Search Results

Search found 17063 results on 683 pages for 'frank computer'.

Page 268/683 | < Previous Page | 264 265 266 267 268 269 270 271 272 273 274 275  | Next Page >

• Hard drives (SATA/ATA) corrupting

  - by JC Denton

  Hello All, 2 years ago I bought relatives a new computer for christmas and installed Ubuntu on it. Ever since then it has been experiencing problems with the hard drives. The hard drive supplied with the machine was a SATA drive. When it appeared it was having problems (files and folders with invalid encoding started appearing) I replaced the SATA drive with the drive of their previous computer. I replaced it (The replacement) later on, the drive being rather old and thus becoming more prone to the risk of failure. The replacement drive is a IDE drive but the same problems started to appear (files and folders showing up in nautilus with invalid encoding). I fear the files and folders that are showing are existing FS entries, starting to corrupt. As it's happening to both the IDE and SATA drive it's unlikely to be the drives themselves or the IDE/SATA controller, I believe. Any ideas as to what could be causing the (assumed) corruption? EDIT: You're right about the paragraphs. They were there in edit mode but I'm still getting to grips with the whitespace format codes. The system is a "Primo Pro" AMD Phenom II X4 Quad Core 920 2.80GHz SILENT DDR2, ordered from overclockers.co.uk and nothing has been added to it except for the replacement of the SATA drive with an AMD drive. It would seem unlikely for a barebones system to be underpowered.

  Read the article

• Windows xp recovery console without Ntfs.sys? (0x00000024 BSOD)

  - by Kalle

  I have two physical disks in a computer, for simlicity lets call them C and D. C: got Windows XP and D: got some data. The problem is that whenever i have D: connected i can't boot windows. I get some BSOD called 0x00000024/NTFS_FILE_SYSTEM. Same thing if i boot up windows with D: disconnected and then connect it once windows has loaded. The KB article about this problem says that i have to run chkdsk but i can't get to somewhere where i can run this because i get a BSOD whenever the disk is connected! Even the recovery-console BSODs if D: is connected. The final option in the KB is to boot the computer on Windows 2000 Setup disks where you edit some file to manually disable the ntfs.sys driver and then run chkdsk. The problem is that i don't have any floppy drive. Is there any way to boot the built in recovery console with ntfs.sys disabled or to burn the floppy version to a cd after you've extracted and modified it on the harddrive? Right now the Windows xp bootable floppy creator(2) is asking me which floppy drive to extract to which i can't answer because i have none :/ Other solutions to the root problem is also appreciated :) (2) ht tp://www.microsoft.com/downloads/details.aspx?FamilyID=55820edb-5039-4955-bcb7-4fed408ea73f&displaylang=en

  Read the article

• Remote Desktop Network Level Authentication Not Supported

  - by Iszi

  I'm running Windows XP Professional SP3 x86, trying to connect to a system with Windows 7 Ultimate SP1 x64. Recently, I updated the Remote Desktop Connection software on the XP system in hopes of using Network Level Authentication (NLA) for my connections to the Windows 7 box. After the update, I connected to the Windows 7 box over RDP and enabled NLA believing that the updated client should support it. After disconnecting and attempting to reconnect, I'm presented with the following error: The remote computer requires Network Level Authentication, which your computer does not support. For assistance, contact your system administrator or technical support. So, I checked the About page in Remote Desktop Connection to make sure the update had applied. This is what I see. Remote Desktop Connection Shell Version 6.1.7600 Control Version 6.1.7600 © 2007 Microsoft Corporation. All rights reserved. Network Level Authentication not supported. Remote Desktop Protocol 7.0 supported. I thought NLA was supposed to be a part of RDP 7.0 clients. Is there a component I'm missing somewhere?

  Read the article

• How to force a login for an administrator when using Remote Desktop Connection and fast user switching enabled?

  - by brett rogers

  Scenario: I am at work. I want to remote desktop into my machine at home. Problem is, my 5-year-old daughter is playing games on Starfall.com (or something similar) on her (non-admin) account. When I attempt to connect I see this message: Another user is currently logged on to this computer. If you continue, this user has to disconnect from this computer. Do you want to continue? I click Yes and then see Please wait for 'UserName' to respond This presents my daughter with an Allow/Disallow dialog on whether to let me connect. She clicks Disallow (or No or whatever it says) and then I see 'UserName' has denied your request Question: How can I force my account to log in and disconnect her session? Additional Info: My account is an administrator account. My daughter's account is a non-administrator account. Home machine is Windows 7 Pro with fast user switching enabled. Turning off fast user switching is not an option (Kyle pointed out in his answer that turning it off would allow the admin to force another user off). I would keep fast user switching's ability to change accounts without closing the previous account's session over being able to force myself to connect.

  Read the article

• Ubuntu 13.04 to 13.10: Filesystem check or mount failed [migrated]

  - by SamHuckaby

  I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

  Read the article

• Where do I define a group policy that will set a users desktop background color to green the first time they log in?

  - by Tyler

  Servers: W2k8 R2 x64 Desktops: Win7 Pro x64 Our current group policy uses a custom ADM file to define certain properties of the desktop (Background Image (centered), Background Color is green (00 74 00)). This policy works for us, but the down-side is that policies defined in our custom ADM are only applied after a GPUpdate /Force is applied. We would like these desktop theme settings to be applied the first time the user logs onto the computer. I've been working on a new policy that forces the computer to wait for the network when the user logs on to handle folder redirection. The reason for writing the new policy was to resolve the issue that a user needs to run GPupdate /Force the first time they log in, so it doesn't make sense for me to implement the new policy if there is still something that requires GPUpdate /Force to get the user in the state that we want them. I've moved the setting for background image out into Admin Templates- Desktop- Desktop- "Desktop Wallpaper" so this is now being set properly when the user first logs in. Now I'm left with a black background until I force a group policy update. I have tried to play around with setting a default "Theme" and had limited success; this was not reliable enough to call a solution. I suppose I could set the background color with a script? Any thoughts? It feels like I'm missing something obvious, or that this should be much easier than it is.

  Read the article

• How to start using twill?

  - by brilliant

  How do I start using twill? I have just downloaded it, unpacked it and clicked on the setup .py file in the folder. The black window (terminal) appeared for a moment and vanished. (I do have Python 2.5 installed on my computer - along with SDK from Google App Engine) In the twill documentation section it says: Downloading twill The latest release of twill is twill 0.9, released Thursday, December 27th, 2007; it is available for download at http://darcs.idyll.org/~t/projects/twill-0.9.tar.gz. You can also use Python's easy_install to install or upgrade twill. twill works with Python 2.3 or later. To start using twill, install it and then type twill-sh. At the prompt type: go http://www.slashdot.org/ show showforms showhistory I am not clear from this passage what I am supposed to type (only "twill-sh" or "twill-sh" and all the words under that line) and where (I tried typing it in the command prompt window of my computer - to no avail) Can, anyone, please, help me out here? Thank You in advance.

  Read the article

• SQL Server Agent refuses to start

  - by Geo Ego

  I'm having a problem with SQL Server 2005 where the SQL Server Agent suddenly refuses to start. If I attempt to start it through Services, I get the error "SQL Server Agent (MSSQLSERVER) service on Local Computer started and then stopped." In the Application log, I have the following entry: Event Type: Error Event Source: SQLSERVERAGENT Event Category: Service Control Event ID: 103 Date: 5/20/2010 Time: 11:07:07 AM User: N/A Computer: SHAREPOINT Description: SQLServerAgent could not be started (reason: Unable to connect to server 'SHAREPOINT'; SQLServerAgent cannot start). This database has been running fine for four months. It contains a SharePoint configuration database, which two days ago stopped working, throwing me a message that the configuration database cannot be reached. It was then that I realized the SQL Server Agent was not running, and I have been unable to restart it. I have tried running it with both the local system account and the network service account, with the same results. So far, I have tried: Granting the administrators group, network service, and SharePoint SQL Server Agent account public and sysadmin roles on the database. Granting the administrators group, network service, and SharePoint SQL Server Agent account full permissions to the entire MSSQL directory and all files within. I still have no joy.

  Read the article

• Best way to 'harden' embedded ext4 file server against unexpected loss of power?

  - by Jeremy Friesner

  Hi all, First, a little background: my company makes an audio streaming device that is a headless, rack-mounted Linux box with a couple of SSDs attached. Each SSD is formatted with ext4. The users can connect to the system using Samba/CIFS to upload new audio files or access existing ones. There is also custom software for streaming out audio over the network. This is all fine. The only problem is that the users are audio people, not computer people, and see the system as a 'black box', not as a computer. Which means that at the end of the day, they aren't going to ssh in to the box and enter "/sbin/shutdown -h"; they are just going to cut power to the rack and leave, and expect things to still work properly the next day. Since ext4 has journalling, journal checksumming, etc, this mostly works. The only time it doesn't work is when someone uploads a new file via Samba and then cuts power to the system before the uploaded data has been fully flushed to the disk. In that case, they come in the next day and find that their new file has been truncated or is missing entirely, and are unhappy. My question is, what is the best way to avoid this problem? Is there a way to get smbd to call "sync" at the end of every upload? (Performance on uploads isn't so important, since they only happen occasionally). Or is there a way to tell ext4 to automatically flush within a few seconds of any change to a file? (Again, performance can be sacrificed for safety here) Should I set a particular write-ordering mode, activate barriers, etc?

  Read the article

• Is it possible to stop the "Beep" device on all computers in a Windows network?

  - by sharptooth

  On Windows the default behavior it to make an annoying "beep" sound every time Windows things something notable happened. The result is that when someone send a company-wide email via the MS Exchange all computers around my cubicle beep one by one. This is annoying and makes no sense. Luckily beeping can be shut off. Someone has to: open the "Device Manager", select "View - Show hidden devices", find the "Beep" device in "Non-Pug and Play Devices" node, open its properties, go to the "Driver" tab, set "startup type" to "Disabled" and click "Stop". The "Beep" device will stop and no longer produce the useless sound. This solution however requires tracking every computer and then talking to its user which is not very convenient. Device Manager doesn't allow stopping a device on another computer. I'm looking for a solution that can be deployed by the administrators team. We have a domain and the administrators even install the programs company-wide automatically. Are there any means to stop the "Beep" device an all computers in the Windows network with some remote-administration features automatically?

  Read the article

• Vista WHS Client stopped resolving local names

  - by andrewcr

  I’m running Windows Home Server PP2 in my home, with 3 client computers: two XP and one Vista. I have a router that provides my local DHCP and the server has a static IP address. The other day the Vista machine hung, and on reboot stopped resolving local names. It will show the green home server client icon in the system tray, but if I attempt to log in to the console, I get a “This computer cannot connect to your home server” message. If I ping the server name from the command line, it does not resolve, and gives a “could not find host” message. Oddly enough, if I browse the network, I can see the server, but double clicking on it fails. The other machines on the local network have no problems seeing the server, and the Vista machine has no problems resolving names from the internet, it just can’t see any local machines. I’m aware that I can work around this by adding entries to my HOSTS file (it does work), but I’d like this to work the way it’s “supposed” to. I’m an experienced computer user and developer, but not a networking whiz. Can anyone tell me how local name resolution is supposed to work in my environment and/or suggest ways to troubleshoot this? Thanks, Andy

  Read the article

• Choose identity from ssh-agent by file name

  - by leoluk

  Problem: I have some 20-30 ssh-agent identities. Most servers refuse authentication with Too many failed authentications, as SSH usually won't let me try 20 different keys to log in. At the moment, I am specifying the identity file for every host manually, using the IdentityFile and the IdentitiesOnly directive, so that SSH will only try one key file, which works. Unfortunately, this stops working as soon as the original keys aren't available anymore. ssh-add -l shows me the correct paths for every key file, and they match with the paths in .ssh/config, but it doesn't work. Apparently, SSH selects the indentity by public key signature and not by file name, which means that the original files have to be available so that SSH can extract the public key. There are two problems with this: it stops working as soon as I unplug the flash drive holding the keys it renders agent forwarding useless as the key files aren't available on the remote host Of course, I could extract the public keys from my identity files and store them on my computer, and on every remote computer I usually log into. This doesn't looks like a desirable solution, though. What I need is a possibility to select an identity from ssh-agent by file name, so that I can easily select the right key using .ssh/config or by passing -i /path/to/original/key, even on a remote host I SSH'd into. It would be even better if I could "nickname" the keys so that I don't even have to specify the full path.

  Read the article

• Very slow connection to xserve via afp or smb

  - by Mhoffman13

  Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

  Read the article

• Dual boot windows 8 pro and windows 7 on XPS 8500 Special Edition

  - by Jesse

  I am trying to install a dual boot with windows 7 premium and windows 8 Pro on an XPS 8500 special edition. I created a new primary partition on my C: drive, inserted the windows 8 install disk, and rebooted my computer from DVD. I select custom install and the dialog box saying "Where do you want to install windows at?" pops up but none of my drives are listed. Please help me determine what is going on. I don't understand why none of my drives are showing up on this menu. Not even the original drive. When I go to load driver and click on the partition I created it tells me "No signed device drivers were found. Make sure the installation media contains the correct drivers, and then click OK." resolved above issue by running setup from the source folder on the install disk instead of booting from DVD. Was able to locate my new partition and start install. It completes the first step of "Copying windows files" just fine but then on the next step "Getting files ready for installation" my computer restarts and attempts to load windows 8 but keeps telling me my pc needs to restart. This keeps going on in an infinite boot loop. Please help, this has been a nightmare!

  Read the article

• Cannot ping Google Public DNS on 8.8.8.8

  - by Tibor

  I have a weird problem on my Windows 7 (x64) computer. I seem to cannot ping the Google Public DNS on one of its addresses (while the other works fine). The peculiar thing is that it fails with the General failure. error message which usually means that there is a problem with a network adapter/base connectivity and not a timeout as one would expect. I checked my routing tables for any anomalies and I even flushed them but the problem seems unrelated. All the other hosts I tried ping fine (either respond or timeout). If I try to tracert or connect to the address via browser (yes, I know that it doesn't listen on port 80), it also fails instantaneously. The reason I need to ping 8.8.8.8 is that I commonly use it as a test of Internet conectivity due to it being rememberable. The problem occurs no matter where I connect to the Internet (it is a laptop computer). What could be the cause of this anomaly? Note: I use native IPv6 connectivity.

  Read the article

• Access Windows Boot Manager selector when timeout is set to 0?

  - by Kyle Cronin

  I've installed Wubi onto a Windows Vista computer. I've also set the boot timeout to 0: bcdedit /timeout 0 However, now I can't figure out how to get the menu to come up at all! I read on the internets that I had to hold F8 or space when starting up, but they doesn't seem to do anything. Is there a different key or setting I've overlooked? The computer itself is a Dell that's a few months old. The keyboard is USB, but I don't think that's the problem as I can get into the BIOS just fine. Maybe I'm doing it wrong? Am I supposed to hold the keys or rapidly tap them (I've tried both)? If it helps, here's the output from bcdedit: C:\Windows\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=C: description Windows Boot Manager locale en-US inherit {globalsettings} default {current} resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} displayorder {current} {e2484fe7-5e97-11de-84d4-0024e8074422} toolsdisplayorder {memdiag} timeout 0 resume No Windows Boot Loader ------------------- identifier {current} device partition=C: path \Windows\system32\winload.exe description Windows Vista locale en-US inherit {bootloadersettings} recoverysequence {572bcd55-ffa7-11d9-aae0-0007e994107d} recoveryenabled Yes osdevice partition=C: systemroot \Windows resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} nx OptIn Real-mode Boot Sector --------------------- identifier {e2484fe7-5e97-11de-84d4-0024e8074422} device partition=C: path \ubuntu\winboot\wubildr.mbr description Ubuntu

  Read the article

• Unix Permissions: Enable access to files no matter the user?

  - by TK Kocheran

  I've been using Linux for a long time and I still am completely in the dark about how file permissions really work. With that in mind, does anyone have any books or thorough guides I could read to really understand things completely? I've done my fair share of sysadminning, so I know the easy stuff like making directories readable and writable, making files executable, and changing the owner of a file, but on sharing files across users, I'm lost. Here's my main problem. I have a number of machines across which I intend to synchronize my music library. I've been using Unison for a while now and it's a great choice as I can easily run it over SSH on my local network which I just set up. Win-win. Up until this point, I've been synchronizing computers using a 2TB external hard drive. (computer 1 unisons to HD, computer 2 unisons to HD, etc.) This is tedious at best, especially since I encrypted the drive, making it a huge hassle to hook it up to all of my machines and sync it. Anyway, the drive is running ext4 (in TrueCrypt), so it maintains all Unix filesystem info like owners and groups. I just set up a new machine and just Unison'd it to get the music on it, and I realized that now, all of my permissions are fubar. I had to run Unison as root since that was the only way I could get the files to come off of the external drive. Apparently, since I'm using a different user name on this machine than my usual "rfkrocktk" across all machines, this essentially throws a huge wrench in the gears. Here's my use case. This laptop has two effective users, "leandra" and "rfkrocktk". I want to share music between these two users, so I symlinked /home/rfkrocktk/Music to point to /home/leandra/Music. How do I (a) allow both users access to read/write/delete files in this folder, and (b) keep everything nicely in sync without messing up file ownership?

  Read the article

• Windows XP error message: "Windows cannot find 'explorer.exe'"

  - by Meysam

  In Windows XP I can open "My Computer" and see all the hard drives. I can also see the explorer.exe process running among other processes in Task Manager. But after opening "My Computer", when I double click on one of the drives to open it, I get the following error message: Windows cannot find 'explorer.exe'. Make sure you typed the name correctly, and then try again. To search for a file, click the start button, and then click search. Although I could detect and remove several suspicious files using Malwarebytes & Microsoft Security Essentials, the problem still remains. The interesting point is that if I right click on one folder and select Open or Explore from the menu bar, I can open the folder! but if I double click on the folder, it does not open and I get the above error message. How can I fix this problem? Any advice would be appreciated! Update: I formatted the C: drive (NTFS), a deep format, and installed a fresh Windows XP on it. I am not getting this error when I double click on C drive icon anymore. But the same error appears when I double click on other drive names. Maybe I should format them too!

  Read the article

• HAProxy "503 Service Unavailable" for webserver running on a KVM virtual machine

  - by Menda

  I'm setting up a server with KVM (IP 192.168.0.100) and I have created inside of it one virtual machine using network bridging at 192.168.0.194. This virtual machine has an nginx instance running, which I can access from the server or from any computer computer in the internal network just typing in the browser http://192.168.0.194. However, I try configure HAProxy in the same server that hosts KVM and looking the status page of HAProxy it always shows the virtual machine as "DOWN". If I try from the server http://localhost, it should be the same than if I go to http://192.168.0.194. My goal is to build a reverse proxy, but I tried this little example and won't work. What am I doing bad? This is my config file in the server: # /etc/haproxy/haproxy.cfg global maxconn 4096 user haproxy group haproxy daemon defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen ServerStatus *:8081 mode http stats enable stats auth haproxy:haproxy listen Server *:80 mode http balance roundrobin cookie JSESSIONID prefix option httpclose option forwardfor option httpchk HEAD /check.txt HTTP/1.0 server mv1 192.168.0.194:80 cookie A check Thanks.

  Read the article

• Linux Uninstalling errors

  - by Zack

  I want to uninstall back-track 5 so I deleted the partitions for back-track os. After deleting the partition that used to be for back-track becomes free space as in picture. But I can't delete that partition nor creating a new partition. I used G-Parted from hiren boot cd but it says there is no partition table, you need to create a partition table. But actually I have 5 partitions already. And I thought of restarting might fix it. But after showing post screen my laptop show grub error. I don't know what to do, and I tried to install back-track again to fix the problem but it also says that i do not have any partitions. I can only boot windows by passing through hiren boot cd. But most of the time My computer is not recognizing the external dvd drive, nor the internal so i have to restart again and again, hoping to catch the time computer recognize the dvd drive. Can I change the boot loader to correct the grub error? SOLVED : I have solved the grub error by writing MBR again by using EasyBCD But I still have the format error.

  Read the article

• Convert a cassette tape recording to digital format

  - by Electric Automation

  Has anyone been successful with transferring audio cassette tape recordings to a digital format? I would like to preserve old cassette tape recordings of my grandparents to some digital format: MP3, WAV, etc... The quality of the tapes are mediocre. I think I can handle the quality restoration but getting the audio from tape to digital is my question. Below is a list of the hardware that I can work with: Cassette Deck: I have a Technics stereo cassette deck model RS-B12. It has separate left and right IN and OUT RCA type jacks on the back. In the front it has a headphone phono jack, plus left and right mic input phono jacks. On the computer side: -I have a Windows Vista PC with no additional software other than what came with the machine from Costco. No sound editing software that I can see. There is no sound card on the PC. On the front panel there is a mini-phono mic input jack and there are several different types of in/out mini-phono jacks on the back. In addition, USB and Firewire. I also have access to a new (2009) iMac with a mini-phono input jack for a powered mic or other audio source and GarageBand that has come with the computer. In addition, USB and Firewire. What are my options for getting these cassette recordings into a digital format? Whats the best format? What sort of wires would I need and will I want to utilize the USB or Firewire or can I simply use the audio inputs on the PC (or Mac) to receive the audio stream?

  Read the article

• Mac Grey/White Screen of Death

  - by cust0s

  The other night I updated my iTunes to the latest version (through Software Update) when I came to turn on my computer I was greeted with the dreaded white screen of death. I use an early 2008 iMac 24". I've tried the basic things, unplugging/turning off accessories, trying to boot from the install disk, reseting pram, etc, etc. Still no luck and no change what-so-ever. All I've been able to ascertain that my keyboard still works (by ejecting). I should point out that I did recently replace my Hard drive with a Western Digital Black 500GB (though the computer is well out of warrenty) and I'm a little concerned that the problem could be the screen. Update (18/05/10): I've been told that I could be getting the White/Grey screen of death because the optical flex cable is damaged (aparently this is common). Apparently the Optical Drive is part of the POST sequence, and an inability to read the drive can result in failure for the system to move on to other bootable volumes. More info here. I will disable the optical drive and see if that works.

  Read the article

• Photoshop CS6 Corrupted File recovery

  - by Ben Franchuk

  Last night I was working on a client application mock-up in photoshop, but was goin to take a break from my work so I saved the .PSD file on my internal HDD and put my computer into stand-by mode once the file had finished saving. Unfortunately my computer crashed while it was entering stand-by and shut itself down (photoshop was still open). I did not boot it again to make sure all my files were ok because they had already been saved, but today once I opened up the file again it was extremely corrupted and also completely un-editable (screenshot bellow). so what im asking is there any way to recover my work, or at least some of it? i have put in a good few days work on this project and would hate to have to restart it. the size of the file is 3070 KB, even though it reads as 712 KB in photoshop. i dont know if these file sizes are larger or either smaller than the original non-corrupted file's size, but considering all the layers in the file i suspect it was larger before it corrupted. im using windows XP professional 32bit SP3. both my OS and said .PSD file are located on the same internal HDD (74.4 GB). i do have an external HDD (1.5 TB) but i primarily only use it for movies music and tv shows. i dont know if it was plugged in t the time of me editing the document last, though, if it means anything. i have tried many image and PSd recovery softwares but none have returned any results that may help recover my work. edit: i tried using a photo reccovery software (odboso Photorecovery) that actually seems to recover the corrupted file in question judging by the size of the file, but i cannot recover it because of the licence fee. knowing that the file is still likely on my HDD, what location might it be located?

  Read the article

• Unable to connect to cable modem when connected to VPN

  - by Spuas

  the scenario is as follows: First I have a cable modem which gives the internet connection. The network is 192.168.0.0/24 and its IP is 192.168.0.1 Second line, I have a router connected to the cable modem. Its "outside" IP is 192.168.0.12. This router creates network 192.168.123.0/24 and its IP there is 192.168.123.254. My computer is wired to the router with IP 192.168.123.126. At this point I am able to access both devices web interfaces by their IPs on a browser (192.168.123.254 for the router and 192.168.0.1 for the cable modem). The problem I have is when I connect to a VPN from the computer. Then I am connected to a second network 10.0.0.0/24 and I get IP 10.0.0.200 (along with 192.168.123.126). I can connect to the router but then I loose connectivity to the cable modem: I cannot acces it through the browser, neither making a ping to it or a tracert. I have tried to add a new route to the windows routes by typing route ADD 192.168.0.1 MASK 255.255.255.0 192.168.123.254 but I cannot access it anyway... Am I missing something on the route adding? Which is the propper way of doing this? Thanks

  Read the article

• BIOS unable to boot CD or Hard Drive

  - by Gabriel

  Motherboard Intel DQ35MP. HDD Caviar Green 1TB. I'm having problems with my BIOS and/or hard drive/disc drive. Came back from a trip, booted my computer, and realized that the BIOS wasn't booting anymore, just a black screen with no beep sounds. Only fans and lights on. Then I thought it might be caused by the video card, I removed it, and still no BIOS screen. Then I removed the hard drive and voila BIOS screen is back again. If the hard drive is defective then I can check that with a Rescue Disk. I inserted the CD on the Disc Tray but the computer did not respond to it, the screen freezes in black with an "E7" string at the bottom right corner just after the BIOS screen, this happens with or without discs. BIOS settings are set to default, and CD reading is on top of the boot device list. EDIT I removed the BIOS battery, rebooted the CPU, the BIOS screen showed up, and then it freezed in E7. Placed the BIOS batttery, rebooted and same thing, we are stuck with the E7 string. I uploaded a video to illustrate the problem http://www.youtube.com/watch?v=13jPdBcIrBU

  Read the article

< Previous Page | 264 265 266 267 268 269 270 271 272 273 274 275  | Next Page >