countries?

  Read the article

• Ubuntu 12.04 share the internet over WiFi from wvdial?

  - by Sour Lemon

  I have just installed Ubuntu 12.04 on a separate partition on my hard drive so I can dual boot to either Windows 7 or Ubuntu. I am living in Japan and so I'm using a mobile broadband USB device called "Softbank C02LC". By default it seems that this device isn't recognised so I did the following: Terminal: sudo su nano /usr/bin/usbModemScript Nano: #!/bin/bash echo 1c9e 9900 > /sys/bus/usb-serial/drivers/option1/new_id Terminal: chmod +x /usr/bin/usbModemScript nano /etc/udev/rules.d/option.rules Nano: ATTRS{idVendor}=="1c9e", ATTRS{idProduct}=="9900", RUN+="/usr/bin/usbModemScript" ATTRS{idVendor}=="1c9e", ATTRS{idProduct}=="9900", RUN+="/sbin/modprobe option" which made the device visible from the network manager etc. However even though I set up my details correctly when I created a new connection (Correct username, APN etc) as soon as I try to connect it almost immediately disconnects. Because of this I then followed the instructions at this site: http://debugitos.main.jp/index.php?Ubuntu%2F%A5%E2%A5%D0%A5%A4%A5%EB%A5%A4%A5%F3%A5%BF%A1%BC%A5%CD%A5%C3%A5%C8 And I ended up using the c02lc_connect script at the bottom of the page to connect to the internet. The file contains the following bash script: #!/bin/sh usbinterfece=/dev/ttyUSB2 VID=1c9e PID=9900 WRONG_PID=f000 LSUSB=/usr/sbin/lsusb GREP=/bin/grep MODPROBE=/sbin/modprobe SWITCH=/usr/sbin/usb_modeswitch SWITCH_D=/etc/usb_modeswitch.d WVDIAL=/usr/bin/wvdial SLEEP=/bin/sleep SUDO=/usr/bin/sudo WHICH=/usr/bin/which switch_config="$SWITCH_D/$VID:$WRONG_PID" if ! [ -x $WVDIAL -a -x $SWITCH ]; then echo "Install wvdial and usb_modeswitch." exit 0 fi check_usb() { local vid="$1" local pid="$2" ($LSUSB | $GREP "$vid:$pid") } if ! (check_usb "$VID" "$PID"); then echo "Cannot find modem device..." if (check_usb "$VID" "$WRONG_PID") && ( [ -f "$switch_config" ] ); then echo "The device is attached but its mode is wrong." echo "Try usb_modeswitch..." $SUDO $SWITCH -c "$switch_config" $SLEEP 1 if (check_usb "$VID" "$PID"); then echo "Successfully switched the mode." else echo "Failed to switch the mode..." exit 1 fi else exit 1 fi fi if [ ! -c "$usbinterface" ]; then $SUDO $MODPROBE usbserial vendor=0x$VID product=0x$PID $SLEEP 2 fi $SUDO $WVDIAL which works completely fine - no problems what-so-ever. But we also have 1 more laptop here which I need to share the internet connection with. In Windows 7 I do this with the Connectify program, and in Ubuntu I have seen that you can do things like set up hotspots etc. But because I am using WvDial I am not sure how I would share the internet. I am only beginning to use Ubuntu but unfortunately until I can figure out how to share the internet over WiFi when connected via WvDial I have to stick with Windows. If you have any ideas on how to do this it would be much appreciated!

  Read the article

• What does RESTful web applications mean? [closed]

  - by John Cooper

  Possible Duplicate: What is REST (in simple English) What does RESTful web applications mean? A web service is a function that can be accessed by other programs over the web (Http). To clarify a bit, when you create a website in PHP that outputs HTML its target is the browser and by extension the human being reading the page in the browser. A web service is not targeted at humans but rather at other programs. SOAP and REST are two ways of creating WebServices. Correct me if i am wrong? What are other ways i can create a WebService? What does it mean fully RESTful web Application?

  Read the article

• WebFX: Running JavaFX as web page

  - by Bruno.Borges

  This weekend I wanted to learn JavaFX, so I decided to code an idea I had a few years ago when I first saw JavaFX Script. So I started coding a web browser that runs HTML with the awesome, HTML5 supported WebView. But this browser also offers one extra feature: it loads FXML files as if they were HTML. So instead of defining your web page with HTML and running with WebKit, you can define a web page with FXML+CSS+JS and run as a JavaFX application. The project is called WebFX and already has a prototype on GitHub. I also uploaded a video on YouTube demonstrating the idea. What do you think about using JavaFX in the future for web pages, instead of HTML?

  Read the article

• Xrandr settings don't stick; bash script fails; Nvidia; disper doesn't work

  - by bcmcfc

  I have an Nvidia graphics card. Yeah, I know. This might have to change soon. I am trying to get the resolution to set correctly on my second monitor, which is a VGA monitor with a native resolution of 1440x900. I have set up this bash script which doesn't work: xrandr --newmode "1440" 106.50 1440 1528 1672 1904 900 903 909 934 -hsync +vsync xrandr --addmode -display VGA-1 1440 xrandr --output VGA-1 --mode 1440 It outputs: xrandr: cannot find mode 1440. It has worked previously when running the commands individually but after a restart it fails. I've also just installed disper as per this question but have no idea how to use it - the help suggests the command: disper -d VGA-1 -r "1440x900" should work, but it does not. It just outputs the help text, suggesting something is wrong but not saying what. Is there any way to get these horrific Nvidia drivers working properly with a resolution that is not detected by the tools?

  Read the article

• Are there efforts to build a collaboratively edited HTML/JS/DOM reference?

  - by Pekka

  W3Schools has a reputation of being incomplete, sometimes incorrect, and ridden with advertising; still, when looking to look up some things or link to documentation when answering a SO question, it still is the only handy cross-browser resource. There are other resources like the Mozilla Developer Network that is doing an increasingly great job documenting JavaScript, and the legendary and great Quirksmode. But they, as brilliant as they are, cover only parts of the areas I am talking about, and provide no community editing and quality control options. Is anybody aware of efforts to create a collaboratively edited, cross-browser HTML/CSS/JavaScript/DOM encyclopedia? If you will, I'm thinking of a challenger to W3Schools like SO was to Experts Exchange. (I thought this more suitable on Programmers than on SO proper - please correct me if I'm wrong.)

  Read the article

• What is bondib1 used for on SPARC SuperCluster with InfiniBand, Solaris 11 networking & Oracle RAC?

  - by user12620111

  A co-worker asked the following question about a SPARC SuperCluster InfiniBand network: > on the database nodes the RAC nodes communicate over the cluster_interconnect. This is the > 192.168.10.0 network on bondib0. (according to ./crs/install/crsconfig_params NETWORKS> setting) > What is bondib1 used for? Is it a HA counterpart in case bondib0 dies? This is my response: Summary: bondib1 is currently only being used for outbound cluster interconnect interconnect traffic. Details: bondib0 is the cluster_interconnect $ oifcfg getif            bondeth0  10.129.184.0  global  public bondib0  192.168.10.0  global  cluster_interconnect ipmpapp0  192.168.30.0  global  public bondib0 and bondib1 are on 192.168.10.1 and 192.168.10.2 respectively. # ipadm show-addr | grep bondi bondib0/v4static  static   ok           192.168.10.1/24 bondib1/v4static  static   ok           192.168.10.2/24 Hostnames tied to the IPs are node1-priv1 and node1-priv2  # grep 192.168.10 /etc/hosts 192.168.10.1    node1-priv1.us.oracle.com   node1-priv1 192.168.10.2    node1-priv2.us.oracle.com   node1-priv2 For the 4 node RAC interconnect: Each node has 2 private IP address on the 192.168.10.0 network. Each IP address has an active InfiniBand link and a failover InfiniBand link. Thus, the 4 node RAC interconnect is using a total of 8 IP addresses and 16 InfiniBand links. bondib1 isn't being used for the Virtual IP (VIP): $ srvctl config vip -n node1 VIP exists: /node1-ib-vip/192.168.30.25/192.168.30.0/255.255.255.0/ipmpapp0, hosting node node1 VIP exists: /node1-vip/10.55.184.15/10.55.184.0/255.255.255.0/bondeth0, hosting node node1 bondib1 is on bondib1_0 and fails over to bondib1_1: # ipmpstat -g GROUP       GROUPNAME   STATE     FDT       INTERFACES ipmpapp0    ipmpapp0    ok        --        ipmpapp_0 (ipmpapp_1) bondeth0    bondeth0    degraded  --        net2 [net5] bondib1     bondib1     ok        --        bondib1_0 (bondib1_1) bondib0     bondib0     ok        --        bondib0_0 (bondib0_1) bondib1_0 goes over net24 # dladm show-link | grep bond LINK                CLASS     MTU    STATE    OVER bondib0_0           part      65520  up       net21 bondib0_1           part      65520  up       net22 bondib1_0           part      65520  up       net24 bondib1_1           part      65520  up       net23 net24 is IB Partition FFFF # dladm show-ib LINK         HCAGUID         PORTGUID        PORT STATE  PKEYS net24        21280001A1868A  21280001A1868C  2    up     FFFF net22        21280001CEBBDE  21280001CEBBE0  2    up     FFFF,8503 net23        21280001A1868A  21280001A1868B  1    up     FFFF,8503 net21        21280001CEBBDE  21280001CEBBDF  1    up     FFFF On Express Module 9 port 2: # dladm show-phys -L LINK              DEVICE       LOC net21             ibp4         PCI-EM1/PORT1 net22             ibp5         PCI-EM1/PORT2 net23             ibp6         PCI-EM9/PORT1 net24             ibp7         PCI-EM9/PORT2 Outbound traffic on the 192.168.10.0 network will be multiplexed between bondib0 & bondib1 # netstat -rn Routing Table: IPv4   Destination           Gateway           Flags  Ref     Use     Interface -------------------- -------------------- ----- ----- ---------- --------- 192.168.10.0         192.168.10.2         U        16    6551834 bondib1   192.168.10.0         192.168.10.1         U         9    5708924 bondib0   There is a lot more traffic on bondib0 than bondib1 # /bin/time snoop -I bondib0 -c 100 > /dev/null Using device ipnet/bondib0 (promiscuous mode) 100 packets captured real        4.3 user        0.0 sys         0.0 (100 packets in 4.3 seconds = 23.3 pkts/sec) # /bin/time snoop -I bondib1 -c 100 > /dev/null Using device ipnet/bondib1 (promiscuous mode) 100 packets captured real       13.3 user        0.0 sys         0.0 (100 packets in 13.3 seconds = 7.5 pkts/sec) Half of the packets on bondib0 are outbound (from self). The remaining packet are split evenly, from the other nodes in the cluster. # snoop -I bondib0 -c 100 | awk '{print $1}' | sort | uniq -c Using device ipnet/bondib0 (promiscuous mode) 100 packets captured   49 node1-priv1.us.oracle.com   24 node2-priv1.us.oracle.com   14 node3-priv1.us.oracle.com   13 node4-priv1.us.oracle.com 100% of the packets on bondib1 are outbound (from self), but the headers in the packets indicate that they are from the IP address associated with bondib0: # snoop -I bondib1 -c 100 | awk '{print $1}' | sort | uniq -c Using device ipnet/bondib1 (promiscuous mode) 100 packets captured  100 node1-priv1.us.oracle.com The destination of the bondib1 outbound packets are split evenly, to node3 and node 4. # snoop -I bondib1 -c 100 | awk '{print $3}' | sort | uniq -c Using device ipnet/bondib1 (promiscuous mode) 100 packets captured   51 node3-priv1.us.oracle.com   49 node4-priv1.us.oracle.com Conclusion: bondib1 is currently only being used for outbound cluster interconnect interconnect traffic.

  Read the article

• Nautilus uses different permissions for mounted drives

  - by farhad0011

  I've written two bash scripts to give read-only or read/write access to my NTFS partition: read-only access: sudo umount /media/Data_Drive/ sudo mount -t ntfs-3g -o ro,user,auto,nls=utf8,umask=0000,uid=1000 /dev/sda2 /media/Data_Drive read/write access: sudo umount /media/Data_Drive/ sudo mount -t ntfs-3g -o rw,user,auto,nls=utf8,umask=0000,uid=1000 /dev/sda2 /media/Data_Drive It works perfectly if I only use terminal to work with the files. It also works with Nautilus in read-only mode but not in the read/write mode. In fact, Nautilus gives me an error when I try to copy a file to Data_Drive saying "The destination is read-only". More funny, when I look at the permissions (by right-clicking on Data_Drive and then properties-permissions) I have all the required permissions to write a file in Data_Drive! I am so confused why Nautilus behaves strangely. I appreciate if anybody could solve the mystery!

  Read the article

• Can't boot Ubuntu 12.10 graphics problem

  - by Frantumn

  I can't boot since installing Ubuntu 12.10 When I try to run Ubuntu My computer never gets to the Ubuntu screen with the loading dots. I tried to run in recovery mode with safe graphics (failsafex) When I do this a message pops up saying "the system is running in low graphics mode", If I click okay I am asked what would I like to do and am given four options. I tried running low graphics for one session and then a message appears with a progress bar and says standby one minute while the display restarts. The progress bar never moves and if I click okay the whole process just restarts. I Don't know what to do from here I can't get into the OS. I'm not sure whether the problem is related to compatibility with my laptop monitor or my graphic card nvidia360m I had to install using a safe graphics mode. To learn about how I installed see this link. This link also has information on my computer hardware. Can't install Ubuntu since 10.10 ----UPDATE--- I was able to get into a desktop environment By installing Nvidia-current however it is messy. I have a screen and I am able to see my desktop however there is no unity bar and none of the keyboard controls work. I can right click and create a folder on the desktop and then I can see inside that folder in a traditional browser window. There is still no top menu or unity bar. When I boot normally I don't get into the desktop environment and I get this message in tty 'GPU lockup switching to software FBCON' Okay, I've played around with tips the pages from comments. I've been able to consistantly get into a safemode desktop environment using the xorg & nouveau drivers. I've tried switching between the 5 different options in the Additional Drivers tab in Software Sources. The nVidia (proprietary, tested) driver gets beyond the GPU lockup on a normal boot and actually gets into a Desktop. The issue is then that there is no Unity bar, or top screen menu bar and the resolution is very low. I've tried switching to the (prop, tested) driver and then reinstalling Unity and Ubuntu-Desktop but that didn't work either.

  Read the article

• Google Chrome Gets Security, IE Frame Updates

  The browser gets bumped to version 5.0.375.70, while Chrome Frame goes to beta.

  Read the article

• fdisk shows overlapping partitions

  - by Campa

  At every boot to start Ubuntu, a partition gets re-mounted more than 1 times, sometimes causing very long boots. Example below: > dmesg ... [ 21.472020] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro ... [ 42.021537] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0 ... I suspect there is a problem of overlapping partitions here, regarding sda4 and sda5: > sudo fdisk -l Device Boot Start End Blocks Id System /dev/sda1 63 610469 305203+ de Dell Utility /dev/sda2 612352 32069631 15728640 7 HPFS/NTFS/exFAT /dev/sda3 * 32069632 238979788 103455078+ 7 HPFS/NTFS/exFAT /dev/sda4 238983166 625141759 193079297 5 Extended /dev/sda5 238983168 612630527 186823680 83 Linux /dev/sda6 612632576 625141759 6254592 82 Linux swap / Solaris Further details: > more /etc/fstab ... # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda6 during installation UUID=b33be99b-5c9e-449e-ad48-be608aeff001 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda7 during installation UUID=7c9071cc-b77b-40da-9f80-6b8a9a220cb1 none swap sw and > mount /dev/sda5 on / type ext4 (rw,errors=remount-ro,commit=0) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) fusectl on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/piero/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=piero) I am Running Ubuntu Oneiric + LXDE on Dell Studio XPS machine 64-bit, dual booting with Windows 7. A months ago, I resized the Ubuntu partition and maybe I messed up something by doing that. Do you have any idea, why this long booting is happening?

  Read the article

• Windows 8 Install

  - by Richard Jones

  So did my first Windows 8 install today. Did it on a Macbook Pro (bootcamp partition). Bootcamp partition, needed to be formatted by Windows 8, in-order to proceed. However once done install went smoothly. Installed the Apple Windows Support stuff in compatibility mode; which went well. I tried it first not in compatibility mode and it caused a Blue Screen of death (which now has a :-( icon ) The volume, brightness etc. soft keys work well. I had some trouble joining wireless networks; so hopefully a windows update will resolve. First impression, is that 'its just like Windows 7', but with Metro. We'll see what happens over the next few days.

  Read the article

• Test Driven Development Code Order

  - by Bobby Kostadinov

  I am developing my first project using test driven development. I am using Zend Framework and PHPUnit. Currently my project is at 100% code coverage but I am not sure I understand in what order I am supposed to write my code. Am I supposed to write my test FIRST with what my objects are expected to do or write my objects and then test them? Ive been working on completing a controller/model and then writing at test for it but I am not sure this is what TDD is about? Any advice? For example, I wrote my Auth plugin and my Auth controller and tested that they work properly in my browser, and then I sat down to write the tests for them, which proved that there were some logical errors in the code that did work in the browser.

  Read the article

• Attach a Wordpress.org blog to my BigCommerece Store as a sub-domain

  - by user1323814

  I am stuck in a peculiar situation. I have a store on BigCommerece configured with a domain from GoDaddy (mystore.com). I recently created a custom wordpress blog and hosted it on 1and1 hosting (s418783372.onlinehome.us), since bigcommerece can't host Wordpress. Now I want to use it from a sub-domain of my main-bigcommerece store (models.mystore.com), but it doesn't seem to be working since BigCommerce is the Doman Manager, but GoDaddy is the Domain-Registrar and 1and1 is the host so it doesn't control the domain. I have tried setting up a CNAME record on BigCommerece and when it didn't work asked BigCommerece about it, but they said they can't do anything about it since they aren't the domain registrar and gave me a message saying: The responsiblity to show the name in the browser on the site is up to the server or site admin. The Cname can only get the browser there

  Read the article

• Is obtrusive JavaScript ever ok?

  - by Petah

  I was thinking that if all the users of a website are required to have JavaScript enabled, Is it ok to use obtrusive JavaScript? I'm all for progressive enhancement, but whats the point when an advanced web applications bounces users at the door if they have an old browser or JavaScript disabled? We have a very slim target audience, and we can tell our target audience what browser and plugins/functionality they are required to have. So you my question is, is mixing JS and HTML alright in that case. Like using onclick attributes.

  Read the article

• How to modify the default position of desktop icons

  - by Hanynowsky

  Is it possible to modify the default desktop icons position so that icons move a little bit to right. If yes, how? As far as I know, there is no tweak for that in Nautilus. When I click "Organize Desktop by Name", the icons get aligned to the left of Desktop: that's fine, but they're too close to the launcher when it's in AUTO HIDE mode. So when Launcher is revealed, it comes over icons. Reproduce: Download some files from your browser or copy files/folders from a folder to the desktop, then these latter will be placed just like the screenshot. Their position is fine when the launcher is hidden, but when revealed, it hides a part of the icons. There is no problem when LAUNCHER AUTO-HIDE MODE is disabled. Thanks in advance.

  Read the article

• After the update today no graphical interface anymore - 12.04

  - by Mark

  I installed the updates through the update manager today. I shut down my Laptop and now after starting it up again, I only get terminal access to advices. Grub is loading fine and after I picked Ubuntu 12.04 the screen get blank and I am asked to log in with my username and password in command line mode. If I log in I am still in command line mode. How do I get the "normal (graphical)" Ubuntu back? I hope you know what I mean. Since English is not my first language I can't explain this the way I would like to. Mark

  Read the article

• Windows 7 doesnt boot after installing Ubuntu 12.10 (Asus Zenbook Prime / UEFI problem)

  - by jpdus

  Today I installed Ubuntu and since then i cannot boot into Windows anymore. I used the "standard" option (didnt change any partitions manually, just entered the size) but used the UEFI-mode. At first the GRUB entries for Windows did not work at all, after reading this thead i was able to add a new Grub entry - now i can get into the "windows-loading" screen for a few seconds but then i always see some kind of bluescreen for a fraction of a second and the laptop reboots. I can get into the windows recovery partition but the only option there is to reset everything to factory settings (+erase all data). I have no idea how to get into the Windows 7 repair mode which was mentioned here (tried everything else in this thread too - no success). My boot info can be found here: http://paste.ubuntu.com/1411573/ I have no idea what went wrong (there is even an extra page for the Zenbook Prime where no installation problems are mentioned). I would appreciate any help/ideas, many thanks!

  Read the article

• What is the best practice for website design and markup now that mobile browsers are common?

  - by Jonathan Drain

  Back in 2008, smartphones were a small market and it was commonplace for sites to be designed for a fixed width - say, 900px or 960px - with the page centered if the browser window was larger. Many designers said fluid width was better, but since user screens typically varied between 1024x768 and 1920x1080, fluid width allowed longer line length than is optimal for ease of reading, and so many sites (including Stack Exchange) use fixed width. Now that mobile devices are common, what is the the best approach to support both desktop and mobile browsers? Establish a separate mobile site (e.g: mobile.example.com) Serve a different CSS to mobile devices; if so how? Server-side browser sniffing, or a @media rule? Use Javascript or something to adapt the website dynamically to the client? Should all websites be expected to be responsive? Some kind of fluid layout Something else?

  Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >