Search Results

Search found 12790 results on 512 pages for 'port islander 2009'.

Page 265/512 | < Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >

  • Yet again: "This device can perform faster" (Samsung Galaxy Tab 2)

    - by Mike C
    I've been doing a lot of research with no reasonable solution. Please excuse the length of my post. When I plug my Galaxy Tab 2 (7" / Wi-Fi only / Android ICS) into my Windows 7 64-bit machine, I (almost always) get this warning popup that "This device can perform faster." And in fact, transfers onto the Tab in this mode are slow. The two times I've been able to get a high-speed connection, the transfer has occurred at the expected speed. I just don't know what to do to get that high-speed transfer. (The first time I did, it was the first time I connected the Tab; the second time I did, I was fiddling around and unplugging/plugging in again.) That popup is telling me that the device is USB2, but that it thinks I've connected to a USB1 port. In fact, every USB port (there are ten) on this system is USB2. It's an ASUS M3A78-EMH mobo from late 2008. I'm not sure what the chipset is; the CPU is an AMD Athlon 4850e, but I've seen this message reported for non-AMD systems. (Every mobo reference I've seen in reports on this has been for Asus, but of course most reporters aren't reporting that info at all.) The Windows 7 installation is just a couple weeks old (I had a disk crash) but I saw the same warning on the WinXP/64 that was installed previously. In Device Manager, there are two "Standard Enhanced PCI to USB Host Controller" nodes which are the actual high-speed controllers. There are also five "Standard OpenHCD USB Host Controller" nodes, which I have determined are virtual USB1 controllers embedded in the "Enhanced" controllers. (In Device Manager, I'm using View|Devices by Connection.) My high-speed thumb drives, external disks, and iPod all show up as subnodes of the "Enhanced" controllers; the keyboard, mouse, and USB speakers under the "OpenHCD" ones -- and this is true no matter which ports these devices are plugged into. The Tab shows up under an OpenHCD node, unsurprisingly. It appears as a threesome: a top-level "Mobile USB Composite device" with two subs: "Galaxy Tab 2" and "Mobile USB Modem." (I have no idea what the modem device implies or how I might use it, but I don't care about it either: I just want the Tab to reliably connect at high speed.) On the Tab, the USB support has a switch between PTP and MTP, the latter being the default, and the preferred mode for me (as I'm usually hooking it up for music synch). I have tried, however, connecting it as PTP, and it still connects as USB 1. (As PTP, only the "Galaxy Tab 2" device appears -- no Composite, no Modem.) If it's plugged in as MTP and I change the setting to PTP, Windows unloads and reloads the device, and voila: The Tab appears under an "Enhanced" node, but eventually re-loads again to show a exclamation icon on the device; Properties then shows "This device cannot start." Same response if I plug it in as PTP and then change to MTP; in this case, only the Tab itself shows the exclamation, not the other two devices. One thing I have not tried, and really would prefer to avoid, is installing the "beta" chipset driver available on the Asus website, which is dated 2009. Windows tells me it has the most up-to-date drivers for the Tab, and for the chipset, and I'm inclined to believe that. I suspect the problem is with the Samsung drivers, or possibly the hardware. One suggestion I saw elsewhere which might, possibly, pertain is to ensure the USB cable is properly shielded; however, the Tab has one of those misbegotten 30-pin, not-quite-an-iPod connectors; I don't know if I could find a 3rd party one. It seems unlikely that this cable is improperly shielded, tho. (Is there a way to test that?) So, my question is: does anyone know how to get this working as one might reasonably expect it to?

    Read the article

  • Ubuntu, No wireless networks found after correctly installed madwifi

    - by Peter
    Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

    Read the article

  • LDAP over SSL with an EFI Fiery printer

    - by austinian
    I've got a printer with a Fiery running 8e Release 2. I can authenticate users against AD using the LDAP configuration, but I can only get it to work if I don't use SSL/TLS, and only if I use SIMPLE authentication. Right now, it's authenticating using a fairly low-impact user, but it's also the only system on our network that's not using LDAPS. I can get AD info fine over LDAPS using ldp.exe from my machine, our firewall, our mail filter, our linux boxes, etc. The only problem child is the Fiery. I've added the LDAP server certificate as a trusted cert to the Fiery, but after I check the box for Secure Communication and change the port to 636, pressing Validate results in a dialog box coming up saying: LDAP Validation Failed Server Name invalid or server is unavailable. I've tried changing the server name to use just the name, the FQDN, and the IP address, and changed it to another server, just to see if it was just this AD server that was fussy with the Fiery. EDIT: removed LDP output, added packet capture analysis from wireshark: The conversation seems pretty normal to me, up to the point where the Fiery terminates the connection after the server sends back a handshake response. Maybe they messed up their TLS implementation? I'm trying support, but it's been fairly useless so far. The cert is a SHA-2 (sha256RSA) 2048-bit certificate. Also, it looks like the Fiery is specifying TLS 1.0. Looking at http://msdn.microsoft.com/en-us/library/windows/desktop/aa374757(v=vs.85).aspx, I'm not seeing SHA256 and TLS 1.0 combination being supported by SChannel. headdesk perhaps that's why, after the DC changes the cipher spec, the connection is terminated by the Fiery? TLS 1.1 and 1.2 are enabled on the DC. Wireshark conversation: DC: 172.17.2.22, Fiery: 172.17.2.42 No. Time Source Source Port Destination Destination Port Protocol Length Info 1 0.000000000 172.17.2.42 48633 172.17.2.22 ldaps TCP 74 48633 > ldaps [SYN] Seq=0 Win=5840 Len=0 MSS=1460 SACK_PERM=1 TSval=3101761 TSecr=0 WS=4 2 0.000182000 Dell_5e:94:e3 Broadcast ARP 60 Who has 172.17.2.42? Tell 172.17.2.22 3 0.000369000 TyanComp_c9:0f:90 Dell_5e:94:e3 ARP 60 172.17.2.42 is at 00:e0:81:c9:0f:90 4 0.000370000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 74 ldaps > 48633 [SYN, ACK] Seq=0 Ack=1 Win=8192 Len=0 MSS=1460 WS=256 SACK_PERM=1 TSval=67970573 TSecr=3101761 5 0.000548000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=1 Ack=1 Win=5840 Len=0 TSval=3101761 TSecr=67970573 6 0.001000000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 147 Client Hello 7 0.001326000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 8 0.001513000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 9 0.001515000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=1449 Win=8736 Len=0 TSval=3101761 TSecr=67970573 10 0.001516000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=2897 Win=11632 Len=0 TSval=3101761 TSecr=67970573 11 0.001732000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 12 0.001737000 172.17.2.22 ldaps 172.17.2.42 48633 TLSv1 1243 Server Hello, Certificate, Certificate Request, Server Hello Done 13 0.001738000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=4345 Win=14528 Len=0 TSval=3101761 TSecr=67970573 14 0.001739000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=5522 Win=17424 Len=0 TSval=3101761 TSecr=67970573 15 0.002906000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 78 Certificate 16 0.004155000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 333 Client Key Exchange 17 0.004338000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5522 Ack=361 Win=66304 Len=0 TSval=67970573 TSecr=3101762 18 0.004338000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 72 Change Cipher Spec 19 0.005481000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 327 Encrypted Handshake Message 20 0.005645000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5522 Ack=628 Win=66048 Len=0 TSval=67970574 TSecr=3101762 21 0.010247000 172.17.2.22 ldaps 172.17.2.42 48633 TLSv1 125 Change Cipher Spec, Encrypted Handshake Message 22 0.016451000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [FIN, ACK] Seq=628 Ack=5581 Win=17424 Len=0 TSval=3101765 TSecr=67970574 23 0.016630000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5581 Ack=629 Win=66048 Len=0 TSval=67970575 TSecr=3101765 24 0.016811000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 60 ldaps > 48633 [RST, ACK] Seq=5581 Ack=629 Win=0 Len=0

    Read the article

  • vSphere ESX 5.5 hosts cannot connect to NFS Server

    - by Gerald
    Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

    Read the article

  • Disable error_log. Error_log flooding

    - by user36646
    Hello, i got an webserver running and old version of gambio (xt:commerce fork). The error_log in the dir over the public_html is flooding with errors. About 30mb in 15min. How can I disable this log? I can't fix all the errors. Here are a few examples of the errors: [warn] mod_fcgid: stderr: PHP Notice: Undefined variable: key in /usr/www/users/foo//includes/classes/class.inputfilter.php on line 98 [warn] mod_fcgid: stderr: PHP Notice: Undefined index: in /usr/www/users/foo/templ [warn] mod_fcgid: stderr: in /usr/www/users/foo/templates/gambio/source/inc/xtc_show_category_sectionc.inc.php on line 47 They are all errors of: "mod_fcgid: stderr". I tried to grep "error_log" and "error_report" in the public html dir, but i did not find anything. Here is a part from the phpinfo(): PHP Version 4.4.9 System Linux foobar.com 2.6.26-2-686-bigmem #1 SMP Sat Dec 26 09:26:36 UTC 2009 i686 Build Date Feb 11 2010 13:00:33 Configure Command './configure' '--prefix=/usr/local/php4' '--with-config-file-path=/etc/php4/cgi' '--with-gd' '--with-jpeg-dir' '--with-png-dir' '--with-tiff-dir' '--with-ttf' '--enable-force-cgi-redirect' '--enable-safe-mode' '--with-zlib' '--enable-ftp' '--enable-url-includes' '--enable-gd-native-ttf' '--enable-trans-sid' '--enable-dbase' '--with-db4' '--with-ldap' '--enable-bcmath' '--enable-calendar' '--enable-memory-limit' '--with-mcal=/usr' '--with-bz2' '--with-mod-dav' '--enable-sockets' '--with-kerberos' '--with-imap-ssl' '--enable-gd-imgstrttf' '--with-freetype-dir' '--with-curl' '--with-mysql' '--with-mhash' '--with-gdbm' '--with-pgsql' '--with-gettext' '--with-xml' '--with-mcrypt' '--with-openssl' '--with-dom' '--without-pear' '--enable-exif' '--with-zip' '--enable-wddx' '--disable-cli' '--enable-fastcgi' '--with-imap' '--enable-xslt' '--with-xslt-sablot=/usr/local/lib' '--enable-mbstring' '--with-dom-xslt' '--with-dom-exslt' Server API CGI/FastCGI Virtual Directory Support disabled Configuration File (php.ini) Path /home/httpd/php-ini/foo/php.ini PHP API 20020918 PHP Extension 20020429 Zend Extension 20050606 Debug Build no Zend Memory Manager enabled Thread Safety disabled Registered PHP Streams php, http, ftp, https, ftps, compress.bzip2, compress.zlib **Configuration PHP Core** Directive Local Value Master Value allow_call_time_pass_reference On On allow_url_fopen Off Off always_populate_raw_post_data Off Off arg_separator.input & & arg_separator.output & & asp_tags Off Off auto_append_file no value no value auto_prepend_file no value no value browscap no value no value default_charset no value no value default_mimetype text/html text/html define_syslog_variables Off Off disable_classes no value no value disable_functions no value no value display_errors On On display_startup_errors Off Off doc_root no value no value docref_ext no value no value docref_root no value no value enable_dl On On error_append_string no value no value error_log no value no value error_prepend_string no value no value error_reporting 2039 2039 expose_php On On extension_dir /usr/local/php4/lib/php/extensions/no-debug-non-zts-20020429 /usr/local/php4/lib/php/extensions/no-debug-non-zts-20020429 file_uploads On On gpc_order GPC GPC highlight.bg #FFFFFF #FFFFFF highlight.comment #FF8000 #FF8000 highlight.default #0000BB #0000BB highlight.html #000000 #000000 highlight.keyword #007700 #007700 highlight.string #DD0000 #DD0000 html_errors On On ignore_repeated_errors Off Off ignore_repeated_source Off Off ignore_user_abort Off Off implicit_flush Off Off include_path .:/usr/local/lib/php/ .:/usr/local/lib/php/ log_errors Off Off log_errors_max_len 1024 1024 magic_quotes_gpc On On magic_quotes_runtime Off Off magic_quotes_sybase Off Off max_execution_time 120 120 max_input_nesting_level 500 500 max_input_time -1 -1 memory_limit 128000000 128000000 open_basedir /usr/www/users/foo:/usr/home/foo:/tmp:/usr/local/lib/php:/usr/local/rmagic:/usr/www/users/he/_system_ /usr/www/users/foo:/usr/home/foo:/tmp:/usr/local/lib/php:/usr/local/rmagic:/usr/www/users/he/_system_ output_buffering no value no value output_handler no value no value post_max_size 128000000 128000000 precision 14 14 register_argc_argv On On register_globals Off Off report_memleaks On On safe_mode Off Off safe_mode_exec_dir no value no value safe_mode_gid Off Off safe_mode_include_dir no value no value sendmail_from no value no value sendmail_path /usr/sbin/sendmail -t /usr/sbin/sendmail -t serialize_precision 100 100 short_open_tag On On SMTP localhost localhost smtp_port 25 25 sql.safe_mode Off Off track_errors Off Off unserialize_callback_func no value no value upload_max_filesize 128000000 128000000 upload_tmp_dir /usr/foo/foo/.tmp /usr/foo/.tmp user_dir no value no value variables_order EGPCS EGPCS xmlrpc_error_number 0 0 xmlrpc_errors Off Off y2k_compliance Off Off

    Read the article

  • Can't connect to smtp (postfix, dovecot) after making a change and trying to change it back

    - by UberBrainChild
    I am using postfix and dovecot along with zpanel and I tried enabling SSL and then turned it off as I did not have SSL configured yet and I realized it was a bit stupid at the time. I am using CentOS 6.4. I get the following error in the mail log. (I changed my host name to "myhostname" and my domain to "mydomain.com") Oct 20 01:49:06 myhostname postfix/smtpd[4714]: connect from mydomain.com[127.0.0.1] Oct 20 01:49:16 myhostname postfix/smtpd[4714]: fatal: no SASL authentication mechanisms Oct 20 01:49:17 myhostname postfix/master[4708]: warning: process /usr/libexec/postfix/smtpd pid 4714 exit status 1 Oct 20 01:49:17 amyhostname postfix/master[4708]: warning: /usr/libexec/postfix/smtpd: bad command startup -- throttling Reading on forums and similar questions I figured it was just a service that was not running or installed. However I can see that saslauthd is currently up and running on my system and restarting it does not help. Here is my postfix master.cf # # Postfix master process configuration file. For details on the format # of the file, see the Postfix master(5) manual page. # # ***** Unused items removed ***** # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd # -o content_filter=smtp-amavis:127.0.0.1:10024 # -o receive_override_options=no_address_mappings pickup fifo n - n 60 1 pickup submission inet n - - - - smtpd -o content_filter= -o receive_override_options=no_header_body_checks cleanup unix n - n - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - n 300 1 oqmgr tlsmgr unix - - n 1000? 1 tlsmgr rewrite unix - - n - - trivial-rewrite bounce unix - - n - 0 bounce defer unix - - n - 0 bounce trace unix - - n - 0 bounce verify unix - - n - 1 verify flush unix n - n 1000? 0 flush proxymap unix - - n - - proxymap smtp unix - - n - - smtp smtps inet n - - - - smtpd # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - n - - smtp -o fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - n - - showq error unix - - n - - error discard unix - - n - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - n - - lmtp anvil unix - - n - 1 anvil scache unix - - n - 1 scache # # ==================================================================== # Interfaces to non-Postfix software. Be sure to examine the manual # pages of the non-Postfix software to find out what options it wants. # ==================================================================== maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/local/bin/maildrop -d ${recipient} uucp unix - n n - - pipe flags=Fqhu user=uucp argv=uux -r -n -z -a$sender - $nexthop!rmail ($recipient) ifmail unix - n n - - pipe flags=F user=ftn argv=/usr/lib/ifmail/ifmail -r $nexthop ($recipient) bsmtp unix - n n - - pipe flags=Fq. user=foo argv=/usr/local/sbin/bsmtp -f $sender $nexthop $recipient # # spam/virus section # smtp-amavis unix - - y - 2 smtp -o smtp_data_done_timeout=1200 -o disable_dns_lookups=yes -o smtp_send_xforward_command=yes 127.0.0.1:10025 inet n - y - - smtpd -o content_filter= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks=127.0.0.0/8 -o smtpd_error_sleep_time=0 -o smtpd_soft_error_limit=1001 -o smtpd_hard_error_limit=1000 -o receive_override_options=no_header_body_checks -o smtpd_bind_address=127.0.0.1 -o smtpd_helo_required=no -o smtpd_client_restrictions= -o smtpd_restriction_classes= -o disable_vrfy_command=no -o strict_rfc821_envelopes=yes # # Dovecot LDA dovecot unix - n n - - pipe flags=DRhu user=vmail:mail argv=/usr/libexec/dovecot/deliver -d ${recipient} # # Vacation mail vacation unix - n n - - pipe flags=Rq user=vacation argv=/var/spool/vacation/vacation.pl -f ${sender} -- ${recipient} And here is dovecot ## ## Dovecot config file ## listen = * disable_plaintext_auth = no protocols = imap pop3 lmtp sieve auth_mechanisms = plain login passdb { driver = sql args = /etc/zpanel/configs/dovecot2/dovecot-mysql.conf } userdb { driver = sql } userdb { driver = sql args = /etc/zpanel/configs/dovecot2/dovecot-mysql.conf } mail_location = maildir:/var/zpanel/vmail/%d/%n first_valid_uid = 101 #last_valid_uid = 0 first_valid_gid = 12 #last_valid_gid = 0 #mail_plugins = mailbox_idle_check_interval = 30 secs maildir_copy_with_hardlinks = yes service imap-login { inet_listener imap { port = 143 } } service pop3-login { inet_listener pop3 { port = 110 } } service lmtp { unix_listener lmtp { #mode = 0666 } } service imap { vsz_limit = 256M } service pop3 { } service auth { unix_listener auth-userdb { mode = 0666 user = vmail group = mail } # Postfix smtp-auth unix_listener /var/spool/postfix/private/auth { mode = 0666 user = postfix group = postfix } } service auth-worker { } service dict { unix_listener dict { mode = 0666 user = vmail group = mail } } service managesieve-login { inet_listener sieve { port = 4190 } service_count = 1 process_min_avail = 0 vsz_limit = 64M } service managesieve { } lda_mailbox_autocreate = yes lda_mailbox_autosubscribe = yes protocol lda { mail_plugins = quota sieve postmaster_address = [email protected] } protocol imap { mail_plugins = quota imap_quota trash imap_client_workarounds = delay-newmail } lmtp_save_to_detail_mailbox = yes protocol lmtp { mail_plugins = quota sieve } protocol pop3 { mail_plugins = quota pop3_client_workarounds = outlook-no-nuls oe-ns-eoh } protocol sieve { managesieve_max_line_length = 65536 managesieve_implementation_string = Dovecot Pigeonhole managesieve_max_compile_errors = 5 } dict { quotadict = mysql:/etc/zpanel/configs/dovecot2/dovecot-dict-quota.conf } plugin { # quota = dict:User quota::proxy::quotadict quota = maildir:User quota acl = vfile:/etc/dovecot/acls trash = /etc/zpanel/configs/dovecot2/dovecot-trash.conf sieve_global_path = /var/zpanel/sieve/globalfilter.sieve sieve = ~/dovecot.sieve sieve_dir = ~/sieve sieve_global_dir = /var/zpanel/sieve/ #sieve_extensions = +notify +imapflags sieve_max_script_size = 1M #sieve_max_actions = 32 #sieve_max_redirects = 4 } log_path = /var/log/dovecot.log info_log_path = /var/log/dovecot-info.log debug_log_path = /var/log/dovecot-debug.log mail_debug=yes ssl = no Does anyone have any ideas or tips on what I can try to get this working? Thanks for all the help EDIT: Output of postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix debug_peer_level = 2 delay_warning_time = 4 disable_vrfy_command = yes html_directory = no inet_interfaces = all mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = localhost.$mydomain, localhost mydomain = control.yourdomain.com myhostname = control.yourdomain.com mynetworks = all newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.2.2/README_FILES recipient_delimiter = + relay_domains = proxy:mysql:/etc/zpanel/configs/postfix/mysql-relay_domains_maps.cf sample_directory = /usr/share/doc/postfix-2.2.2/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtp_use_tls = no smtpd_client_restrictions = smtpd_data_restrictions = reject_unauth_pipelining smtpd_helo_required = yes smtpd_helo_restrictions = smtpd_recipient_restrictions = permit_sasl_authenticated, permit_mynetworks, reject_unauth_destination, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_recipient_domain smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_sender_restrictions = smtpd_use_tls = no soft_bounce = yes transport_maps = hash:/etc/postfix/transport unknown_local_recipient_reject_code = 550 virtual_alias_maps = proxy:mysql:/etc/zpanel/configs/postfix/mysql-virtual_alias_maps.cf, regexp:/etc/zpanel/configs/postfix/virtual_regexp virtual_gid_maps = static:12 virtual_mailbox_base = /var/zpanel/vmail virtual_mailbox_domains = proxy:mysql:/etc/zpanel/configs/postfix/mysql-virtual_domains_maps.cf virtual_mailbox_maps = proxy:mysql:/etc/zpanel/configs/postfix/mysql-virtual_mailbox_maps.cf virtual_minimum_uid = 101 virtual_transport = dovecot virtual_uid_maps = static:101

    Read the article

  • HTTP downloads stop after some time, resuming is not possible

    - by cdauth
    When I try to download a file via HTTP, the downloads sometimes stop after around 30 MB. The download rates goes down to 0 B/s and no data keeps coming. When I stop the download and resume again, the download still hangs. But when I redownload it from byte 0 again, everything works fine up to 30 MB when it stops again. Sometimes, after some hours, it just works again without problems. The position in the file when the download stops is variable, but most of the time it is around 30–35 MB. As a download manager I use wget. The same behaviour happens though using curl and other download managers. The error occurs independently of the server I download from. I have also observed this error on other Linux computers in my network. All computers on my network run Gentoo Linux on x86. All internet connections on my network go through a server on my network which runs a transparent Squid proxy on port 80. That server is connected to a router, which is a Speedport W 700V by Deutsche Telekom AG. That router is connected to the internet using ADSL, with 448 kbit/s down speed and 96 kbit/s up speed. I am almost sure that my transparent proxy is not the problem. I turned that off without resolving the issue. I also connected to the router directly via WLAN without resolving the issue. I also tried to download over another port via HTTP. Furthermore, I tried to download the file using IPv6 with a gateway6 tunnel from my computer, which resulted in exactly the same problem. Now the strange thing is that everything works fine using FTP and HTTPS (also with wget on the same computer). Even more strange: when I resume the download that hanged over HTTP using FTP or HTTPS, download a few bytes that way, stop wget and then resume again using HTTP, it loads data again! But after a few MB, it may stop again. Unfortunately, files downloaded that way are always broken (the MD5 sum is not correct), so at some point, there must have been bogus data. I tried searching for HTML error messages in the downloaded file, but grep -i html does not find anything. (I cannot think of a way to search for GZIP-compressed HTML error messages in the file, so I did not try that.) I tried using strace on wget when it failed to resume a download, you can find the entire output on pastebin. The important lines are repeated every second: clock_gettime(CLOCK_MONOTONIC, {326102, 62176435}) = 0 ) = 1 write(2, "78% [++++++++++++++++++++++++++++"..., 19578% [+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ] 110,683,685 --.-K/s ) = 195 select(4, [3], NULL, NULL, {0, 949999}) = 0 (Timeout) I have absolutely no idea what could be the reason of this problem. It seems like whatever causes the issue speaks HTTP. It seems to speak HTTP that intelligently that it even regognises it in an IPv6-over-IPv4 tunnel. But what could that be and why does it only happen sometimes? The other possibility would be that there is a problem on my computer that is the same on other Gentoo Linux computers as well. Has anyone ever had such a problem? What could be the reason and where do I have to continue investigating to find out more about the issue? Update: I have just run into the problem again and tried to resume the download over the router’s WLAN, and this time it worked. Maybe I did something wrong during my last tests with the WLAN. Now maybe my transparent proxy server is in fact the problem. It is a very basic Squid proxy server that does not cache anything. Maybe the fact is interesting that a second Squid proxy runs on the same computer on another port. Update: A download hung again and this time I turned off all firewall settings and stopped all proxy servers. I failed to resume the download from my network server, which is directly connected to the router. So my proxy server definitely is not the cause the problem. I will try to upgrade the firmware of my router now, although I do not have admin access to it. I will see what I can do.

    Read the article

  • Did a recent WinXP update break CD/DVD read speeds? SP2/SP3

    - by quack quixote
    I have two systems with fresh installations of Windows XP Pro SP3 (SP3 slipstreamed into the installer; fully updated after install). One's a refurbished 2.4GHz Pentium4 system; the other is a new 1.6GHz Atom330 build. Both have brand-new dual-layer CD/DVD burners (one's a LiteOn IDE, the other an LG SATA). Both take a really looooong time to read a single-layer DVD in Windows with Cygwin tools. Specifically, 40 minutes or more. I burn backup data to single-layer DVD+/-R and use MD5 hashes for data verification (made with the standard md5sum tool in Unix or Cygwin). The hashes are burned to disc with the data files, and I use this command to verify: $ cd /path/to/disc/mountpoint ; time md5sum -c < md5.txt Here's how long that takes to run on a full single-layer DVD+/-R disc: Old system (WinXP SP2, 1.8GHz Athlon 2500+, last summer): ~10 minutes Old system (Ubuntu 9.04, 1.8GHz Athlon 2500+): ~10 minutes Old system (Debian 5, dual 550MHz P3): ~10 minutes New Pentium4 system (running Ubuntu 9.04): ~5 minutes New Pentium4 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes New Atom330 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes Now the weird stuff: Old system (WinXP SP2, 1.8GHz Athlon 2500+, today): ~25 minutes New Pentium4 system (running WinXP SP3, read from Cygwin): ~40-50 minutes (?!!) New Atom330 system (running WinXP SP3, read from Cygwin): ~40 minutes (can do it in ~30 minutes ...if i have another program spin up the drive first) Since both systems will copy files in 6 minutes using Windows Explorer, I know it's not a hardware problem. Windows just never spins up the drive during the Cygwin read, so it stays super-slow the whole time. Other programs like EAC and DVD Decrypter seem to spin up the disc just fine during their processing. DMA is enabled on both systems. (Can confirm in Windows' Device Manager on the Atom330, not on the P4.) Nero's DriveSpeed tool doesn't seem to have any effect. Copy times are comparable from commandline with Windows' xcopy. Copying with Cygwin's cp looks more like the problem state -- it will spin up the drive for a short time, never reaches full speed, and lets it spin back down again for most of the copy. What I need is to get full read speeds from Cygwin. Is this a known issue with SP3 or some other recent Windows update? Any other ideas? Update: More testing; Windows will spin up the drive when data is copied with Windows tools, but not when read in place or copied with Cygwin tools. It doesn't make sense to me that Windows spins up the drive for copying, but not for other reads. Might be more of a Cygwin problem? Update 2: GUI activity is sluggish during the problem state -- during the Cygwin verifies, there's a slight but noticable delay when dragging windows or icons around on the desktop, switching windows, Alt-Tabbing through open applications, opening new windows, etc. It reminds me of the delay when opening a Windows Explorer window on My Computer just after inserting a DVD. I've tried updating Cygwin (from 1.5.x to 1.7.x), but no change in the problem behavior. I've also noticed this issue occurs on WinXP SP2, but it's not exactly the same -- some spin-up occurs, so the read happens in ~25-30 minutes instead of 40+. The SP2 system used to run the verifies in ~10 minutes, and when it first changed (not sure exactly when, maybe in late November or early December 2009) I thought it was dying hardware. This is why I suspect an official update of breaking this functionality; this has worked for years on that SP2 box.

    Read the article

  • sshd running but no PID file

    - by dunxd
    I'm recently started using monit to monitor the status of sshd on my CentOS 5.4 server. This works fine, but every so often monit reports that sshd is no longer running. This isn't true - I am still able to login to the server via ssh, however I note the following: There is no longer any PID file at /var/run/sshd.pid - after a reboot this file exists. Once it is gone, restarting sshd via service sshd restart does not create the PID file. sudo service sshd status reports openssh-daemon is stopped - again, restarting sshd does not change this, but a reboot does. sudo service sshd stop reports failed, presumably because of the missing PID file. Any idea what is going on? Update sudo netstat -lptun gives the following output relating to port 22 tcp 0 0 :::22 :::* LISTEN 20735/sshd Killing the process with this PID as suggested by @Henry and then starting sshd via service results in service sshd status recognising the process by PID again. Would still like to understand this better. RPM verify suggested by a couple of answerers shows this: sudo rpm -vV openssh openssh-server openssh-clients | grep 'S\.5' S.5....T c /etc/pam.d/sshd S.5....T c /etc/ssh/sshd_config /etc/pam.d/sshd has the following contents: #%PAM-1.0 auth include system-auth account required pam_nologin.so account include system-auth password include system-auth session optional pam_keyinit.so force revoke session include system-auth #session required pam_loginuid.so Should that last line be commented out? Update Here's the output of @YannickGirouard 's script: $ sudo ./sshd_test Searching for the process listening on port 22... Found the following PID: 21330 Command line for PID 21330: /usr/sbin/sshd Listing process(es) relating to PID 21330: UID PID PPID C STIME TTY TIME CMD root 21330 1 0 14:04 ? 00:00:00 /usr/sbin/sshd Listing RPM information about openssh packages: Name : openssh Relocations: (not relocatable) Version : 4.3p2 Vendor: CentOS Release : 72.el5_7.5 Build Date: Tue 30 Aug 2011 12:34:14 AM BST Install Date: Sun 06 Nov 2011 12:50:57 AM GMT Build Host: builder10.centos.org Group : Applications/Internet Source RPM: openssh-4.3p2-72.el5_7.5.src.rpm Size : 745390 License: BSD Signature : DSA/SHA1, Fri 02 Sep 2011 01:13:01 AM BST, Key ID a8a447dce8562897 URL : http://www.openssh.com/portable.html Summary : The OpenSSH implementation of SSH protocol versions 1 and 2 ------------------------------------------------------ Name : openssh-clients Relocations: (not relocatable) Version : 4.3p2 Vendor: CentOS Release : 72.el5_7.5 Build Date: Tue 30 Aug 2011 12:34:14 AM BST Install Date: Sun 06 Nov 2011 12:51:04 AM GMT Build Host: builder10.centos.org Group : Applications/Internet Source RPM: openssh-4.3p2-72.el5_7.5.src.rpm Size : 871132 License: BSD Signature : DSA/SHA1, Fri 02 Sep 2011 01:13:01 AM BST, Key ID a8a447dce8562897 URL : http://www.openssh.com/portable.html Summary : The OpenSSH client applications ------------------------------------------------------ Name : openssh-server Relocations: (not relocatable) Version : 4.3p2 Vendor: CentOS Release : 72.el5_7.5 Build Date: Tue 30 Aug 2011 12:34:14 AM BST Install Date: Sun 06 Nov 2011 12:51:04 AM GMT Build Host: builder10.centos.org Group : System Environment/Daemons Source RPM: openssh-4.3p2-72.el5_7.5.src.rpm Size : 492478 License: BSD Signature : DSA/SHA1, Fri 02 Sep 2011 01:13:01 AM BST, Key ID a8a447dce8562897 URL : http://www.openssh.com/portable.html Summary : The OpenSSH server daemon ------------------------------------------------------ However, I've since got things working by killing the process and starting afresh, as suggested by @Henry below, so perhaps I am no longer seeing the same thing. Will try again if I am seeing the issue again after next reboot. Update - 14 March Monit alerted me that sshd had disappeared, and again I am able to ssh onto the server. So now I can run the script $ sudo ./sshd_test Searching for the process listening on port 22... Found the following PID: 2208 Command line for PID 2208: /usr/sbin/sshd Listing process(es) relating to PID 2208: UID PID PPID C STIME TTY TIME CMD root 2208 1 0 Mar13 ? 00:00:00 /usr/sbin/sshd root 1885 2208 0 21:50 ? 00:00:00 sshd: dunx [priv] Listing RPM information about openssh packages: Name : openssh Relocations: (not relocatable) Version : 4.3p2 Vendor: CentOS Release : 72.el5_7.5 Build Date: Tue 30 Aug 2011 12:34:14 AM BST Install Date: Sun 06 Nov 2011 12:50:57 AM GMT Build Host: builder10.centos.org Group : Applications/Internet Source RPM: openssh-4.3p2-72.el5_7.5.src.rpm Size : 745390 License: BSD Signature : DSA/SHA1, Fri 02 Sep 2011 01:13:01 AM BST, Key ID a8a447dce8562897 URL : http://www.openssh.com/portable.html Summary : The OpenSSH implementation of SSH protocol versions 1 and 2 ------------------------------------------------------ Name : openssh-clients Relocations: (not relocatable) Version : 4.3p2 Vendor: CentOS Release : 72.el5_7.5 Build Date: Tue 30 Aug 2011 12:34:14 AM BST Install Date: Sun 06 Nov 2011 12:51:04 AM GMT Build Host: builder10.centos.org Group : Applications/Internet Source RPM: openssh-4.3p2-72.el5_7.5.src.rpm Size : 871132 License: BSD Signature : DSA/SHA1, Fri 02 Sep 2011 01:13:01 AM BST, Key ID a8a447dce8562897 URL : http://www.openssh.com/portable.html Summary : The OpenSSH client applications ------------------------------------------------------ Name : openssh-server Relocations: (not relocatable) Version : 4.3p2 Vendor: CentOS Release : 72.el5_7.5 Build Date: Tue 30 Aug 2011 12:34:14 AM BST Install Date: Sun 06 Nov 2011 12:51:04 AM GMT Build Host: builder10.centos.org Group : System Environment/Daemons Source RPM: openssh-4.3p2-72.el5_7.5.src.rpm Size : 492478 License: BSD Signature : DSA/SHA1, Fri 02 Sep 2011 01:13:01 AM BST, Key ID a8a447dce8562897 URL : http://www.openssh.com/portable.html Summary : The OpenSSH server daemon ------------------------------------------------------ Again, when I look for /var/run/sshd.pid I don't find it. $ cat /var/run/sshd.pid cat: /var/run/sshd.pid: No such file or directory $ sudo netstat -anp | grep sshd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 2208/sshd $ sudo kill 2208 $ sudo service sshd start Starting sshd: [ OK ] $ cat /var/run/sshd.pid 3794 $ sudo service sshd status openssh-daemon (pid 3794) is running... Is it possible that sshd is restarting and not creating a pidfile for some reason?

    Read the article

  • KVM Virtual guest Paused on Reboot

    - by David Hamilton
    I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

    Read the article

  • OpenVPN and PPTP on XEN VPS

    - by amiv
    I have Debian based system (Ubuntu 11.10) on XEN VPS. I've installed OpenVPN and works great. I need to install PPTP too, so did it and clients can connect, but they have no internet on client side. If I connect to VPN over PPTP I can ping and access to only my VPS by its IP, but ony that. There's no "internet" on client side. It looks it's not DNS problems (I'm using 8.8.8.8) because I can't ping known IPs. I bet the solution is simple, but don't have any idea. Any guess? /etc/pptpd.conf option /etc/ppp/pptpd-options logwtmp localip 46.38.xx.xx remoteip 10.1.0.1-10 /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 8.8.8.8 ms-dns 8.8.4.4 proxyarp nodefaultroute lock nobsdcomp /etc/ppp/ip-up [...] ifconfig ppp0 mtu 1400 /etc/sysctl.conf [...] net.ipv4.ip_forward=1 Command which I run: iptables -t nat -A POSTROUTING -j SNAT --to-source 46.38.xx.xx (IP of my VPS) The client can connect, first one gets IP 10.1.0.1 and DNS from Google. I bet it's iptables problem, am I right? I'm iptables noob and I don't have idea what's wrong. And here's the ifconfig and route command before client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22671 errors:0 dropped:81 overruns:0 frame:0 TX packets:2266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1813358 (1.8 MB) TX bytes:667626 (667.6 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:100 errors:0 dropped:0 overruns:0 frame:0 TX packets:100 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10778 (10.7 KB) TX bytes:10778 (10.7 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And here's the ifconfig and route command after client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.1.0.1 * 255.255.255.255 UH 0 0 0 ppp0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22989 errors:0 dropped:82 overruns:0 frame:0 TX packets:2352 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1841310 (1.8 MB) TX bytes:678456 (678.4 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:12102 (12.1 KB) TX bytes:12102 (12.1 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:46.38.xx.xx P-t-P:10.1.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:66 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:10028 (10.0 KB) TX bytes:660 (660.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And ugly iptables --list output: root@vps3780:~# iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- 10.1.0.0/24 anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.1.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable And ugly iptables -t nat -L output: root@vps3780:~# iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- 10.1.0.0/24 anywhere SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere SNAT all -- anywhere anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere As I said - OpenVPN works very good. 10.8.0.0/24 for OpenVPN (on tun0). PPTP won't work. 10.1.0.0/24 for PPTP (on ppp0). Clients can connect, but they haven't "internet". Any suggestions will be appreciated. Second whole day fighting with no results. EDIT: iptables -t filter -F - it resolved my problem :-)

    Read the article

  • Can't re-mount existing RAID10 on Ubuntu

    - by Zoran
    I saw similar questions, but didn't find what solution to my problem. After power-cut, one of RAID10 (4 disks were) appears to be malfunctioning. I make tha array active one, but can not mount it. Always the same error: mount: you must specify the filesystem type So, here is what I have when type mdadm --detail /dev/md0 /dev/md0: Version : 00.90.03 Creation Time : Tue Sep 1 11:00:40 2009 Raid Level : raid10 Array Size : 1465148928 (1397.27 GiB 1500.31 GB) Used Dev Size : 732574464 (698.64 GiB 750.16 GB) Raid Devices : 4 Total Devices : 3 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Mon Jun 11 09:54:27 2012 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : 1a02e789:c34377a1:2e29483d:f114274d Events : 0.166 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 0 0 1 removed 2 8 48 2 active sync /dev/sdd 3 8 64 3 active sync /dev/sde At the /etc/mdadm/mdadm.conf I have by default, scan all partitions (/proc/partitions) for MD superblocks. alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes automatically tag new arrays as belonging to the local system HOMEHOST <system> instruct the monitoring daemon where to send mail alerts MAILADDR root definitions of existing MD arrays ARRAY /dev/md0 level=raid10 num-devices=4 UUID=1a02e789:c34377a1:2e29483d:f114274d ARRAY /dev/md1 level=raid1 num-devices=2 UUID=9b592be7:c6a2052f:2e29483d:f114274d This file was auto-generated... So, my question is, how can I mount md0 array (md1 has been mounted without problem) in order to preserve existing data? One more thing, fdisk -l command gives the following result: Disk /dev/sdb: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x660a6799 Device Boot Start End Blocks Id System /dev/sdb1 * 1 88217 708603021 83 Linux /dev/sdb2 88218 91201 23968980 5 Extended /dev/sdb5 88218 91201 23968948+ 82 Linux swap / Solaris Disk /dev/sdc: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0008f8ae Device Boot Start End Blocks Id System /dev/sdc1 1 88217 708603021 83 Linux /dev/sdc2 88218 91201 23968980 5 Extended /dev/sdc5 88218 91201 23968948+ 82 Linux swap / Solaris Disk /dev/sdd: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x4be1abdb Device Boot Start End Blocks Id System Disk /dev/sde: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa4d5632e Device Boot Start End Blocks Id System Disk /dev/sdf: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Disk /dev/sdg: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Disk /dev/md1: 750.1 GB, 750156251136 bytes 2 heads, 4 sectors/track, 183143616 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: invalid flag 0x7b6e of partition table 5 will be corrected by w(rite) Disk /dev/md0: 1500.3 GB, 1500312502272 bytes 255 heads, 63 sectors/track, 182402 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x660a6799 Device Boot Start End Blocks Id System /dev/md0p1 * 1 88217 708603021 83 Linux /dev/md0p2 88218 91201 23968980 5 Extended /dev/md0p5 ? 121767 155317 269488144 20 Unknown And one more thing. When using mdadm --examine command, here ise result: mdadm -v --examine --scan /dev/sdb /dev/sdc /dev/sdd /dev/sde /dev/sdf /dev/sd ARRAY /dev/md1 level=raid1 num-devices=2 UUID=9b592be7:c6a2052f:2e29483d:f114274d devices=/dev/sdf ARRAY /dev/md0 level=raid10 num-devices=4 UUID=1a02e789:c34377a1:2e29483d:f114274d devices=/dev/sdb,/dev/sdc,/dev/sdd,/dev/sde md0 has 3 devices which are active. Can someone instruct me how to solve this issue? If it is possible, I would like not to removing faulty HDD. Please advise

    Read the article

  • OpenVPN Server Ethernet Bridging Question

    - by Hooplad
    Hello All, I am having a difficult time properly configuring an ethernet bridge using OpenVPN 2.0.9 install on CentOS 5 ( VPN server ). The goal that I am trying to complete is to connect a VM ( instance running on the same CentOS machine ) acting as a Microsoft Business Contact Manager server. I would then like this "BCM server" to serve Windows XP clients on 192.168.1.0/24 network as well as clients connecting from VPN ( 10.8.0.0/24 ). The setup as it is now was based off a known working configuration. The problem with the working configuration was that it would allow to the client to connect and access everything running on the VPN server ( SVN, Samba, VM Server ) but not any computers on the 192.168.1.0/24 network. I must disclose that the VPN server is behind a router/firewall. Ports are being forwarded correctly ( again, clients were able to connect to the VPN server with no problem. netcat confirms the udp port is open as well ). current ifconfig output br0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 inet addr:192.168.1.169 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:5eff:fe4d:3ac2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:846890 errors:0 dropped:0 overruns:0 frame:0 TX packets:3072351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42686842 (40.7 MiB) TX bytes:4540654180 (4.2 GiB) eth0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:882641 errors:0 dropped:0 overruns:0 frame:0 TX packets:1781383 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:82342803 (78.5 MiB) TX bytes:2614727660 (2.4 GiB) Interrupt:169 eth1 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C3 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:650 errors:0 dropped:0 overruns:0 frame:0 TX packets:1347223 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67403 (65.8 KiB) TX bytes:1959529142 (1.8 GiB) Interrupt:233 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:17452058 errors:0 dropped:0 overruns:0 frame:0 TX packets:17452058 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94020256229 (87.5 GiB) TX bytes:94020256229 (87.5 GiB) tap0 Link encap:Ethernet HWaddr DE:18:C6:D7:01:63 inet6 addr: fe80::dc18:c6ff:fed7:163/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3086 errors:0 dropped:166 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:315099 (307.7 KiB) vmnet1 Link encap:Ethernet HWaddr 00:50:56:C0:00:01 inet addr:192.168.177.1 Bcast:192.168.177.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vmnet8 Link encap:Ethernet HWaddr 00:50:56:C0:00:08 inet addr:192.168.55.1 Bcast:192.168.55.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4226 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) current route table Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.55.0 * 255.255.255.0 U 0 0 0 vmnet8 192.168.177.0 * 255.255.255.0 U 0 0 0 vmnet1 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 current iptables output Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination server_known_working.conf local banshee port 1194 proto udp dev tap0 ca ca.crt cert banshee_server.crt key banshee_server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "route 192.168.1.0 255.255.255.0" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 4 The following is the current CentOS server config file. server_ethernet_bridged.conf ( current ) local 192.168.1.169 port 1194 proto udp dev tap0 ca ca.crt cert server.crt key server.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.1.169 255.255.255.0 192.168.1.200 192.168.1.210 push "route 192.168.1.0 255.255.255.0 192.168.1.1" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 6 The following is one of the client's config file that was used with the known working configuration. client.opvn client dev tap proto udp remote XXX.XXX.XXX 1194 resolv-retry infinite nobind persist-key persist-tun ca client.crt cert client.crt key client.key tls-auth client.key 1 verb 3 I have tried the HOWTO provided by OpenVPN as well as others http://www.thebakershome.net/openvpn%5Ftutorial?page=1 with no success. Any help or suggestions would be appreciated.

    Read the article

  • How to connect FreeBSD Jail to network

    - by jgtumusiime
    So recently I successfully installed and configured a freebsd jail and I would like to install software within my jail but I cannot connect to the network. I'm trying to setup an apache+php+mysql installation within the jail and have the webserver accessible by users. Here is my rc.conf for the jail. ... jail_enable="YES" # Set to NO to disable starting of any jails jail_list="mambo2" # Space separated list of names of jails jail_mambo2_rootdir="/usr/jails/j01" # jail's root directory jail_mambo2_hostname="mambo2.ug" # jail's hostname jail_mambo2_ip="192.168.100.174" # jail's IP address jail_mambo2_devfs_enable="YES" # mount devfs in the jail jail_mambo2_devfs_ruleset="mambo2_ruleset" # devfs ruleset to apply to jail here is my jail ifconfig output mambo2# ifconfig rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 00:c1:28:00:48:db media: Ethernet autoselect (100baseTX <full-duplex>) status: active plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> metric 0 mtu 1500 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 mambo2# It does not show the IP address I configured within /etc/rc.conf. But, when I list the running jails, it shows the right IP address. Here is a list of jails running [root@mambo /usr/home/jtumusiime]# jls JID IP Address Hostname Path 5 192.168.100.174 mambo2.ug /usr/jails/j01 I also created a /etc/resolv.conf for nameservers. This was not in existence so I'm not quite sure if it is necessary? mambo2# cat /etc/resolv.conf nameserver 192.168.100.251 nameserver 8.8.8.8 mambo2# my host has 4 ip addresses, 3 public and one private: 192.168.100.173 I tried creating a jail using ezjail and this does not work out. [root@mambo /usr/src]# ezjail-admin update -p -i Error: Cannot find your copy of the FreeBSD source tree in . Consider using 'ezjail-admin install' to create the base jail from an ftp server. [root@mambo /usr/src]# I have an updated copy of freebsd 7.1 source tree from SVN in /usr/src/ [root@mambo /usr/src]# svn info Path: . URL: http://svn.freebsd.org/base/release/7.1.0 Repository Root: http://svn.freebsd.org/base Repository UUID: ccf9f872-aa2e-dd11-9fc8-001c23d0bc1f Revision: 243371 Node Kind: directory Schedule: normal Last Changed Author: kensmith Last Changed Rev: 186660 Last Changed Date: 2009-01-01 01:57:14 +0300 (Thu, 01 Jan 2009) [root@mambo /usr/src]# and I did #make buildworld while building the first jail i.e mambo2 Here is an excerpt of ouput of ezjail-admin install ... 221 Goodbye. Trying 193.162.146.4... Connected to ftp.freebsd.org. 220 ftp.beastie.tdk.net FTP server (Version 6.00LS) ready. 331 Guest login ok, send your email address as password. 230 Guest login ok, access restrictions apply. Remote system type is UNIX. Using binary mode to transfer files. 200 Type set to I. 550 pub/FreeBSD-Archive/old-releases/i386/7.1-RELEASE/base: No such file or directory. 221 Goodbye. Could not fetch base from ftp.freebsd.org. Maybe your release (7.1-RELEASE) is specified incorrectly or the host ftp.freebsd.org does not provide that release build. Use the -r option to specify an existing release or the -h option to specify an alternative ftp server. Querying your ftp-server... The ftp server you specified (ftp.freebsd.org) seems to provide the following builds: Trying 193.162.146.4... total 10 drwxrwxr-x 13 1006 1006 512 Feb 20 2011 8.2-RELEASE drwxrwxr-x 13 1006 1006 512 Apr 10 2012 8.3-RELEASE lrwxr-xr-x 1 1006 1006 16 Jan 7 2012 9.0-RELEASE -> i386/9.0-RELEASE drwxrwxr-x 7 1006 1006 1024 Feb 19 2012 ISO-IMAGES -rw-rw-r-- 1 1006 1006 637 Nov 23 2005 README.TXT drwxrwxr-x 5 1006 1006 512 Nov 2 02:59 i386 I do not want to upgrade my freebsd installation. I have googled around; but all in vail. Thank you

    Read the article

  • How to add addtional disks to a Windows 2008 KVM based Guest?

    - by taazaa
    I have a Win 2008 KVM based guest VM running on a Ubuntu 10 host. It is a raw image of 22G. I want to add a "data" drive which would show up as "D:\" drive on the guest. I first created a raw image using: qemu-img create -f raw ~/vmdisk2.img 50G Then, tried attaching it using virsh attach-disk. When that did not work, I tried editing the xml file of the VM directly. Both did not seem to work. I would greatly appreciate any help on how to do this and what the best practice is. I want to keep the base image small, so that I can clone it (hopefully) and then attach necessary storage based on the application at hand. Update: The xml of the vm before adding the second drive: <domain type='kvm'> <name>win08e-vm1</name> <uuid>183a4ba0-1c0b-0b04-ad01-aa7c3a4cb390</uuid> <memory>1048576</memory> <currentMemory>1048576</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='localtime'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/win08e-vm1.img'/> <target dev='hda' bus='ide'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/home/taazaa/iso/Win08ER264.iso'/> <target dev='hdc' bus='ide'/> <readonly/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:7f:a7:ae'/> <source bridge='br0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <input type='tablet' bus='usb'/> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' keymap='en-us'/> <video> <model type='vga' vram='9216' heads='1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </memballoon> </devices> </domain> Thanks!

    Read the article

  • Accessing mySQL from two ports: Problems with iptables

    - by marekventur
    Hi! I'm trying to make my mySQL-server (running on Ubuntu) listen on port 3306 and 110, because I would like to access it from a network with very few open ports. So far I've found this answer telling me to do iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 110 -j REDIRECT --to-port 3306 but all I got is: # mysql -h mydomain.com -P 3306 -u username --password=xyz Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 68863 Server version: 5.0.75-0ubuntu10.5 (Ubuntu) Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> exit Bye # mysql -h mydomain.com -P 110 -u username --password=xyz ERROR 2003 (HY000): Can't connect to MySQL server on 'mydomain.com' (111) I'm not an expert with iptables, so I not sure where to look for the problem. I'm googling around for quite some time, but haven't found anything to help me yet. This is what iptable tells me: # iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 32M packets, 1674M bytes) pkts bytes target prot opt in out source destination 0 0 REDIRECT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:110 redir ports 3306 Chain POSTROUTING (policy ACCEPT 855K packets, 55M bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 837K packets, 54M bytes) pkts bytes target prot opt in out source destination # iptables -L -n -v Chain INPUT (policy DROP 7 packets, 340 bytes) pkts bytes target prot opt in out source destination 107K 5390K LOG all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `INPUT INVALID ' 131K 6614K DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x3F/0x00 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x03/0x03 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x06 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x05/0x05 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x11/0x01 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x18/0x08 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x30/0x20 6948K 12G ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 151M 34G ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 32M 1666M ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 1833 106K ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:443 603 29392 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:25 1 60 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:465 24 1180 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:110 1 60 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:995 7919 400K ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:143 1 60 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:993 0 0 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:119 1 60 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:53 7 517 ACCEPT udp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:53 1110 65364 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:21 139K 8313K ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 10176 499K ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:3306 2 80 ACCEPT udp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:123 0 0 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:6060 4 176 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:6667 20987 1179K MY_REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 2159 284K LOG all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `OUTPUT INVALID ' 2630 304K DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 6948K 12G ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 181M 34G ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED 0 0 MY_REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain MY_DROP (7 references) pkts bytes target prot opt in out source destination 0 0 LOG all -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `PORTSCAN DROP ' 0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain MY_REJECT (2 references) pkts bytes target prot opt in out source destination 13806 652K LOG tcp -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `REJECT TCP ' 18171 830K REJECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 reject-with tcp-reset 912 242K LOG udp -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `REJECT UDP ' 912 242K REJECT udp -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable 1904 107K LOG icmp -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `DROP ICMP ' 1904 107K DROP icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 LOG all -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `REJECT OTHER ' 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-proto-unreachable Is there anyone who can give ma a hint where to look for the problem? Thank you!

    Read the article

  • boost::asio::async_read_until problem

    - by user368831
    Hi again, I'm modify the boost asio echo example to use async_read_until to read the input word by word. Even though I am using async_read_until all the data sent seems to be read from the socket. Could someone please advise: #include <cstdlib> #include <iostream> #include <boost/bind.hpp> #include <boost/asio.hpp> using boost::asio::ip::tcp; class session { public: session(boost::asio::io_service& io_service) : socket_(io_service) { } tcp::socket& socket() { return socket_; } void start() { std::cout<<"starting"<<std::endl; boost::asio::async_read_until(socket_, buffer, ' ', boost::bind(&session::handle_read, this, boost::asio::placeholders::error, boost::asio::placeholders::bytes_transferred)); } void handle_read(const boost::system::error_code& error, size_t bytes_transferred) { std::ostringstream ss; ss<<&buffer; std::string s = ss.str(); std::cout<<s<<std::endl; if (!error) { boost::asio::async_write(socket_, boost::asio::buffer(s), boost::bind(&session::handle_write, this, boost::asio::placeholders::error)); } else { delete this; } } void handle_write(const boost::system::error_code& error) { std::cout<<"handling write"<<std::endl; if (!error) { } else { delete this; } } private: tcp::socket socket_; boost::asio::streambuf buffer; }; class server { public: server(boost::asio::io_service& io_service, short port) : io_service_(io_service), acceptor_(io_service, tcp::endpoint(tcp::v4(), port)) { session* new_session = new session(io_service_); acceptor_.async_accept(new_session->socket(), boost::bind(&server::handle_accept, this, new_session, boost::asio::placeholders::error)); } void handle_accept(session* new_session, const boost::system::error_code& error) { if (!error) { new_session->start(); new_session = new session(io_service_); acceptor_.async_accept(new_session->socket(), boost::bind(&server::handle_accept, this, new_session, boost::asio::placeholders::error)); } else { delete new_session; } } private: boost::asio::io_service& io_service_; tcp::acceptor acceptor_; }; int main(int argc, char* argv[]) { try { if (argc != 2) { std::cerr << "Usage: async_tcp_echo_server <port>\n"; return 1; } boost::asio::io_service io_service; using namespace std; // For atoi. server s(io_service, atoi(argv[1])); io_service.run(); } catch (std::exception& e) { std::cerr << "Exception: " << e.what() << "\n"; } return 0; } Thanks!

    Read the article

  • boost::asio::async_read_until problem

    - by user368831
    I'm trying to modify the echo server example from boost asio and I'm running into problem when I try to use boost::asio::async_read_until. Here's the code: #include <cstdlib> #include <iostream> #include <boost/bind.hpp> #include <boost/asio.hpp> using boost::asio::ip::tcp; class session { public: session(boost::asio::io_service& io_service) : socket_(io_service) { } tcp::socket& socket() { return socket_; } void start() { std::cout<<"starting"<<std::endl; boost::asio::async_read_until(socket_, boost::asio::buffer(data_, max_length), ' ', boost::bind(&session::handle_read, this, boost::asio::placeholders::error, boost::asio::placeholders::bytes_transferred)); } void handle_read(const boost::system::error_code& error, size_t bytes_transferred) { std::cout<<"handling read"<<std::endl; if (!error) { boost::asio::async_write(socket_, boost::asio::buffer(data_, bytes_transferred), boost::bind(&session::handle_write, this, boost::asio::placeholders::error)); } else { delete this; } } void handle_write(const boost::system::error_code& error) { if (!error) { /* socket_.async_read_some(boost::asio::buffer(data_, max_length), boost::bind(&session::handle_read, this, boost::asio::placeholders::error, boost::asio::placeholders::bytes_transferred)); */ } else { delete this; } } private: tcp::socket socket_; enum { max_length = 1024 }; char data_[max_length]; }; class server { public: server(boost::asio::io_service& io_service, short port) : io_service_(io_service), acceptor_(io_service, tcp::endpoint(tcp::v4(), port)) { session* new_session = new session(io_service_); acceptor_.async_accept(new_session->socket(), boost::bind(&server::handle_accept, this, new_session, boost::asio::placeholders::error)); } void handle_accept(session* new_session, const boost::system::error_code& error) { if (!error) { new_session->start(); new_session = new session(io_service_); acceptor_.async_accept(new_session->socket(), boost::bind(&server::handle_accept, this, new_session, boost::asio::placeholders::error)); } else { delete new_session; } } private: boost::asio::io_service& io_service_; tcp::acceptor acceptor_; }; int main(int argc, char* argv[]) { try { if (argc != 2) { std::cerr << "Usage: async_tcp_echo_server <port>\n"; return 1; } boost::asio::io_service io_service; using namespace std; // For atoi. server s(io_service, atoi(argv[1])); io_service.run(); } catch (std::exception& e) { std::cerr << "Exception: " << e.what() << "\n"; } return 0; } The problem is when I try to compile I get this weird error: server.cpp: In member function ‘void session::start()’: server.cpp:27: error: no matching function for call to ‘async_read_until(boost::asio::basic_stream_socket &, boost::asio::mutable_buffers_1, char, boost::_bi::bind_t, boost::_bi::list3, boost::arg<1 ()(), boost::arg<2 ()() )’ Can someone please explain what's going on? From what I can tell the arguments to async_read_until are correct. Thanks!

    Read the article

  • Need help with setting up comet code

    - by Saif Bechan
    Does anyone know off a way or maybe think its possible to connect Node.js with Nginx http push module to maintain a persistent connection between client and browser. I am new to comet so just don't understand the publishing etc maybe someone can help me with this. What i have set up so far is the following. I downloaded the jQuery.comet plugin and set up the following basic code: Client JavaScript <script type="text/javascript"> function updateFeed(data) { $('#time').text(data); } function catchAll(data, type) { console.log(data); console.log(type); } $.comet.connect('/broadcast/sub?channel=getIt'); $.comet.bind(updateFeed, 'feed'); $.comet.bind(catchAll); $('#kill-button').click(function() { $.comet.unbind(updateFeed, 'feed'); }); </script> What I can understand from this is that the client will keep on listening to the url followed by /broadcast/sub=getIt. When there is a message it will fire updateFeed. Pretty basic and understandable IMO. Nginx http push module config default_type application/octet-stream; sendfile on; keepalive_timeout 65; push_authorized_channels_only off; server { listen 80; location /broadcast { location = /broadcast/sub { set $push_channel_id $arg_channel; push_subscriber; push_subscriber_concurrency broadcast; push_channel_group broadcast; } location = /broadcast/pub { set $push_channel_id $arg_channel; push_publisher; push_min_message_buffer_length 5; push_max_message_buffer_length 20; push_message_timeout 5s; push_channel_group broadcast; } } } Ok now this tells nginx to listen at port 80 for any calls to /broadcast/sub and it will give back any responses sent to /broadcast/pub. Pretty basic also. This part is not so hard to understand, and is well documented over the internet. Most of the time there is a ruby or a php file behind this that does the broadcasting. My idea is to have node.js broadcasting /broadcast/pub. I think this will let me have persistent streaming data from the server to the client without breaking the connection. I tried the long-polling approach with looping the request but I think this will be more efficient. Or is this not going to work. Node.js file Now to create the Node.js i'm lost. First off all I don't know how to have node.js to work in this way. The setup I used for long polling is as follows: var sys = require('sys'), http = require('http'); http.createServer(function (req, res) { res.writeHead(200, {'Content-Type': 'text/html'}); res.write(new Date()); res.close(); seTimeout('',1000); }).listen(8000); This listens to port 8000 and just writes on the response variable. For long polling my nginx.config looked something like this: server { listen 80; server_name _; location / { proxy_pass http://mydomain.com:8080$request_uri; include /etc/nginx/proxy.conf; } } This just redirected the port 80 to 8000 and this worked fine. Does anyone have an idea on how to have Node.js act in a way Comet understands it. Would be really nice and you will help me out a lot. Recources used An example where this is done with ruby instead of Node.js jQuery.comet Nginx HTTP push module homepage Faye: a Comet client and server for Node.js and Rack To use faye I have to install the comet client, but I want to use the one supplied with Nginx. Thats why I don't just use faye. The one nginx uses is much more optimzed. extra Persistant connections Going evented with Node.js

    Read the article

  • boost::asio::async_write problem

    - by user368831
    Hi, I'm trying to figure out how asynchronous reads and writes work in boost asio by manipulating the echo example. Currently, I have a server that should, when sent a sentence, respond with only the first word. However, the boost::asio::async_write never seems to complete even though the write handler is being called. Can someone please explain what's going on? Here's the code: #include <cstdlib> #include <iostream> #include <boost/bind.hpp> #include <boost/asio.hpp> using boost::asio::ip::tcp; class session { public: session(boost::asio::io_service& io_service) : socket_(io_service) { } tcp::socket& socket() { return socket_; } void start() { std::cout<<"starting"<<std::endl; boost::asio::async_read_until(socket_, buffer, ' ', boost::bind(&session::handle_read, this, boost::asio::placeholders::error, boost::asio::placeholders::bytes_transferred)); } void handle_read(const boost::system::error_code& error, size_t bytes_transferred) { // std::ostringstream ss; // ss<<&buffer; char* c = new char[bytes_transferred]; //std::string s; buffer.sgetn(c,bytes_transferred); std::cout<<"data: "<< c<<" bytes: "<<bytes_transferred<<std::endl; if (!error) { boost::asio::async_write(socket_, boost::asio::buffer(c,bytes_transferred), boost::bind(&session::handle_write, this, boost::asio::placeholders::error)); } else { delete this; } } void handle_write(const boost::system::error_code& error) { std::cout<<"handling write"<<std::endl; if (!error) { } else { delete this; } } private: tcp::socket socket_; boost::asio::streambuf buffer; }; class server { public: server(boost::asio::io_service& io_service, short port) : io_service_(io_service), acceptor_(io_service, tcp::endpoint(tcp::v4(), port)) { session* new_session = new session(io_service_); acceptor_.async_accept(new_session->socket(), boost::bind(&server::handle_accept, this, new_session, boost::asio::placeholders::error)); } void handle_accept(session* new_session, const boost::system::error_code& error) { if (!error) { new_session->start(); new_session = new session(io_service_); acceptor_.async_accept(new_session->socket(), boost::bind(&server::handle_accept, this, new_session, boost::asio::placeholders::error)); } else { delete new_session; } } private: boost::asio::io_service& io_service_; tcp::acceptor acceptor_; }; int main(int argc, char* argv[]) { try { if (argc != 2) { std::cerr << "Usage: async_tcp_echo_server <port>\n"; return 1; } boost::asio::io_service io_service; using namespace std; // For atoi. server s(io_service, atoi(argv[1])); io_service.run(); } catch (std::exception& e) { std::cerr << "Exception: " << e.what() << "\n"; } return 0; } Thanks!

    Read the article

  • Hudson + Jboss AS 7.1 + Maven 3 Project Build Error

    - by Zehra Gül Çabuk
    I've wanted to prepare an environment that I'm able to build my project and run my tests on a integration server. So I've installed an Jboss application server 7.1 and deployed hudson.war to it. Then I've created a project to trigger "mvn clean install" and when I built it I've got following exception. [INFO] Using bundled Maven 3 installation [INFO] Checking Maven 3 installation environment [workspace] $ /disk7/hudson_home/maven/slavebundle/bundled-maven/bin/mvn --help [INFO] Checking Maven 3 installation version [INFO] Detected Maven 3 installation version: 3.0.3 [workspace] $ /disk7/hudson_home/maven/slavebundle/bundled-maven/bin/mvn clean install -V -B -Dmaven.ext.class.path=/disk7/hudson_home/maven/slavebundle/resources:/disk7/hudson_home/maven/slavebundle/lib/maven3-eventspy-3.0.jar:/disk7/jboss-as-7.1.0.Final/standalone/tmp/vfs/deploymentdf2a6dfa59ee3407/hudson-remoting-2.2.0.jar-407215e5de02980f/contents -Dhudson.eventspy.port=37183 -f pom.xml [DEBUG] Waiting for connection on port: 37183 Apache Maven 3.0.3 (r1075438; 2011-02-28 19:31:09+0200) Maven home: /disk7/hudson_home/maven/slavebundle/bundled-maven Java version: 1.7.0_04, vendor: Oracle Corporation Java home: /usr/lib/jvm/jdk1.7.0_04/jre Default locale: en_US, platform encoding: UTF-8 OS name: "linux", version: "3.2.0-24-generic", arch: "amd64", family: "unix" [ERROR] o.h.m.e.DelegatingEventSpy - Init failed java.lang.NoClassDefFoundError: hudson/remoting/Channel at org.hudsonci.maven.eventspy.common.RemotingClient.open(RemotingClient.java:103) ~[maven3-eventspy-runtime.jar:na] at org.hudsonci.maven.eventspy_30.RemotingEventSpy.openChannel(RemotingEventSpy.java:86) ~[maven3-eventspy-3.0.jar:na] at org.hudsonci.maven.eventspy_30.RemotingEventSpy.init(RemotingEventSpy.java:114) ~[maven3-eventspy-3.0.jar:na] at org.hudsonci.maven.eventspy_30.DelegatingEventSpy.init(DelegatingEventSpy.java:128) ~[maven3-eventspy-3.0.jar:na] at org.apache.maven.eventspy.internal.EventSpyDispatcher.init(EventSpyDispatcher.java:84) [maven-core-3.0.3.jar:3.0.3] at org.apache.maven.cli.MavenCli.container(MavenCli.java:403) [maven-embedder-3.0.3.jar:3.0.3] at org.apache.maven.cli.MavenCli.doMain(MavenCli.java:191) [maven-embedder-3.0.3.jar:3.0.3] at org.apache.maven.cli.MavenCli.main(MavenCli.java:141) [maven-embedder-3.0.3.jar:3.0.3] at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) ~[na:1.7.0_04] at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) ~[na:1.7.0_04] at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) ~[na:1.7.0_04] at java.lang.reflect.Method.invoke(Method.java:601) ~[na:1.7.0_04] at org.codehaus.plexus.classworlds.launcher.Launcher.launchEnhanced(Launcher.java:290) [plexus-classworlds-2.4.jar:na] at org.codehaus.plexus.classworlds.launcher.Launcher.launch(Launcher.java:230) [plexus-classworlds-2.4.jar:na] at org.codehaus.plexus.classworlds.launcher.Launcher.mainWithExitCode(Launcher.java:409) [plexus-classworlds-2.4.jar:na] at org.codehaus.plexus.classworlds.launcher.Launcher.main(Launcher.java:352) [plexus-classworlds-2.4.jar:na] Caused by: java.lang.ClassNotFoundException: hudson.remoting.Channel at org.codehaus.plexus.classworlds.strategy.SelfFirstStrategy.loadClass(SelfFirstStrategy.java:50) ~[plexus-classworlds-2.4.jar:na] at org.codehaus.plexus.classworlds.realm.ClassRealm.loadClass(ClassRealm.java:244) ~[plexus-classworlds-2.4.jar:na] at org.codehaus.plexus.classworlds.realm.ClassRealm.loadClass(ClassRealm.java:230) ~[plexus-classworlds-2.4.jar:na] ... 16 common frames omitted [ERROR] ABORTED [ERROR] Failed to initialize [ERROR] Caused by: hudson/remoting/Channel [ERROR] Caused by: hudson.remoting.Channel [ERROR] Failure: java.net.SocketException: Connection reset FATAL: Connection reset java.net.SocketException: Connection reset at java.net.SocketInputStream.read(SocketInputStream.java:189) at java.net.SocketInputStream.read(SocketInputStream.java:121) at java.io.FilterInputStream.read(FilterInputStream.java:133) at java.io.BufferedInputStream.fill(BufferedInputStream.java:235) at java.io.BufferedInputStream.read(BufferedInputStream.java:254) at hudson.remoting.Channel.<init>(Channel.java:385) at hudson.remoting.Channel.<init>(Channel.java:347) at hudson.remoting.Channel.<init>(Channel.java:320) at hudson.remoting.Channel.<init>(Channel.java:315) at hudson.slaves.Channels$1.<init>(Channels.java:71) at hudson.slaves.Channels.forProcess(Channels.java:71) at org.hudsonci.maven.plugin.builder.internal.PerformBuild.doExecute(PerformBuild.java:174) at org.hudsonci.utils.tasks.PerformOperation.execute(PerformOperation.java:58) at org.hudsonci.maven.plugin.builder.MavenBuilder.perform(MavenBuilder.java:169) at hudson.tasks.BuildStepMonitor$1.perform(BuildStepMonitor.java:19) at hudson.model.AbstractBuild$AbstractRunner.perform(AbstractBuild.java:630) at hudson.model.Build$RunnerImpl.build(Build.java:175) at hudson.model.Build$RunnerImpl.doRun(Build.java:137) at hudson.model.AbstractBuild$AbstractRunner.run(AbstractBuild.java:429) at hudson.model.Run.run(Run.java:1366) at hudson.model.FreeStyleBuild.run(FreeStyleBuild.java:46) at hudson.model.ResourceController.execute(ResourceController.java:88) at hudson.model.Executor.run(Executor.java:145) I want to point out the command which is tried to execute by hudson : /disk7/hudson_home/maven/slavebundle/bundled-maven/bin/mvn clean install -V -B -Dmaven.ext.class.path=/disk7/hudson_home/maven/slavebundle/resources:/disk7/hudson_home/maven/slavebundle/lib/maven3-eventspy-3.0.jar:/disk7/jboss-as-7.1.0.Final/standalone/tmp/vfs/deploymentdf2a6dfa59ee3407/hudson-remoting-2.2.0.jar-407215e5de02980f/contents -Dhudson.eventspy.port=37183 -f pom.xml It tries to find "hudson-remoting-2.2.0.jar" to put it to build path but it searches it at the wrong place because when I look where the hudson-remoting jar I found it at /disk7/jboss-as-7.1.0.Final/standalone/tmp/vfs/deploymentdf2a6dfa59ee3407/hudson-remoting-2.2.0.jar-407215e5de02980f/hudson-remoting-2.2.0.jar for this build(not in contents). So how can I configure the hudson to force it looking at the right place for jars? Is there anyone has an idea? Thanks in advance.

    Read the article

  • wso2 ESB: server configuration CRITICAL

    - by nuvio
    My Scenario: I have server_1 (192.168.10.1) with wso2-ESB and server_2 (192.168.10.2) with Glassfish-v3 + web services. Problem: I am trying to create a proxy in ESB using the java Web Services, but the created proxy does not respond properly. The log says: Unable to sendViaPost for http or https does not change the result. I think I should configure the axis2.xml but I am having trouble, and don't know what to do. What is the configuration for my scenario? Please help me! EDIT: To be clear, I can directly consume the WebService in the Glassfish server, it works normal, both port and url are accessible. Only when I create a "Pass through Proxy" in the ESB, it does not work. I don't think is matter of Proxy configuration...I never had problems while deployed locally, problems started once I have uploaded the ESB to a remote server. I really would need someone to point me what is the correct procedure when installing the ESB on a remote host: configuration of axis2.xml and carbon.xml, ports, transport receivers etc... P.S. I had a look at the official (wso2 esb and carbon) guides with no luck, but I am missing something... Endpoint of Java Web Service: http://192.168.10.2:8080/HelloWorld/Hello?wsdl ESB Proxy Enpoint: http://192.168.10.1:8280/services/HelloProxy The following is my axis2.xml configuration, please check it: <transportReceiver name="http" class="org.apache.synapse.transport.nhttp.HttpCoreNIOListener"> <parameter name="port" locked="false">8280</parameter> <parameter name="non-blocking" locked="false">true</parameter> <parameter name="bind-address" locked="false">192.168.10.1</parameter> <parameter name="WSDLEPRPrefix" locked="false">https//192.168.10.1:8280</parameter> <parameter name="httpGetProcessor" locked="false">org.wso2.carbon.transport.nhttp.api.NHttpGetProcessor</parameter> <!--<parameter name="priorityConfigFile" locked="false">location of priority configuration file</parameter>--> </transportReceiver> <!-- the non blocking https transport based on HttpCore + SSL-NIO extensions --> <transportReceiver name="https" class="org.apache.synapse.transport.nhttp.HttpCoreNIOSSLListener"> <parameter name="port" locked="false">8243</parameter> <parameter name="non-blocking" locked="false">true</parameter> <parameter name="bind-address" locked="false">192.168.10.1</parameter> <parameter name="WSDLEPRPrefix" locked="false">https://192.168.10.1:8243</parameter> <!--<parameter name="priorityConfigFile" locked="false">location of priority configuration file</parameter>--> <parameter name="httpGetProcessor" locked="false">org.wso2.carbon.transport.nhttp.api.NHttpGetProcessor</parameter> <parameter name="keystore" locked="false"> <KeyStore> <Location>repository/resources/security/wso2carbon.jks</Location> <Type>JKS</Type> <Password>wso2carbon</Password> <KeyPassword>wso2carbon</KeyPassword> </KeyStore> </parameter> <parameter name="truststore" locked="false"> <TrustStore> <Location>repository/resources/security/client-truststore.jks</Location> <Type>JKS</Type> <Password>wso2carbon</Password> </TrustStore> </parameter> <!--<parameter name="SSLVerifyClient">require</parameter> supports optional|require or defaults to none --> </transportReceiver>

    Read the article

  • 'normal' SVC versus 'Silverlight' SVC (WCF)

    - by Michel
    Hi, i'm trying to call a WCF service from my Silverlight 3 app. But... when trying to create a 'silverlight enabled wcf service' in my web project, my VS2008 crashes during creating the item (i think while editing the web.config). So i thought: let's create a 'normal' wcf service, and manually edit it to be a 'silverlight enabled webservice'. So i wondered what the differences are, and second: why is there a difference between a service called from a silverlight app and a non-silverlight app? This is what i have now for the binding (i have a service without an Interface contract, just a direct class exposed, to begin with): <system.serviceModel> <behaviors> <serviceBehaviors> <behavior name="RadControlsSilverlightApp1.Web.GetNewDataBehavior"> <serviceMetadata httpGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="false" /> </behavior> </serviceBehaviors> </behaviors> <bindings> <customBinding> <binding name="customBinding0"> <binaryMessageEncoding /> <httpTransport /> </binding> </customBinding> </bindings> <serviceHostingEnvironment aspNetCompatibilityEnabled="true" /> <services> <service behaviorConfiguration="RadControlsSilverlightApp1.Web.GetNewDataBehavior" name="RadControlsSilverlightApp1.Web.GetNewData"> <endpoint address="" binding="customBinding" bindingConfiguration="customBinding0" contract="RadControlsSilverlightApp1.Web.GetNewData" /> <endpoint address="mex" binding="mexHttpBinding" contract="IMetadataExchange" /> </service> </services> </system.serviceModel> This one doesn't work because when i add a reference to it from the silverlight app i get these messages: Warning 2 Custom tool warning: Cannot import wsdl:portType Detail: An exception was thrown while running a WSDL import extension: System.ServiceModel.Description.DataContractSerializerMessageContractImporter Error: Exception has been thrown by the target of an invocation. XPath to Error Source: //wsdl:definitions[@targetNamespace='']/wsdl:portType[@name='GetNewData'] C:\Silverlight\RadControlsSilverlightApp1\RadControlsSilverlightApp1\Service References\ServiceReference1\Reference.svcmap 1 1 RadControlsSilverlightApp1 Warning 3 Custom tool warning: Cannot import wsdl:binding Detail: There was an error importing a wsdl:portType that the wsdl:binding is dependent on. XPath to wsdl:portType: //wsdl:definitions[@targetNamespace='']/wsdl:portType[@name='GetNewData'] XPath to Error Source: //wsdl:definitions[@targetNamespace='http://tempuri.org/']/wsdl:binding[@name='CustomBinding_GetNewData'] C:\Silverlight\RadControlsSilverlightApp1\RadControlsSilverlightApp1\Service References\ServiceReference1\Reference.svcmap 1 1 RadControlsSilverlightApp1 Warning 4 Custom tool warning: Cannot import wsdl:port Detail: There was an error importing a wsdl:binding that the wsdl:port is dependent on. XPath to wsdl:binding: //wsdl:definitions[@targetNamespace='http://tempuri.org/']/wsdl:binding[@name='CustomBinding_GetNewData'] XPath to Error Source: //wsdl:definitions[@targetNamespace='http://tempuri.org/']/wsdl:service[@name='GetNewData']/wsdl:port[@name='CustomBinding_GetNewData'] C:\Silverlight\RadControlsSilverlightApp1\RadControlsSilverlightApp1\Service References\ServiceReference1\Reference.svcmap 1 1 RadControlsSilverlightApp1 Warning 5 Custom tool warning: No endpoints compatible with Silverlight 3 were found. The generated client class will not be usable unless endpoint information is provided via the constructor. C:\Silverlight\RadControlsSilverlightApp1\RadControlsSilverlightApp1\Service References\ServiceReference1\Reference.svcmap 1 1 RadControlsSilverlightApp1 (ps., the service can be started in the browser, i get this: svcutil.exe http://localhost:9599/GetNewData.svc?wsdl )

    Read the article

  • Does boost::asio makes excessive small heap allocations or am I wrong?

    - by Poni
    #include <cstdlib> #include <iostream> #include <boost/bind.hpp> #include <boost/asio.hpp> using boost::asio::ip::tcp; class session { public: session(boost::asio::io_service& io_service) : socket_(io_service) { } tcp::socket& socket() { return socket_; } void start() { socket_.async_read_some(boost::asio::buffer(data_, max_length - 1), boost::bind(&session::handle_read, this, boost::asio::placeholders::error, boost::asio::placeholders::bytes_transferred)); } void handle_read(const boost::system::error_code& error, size_t bytes_transferred) { if (!error) { data_[bytes_transferred] = '\0'; if(NULL != strstr(data_, "quit")) { this->socket().shutdown(boost::asio::ip::tcp::socket::shutdown_both); this->socket().close(); // how to make this dispatch "handle_read()" with a "disconnected" flag? } else { boost::asio::async_write(socket_, boost::asio::buffer(data_, bytes_transferred), boost::bind(&session::handle_write, this, boost::asio::placeholders::error)); socket_.async_read_some(boost::asio::buffer(data_, max_length - 1), boost::bind(&session::handle_read, this, boost::asio::placeholders::error, boost::asio::placeholders::bytes_transferred)); } } else { delete this; } } void handle_write(const boost::system::error_code& error) { if (!error) { // } else { delete this; } } private: tcp::socket socket_; enum { max_length = 1024 }; char data_[max_length]; }; class server { public: server(boost::asio::io_service& io_service, short port) : io_service_(io_service), acceptor_(io_service, tcp::endpoint(tcp::v4(), port)) { session* new_session = new session(io_service_); acceptor_.async_accept(new_session->socket(), boost::bind(&server::handle_accept, this, new_session, boost::asio::placeholders::error)); } void handle_accept(session* new_session, const boost::system::error_code& error) { if (!error) { new_session->start(); new_session = new session(io_service_); acceptor_.async_accept(new_session->socket(), boost::bind(&server::handle_accept, this, new_session, boost::asio::placeholders::error)); } else { delete new_session; } } private: boost::asio::io_service& io_service_; tcp::acceptor acceptor_; }; int main(int argc, char* argv[]) { try { if (argc != 2) { std::cerr << "Usage: async_tcp_echo_server <port>\n"; return 1; } boost::asio::io_service io_service; using namespace std; // For atoi. server s(io_service, atoi(argv[1])); io_service.run(); } catch (std::exception& e) { std::cerr << "Exception: " << e.what() << "\n"; } return 0; } While experimenting with boost::asio I've noticed that within the calls to async_write()/async_read_some() there is a usage of the C++ "new" keyword. Also, when stressing this echo server with a client (1 connection) that sends for example 100,000 times some data, the memory usage of this program is getting higher and higher. What's going on? Will it allocate memory for every call? Or am I wrong? Asking because it doesn't seem right that a server app will allocate, anything. Can I handle it, say with a memory pool? Another side-question: See the "this-socket().close();" ? I want it, as the comment right to it says, to dispatch that same function one last time, with a disconnection error. Need that to do some clean-up. How do I do that? Thank you all gurus (:

    Read the article

  • Trying to run Selenium tests using Hudson - "Error: no display specified"

    - by tputkonen
    I'm trying to get Selenium tests to work when they are executed by Hudson, but I have not been successful so far. Hudson is running on Ubuntu, and Selenium is unable to open display. Command I use for launching the build is: mvn clean selenium:xvfb install error log: [INFO] [selenium:xvfb {execution: default-cli}] [INFO] Starting Xvfb... [INFO] Using display: :20 [INFO] Using Xauthority file: /tmp/Xvfb4467650583214148352.Xauthority Deleting: /tmp/Xvfb4467650583214148352.Xauthority xauth: creating new authority file /tmp/Xvfb4467650583214148352.Xauthority Created dir: /var/lib/hudson/jobs/Selenium/workspace/selenium/target/selenium Launching Xvfb Waiting for Xvfb... [INFO] Redirecting output to: /var/lib/hudson/jobs/Selenium/workspace/selenium/target/selenium/xvfb.log Xvfb started ... [INFO] [selenium:start-server {execution: start}] Launching Selenium Server Waiting for Selenium Server... [INFO] Including display properties from: /var/lib/hudson/jobs/Selenium/workspace/selenium/target/selenium/display.properties [INFO] Redirecting output to: /var/lib/hudson/jobs/Selenium/workspace/selenium/target/selenium/server.log [INFO] User extensions: /var/lib/hudson/jobs/Selenium/workspace/selenium/target/selenium/user-extensions.js Selenium Server started [INFO] [selenium:selenese {execution: run-selenium}] [INFO] Results will go to: /var/lib/hudson/jobs/Selenium/workspace/selenium/target/results-firefox-suite.html ... <~30 seconds pause> ... Error: no display specified ... pom.xml: <groupId>org.codehaus.mojo</groupId> <artifactId>selenium-maven-plugin</artifactId> <version>1.0.1</version> <executions> <execution> <id>start</id> <phase>pre-integration-test</phase> <goals> <goal>start-server</goal> </goals> <configuration> <logOutput>true</logOutput> <background>true</background> <port>5123</port> </configuration> </execution> <execution> <id>run-selenium</id> <phase>integration-test</phase> <goals> <goal>selenese</goal> </goals> </execution> <execution> <id>stop</id> <phase>post-integration-test</phase> <goals> <goal>stop-server</goal> </goals> </execution> </executions> <configuration> <browser>*firefox</browser> <suite>src/test/selenium/suite.html</suite> <startURL>http://localhost:${env.port}</startURL> </configuration> I've also tried to get it working by adding execution for xvfb, but also it failed.

    Read the article

< Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >