Search Results

Search found 8766 results on 351 pages for 'integrated authentication'.

Page 267/351 | < Previous Page | 263 264 265 266 267 268 269 270 271 272 273 274  | Next Page >

  • Creating static NAT blocks outbound traffic Cisco ASA

    - by natediggs
    Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

    Read the article

  • OpenSwan IPsec connection drops after 30 seconds

    - by drcore
    I'm trying to connection from my Linux Mint 16 box to a CloudStack server. Building up the connection works (pings work across the tunnel). However 30 seconds later the IPsec tunnel gets terminated out of the blue. What could cause this consistent behaviour and how to fix it? The tunnel is setup using OpenSwan (U2.6.38/K(no kernel code presently loaded)) with the L2TP IPsec VPN manager from Werner Jaeger 1.0.9. The client is behind a NAT'ed router and the server is on public IP (CloudStack 4.2) Running ipsec verify complains about IPsec support in kernel. Not sure if this is a problem as the connection is being build up: Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K(no kernel code presently loaded) Checking for IPsec support in kernel [FAILED] SAref kernel support [N/A] Checking that pluto is running [FAILED] whack: Pluto is not running (no "/var/run/pluto/pluto.ctl") Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] Tunnel config: version 2.0 # conforms to second version of ipsec.conf specification config setup # plutodebug="parsing emitting control private" plutodebug=none strictcrlpolicy=no nat_traversal=yes interfaces=%defaultroute oe=off # which IPsec stack to use. netkey,klips,mast,auto or none protostack=netkey conn %default keyingtries=3 pfs=no rekey=yes type=transport left=%defaultroute leftprotoport=17/1701 rightprotoport=17/1701 conn Tunnel1 authby=secret right=37.48.75.97 rightid="" auto=add Log file of VPN connection build up: aug. 23 17:12:54.708 ipsec_setup: Starting Openswan IPsec U2.6.38/K3.11.0-12-generic... aug. 23 17:12:55.155 ipsec_setup: multiple ip addresses, using 192.168.178.32 on eth0 aug. 23 17:12:55.165 ipsec__plutorun: Starting Pluto subsystem... aug. 23 17:12:55.174 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d aug. 23 17:12:55.177 recvref[30]: Protocol not available aug. 23 17:12:55.177 xl2tpd[14339]: This binary does not support kernel L2TP. aug. 23 17:12:55.178 Starting xl2tpd: xl2tpd. aug. 23 17:12:55.178 xl2tpd[14345]: xl2tpd version xl2tpd-1.3.1 started on desktopmint PID:14345 aug. 23 17:12:55.178 xl2tpd[14345]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. aug. 23 17:12:55.179 xl2tpd[14345]: Forked by Scott Balmos and David Stipp, (C) 2001 aug. 23 17:12:55.179 xl2tpd[14345]: Inherited by Jeff McAdams, (C) 2002 aug. 23 17:12:55.179 xl2tpd[14345]: Forked again by Xelerance (www.xelerance.com) (C) 2006 aug. 23 17:12:55.180 xl2tpd[14345]: Listening on IP address 0.0.0.0, port 1701 aug. 23 17:12:55.214 ipsec__plutorun: 002 added connection description "Tunnel1" aug. 23 17:13:15.532 104 "Tunnel1" #1: STATE_MAIN_I1: initiate aug. 23 17:13:15.532 003 "Tunnel1" #1: ignoring unknown Vendor ID payload [4f45755c645c6a795c5c6170] aug. 23 17:13:15.532 003 "Tunnel1" #1: received Vendor ID payload [Dead Peer Detection] aug. 23 17:13:15.533 003 "Tunnel1" #1: received Vendor ID payload [RFC 3947] method set to=115 aug. 23 17:13:15.533 106 "Tunnel1" #1: STATE_MAIN_I2: sent MI2, expecting MR2 aug. 23 17:13:15.534 003 "Tunnel1" #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): i am NATed aug. 23 17:13:15.534 108 "Tunnel1" #1: STATE_MAIN_I3: sent MI3, expecting MR3 aug. 23 17:13:15.534 010 "Tunnel1" #1: STATE_MAIN_I3: retransmission; will wait 20s for response aug. 23 17:13:15.545 003 "Tunnel1" #1: received Vendor ID payload [CAN-IKEv2] aug. 23 17:13:15.547 004 "Tunnel1" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_128 prf=oakley_sha group=modp2048} aug. 23 17:13:15.547 117 "Tunnel1" #2: STATE_QUICK_I1: initiate aug. 23 17:13:15.547 010 "Tunnel1" #2: STATE_QUICK_I1: retransmission; will wait 20s for response aug. 23 17:13:15.548 004 "Tunnel1" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x0ecef28b <0x3e1fbe3b xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} aug. 23 17:13:16.549 xl2tpd[14345]: Connecting to host <VPN gateway>, port 1701 aug. 23 17:13:18.576 xl2tpd[14345]: Connection established to <VPN gateway>, 1701. Local: 21163, Remote: 12074 (ref=0/0). aug. 23 17:13:18.576 xl2tpd[14345]: Calling on tunnel 21163 aug. 23 17:13:18.577 xl2tpd[14345]: check_control: Received out of order control packet on tunnel 12074 (got 0, expected 1) aug. 23 17:13:18.577 xl2tpd[14345]: handle_packet: bad control packet! aug. 23 17:13:18.577 xl2tpd[14345]: check_control: Received out of order control packet on tunnel 12074 (got 0, expected 1) aug. 23 17:13:18.577 xl2tpd[14345]: handle_packet: bad control packet! aug. 23 17:13:18.599 xl2tpd[14345]: Call established with <VPN gateway>, Local: 39035, Remote: 57266, Serial: 1 (ref=0/0) aug. 23 17:13:18.605 xl2tpd[14345]: start_pppd: I'm running: aug. 23 17:13:18.605 xl2tpd[14345]: "/usr/sbin/pppd" aug. 23 17:13:18.606 xl2tpd[14345]: "passive" aug. 23 17:13:18.606 xl2tpd[14345]: "nodetach" aug. 23 17:13:18.606 xl2tpd[14345]: ":" aug. 23 17:13:18.606 xl2tpd[14345]: "file" aug. 23 17:13:18.606 xl2tpd[14345]: "/etc/ppp/Tunnel1.options.xl2tpd" aug. 23 17:13:18.606 xl2tpd[14345]: "ipparam" aug. 23 17:13:18.607 xl2tpd[14345]: "<VPN gateway>" aug. 23 17:13:18.607 xl2tpd[14345]: "/dev/pts/4" aug. 23 17:13:18.607 pppd[14438]: Plugin passprompt.so loaded. aug. 23 17:13:18.607 pppd[14438]: pppd 2.4.5 started by root, uid 0 aug. 23 17:13:18.608 pppd[14438]: Using interface ppp0 aug. 23 17:13:18.608 pppd[14438]: Connect: ppp0 <--> /dev/pts/4 aug. 23 17:13:21.650 pppd[14438]: CHAP authentication succeeded: Access granted aug. 23 17:13:21.651 pppd[14438]: CHAP authentication succeeded aug. 23 17:13:21.692 pppd[14438]: local IP address 10.1.2.2 aug. 23 17:13:21.693 pppd[14438]: remote IP address 10.1.2.1 aug. 23 17:13:21.693 pppd[14438]: primary DNS address 10.1.2.1 aug. 23 17:13:21.694 pppd[14438]: secondary DNS address 10.1.2.1 aug. 23 17:13:46.528 Stopping xl2tpd: xl2tpd. aug. 23 17:13:46.528 xl2tpd[14345]: death_handler: Fatal signal 15 received aug. 23 17:13:46.529 pppd[14438]: Modem hangup aug. 23 17:13:46.529 pppd[14438]: Connect time 0.5 minutes. aug. 23 17:13:46.529 pppd[14438]: Sent 1866 bytes, received 1241 bytes. aug. 23 17:13:46.529 pppd[14438]: Connection terminated. aug. 23 17:13:46.562 ipsec_setup: Stopping Openswan IPsec... aug. 23 17:13:46.576 pppd[14438]: Exit.

    Read the article

  • Why my VPN doesn't work anymore?

    - by xx77aBs
    I have openvpn server running on debian lenny. There is only one client - and it is running Windows 7 64-bit. This has worked for few months without any problems. And now, let's say for the last 7 days, it doesn't work at all. I connect successfully from client to the server, but I can't access anything through VPN. I have set it up so that all internet traffic is routed through VPN, and now when I connect with the client, the client can't do anything on the net (open any webpage, ping google, anything ...). Can you help me to figure out what's wrong ? I don't know where to start. I've also tried to connect to another openvpn server (I've installed and configured openvpn on another server, and when I try to connect to it result is the same). So I think there's something wrong with client ... Here is my connection log: Wed Apr 04 21:35:59 2012 OpenVPN 2.3-alpha1 Win32-MSVC++ [SSL (OpenSSL)] [LZO2] [PF_INET6] [IPv6 payload 20110522-1 (2.2.0)] built on Feb 21 2012 Enter Management Password: Wed Apr 04 21:35:59 2012 MANAGEMENT: TCP Socket listening on [AF_INET]127.0.0.10:25340 Wed Apr 04 21:35:59 2012 Need hold release from management interface, waiting... Wed Apr 04 21:36:00 2012 MANAGEMENT: Client connected from [AF_INET]127.0.0.10:25340 Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'state on' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'log all on' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'hold off' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'hold release' Wed Apr 04 21:36:00 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Wed Apr 04 21:36:00 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Apr 04 21:36:00 2012 Socket Buffers: R=[8192->8192] S=[8192->8192] Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,RESOLVE,,, Wed Apr 04 21:36:00 2012 UDPv4 link local: [undef] Wed Apr 04 21:36:00 2012 UDPv4 link remote: [AF_INET]11.22.33.44:1234 Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,WAIT,,, Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,AUTH,,, Wed Apr 04 21:36:00 2012 TLS: Initial packet from [AF_INET]11.22.33.44:1234, sid=ee329574 f15e9e04 Wed Apr 04 21:36:00 2012 VERIFY OK: depth=1, C=US, ST=CA, L=SanFrancisco, O=Fort-Funston, CN=Fort-Funston CA, [email protected] Wed Apr 04 21:36:00 2012 VERIFY OK: depth=0, C=US, ST=CA, L=SanFrancisco, O=Fort-Funston, CN=server_key, [email protected] Wed Apr 04 21:36:01 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Apr 04 21:36:01 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Apr 04 21:36:01 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Apr 04 21:36:01 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Apr 04 21:36:01 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Apr 04 21:36:01 2012 [server_key] Peer Connection Initiated with [AF_INET]11.22.33.44:1234 Wed Apr 04 21:36:02 2012 MANAGEMENT: >STATE:1333568162,GET_CONFIG,,, Wed Apr 04 21:36:03 2012 SENT CONTROL [server_key]: 'PUSH_REQUEST' (status=1) Wed Apr 04 21:36:03 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,route 172.16.100.1,topology net30,ping 10,ping-restart 120,ifconfig 172.16.100.6 172.16.100.5' Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: timers and/or timeouts modified Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: --ifconfig/up options modified Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: route options modified Wed Apr 04 21:36:03 2012 ROUTE_GATEWAY 192.168.1.1/255.255.255.0 I=15 HWADDR=00:1f:1f:3f:61:55 Wed Apr 04 21:36:03 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Wed Apr 04 21:36:03 2012 MANAGEMENT: >STATE:1333568163,ASSIGN_IP,,172.16.100.6, Wed Apr 04 21:36:03 2012 open_tun, tt->ipv6=0 Wed Apr 04 21:36:03 2012 TAP-WIN32 device [VPN] opened: \\.\Global\{E28FD52B-F6C3-4094-A36A-30CB02FAC7E8}.tap Wed Apr 04 21:36:03 2012 TAP-Win32 Driver Version 9.9 Wed Apr 04 21:36:03 2012 Notified TAP-Win32 driver to set a DHCP IP/netmask of 172.16.100.6/255.255.255.252 on interface {E28FD52B-F6C3-4094-A36A-30CB02FAC7E8} [DHCP-serv: 172.16.100.5, lease-time: 31536000] Wed Apr 04 21:36:03 2012 Successful ARP Flush on interface [31] {E28FD52B-F6C3-4094-A36A-30CB02FAC7E8} Wed Apr 04 21:36:08 2012 TEST ROUTES: 2/2 succeeded len=1 ret=1 a=0 u/d=up Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 11.22.33.44 MASK 255.255.255.255 192.168.1.1 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=25 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 0.0.0.0 MASK 128.0.0.0 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 128.0.0.0 MASK 128.0.0.0 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 MANAGEMENT: >STATE:1333568168,ADD_ROUTES,,, Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 172.16.100.1 MASK 255.255.255.255 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 Initialization Sequence Completed Wed Apr 04 21:36:08 2012 MANAGEMENT: >STATE:1333568168,CONNECTED,SUCCESS,172.16.100.6,11.22.33.44 Client's route table after connection with OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.41 281 0.0.0.0 128.0.0.0 172.16.100.1 172.16.100.6 31 94.23.53.45 255.255.255.255 192.168.1.1 192.168.1.41 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 172.16.100.1 172.16.100.6 31 172.16.100.4 255.255.255.252 On-link 172.16.100.6 286 172.16.100.6 255.255.255.255 On-link 172.16.100.6 286 172.16.100.7 255.255.255.255 On-link 172.16.100.6 286 192.168.1.0 255.255.255.0 On-link 192.168.1.41 281 192.168.1.41 255.255.255.255 On-link 192.168.1.41 281 192.168.1.255 255.255.255.255 On-link 192.168.1.41 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.41 281 224.0.0.0 240.0.0.0 On-link 172.16.100.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.41 281 255.255.255.255 255.255.255.255 On-link 172.16.100.6 286 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.1.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 13 58 ::/0 On-link 1 306 ::1/128 On-link 13 58 2001::/32 On-link 13 306 2001:0:5ef5:79fd:3cc3:6b9:ac7c:14db/128 On-link 15 281 fe80::/64 On-link 31 286 fe80::/64 On-link 13 306 fe80::/64 On-link 13 306 fe80::3cc3:6b9:ac7c:14db/128 On-link 31 286 fe80::7d72:9515:7213:35e3/128 On-link 15 281 fe80::9cec:ce3f:89de:a123/128 On-link 1 306 ff00::/8 On-link 13 306 ff00::/8 On-link 15 281 ff00::/8 On-link 31 286 ff00::/8 On-link =========================================================================== Persistent Routes: None

    Read the article

  • Sendmail to local domain ignoring MX records (part 2)

    - by FractalizeR
    Hello. I have the exact problem, like in this post: http://serverfault.com/questions/25068/sendmail-to-local-domain-ignoring-mx-records I am also using email provider like GMail For Your Domain (which stores your mail and manages it). I am sending mail from my server directly, but receiving mail is done via Yandex (email provider). Since the server hosts forum, I prefer to send mail directly from it because using another mail provider can slow things. Also, when I send 300.000 emails to my subscribers, email provider will surely block me thinking I send spam. My DNS zone now is: ; ; GSMFORUM.RU ; $TTL 1H gsmforum.ru. SOA ns1.hc.ru. support.hc.ru. ( 2009122268 ; Serial 1H ; Refresh 30M ; Retry 1W ; Expire 1H ) ; Minimum gsmforum.ru. NS ns1.hc.ru. gsmforum.ru. NS ns2.hc.ru. @ A 79.174.68.223 *.gsmforum.ru. CNAME @ ns1 A 79.174.68.223 ns2 A 79.174.68.224 @ MX 10 mx.yandex.ru. mail CNAME domain.mail.yandex.net. yamail-xxxxxxxxx CNAME mail.yandex.ru. Server hostname is server.gsmforum.ru. May be this is the cause? Can someone explain the reason of the matter (the rules that make sendmail consider domain to be local)? Can I easily change *.gsmforum.ru. CNAME @ into *.gsmforum.ru. A 79.174.68.224 to solve this problem? [root@server ~]# cat /etc/mail/local-host-names localhost localhost.localdomain This server hosts gsmforum.ru so I cannot put it into another domain like David Mackintosh suggests. Putting domain in mailertable doesn't solve the problem also. sendmail -bt still shows, that address is local. DontProbeInterfaces is also set to true at sendmail config. M4 file follows: divert(-1)dnl dnl # dnl # This is the sendmail macro config file for m4. If you make changes to dnl # /etc/mail/sendmail.mc, you will need to regenerate the dnl # /etc/mail/sendmail.cf file by confirming that the sendmail-cf package is dnl # installed and then performing a dnl # dnl # make -C /etc/mail dnl # include(`/usr/share/sendmail-cf/m4/cf.m4')dnl VERSIONID(`setup for linux')dnl OSTYPE(`linux')dnl dnl # dnl # Do not advertize sendmail version. dnl # dnl define(`confSMTP_LOGIN_MSG', `$j Sendmail; $b')dnl dnl # dnl # default logging level is 9, you might want to set it higher to dnl # debug the configuration dnl # dnl define(`confLOG_LEVEL', `9')dnl dnl # dnl # Uncomment and edit the following line if your outgoing mail needs to dnl # be sent out through an external mail server: dnl # dnl define(`SMART_HOST', `smtp.your.provider')dnl dnl # define(`confDEF_USER_ID', ``8:12'')dnl dnl define(`confAUTO_REBUILD')dnl define(`confTO_CONNECT', `1m')dnl define(`confTRY_NULL_MX_LIST', `True')dnl define(`confDONT_PROBE_INTERFACES',`True') define(`PROCMAIL_MAILER_PATH', `/usr/bin/procmail')dnl define(`ALIAS_FILE', `/etc/aliases')dnl define(`STATUS_FILE', `/var/log/mail/statistics')dnl define(`UUCP_MAILER_MAX', `2000000')dnl define(`confUSERDB_SPEC', `/etc/mail/userdb.db')dnl define(`confPRIVACY_FLAGS', `authwarnings,novrfy,noexpn,restrictqrun')dnl define(`confAUTH_OPTIONS', `A')dnl dnl # dnl # The following allows relaying if the user authenticates, and disallows dnl # plaintext authentication (PLAIN/LOGIN) on non-TLS links dnl # dnl define(`confAUTH_OPTIONS', `A p')dnl dnl # dnl # PLAIN is the preferred plaintext authentication method and used by dnl # Mozilla Mail and Evolution, though Outlook Express and other MUAs do dnl # use LOGIN. Other mechanisms should be used if the connection is not dnl # guaranteed secure. dnl # Please remember that saslauthd needs to be running for AUTH. dnl # dnl TRUST_AUTH_MECH(`EXTERNAL DIGEST-MD5 CRAM-MD5 LOGIN PLAIN')dnl dnl define(`confAUTH_MECHANISMS', `EXTERNAL GSSAPI DIGEST-MD5 CRAM-MD5 LOGIN PLAIN')dnl dnl # dnl # Rudimentary information on creating certificates for sendmail TLS: dnl # cd /usr/share/ssl/certs; make sendmail.pem dnl # Complete usage: dnl # make -C /usr/share/ssl/certs usage dnl # dnl define(`confCACERT_PATH', `/etc/pki/tls/certs')dnl dnl define(`confCACERT', `/etc/pki/tls/certs/ca-bundle.crt')dnl dnl define(`confSERVER_CERT', `/etc/pki/tls/certs/sendmail.pem')dnl dnl define(`confSERVER_KEY', `/etc/pki/tls/certs/sendmail.pem')dnl dnl # dnl # This allows sendmail to use a keyfile that is shared with OpenLDAP's dnl # slapd, which requires the file to be readble by group ldap dnl # dnl define(`confDONT_BLAME_SENDMAIL', `groupreadablekeyfile')dnl dnl # dnl define(`confTO_QUEUEWARN', `4h')dnl dnl define(`confTO_QUEUERETURN', `5d')dnl dnl define(`confQUEUE_LA', `12')dnl dnl define(`confREFUSE_LA', `18')dnl define(`confTO_IDENT', `0')dnl dnl FEATURE(delay_checks)dnl FEATURE(`no_default_msa', `dnl')dnl FEATURE(`smrsh', `/usr/sbin/smrsh')dnl FEATURE(`mailertable', `hash -o /etc/mail/mailertable.db')dnl FEATURE(`virtusertable', `hash -o /etc/mail/virtusertable.db')dnl FEATURE(redirect)dnl FEATURE(always_add_domain)dnl FEATURE(use_cw_file)dnl FEATURE(use_ct_file)dnl dnl # dnl # The following limits the number of processes sendmail can fork to accept dnl # incoming messages or process its message queues to 20.) sendmail refuses dnl # to accept connections once it has reached its quota of child processes. dnl # dnl define(`confMAX_DAEMON_CHILDREN', `20')dnl dnl # dnl # Limits the number of new connections per second. This caps the overhead dnl # incurred due to forking new sendmail processes. May be useful against dnl # DoS attacks or barrages of spam. (As mentioned below, a per-IP address dnl # limit would be useful but is not available as an option at this writing.) dnl # dnl define(`confCONNECTION_RATE_THROTTLE', `3')dnl dnl # dnl # The -t option will retry delivery if e.g. the user runs over his quota. dnl # FEATURE(local_procmail, `', `procmail -t -Y -a $h -d $u')dnl FEATURE(`access_db', `hash -T<TMPF> -o /etc/mail/access.db')dnl FEATURE(`blacklist_recipients')dnl EXPOSED_USER(`root')dnl dnl # dnl # For using Cyrus-IMAPd as POP3/IMAP server through LMTP delivery uncomment dnl # the following 2 definitions and activate below in the MAILER section the dnl # cyrusv2 mailer. dnl # dnl define(`confLOCAL_MAILER', `cyrusv2')dnl dnl define(`CYRUSV2_MAILER_ARGS', `FILE /var/lib/imap/socket/lmtp')dnl dnl # dnl # The following causes sendmail to only listen on the IPv4 loopback address dnl # 127.0.0.1 and not on any other network devices. Remove the loopback dnl # address restriction to accept email from the internet or intranet. dnl # DAEMON_OPTIONS(`Name=MTA,Port=smtp') dnl # dnl # The following causes sendmail to additionally listen to port 587 for dnl # mail from MUAs that authenticate. Roaming users who can't reach their dnl # preferred sendmail daemon due to port 25 being blocked or redirected find dnl # this useful. dnl # dnl DAEMON_OPTIONS(`Port=submission, Name=MSA, M=Ea')dnl dnl # dnl # The following causes sendmail to additionally listen to port 465, but dnl # starting immediately in TLS mode upon connecting. Port 25 or 587 followed dnl # by STARTTLS is preferred, but roaming clients using Outlook Express can't dnl # do STARTTLS on ports other than 25. Mozilla Mail can ONLY use STARTTLS dnl # and doesn't support the deprecated smtps; Evolution <1.1.1 uses smtps dnl # when SSL is enabled-- STARTTLS support is available in version 1.1.1. dnl # dnl # For this to work your OpenSSL certificates must be configured. dnl # dnl DAEMON_OPTIONS(`Port=smtps, Name=TLSMTA, M=s')dnl dnl # dnl # The following causes sendmail to additionally listen on the IPv6 loopback dnl # device. Remove the loopback address restriction listen to the network. dnl # dnl DAEMON_OPTIONS(`port=smtp,Addr=::1, Name=MTA-v6, Family=inet6')dnl dnl # dnl # enable both ipv6 and ipv4 in sendmail: dnl # dnl DAEMON_OPTIONS(`Name=MTA-v4, Family=inet, Name=MTA-v6, Family=inet6') dnl # dnl # We strongly recommend not accepting unresolvable domains if you want to dnl # protect yourself from spam. However, the laptop and users on computers dnl # that do not have 24x7 DNS do need this. dnl # FEATURE(`accept_unresolvable_domains')dnl dnl # dnl FEATURE(`relay_based_on_MX')dnl dnl # dnl # Also accept email sent to "localhost.localdomain" as local email. dnl # LOCAL_DOMAIN(`localhost.localdomain')dnl dnl # dnl # The following example makes mail from this host and any additional dnl # specified domains appear to be sent from mydomain.com dnl # dnl MASQUERADE_AS(`mydomain.com')dnl dnl # dnl # masquerade not just the headers, but the envelope as well dnl # dnl FEATURE(masquerade_envelope)dnl dnl # dnl # masquerade not just @mydomainalias.com, but @*.mydomainalias.com as well dnl # dnl FEATURE(masquerade_entire_domain)dnl dnl # dnl MASQUERADE_DOMAIN(localhost)dnl dnl MASQUERADE_DOMAIN(localhost.localdomain)dnl dnl MASQUERADE_DOMAIN(mydomainalias.com)dnl dnl MASQUERADE_DOMAIN(mydomain.lan)dnl MAILER(smtp)dnl MAILER(procmail)dnl dnl MAILER(cyrusv2)dnl FEATURE(`dnsbl',`zen.spamhaus.org',`Rejected - your IP is blacklisted by http://www.spamhaus.org')

    Read the article

  • ProFTPd server on Ubuntu getting access denied message when successfully authenticated?

    - by exxoid
    I have a Ubuntu box with a ProFTPD 1.3.4a Server, when I try to log in via my FTP Client I cannot do anything as it does not allow me to list directories; I have tried logging in as root and as a regular user and tried accessing different paths within the FTP Server. The error I get in my FTP Client is: Status: Retrieving directory listing... Command: CDUP Response: 250 CDUP command successful Command: PWD Response: 257 "/var" is the current directory Command: PASV Response: 227 Entering Passive Mode (172,16,4,22,237,205). Command: MLSD Response: 550 Access is denied. Error: Failed to retrieve directory listing Any idea? Here is the config of my proftpd: # # /etc/proftpd/proftpd.conf -- This is a basic ProFTPD configuration file. # To really apply changes, reload proftpd after modifications, if # it runs in daemon mode. It is not required in inetd/xinetd mode. # # Includes DSO modules Include /etc/proftpd/modules.conf # Set off to disable IPv6 support which is annoying on IPv4 only boxes. UseIPv6 off # If set on you can experience a longer connection delay in many cases. IdentLookups off ServerName "Drupal Intranet" ServerType standalone ServerIdent on "FTP Server ready" DeferWelcome on # Set the user and group that the server runs as User nobody Group nogroup MultilineRFC2228 on DefaultServer on ShowSymlinks on TimeoutNoTransfer 600 TimeoutStalled 600 TimeoutIdle 1200 DisplayLogin welcome.msg DisplayChdir .message true ListOptions "-l" DenyFilter \*.*/ # Use this to jail all users in their homes # DefaultRoot ~ # Users require a valid shell listed in /etc/shells to login. # Use this directive to release that constrain. # RequireValidShell off # Port 21 is the standard FTP port. Port 21 # In some cases you have to specify passive ports range to by-pass # firewall limitations. Ephemeral ports can be used for that, but # feel free to use a more narrow range. # PassivePorts 49152 65534 # If your host was NATted, this option is useful in order to # allow passive tranfers to work. You have to use your public # address and opening the passive ports used on your firewall as well. # MasqueradeAddress 1.2.3.4 # This is useful for masquerading address with dynamic IPs: # refresh any configured MasqueradeAddress directives every 8 hours <IfModule mod_dynmasq.c> # DynMasqRefresh 28800 </IfModule> # To prevent DoS attacks, set the maximum number of child processes # to 30. If you need to allow more than 30 concurrent connections # at once, simply increase this value. Note that this ONLY works # in standalone mode, in inetd mode you should use an inetd server # that allows you to limit maximum number of processes per service # (such as xinetd) MaxInstances 30 # Set the user and group that the server normally runs at. # Umask 022 is a good standard umask to prevent new files and dirs # (second parm) from being group and world writable. Umask 022 022 # Normally, we want files to be overwriteable. AllowOverwrite on # Uncomment this if you are using NIS or LDAP via NSS to retrieve passwords: # PersistentPasswd off # This is required to use both PAM-based authentication and local passwords AuthPAMConfig proftpd AuthOrder mod_auth_pam.c* mod_auth_unix.c # Be warned: use of this directive impacts CPU average load! # Uncomment this if you like to see progress and transfer rate with ftpwho # in downloads. That is not needed for uploads rates. # UseSendFile off TransferLog /var/log/proftpd/xferlog SystemLog /var/log/proftpd/proftpd.log # Logging onto /var/log/lastlog is enabled but set to off by default #UseLastlog on # In order to keep log file dates consistent after chroot, use timezone info # from /etc/localtime. If this is not set, and proftpd is configured to # chroot (e.g. DefaultRoot or <Anonymous>), it will use the non-daylight # savings timezone regardless of whether DST is in effect. #SetEnv TZ :/etc/localtime <IfModule mod_quotatab.c> QuotaEngine off </IfModule> <IfModule mod_ratio.c> Ratios off </IfModule> # Delay engine reduces impact of the so-called Timing Attack described in # http://www.securityfocus.com/bid/11430/discuss # It is on by default. <IfModule mod_delay.c> DelayEngine on </IfModule> <IfModule mod_ctrls.c> ControlsEngine off ControlsMaxClients 2 ControlsLog /var/log/proftpd/controls.log ControlsInterval 5 ControlsSocket /var/run/proftpd/proftpd.sock </IfModule> <IfModule mod_ctrls_admin.c> AdminControlsEngine off </IfModule> # # Alternative authentication frameworks # #Include /etc/proftpd/ldap.conf #Include /etc/proftpd/sql.conf # # This is used for FTPS connections # #Include /etc/proftpd/tls.conf # # Useful to keep VirtualHost/VirtualRoot directives separated # #Include /etc/proftpd/virtuals.con # A basic anonymous configuration, no upload directories. # <Anonymous ~ftp> # User ftp # Group nogroup # # We want clients to be able to login with "anonymous" as well as "ftp" # UserAlias anonymous ftp # # Cosmetic changes, all files belongs to ftp user # DirFakeUser on ftp # DirFakeGroup on ftp # # RequireValidShell off # # # Limit the maximum number of anonymous logins # MaxClients 10 # # # We want 'welcome.msg' displayed at login, and '.message' displayed # # in each newly chdired directory. # DisplayLogin welcome.msg # DisplayChdir .message # # # Limit WRITE everywhere in the anonymous chroot # <Directory *> # <Limit WRITE> # DenyAll # </Limit> # </Directory> # # # Uncomment this if you're brave. # # <Directory incoming> # # # Umask 022 is a good standard umask to prevent new files and dirs # # # (second parm) from being group and world writable. # # Umask 022 022 # # <Limit READ WRITE> # # DenyAll # # </Limit> # # <Limit STOR> # # AllowAll # # </Limit> # # </Directory> # # </Anonymous> # Include other custom configuration files Include /etc/proftpd/conf.d/ UseReverseDNS off <Global> RootLogin on UseFtpUsers on ServerIdent on DefaultChdir /var/www DeleteAbortedStores on LoginPasswordPrompt on AccessGrantMsg "You have been authenticated successfully." </Global> Any idea what could be wrong? Thanks for your help!

    Read the article

  • rsync over ssh is not working anymore, while ssh itself is working fine (Write failed: broken pipe)

    - by brazorf
    This issue started happening after i changed router. This is the scenario: Windows7 Host Ubuntu 10.04 Guest (VirtualBox) Ubuntu 10.04 remote server What i used to do is run a very basic rsync command: rsync -avz --delete /local/path/ username@host:/path/to/remote/directory This worked perfect until i did change adsl provider, and i changed router aswell: now, this happens: rsync on Ubuntu Guest is not working anymore (to any random server), if using this new router rsync on Ubuntu Guest is WORKING, if i switch back to old router i tried a new virtual box ubuntu install, and the command is WORKING with both the routers So, the not-working-combo is oldUbuntu + newRouter. To get things worst, i can state that (on the not-working ubuntu) i ping the remote host plain ssh connection to the remote host is working fine (i can auth, connect, and do stuff on the remote host) scp is NOT working (this is just a further thing i tried) This is the console output of the execution, with ssh verbose set to vvvv: root@client:~# rsync -ae 'ssh -vvvv' /root/test-rsync/ {username}@{hostname}:/home/{username}/test/ OpenSSH_5.3p1 Debian-3ubuntu7, OpenSSL 0.9.8k 25 Mar 2009 debug1: Reading configuration data /root/.ssh/config debug1: Applying options for {hostname} debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to {hostname} [{ip.add.re.ss}] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug3: Not a RSA1 key file /root/.ssh/{private_key}. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /root/.ssh/{private_key} type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debian-3ubuntu7 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu7 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3p1 Debian-3ubuntu7 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug3: Wrote 792 bytes for a total of 831 debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: [email protected],zlib,none debug2: kex_parse_kexinit: [email protected],zlib,none debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 [email protected] debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 [email protected] debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug3: Wrote 24 bytes for a total of 855 debug2: dh_gen_key: priv key bits set: 125/256 debug2: bits set: 525/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: Wrote 144 bytes for a total of 999 debug3: check_host_in_hostfile: filename /root/.ssh/known_hosts debug3: check_host_in_hostfile: match line 4 debug3: check_host_in_hostfile: filename /root/.ssh/known_hosts debug3: check_host_in_hostfile: match line 5 debug1: Host '{hostname}' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:4 debug2: bits set: 512/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /root/.ssh/{private_key} (0x7f3ad0e7f9b0) debug3: Wrote 80 bytes for a total of 1143 debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /root/.ssh/{private_key} debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1511 debug1: Server accepts key: pkalg ssh-rsa blen 277 debug2: input_userauth_pk_ok: fp 1b:65:36:92:59:b3:12:3e:8c:c6:03:28:d4:81:09:dc debug3: sign_and_send_pubkey debug1: read PEM private key done: type RSA debug3: Wrote 656 bytes for a total of 2167 debug1: Enabling compression at level 6. debug1: Authentication succeeded (publickey). debug2: fd 4 setting O_NONBLOCK debug3: fd 5 is O_NONBLOCK debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug3: Wrote 112 bytes for a total of 2279 debug2: callback start debug2: client_session2_setup: id 0 debug1: Sending environment. debug3: Ignored env TERM debug3: Ignored env SHELL debug3: Ignored env SSH_CLIENT debug3: Ignored env SSH_TTY debug1: Sending env LC_ALL = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env MAIL debug3: Ignored env PATH debug3: Ignored env PWD debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env SHLVL debug3: Ignored env HOME debug3: Ignored env LANGUAGE debug3: Ignored env LOGNAME debug3: Ignored env SSH_CONNECTION debug3: Ignored env LESSOPEN debug3: Ignored env LESSCLOSE debug3: Ignored env _ debug1: Sending command: rsync --server -logDtpre.iLsf . /home/{username}/test/ debug2: channel 0: request exec confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug3: Wrote 208 bytes for a total of 2487 At this point everything freeze for lots of minutes, ending in Write failed: Broken pipe rsync: connection unexpectedly closed (0 bytes received so far) [sender] rsync error: unexplained error (code 255) at io.c(601) [sender=3.0.7] Any suggestion? Thank You F. Edit 2012/09/13: i am changing title and issue definition, since i made some TINY step ahead and i think i can give more detailed clues.

    Read the article

  • Integrating JavaScript Unit Tests with Visual Studio

    - by Stephen Walther
    Modern ASP.NET web applications take full advantage of client-side JavaScript to provide better interactivity and responsiveness. If you are building an ASP.NET application in the right way, you quickly end up with lots and lots of JavaScript code. When writing server code, you should be writing unit tests. One big advantage of unit tests is that they provide you with a safety net that enable you to safely modify your existing code – for example, fix bugs, add new features, and make performance enhancements -- without breaking your existing code. Every time you modify your code, you can execute your unit tests to verify that you have not broken anything. For the same reason that you should write unit tests for your server code, you should write unit tests for your client code. JavaScript is just as susceptible to bugs as C#. There is no shortage of unit testing frameworks for JavaScript. Each of the major JavaScript libraries has its own unit testing framework. For example, jQuery has QUnit, Prototype has UnitTestJS, YUI has YUI Test, and Dojo has Dojo Objective Harness (DOH). The challenge is integrating a JavaScript unit testing framework with Visual Studio. Visual Studio and Visual Studio ALM provide fantastic support for server-side unit tests. You can easily view the results of running your unit tests in the Visual Studio Test Results window. You can set up a check-in policy which requires that all unit tests pass before your source code can be committed to the source code repository. In addition, you can set up Team Build to execute your unit tests automatically. Unfortunately, Visual Studio does not provide “out-of-the-box” support for JavaScript unit tests. MS Test, the unit testing framework included in Visual Studio, does not support JavaScript unit tests. As soon as you leave the server world, you are left on your own. The goal of this blog entry is to describe one approach to integrating JavaScript unit tests with MS Test so that you can execute your JavaScript unit tests side-by-side with your C# unit tests. The goal is to enable you to execute JavaScript unit tests in exactly the same way as server-side unit tests. You can download the source code described by this project by scrolling to the end of this blog entry. Rejected Approach: Browser Launchers One popular approach to executing JavaScript unit tests is to use a browser as a test-driver. When you use a browser as a test-driver, you open up a browser window to execute and view the results of executing your JavaScript unit tests. For example, QUnit – the unit testing framework for jQuery – takes this approach. The following HTML page illustrates how you can use QUnit to create a unit test for a function named addNumbers(). <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd"> <html> <head> <title>Using QUnit</title> <link rel="stylesheet" href="http://github.com/jquery/qunit/raw/master/qunit/qunit.css" type="text/css" /> </head> <body> <h1 id="qunit-header">QUnit example</h1> <h2 id="qunit-banner"></h2> <div id="qunit-testrunner-toolbar"></div> <h2 id="qunit-userAgent"></h2> <ol id="qunit-tests"></ol> <div id="qunit-fixture">test markup, will be hidden</div> <script type="text/javascript" src="http://code.jquery.com/jquery-latest.js"></script> <script type="text/javascript" src="http://github.com/jquery/qunit/raw/master/qunit/qunit.js"></script> <script type="text/javascript"> // The function to test function addNumbers(a, b) { return a+b; } // The unit test test("Test of addNumbers", function () { equals(4, addNumbers(1,3), "1+3 should be 4"); }); </script> </body> </html> This test verifies that calling addNumbers(1,3) returns the expected value 4. When you open this page in a browser, you can see that this test does, in fact, pass. The idea is that you can quickly refresh this QUnit HTML JavaScript test driver page in your browser whenever you modify your JavaScript code. In other words, you can keep a browser window open and keep refreshing it over and over while you are developing your application. That way, you can know very quickly whenever you have broken your JavaScript code. While easy to setup, there are several big disadvantages to this approach to executing JavaScript unit tests: You must view your JavaScript unit test results in a different location than your server unit test results. The JavaScript unit test results appear in the browser and the server unit test results appear in the Visual Studio Test Results window. Because all of your unit test results don’t appear in a single location, you are more likely to introduce bugs into your code without noticing it. Because your unit tests are not integrated with Visual Studio – in particular, MS Test -- you cannot easily include your JavaScript unit tests when setting up check-in policies or when performing automated builds with Team Build. A more sophisticated approach to using a browser as a test-driver is to automate the web browser. Instead of launching the browser and loading the test code yourself, you use a framework to automate this process. There are several different testing frameworks that support this approach: · Selenium – Selenium is a very powerful framework for automating browser tests. You can create your tests by recording a Firefox session or by writing the test driver code in server code such as C#. You can learn more about Selenium at http://seleniumhq.org/. LTAF – The ASP.NET team uses the Lightweight Test Automation Framework to test JavaScript code in the ASP.NET framework. You can learn more about LTAF by visiting the project home at CodePlex: http://aspnet.codeplex.com/releases/view/35501 jsTestDriver – This framework uses Java to automate the browser. jsTestDriver creates a server which can be used to automate multiple browsers simultaneously. This project is located at http://code.google.com/p/js-test-driver/ TestSwam – This framework, created by John Resig, uses PHP to automate the browser. Like jsTestDriver, the framework creates a test server. You can open multiple browsers that are automated by the test server. Learn more about TestSwarm by visiting the following address: https://github.com/jeresig/testswarm/wiki Yeti – This is the framework introduced by Yahoo for automating browser tests. Yeti uses server-side JavaScript and depends on Node.js. Learn more about Yeti at http://www.yuiblog.com/blog/2010/08/25/introducing-yeti-the-yui-easy-testing-interface/ All of these frameworks are great for integration tests – however, they are not the best frameworks to use for unit tests. In one way or another, all of these frameworks depend on executing tests within the context of a “living and breathing” browser. If you create an ASP.NET Unit Test then Visual Studio will launch a web server before executing the unit test. Why is launching a web server so bad? It is not the worst thing in the world. However, it does introduce dependencies that prevent your code from being tested in isolation. One of the defining features of a unit test -- versus an integration test – is that a unit test tests code in isolation. Another problem with launching a web server when performing unit tests is that launching a web server can be slow. If you cannot execute your unit tests quickly, you are less likely to execute your unit tests each and every time you make a code change. You are much more likely to fall into the pit of failure. Launching a browser when performing a JavaScript unit test has all of the same disadvantages as launching a web server when performing an ASP.NET unit test. Instead of testing a unit of JavaScript code in isolation, you are testing JavaScript code within the context of a particular browser. Using the frameworks listed above for integration tests makes perfect sense. However, I want to consider a different approach for creating unit tests for JavaScript code. Using Server-Side JavaScript for JavaScript Unit Tests A completely different approach to executing JavaScript unit tests is to perform the tests outside of any browser. If you really want to test JavaScript then you should test JavaScript and leave the browser out of the testing process. There are several ways that you can execute JavaScript on the server outside the context of any browser: Rhino – Rhino is an implementation of JavaScript written in Java. The Rhino project is maintained by the Mozilla project. Learn more about Rhino at http://www.mozilla.org/rhino/ V8 – V8 is the open-source Google JavaScript engine written in C++. This is the JavaScript engine used by the Chrome web browser. You can download V8 and embed it in your project by visiting http://code.google.com/p/v8/ JScript – JScript is the JavaScript Script Engine used by Internet Explorer (up to but not including Internet Explorer 9), Windows Script Host, and Active Server Pages. Internet Explorer is still the most popular web browser. Therefore, I decided to focus on using the JScript Script Engine to execute JavaScript unit tests. Using the Microsoft Script Control There are two basic ways that you can pass JavaScript to the JScript Script Engine and execute the code: use the Microsoft Windows Script Interfaces or use the Microsoft Script Control. The difficult and proper way to execute JavaScript using the JScript Script Engine is to use the Microsoft Windows Script Interfaces. You can learn more about the Script Interfaces by visiting http://msdn.microsoft.com/en-us/library/t9d4xf28(VS.85).aspx The main disadvantage of using the Script Interfaces is that they are difficult to use from .NET. There is a great series of articles on using the Script Interfaces from C# located at http://www.drdobbs.com/184406028. I picked the easier alternative and used the Microsoft Script Control. The Microsoft Script Control is an ActiveX control that provides a higher level abstraction over the Window Script Interfaces. You can download the Microsoft Script Control from here: http://www.microsoft.com/downloads/en/details.aspx?FamilyID=d7e31492-2595-49e6-8c02-1426fec693ac After you download the Microsoft Script Control, you need to add a reference to it to your project. Select the Visual Studio menu option Project, Add Reference to open the Add Reference dialog. Select the COM tab and add the Microsoft Script Control 1.0. Using the Script Control is easy. You call the Script Control AddCode() method to add JavaScript code to the Script Engine. Next, you call the Script Control Run() method to run a particular JavaScript function. The reference documentation for the Microsoft Script Control is located at the MSDN website: http://msdn.microsoft.com/en-us/library/aa227633%28v=vs.60%29.aspx Creating the JavaScript Code to Test To keep things simple, let’s imagine that you want to test the following JavaScript function named addNumbers() which simply adds two numbers together: MvcApplication1\Scripts\Math.js function addNumbers(a, b) { return 5; } Notice that the addNumbers() method always returns the value 5. Right-now, it will not pass a good unit test. Create this file and save it in your project with the name Math.js in your MVC project’s Scripts folder (Save the file in your actual MVC application and not your MVC test application). Creating the JavaScript Test Helper Class To make it easier to use the Microsoft Script Control in unit tests, we can create a helper class. This class contains two methods: LoadFile() – Loads a JavaScript file. Use this method to load the JavaScript file being tested or the JavaScript file containing the unit tests. ExecuteTest() – Executes the JavaScript code. Use this method to execute a JavaScript unit test. Here’s the code for the JavaScriptTestHelper class: JavaScriptTestHelper.cs   using System; using System.IO; using Microsoft.VisualStudio.TestTools.UnitTesting; using MSScriptControl; namespace MvcApplication1.Tests { public class JavaScriptTestHelper : IDisposable { private ScriptControl _sc; private TestContext _context; /// <summary> /// You need to use this helper with Unit Tests and not /// Basic Unit Tests because you need a Test Context /// </summary> /// <param name="testContext">Unit Test Test Context</param> public JavaScriptTestHelper(TestContext testContext) { if (testContext == null) { throw new ArgumentNullException("TestContext"); } _context = testContext; _sc = new ScriptControl(); _sc.Language = "JScript"; _sc.AllowUI = false; } /// <summary> /// Load the contents of a JavaScript file into the /// Script Engine. /// </summary> /// <param name="path">Path to JavaScript file</param> public void LoadFile(string path) { var fileContents = File.ReadAllText(path); _sc.AddCode(fileContents); } /// <summary> /// Pass the path of the test that you want to execute. /// </summary> /// <param name="testMethodName">JavaScript function name</param> public void ExecuteTest(string testMethodName) { dynamic result = null; try { result = _sc.Run(testMethodName, new object[] { }); } catch { var error = ((IScriptControl)_sc).Error; if (error != null) { var description = error.Description; var line = error.Line; var column = error.Column; var text = error.Text; var source = error.Source; if (_context != null) { var details = String.Format("{0} \r\nLine: {1} Column: {2}", source, line, column); _context.WriteLine(details); } } throw new AssertFailedException(error.Description); } } public void Dispose() { _sc = null; } } }     Notice that the JavaScriptTestHelper class requires a Test Context to be instantiated. For this reason, you can use the JavaScriptTestHelper only with a Visual Studio Unit Test and not a Basic Unit Test (These are two different types of Visual Studio project items). Add the JavaScriptTestHelper file to your MVC test application (for example, MvcApplication1.Tests). Creating the JavaScript Unit Test Next, we need to create the JavaScript unit test function that we will use to test the addNumbers() function. Create a folder in your MVC test project named JavaScriptTests and add the following JavaScript file to this folder: MvcApplication1.Tests\JavaScriptTests\MathTest.js /// <reference path="JavaScriptUnitTestFramework.js"/> function testAddNumbers() { // Act var result = addNumbers(1, 3); // Assert assert.areEqual(4, result, "addNumbers did not return right value!"); }   The testAddNumbers() function takes advantage of another JavaScript library named JavaScriptUnitTestFramework.js. This library contains all of the code necessary to make assertions. Add the following JavaScriptnitTestFramework.js to the same folder as the MathTest.js file: MvcApplication1.Tests\JavaScriptTests\JavaScriptUnitTestFramework.js var assert = { areEqual: function (expected, actual, message) { if (expected !== actual) { throw new Error("Expected value " + expected + " is not equal to " + actual + ". " + message); } } }; There is only one type of assertion supported by this file: the areEqual() assertion. Most likely, you would want to add additional types of assertions to this file to make it easier to write your JavaScript unit tests. Deploying the JavaScript Test Files This step is non-intuitive. When you use Visual Studio to run unit tests, Visual Studio creates a new folder and executes a copy of the files in your project. After you run your unit tests, your Visual Studio Solution will contain a new folder named TestResults that includes a subfolder for each test run. You need to configure Visual Studio to deploy your JavaScript files to the test run folder or Visual Studio won’t be able to find your JavaScript files when you execute your unit tests. You will get an error that looks something like this when you attempt to execute your unit tests: You can configure Visual Studio to deploy your JavaScript files by adding a Test Settings file to your Visual Studio Solution. It is important to understand that you need to add this file to your Visual Studio Solution and not a particular Visual Studio project. Right-click your Solution in the Solution Explorer window and select the menu option Add, New Item. Select the Test Settings item and click the Add button. After you create a Test Settings file for your solution, you can indicate that you want a particular folder to be deployed whenever you perform a test run. Select the menu option Test, Edit Test Settings to edit your test configuration file. Select the Deployment tab and select your MVC test project’s JavaScriptTest folder to deploy. Click the Apply button and the Close button to save the changes and close the dialog. Creating the Visual Studio Unit Test The very last step is to create the Visual Studio unit test (the MS Test unit test). Add a new unit test to your MVC test project by selecting the menu option Add New Item and selecting the Unit Test project item (Do not select the Basic Unit Test project item): The difference between a Basic Unit Test and a Unit Test is that a Unit Test includes a Test Context. We need this Test Context to use the JavaScriptTestHelper class that we created earlier. Enter the following test method for the new unit test: [TestMethod] public void TestAddNumbers() { var jsHelper = new JavaScriptTestHelper(this.TestContext); // Load JavaScript files jsHelper.LoadFile("JavaScriptUnitTestFramework.js"); jsHelper.LoadFile(@"..\..\..\MvcApplication1\Scripts\Math.js"); jsHelper.LoadFile("MathTest.js"); // Execute JavaScript Test jsHelper.ExecuteTest("testAddNumbers"); } This code uses the JavaScriptTestHelper to load three files: JavaScripUnitTestFramework.js – Contains the assert functions. Math.js – Contains the addNumbers() function from your MVC application which is being tested. MathTest.js – Contains the JavaScript unit test function. Next, the test method calls the JavaScriptTestHelper ExecuteTest() method to execute the testAddNumbers() JavaScript function. Running the Visual Studio JavaScript Unit Test After you complete all of the steps described above, you can execute the JavaScript unit test just like any other unit test. You can use the keyboard combination CTRL-R, CTRL-A to run all of the tests in the current Visual Studio Solution. Alternatively, you can use the buttons in the Visual Studio toolbar to run the tests: (Unfortunately, the Run All Impacted Tests button won’t work correctly because Visual Studio won’t detect that your JavaScript code has changed. Therefore, you should use either the Run Tests in Current Context or Run All Tests in Solution options instead.) The results of running the JavaScript tests appear side-by-side with the results of running the server tests in the Test Results window. For example, if you Run All Tests in Solution then you will get the following results: Notice that the TestAddNumbers() JavaScript test has failed. That is good because our addNumbers() function is hard-coded to always return the value 5. If you double-click the failing JavaScript test, you can view additional details such as the JavaScript error message and the line number of the JavaScript code that failed: Summary The goal of this blog entry was to explain an approach to creating JavaScript unit tests that can be easily integrated with Visual Studio and Visual Studio ALM. I described how you can use the Microsoft Script Control to execute JavaScript on the server. By taking advantage of the Microsoft Script Control, we were able to execute our JavaScript unit tests side-by-side with all of our other unit tests and view the results in the standard Visual Studio Test Results window. You can download the code discussed in this blog entry from here: http://StephenWalther.com/downloads/Blog/JavaScriptUnitTesting/JavaScriptUnitTests.zip Before running this code, you need to first install the Microsoft Script Control which you can download from here: http://www.microsoft.com/downloads/en/details.aspx?FamilyID=d7e31492-2595-49e6-8c02-1426fec693ac

    Read the article

  • Oracle Insurance Unveils Next Generation of Enterprise Document Automation: Oracle Documaker Enterprise Edition

    - by helen.pitts(at)oracle.com
    Oracle today announced the introduction of Oracle Documaker Enterprise Edition, the next generation of the company's market-leading Enterprise Document Automation (EDA) solution for dynamically creating, managing and delivering adaptive enterprise communications across multiple channels. "Insurers and other organizations need enterprise document automation that puts the power to manage the complete document lifecycle in the hands of the business user," said Srini Venkatasanthanam, vice president, Product Strategy, Oracle Insurancein the press release. "Built with features such as rules-based configurability and interactive processing, Oracle Documaker Enterprise Edition makes possible an adaptive approach to enterprise document automation - documents when, where and in the form they're needed." Key enhancements in Oracle Documaker Enterprise Edition include: Documaker Interactive, the newly renamed and redesigned Web-based iDocumaker module. Documaker Interactive enables users to quickly and interactively create and assemble compliant communications such as policy and claims correspondence directly from their desktops. Users benefits from built-in accelerators and rules-based configurability, pre-configured content as well as embedded workflow leveraging Oracle BPEL Process Manager. Documaker Documaker Factory, which helps enterprises reduce cost and improve operational efficiency through better management of their enterprise publishing operations. Dashboards, analytics, reporting and an administrative console provide insurers with greater insight and centralized control over document production allowing them to better adapt their resources based on business demands. Other enhancements include: enhanced business user empowerment; additional multi-language localization capabilities; and benefits from the use of powerful Oracle technologies such as the Oracle Application Development Framework for all interfaces and Oracle Universal Content Management (Oracle UCM) for enterprise content management. Drive Competitive Advantage and Growth: Deb Smallwood, founder of SMA Strategy Meets Action, a leading industry insurance analyst consulting firm and co-author of 3CM in Insurance: Customer Communications and Content Management published last month, noted in the press release that "maximum value can be gained from investments when Enterprise Document Automation (EDA) is viewed holistically and all forms of communication and all types of information are integrated across the entire enterprise. "Insurers that choose an approach that takes all communications, both structured and unstructured data, coming into the company from a wide range of channels, and then create seamless flows of information will have a real competitive advantage," Smallwood said. "This capability will soon become essential for selling, servicing, and ultimately driving growth through new business and retention." Learn More: Click here to watch a short flash demo that demonstrates the real business value offered by Oracle Documaker Enterprise Edition. You can also see how an insurance company can use Oracle Documaker Enterprise Edition to dynamically create, manage and publish adaptive enterprise content throughout the insurance business lifecycle for delivery across multiple channels by visiting Alamere Insurance, a fictional model insurance company created by Oracle to showcase how Oracle applications can be leveraged within the insurance enterprise. Meet Our Newest Oracle Insurance Blogger: I'm pleased to introduce our newest Oracle Insurance blogger, Susanne Hale. Susanne, who manages product marketing for Oracle Insurance EDA solutions, will be sharing insights about this topic along with examples of how our customers are transforming their enterprise communications using Oracle Documaker Enterprise Edition in future Oracle Insurance blog entries. Helen Pitts is senior product marketing manager for Oracle Insurance.

    Read the article

  • SharePoint 2010 – SQL Server has an unsupported version 10.0.2531.0

    - by Jeff Widmer
    I am trying to perform a database attach upgrade to SharePoint Foundation 2010. At this point I am trying to attach the content database to a Web application by using Windows Powershell: Mount-SPContentDatabase -Name <DatabaseName> -DatabaseServer <ServerName> -WebApplication <URL> [-Updateuserexperience] I am following the directions from this TechNet article: Attach databases and upgrade to SharePoint Foundation 2010.  When I go to mount the content database I am receiving this error: Mount-SPContentDatabase : Could not connect to [DATABASE_SERVER] using integrated security: SQL server at [DATABASE_SERVER] has an unsupported version 10.0.2531.0. Please refer to “http://go.microsoft.com/fwlink/?LinkId=165761” for information on the minimum required SQL Server versions and how to download them. At first this did not make sense because the default SharePoint Foundation 2010 website was running just fine.  But then I realized that the default SharePoint Foundation site runs off of SQL Server Express and that I had just installed SQL Server Web Edition (since the database is greater than 4GB) and restored the database to this version of SQL Server. Checking the documentation link above I see that SharePoint Server 2010 requires a 64-bit edition of SQL Server with the minimum required SQL Server versions as follows: SQL Server 2008 Express Edition Service Pack 1, version number 10.0.2531 SQL Server 2005 Service Pack 3 cumulative update package 3, version number 9.00.4220.00 SQL Server 2008 Service Pack 1 cumulative update package 2, version number 10.00.2714.00 The version of SQL Server 2008 Web Edition with Service Pack 1 (the version I installed on this machine) is 10.0.2531.0. SELECT @@VERSION: Microsoft SQL Server 2008 (SP1) - 10.0.2531.0 (X64)   Mar 29 2009 10:11:52   Copyright (c) 1988-2008 Microsoft Corporation  Web Edition (64-bit) on Windows NT 6.1 <X64> (Build 7600: ) (VM) But I had to read the article several times since the minimum version number for SQL Server Express is 10.0.2531.0.  At first I thought I was good with the version of SQL Server 2008 Web that I had installed, also 10.0.2531.0.  But then I read further to see that there is a cumulative update (hotfix) for SQL Server 2008 SP1 (NOT the Express edition) that is required for SharePoint 2010 and will bump the version number to 10.0.2714.00. So the solution was to install the Cumulative update package 2 for SQL Server 2008 Service Pack 1 on my SQL Server 2008 Web Edition to allow SharePoint 2010 to work with SQL Server 2008 (other than the SQL Server 2008 Express version). SELECT @@VERSION (After installing Cumulative update package 2): Microsoft SQL Server 2008 (SP1) - 10.0.2714.0 (X64)   May 14 2009 16:08:52   Copyright (c) 1988-2008 Microsoft Corporation  Web Edition (64-bit) on Windows NT 6.1 <X64> (Build 7600: ) (VM)

    Read the article

  • Dividing web.config into multiple files in asp.net

    - by Jalpesh P. Vadgama
    When you are having different people working on one project remotely you will get some problem with web.config, as everybody was having different version of web.config. So at that time once you check in your web.config with your latest changes the other people have to get latest that web.config and made some specific changes as per their local environment. Most of people who have worked things from remotely has faced that problem. I think most common example would be connection string and app settings changes. For this kind of situation this will be a best solution. We can divide particular section of web.config into the multiple files. For example we could have separate ConnectionStrings.config file for connection strings and AppSettings.config file for app settings file. Most of people does not know that there is attribute called ‘configSource’ where we can  define the path of external config file and it will load that section from that external file. Just like below. <configuration> <appSettings configSource="AppSettings.config"/> <connectionStrings configSource="ConnectionStrings.config"/> </configuration> And you could have your ConnectionStrings.config file like following. <connectionStrings> <add name="DefaultConnection" connectionString="Data Source=(LocalDb)\v11.0;Initial Catalog=aspnet-WebApplication1-20120523114732;Integrated Security=True" providerName="System.Data.SqlClient" /> </connectionStrings> Same way you have another AppSettings.Config file like following. <appSettings> <add key="aspnet:UseTaskFriendlySynchronizationContext" value="true" /> <add key="ValidationSettings:UnobtrusiveValidationMode" value="WebForms" /> </appSettings> That's it. Hope you like this post. Stay tuned for more..

    Read the article

  • SQL Server Editions and Integration Services

    The SQL Server 2005 and SQL Server 2008 product family has quite a few editions now, so what does this mean for SQL Server Integration Services? Starting from the bottom we have the free edition known as Express, and the entry level Workgroup edition, as well as the new Web edition. None of these three include the full SSIS product, but they do all include the SQL Server Import and Export Wizard, with access to basic data sources but nothing more, so for simple loading and extraction of data this should suffice. You will not be able to build packages though, this is just a one shot deal aimed at using the wizard on an ad-hoc basis. To get the full power of Integration Services you need to start with Standard edition. This includes the BI Development Studio, for building your own packages, and fully functional IDE integrated into Visual Studio. (You get the full VS 2005/2008 IDE with the product). All core functions will be available but with a restricted set of transformations and tasks. The SQL Server 2005 Features Comparison or Features Supported by the Editions of SQL Server 2008 describes standard edition as having basic transforms, compared to Enterprise which includes the advanced transforms. I think basic is a little harsh considering the power you get with Standard, but the advanced covers the truly ground-breaking capabilities of data mining, text mining and cleansing or fuzzy transforms. The power of performing these operations within your ETL pipeline should not be underestimated, but not all processes will require these capabilities, so it seems like a reasonable delineation. Thankfully there are no feature limitations or artificial governors within Standard compared to Enterprise. The same control flow and data flow engines underpin both editions, with the same configuration and deployment options allowing you to work seamlessly between environments and editions if using the common components. In fact there are no govenors at all in SSIS, so whilst the SQL Database engine is limited to 4 CPUs in Standard edition, SSIS is only limited by the base operating system. The advanced transforms only available with Enterprise edition: Data Mining Training Destination Data Mining Query Component Fuzzy Grouping Fuzzy Lookup Term Extraction Term Lookup Dimension Processing Destination Partition Processing Destination The advanced tasks only available with Enterprise edition: Data Mining Query Task So in summary, if you want SQL Server Integration Services, you need SQL Server Standard edition, and for the more advanced tasks and transforms you need SQL Server Enterprise edition. To recap, the answer to the often asked question is no, SQL Server Integration Services is not available in SQL Server Express or Workgroup editions.

    Read the article

  • Deploy ASP.NET Web Applications with Web Deployment Projects

    - by Ben Griswold
    One may quickly build and deploy an ASP.NET web application via the Publish option in Visual Studio.  This option works great for most simple deployment scenarios but it won’t always cut it.  Let’s say you need to automate your deployments. Or you have environment-specific configuration settings. Or you need to execute pre/post build operations when you do your builds.  If so, you should consider using Web Deployment Projects. The Web Deployment Project type doesn’t come out-of-the-box with Visual Studio 2008.  You’ll need to Download Visual Studio® 2008 Web Deployment Projects – RTW and install if you want to follow along with this tutorial. I’ve created a shiny new ASP.NET MVC project.  Web Deployment Projects work with websites, web applications and MVC projects so feel free to go with any web project type you’d like.  Once your web application is in place, it’s time to add the Web Deployment project.  You can hunt and peck around the File > New > New Project… dialogue as long as you’d like, but you aren’t going to find what you need.  Instead, select the web project and then choose the “Add Web Deployment Project…” hiding behind the Build menu option. I prefer to name my projects based on the environment in which I plan to deploy.  In this case, I’ll be rolling to the QA machine. Don’t expect too much to happen at this point.  A seemingly empty project with a funny icon will be added to your solution.  That’s it. I want to take a minute and talk about configuration settings before we continue.  Some of the common settings which might change from environment to environment are appSettings, connectionStrings and mailSettings.  Here’s a look at my updated web.config: <appSettings>   <add key="MvcApplication293.Url" value="http://localhost:50596/" />     </appSettings> <connectionStrings>   <add name="ApplicationServices"        connectionString="data source=.\SQLEXPRESS;Integrated Security=SSPI;AttachDBFilename=|DataDirectory|aspnetdb.mdf;User Instance=true"        providerName="System.Data.SqlClient"/> </connectionStrings>   <system.net>   <mailSettings>     <smtp from="[email protected]">         <network host="server.com" userName="username" password="password" port="587" defaultCredentials="false"/>     </smtp>   </mailSettings> </system.net> I want to update these values prior to deploying to the QA environment.  There are variations to this approach, but I like to maintain environment-specific settings for each of the web.config sections in the Config/[Environment] project folders.  I’ve provided a screenshot of the QA environment settings below. It may be obvious what one should include in each of the three files.  Basically, it is a copy of the associated web.config section with updated setting values.  For example, the AppSettings.config file may include a reference to the QA web url, the DB.config would include the QA database server and login information and the StmpSettings.config would include a QA Stmp server and user information. <?xml version="1.0" encoding="utf-8" ?> <appSettings>   <add key="MvcApplication293.Url" value="http://qa.MvcApplicatinon293.com/" /> </appSettings> AppSettings.config  <?xml version="1.0" encoding="utf-8" ?> <connectionStrings>   <add name="ApplicationServices"        connectionString="server=QAServer;integrated security=SSPI;database=MvcApplication293"        providerName="System.Data.SqlClient"/>   </connectionStrings> Db.config  <?xml version="1.0" encoding="utf-8" ?> <smtp from="[email protected]">     <network host="qaserver.com" userName="qausername" password="qapassword" port="587" defaultCredentials="false"/> </smtp> SmtpSettings.config  I think our web project is ready to deploy.  Now, it’s time to concentrate on the Web Deployment Project itself.  Right-click on the project file and open the Property Pages. The first thing to call out is the Configuration dropdown.  I only deploy a project which is built in Release Mode so I only setup the Web Deployment Project for this mode.  (This is when you change the Configuration selection to “Release.”)  I typically keep the Output Folder default value – .\Release\.  When the application is built, all artifacts will be dropped in the .\Release\ folder relative to the Web Deployment Project root.  The final option may be up for some debate.  I like to roll out updatable websites so I select the “Allow this precompiled site to be updatable” option.  I really do like to follow standard SDLC processes when I release my software but there are those times when you just have to make a hotfix to production and I like to keep this option open if need be.  If you are strongly opposed to this idea, please, by all means, don’t check the box. The next tab is boring.  I don’t like to deploy a crazy number of DLLs so I merge all outputs to a single assembly.  Again, you may have another option and feel free to change this selection if you so wish. If you follow my lead, take care when choosing a single assembly name.  The Assembly Name can not be the same as the website or any other project in your solution otherwise you’ll receive a circular reference build error.  In other words, I can’t name the assembly MvcApplication293 or my output window would start yelling at me. Remember when we called out our QA configuration files?  Click on the Deployment tab and you’ll see how where going to use them.  Notice the Web.config file section replacements value.  All this does is swap called out web.config sections with the content of the Config\QA\* files.  You can reduce or extend this list as you deem fit.  Did you see the “Use external configuration source file” option?  You know how you can point any of your web.config sections to an external file via the configSource attribute?  This option allows you to leverage that technique and instead of replacing the content of the sections, you will replace the configSource attribute value instead. <appSettings configSource="Config\QA\AppSettings.config" /> Go ahead and Apply your changes.  I’d like to take a look at the project file we just updated.  Right-click on the Web Deployment Project and select “Open Project File.” One of the first configuration blocks reflects core Release build settings.  There are a couple of points I’d like to call out here: DebugSymbols=false ensures the compilation debug attribute in your web.config is flipped to false as part of build process.  There’s some crumby (more likely old) documentation which implies you need a ToggleDebugCompilation task to make this happen.  Nope. Just make sure the DebugSymbols is set to false.  EnableUpdateable implies a single dll for the web application rather than a dll for each object and and empty view file. I think updatable applications are cleaner and include the benefit (or risk based on your perspective) that portions of the application can be updated directly on the server.  I called this out earlier but I wanted to reiterate. <PropertyGroup Condition=" '$(Configuration)|$(Platform)' == 'Release|AnyCPU' ">     <DebugSymbols>false</DebugSymbols>     <OutputPath>.\Release</OutputPath>     <EnableUpdateable>true</EnableUpdateable>     <UseMerge>true</UseMerge>     <SingleAssemblyName>MvcApplication293</SingleAssemblyName>     <DeleteAppCodeCompiledFiles>true</DeleteAppCodeCompiledFiles>     <UseWebConfigReplacement>true</UseWebConfigReplacement>     <ValidateWebConfigReplacement>true</ValidateWebConfigReplacement>     <DeleteAppDataFolder>true</DeleteAppDataFolder>   </PropertyGroup> The next section is self-explanatory.  The content merely reflects the replacement value you provided via the Property Pages. <ItemGroup Condition="'$(Configuration)|$(Platform)' == 'Release|AnyCPU'">     <WebConfigReplacementFiles Include="Config\QA\AppSettings.config">       <Section>appSettings</Section>     </WebConfigReplacementFiles>     <WebConfigReplacementFiles Include="Config\QA\Db.config">       <Section>connectionStrings</Section>     </WebConfigReplacementFiles>     <WebConfigReplacementFiles Include="Config\QA\SmtpSettings.config">       <Section>system.net/mailSettings/smtp</Section>     </WebConfigReplacementFiles>   </ItemGroup> You’ll want to extend the ItemGroup section to include the files you wish to exclude from the build.  The sample ExcludeFromBuild nodes exclude all obj, svn, csproj, user, pdb artifacts from the build. Enough though they files aren’t included in your web project, you’ll need to exclude them or they’ll show up along with required deployment artifacts.  <ItemGroup Condition="'$(Configuration)|$(Platform)' == 'Release|AnyCPU'">     <WebConfigReplacementFiles Include="Config\QA\AppSettings.config">       <Section>appSettings</Section>     </WebConfigReplacementFiles>     <WebConfigReplacementFiles Include="Config\QA\Db.config">       <Section>connectionStrings</Section>     </WebConfigReplacementFiles>     <WebConfigReplacementFiles Include="Config\QA\SmtpSettings.config">       <Section>system.net/mailSettings/smtp</Section>     </WebConfigReplacementFiles>     <ExcludeFromBuild Include="$(SourceWebPhysicalPath)\obj\**\*.*" />     <ExcludeFromBuild Include="$(SourceWebPhysicalPath)\**\.svn\**\*.*" />     <ExcludeFromBuild Include="$(SourceWebPhysicalPath)\**\.svn\**\*" />     <ExcludeFromBuild Include="$(SourceWebPhysicalPath)\**\*.csproj" />     <ExcludeFromBuild Include="$(SourceWebPhysicalPath)\**\*.user" />     <ExcludeFromBuild Include="$(SourceWebPhysicalPath)\bin\*.pdb" />     <ExcludeFromBuild Include="$(SourceWebPhysicalPath)\Notes.txt" />   </ItemGroup> Pre/post build and Pre/post merge tasks are added to the final code block.  By default, your project file should look like the following – a completely commented out section. <!– To modify your build process, add your task inside one of        the targets below and uncomment it. Other similar extension        points exist, see Microsoft.WebDeployment.targets.   <Target Name="BeforeBuild">   </Target>   <Target Name="BeforeMerge">   </Target>   <Target Name="AfterMerge">   </Target>   <Target Name="AfterBuild">   </Target>   –> Update the section to remove all temporary Config folders and files after the build.  <!– To modify your build process, add your task inside one of        the targets below and uncomment it. Other similar extension        points exist, see Microsoft.WebDeployment.targets.     <Target Name="BeforeMerge">   </Target>   <Target Name="AfterMerge">   </Target>     <Target Name="BeforeBuild">      </Target>       –>   <Target Name="AfterBuild">     <!– WebConfigReplacement requires the Config files. Remove after build. –>     <RemoveDir Directories="$(OutputPath)\Config" />   </Target> That’s it for setup.  Save the project file, flip the solution to Release Mode and build.  If there’s an issue, consult the Output window for details.  If all went well, you will find your deployment artifacts in your Web Deployment Project folder like so. Both the code source and published application will be there. Inside the Release folder you will find your “published files” and you’ll notice the Config folder is no where to be found.  In the Source folder, all project files are found with the exception of the items which were excluded from the build. I’ll wrap up this tutorial by calling out a little Web Deployment pet peeve of mine: there doesn’t appear to be a way to add an existing web deployment project to a solution.  The best I can come up with is create a new web deployment project and then copy and paste the contents of the existing project file into the new project file.  It’s not a big deal but it bugs me. Download the Solution

    Read the article

  • Toorcon14

    - by danx
    Toorcon 2012 Information Security Conference San Diego, CA, http://www.toorcon.org/ Dan Anderson, October 2012 It's almost Halloween, and we all know what that means—yes, of course, it's time for another Toorcon Conference! Toorcon is an annual conference for people interested in computer security. This includes the whole range of hackers, computer hobbyists, professionals, security consultants, press, law enforcement, prosecutors, FBI, etc. We're at Toorcon 14—see earlier blogs for some of the previous Toorcon's I've attended (back to 2003). This year's "con" was held at the Westin on Broadway in downtown San Diego, California. The following are not necessarily my views—I'm just the messenger—although I could have misquoted or misparaphrased the speakers. Also, I only reviewed some of the talks, below, which I attended and interested me. MalAndroid—the Crux of Android Infections, Aditya K. Sood Programming Weird Machines with ELF Metadata, Rebecca "bx" Shapiro Privacy at the Handset: New FCC Rules?, Valkyrie Hacking Measured Boot and UEFI, Dan Griffin You Can't Buy Security: Building the Open Source InfoSec Program, Boris Sverdlik What Journalists Want: The Investigative Reporters' Perspective on Hacking, Dave Maas & Jason Leopold Accessibility and Security, Anna Shubina Stop Patching, for Stronger PCI Compliance, Adam Brand McAfee Secure & Trustmarks — a Hacker's Best Friend, Jay James & Shane MacDougall MalAndroid—the Crux of Android Infections Aditya K. Sood, IOActive, Michigan State PhD candidate Aditya talked about Android smartphone malware. There's a lot of old Android software out there—over 50% Gingerbread (2.3.x)—and most have unpatched vulnerabilities. Of 9 Android vulnerabilities, 8 have known exploits (such as the old Gingerbread Global Object Table exploit). Android protection includes sandboxing, security scanner, app permissions, and screened Android app market. The Android permission checker has fine-grain resource control, policy enforcement. Android static analysis also includes a static analysis app checker (bouncer), and a vulnerablity checker. What security problems does Android have? User-centric security, which depends on the user to grant permission and make smart decisions. But users don't care or think about malware (the're not aware, not paranoid). All they want is functionality, extensibility, mobility Android had no "proper" encryption before Android 3.0 No built-in protection against social engineering and web tricks Alternative Android app markets are unsafe. Simply visiting some markets can infect Android Aditya classified Android Malware types as: Type A—Apps. These interact with the Android app framework. For example, a fake Netflix app. Or Android Gold Dream (game), which uploads user files stealthy manner to a remote location. Type K—Kernel. Exploits underlying Linux libraries or kernel Type H—Hybrid. These use multiple layers (app framework, libraries, kernel). These are most commonly used by Android botnets, which are popular with Chinese botnet authors What are the threats from Android malware? These incude leak info (contacts), banking fraud, corporate network attacks, malware advertising, malware "Hackivism" (the promotion of social causes. For example, promiting specific leaders of the Tunisian or Iranian revolutions. Android malware is frequently "masquerated". That is, repackaged inside a legit app with malware. To avoid detection, the hidden malware is not unwrapped until runtime. The malware payload can be hidden in, for example, PNG files. Less common are Android bootkits—there's not many around. What they do is hijack the Android init framework—alteering system programs and daemons, then deletes itself. For example, the DKF Bootkit (China). Android App Problems: no code signing! all self-signed native code execution permission sandbox — all or none alternate market places no robust Android malware detection at network level delayed patch process Programming Weird Machines with ELF Metadata Rebecca "bx" Shapiro, Dartmouth College, NH https://github.com/bx/elf-bf-tools @bxsays on twitter Definitions. "ELF" is an executable file format used in linking and loading executables (on UNIX/Linux-class machines). "Weird machine" uses undocumented computation sources (I think of them as unintended virtual machines). Some examples of "weird machines" are those that: return to weird location, does SQL injection, corrupts the heap. Bx then talked about using ELF metadata as (an uintended) "weird machine". Some ELF background: A compiler takes source code and generates a ELF object file (hello.o). A static linker makes an ELF executable from the object file. A runtime linker and loader takes ELF executable and loads and relocates it in memory. The ELF file has symbols to relocate functions and variables. ELF has two relocation tables—one at link time and another one at loading time: .rela.dyn (link time) and .dynsym (dynamic table). GOT: Global Offset Table of addresses for dynamically-linked functions. PLT: Procedure Linkage Tables—works with GOT. The memory layout of a process (not the ELF file) is, in order: program (+ heap), dynamic libraries, libc, ld.so, stack (which includes the dynamic table loaded into memory) For ELF, the "weird machine" is found and exploited in the loader. ELF can be crafted for executing viruses, by tricking runtime into executing interpreted "code" in the ELF symbol table. One can inject parasitic "code" without modifying the actual ELF code portions. Think of the ELF symbol table as an "assembly language" interpreter. It has these elements: instructions: Add, move, jump if not 0 (jnz) Think of symbol table entries as "registers" symbol table value is "contents" immediate values are constants direct values are addresses (e.g., 0xdeadbeef) move instruction: is a relocation table entry add instruction: relocation table "addend" entry jnz instruction: takes multiple relocation table entries The ELF weird machine exploits the loader by relocating relocation table entries. The loader will go on forever until told to stop. It stores state on stack at "end" and uses IFUNC table entries (containing function pointer address). The ELF weird machine, called "Brainfu*k" (BF) has: 8 instructions: pointer inc, dec, inc indirect, dec indirect, jump forward, jump backward, print. Three registers - 3 registers Bx showed example BF source code that implemented a Turing machine printing "hello, world". More interesting was the next demo, where bx modified ping. Ping runs suid as root, but quickly drops privilege. BF modified the loader to disable the library function call dropping privilege, so it remained as root. Then BF modified the ping -t argument to execute the -t filename as root. It's best to show what this modified ping does with an example: $ whoami bx $ ping localhost -t backdoor.sh # executes backdoor $ whoami root $ The modified code increased from 285948 bytes to 290209 bytes. A BF tool compiles "executable" by modifying the symbol table in an existing ELF executable. The tool modifies .dynsym and .rela.dyn table, but not code or data. Privacy at the Handset: New FCC Rules? "Valkyrie" (Christie Dudley, Santa Clara Law JD candidate) Valkyrie talked about mobile handset privacy. Some background: Senator Franken (also a comedian) became alarmed about CarrierIQ, where the carriers track their customers. Franken asked the FCC to find out what obligations carriers think they have to protect privacy. The carriers' response was that they are doing just fine with self-regulation—no worries! Carriers need to collect data, such as missed calls, to maintain network quality. But carriers also sell data for marketing. Verizon sells customer data and enables this with a narrow privacy policy (only 1 month to opt out, with difficulties). The data sold is not individually identifiable and is aggregated. But Verizon recommends, as an aggregation workaround to "recollate" data to other databases to identify customers indirectly. The FCC has regulated telephone privacy since 1934 and mobile network privacy since 2007. Also, the carriers say mobile phone privacy is a FTC responsibility (not FCC). FTC is trying to improve mobile app privacy, but FTC has no authority over carrier / customer relationships. As a side note, Apple iPhones are unique as carriers have extra control over iPhones they don't have with other smartphones. As a result iPhones may be more regulated. Who are the consumer advocates? Everyone knows EFF, but EPIC (Electrnic Privacy Info Center), although more obsecure, is more relevant. What to do? Carriers must be accountable. Opt-in and opt-out at any time. Carriers need incentive to grant users control for those who want it, by holding them liable and responsible for breeches on their clock. Location information should be added current CPNI privacy protection, and require "Pen/trap" judicial order to obtain (and would still be a lower standard than 4th Amendment). Politics are on a pro-privacy swing now, with many senators and the Whitehouse. There will probably be new regulation soon, and enforcement will be a problem, but consumers will still have some benefit. Hacking Measured Boot and UEFI Dan Griffin, JWSecure, Inc., Seattle, @JWSdan Dan talked about hacking measured UEFI boot. First some terms: UEFI is a boot technology that is replacing BIOS (has whitelisting and blacklisting). UEFI protects devices against rootkits. TPM - hardware security device to store hashs and hardware-protected keys "secure boot" can control at firmware level what boot images can boot "measured boot" OS feature that tracks hashes (from BIOS, boot loader, krnel, early drivers). "remote attestation" allows remote validation and control based on policy on a remote attestation server. Microsoft pushing TPM (Windows 8 required), but Google is not. Intel TianoCore is the only open source for UEFI. Dan has Measured Boot Tool at http://mbt.codeplex.com/ with a demo where you can also view TPM data. TPM support already on enterprise-class machines. UEFI Weaknesses. UEFI toolkits are evolving rapidly, but UEFI has weaknesses: assume user is an ally trust TPM implicitly, and attached to computer hibernate file is unprotected (disk encryption protects against this) protection migrating from hardware to firmware delays in patching and whitelist updates will UEFI really be adopted by the mainstream (smartphone hardware support, bank support, apathetic consumer support) You Can't Buy Security: Building the Open Source InfoSec Program Boris Sverdlik, ISDPodcast.com co-host Boris talked about problems typical with current security audits. "IT Security" is an oxymoron—IT exists to enable buiness, uptime, utilization, reporting, but don't care about security—IT has conflict of interest. There's no Magic Bullet ("blinky box"), no one-size-fits-all solution (e.g., Intrusion Detection Systems (IDSs)). Regulations don't make you secure. The cloud is not secure (because of shared data and admin access). Defense and pen testing is not sexy. Auditors are not solution (security not a checklist)—what's needed is experience and adaptability—need soft skills. Step 1: First thing is to Google and learn the company end-to-end before you start. Get to know the management team (not IT team), meet as many people as you can. Don't use arbitrary values such as CISSP scores. Quantitive risk assessment is a myth (e.g. AV*EF-SLE). Learn different Business Units, legal/regulatory obligations, learn the business and where the money is made, verify company is protected from script kiddies (easy), learn sensitive information (IP, internal use only), and start with low-hanging fruit (customer service reps and social engineering). Step 2: Policies. Keep policies short and relevant. Generic SANS "security" boilerplate policies don't make sense and are not followed. Focus on acceptable use, data usage, communications, physical security. Step 3: Implementation: keep it simple stupid. Open source, although useful, is not free (implementation cost). Access controls with authentication & authorization for local and remote access. MS Windows has it, otherwise use OpenLDAP, OpenIAM, etc. Application security Everyone tries to reinvent the wheel—use existing static analysis tools. Review high-risk apps and major revisions. Don't run different risk level apps on same system. Assume host/client compromised and use app-level security control. Network security VLAN != segregated because there's too many workarounds. Use explicit firwall rules, active and passive network monitoring (snort is free), disallow end user access to production environment, have a proxy instead of direct Internet access. Also, SSL certificates are not good two-factor auth and SSL does not mean "safe." Operational Controls Have change, patch, asset, & vulnerability management (OSSI is free). For change management, always review code before pushing to production For logging, have centralized security logging for business-critical systems, separate security logging from administrative/IT logging, and lock down log (as it has everything). Monitor with OSSIM (open source). Use intrusion detection, but not just to fulfill a checkbox: build rules from a whitelist perspective (snort). OSSEC has 95% of what you need. Vulnerability management is a QA function when done right: OpenVas and Seccubus are free. Security awareness The reality is users will always click everything. Build real awareness, not compliance driven checkbox, and have it integrated into the culture. Pen test by crowd sourcing—test with logging COSSP http://www.cossp.org/ - Comprehensive Open Source Security Project What Journalists Want: The Investigative Reporters' Perspective on Hacking Dave Maas, San Diego CityBeat Jason Leopold, Truthout.org The difference between hackers and investigative journalists: For hackers, the motivation varies, but method is same, technological specialties. For investigative journalists, it's about one thing—The Story, and they need broad info-gathering skills. J-School in 60 Seconds: Generic formula: Person or issue of pubic interest, new info, or angle. Generic criteria: proximity, prominence, timeliness, human interest, oddity, or consequence. Media awareness of hackers and trends: journalists becoming extremely aware of hackers with congressional debates (privacy, data breaches), demand for data-mining Journalists, use of coding and web development for Journalists, and Journalists busted for hacking (Murdock). Info gathering by investigative journalists include Public records laws. Federal Freedom of Information Act (FOIA) is good, but slow. California Public Records Act is a lot stronger. FOIA takes forever because of foot-dragging—it helps to be specific. Often need to sue (especially FBI). CPRA is faster, and requests can be vague. Dumps and leaks (a la Wikileaks) Journalists want: leads, protecting ourselves, our sources, and adapting tools for news gathering (Google hacking). Anonomity is important to whistleblowers. They want no digital footprint left behind (e.g., email, web log). They don't trust encryption, want to feel safe and secure. Whistleblower laws are very weak—there's no upside for whistleblowers—they have to be very passionate to do it. Accessibility and Security or: How I Learned to Stop Worrying and Love the Halting Problem Anna Shubina, Dartmouth College Anna talked about how accessibility and security are related. Accessibility of digital content (not real world accessibility). mostly refers to blind users and screenreaders, for our purpose. Accessibility is about parsing documents, as are many security issues. "Rich" executable content causes accessibility to fail, and often causes security to fail. For example MS Word has executable format—it's not a document exchange format—more dangerous than PDF or HTML. Accessibility is often the first and maybe only sanity check with parsing. They have no choice because someone may want to read what you write. Google, for example, is very particular about web browser you use and are bad at supporting other browsers. Uses JavaScript instead of links, often requiring mouseover to display content. PDF is a security nightmare. Executible format, embedded flash, JavaScript, etc. 15 million lines of code. Google Chrome doesn't handle PDF correctly, causing several security bugs. PDF has an accessibility checker and PDF tagging, to help with accessibility. But no PDF checker checks for incorrect tags, untagged content, or validates lists or tables. None check executable content at all. The "Halting Problem" is: can one decide whether a program will ever stop? The answer, in general, is no (Rice's theorem). The same holds true for accessibility checkers. Language-theoretic Security says complicated data formats are hard to parse and cannot be solved due to the Halting Problem. W3C Web Accessibility Guidelines: "Perceivable, Operable, Understandable, Robust" Not much help though, except for "Robust", but here's some gems: * all information should be parsable (paraphrasing) * if not parsable, cannot be converted to alternate formats * maximize compatibility in new document formats Executible webpages are bad for security and accessibility. They say it's for a better web experience. But is it necessary to stuff web pages with JavaScript for a better experience? A good example is The Drudge Report—it has hand-written HTML with no JavaScript, yet drives a lot of web traffic due to good content. A bad example is Google News—hidden scrollbars, guessing user input. Solutions: Accessibility and security problems come from same source Expose "better user experience" myth Keep your corner of Internet parsable Remember "Halting Problem"—recognize false solutions (checking and verifying tools) Stop Patching, for Stronger PCI Compliance Adam Brand, protiviti @adamrbrand, http://www.picfun.com/ Adam talked about PCI compliance for retail sales. Take an example: for PCI compliance, 50% of Brian's time (a IT guy), 960 hours/year was spent patching POSs in 850 restaurants. Often applying some patches make no sense (like fixing a browser vulnerability on a server). "Scanner worship" is overuse of vulnerability scanners—it gives a warm and fuzzy and it's simple (red or green results—fix reds). Scanners give a false sense of security. In reality, breeches from missing patches are uncommon—more common problems are: default passwords, cleartext authentication, misconfiguration (firewall ports open). Patching Myths: Myth 1: install within 30 days of patch release (but PCI §6.1 allows a "risk-based approach" instead). Myth 2: vendor decides what's critical (also PCI §6.1). But §6.2 requires user ranking of vulnerabilities instead. Myth 3: scan and rescan until it passes. But PCI §11.2.1b says this applies only to high-risk vulnerabilities. Adam says good recommendations come from NIST 800-40. Instead use sane patching and focus on what's really important. From NIST 800-40: Proactive: Use a proactive vulnerability management process: use change control, configuration management, monitor file integrity. Monitor: start with NVD and other vulnerability alerts, not scanner results. Evaluate: public-facing system? workstation? internal server? (risk rank) Decide:on action and timeline Test: pre-test patches (stability, functionality, rollback) for change control Install: notify, change control, tickets McAfee Secure & Trustmarks — a Hacker's Best Friend Jay James, Shane MacDougall, Tactical Intelligence Inc., Canada "McAfee Secure Trustmark" is a website seal marketed by McAfee. A website gets this badge if they pass their remote scanning. The problem is a removal of trustmarks act as flags that you're vulnerable. Easy to view status change by viewing McAfee list on website or on Google. "Secure TrustGuard" is similar to McAfee. Jay and Shane wrote Perl scripts to gather sites from McAfee and search engines. If their certification image changes to a 1x1 pixel image, then they are longer certified. Their scripts take deltas of scans to see what changed daily. The bottom line is change in TrustGuard status is a flag for hackers to attack your site. Entire idea of seals is silly—you're raising a flag saying if you're vulnerable.

    Read the article

  • 12.04lts: no network internet

    - by dgermann
    Friends-- Cannot connect reliably to ethernet nor at all to Internet: Symptoms: About 2 weeks ago did an upgrade. Have not been able to connect to ethernet nor Internet. Today, for example, boot up this System76 laptop and there was no network connection. Did sudo mount -a and got some internal network connectivity: doug@ubuntu:/sam$ ping earth PING earth (192.168.0.201) 56(84) bytes of data. 64 bytes from earth (192.168.0.201): icmp_req=1 ttl=64 time=0.160 ms 64 bytes from earth (192.168.0.201): icmp_req=2 ttl=64 time=0.177 ms 64 bytes from earth (192.168.0.201): icmp_req=3 ttl=64 time=0.159 ms ^C --- earth ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1998ms rtt min/avg/max/mdev = 0.159/0.165/0.177/0.013 ms doug@ubuntu:/sam$ ping doug2 PING doug (192.168.0.4) 56(84) bytes of data. ^C --- doug ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 1999ms doug@ubuntu:/sam$ ping sharon PING sharon (192.168.0.111) 56(84) bytes of data. 64 bytes from sharon (192.168.0.111): icmp_req=1 ttl=128 time=0.276 ms ^C --- sharon ping statistics --- 6 packets transmitted, 1 received, 83% packet loss, time 5031ms rtt min/avg/max/mdev = 0.276/0.276/0.276/0.000 ms doug@ubuntu:/sam$ ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 4999ms doug@ubuntu:/sam$ ping earth PING earth (192.168.0.201) 56(84) bytes of data. ^C --- earth ping statistics --- 5 packets transmitted, 0 received, 100% packet loss, time 4032ms doug@ubuntu:/sam$ ping yahoo.com ping: unknown host yahoo.com doug@ubuntu:/sam$ ping ubuntu.com ping: unknown host ubuntu.com doug@ubuntu:/sam$ ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 14 packets transmitted, 0 received, 100% packet loss, time 13103ms Note that earth is the cifs server, and one time pinging it worked, later failed. Clues: doug@ubuntu:/sam$ grep -i eth /var/log/syslog |tail Aug 23 15:32:46 ubuntu kernel: [ 5328.070401] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 Aug 23 15:32:48 ubuntu kernel: [ 5330.651139] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=19090 PROTO=2 Aug 23 15:34:51 ubuntu kernel: [ 5453.072279] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 Aug 23 15:34:55 ubuntu kernel: [ 5457.085433] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16137 PROTO=2 Aug 23 15:36:56 ubuntu kernel: [ 5578.074492] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 Aug 23 15:37:00 ubuntu kernel: [ 5582.359006] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16150 PROTO=2 Aug 23 15:39:01 ubuntu kernel: [ 5703.074410] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 Aug 23 15:39:03 ubuntu kernel: [ 5705.070122] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16163 PROTO=2 Aug 23 15:41:06 ubuntu kernel: [ 5828.074387] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 Aug 23 15:41:13 ubuntu kernel: [ 5835.319941] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=23298 PROTO=2 doug@ubuntu:/sam$ ifconfig -a eth0 Link encap:Ethernet HWaddr [BLANKED] inet addr:192.168.0.7 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21b:fcff:fe29:9dfc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3961 errors:0 dropped:0 overruns:0 frame:0 TX packets:2007 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:991204 (991.2 KB) TX bytes:252908 (252.9 KB) Interrupt:16 Base address:0xec00 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2190 errors:0 dropped:0 overruns:0 frame:0 TX packets:2190 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:168052 (168.0 KB) TX bytes:168052 (168.0 KB) wlan0 Link encap:Ethernet HWaddr 00:19:d2:72:5a:0c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) doug@ubuntu:/sam$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. doug@ubuntu:/sam$ lsmod Module Size Used by des_generic 21191 0 md4 12523 0 nls_iso8859_1 12617 1 nls_cp437 12751 1 vfat 17308 1 fat 55605 1 vfat usb_storage 39646 1 dm_crypt 22528 1 joydev 17393 0 snd_hda_codec_analog 75395 1 snd_hda_intel 32719 2 pcmcia 39826 0 snd_hda_codec 109562 2 snd_hda_codec_analog,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec ip6t_LOG 16846 4 xt_hl 12465 6 ip6t_rt 12473 3 snd_pcm 80916 2 snd_hda_intel,snd_hda_codec nf_conntrack_ipv6 13581 7 nf_defrag_ipv6 13175 1 nf_conntrack_ipv6 ipt_REJECT 12512 1 ipt_LOG 12783 5 xt_limit 12541 12 xt_tcpudp 12531 21 xt_addrtype 12596 4 snd_seq_midi 13132 0 xt_state 12514 14 ip6table_filter 12711 1 ip6_tables 22528 3 ip6t_LOG,ip6t_rt,ip6table_filter nf_conntrack_netbios_ns 12585 0 nf_conntrack_broadcast 12541 1 nf_conntrack_netbios_ns nf_nat_ftp 12595 0 nf_nat 24959 1 nf_nat_ftp nf_conntrack_ipv4 19084 9 nf_nat nf_defrag_ipv4 12649 1 nf_conntrack_ipv4 nf_conntrack_ftp 13183 1 nf_nat_ftp nf_conntrack 73847 8 nf_conntrack_ipv6,xt_state,nf_conntrack_netbios_ns,nf_conntrack_broadcast,nf_nat_ftp,nf_nat,nf_conntrack_ipv4,nf_conntrack_ftp iptable_filter 12706 1 ip_tables 18106 1 iptable_filter snd_rawmidi 25424 1 snd_seq_midi psmouse 86982 0 x_tables 22011 13 ip6t_LOG,xt_hl,ip6t_rt,ipt_REJECT,ipt_LOG,xt_limit,xt_tcpudp,xt_addrtype,xt_state,ip6table_filter,ip6_tables,iptable_filter,ip_tables arc4 12473 2 r592 17808 0 snd_seq_midi_event 14475 1 snd_seq_midi memstick 15857 1 r592 yenta_socket 27465 0 serio_raw 13027 0 pcmcia_rsrc 18367 1 yenta_socket iwl3945 73186 0 pcmcia_core 21511 3 pcmcia,yenta_socket,pcmcia_rsrc iwl_legacy 71334 1 iwl3945 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event mac80211 436493 2 iwl3945,iwl_legacy snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq rfcomm 38139 0 bnep 17830 2 parport_pc 32114 0 bluetooth 158447 10 rfcomm,bnep ppdev 12849 0 cfg80211 178877 3 iwl3945,iwl_legacy,mac80211 asus_laptop 23693 0 sparse_keymap 13658 1 asus_laptop input_polldev 13648 1 asus_laptop nls_utf8 12493 6 cifs 258037 10 snd 62218 13 snd_hda_codec_analog,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd mac_hid 13077 0 snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp i915 428418 3 firewire_ohci 40172 0 sdhci_pci 18324 0 sdhci 28241 1 sdhci_pci firewire_core 56940 1 firewire_ohci crc_itu_t 12627 1 firewire_core r8169 56396 0 drm_kms_helper 45466 1 i915 drm 197641 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19115 1 i915 doug@ubuntu:/sam$ dmesg |grep eth [ 0.116936] i2c-core: driver [aat2870] using legacy suspend method [ 0.116939] i2c-core: driver [aat2870] using legacy resume method [ 1.453811] r8169 0000:03:07.0: eth0: RTL8169sb/8110sb at 0xf840ec00, [BLANKED], XID 10000000 IRQ 16 [ 1.453815] r8169 0000:03:07.0: eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok] [ 25.681231] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 154.037318] r8169 0000:03:07.0: eth0: link down [ 154.037329] r8169 0000:03:07.0: eth0: link down [ 154.037596] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 155.583162] r8169 0000:03:07.0: eth0: link up [ 155.583366] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 156.637048] r8169 0000:03:07.0: eth0: link down [ 156.637066] r8169 0000:03:07.0: eth0: link down [ 156.637339] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 156.773699] r8169 0000:03:07.0: eth0: link down [ 156.773983] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 158.456181] r8169 0000:03:07.0: eth0: link up [ 158.456378] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 159.364468] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 162.384496] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=38877 PROTO=2 [ 166.272457] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 166.422333] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=40695 PROTO=2 [ 168.736049] eth0: no IPv6 routers present [ 183.572472] r8169 0000:03:07.0: eth0: link down [ 183.572490] r8169 0000:03:07.0: eth0: link down [ 183.572934] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 185.204801] r8169 0000:03:07.0: eth0: link up [ 185.205005] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 3620.680451] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 3621.068431] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 3624.912973] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=9118 PROTO=2 [ 3631.088069] eth0: no IPv6 routers present [ 3703.062980] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 3703.465330] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=9210 PROTO=2 [ 3828.062951] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 3833.617772] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=9749 PROTO=2 [ 3953.062920] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 3955.675129] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=15983 PROTO=2 [ 4078.062922] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 4078.386319] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=15997 PROTO=2 [ 4203.062899] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 4203.559241] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16011 PROTO=2 [ 4328.062833] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 4328.930922] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16027 PROTO=2 [ 4453.062811] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 4453.950224] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16039 PROTO=2 [ 4578.062742] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 4580.626432] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=13738 PROTO=2 [ 4703.062704] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 4706.310170] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=15942 PROTO=2 [ 4828.062707] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 4832.174324] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16505 PROTO=2 [ 4953.062628] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 4961.469282] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16090 PROTO=2 [ 5078.062552] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 5080.776462] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=17239 PROTO=2 [ 5203.070394] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 5205.358134] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=17665 PROTO=2 [ 5328.070401] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 5330.651139] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=19090 PROTO=2 [ 5453.072279] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 5457.085433] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16137 PROTO=2 [ 5578.074492] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 5582.359006] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16150 PROTO=2 [ 5703.074410] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 5705.070122] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED]--- SRC=192.168.0.10 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=16163 PROTO=2 [ 5828.074387] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED][BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 5835.319941] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED][BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=23298 PROTO=2 [ 5953.074429] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED][BLANKED]--- SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 [ 5961.925481] [UFW BLOCK] IN=eth0 OUT= MAC=[BLANKED][BLANKED]--- SRC=192.168.0.5 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=24261 PROTO=2 doug@ubuntu:/sam$ lspci -nnk |grep -iA2 eth 03:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8169 PCI Gigabit Ethernet Controller [10ec:8169] (rev 10) Subsystem: ASUSTeK Computer Inc. Device [1043:11e5] Kernel driver in use: r8169 doug@ubuntu:/sam$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 doug@ubuntu:/sam$ nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Ifupdown (eth0)] ---------------------------------------------- Type: Wired Driver: r8169 State: connected Default: yes HW Address: [BLANKED] Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwl3945 State: disconnected Default: no HW Address: 00:19:D2:72:5A:0C Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points ATT592: Infra, 30:60:23:76:FE:60, Freq 2437 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 doug@ubuntu:/sam$ nslookup ubuntu.com ;; connection timed out; no servers could be reached doug@ubuntu:/sam$ dig ubuntuforums.org ; <<>> DiG 9.8.1-P1 <<>> ubuntuforums.org ;; global options: +cmd ;; connection timed out; no servers could be reached doug@ubuntu:/sam$ sudo ifconfig eth0 up doug@ubuntu:/sam$ dhcpcd eth0 The program 'dhcpcd' can be found in the following packages: * dhcpcd * dhcpcd5 Try: sudo apt-get install <selected package> doug@ubuntu:/sam$ lspci -k 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) Subsystem: ASUSTeK Computer Inc. Device 1252 Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) Subsystem: ASUSTeK Computer Inc. Device 1252 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel modules: leds-ss4200, iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: ata_piix 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel modules: i2c-i801 02:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) Subsystem: Intel Corporation PRO/Wireless 3945ABG Network Connection Kernel driver in use: iwl3945 Kernel modules: iwl3945 03:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: yenta_cardbus Kernel modules: yenta_socket 03:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci 03:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 08) Subsystem: ASUSTeK Computer Inc. Device 1297 Kernel driver in use: r592 Kernel modules: r592 03:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8169 PCI Gigabit Ethernet Controller (rev 10) Subsystem: ASUSTeK Computer Inc. Device 11e5 Kernel driver in use: r8169 Kernel modules: r8169 doug@ubuntu:/sam$ Things I have tried: sudo start network-manager: no help gksudo gedit /etc/network/interfaces changed line to iface eth0 inet dhcp: no help gksudo gedit /etc/NetworkManager/NetworkManager.conf, I changed managed=false to managed=true. Then sudo service network-manager restart: no help: network is unreachable sudo pkill -9 NetworkManager: no help gksudo gedit /etc/resolve.conf added line nameseriver 8.8.8.8: no help I know very little about networking; to date this has simply worked. Thanks for your help! :- Doug.

    Read the article

  • The Importance of a Security Assessment - by Michael Terra, Oracle

    - by Darin Pendergraft
    Today's Blog was written by Michael Terra, who was the Subject Matter Expert for the recently announced Oracle Online Security Assessment. You can take the Online Assessment here: Take the Online Assessment Over the past decade, IT Security has become a recognized and respected Business discipline.  Several factors have contributed to IT Security becoming a core business and organizational enabler including, but not limited to, increased external threats and increased regulatory pressure. Security is also viewed as a key enabler for strategic corporate activities such as mergers and acquisitions.Now, the challenge for senior security professionals is to develop an ongoing dialogue within their organizations about the importance of information security and how it can impact their organization's strategic objectives/mission. The importance of conducting regular “Security Assessments” across the IT and physical infrastructure has become increasingly important. Security standards and frameworks, such as the international standard ISO 27001, are increasingly being adopted by organizations and their business partners as proof of their security posture and “Security Assessments” are a great way to ensure a continued alignment to these frameworks.Oracle offers a number of different security assessment covering a broad range of technologies. Some of these are short engagements conducted for free with our strategic customers and partners. Others are longer term paid engagements delivered by Oracle Consulting Services or one of our partners. The goal of a security assessment, (also known as a security audit or security review), is to ensure that necessary security controls are integrated into the design and implementation of a project, application or technology.  A properly completed security assessment should provide documentation outlining any security gaps that exist in an infrastructure and the associated risks for those gaps. With that knowledge, an organization can choose to either mitigate, transfer, avoid or accept the risk. One example of an Oracle offering is a Security Readiness Assessment:The Oracle Security Readiness Assessment is a practical security architecture review focused on aligning an organization’s enterprise security architecture to their business principals and strategic objectives. The service will establish a multi-phase security architecture roadmap focused on supporting new and existing business initiatives.Offering OverviewThe Security Readiness Assessment will: Define an organization’s current security posture and provide a roadmap to a desired future state architecture by mapping  security solutions to business goals Incorporate commonly accepted security architecture concepts to streamline an organization’s security vision from strategy to implementation Define the people, process and technology implications of the desired future state architecture The objective is to deliver cohesive, best practice security architectures spanning multiple domains that are unique and specific to the context of your organization. Offering DetailsThe Oracle Security Readiness Assessment is a multi-stage process with a dedicated Oracle Security team supporting your organization.  During the course of this free engagement, the team will focus on the following: Review your current business operating model and supporting IT security structures and processes Partner with your organization to establish a future state security architecture leveraging Oracle’s reference architectures, capability maps, and best practices Provide guidance and recommendations on governance practices for the rollout and adoption of your future state security architecture Create an initial business case for the adoption of the future state security architecture If you are interested in finding out more, ask your Sales Consultant or Account Manager for details.

    Read the article

  • Talks Submitted for Ann Arbor Day of .NET 2010

    - by PSteele
    Just submitted my session abstracts for Ann Arbor's Day of .NET 2010.   Getting up to speed with .NET 3.5 -- Just in time for 4.0! Yes, C# 4.0 is just around the corner.  But if you haven't had the chance to use C# 3.5 extensively, this session will start from the ground up with the new features of 3.5.  We'll assume everyone is coming from C# 2.0.  This session will show you the details of extension methods, partial methods and more.  We'll also show you how LINQ -- Language Integrated Query -- can help decrease your development time and increase your code's readability.  If time permits, we'll look at some .NET 4.0 features, but the goal is to get you up to speed on .NET 3.5.   Go Ahead and Mock Me! When testing specific parts of your application, there can be a lot of external dependencies required to make your tests work.  Writing fake or mock objects that act as stand-ins for the real dependencies can waste a lot of time.  This is where mocking frameworks come in.  In this session, Patrick Steele will introduce you to Rhino Mocks, a popular mocking framework for .NET.  You'll see how a mocking framework can make writing unit tests easier and leads to less brittle unit tests.   Inversion of Control: Who's got control and why is it being inverted? No doubt you've heard of "Inversion of Control".  If not, maybe you've heard the term "Dependency Injection"?  The two usually go hand-in-hand.  Inversion of Control (IoC) along with Dependency Injection (DI) helps simplify the connections and lifetime of all of the dependent objects in the software you write.  In this session, Patrick Steele will introduce you to the concepts of IoC and DI and will show you how to use a popular IoC container (Castle Windsor) to help simplify the way you build software and how your objects interact with each other. If you're interested in speaking, hurry up and get your submissions in!  The deadline is Monday, April 5th! Technorati Tags: .NET,Ann Arbor,Day of .NET

    Read the article

  • Microsoft Templates included in jQuery 1.5!

    - by Stephen Walther
    When I joined the ASP.NET team as the Program Manager for Ajax, the ASP.NET team was working on releasing a new version of the Microsoft Ajax Library. This new version of the Microsoft Ajax Library had several really innovative and unique features such as support for client templates, client data-binding, script dependency management, and globalization. However, we kept hearing the message that our customers wanted to use jQuery when building ASP.NET applications. Therefore, about ten months ago, we decided to pursue a risky strategy. Scott Guthrie sent me to Cambridge to meet with John Resig – the creator of jQuery and leader of the jQuery project – to find out whether Microsoft and jQuery could work together. We wanted to find out whether the jQuery project would be open to allowing Microsoft to contribute the innovative features that we were developing for the Microsoft Ajax Library -- such as client templates and client data-binding -- to the jQuery library. Fortunately, the Cambridge meeting with Resig went well. John Resig was very open to accepting contributions to the jQuery library. Over the next few months, we worked out a process for Microsoft to contribute new features to the open-source jQuery project. Resig and Guthrie appeared on stage at the MIX10 conference to announce that Microsoft would be contributing features to jQuery. It has been a long journey, but I am happy to report success. Today, Microsoft and the jQuery project have announced that three plugins developed by developers on the ASP.NET team – the jQuery Templates, jQuery Data Link, and jQuery Globalization plugins – have been accepted as official jQuery plugins. In addition, the jQuery Templates plugin will be integrated into jQuery 1.5 which is the next major release of jQuery. You can learn more about the plugins by watching the following Web Camps TV episode hosted by James Senior with Stephen Walther: Web Camps TV #5 - Microsoft Commits Code to jQuery! You can read Scott Guthrie’s blog announcement here: http://weblogs.asp.net/scottgu/archive/2010/10/04/jquery-templates-data-link-and-globalization-accepted-as-official-jquery-plugins.aspx You can read the jQuery team’s announcement here: http://blog.jquery.com/2010/10/04/new-official-jquery-plugins-provide-templating-data-linking-and-globalization/ I wrote the original proposal for the jQuery Templates plugin. Dave Reed and Boris Moore were the ASP.NET developers responsible for actually writing the plugin (with lots of input from the jQuery team and the jQuery community). Boris has written a great set of tutorials on the Templates plugin. The first tutorial in his series is located here: http://www.borismoore.com/2010/09/introducing-jquery-templates-1-first.html I want to thank John Resig, Richard Worth, Scott Gonzalez, Rey Bango, Jorn Zaefferer, Karl Swedberg and all of the other members of the jQuery team for working with the ASP.NET team and accepting our contributions to the jQuery project.

    Read the article

  • Measuring Social Media Efforts

    - by David Dorf
    So you're on the bandwagon and you've created a Facebook page, you're tweeting everyday, and maybe you've even got a YouTube channel. Now what? After you put any program in place, you need to measure, set new goals, then execute and this is no different. But how does one measure social media efforts? First, I guess we need some goals. Typical ones might be to acquire customers, engage them, then convert them. So that translates to: Increase Facebook fans and Twitter followers Increase comments/posting and retweets Increase redemption of offers via Facebook and Twitter Counting fans and followers is easy, and tracking the redemption of coupons isn't that hard either, but measuring engagement is a tough one. How do you know whether your fans are reading your posts, and whether your posts have any meaning to them? For Facebook, the fan page administrator has access to analytics called Facebook Insights. There you can check weekly metrics such as total fans, new fans, lost fans, demographics of fans, number of postings, numbers clicks, etc. Not nearly as comprehensive as Google Analytics, but well on its way. For Twitter, getting information is a little tougher. Again, its easy to track followers and you can use tools like TweetMeme to encourage and track retweets. An interesting website called WeFollow tries to measure influence for certain topics. For example, the top three influencers for the topic "retail" are retailweek, retailwire, and retailerdaily. Other notables are #10 BestBuy, #11 GapOfficial, #12 JeffPR, and #17 OracleRetail. I assume influence is calculated based on number of followers, number of retweets, frequency of tweets, and perhaps depth of dialogs. If you want to get serious about monitoring and measuring social marketing efforts, you'd be wise to invest in a strong tool. Several are listed on this wiki, including big ones like Radian6, Nielsen, Omniture, and Buzzient. Buzzient might be particularly interesting because its integrated with Oracle CRM OnDemand -- see the demo. As always, I'm interested in hearing how others approach goal setting and monitoring of social media efforts, so feel free to post comments.

    Read the article

  • ActAs and OnBehalfOf support in WIF

    - by cibrax
    I discussed a time ago how WIF supported a new WS-Trust 1.4 element, “ActAs”, and how that element could be used for authentication delegation.  The thing is that there is another feature in WS-Trust 1.4 that also becomes handy for this kind of scenario, and I did not mention in that last post, “OnBehalfOf”. Shiung Yong wrote an excellent summary about the difference of these two new features in this forum thread. He basically commented the following, “An ActAs RST element indicates that the requestor wants a token that contains claims about two distinct entities: the requestor, and an external entity represented by the token in the ActAs element. An OnBehalfOf RST element indicates that the requestor wants a token that contains claims only about one entity: the external entity represented by the token in the OnBehalfOf element. In short, ActAs feature is typically used in scenarios that require composite delegation, where the final recipient of the issued token can inspect the entire delegation chain and see not just the client, but all intermediaries to perform access control, auditing and other related activities based on the whole identity delegation chain. The ActAs feature is commonly used in multi-tiered systems to authenticate and pass information about identities between the tiers without having to pass this information at the application/business logic layer. OnBehalfOf feature is used in scenarios where only the identity of the original client is important and is effectively the same as identity impersonation feature available in the Windows OS today. When the OnBehalfOf is used the final recipient of the issued token can only see claims about the original client, and the information about intermediaries is not preserved. One common pattern where OnBehalfOf feature is used is the proxy pattern where the client cannot access the STS directly but is instead communicating through a proxy gateway. The proxy gateway authenticates the caller and puts information about him into the OnBehalfOf element of the RST message that it then sends to the real STS for processing. The resulting token is going to contain only claims related to the client of the proxy, making the proxy completely transparent and not visible to the receiver of the issued token.” Going back to WIF, “ActAs” and “OnBehalfOf” are both supported as extensions methods in the WCF client channel. public static class ChannelFactoryOperations {   public static T CreateChannelActingAs<T>(this ChannelFactory<T> factory,     SecurityToken actAs);     public static T CreateChannelOnBehalfOf<T>(this ChannelFactory<T> factory,     SecurityToken onBehalfOf); } Both methods receive the security token with the identity of the original caller.

    Read the article

  • [MISC GEEKERY] Lucid Lynx to Come Loaded with Ubuntu One Music Store

    - by Vivek
    Ubuntu 10.04 (code name Lucid Lynx) will come loaded with the Ubuntu One music store. Rhythmbox will have the Ubuntu One music store integrated in it. It’ll also allow users to download purchased music to their local machine. Ubuntu One Music Store Users will be able to access Ubuntu One music store from the sidebar of Rhythmbox. The music store is a web page that opens in the Rhythmbox player. There are albums listed on the home page of the Ubuntu One music store page. Ubuntu One music store is powered by 7digital, which is a leading digital B2B media delivery company based in London and operating globally. Canonical, the company behind Ubuntu, has partnered with 7digital to bring the music store to it’s users, integrating it with Rhythmbox and it’s cloud storage service UbuntuOne which was launched last year. The home screen of the Ubuntu One music store displays popular albums and functionality to browse and search. You can search for Artists, Tracks, Albums, or a combination of all three. Users will also be able to browse the store alphabetically, or based on different music genres. Once you select a specific artist, all their available albums are arranged in a grid. Once an album is selected, you’ll will be able to download specific songs or the whole album. You’ll also be allowed to preview different songs for 60 seconds. You’ll be able to buy tracks using a credit card or with PayPal. The purchased tracks will be visible under Library \ Purchased from Ubuntu One. The downloaded tracks are also synced with your UbuntuOne account. This means that you’ll be able to access your tracks from any where on the web. The default UbuntuOne account comes with 2 GB free storage, however, you can also purchase additional space if you need it.   All the music is in mp3 format which is not supported by default in Ubuntu. However, you can get mp3 playback functionality using GStreamer multimedia framework. Conclusion All in all the Ubuntu One music store is a positive move to enhance the user experience and also increase the popularity of Canonical in bringing Ubuntu closer to regular users. This would also provide Canonical to make some revenue in collaboration with 7digital. Ubuntu One Music Store Wiki Similar Articles Productive Geek Tips Install GIMP 2.7.1 on Lucid Lynx using PPAExaile 0.3.0 is a Music Player for UbuntuHow to install Spotify in Ubuntu 9.10 using WineAdding extra Repositories on UbuntuSpeed Up Amarok With Large Music Collections TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Open Multiple Links At One Go NachoFoto Searches Images in Real-time Office 2010 Product Guides Google Maps Place marks – Pizza, Guns or Strip Clubs Monitor Applications With Kiwi LocPDF is a Visual PDF Search Tool

    Read the article

  • A Few Words from Oracle’s Channel Chief

    - by Meghan Fritz-Oracle
    As Oracle enters a new fiscal year, I want to take a moment and reflect on my time at Oracle thus far. The technology industry is currently at an inflection point trying to figure out where growth will come from. When you look at Oracle’s portfolio of products, it's a complete stack from applications to disc, offering differentiation in the marketplace. I was initially drawn to Oracle’s leadership, strategy, and world-class technology. Since joining the Oracle team in October 2013, I’ve had the privilege of traveling around the globe visiting our partners and customers, and wanted to share several common themes that came up during these meetings. Cloud: Many partners are trying to figure out how to build a business around the cloud. Oracle partners can currently resell or refer our cloud services. We saw over 300 percent growth from cloud resale last quarter. Engineered Systems: Hardware and software integrated together to simplify IT allows our joint customers to focus on the innovation they need to compete in a complex marketplace. We're seeing great success in a several areas, with more partners saying, “Let’s start with Oracle on Oracle.” The Internet of Things: This is the next big opportunity for device manufacturers and ISV‘s to capture market share in what is projected to be a mulit-trillion-dollar opportunity, according to Gartner.  Competition: We've got a tremendous middleware platform and a tremendous database install base. We’re not just a database company; we are a complete provider. So looking ahead, what are my priorities for fiscal 2015? Oracle PartnerNetwork has some very exciting plans on the horizon. There’s a lot more leadership and announcements to unfold, especially at this year’s Global Partner Kickoff taking place on June 25 + 26 depending on your region and time zone. I along with several other Oracle executives will be shedding light on Oracle’s strategy for the upcoming year, the latest opportunities within the OPN Specialized Program and sales strategies that will help you to continue to grow and profit with Oracle. Stay tuned for registration information next week.We also have Oracle OpenWorld and JavaOne to look forward to. These conferences are taking place in San Francisco from September 28 – October 2. We’ll have a variety of partner-specific activities for you at OPN Central @ OpenWorld including the OPN keynote, the famed AfterDark networking reception, access to the OPN Lounge and more.In the meantime, I hope that everyone has a great end to fiscal 2014.Best regards,Rich Geraffo Senior Vice President, Worldwide Alliances and Channels

    Read the article

  • AxCMS.net 10 with Microsoft Silverlight 4 and Microsoft Visual Studio 2010

    - by Axinom
    Axinom, European WCM vendor, today announced the next version of its WCM solution AxCMS.net 10, which streamlines the processes involved in creating, managing and distributing corporate content on the internet. The new solution helps reducing ongoing costs for managing and distributing to large audiences, while at the same time drastically reducing time-to-market and one-time setup costs. http://www.AxCMS.net Axinom’s WCM portfolio, based on the Microsoft .NET Framework 4, Microsoft Visual Studio 2010 and Microsoft Silverlight 4, allows enterprises to increase process efficiency, reduce operating costs and more effectively manage delivery of rich media assets on the Web and mobile devices. Axinom solutions are widely used by major European online brands in IT, telco, retail, media and entertainment industries such as Siemens, American Express, Microsoft Corp., ZDF, Pro7Sat1 Media, and Deutsche Post. Brand New User Interface built with Silverlight 4By using Silverlight 4, Axinom’s team created a new user interface for AxCMS.net 10 that is optimized for improved usability and speed. WYSIWYG mode, integrated image editor, extended list views, and detail views of objects allow a substantial acceleration of typical editor tasks. Axinom’s team worked with Silverlight Rough Cut Editor for video management and Silverlight Analytics Framework for extended reporting to complete the wide range of capabilities included in the new release. “Axinom’s release of AxCMS.net 10 enables developers to take advantage of the latest features in Silverlight 4,” said Brian Goldfarb, director of the developer platform group at Microsoft Corp. “Microsoft is excited about the opportunity this creates for Web developers to streamline the creating, managing and distributing of online corporate content using AxCMS.net 10 and Silverlight.” Rapid Web Development with Visual Studio 2010AxCMS.net 10 is extended by additional products that enable developers to get productive quickly and help solve typical customer scenarios. AxCMS.net template projects come with documented source code that help kick-start projects and learn best practices in all aspects of Web application development. AxCMS.net overcomes many hard-to-solve technical obstacles in an out-of-the-box manner by providing a set of ready-to-use vertical solutions such as corporate Web site, Web shop, Web campaign management, email marketing, multi-channel distribution, management of rich Internet applications, and Web business intelligence. Extended Multi-Site ManagementAxCMS.net has been supporting the management of an unlimited number of Web sites for a long time. The new version 10 of AxCMS.net will further improve multi-site management and provide features to editors and developers that will simplify and accelerate multi-site and multi-language management. Extended publication workflow will take into account additional dependencies of dynamic objects, pages, and documents. “The customer requests evolved from static html pages to dynamic Web applications content with the emergence of rich media assets seamlessly combined across many channels including Web, mobile and IPTV. With the.NET Framework 4 and Silverlight 4, we’re on the fast track to making the three screen strategy a reality for our customers,” said Damir Tomicic, CEO of Axinom Group. “Our customers enjoy substantial competitive advantages of using latest Microsoft technologies. We have a long-standing, relationship with Microsoft and are committed to continued development using Microsoft tools and technologies to deliver innovative Web solutions in the future.”  

    Read the article

  • Preview of MSDN Library Changes

    - by ScottGu
    The MSDN team has been working some potential changes to the online MSDN Library designed to help streamline the navigation experience and make it easier to find the .NET Framework information you need. To solicit feedback on the proposed changes while they are still in development, they’ve posted a preview version of some proposed changes to a new MSDN Library Preview site which you can check out.  They’ve also created a survey that leads you through the ideas and asks for your opinions on some of the changes.  We’d very much like to have as many people as possible people take the survey and give us feedback. Quick Preview of Some of the Changes Below are some examples of a few of the changes being proposed: Streamlined .NET Namespaces Navigation The current MSDN Class Library lists all .NET namespaces in a flat-namespace (sorted alphabetically): Two downsides of the above approach are: Some of the least-used namespaces are listed first (like Microsoft.Aspnet.Snapin and Microsoft.Build.BuildEngine) All sub-namespaces are listed, which makes the list a little overwhelming, and page-load times to be slow The new MSDN Library Preview Site now lists “System” namespaces first (since those are the most used), and the home-page lists just top-level namespace groups – which makes it easier to find things, and enables the page to load faster:   Class overview and members pages merged into a single topic about each class Previously you had to navigate to several different pages to find member information about types: Links to these are still available in the MSDN Library Preview Site TOC – but the members are also now listed on the overview page, which makes it easy to quickly find everything in one place: Commonly used things are nearer the top of the page One of the other usability improvements with the new MSDN Library Preview Site is that common elements like “Code Examples” and “Inheritance Hierarchy” (for classes) are now listed near the top of the help page – making them easy to quickly find: Give Us Feedback with a Survey Above are just a few of the changes made with the new MSDN preview site – there are many other changes also rolled into it.  The MSDN team is doing usability studies on the new layout and navigation right now, and would very much like feedback on it. If you have 15 minutes and want to help vote on which of these ideas makes it into the production MSDN site, please visit this survey before June 30, play with the changes a bit, and let the MSDN team know what you think. Important Note: the MSDN preview site is not a fully functional version of MSDN – it’s really only there to preview the new ideas themselves, so please don’t expect it to be integrated with the rest of MSDN, with search, etc.  Once the MSDN team gets feedback on some of the changes being proposed they will roll them into the live site for everyone to use. Hope this helps, Scott

    Read the article

  • WLS MBeans

    - by Jani Rautiainen
    WLS provides a set of Managed Beans (MBeans) to configure, monitor and manage WLS resources. We can use the WLS MBeans to automate some of the tasks related to the configuration and maintenance of the WLS instance. The MBeans can be accessed a number of ways; using various UIs and programmatically using Java or WLST Python scripts.For customization development we can use the features to e.g. manage the deployed customization in MDS, control logging levels, automate deployment of dependent libraries etc. This article is an introduction on how to access and use the WLS MBeans. The goal is to illustrate the various access methods in a single article; the details of the features are left to the linked documentation.This article covers Windows based environment, steps for Linux would be similar however there would be some differences e.g. on how the file paths are defined. MBeansThe WLS MBeans can be categorized to runtime and configuration MBeans.The Runtime MBeans can be used to access the runtime information about the server and its resources. The data from runtime beans is only available while the server is running. The runtime beans can be used to e.g. check the state of the server or deployment.The Configuration MBeans contain information about the configuration of servers and resources. The configuration of the domain is stored in the config.xml file and the configuration MBeans can be used to access and modify the configuration data. For more information on the WLS MBeans refer to: Understanding WebLogic Server MBeans WLS MBean reference Java Management Extensions (JMX)We can use JMX APIs to access the WLS MBeans. This allows us to create Java programs to configure, monitor, and manage WLS resources. In order to use the WLS MBeans we need to add the following library into the class-path: WL_HOME\lib\wljmxclient.jar Connecting to a WLS MBean server The WLS MBeans are contained in a Mbean server, depending on the requirement we can connect to (MBean Server / JNDI Name): Domain Runtime MBean Server weblogic.management.mbeanservers.domainruntime Runtime MBean Server weblogic.management.mbeanservers.runtime Edit MBean Server weblogic.management.mbeanservers.edit To connect to the WLS MBean server first we need to create a map containing the credentials; Hashtable<String, String> param = new Hashtable<String, String>(); param.put(Context.SECURITY_PRINCIPAL, "weblogic");        param.put(Context.SECURITY_CREDENTIALS, "weblogic1");        param.put(JMXConnectorFactory.PROTOCOL_PROVIDER_PACKAGES, "weblogic.management.remote"); These define the user, password and package containing the protocol. Next we create the connection: JMXServiceURL serviceURL =     new JMXServiceURL("t3","127.0.0.1",7101,     "/jndi/weblogic.management.mbeanservers.domainruntime"); JMXConnector connector = JMXConnectorFactory.connect(serviceURL, param); MBeanServerConnection connection = connector.getMBeanServerConnection(); With the connection we can now access the MBeans for the WLS instance. For a complete example see Appendix A of this post. For more details refer to Accessing WebLogic Server MBeans with JMX Accessing WLS MBeans The WLS MBeans are structured hierarchically; in order to access content we need to know the path to the MBean we are interested in. The MBean is accessed using “MBeanServerConnection. getAttribute” API.  WLS provides entry points to the hierarchy allowing us to navigate all the WLS MBeans in the hierarchy (MBean Server / JMX object name): Domain Runtime MBean Server com.bea:Name=DomainRuntimeService,Type=weblogic.management.mbeanservers.domainruntime.DomainRuntimeServiceMBean Runtime MBean Servers com.bea:Name=RuntimeService,Type=weblogic.management.mbeanservers.runtime.RuntimeServiceMBean Edit MBean Server com.bea:Name=EditService,Type=weblogic.management.mbeanservers.edit.EditServiceMBean For example we can access the Domain Runtime MBean using: ObjectName service = new ObjectName( "com.bea:Name=DomainRuntimeService," + "Type=weblogic.management.mbeanservers.domainruntime.DomainRuntimeServiceMBean"); Same syntax works for any “child” WLS MBeans e.g. to find out all application deployments we can: ObjectName domainConfig = (ObjectName)connection.getAttribute(service,"DomainConfiguration"); ObjectName[] appDeployments = (ObjectName[])connection.getAttribute(domainConfig,"AppDeployments"); Alternatively we could access the same MBean using the full syntax: ObjectName domainConfig = new ObjectName("com.bea:Location=DefaultDomain,Name=DefaultDomain,Type=Domain"); ObjectName[] appDeployments = (ObjectName[])connection.getAttribute(domainConfig,"AppDeployments"); For more details refer to Accessing WebLogic Server MBeans with JMX Invoking operations on WLS MBeans The WLS MBean operations can be invoked with MBeanServerConnection. invoke API; in the following example we query the state of “AppsLoggerService” application: ObjectName appRuntimeStateRuntime = new ObjectName("com.bea:Name=AppRuntimeStateRuntime,Type=AppRuntimeStateRuntime"); Object[] parameters = { "AppsLoggerService", "DefaultServer" }; String[] signature = { "java.lang.String", "java.lang.String" }; String result = (String)connection.invoke(appRuntimeStateRuntime,"getCurrentState",parameters, signature); The result returned should be "STATE_ACTIVE" assuming the "AppsLoggerService" application is up and running. WebLogic Scripting Tool (WLST) The WebLogic Scripting Tool (WLST) is a command-line scripting environment that we can access the same WLS MBeans. The tool is located under: $MW_HOME\oracle_common\common\bin\wlst.bat Do note that there are several instances of the wlst script under the $MW_HOME, each of them works, however the commands available vary, so we want to use the one under “oracle_common”. The tool is started in offline mode. In offline mode we can access and manipulate the domain configuration. In online mode we can access the runtime information. We connect to the Administration Server : connect("weblogic","weblogic1", "t3://127.0.0.1:7101") In both online and offline modes we can navigate the WLS MBean using commands like "ls" to print content and "cd" to navigate between objects, for example: All the commands available can be obtained with: help('all') For details of the tool refer to WebLogic Scripting Tool and for the commands available WLST Command and Variable Reference. Also do note that the WLST tool can be invoked from Java code in Embedded Mode. Running Scripts The WLST tool allows us to automate tasks using Python scripts in Script Mode. The script can be manually created or recorded by the WLST tool. Example commands of recording a script: startRecording("c:/temp/recording.py") <commands that we want to record> stopRecording() We can run the script from WLST: execfile("c:/temp/recording.py") We can also run the script from the command line: C:\apps\Oracle\Middleware\oracle_common\common\bin\wlst.cmd c:/temp/recording.py There are various sample scripts are provided with the WLS instance. UI to Access the WLS MBeans There are various UIs through which we can access the WLS MBeans. Oracle Enterprise Manager Fusion Middleware Control Oracle WebLogic Server Administration Console Fusion Middleware Control MBean Browser In the integrated JDeveloper environment only the Oracle WebLogic Server Administration Console is available to us. For more information refer to the documentation, one noteworthy feature in the console is the ability to record WLST scripts based on the navigation. In addition to the UIs above the JConsole included in the JDK can be used to access the WLS MBeans. The JConsole needs to be started with specific parameter to force WLS objects to be used and jar files in the classpath: "C:\apps\Oracle\Middleware\jdk160_24\bin\jconsole" -J-Djava.class.path=C:\apps\Oracle\Middleware\jdk160_24\lib\jconsole.jar;C:\apps\Oracle\Middleware\jdk160_24\lib\tools.jar;C:\apps\Oracle\Middleware\wlserver_10.3\server\lib\wljmxclient.jar -J-Djmx.remote.protocol.provider.pkgs=weblogic.management.remote For more details refer to the Accessing Custom MBeans from JConsole. Summary In this article we have covered various ways we can access and use the WLS MBeans in context of integrated WLS in JDeveloper to be used for Fusion Application customization development. References Developing Custom Management Utilities With JMX for Oracle WebLogic Server Accessing WebLogic Server MBeans with JMX WebLogic Server MBean Reference WebLogic Scripting Tool WLST Command and Variable Reference Appendix A package oracle.apps.test; import java.io.IOException;import java.net.MalformedURLException;import java.util.Hashtable;import javax.management.MBeanServerConnection;import javax.management.MalformedObjectNameException;import javax.management.ObjectName;import javax.management.remote.JMXConnector;import javax.management.remote.JMXConnectorFactory;import javax.management.remote.JMXServiceURL;import javax.naming.Context;/** * This class contains simple examples on how to access WLS MBeans using JMX. */public class BlogExample {    /**     * Connection to the WLS MBeans     */    private MBeanServerConnection connection;    /**     * Constructor that takes in the connection information for the      * domain and obtains the resources from WLS MBeans using JMX.     * @param hostName host name to connect to for the WLS server     * @param port port to connect to for the WLS server     * @param userName user name to connect to for the WLS server     * @param password password to connect to for the WLS server     */    public BlogExample(String hostName, String port, String userName,                       String password) {        super();        try {            initConnection(hostName, port, userName, password);        } catch (Exception e) {            throw new RuntimeException("Unable to connect to the domain " +                                       hostName + ":" + port);        }    }    /**     * Default constructor.     * Tries to create connection with default values. Runtime exception will be     * thrown if the default values are not used in the local instance.     */    public BlogExample() {        this("127.0.0.1", "7101", "weblogic", "weblogic1");    }    /**     * Initializes the JMX connection to the WLS Beans     * @param hostName host name to connect to for the WLS server     * @param port port to connect to for the WLS server     * @param userName user name to connect to for the WLS server     * @param password password to connect to for the WLS server     * @throws IOException error connecting to the WLS MBeans     * @throws MalformedURLException error connecting to the WLS MBeans     * @throws MalformedObjectNameException error connecting to the WLS MBeans     */    private void initConnection(String hostName, String port, String userName,                                String password)                                 throws IOException, MalformedURLException,                                        MalformedObjectNameException {        String protocol = "t3";        String jndiroot = "/jndi/";        String mserver = "weblogic.management.mbeanservers.domainruntime";        JMXServiceURL serviceURL =            new JMXServiceURL(protocol, hostName, Integer.valueOf(port),                              jndiroot + mserver);        Hashtable<String, String> h = new Hashtable<String, String>();        h.put(Context.SECURITY_PRINCIPAL, userName);        h.put(Context.SECURITY_CREDENTIALS, password);        h.put(JMXConnectorFactory.PROTOCOL_PROVIDER_PACKAGES,              "weblogic.management.remote");        JMXConnector connector = JMXConnectorFactory.connect(serviceURL, h);        connection = connector.getMBeanServerConnection();    }    /**     * Main method used to invoke the logic for testing     * @param args arguments passed to the program     */    public static void main(String[] args) {        BlogExample blogExample = new BlogExample();        blogExample.testEntryPoint();        blogExample.testDirectAccess();        blogExample.testInvokeOperation();    }    /**     * Example of using an entry point to navigate the WLS MBean hierarchy.     */    public void testEntryPoint() {        try {            System.out.println("testEntryPoint");            ObjectName service =             new ObjectName("com.bea:Name=DomainRuntimeService,Type=" +"weblogic.management.mbeanservers.domainruntime.DomainRuntimeServiceMBean");            ObjectName domainConfig =                (ObjectName)connection.getAttribute(service,                                                    "DomainConfiguration");            ObjectName[] appDeployments =                (ObjectName[])connection.getAttribute(domainConfig,                                                      "AppDeployments");            for (ObjectName appDeployment : appDeployments) {                String resourceIdentifier =                    (String)connection.getAttribute(appDeployment,                                                    "SourcePath");                System.out.println(resourceIdentifier);            }        } catch (Exception e) {            throw new RuntimeException(e);        }    }    /**     * Example of accessing WLS MBean directly with a full reference.     * This does the same thing as testEntryPoint in slightly difference way.     */    public void testDirectAccess() {        try {            System.out.println("testDirectAccess");            ObjectName appDeployment =                new ObjectName("com.bea:Location=DefaultDomain,"+                               "Name=AppsLoggerService,Type=AppDeployment");            String resourceIdentifier =                (String)connection.getAttribute(appDeployment, "SourcePath");            System.out.println(resourceIdentifier);        } catch (Exception e) {            throw new RuntimeException(e);        }    }    /**     * Example of invoking operation on a WLS MBean.     */    public void testInvokeOperation() {        try {            System.out.println("testInvokeOperation");            ObjectName appRuntimeStateRuntime =                new ObjectName("com.bea:Name=AppRuntimeStateRuntime,"+                               "Type=AppRuntimeStateRuntime");            String identifier = "AppsLoggerService";            String serverName = "DefaultServer";            Object[] parameters = { identifier, serverName };            String[] signature = { "java.lang.String", "java.lang.String" };            String result =                (String)connection.invoke(appRuntimeStateRuntime, "getCurrentState",                                          parameters, signature);            System.out.println("State of " + identifier + " = " + result);        } catch (Exception e) {            throw new RuntimeException(e);        }    }}

    Read the article

  • links for 2010-04-28

    - by Bob Rhubart
    Guido Schmutz: Oracle BPM11g available! Oracle ACE Director Guido Schmutz shares his impressions after attending a hands-on workshop conducted by Masons of SOA member Clemens Utschig-Utschig. (tags: oracle otn oracleace bpm soa soasuite) Elena Zannoni : 2010 Collaboration Summit Impressions Elena Zannoni has collected her thoughts on #C10 and shares them in this great blog post. (tags: oracle otn linux architecture collaborate2010) Hajo Normann: BPMN 2.0 in Oracle BPM Suite: The future of BPM starts now "The BPM Studio sets itself apart from pure play BPMN 2.0 tools by being seamlessly integrated inside a holistic SOA / BPM toolset: BPMN models are placed in SCA-Composites in SOA Suite 11g. This allows to abstract away the complexities of SOA integration aspects from business process aspects. For UIs in BPMN tasks, you have the richness of ADF 11g based Frontends." -- Oracle ACE Director and Masons of SOA member Hajo Normann (tags: oracle otn oracleace bpm soa sca) Brain Dirking: AIIM Best Practice Awards to Two Oracle Customers Brian Dirking's great write-up of the AIIM Awards Banquet, at which the Bureau of Indian Affairs and the Charles Town Police Department were among the winners of the 2010 Carl E. Nelson Best Practices Awards. (tags: oracle otn aiim bpm ecm enterprise2.0) Mark Wilcox: Upcoming Directory Services Live Webcast - Improve Time-to-Market and Reduce Cost with Oracle Directory Services Live Webcast: Improve Time-to-Market and Reduce Cost with Oracle Directory Services Event Date: Thursday, May 27, 2010 Event Time: 10:00 AM Pacific Standard Time / 1:00 Eastern Standard Time (tags: oracle otn webcast security identitymanagement) Celine Beck: Introducing AutoVue Document Print Service Celine Beck offers a detailed overview of Oracle AutoVue. (tags: oracle otn enatarch visualization printing) Vikas Jain: What's new in OWSM 11gR1 PS2 (11.1.1.3.0) ? Vikas Jain shares links to resources relevant to the recently releases patch set for Oracle Web Services Manager 11gR1. (tags: oracle otn soa webservices oswm) @theovanarem: Oracle SOA Suite 11g Release 1 Patch Set 2 Theo Van Arem shares links to several resources relevant to the release of the latest patch set for Oracle SOA Suite 11g. (tags: oracle otn soa soasuite middleware) @vambenepe: Analyzing the VMforce announcement "The new thing is that force.com now supports an additional runtime, in addition to Apex. That new runtime uses the Java language, with the constraint that it is used via the Spring framework. Which is familiar territory to many developers. That’s it." -- William Vambenepe (tags: oracle otn cloud paas)

    Read the article

< Previous Page | 263 264 265 266 267 268 269 270 271 272 273 274  | Next Page >