Search Results

Search found 10397 results on 416 pages for 'mobile devices'.

Page 267/416 | < Previous Page | 263 264 265 266 267 268 269 270 271 272 273 274  | Next Page >

• What happens when the USB key or SD card I've installed VMware ESXi on fails?

  - by ewwhite

  An SD (SDHC) card installed in an HP ProLiant DL380p Gen8 server running VMware ESXi just failed. I encountered some rather ominous looking messages on the vCenter console and in the HP ProLiant ILO event log... Lost connectivity to the device ... backing the boot filesystem. As a result, host configuration changes will not be saved to persistent storage. Embedded Flash/SD-CARD: Error writing media 0, physical block 848880: Stack Exception. VMware advocates the use of USB and SD (SDHC) boot devices for ESXi. It was one of the main reasons the smaller footprint ESXi was developed (versus the older ESX). I've spent much time highlighting the differences between ESXi's installable and embedded modes to coworkers and clients. However, these failures do seem to happen. In this case, this is my third instance. Luckily, this is a vSphere cluster with SAN storage. What steps should be taken to remediate this failure?

  Read the article

• How to stop intermittent playback on airtunes (iTunes + Airport Express)?

  - by Alex B

  Is there a definitive answer for how to stop intermittent "skips" or pauses while playing music from iTunes to an airport express connected to my home stereo? When I read other forums I see a wealth of posts that say "I did XYZ and it's fixed" followed by "I tried XYZ and it didn't work." This does not appear to be signal strength related. The green light on the Airport Express does not turn to yellow/orange. Other wireless devices have no trouble connecting at the same or greater distances from the wireless router.

  Read the article

• How to log the actual output in apache?

  - by Oscar Rodriguez

  I am doing LAMP development for a mobile platform. However, the client browser does not allow me to view the source code of visited pages. I consider the source code to be of huge importance for debugging, so I would like to configure my web server so every time a user makes a request, in addition to sending the client a response, that response (the actual contents of the returned page) is also stored in a file with a filename I can cross-relate with access_log (maybe ip-timestamp-filename? or maybe a unique ID in an additional column in access_log?). I've searched quite a bit, but haven't even gotten close to finding what I'm looking for. Has anybody been able to do this?

  Read the article

• Recover lost NTFS partition on SSD

  - by Emil

  Hello, About 2 month ago I upgraded my Dell Latitude E6500 laptop with a Corsair Force F120 SSD drive. Everything worked well until about a week or so back. I started the computer and was faced with a beep and a message saying "No boot sector on Internal HDD (IRRT). No bootable devices". Since I figured that the boot sector had somehow got corrupt I tried booting from the Windows 7 dvd in order to repair the boot sector. But the Windows 7 installation program only found a blank drive with 111GB of unallocated space. I panicked and brought the drive with me to work to let a colleague have a look at it. We made a disk image of the entire drive and ran the drive through Testdisk in Linux. Testdisk did not find any partitions. It appears that the drive has been completely erased... What has happened? What is causing this behavior on an SSD?

  Read the article

• Corporate Wiki Organization - Technical Documentation

  - by Dave Jarvis

  Corporations have documents describing various aspects of their technical systems, including: Custom Applications Custom Development Frameworks Third Party Applications Accounting Bug Tracking Network Management How To Guides User Manuals Web Browsers Software Tools Development IDEs Graphics GIMP xv Text Editing File Transfer ncFTP WinSCP Hardware Servers Web Database Exchange File Network Devices Printers Drawings If you had to use a Wiki to manage the documentation, what other items would you add to the list, and how would you organize it? (For example, would Software Tools make more sense under Third Party Applications?) A few constraints: The structure should not go beyond three levels deep. Avoid the word "and" in favour of two different categories. Keep the structure general: it should appy as broadly as possible. Target audience is primarily technical, but could be visible by anyone.

  Read the article

• What is the minimum power supply wattage needed for a Pentium 2.4GHz system?

  - by scottmarlowe

  It looks like I've got a dead Antec True 330 power supply in an older desktop that has an Intel D845PESV motherboard, a Pentium 2.4GHz processor, 2 dvd/cd writers, 2 hard drives, and other typical devices. I have an even older computer that is not being used that has a 200W power supply. Can a 200W power supply drive what I've listed above? Or, put another way, what is the minimum power supply specs for the above system? (A new 350W power supply will run me $30--so buying a new one is not a problem--but I'm curious about the question nonetheless).

  Read the article

• Changing privilege rights on Arch Linux for a particular program

  - by sherrellbc

  I am quite new to linux and have had issues surrounding every program that I install. Basically, anything that is placed outside of my home directory requires a sudo call prior to opening/executing. I cannot write to files, open usb devices, or run programs that exist outside of this directory (specifically, above this directory). I know this is a privilege problem, but I come here to ask how this can be permanently stopped. How can I configure things such that when programs are installed I do not have to manually find the executable and change its privilege requirements?

  Read the article

• Sony Vaio: Bluetooth problem

  - by Mehper C. Palavuzlar

  I have a Vaio VPCCW21FX with Windows 7 Home Premium. I'm trying to reach the bluetooth settings but to no avail. I could neither switch the bluetooth on nor find the settings for it. I have tried the following: In Start menu, typed bluetooth, found "Bluetooth" in Programs, clicked on it, but there was no response. Checked task manager, there's nothing related bluetooth. Headed for Control Panel, opened Add Devices or Printers, right-clicked on Vaio computer, clicked on Bluetooth Settings, and no response again. What's wrong with my laptop? How can I fix this?

  Read the article

• Monitoring Bandwidth Usage (Per Internal IP) - Cisco ASA 5505

  - by Joseph Sturtevant

  I manage a small network with a Cisco ASA 5505 and a shared DSL connection. I would like to be able monitor the bandwidth usage of the various users/devices on my network (by IP). Can I do that using the ASA? Has anyone got this working? What is the best way to do this? Some Ideas I Have Seen Online: SNMP with a tool like Cacti Does this give per IP usage with an ASA or just overall usage? Netflow with a tool like ntop Couldn't get this to work. It seems that the Netflows sent by ASA are not exactly standard. Ntop receives them, but doesn't seem to know what do with them.

  Read the article

• How yo set up a Sony Vaio PCG-4121EM 3G modem?

  - by Ivan

  We've bought a Sony Vaio PCG-4121EM supposed to have a built-in 3G modem. It has a SIM-card slot at its bottom. We've inserted a newly-bought SIM-card but nothing happened and the modem is still not visible among the computer devices (neither in Windows device manager nor in "Modems" Control Panel applet). How to turn it on? I would usually seek to turn a built-in device in the BIOS setup, but there seem to be no BIOS setup on this Vaio - Windows 7 splash screen appears immediately as I turn the computer on.

  Read the article

• Atheros LAN card driver, Linux compiling problem

  - by Ali Qocayev

  I have installed openSUSE 11.4 to my new workstation. It says that there is Attansic ETHERNET controller on board. But no devices seen. I typed: lspci and it returned: atheros communications device 1083. I have downloaded drivers. I'm trying to compile the driver. But I get the error: **Makefile:94: Linux kernel source not configured - missing autoconf.h. Stop** But I see autoconf.h presents on my system. What should I do ?

  Read the article

• Using the Juniper EX3300 Switch as a router?

  - by Richard Whitman

  I have a Juniper EX3300 switch in a data center. And I have connected one of the uplink ports (ge-0/1/0) to my ISP's router. I want to configure it so that all the devices connected to ports in the same VLAN as ge-0/1/0 can access the Internet. I have done some research, and I haven't gotten anywhere really. I have configured the interface as follows: ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family inet { address xx.xx.xx.xx/32; } } } where xx.xx.xx.xx is the "Customer Router Port IP" assigned by my ISP. When I try to commit, I get the following error: Interface ge-0/1/0.0 not enabled for switching Can some one tell me what is the right way to configure it?

  Read the article

• Effects of HTTP/TCP connection handshakes and server performance

  - by Blankman

  When running apache bench on the same server as the website like: ab -n 1000 -c 10 localhost:8080/ I am most probably not getting accurate results when compared to users hitting the server from various locations. I'm trying to understand how or rather why this will effect real world performance since a user in china will have different latency issues when compared to someone in the same state/country. Say my web server has a maximum thread limit of 100. Can someone explain in detail how end user latency can/will effect server performance. I'm assuming here that each request will be computed equally at say 10ms. What I'm not understand is how external factors can effect overal server performance, specifically internet connections (location, or even device like mobile) and http/tcp handshakes etc.

  Read the article

• HP ProCurve GVRP Setup

  - by Matt

  I'm trying to setup GVRP on my 4 ProCurve switches. Currently I have a Layer 3 3500yl-24G (J8692A) which is connected to 3 Layer 2 2510G-48 (J9280A). I have three trunk ports setup on the 3500 connected to the 3 switches and currently everything seems to be working, the devices are talking to eachother and GVRP is pushing its configurations from the 3500 to the 3 other switches. My question is, once GVRP is setup, how exactly do I configure the ports on the 3 L2 switches to use the correct VLAN? I'm new to ProCurve network equipment and this is much easier to setup on Cisco equipment.

  Read the article

• Stuck on Checking battery state at startup in Ubuntu, have splash screen no startup

  - by jeffhsu3

  I am running Ubuntu 10.04 LTS. When I boot up the computer it goes to the splash but there is no login screen, just the purple background and the mouse cursor. "Checking battery state" is the last line that does not have an "[OK]". When I press Ctr-alt-shift-F1 I can login and sudo stop gdm and startx. However this makes it so that the applets don't show. Error: "The panel encountered a problem while loading "OAFIID:GNOME_notificationAreaApplet" and does it for every single applet. Everything else works fine though. I get a EHCI: BIOS handoff failed twice in the dmesg as well. The laptop has intel mobile integrated graphics. UPDATE: Now my desktop has the exact same problem. Things that I have tried: Changing to GRUB_CMDLINE_LINUX_DEFAULT="i915.modeset=1 acpi=off"

  Read the article

• Can single ESXi host make use of two separete iSCSI box?

  - by user71061

  Hi! I have problem with using multiply iSCSI targets with single ESXi host (in my case they are two FreeNAS hosts, but I suspect that this problem will occur with any two iSCSI box of that same type/model). If I configure two FreeNAS hosts as iSCSI targets (say iSCSI A and iSCSI B), then I can use both of them with my ESXi host, but only one at a time (i.e only iSCSI A or only iSCSI B, but not both of them simultaneously). If I try to add second iSCSI target to my iSCSI adapter (of course it has unique iqn name), then in a details pane of this adapter (it is iSCSI software adapter), I see that total number of paths has increased accordingly, but not total number of devices (so I can't use it as another storage). What should I do? It is impossible to attach two iSCSI targets to single adapter? I'm using free version of ESXi 4.1. Maybe it is an limitation of free version? Thanks in advance for any sugestion.

  Read the article

• LSI RAID-on-chip with RAID6 over two SAS links goes red when HDD enclosure is powered cycled; how to recover?

  - by GregC

  I have a RAID6 array managed by LSI 9286-8e card. I also have Sans Digital 24-bay NexentaSTOR JBOD enclosure with SAS extender built-in. They are connected to separate UPS devices. Normally, I'd shut down the PC, leaving RAID6 in healthy state. But today the power to JBOD enclosure was cut but PC kept running. After restarting the PC, all disks in RAID6 have lit up RED, and the only option in LSI MegaRAID manager app was to reset each disk to unassigned, thereby loosing all data on RAID6 array. Thankfully, I am only testing, but how would I recover if this were to happen in production?

  Read the article

• Don't know why this small shell script wont work

  - by tominated

  Hi, I'm trying to make a small script to start up gunicorn for a python website I'm making. I have modified the script found at https://github.com/benoitc/gunicorn/blob/master/examples/gunicorn_rc slightly. Here's my version. #!/bin/sh GUNICORN=/usr/local/bin/gunicorn ROOT=/srv/mobile-site/app PID=/var/run/gunicorn.pid APP=mobilecms:app if [ -f $PID ]; then rm $PID fi cd $ROOT exec $GUNICORN -b 127.0.0.1:8080 -w 8 -k gevent --pidfile=$PID $APP When I try to run the script though, it shows this error /etc/init.d/gunicorn: 13: Syntax error: end of file unexpected (expecting "fi") Does anyone know what's wrong?

  Read the article

• Remote control a computer using another computer

  - by Dean

  I've got a main desktop computer at home, I'd like watch movies using it but able to control it afar. For example, I would like to lay on my bed and control the desktop using my own laptop via wireless. I've been looking for solutions to my question. I tried to use remote desktop, I can pause the movie but I then have to go to the pc to log in the OS again. I also tried to bind my desktop to my mobile phone over bluetooth, this works as I can control the mouse etc. but I found I can barely see the mouse pointer when at long distance. I still wish I can use my laptop as a remote control, is this possible?

  Read the article

• What does "Local Domain Name" on router do and how do I get it to work?

  - by Giovanni Galbo

  I have a D-Link DGL-4500 router. One of the settings is "Local Domain Name," which I have set to local (see screenshot). What I expect is for me to be able to hit my computers via name, e.g. m6.local should resolve to one of my computers; but this isn't happening. I know that I can do this via hosts file, but it would be neat if I could do it via the router... plus I have devices like an iPad that don't let you edit the hosts file. Am I misunderstanding this router feature or am I doing something wrong?

  Read the article

• CORAID using only 1 of the 2 available NICs for AoE traffic

  - by Peter Carrero

  We got 6 CORAID shelves in my workplace. On 2 of them I see AoE traffic on only 1 of the 2 NICs that are attached to the SAN switch. We got jumbo frames enabled on all devices. Both NICs show up when I issue the aoe-interfaces command. This wouldn't bother me too much if the throughput performance observed on the "bad" shelves using bonnie++ wasn't half of the result of the "good" shelves. The "good" shelves are older SR1521 model and they have ReiserFS on their LUNS - not that I think it makes a difference - and the "bad" shelves are newer SR2421 model and have JFS. Any help as to what is going on and how to rectify this would be greatly appreciated. BTW: even the lower performing shelves outperform another iSCSI device we got, but that is another story... Thanks.

  Read the article

• SpinRite and USB blues - does a solution exist?

  - by Peter Mortensen

  I use SpinRite to recover hard disks and their content, and to a lesser degree for preventive maintenance. However, if a USB drive (USB thumb drive and/or external hard disk with a USB interface) is connected when SpinRite scans for devices, then SpinRite never finishes/hangs. The work-around is of course to disconnect the drive, but there is value in being able to use SpinRite on USB drives. Some external drives have no screws and it is difficult to take out the hard disk without damaging the casing. And for those that have it would save the disassembling time. Is there a way to fix this problem (e.g. BIOS changes or a modified SpinRite boot CD) without resorting to floppy disks?

  Read the article

• Converting Future Composer FC14 tracker music to MIDI data

  - by okw

  I have an old .FC music file from the Amiga/C64 days. It was made using Future Composer. The first four bytes of the file read as FC14 in ASCII; I'm pretty sure that's the version number. I need to dump the channels and their notes into a standard MIDI file in order to play it through my MIDI devices. Is there a way to do this with existing programs? If not, are there any specifications available on the format of these files? I do not require the samples, and I am aware that they will be lost during the conversion process.

  Read the article

• Windows Server 2003 Licensing

  - by Phil

  Hi all, I'm looking to get a Windows Server 2003 box in the middle of my linux network. :( I'm just concerned about CAL licensing for it. No devices will access any network server function of Windows Server 2003. I don't need Windows for DHCP or DNS or file and print sharing. I have linux boxes to do that! xD I just need a box running Windows (of some variety) to host those few apps that have to run on Windows like my AV management console. In short do I need any CALs for my server if its not acting as server itself. I think Windows Server 2003 comes with 5 CALs which can be per user for the admins to use RDP? Thanks, Phil

  Read the article

• Can't boot from SATA dvd, seen as SerialCH1_Master

  - by dierre

  Here's the problem: I have an old computer based on an AsRock motherbord, the p4vt8+. I have 2 IDE HDs , one per each channel (IDE0 and IDE1) and I have a SATA dvd LG GH22N550. When I go into the BIOS panel on the boot devices list I can see IDE0 and IDE1 but not the dvd that I need to install Windows. When the computer is booting I can see it under the voice SerialCH1_Master. I know I'm doing something wrong but I can't figure out what it is.

  Read the article

< Previous Page | 263 264 265 266 267 268 269 270 271 272 273 274  | Next Page >