Search Results

Search found 2639 results on 106 pages for 'adam jack'.

Page 27/106 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

• Bad sound quality of 3.5mm headphone with mic on laptop

  - by Isaac

  I have a set of headphones that have a built-in mic for hands-free calling. They just work great on my Sony Ericsson Cedar cellphone. The problem is that when I connect headphone to my Dell N5010 laptop to listen to music, the quality is horrible, with very weak or no vocals. They funny part is when I hold down the talk button on the mic (headphone mic), at which point it sounds great, but goes back to bad quality as soon as I release talk button. Also, when I take out the jack a little, at some point, the sound is great but I have to hold the jack there. I looked for any configuration on the sound card driver but find nothing. Besides using a glue to hold down the talk button of mic :), is there any other solution?

  Read the article

• linksys wap54g default wpa wireless key?

  - by jack

  Hi I wrongly pressed the push button in linksys wap54g web administration. Then it restarted and stated that it's protected with WPA while I first configured it as WEP. So, my old key didn't work. What should I do? Plugin with wire cable to reconfigure it? - which is the only way? coz it was embedded in ceiling. I found no solutions in product manual and google. Thank you.

  Read the article

• Computer prints blank pages before and after content

  - by Cpt. Jack

  This would seem like a pretty simple question but I have exhausted every idea I can come up with. I bought a brand new Dell Latitude E5410 not too long ago with Windows 7 OS. I installed office 2010 on the machine right away and have had a printing problem since day one. For some reason every time I print a page, a blank page prints out before and after the content print. This also applies to any other application such as notepad or printing an email. If I have a 6 page document, it still prints out one page before and after every content page. Meaning I get my 6 page document along with 12 blank pages. I can't figure out why this would be some sort of default setting or what would cause this printing configuration. I am the only computer on the network that has this problem and quite frankly I'm getting tired of it. Can anyone help me figure this out or steer me in the right direction to correcting this problem?

  Read the article

• HDD,CD,DVD - how is sector id distinguishable from data?

  - by b-gen-jack-o-neill

  Hi, as titles says, how is sector id on HDD,CD-ROM and so distinguishable from data? I mean, when I want lets say sector #52, first, head goes to track where this sector should be, than it must wait some time to spin the desired sector above the reading head. But it must somehow recognize that its sector number, and not only data that say 52. So, how is this done? Thanks.

  Read the article

• Host wildcard subdomains using postfix.

  - by Jack M.

  I'm trying to work out how I can get postfix to accept email for any sub-domain of my main site. I don't have virtual domains, just a long list of sub-domains for local delivery. In specific, I'm feeding python@*.mydomain.com into a Python using the alias file: python: |/www/proc_email.py The Python can handle delivery from there. I envision this looking something along the lines of: mydestination = encendio, localhost.localdomain, localhost, *.mydomain.com I'm running the latest version of postfix on Ubuntu (not rightly sure how to check the version). Thanks in advance.

  Read the article

• What does the number after the IP address represent in a MySQL connection error?

  - by jack

  I'd just like to know what the number '64' represents in MySQL connection error message: Can't connect to MySQL server on '127.0.0.1' (64) in /var/www/test.php Thank you.

  Read the article

• stdout and key press

  - by Jack

  Hi, when in console, if I press a key, some interrupt controller sends code of that key to CPU, which looks into some table and than represent that keypress by printing some charracter to stdout. But, is keyboard sending an ASCII code of that key, or just some standardised code? Since there is so many languages and extra characters, OS must further translate its code into some character according to user selected scheme, I guess. I ask, becouse I am from Czech Republic, and we use some characters that do not exists in standart ASCII code. So I was thinking, if I enter this character into a console, and then print it, lets say in C++ using cin and cout, and I have set locale to Czech, stdin must actually send some non-ASCII code of the character I pressed to input stream. Am I right?

  Read the article

• How CPU communicates with HW

  - by b-gen-jack-o-neill

  Good day. I am new here, but I could not find answer to my question using google, so I help I do not violate any rules. So, basically, all I want to ask is, how CPU comminucates with other HW, such as printers, Graphic card, sound card, LAN card etc. I know, that for basic system I/O, you can use BIOS interrupts. INT 10h I believe is for display output. But, what I would like to know is, what actually happens when you execute instruction int 10h. From desription of int instruction, it should jump to routine, which is stored on adress pointed by adress stored in iterrupt table. But how does this routine get into the RAM? Does BIOS save that routines to the RAM? And what actually that routine does? I mean, CPU can only acess RAM, right? So how can now acess some other HW? Is there some special instrucion for it? Or is CPU somehow connected to BIOS, and than BIOS actually does the work? And the last thing, does even OS like Windows or GNU/Linux use BIOS interrupts, or can OS acess HW directly? Thanks.

  Read the article

• Canonical representation of a class object containing a list element in XML

  - by dendini

  I see that most implementations of JAX-RS represent a class object containing a list of elements as follows (assume a class House containing a list of People) <houses> <house> <person> <name>Adam</name> </person> <person> <name>Blake</name> </person> </house> <house> </house> </houses> The result above is obtained for instance from Jersey 2 JAX-RS implementation, notice Jersey creates a wrapper class "houses" around each house, however strangely it doesn't create a wrapper class around each person! I don't feel this is a correct mapping of a list, in other words I'd feel more confortable with something like this: <houses> <house> <persons> <person> <name>Adam</name> </person> <person> <name>Blake</name> </person> </persons> </house> <house> </house> </houses> Is there any document explaining how an object should be correctly mapped apart from any opninion?

  Read the article

• Significant OS X Finder lag when listing directories/files

  - by Jack Sleight

  I'm experiencing some significant OS X finder lag, that seems to be purely an issue with Finder itself, and not the HD or any other part of OS X (I'll explain below). The lag only appears to be when listing directories/files, where I'm seeing up to twelve or so seconds of lag (the folder opens with a blank list and the spinner going in the bottom right). This happens with both the local SSD and network drives (connected via ethernet or wifi) Browsing both local and network drives in terminal and listing directories is instant I can actually browse files on my NAS from my phone over a 3G connection from the other side of the country faster than Finder can when connected to the local network (madness!) Can anyone help? Thanks.

  Read the article

• ArchBeat Link-o-Rama for December 4, 2012

  - by Bob Rhubart

  Exalogic 2.0.1 Tea Break Snippets - Creating and using Distribution Groups | The Old Toxophilist "Although in many cases we, as Cloud Users, may not be to worried how the Virtualisation Algorithm decides where to place our vServers," says The Old Toxopholist, "there are cases where it is extremely important that vServers run on distinct physical compute nodes." There's plenty more on the subject in his blog post. Oracle Endeca (2.3) Record Level Security | Adam Seed Adam Sneed's blog post covers "the basics of security within Endeca Information Discovery, as these basic security objects are required in order to explain the implementation of record level security." ODI Handling DQ | Gurcan Orhan Oracle ACE Director Gurcan Orhan suggests you have fun with these scripts for Oracle Data Integrator. Parleys Testimonial at GlassFish Community Event - JavaOne 2012 Video of Parley's webmaster Stephan Janssen's presentation at the GlassFish Community Event at JavaOne 2012, in which he explains why Parley's moved from Tomcat to GlassFish. Java Spotlight Episode 109: Pete Muir on CDI 1.1 This edition of Roger Brinkley's Java Spotlight Podcast features an interview with CDI 1.1 spec lead Pete Muir of JBoss/Red Hat. Muir talks about the features in CDI 1.1 and what to expect in the future. Webcast: Java Management Extensions with Oracle WebLogic Server 12c Dr. Frank Munz and Dave Cabelus do the talking in this on-demand webcast focused on Oracle WebLogic Server 12c with Java Management Extensions (JMX). Using the Coherence API to get Portable Object Format bytes | Bruno Borges Bruno Borges shares a code snippet that illustrates how easy it is to use the Coherence API. Thought for the Day "Experience is something you don't get until just after you need it." — Anonymous Source: SoftwareQuotes.com

  Read the article

• Windows powering off after "preparing your desktop" stage.

  - by Jack

  Windows 7 64 bit. The only recent change was I installed two updates for MS Office, and a cumulative security update for IE. As soon as I choose a user and login, after loading my user profile it states the preparing your desktop message, and then powers off. I have used DaRT to check the event log, but nothing is recorded. Ideas?

  Read the article

• [SOLVED] vmware problems - networking - no packet response

  - by jack

  XP is my host. Ubuntu is my Guest in VMware. When I do the following commands, I should get SMTP respones but now get no response. I use wireshark to analayze it. Also in wireshark shows nothing. root@vmware:~# netcat 192.168.1.2 25 220 762462a8c4d Microsoft ESMTP MAIL Service, Version: 6.0.2600.5949 ready at Fri, 12 May 2010 18:04:20 +0800 EHLO SAYHELLO VRFY TEST@LOCALHOST test \ sdfsafsd How can I fix it? UPDATE: I came to know that this is no VMWare problem. This is Netcat problem. For this, you might have to type Ctrl+M {ENTER} {ENTER}

  Read the article

• File server share access intermittent/slow/machine unstable: win2k8r2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• Windows powering off after login

  - by Jack

  As soon as I logon to Windows 7 64bit, the computer restarts. It isn't a hardware issue, as linux works fine. Windows 7 64 bit. Safe mode, last known good configuration etc, nothing makes any difference. Nor does startup repair or sfc. I used DaRT to check the event log, and nothing is recorded. How can I troubleshoot this?

  Read the article

• In Linux, how to ls -l a directory and not the contents of that directory?

  - by Jack

  For example, if I have a directory containing files file1 and file2, and a directory dir1, then "ls -l file1" will show details just for file1. Doing the same thing for dir1 will instead show the contents of dir1. Is there a way to treat dir1 like file1?

  Read the article

• Technicolor TG582n with external DHCP server [on hold]

  - by Jack

  We have a small home setup with a Technicolor TG582n on Plusnet ISP. We have a Samba4 DC with DNS forwarding enabled. The DC forwards to the Technicolor. However, the client machines have their DNS settings manually set. This is an annoyance when using laptops on other networks. We would like to have DHCP handled on the server machine, such that when a client connects to the Technicolor, it gets its IP and DNS information from the DHCP server, eliminating the need to manually set adapter DNS settings. However, I cannot find an option to disable DHCP on the Technicolor and am not completely clear on how one would point DHCP services to the server from the Technicolor if there were the option. So, how would one make the Technicolor use an external server for DHCP leases?

  Read the article

• How does an OS communicate with other hardware components?

  - by Jack

  How can a program running on a CPU (mostly OS) access other PC hardware? Such as Graphic card, HDD and so? From what I read, in DOS, this was done using BIOS calls, specifically the INT instruction. But, the INT instruction should only jump to the certain space in RAM. So how can some program stored in RAM access other computer hardware, when the CPU can only access RAM, and receive interrupts? Does Windows use INT instructions as well, or is there a new way to communicate with the hardware?

  Read the article

• Forcing Acrobat Reader font

  - by Jack

  Hello, I have a netbook with Linpus Linux and I'm trying to open automatically generated documents with Acrobat Reader that use Verdana but without having it embedded inside the PDF file. Linpus doesn't come natively with any Verdana font so I had to install them inside /usr/share/fonts/by doing mkfontdirand fc-cacheto force a recache of the fonts. Then I've been able to select it inside other programs (eg. OpenOffice) but I'm still unable to open these PDFs. It seems that Acrobat is unable to find the font anyway. Since I have no control on how these PDFs are generated, is there a way to force Acrobat to use a specific font is the one it needs is unfound? Or maybe Acrobat needs a different kind of font configuration on Linux? Thanks in advance

  Read the article

• x86 exceptions and flags

  - by b-gen-jack-o-neill

  Hi, please, I know that when you for example divide by zero, the aproptiate flag is set in CPU flag register. But today I read that there are special interrupt vectors (I think the first 16 in IVT) that are used for such conditions like dividing by zero. So, what I want to ask is, does any situation that couses change som flag also triggers apropriate interrupt? Becouse in school, we used conditional jumps that checks wheather carry flag has been set or not, and I don´t remember there was some interrupt triggerd by that. So I am pretty confused now.

  Read the article

• wusa in server 2008 R2

  - by Jack

  I need to use wusa to uninstall a particular update that is causing a reboot loop. I can access winre and dism, but wusa gives command not found. Does wusa not come with r2, or is it not available in the built-in WinRE or what?

  Read the article

• Download from http server all directories,files and subdirectories and so on

  - by Jack

  I want to download from remote http server all files directories,files and so on. I found some solutions to ftp server,but doesn't work to http. Until now no luck with wget -r or -m. It download all direcotories in the root and the respective index.html. Not all files and sub-directory under such it(note the sub-directory may have another directory and so on) not sure on tags fix for me if needs. Note: I'm not a native english speaker,sorry for bad english.

  Read the article

• Need to use wusa to stop endless rebooting on R2

  - by Jack

  I installed 3 updates, which after rebooting resulted in a reboot loop, never going past the "configuring your computer for windows" stage. Last known good configuration, safe mode etc make no difference (as expected). I have no system restore images available. I used dism to uninstall one of the updates, but the other two appear to be MSP patches, and so I cannot use dism to uninstall them. From what I have been reading it appears I must use wusa, however wusa does not seem to be included in WinRE. Does anyone have a suggestion of how I can access wusa to uninstall these updates, and hopefully reverse this problem?

  Read the article

• what does the number represents in MYSQL connection error

  - by jack

  Hi I'd just like to know what the number '64' represents in mysql connection error message: Can't connect to MySQL server on '127.0.0.1' (64) in /var/www/test.php Thank you.

  Read the article

• nginx doesn't find the directory but apache does

  - by Jack Spairow

  I use apache as the backend server and nginx on the frontend. Apache listens to port 8080 and nginx to port 80. What I do is have the root point to the public folder foreach virtualhost: <VirtualHost *:8080> ServerAdmin webmaster@localhost ServerName site.com ServerAlias site.com *.site.com DocumentRoot /var/www/site.com/public <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/site.com/public/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> </VirtualHost> And here's the nginx config: server { listen 80; access_log /var/log/nginx.access.log; error_log /var/log/nginx.error.log; root /var/www/site.com/public; index index.php index.html; server_name site.com *.site.com; location / { location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $host; proxy_pass http://127.0.0.1:8080; proxy_cache one; proxy_cache_use_stale error timeout invalid_header updating; proxy_cache_key $scheme$host$request_uri; proxy_cache_valid 200 301 302 20m; proxy_cache_valid 404 1m; proxy_cache_valid any 15m; } } location ~ /\.(ht|git) { deny all; } } The problem is Apache resolves the domain just fine (site.com:8080), but nginx shows instead a 502 Bad Gateway (site.com:80). I tried looking at the error_log and access_log but I can't find any hint for why can't nginx work. EDIT: The problem was I wasn't able to include that isolated config for nginx.

  Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >