Search Results

Search found 9147 results on 366 pages for 'big smile'.

Page 269/366 | < Previous Page | 265 266 267 268 269 270 271 272 273 274 275 276  | Next Page >

  • Network speed between a VM and another machine which is not residing on the same host, is 11MB/s at most

    - by Henno
    Problem Network speed between a VM and another machine which is not residing on the same host, is 11MB/s at most. Topology Facts ESXi5 version is 5.0.0.504890 VM has the latest Vmware Tools installed VM is using E1000 network driver Physical box has Win Srv 2008 R2 as the OS CrystalDiskMark says the drive on physical box can read/write 100MB/s vCenter is another vm on esx both vm and physical box are showing 1Gbps link speed Configuration Networking shows vmnic0 as 1000 Full NTttcp is a client/server tool from Microsoft for measuring pure network throughput Here's what I've done so far: Test1: VM is running Filezilla FTP Server (default settings, one user account made) Physical box is running Filezilla FTP Client (default settings) Physical box is uploading a big file to FTP server Transfer speed (as observed by Windows Task Manager on both machines): ~11MB/s (bad) Physical box is downloading that file from FTP server Transfer speed (as observed by Windows Task Manager on both machines): still ~11MB/s (bad) Could it be disk performance issue? Test2: Physical box is running ntttcpr.exe -a 6 -m 6,0,VM_IP_ADDRESS VM is running ntttcps.exe -a 6 -m 6,0,PHY_BOX_IP_ADDRESS Transfer speed (as observed by Windows Task Manager on both machines): ~11MB/s (bad) Could it be switch performance issue? Test3: physical box is running vSphere Client I open Summary Storage datastore Browse Datastore... from physical box and upload a file to datastore Transfer speed (as observed by Windows Task Manager on physical box): ~26-36MB/s (good) Could it be a vm specific issue? Test4: Installed ntttcp to another vm on the same esx server Measured network performance between vms on the same esx server with NTttcp Transfer speed (as observed by Windows Task Manager on physical box): ~90-120MB/s (excellent :) Test5: I have another esx server on the same site, connecting to the same datastore and same switch. Those two ESX servers have both 2 NICs. One NIC goes to switch while the other goes directly to the other ESX server. vMotioned one of the testing vms off to the other ESX host Measured network performance between vms on different esx servers with NTttcp Transfer speed (as observed by Windows Task Manager on physical box): ~11MB/s (bad) While I'm aware of these: ESXi 4.1 slow file transfer ESXi 5 network performance is slow Debian Etch and ESXi slow network speeds VMWare ESXi slow file copy to guest they did not help (or I must have been missed something)

    Read the article

  • Membership in two domains

    - by imagodei
    Hello! I would your suggestions for an effective solution for a person, who needs to access resources in two Windows domains and wants to use one computer. It's about our CEO, who has accepted a second position in another company. Accessing files and folders isn't big problem. The greatest challenge I see is that he wants to conveniently access Exchange accounts in both companies; he would like to send and receive mail in single Outlook if possible (two profiles?) There is also a challenge with calendars: he would like to have one calendar for all activities from both Exchange accounts. Creating a POP3 account for accessing second Exchange server is a last resort, because obviously there is a problem with scheduling meetings and other calendar related tasks. Forwarding and receiving all mail/tasks on primary Exchange server is inconvenient because simple replying to original sender is disabled; and also when manually changing the recepient, he will receive mail from the wrong address. We were considering Virtualisation, that is setting up an instance of virtual machine inside existing installation and then joining this virtual computer to a second domain. Then installing another MS Outlook. This would of course mean two different Outlook accounts, two different calendars, but would at least enable our CEO to access all information from a single laptop. Does anyone have any other idea? I know setting up two domains on a single computer is a no-go (without much hacking at least), but effective workarounds are appreciate. The thing I am looking here is high usage/efficiency/productivity, but also as elegant solution from the administration point of view. Thank you very much (if you managed to read this through, this is a good sign ^_^ )

    Read the article

  • Including email, IMs, configs, etc. in documentation or notes

    - by Jason Antman
    The shop I work in is pretty laid-back. We're on a documentation kick, only because historically we've been very bad with it. We do a lot of our brainstorming in face-to-face meetings, and also do a lot of communication via IM in addition to email. While I'm usually pretty good about documentation and keeping copious lab notes, I just finished a build of a host and spent hours searching through IMs, emails, files on my workstation, etc. to pull out anything I missed in my lab notes, which formed a large amount of the basis for the internal documentation. Does anyone have any thoughts on, aside from manually saving things to a project directory, managing various data sources (especially email and IM) and tracking them on project basis? Ideally, I'd like an easy way to put copies of emails, IM logs, etc. into a project-specific directory on my workstation and then just have a cron job that syncs that up with a shared folder. This isn't really a candidate for anything more advanced, as the bulk of the data will be copies of configs, code, etc. Here are the big restrictions: Email is via a centralized Zimbra install, so nothing can happen server-side. My workstation is Linux. Aside from writing Pidgin and Thunderbird plugins that let me tag chats and emails as belonging to a project, and then copy them to the appropriate place... any thoughts? Suggestions? Thanks, Jason

    Read the article

  • Legal IT documents

    - by TylerShads
    I have been wondering this past week because my big boss told me to start keeping track of all the things I have fixed, how to fix them, etc. Which is reasonable and have been doing anyway. But then a related question came to mind. What kind of documentation should I have on hand as far as users go. More specifically I am talking in terms of EULA, ToC, etc (correct me please if I'm using the wrong terms) Or more specifically a policy, so to speak, for the users and such. Can't say I'm a legal expert, otherwise I'd be a lawyer. The environment the users are in is pretty laid back so I don't forsee a problem. But assume that there should ever arise a problem, what should I have written up/have on hand? EDIT: I really should have noted that we are a medical transport facility and have patient records so I know that something must be done there to comply with HIPAA policies I believe. I do like what anthonysomerset said about the "If I get by a bus" Scenario and want to apply it not only to the documentation I am currently writing but also for if say an employee were to steal info from the server or edge cases, theft, etc. As far as our staff, its relatively small as in a single HR person, no legal department aside from the 2 owners' lawyers and me being the only IT person on staff with a guy who is no more than a mac superuser.

    Read the article

  • Adding users to Sharepoint when they are not in the same domain

    - by jim-work
    Bear with me as I explain this, I'm working my way through Sharepoint access as I go, but I'll clarify my question as I go along. The Problem We have about 10,000 users who need access to our Sharepoint 2005 based reporting. Because our organization is migrating from one domain to another, we need to add each user twice, once for each domain. For the current domain, this is no problem, we've got a powershell script that I tweaked to add all the users in a given CSV file, this takes about 5 minutes to run. The big problem we're having is with users who are NOT in our currently active domain. Because the sharepoint server cannot authenticate the new users, we can't add them directly. What we're doing is creating a temp user, then using STSADM.EXE to migrate that test user to the proper domain/user_name for each of our 10,000 users. The creation and migration takes about 5 seconds per user, or well over 12 hours to run. The Question Has anyone encountered this before? Is there a way to add users without requiring AD authentication? Why is STSADM.EXE running so slow? Thanks a lot for any advice or direction anyone can give me.

    Read the article

  • Remote Desktop Zooming

    - by codeulike
    Using Remote Desktop from a device with a hi-res screen (say, a Surface Pro) is decidedly tricky - as everything displays 1:1 scale and so looks tiny. If the machine you are remoting into runs Server 2008 R2 or later, you can change the dpi zooming setting (see here). But for older hosts, that doesn't work. Using normal Remote Desktop, you can connect with a lower resolution, say 1280x768, and turn on smart-sizing. However smart-sizing can scale down (to display a huge desktop in a small area) but does not seem to scale up (to display a small desktop in a big area). Using the Windows 8 Remote Desktop App, you can zoom - but you cannot set the default resolution of the host. What I want is a lower resolution in the host, scaled up to fit my screen. So both of those are close to what I want, but dont quite work. So question is: Does the Remote Desktop App allow screen resolution to be set somehow? Is there some other Remote Desktop client that can handle zooming better?

    Read the article

  • vim coloring for git

    - by kelloti
    I'm on Windows and my vim loads with a terrible colorscheme with vim. The message is blue on black (so I can't see what I'm typing). I need to change the colorscheme, but :colorscheme slate doesn't do anything. :version vim - vi improved 7.3 (2010 aug 15, compiled oct 27 2010 17:51:38) ms-windows 32-bit console version included patches: 1-46 compiled by bram@kibaale big version without gui. features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent +clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv +cscope +cursorbind +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +gettext/dyn -hangul_input +iconv/dyn +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse -mouseshape +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +persistent_undo -postscript +printer -profile -python -python3 +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl -tgetent -termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -xfontset -xim -xterm_save -xpm_w32 system vimrc file: "$vim\vimrc" user vimrc file: "$home\_vimrc" 2nd user vimrc file: "$vim\_vimrc" user exrc file: "$home\_exrc" 2nd user exrc file: "$vim\_exrc" compilation: cl -c /w3 /nologo -i. -iproto -dhave_pathdef -dwin32 -dfeat_cscope -dwinver=0x0400 -d_win32_winnt=0x0400 /fo.\objc/ /ox /gl -dndebug /zl /mt -ddynamic_iconv -ddynamic_gettext -dfeat_big /fd.\objc/ /zi linking: link /release /nologo /subsystem:console /ltcg:status oldnames.lib kernel32.lib advapi32.lib shell32.lib gdi32.lib comdlg32.lib ole32.lib uuid.lib /machine:i386 /nodefaultlib libcmt.lib user32.lib /pdb:vim.pdb -debug My $HOME\_vimrc looks like colorscheme slate syn on set shiftwidth=2 set tabstop=2 and my $VIM\vimrc is the stock vimrc that comes with the Windows Vim distribution. How do I change my console Vim colorscheme? Especially for Git commits.

    Read the article

  • Tunneling a public IP to a remote machine

    - by Jim Paris
    I have a Linux server A with a block of 5 public IP addresses, 8.8.8.122/29. Currently, 8.8.8.122 is assigned to eth0, and 8.8.8.123 is assigned to eth0:1. I have another Linux machine B in a remote location, behind NAT. I would like to set up an tunnel between the two so that B can use the IP address 8.8.8.123 as its primary IP address. OpenVPN is probably the answer, but I can't quite figure out how to set things up (topology subnet or topology p2p might be appropriate. Or should I be using Ethernet bridging?). Security and encryption is not a big concern at this point, so GRE would be fine too -- machine B will be coming from a known IP address and can be authenticated based on that. How can I do this? Can anyone suggest an OpenVPN config, or some other approach, that could work in this situation? Ideally, it would also be able to handle multiple clients (e.g. share all four of spare IPs with other machines), without letting those clients use IPs to which they are not entitled.

    Read the article

  • How can I report a website that uses the webmail APIs to send spam?

    - by Igoru
    I've signed up for a cool job website that, unfortunately, asks you if you want to "invite your friends", and if you say so, you can give them access to your Gmail contacts to send the invite. However, contrary to what everyone would be expecting, they don't give you a list of who you want to invite; instead, they simply directly send spam to your entire contact list, like old-fashioned Outlook viruses. When you complain about this with them, they simply say "we will check the application and see if there is anything that might be confusing for the users". For me and some other friends (that felt for the same prank), this is a clear break on web best practices and a big disrespect on the users' trust. Thus, I would like to know what can we do to stop the website of using Gmail/Yahoo/Outlook APIs to send spam this way. P.S.: I wonder what would happen if I've given this website the access to post in my Facebook timeline as well. I've got a couple of calls from relatives asking about the email and I wonder how many unrelated people got this spam, like HR addresses from my past and whatnot.

    Read the article

  • What precautions should I take once defective RAM has been replaced?

    - by DustByte
    I recently discovered that my RAM is faulty (MemTest86+). I am waiting for new RAM to be sent to me.  It was through sheer luck that I discovered something was wrong. I was copying a large amount of big files and decided to verify the copies by their checksums. I discovered strange discrepancies, and noticed that checksum computation for the same file was not consistent. Now, this is the only problem I have encountered; no BSOD, no crashes, no errors. In a sense this makes me more worried than if I would have had massive crashes. I have no idea for how long the RAM has been faulty, and I have no idea if corrupt bits have been saved into files on my hard drives. I do know the RAM was fine two months ago (tested it back then). I am a user of Adobe's Lightroom and I am worried that photos or the catalog itself could carry corrupt data. Question: what should I do once new healthy RAM has been installed? Reinstall Windows (I'm using Windows 7, 64 bit)? Is there a risk that I will be presented with nasty surprises in the future if I don't? What about personal files? I have backups of some of the files but for newer files I'm not sure I can even trust the backups. It's going to take me many hard hours to manually replace files with older versions, or compare checksums.

    Read the article

  • Ext3 fs: Block bitmap for group 1 not in group (block 0). is fs dead?

    - by ip
    My company has a server with one big partition with Mysql database and php files. Now this partition seems to be corrupted, as reported from kernel messages when I tried to mount it manually: [329862.817837] EXT3-fs error (device loop1): ext3_check_descriptors: Block bitmap for group 1 not in group (block 0)! [329862.817846] EXT3-fs: group descriptors corrupted! I've tried to recovery it running tools from a PLD livecd. These are the tools I have tested: - e2retrieve - testdisk - photorec - dd_rescue/dd_rhelp - ddrescue - fsck.ext2 - e2salvage without any success. dumpe2fs 1.41.3 (12-Oct-2008) Filesystem volume name: /dev/sda3 Last mounted on: <not available> Filesystem UUID: dd51610b-6de0-4392-a6f3-67160dbc0343 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal filetype sparse_super Default mount options: (none) Filesystem state: not clean with errors Errors behavior: Continue Filesystem OS type: Linux Inode count: 9502720 Block count: 18987570 Reserved block count: 949378 Free blocks: 11555345 Free inodes: 11858398 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 16384 Inode blocks per group: 512 Last mount time: Wed Mar 24 09:31:03 2010 Last write time: Mon Apr 12 11:46:32 2010 Mount count: 10 Maximum mount count: 30 Last checked: Thu Jan 1 01:00:00 1970 Check interval: 0 (<none>) Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 128 Journal inode: 8 Journal backup: inode blocks dumpe2fs: A block group is missing an inode table while reading journal inode e2fsck 1.41.3 (12-Oct-2008) fsck.ext3: Group descriptors look bad... trying backup blocks... fsck.ext3: A block group is missing an inode table while checking ext3 journal for /dev/sda3 I tried also backup superblocks, same error result. There's any other tools I have to test before considering these disk definitely unrecoverable? Many thanks, ip

    Read the article

  • Reconnecting OST with Exchange

    - by syrenity
    Hi. I have a quite big problem with customer's MS Exchange. The server got it's disk filled about 2 weeks ago, so it's currently offline. They plan to upgrade it, but not in hurry, as they use it mainly for OWA and back-up - the mails exchange is done via SMTP and POP3. Trying to diagnose some problem today, one of the users has (following the ISP instructions), removed the Exchange account from Outlook, which essentially left the OST orphaned. The user naturally didn't move the emails or any other data to the Archive / PST before, so these emails located on the OST only. So currently I'm trying to figure out how to restore them. There are 2 options: 1) Make the user buy some tool to convert them to PST, and import as archive / main Outlok file? 2) Reconnect the Outlook to Exchange (once it up), let it sync the old server content, then shutdown Outlook and replace the new OST with the old one, start Outlook again in offline mode and move these files to archive. 3) Any other method? Can someone advice what would be the best approach here? The used versions are Outlook 2007 and Exchange 2003. Thanks!

    Read the article

  • What is the peak theoretical WiFi G user density? [closed]

    - by Bigbio2002
    I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

    Read the article

  • Windows 2003 DC to Windows 2008 R2 DC with same name and same IP

    - by TheCleaner
    Environment = Windows 2003 native domain with 8 DCs I've got an old domain controller that is running 2003, CA Enterprise role, DHCP, DNS, a few GPO scripts that point to shares on it, and some other minor functions. All our servers point to it as their primary DNS, and there's lots of references to its IP or name throughout the domain at this point (8+ years later). I really don't feel like manually changing all of this, it would be a pretty massive undertaking. I want to follow this guide: http://msmvps.com/blogs/acefekay/archive/2010/10/09/remove-an-old-dc-and-introduce-a-new-dc-with-the-same-name-and-ip-address.aspx to hopefully end up with basically an "in-place upgrade" so to say. I considered just doing a P2V of the box, but we don't really want to keep it around running 2003 to be honest. I also considered using a CNAME and adding a 2nd IP (the old one) but again, it seemed like it would be cleaner using the attached link. My actual question: Any gotchas or big caution signs when doing what the link suggests? Anyone gone down this road and have advice on how to proceed?

    Read the article

  • Green flickering pixels that move with black images

    - by user568458
    Strange question... Occasionally, on my LCD screen, pixels that should be black flicker rapidly and constantly between black and green, about 4 flickers a second. The crazy part is, unlike dead/stuck pixels, they are relative to content on the screen and move with it. For example, I might be looking at a web page with a picture that has lots of black. There might be a couple of green flashing pixels in that black that shouldn't be there. I scroll the page, and the green flickering pixels move with the image. It seems that everyphysical pixel is fine, but somehow something interprets part of the image in a way that causes flickering green... It's not just in a web browser. My first thought was to blame a trolling blogger cunningly uploading an animated gif that simulates a failing pixel... but it happens in a wide range of applications. It seems to occur randomly, other than that it seems to only occur in areas of pure black, and it's always pure 100% green. It happens rarely enough that it's not a big deal, but it's such a strange problem it bugs me. I can't find any info on anything like this. I'm not even sure if it's hardware or software. Any ideas? (windows 7 laptop connected to LCD by DVI to HDMI cable)

    Read the article

  • Directory tree in a Resource without extraction...

    - by Corelgott
    Hi all, i am looking for a way to store a complete directory including sub directories in an application's resource and not have to extract it to use it. Details: We would like to use GeckoFx (Gecko as C# Component) in one of our applications. GeckoFX needs the XUL-Runner and needs to find it's folder structure We have some other data which I would not prefer to extracted to the customer's pc; At least not onto something persistent like a hdd... Getting the complete directory into the resources is not that kind of a big deal. Compress to one file and done. But not writing it to the disk to use it is something else. I have a strong dislike against temp folders and such things. Would anything like a RAM drive be possible? Some part of the RAM beeing mounted? Does something like this even exist as a lib, or would this only be possible by a device driver? Any thoughts on this? Thanks in advance! Corelgott

    Read the article

  • Struggling with proper way to setup Permissions on Linux/Apache Web Server

    - by Dr. DOT
    Your expert experience and assistance is great, greatly appreciated here. I have been running a LAMP server for a long time, yet I still struggle with the best way to set file & directory permissions for FTP and WWW protocol activity. My Control panel is WHM/cPanel (not that it makes a difference), and out-of-the box: files are owned by the user account setup in WHM (eg, "abc") files have a group setting of "abc" as well file permissions are created with 644 directories are owned by "abc" directories have a group setting of "abc" directories permissions are created with 0755 Again, these are the default permission settings. Now everything is fine with FTP activity, but please advise me if any of these file/directory settings create issues, especially with security. Here's where my struggle comes into play. I have PHP apps that allow a visitor to create, edit, rename, delete, etc. sub-directories and files in certain selected directories. PHP runs as "nobody" on my server. So in order to get my PHP/Web apps to work, I have had to: chown nobody * chgrp nobody * chmod 0777 * to everything in these certain & selected sub-directories. I know this is probably a huge security whole (so don't ask me for any links :) but how should I set all the permissions to allow my FTP user to do his thing while allowing the PHP apps to do their thing will also "minimizing" any security risks and exposures? I know that big CMS systems like Drupal, Joomla, WordPress and so on, handle this. Thanks ahead of time for reading through this and offering your expert advice!

    Read the article

  • Failure to connect to admin share pops up dialog

    - by Jan
    I'm having an issue with a curious error message when accessing the administrative share on a remote machine. Specifically, the client is logged in as the domain administrator on the machine A, and runs some code that tries to access the admin share on B (a domain member). The access is done in .NET, along these lines (though I am not sure if the method of access makes a difference): string path = @"\\B\admin$"; if (Directory.Exists(path)) { try { path += @"\temp\"; if (!Directory.Exists(path)) { Directory.CreateDirectory(path); } path += "myfile_remote"; File.Copy("myfile", path); Now, on some machines this fails. That is not a big problem as we have a fallback. I'd like to know why but it is not the real issue. The problem is that running this piece of code causes a dialog box to pop up for the logged-in user on B, saying "network error trying to access \\B\admin$\temp\myfile_remote. Contact the network administrator and ask for the correct permissions". Unfortunately, it is a foreign language Windows so I'll spare you all posting a screenshot. It is skinned like a standard Windows dialog box. Why exactly is that dialog box popping up for the user and is there anything I can do about it? Edit to add: B is a Windows 7 Enterprise installation. The client is not aware of any GPO policies being installed. There is AV from Trend Micro installed.

    Read the article

  • Backup solution to backup terabytes and lots of static files on linux server?

    - by user28679
    Which backup tool or solution would you use to backup terabytes and lots of files on a production linux server ? Note that the files are all different and almost never modified, and usage is mostly adding files, so data volume is today 3TB growing all the time at around +15GB/day. Please do not reply rsync. Basic unix tools are not enough, rsync does not keep history, rdiff-backup miserably fails from time to time and screw the history. Moreover these are all file based backup, which put a lot of IOwait just to browse directories and query stat(). But i guess, except R1Soft CDP, there is no way around that. We tried R1Soft CDP backup, which is block level backup, and it proved good and efficient for all our other servers, but systematically fails on the server with 3 terabytes and gazillions of files. That is already more than 2 months that the engineers of R1Soft and datacenter are playing a hot ball game... and still no backup except regular rsync We never tried big commercial solutions, except R1Soft CDP since it was provided as an optional service by the datacented hosting our servers.

    Read the article

  • Connecting multiple access points

    - by mohsen farahanipoor
    I'm working on a big project. We want to create a wireless network throughout the building with 15 floors. My idea is that we should set up one unified wireless access point at least in each floor...in case of signal attenuate, we use Access point extender/repeater. I selected DWL-6600AP from among D-Link industrial access points. I want to implement a single wireless LAN throughout the building. Is it possible to combines multiple DWL-6600 access points to achieving just a single WLAN? Can a wireless switch controller do this task? Can these Access Points interfere with each other? What is the solution? I read D-Link website's learning materials, but I am still confused. My other question is around the connecting these APs to Wireless Switch Controller - Is it possible to use power line for connecting DWL-6600 to Wireless Switch Controller device? My main goal is that clients with portable devices such as laptops should be easily connected to the network to share & have communication without any more manual configuration as they are already connected to a single network.

    Read the article

  • How to set up a easy-to-use proxy for the whole system with WinXP client and server?

    - by Pekka
    I am working together intensively with a colleague on the Canary Islands. We speak through live messenger and work together using a RDP software. She has frequent problems with connections to certain big-name and small-name sites (amongst others live.com, google.com, gmx.de) very likely to be caused by the spanish provider (the connections simply time out, this has been going on for weeks already). I have been thinking about setting up my computer as a proxy to make these connections work. I have a DSL connection and am behind a NAT capable router that I control. Does anybody know a simple, "one-click" way to transport ALL network traffic through a remote proxy? Without having to set proxy settings for each application that uses the internet? VPN is not an option, because I am behind a firewall that supports protocol 47 and such, but I have never succeeded in getting an incoming VPN connection to work. I can however redirect normal traffic using NAT. A VPN solution that does not need strange protocols would also be an option.

    Read the article

  • Are there compact external USB audio interfaces which are better than a on-board sound?

    - by rumtscho
    I am asking this for a friend. He loves his voice recognition software and dictates a lot of text using a headset. Now he has a new laptop, which only has a combined mic/headphones output, and wanted to buy an adapter. I told him to get an external USB sound interface instead, as the better sound quality will probably increase the hit rate of the voice recognition. He agreed, but when he saw a picture of the SoundBlaster X-Fi, he said that it is way too big, because he wants to carry the thing everywhere. He'd rather have one of these small things which are the size of a flash memory stick, with only one mic and one phones output, period. Now I am not sure whether these mini interfaces would produce a sound better than onboard sound. They all seem to come not from established audio interface manufacturers, but from electronic accessories manufacturers like Speedlink, or just noname brands. Is there a compact audio interface with good A/D quality (it is OK if the price is comparable to that of the bigger interfaces, even if there is no additional functionality like Chinch in-/output etc)?. And if there isn't, will the noname soundcardsticks offer any advantage over a simple adaptor for the onboard sound?

    Read the article

  • Scaling databases with cheap SSD hard drives

    - by Dennis Kashkin
    Hey guys! I hope that many of you are working with high traffic database-driven websites, and chances are that your main scalability issues are in the database. I noticed a couple of things lately: Most large databases require a team of DBAs in order to scale. They constantly struggle with limitations of hard drives and end up with very expensive solutions (SANs or large RAIDs, frequent maintenance windows for defragging and repartitioning, etc.) The actual annual cost of maintaining such databases is in $100K-$1M range which is too steep for me :) Finally, we got several companies like Intel, Samsung, FusionIO, etc. that just started selling extremely fast yet affordable SSD hard drives based on SLC Flash technology. These drives are 100 times faster in random read/writes than the best spinning hard drives on the market (up to 50,000 random writes per second). Their seek time is pretty much zero, so the cost of random I/O is the same as sequential I/O, which is awesome for databases. These SSD drives cost around $10-$20 per gigabyte, and they are relatively small (64GB). So, there seems to be an opportunity to avoid the HUGE costs of scaling databases the traditional way by simply building a big enough RAID 5 array of SSD drives (which would cost only a few thousand dollars). Then we don't care if the database file is fragmented, and we can afford 100 times more disk writes per second without having to spread the database across 100 spindles. . Is anybody else interested in this? I've been testing a few SSD drives and can share my results. If anybody on this site has already solved their I/O bottleneck with SSDs, I would love to hear your war stories! PS. I know that there are plenty of expensive solutions out there that help with scalability, for example the time proven RAM-based SANs. I want to be clear that even $50K is too expensive for my project. I have to find a solution that costs no more than $10K and does not take much time to implement.

    Read the article

  • Application for time and project management

    - by user10826
    I want to improve the way I organize my projects/tasks/schedule What I do now is: keep an excel sheet with the name of the most important tasks/projects, I look at it at the beginning of each day and decide the ones I will focus on on iCal I write down events for each day, or for a concrete time (13 to 14 hours). I set up each day the tasks I want to accomlish, and allocate them hours I use Things (culture code) to keep info about tasks and projects not very important and which are not time allocated yet (GTD name = someday) I use Mail on Mac and create folders for the mails I want to process with the name of the different projects I save the main info for each project on freemind maps My system works well at the moment but it is pretty complicated to use. I want to make it better and I am looking for something with these requirements: must be 100% offline accessable it should use as less programs/resources as possible, ideally just one program should be able to manage all my info I can use the GTD methodology mixed with priorities and I can allocate each task converted to event on my calendar I can have different daily/weekly, etc views on a calendar to see the "big picture" must run on mac os x leopard price does not matter, I will pay for this So, according to your experience, can you recommend me something like this? Thanks

    Read the article

  • Finding matching columns in excel

    - by fakaff
    I've never used excel before so I need the simplest solution available, and this is a work assignment due this week so I didn't have time read much of the documentation. Basically, I have two tables, A and B, and they are both thousands of rows long. Description of my task: right now (since I don't know better) I'm manually doing this: Go to row i in table B. Select entries in columns B(a, b, c) of that same row. Look for a row in table A where column A(b) matches row B(a). Paste the entries of columns B(a) of row i at the end of the row found in the last step. Repeat for row i + 1. Example: row B(cat, dog, mouse) matches A(mammal, cat, Mr. Whiskers). So I would paste B after A and have A(mammal, cat, Mr. Whiskers, cat, dog, mouse). Note: I am not joining tables. I am merely extending table A by pasting row A(b) if row A(b) matches row B(a). Also, sometimes entries are spelled slightly differently. Using wildcards to search for candidates would be of help. As the description should let on, this task is very tedious and inefficient if I don't know how to automate some operations (there are thousands of entries). Any quick tips as to how to be more productive is a big help.

    Read the article

< Previous Page | 265 266 267 268 269 270 271 272 273 274 275 276  | Next Page >