Search Results

Search found 16644 results on 666 pages for 'traffic management'.

Page 269/666 | < Previous Page | 265 266 267 268 269 270 271 272 273 274 275 276  | Next Page >

• Linux QoS: bulk data transmission during idle times

  - by syneticon-dj

  How would I do a QoS setup where a certain low-priority data stream would get up to X Mbps of bandwidth, but only if the current total bandwidth (of all streams/classes) on this interface does not exceed X? At the same time, other data streams / classes must not be limited to X. The use case is an ISP billing the traffic by calculating the bandwidth average over 5 minute intervals and billing the maximum. I would like to keep the maximum usage to a minimum (i.e. quench the bulk transfer during interface busy times) but get the data through during idle/low traffic times. Looking at the frequently used classful schedulers CBQ, HTB and HSFC I cannot see a straightforward way to accomplish this.

  Read the article

• Recommendations for VMWare web server environment with load balancer.

  - by Ben

  We run IIS websites on a VMWare production server that pull image content and video content from a separate IIS instance on another server (media server). The media calls (images and video) are straight http:// calls and not using a streaming application. During peak traffic periods, we clone the production server five times and have a load balancer distribute traffic to all five production servers. The media server does not get ramped up. We noticed that the processing and resources on the media server gets very taxed during this period. Would it make sense to run the IIS instance for the media server locally on the production server and have it cloned with the production servers, then have a rule on the load balancer negotiating these media calls from the website? Would it be better to allocate more resources (memory and CPUs) to the media server VM and not clone it with the production servers? Recommendations are sincerely appreciated.

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• Security of a free public VPN service

  - by Mark Belli

  I just started using VPNBOOK, which is a (very efficent) free VPN solution. I have a question: VPNBOOK user and pass used to connect to their vpn network are publicily available on their homepage; everybody uses them to connect to the vpn. Can a user intercept my wifi traffic and: Understand that my connections are directed to VPNBOOK servers. If point 1 is successful, then they could use VPNBOOK public user and pass to decrypt my traffic? I hope I am missing something, otherwise it would be a very big weakness and I would revert to a paid service (with a private account)

  Read the article

• Converge Voice and Data networks using Sonicwall

  - by skinneejoe

  We are looking to converge VOIP and Data traffic onto a single wire so that our client's VOIP phones pass data through to the users computer. We are specing out a new Sonicwall NSA appliance to handle routing functions and layer 2 switches to manage VLANS. Not a huge network, medium sized. What should I know about converging the networks onto a single wire? Obviously I'll want to prioritize voice traffic, is this handled solely in the Sonicwall with QoS configurations or do the layer 2 switches need to be configured differently? Any other pitfalls I should be aware of, or any good resources for learning more?

  Read the article

• SSH Socks Proxy wiith iptables REDIRECT

  - by Radium

  I have googled and haven`t found the answer on my question. Help me please. There are two servers: serverA with public IP 12.0.0.10 and an private IP 10.0.0.5 serverB with public IP 20.0.0.11 I have setup SOCKS proxy on serverB to serverA: ssh -D20.0.0.11:2222 [email protected] So when on my local machine in a browser i specify SOCKS proxy 20.0.0.11:2222 (serverB:2222) as external IP while browsing i get 12.0.0.10 (serverA IP). That is ok. As well if i go onto http://10.0.0.5 (serverA private IP) it is also reachable. That is what i need. I want to make servers A private IP to be available through servers B public IP on certain ports but without specifying SOCKS in my browser. I could use ssh port forward but the problem is - i need to forward many ports and do not know which exactly - i know only the range. So when i connect to 20.0.0.11 to any port , for example, from 3000:4000 range, i want that traffic to be redirected to 10.0.0.5 on the same port. That is why i`ve decided maybe SOCKS proxy via SSH and iptables REDIRECT could help me. Client - serverBPublicIP (any port from range 3000:4000) - serverAPublicIP - serverAPrivateIP (the port was requested on serverBPublicIP) On serverB i do: ssh -D20.0.0.11:2222 [email protected] iptables -t nat -A PREROUTING -d 20.0.0.11 -p tcp --dport 3000:4000 -j REDIRECT --to-port 2222 But that does not work - when i telnet on 20.0.0.11:3001 for example i do not see any proxied traffic on the serverA. What should i do else? I have tried tcpsocks like this (in example i am telneting to 20.0.0.11:3001) Client -> 20.0.0.11:3001 -> iptables REDIRECT from 3001 --to-port 1111 -> tcpsocks from 1111 to 2222 -> SOCKS proxy from serverB to serverA on port 2222 -> serverA But i do not know what to do with the traffic on serverA. How to route it to its private IP. Help me please. I know, VPN removes all the hell i am trying to create, but i have no ability to use tun/tap device. It is disabled.

  Read the article

• Website hosted on IIS is not accessbile

  - by Tola Odejayi

  I have two sites set up in IIS on a remote machine RM; one on regular port 80, and the other on port 5773. From my local machine LM, I can access the site on 80, but I cannot access the one on 5773; I get a status code of 502 and an error code of 10060 (A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond) when I try to do this. I can access the 5773 site via IIS when I am logged into RM (i.e. by right clicking on a page on the site and going 'Browse'). I can also access pages on the 5773 site via a browser, again when I am logged into RM. I just can't do the same via a browser when I am logged into LM. I have ensured that port 5773 is open for outgoing traffic on LM. Could the problem be that I also need to ensure that port 5773 is open for inbound traffic on RM?

  Read the article

• Is there any way to limit my Internet connection to a per program basis?

  - by Igoru

  My Linux connection is REALLY free. I live in Brazil, so where I live I can only have 1 Mbit/s. Yes I know it's sad, but it's not the point. Everytime I'm updating my Ubuntu 9.04 or downloading something, it does eat all my bandwidth. Like, while update-manager is downloading the packages, I can see by netspeed applet in my panel that the incoming traffic goes to 110 kB/s. And then, my Emesene suddenly goes disconnected, and I can't navigate. As you can imagine, I can't use my Internet connection again until the packages are all downloaded or I cancel the update in the middle. As I said, same thing happens when I'm dowloading something, but less intrusive and immediate. The question is: is there any way to limit that APT/downloads traffic to some way I can still use my other Internet services, or to reserve some bandwidth for common navigation tasks (like we have on Windows, but I forgot this thing's name, it's like "something packages".

  Read the article

• Can a device (WAP or switch) be configured as an 802.1x supplicant?

  - by Allan Ross

  We are looking at implementing 802.1x on a wired/wireless network. What I am looking for is a device that can act as a supplicant and once authenticated on the network, is able to pass traffic from any downstream connected device. The point of doing this would be to allow a properly pre-configured device to be provided to a client user who could then connect any device on the downstream side of the device. We will be able to manage the aggregate traffic on the device without concern for what is connected on the far side. Am I dreaming; does every device out there support this and I just don't know it or is reality fall somewhere in the middle?

  Read the article

• trying to understand how Linux /etc/hosts file works with local and external IP addresses

  - by gkdsp

  Let's say I have a Linux server with an external IP of 123.456.789.012 and a local IP of 192.168.0.1. If it's /etc/hosts file looks like, for example, 123.456.789.012 host2.mydomain.com 192.168.0.1 host2.mydomain.com When an application on the server generates traffic to send using host2.mydomain.com, how does the server know whether to use the local or external IP address (since the same host name shows two IP addresses)? Or, does it need something additional than what I've presented here to decide this? Or, does it just sent it out as host2.mydomain.com and let the receiving end deal with it (if so, how to make sure traffic intended for local network indeed goes to local network)?

  Read the article

• Browser not parsing PAC file properly?

  - by mfinni

  I have a long PAC file. The browser(s) (IE and Chrome) are configured to use it and it generally does what it says on the tin. I have a domain that continues to go through the proxy although it should be going direct. // Match specific hosts and IPs entered as hosts if (buncha stuff || shExpMatch(host,"(*.newmarketinc.com)") || shExpMatch(host,"(newmarketinc.com)") || buncha stuff ) return "DIRECT"; Pactester shows that anything in the domain should be direct. h:\pacparser\pactester.exe -p h:\pacfile -u http://daas.newmarketinc.com DIRECT But we continue to pass traffic to hosts in this domain via the proxy. Wireshark and Fiddler both show this. How do i figure out how my browser has gotten brain-damage? Traffic to other sites in this stanza does properly go direct, as confirmed by Fiddler and Wireshark.

  Read the article

• Munin Aggregate Graphs from several servers

  - by Sparsh Gupta

  I am using DNS round robin load balancing and have divided my total traffic onto multiple servers. Each server does around 300-400req/second but I am interested in having an aggregate graph telling me the TOTAL of all requests per second served by our architecture. Is there any way I can do this. Right now each graph in Munin comes as a separate graph as they depict things on one server. I am using configuration as follow which doesn't work doesnt work for me, does this configuration got errors? [TRAFFIC.AGGREGATED] update no requests.graph_title nGinx requests requests.graph_vlabel nGinx requests per second requests.draw LINE2 requests.graph_args --base 1000 requests.graph_category nginx requests.label req/sec requests.type DERIVE requests.min 0 requests.graph_order output requests.output.sum \ lb1.visualwebsiteoptimizer.com:nginx_request_lb1.visualwebsiteoptimizer.com_request.request \ lb3.visualwebsiteoptimizer.com:nginx_request_lb2.visualwebsiteoptimizer.com_request.request \ lb3.visualwebsiteoptimizer.com:nginx_request_lb3.visualwebsiteoptimizer.com_request.request

  Read the article

• best sql server client tool and refresh managment studio edit window ?

  - by Tony

  After using other gui tools for databases like oracle sql developer , plsql editor ..., I don't quite comfortable with sql server management studio,so I want to ask: Is there any better client tools for sql server? In management studio ,if I've already opened edit window, how to refresh the data in the window ?

  Read the article

• Good hosted sites to manage quality testing?

  - by Chirag Patel

  Basically, I would like to manage quality testing with an issue management system focused on quality testing? I can't use the typical issue management system such as Lighthouse, FogBugz because each test is written as a ticket and 20 to 30 tickets need to be duplicated (w/ no history) every time we start a quality cycle. Do any (hosted) sites exist? We're currently using a Google Spreadsheet so it can be collaboratively edited.

  Read the article

• Simulating network latency for localhost connection on Windows 7

  - by nitro2k01

  I need to simulate network latency to a program running on the local computer, connecting to a local service. Thus far I have tried dummynet (a windows build of ipfw) which I got working after some trial and error. While it generally works, I can't seem to get it to filter localhost traffic. Even after adding a rule from any to any which affects external traffic, this makes no difference for local connections. I would appreciate if anyone knows how to simulate local latency using dummynet or a different tool. The tool should be able to simulate latency generically in IP packets, (TCP and UDP) and not be protocol specific.

  Read the article

• iptables question

  - by RubyFreak

  i have a small network, with one valid IP and a firewall with 3 network interfaces (LAN, WAN, DMZ). I want to enable PAT on this valid IP to redirect http traffic to a server in my DMZ. (done) I want to enable MASQ on this ip from traffic that comes from my LAN (done) I want from my LAN as well to access my http server at DMZ. (partially) Question: in the above scenario, i cannot from my LAN, to access my http server in the DMZ, since it has the IP used by the MASQ (the only valid ip that i have). What would be the best option to solve this problem? network interfaces: eth0 (WAN) eth1 (DMZ) eth2 (LAN) /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE /sbin/iptables -A FORWARD --o eth1 -d 2.2.2.2 -p tcp --dport 80 -j ACCEPT /sbin/iptables -t nat -A PREROUTING -i eth0 -d 1.1.1.1 -p tcp --dport 80 -j DNAT --to 2.2.2.2 /sbin/iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT /sbin/iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT /sbin/iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT

  Read the article

• Is it possible to combine two internet connections to increase performance?

  - by cornjuliox

  I've got a small home network, 3 PCs plus a laptop or two when the relatives come to visit, connected to a single cable internet connection. Now, as soon as everyone starts using the 'net the performance starts to suffer and if the load is heavy enough nobody can get anything done and everyone complains. At one point it was so bad that only one of us could use it at a time. I was researching possible solutions to this problem and I heard that internet cafes that utilize 2 internet connections, possibly from different providers, and have some sort of router that allows them to split the traffic between the both of them, with online games going through one and web traffic going through another. Is this possible? What is the technical term for it, and can/should it be applied to a home network setup or is there another solution to this problem?

  Read the article

• HA Proxy and Disaster Recovery - Only access server if others are down?

  - by ben2004uk

  Why I expect this is not the best way to solve the problem, I got thinking tonight. I'm thinking about geo-locating servers. Given we have a load balancer + two servers to handle traffic in NA (North America) and one server in the EU. If the two US servers die, is it possible to get HAProxy to direct traffic automatically to the EU one. However, I don't want to use a roundrobin approach for the EU - just the two US ones. The EU should only be hit when the other two are down. Does anyone know how to configure HAProxy to do this? Thanks Ben

  Read the article

• How to open a server port outside of an OpenVPN tunnel with a pf firewall on OSX (BSD)

  - by Timbo

  I have a Mac mini that I use as a media server running XBMC and serves media from my NAS to my stereo and TV (which has been color calibrated with a Spyder3Express, happy). The Mac runs OSX 10.8.2 and the internet connection is tunneled for general privacy over OpenVPN through Tunnelblick. I believe my anonymous VPN provider pushes "redirect_gateway" to OpenVPN/Tunnelblick because when on it effectively tunnels all non-LAN traffic in- and outbound. As an unwanted side effect that also opens the boxes server ports unprotected to the outside world and bypasses my firewall-router (Netgear SRX5308). I have run nmap from outside the LAN on the VPN IP and the server ports on the mini are clearly visible and connectable. The mini has the following ports open: ssh/22, ARD/5900 and 8080+9090 for the XBMC iOS client Constellation. I also have Synology NAS which apart from LAN file serving over AFP and WebDAV only serves up an OpenVPN/1194 and a PPTP/1732 server. When outside of the LAN I connect to this from my laptop over OpenVPN and over PPTP from my iPhone. I only want to connect through AFP/548 from the mini to the NAS. The border firewall (SRX5308) just works excellently, stable and with a very high throughput when streaming from various VOD services. My connection is a 100/10 with a close to theoretical max throughput. The ruleset is as follows Inbound: PPTP/1723 Allow always to 10.0.0.40 (NAS/VPN server) from a restricted IP range >corresponding to possible cell provider range OpenVPN/1194 Allow always to 10.0.0.40 (NAS/VPN server) from any Outbound: Default outbound policy: Allow Always OpenVPN/1194 TCP Allow always from 10.0.0.40 (NAS) to a.b.8.1-a.b.8.254 (VPN provider) OpenVPN/1194 UDP Allow always to 10.0.0.40 (NAS) to a.b.8.1-a.b.8.254 (VPN provider) Block always from NAS to any On the Mini I have disabled the OSX Application Level Firewall because it throws popups which don't remember my choices from one time to another and that's annoying on a media server. Instead I run Little Snitch which controls outgoing connections nicely on an application level. I have configured the excellent OSX builtin firewall pf (from BSD) as follows pf.conf (Apple App firewall tie-ins removed) (# replaced with % to avoid formatting errors) ### macro name for external interface. eth_if = "en0" vpn_if = "tap0" ### wifi_if = "en1" ### %usb_if = "en3" ext_if = $eth_if LAN="{10.0.0.0/24}" ### General housekeeping rules ### ### Drop all blocked packets silently set block-policy drop ### all incoming traffic on external interface is normalized and fragmented ### packets are reassembled. scrub in on $ext_if all fragment reassemble scrub in on $vpn_if all fragment reassemble scrub out all ### exercise antispoofing on the external interface, but add the local ### loopback interface as an exception, to prevent services utilizing the ### local loop from being blocked accidentally. ### set skip on lo0 antispoof for $ext_if inet antispoof for $vpn_if inet ### spoofing protection for all interfaces block in quick from urpf-failed ############################# block all ### Access to the mini server over ssh/22 and remote desktop/5900 from LAN/en0 only pass in on $eth_if proto tcp from $LAN to any port {22, 5900, 8080, 9090} ### Allow all udp and icmp also, necessary for Constellation. Could be tightened. pass on $eth_if proto {udp, icmp} from $LAN to any ### Allow AFP to 10.0.0.40 (NAS) pass out on $eth_if proto tcp from any to 10.0.0.40 port 548 ### Allow OpenVPN tunnel setup over unprotected link (en0) only to VPN provider IPs ### and port ranges pass on $eth_if proto tcp from any to a.b.8.0/24 port 1194:1201 ### OpenVPN Tunnel rules. All traffic allowed out, only in to ports 4100-4110 ### Outgoing pings ok pass in on $vpn_if proto {tcp, udp} from any to any port 4100:4110 pass out on $vpn_if proto {tcp, udp, icmp} from any to any So what are my goals and what does the above setup achieve? (until you tell me otherwise :) 1) Full LAN access to the above ports on the mini/media server (including through my own VPN server) 2) All internet traffic from the mini/media server is anonymized and tunneled over VPN 3) If OpenVPN/Tunnelblick on the mini drops the connection, nothing is leaked both because of pf and the router outgoing ruleset. It can't even do a DNS lookup through the router. So what do I have to hide with all this? Nothing much really, I just got carried away trying to stop port scans through the VPN tunnel :) In any case this setup works perfectly and it is very stable. The Problem at last! I want to run a minecraft server and I installed that on a separate user account on the mini server (user=mc) to keep things partitioned. I don't want this server accessible through the anonymized VPN tunnel because there are lots more port scans and hacking attempts through that than over my regular IP and I don't trust java in general. So I added the following pf rule on the mini: ### Allow Minecraft public through user mc pass in on $eth_if proto {tcp,udp} from any to any port 24983 user mc pass out on $eth_if proto {tcp, udp} from any to any user mc And these additions on the border firewall: Inbound: Allow always TCP/UDP from any to 10.0.0.40 (NAS) Outbound: Allow always TCP port 80 from 10.0.0.40 to any (needed for online account checkups) This works fine but only when the OpenVPN/Tunnelblick tunnel is down. When up no connection is possbile to the minecraft server from outside of LAN. inside LAN is always OK. Everything else functions as intended. I believe the redirect_gateway push is close to the root of the problem, but I want to keep that specific VPN provider because of the fantastic throughput, price and service. The Solution? How can I open up the minecraft server port outside of the tunnel so it's only available over en0 not the VPN tunnel? Should I a static route? But I don't know which IPs will be connecting...stumbles How secure would to estimate this setup to be and do you have other improvements to share? I've searched extensively in the last few days to no avail...If you've read this far I bet you know the answer :)

  Read the article

• How to determine what program send the packet recorded in Wireshark?

  - by Tono Nam

  I was taking some tutorials on Wireshark in order to analyze the packets sent and received when talking to a web server for purposes of learning. When I start listening/recording packets in Wireshark, there where so many packages being recorded (700 packages per minute). Is it normal to have that much traffic if I have all the programs that will cause traffic such as all browsers, log me in, dropbox, goto meeting, etc., closed? In order to try to solve the problem I am analyzing random packets. Take for instance this filter: I just selected a random IP: 74.125.130.99. So how can I know from what program those packets where created? Also how can I get more info about that communication bwtween my computer (192.168.0.139) and that server (74.125.130.99)? I just selected a random IP from the Wireshark capture. There are also other IPs that I have no idea why they are communicating with my computer. How can I figure that out?

  Read the article

• Iptables NAT logging

  - by Gerard

  I have a box setup as a router using Iptables (masquerade), logging all network traffic. The problem: Connections from LAN IPs to WAN show fine, i.e. SRC=192.168.32.10 - DST=60.242.67.190 but for traffic coming from WAN to LAN it will show the WAN IP as the source, but the routers IP as the destination, then the router - LAN IP. I.e. SRC=60.242.67.190 - DST=192.168.32.199 SRC=192.168.32.199(router) - DST=192.168.32.10 How do I configure it so that it logs the conversations correctly? SRC=192.168.32.10 - DST=60.242.67.190 SRC=60.242.67.190 DST=192.168.32.10 Any help appreciated, cheers

  Read the article

• BIG IP - HTTPS Health Monitor setup

  - by djo

  I have a Web site that we have setup a health monitoring pages so we can take our servers in and out of the Big-IP as we see fit. Now we have just moved onto Big-IP and the issue I have hit is that you setup Health Monitors for port 80 and 443, now the 80 check works fine but when I to get the 443 check to look at our file it fails. Now I am aware as I am hitting the this page on the IP address over HTTPS is going to cause a cert error but I would have guessed that BIG-Ip would have been setup just to accept the cert and carry on with the check. Is what I am wanting to do possible? Also is there a way of just using a HTTP monitor for HTTPS? Because if port 80 has stopped sending traffic then if i use the same monitor for 443 it will stop traffic to that. Any help would be great! Thanks

  Read the article

• Finding a private (NAT) host's IP using historic destination data

  - by l0c0b0x

  The issue: An unknown private (NAT) client is infected with malware and it's trying to access a Bot server at random times/dates. How we know about this: We receive bot traffic notices/alerts from REN-ISAC. Unfortunately, we don't receive those until the next day after it has happened. What they provide to us is: The source address (of the firewall) The destination addresses (it varies, but they're going to network subnet allocated to a German ISP) The source port (which varies--dynamic ports). Question: What would be the best approach to finding this internal host (historically) with a Cisco ASA as firewall? I'm guessing blocking anything to the destination address(es), and logging that type of traffic/access might allow me to find the source host, but I'm not sure which tool/command would be the most useful. I've seen Netflow thrown into a few responses when it comes to logging, but I'm confused with it's association of Logging, NAL, and nBAR, and how they relate to Netflow.

  Read the article

• Dial-in VPN Routing issue when on 192.168.x.x network range

  - by Ian

  I'm not an expert on networks but have a small office on the 192.168.x.x. range which is managed by a vigor (2800) router. I have enabled the VPN dial-in option on the router so I can get to the server on 192.168.1.100 which works fine from my macbook when i'm NOT on a local network with that is on the 192.168.x.x range. e.g. works fine when I tether over my Android smartphone but when I try & connect when on my home network, it connects, I can access the router (192.168.1.1) but cannot access 192.168.1.100 - traceroute doesn't hop via 192.168.1.1 I have enabled "send all traffic over VPN connection but again, not joy... Feels like the osx platform isn't routing the traffic out to the vpn endpoint as the destination address is on the local subnet but expect it would be. This work fine on a windows PC on the same home network. Any thoughts on what the issue could be?

  Read the article

• How to solve High Load average issue in Linux systems?

  - by RoCkStUnNeRs

  The following is the different load with cpu time in different time limit . The below output has parsed from the top command. TIME LOAD US SY NICE ID WA HI SI ST 12:02:27 208.28 4.2%us 1.0%sy 0.2%ni 93.9%id 0.7%wa 0.0%hi 0.0%si 0.0%st 12:23:22 195.48 4.2%us 1.0%sy 0.2%ni 93.9%id 0.7%wa 0.0%hi 0.0%si 0.0%st 12:34:55 199.15 4.2%us 1.0%sy 0.2%ni 93.9%id 0.7%wa 0.0%hi 0.0%si 0.0%st 13:41:50 203.66 4.2%us 1.0%sy 0.2%ni 93.8%id 0.8%wa 0.0%hi 0.0%si 0.0%st 13:42:58 278.63 4.2%us 1.0%sy 0.2%ni 93.8%id 0.8%wa 0.0%hi 0.0%si 0.0%st Following is the additional Information of the system? cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping : 10 cpu MHz : 1992.000 cache size : 6144 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 4 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr dca sse4_1 lahf_lm bogomips : 4658.69 clflush size : 64 power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping : 10 cpu MHz : 1992.000 cache size : 6144 KB physical id : 0 siblings : 4 core id : 1 cpu cores : 4 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr dca sse4_1 lahf_lm bogomips : 4655.00 clflush size : 64 power management: processor : 2 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping : 10 cpu MHz : 1992.000 cache size : 6144 KB physical id : 0 siblings : 4 core id : 2 cpu cores : 4 apicid : 2 initial apicid : 2 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr dca sse4_1 lahf_lm bogomips : 4655.00 clflush size : 64 power management: processor : 3 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping : 10 cpu MHz : 1992.000 cache size : 6144 KB physical id : 0 siblings : 4 core id : 3 cpu cores : 4 apicid : 3 initial apicid : 3 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr dca sse4_1 lahf_lm bogomips : 4654.99 clflush size : 64 power management: Memory: total used free shared buffers cached Mem: 2 1 1 0 0 0 Swap: 5 0 5 let me know why the system is getting abnormally this much high load?

  Read the article

< Previous Page | 265 266 267 268 269 270 271 272 273 274 275 276  | Next Page >