Search Results

Search found 27649 results on 1106 pages for 'ask how to geek'.

Page 270/1106 | < Previous Page | 266 267 268 269 270 271 272 273 274 275 276 277  | Next Page >

• Cannot connect to secure wireless with Netgear wna3100 USB

  - by Vince Radice

  I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

  Read the article

• How to make Windows boot first?

  - by Rani.Shemer

  I want to know how to make Windows the default boot OS in Ubuntu 11.10, how to make Windows boot first on GRUB2, specifically for Windows 7, which is my current version. I know that are some tutorials about this, but it seems that I made a mistake, so I'm asking. Luckily nothing serious happened. I didn't lose my data. The difference between my question and the tutorials is that the tutorials are from older version. Sorry for any disturbs and redundancy of the question. I'll love it better for a GUI app that making easy the boot. P.S: I forgot to say the version of my OS's I am running Windows 7 Home Premium X64 bit Ubuntu 11.10 X64 bit I hope this will make understand better because I now saw it a tutorial that for 64 bit versions Startup-Manager doesn't work.

  Read the article

• Is there a IRC Client which can use or emulate mIRC scripts

  - by fred.bear

  I've used mIRC (Windows) for years, and have some custom scripts, written in mIRC's own scripting language. Is there an Ubuntu/Linux IRC Client which will allow me to use my scripts as-is? Failing that, is there a "functions a lot like mIRC" Client available? I've just tried Pidgin's IRC client, but it seems to be quite basic. I couldn't see any way for it to tap into channel activity via scripts. I don't want to use Wine... WineHQ reports it as having too many bugs for my liking, and anyhow, I try to avoid using Wine like I do Windows :)

  Read the article

• SSH'ing to my machine attaches an existing screen session and detaching it ends my SSH session

  - by jsplaine

  ssh'ing to my Ubuntu machine automatically attaches an existing screen session and detaching ends my ssh session What I want is to be able to ssh to my Ubuntu machine without automatically attaching to the screen session on that machine. Or at least, I should be able to to detach from that screen session w/o ending my ssh session .. right? Doesn't seem to work. This so that I can attempt to run firefox --display <whichever one is being forwarded to my ssh session>, so that I can debug a website that the remote Ubuntu machine is running (via localhost). Best case scenario is that I could just remote-desktop to my Ubuntu machine. But it's not set up to allow remote-desktop, and I see no way to set it up remotely via shell/ssh. Also, it sounds like you need a static IP in order to remote desktop to an Ubuntu machine (so I keep reading).

  Read the article

• Cannot access system after deleting passwd file

  - by joao rodrigo leao

  I was trying to change my user name and also my /home/username and my system started to crash. I deleted the passwd file but I had a backup named passwd_bkp. I tried to rename this passwd_bkp as passwd and it did not work. No commands were being executed... I was in a terminal window. I re-started my system and now I cannot login. The GRub loads two options: Linux and recovery mode. I tried to open a sessions as root but it says the file system is corrupted. I cannot access my files. Did I lose all my files?

  Read the article

• Not getting GUI mode on ubuntu 12.04 desktop edition after installation on vmware workstation 7

  - by Salil Naik

  I installed Ubuntu 12.04 desktop edition on my PC using VMWare workstation 7. I assigned 1GB RAM and 20 GB Hard disk to Ubuntu. While starting Ubuntu virtual machine, It is not starting up with GUI mode. In is prompting me my Login ID in textual mode always. After waiting for long time as well the GUI mode is not appearing. I tried running sudo apt-get install updates sudo apt-get install xinit sudo apt-get install ubuntu-desktop Honestly, i don't know the meaning of all these.I am very new to ubuntu.Please help me here what to do? Below is my Laptop configuration OS: Genuine Windows 7 Home Basic(64 bit) RAM: 3 GB Processor: Intel core i3 Regards Salil

  Read the article

• How to fix the apt-get -f install error [duplicate]

  - by Satish Patel

  This question already has an answer here: How do I fix a “Could not get lock /var/lib/dpkg/lock” problem? 12 answers I am getting continuous error when I run the command sudo apt-get -f install The output of the command is as follows: Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: default-jre-headless icedtea-7-jre-jamvm openjdk-7-jre openjdk-7-jre-headless openjdk-7-jre-lib Suggested packages: fonts-ipafont-gothic fonts-ipafont-mincho ttf-telugu-fonts ttf-oriya-fonts ttf-kannada-fonts ttf-bengali-fonts The following NEW packages will be installed: default-jre-headless icedtea-7-jre-jamvm openjdk-7-jre openjdk-7-jre-headless openjdk-7-jre-lib 0 upgraded, 5 newly installed, 0 to remove and 28 not upgraded. 2 not fully installed or removed E: Could not get lock /var/cache/apt/archives/lock - open (11: Resource temporarily unavailable) E: Unable to lock directory /var/cache/apt/archives/ satish@satish-Inspiron-N5010 ~ $ please guide ASAP

  Read the article

• Need a PCIe desktop graphics card for dual-monitor

  - by Graham

  I have a mid-2008 workstation with two HD monitors supporting HDMI and DVI inputs. Since Ubuntu 11.10, I have experienced no end of trouble with my NVidia Quadro NVS 290 in TwinView dual-monitor output. Others have similar desktop TwinView woes. I want a new graphics card. Previously I asked for a graphics card recommendation and response was Nvidia Geforce GTS 450... but really I'm looking for someone who has actually got a working dual-monitor desktop to tell me what card they use so I can get something that is known to work. So please, people who have no-issues with their 64-bit Ubuntu 12.04 Unity 3D desktop spread across two HD-resolution external monitors (either DVI or HDMI connector), and who also run Google Chrome (which throws a spanner due to its own GPU compositing)... please let me know what graphics card you have so I can buy one. Gathering Options These seem to be the Nvidia cards featuring dual DVI. But they all seem to be gaming cards - what has dual-DVI, good support, but is not a massive gaming card? Nvidia GTS 450 (previously recommended) - 2x DVI Nvidia GTX 550 Ti (used by System76) - 2x DVI Nvidia GT 430 (used by System76) - 1xDVI, 1xHDMI Nvidia GT 640 (found on NVidia site) - 1xDVI, 1xHDMI (also GT 620, GT 630) Has anyone had a good desktop dual-monitor Unity 3D experience with ATI cards?

  Read the article

• Setting different default applications for different Desktop Environment

  - by Anwar

  I am using Ubuntu 12.04 with default Unity interface. I installed later the KDE desktop, XFCE, LXDE, gnome-shell and Cinnamon. The KDE comes with different default applications than Unity, such as kwrite for text editing, konsole as virtual terminal, kfontview for font viewing and installing, dolphin as File browser etc. Other DE come with some other default applications. The problem arises when you want to open a file such as a text file, with which can both be opened by gedit and kwrite, I want to use kwrite on KDE and gedit on Unity or Gnome. But, there is no way to set like this. I can set default application for text file by changing respective settings in both KDE and Unity, but It become default for both DE. For example, If I set kfontviewer as default font viewing application in KDE, it also opens fonts when I am in Unity or Gnome and vice versa. This is a problem because, loading other DE's program takes long time than the default one for the used DE. My question is: Can I use different default applications for different DE? How?

  Read the article

• How to get SRGP working?

  - by Bo Tian

  I'm running 64-bit Ubuntu 10.10, and I'm trying to make SRGP work. SRGP is an old graphics package that accompanies the book "Computer Graphics" by Foley, van Dam, et al. I have installed libx11-dev, but I still can't get through make. I get the error "cannot find -lsrgp" when I typed make PROG=show_pattern. Full compilation messages are here http://pastebin.com/CWuw4xte What do I have to do to get it working?

  Read the article

• How Can I Get My USB TV Tuner To Work

  - by Foxface

  I have a KWorld UB445-U ATSC Hybrid TV Stick. I've tried MythTV, but it kept crashing when I was trying to set it up, and didn't get anywhere with it. I've tried VLC and just tried Kaffiene. I'm not sure how to work VLC or Kaffeine to accept my TV. Can someone help me with it? EDIT: Code: foxface@Toshiba-Satellite-L775:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b289 Chicony Electronics Co., Ltd Bus 002 Device 006: ID 1b80:e421 Afatech Bus 003 Device 002: ID 13fd:1e40 Initio Corporation

  Read the article

• Install squid3 + and eCAP module

  - by Hacker

  I want to install squid3 and eCAP module on my latest ubuntu. Squid installed well with command i followed these instructions. http://e-healthexpert.org/node/431 sudo apt-get install squid3 but how do i configure it to enable eCAP module ?. I need to give something like --enable-ecap option while installation, which i could not. Then i tried to manually install using http://code.google.com/p/squid-ecap-gzip/source/browse/wiki/Installation.wiki?r=24 but while installing squid3 it gives error. i.e. command sudo make gives some g++ error. SO how do i install it and configure for eCAP. please h

  Read the article

• How do I ban a wifi network in Network Manager?

  - by Chris Conway

  My wifi connection drops sometimes and, for some reason, Network Manager attempts to connect to my neighbor's network, which requires a password that I don't know. The network in question is not listed in the "Edit Connections..." dialog and I can find no reference to it in any configuration file, but still the password dialog pops up every time my main connection drops. Is there a way to blacklist a wireless network so that the Network Manager will never attempt to connect to it? Or, equivalently, how can I remove the configuration data that causes the Network Manager to attempt to connect to this particular network?

  Read the article

• Acer Wireless Network not working

  - by pico

  I installed Ubuntu 12.04 64 Bit desktop version in acer AspireE1-470. Everything work great except Wireless and touch pad. When i run additional driver there nothing to activate and when i run "rfkill list" it's show 0: hci0:bluetooth Soft blocked: yes Hard Blocked: no 1: acer-wireless: Wireless Lan Soft blocked: no Hard blocked: no I don't know too much command in linux and i hv no i ieda hot to work wireless and touch-pad

  Read the article

• USB3 boot device disappears post-grub

  - by JoBu1324

  I have an installation of Ubuntu 12.10 on a USB3 device, and it occasionally disappears during boot, dropping me into busybox. This is what I've been able to figure out so far: During a single boot, the following happened: At the grub2 menu, I typed c and dropped to the grub> prompt I typed ls -l and got a list of all the devices, including partitions and UUIDs - the USB3 partitions were available I escaped back to the boot select menu, selected the default item (ubuntu) and hit enter The screen went black for a second before turning into the purple Ubuntu boot screen with the dots (which usually indicates that the boot will fail. When all is well I don't get the black screen) The boot dropped into BusyBox v1.19.3 with the message `ALERT! /dev/disk/by-uuid/[uuid] does not exist blkid displays all of the partitions except those of the USB3 device, as does ls /dev/disk/by-uuid or any of the alternatives.

  Read the article

• Netflix Updates Android Tablet App; iPad Update On The Way

  - by Jason Fitzpatrick

  Android: If you’re rocking an Android tablet, such as a Kindle Fire or Nook, you’ll want to update your Netflix app today. The new version sports a host of improvements including a massively overhauled interface. The old Netflix tablet application was functional but lackluster; it felt almost as if they didn’t realize they were designing it for a tablet. The new Netflix app is focused on beautiful cover-flow style navigation, displaying twice as many titles per screen, and an emphasis on natural navigation with finger swipes and taps. According to the Netflix press release, an iPad update will be rolling out in the next few weeks. New Experience Now Available for All Android Tablets [Netflix Blog] How to Run Android Apps on Your Desktop the Easy Way HTG Explains: Do You Really Need to Defrag Your PC? Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone

  Read the article

• Add Custom Launcher in 11.10

  - by sayth

  I started by searching guides. I found this guide but neither of the main methods works anymore in 11.10. The first solution, I have created the desktop file, however the file location given as .gconf-> desktop-> unity-> launcher -> favourites no longer exists. I can get to /home/sayth/.gconf/desktop but there is no longer a unity folder. The second solution described right-clicking the desktop and creating a launcher. Right-clicking the desktop no longer produces a "create a launcher" option. I manually installed geany 0.21 as the one in the repo's is outdated. It's installed and working correctly, and is executing from /usr/local/bin/geany. How can I add it to the launcher?

  Read the article

• What is an elegant way to install non-repository software in 12.04?

  - by Tomas

  Perhaps I missed something when Canonical removed the "Create launcher" option from the right click menu, because I've really been missing that little guy. For me, it was the preferred way to install software that comes not in a .deb, but in a tar.gz, for example. (Note: in that tar.gz I have a folder with the compiled files, I'm NOT compiling from source) I just downloaded the new Eclipse IDE and extracted the tar.gz to my /usr folder. Now, I'd like to add it to my desktop and dash so it can be started easily. Intuitively I would right click the desktop and create a launcher. After this I'd copy the .desktop to /usr/share/applications. However, creating a launcher is not possible. My question: How would you install an already compiled tar.gz that you have downloaded from the internet? Below are a few things I've seen, but these are all more time-consuming than the right click option. If you have any better ideas, please let me know. Thanks! Manual copy & create a .desktop file: manually Simply extract the archive to /usr. Create a new text file, adding something along the lines of the code block below: [Desktop Entry] Version=1.0 Type=Application Terminal=false Exec="/usr/local/eclipse42/eclipse" Name="Eclipse 4.2" Icon=/home/tomas/icons/eclipse.svg Rename this file to eclipse42.desktop and make it executable. Then copy this to /usr/share/applications. Manually copy & create a .desktop file: GUI fossfreedom has elaborated on this in How can I create launchers on my desktop? Basically it involves the command: gnome-desktop-item-edit --create-new ~/Desktop After creating the launcher, copy it to /usr/share/applications.

  Read the article

• Can I use my computer as an A2DP receiver?

  - by Pierre-Yves Gillier

  First, the problem: I'm using a Cowon MP3 player as my main music player with basic earplugs. It offers A2DP & I'd like to have my netbook (running UNE 10.04) act as receiver. Some resources on the web about a2dp, but most are out of date: http://fosswire.com/post/2008/10/better-bluetooth-audio/ http://jprvita.wordpress.com/2009/12/15/1-2-3-4-a2dp-stream/ http://dpillay.wordpress.com/2010/09/27/ubuntu-10-04-a2dp-awesome-headset-music/

  Read the article

• Error installing MySQL Ubuntu 12.04, dependency?

  - by user86736

  I'm trying to install MySQL 5.5 on Ubuntu 12.04, but I'm stuck with this error: Setting up mysql-server-5.5 (5.5.24-0ubuntu0.12.04.1) ... start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.5; however: Package mysql-server-5.5 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: mysql-server-5.5 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1) Thanks for help!

  Read the article

• Which tool to use for "home banking"?

  - by Huygens

  I would like to manage my bank accounts in a secure manner on Ubuntu. I saw several applications in the Software Centre, but I don't know which one to choose. I don't need fancy features like stock options. I just have regular accounts which I want to follow, I don't want complicated stuff. As bank data are quite sensitive, I would highly prefer an application that does encryption of the data. Though, if you have a really cool app but it does not have this feature, as long as it offers to store the data in one dedicated place, I could do with encrypting that place. So what tool do you use that could fit my needs?

  Read the article

• Thunderbird 16 and Lightning

  - by Kim

  I have just upgraded from Thunderbird 15 to 16 and then found that Lightning 1.7 is not compatible with Thunderbird 16, leaving me without a calendar. What are my options? Should I try and go back to Thunderbird 15 or is there someway of finding a version of Lightning that is compatible with Thunderbird 16? I need to have a working calender and have been happily using Lightning for many years. I am using Ubuntu 12.04 (precise) 32-bit if that is any help

  Read the article

• Ignore "Bad: new and old password are too similar"

  - by user999

  I receive this message when trying to change my password: "Bad: new and old password are too similar" The passwords' "similarity" is irrelevant for my needs, so I'd like to bypass this. I tried sudo passwd $my_username I thought this had worked because I got a message: passwd: password updated successfully However, the password change has no effect after leaving the terminal, and my old password is still the only one recognized. Any ideas? thanks

  Read the article

• Ubuntu 10.10 Network Issues (wireless as well as wired)

  - by user9054

  down vote favorite Hi Friends, I have got this issue with Ubuntu 10.10 . I have been with ubuntu 8.04 and then decided to try out ubuntu 10.10 . I booted with a LiveCD and was able to configure the wireless network painlessly using the livecd . so happily i installed ubuntu 10.10 . As soon as ubuntu came up it detected the wireless network and i was able to assign a static IP to eth1 (i dont use DHCP option on my ADSL router) and enter a wap key and use pppoeconf to configure the dialer . The net was on and i was able to surf the net . all hunky dory so far . However on the next boot the fun started . It did not detect the wireless network . I could not see the network manager icon in the systray . I used ifconfig and saw that the entry for eth1 was missing .I used ifup eth1 and it said that eth1 was already up . Then i installed wifi-radar . Wifi-Radar detected the wireless network . I configured wifi-radar for the detected wireless network , set the wap driver as wext and used the manual IP settings . However on clicking connect wifi-radar started looking for a DHCP IP , needless to say it failed . For the love of god i cannot understand why wifi-radar is using DHCP when i have specified manual settings . Next i decided to use the wired network to surf the net looking for a solution . So i plugged in the network cable from my modem , it detected the plugged in connection , i configured eth0 , used pppoeconf and connected to the net . Then i foolishly decided to reboot my PC . And wonders of wonders , the same problem appeared . I cannot see eth0 in my ifconfig anymore . i used pon to start the dsl-provider connection and it said something about network error or something . Now my ifconfig shows only lo , both eth0 and eth1 have disappeared .Can anybody help me on this ? Is it a problem with ipv6 , if so how do you disable ipv6 on ubuntu 10.10 ? OR is this is a known issue with ubuntu 10.10 ? .PS : 1) i tried linux mint 10 and had the same issue . on rebooting wireless network was not getting detected . 2) i have made myself the administrator so that there is no issue of rights or anything. Any help is appreciated.

  Read the article

• I have a ESXi 5.0 installed and when I am Installing Ubuntu Server 12.04 LTS it is giving an error saying grub installation failed?

  - by Rishee

  I have a ESXi 5.0 installed and when I am Installing Ubuntu Server 12.04 LTS (32 bit) it is giving an error saying grub installation failed? Please check the below screenshot of the error. I have other Ubuntu servers running fine on this esxi server, so I don't think problem is with ESXi. I have 32 GB of ram spare on this ESXi and have given 2 GB of RAM to this 12.0 LTS VM. I have given 2 cores of processor. I have tried supplying different ISO Image to this VM as I thought the 1st image that I downloaded has errors.. But defiantly that's not the case as all 3 different ISO images that I downloaded of Ubuntu server 12.04 LTS (32-bit) can't be corrupt!! Just to make sure that the Image does not have problem I used that Image to install it for testing on stand alone system. it works fine there!! This is a production ESXi server with which I can't play with, how ever I can play whith the Ubuntu Server 12.04 LTS (32-Bit) VM that we have created on that ESXi. I need help on this as soon as possible. go live date of this server is really close. (This Question is already there on Super user and Server Fault.)

  Read the article

< Previous Page | 266 267 268 269 270 271 272 273 274 275 276 277  | Next Page >