Search Results

Search found 10931 results on 438 pages for 'struts config'.

Page 270/438 | < Previous Page | 266 267 268 269 270 271 272 273 274 275 276 277 | Next Page >

Sound card not detected in 13.04

- by Ganessh Kumar R P

I have a problem with my sound card. I don't have volume up or down option anywhere. In the setting -> Sound I don't have any card detected. But when I run the command sudo aplay -l, I get the following output **** List of PLAYBACK Hardware Devices **** Failed to create secure directory (/home/ganessh/.config/pulse): Permission denied card 0: MID [HDA Intel MID], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 And the command lspci -v | grep -A7 -i "audio" outputs 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at f0f20000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) (prog-if 00 [Normal decode]) -- 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d3efc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 So, I assume that the drivers are properly installed but still I don't get any option in the settings or volume control. The same card used to work well back in 2010 versions(04 and 10) Any help is appreciated. Thanks

Read the article
HP Envy dv6t-7300: Disabled WiFi through button and can't enable it anymore

- by Mateus B. Cassiano

Well, I have a HP Envy dv6t-7300 laptop that came with a Ralink RT5390 WiFi card. Everything was working perfectly, and eventually I press the WiFi button in my keyboard to toggle the card on/off. Until today, all worked right: if the wifi was off (wifi LED amber) and I press the wifi button, after a few seconds the LED turn white and everything works. If I repeat the process, the wifi LED turn amber and the card get disabled, but now, I can't turn it on anymore. running sudo rfkill list all I get: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes So, I ran sudo rfkill unblock all but nothing changed. As a side note, if I run sudo ifconfig wlan0 up, the indicator LED gets white (indicating that the card was enabled), but Ubuntu still say that the card is blocked by hardware. Extra information: the card works without issues in windows and in Ubuntu installer (booting from a live CD). I'm using the card out-of-box, using the drivers already included in Ubuntu 12.10. The module rt2800pci is loaded and working fine, not blacklisted, etc, etc. The card and the button toggle worked flawlessly until today, when I toggled it off and can't turn it on anymore... The problem is back, but in a different manner: if I don't press the wifi key a few times during the grub loading, in the login screen the wifi button will be ambar (disabled), pressing it will toggle it white (enabled) or ambar (disabled) again, but ubuntu still says that the network card was disabled by hardware and doesn't connect... In other words, if I don't press the WiFi button a few times when Ubuntu is booting, it will be stuck with the "network card was disabled by hardware" message, even if the light is white (enabled). Any clue? Maybe a error in some startup script or config file?

Read the article
Dual booted Windows 7 freezes after login screen

- by Cathal

First-time Linux user, using a Packard Bell Easy Note TS laptop. My problem arose after I dual boot installed Ubuntu 12.04 on Windows 7 via WUBI. I backed up all my data, and reinstalled Windows from factory settings on the recovery partition. When I first tried to install Ubuntu I mistakenly closed the lid at the start of the installation, stopping it. After that I rebooted, and my second installation attempt went without a hitch. Ubuntu works perfectly, the data on the partitions seem to be fine. My problem is I can't log back in to Windows 7. After selecting it in GRUB, and then in the Windows 7/ WUBI choice on boot, it loads up perfectly til the user log in screen. After the password is inputted, it stalls on the "Welcome" busy screen. This happens in Safe mode as well. Startup repair can't find a problem and neither can CHKDSK. System restore and Last known good config have no effect either. If anyone could help me out, I'd be real grateful. edit in response to the question below, since I don't know how to comment: Windows was installed first and its partitions are the first on the list. Should I move the windows partitions to after the Linux ones on the disk? Thanks for your help.

Read the article
Limiting calls to WCF services from BizTalk

- by IntegrationOverload

** WORK IN PROGRESS ** This is just a placeholder for the full article that is in progress. The problem My BTS solution was receiving thousands of messages at once. After processing by BTS I needed to send them on via one of several WCF services depending on the message content. The problem is that due to the asynchronous nature of BizTalk the WCF services were getting hammered and could not cope with the load. Note: It is possible to limit the SOAP calls in the BtsNtSvc.exe.Config file but that does not have the desired results for Net-TCP WCF services. The solution So I created a new MessageType for the messages in question and posted them to the BTS messaeg box. This schema included the URL they were being sent to as a promoted property. I then subscribed to the message type from a new orchestraton (that does just the WCF send) using the URL as a correlation ID. This created a singleton orchestraton that was instantiated when the first message hit the message box. It then waits for further messages with the same correlation ID and type and processs them one at a time using a loop shape with a timer (A pretty standard pattern for processing related messages) Image to go here This limits the number of calls to the individual WCF services to 1. Which is a good start but the service can handle more than that and I didn't want to create a bottleneck. So I then constructed the Correlation ID using the URL concatinated with a random number between 1 and 10. This makes 10 possible correlation IDs per URL and so 10 instances of the singleton Orchestration per WCF service. Just what I needed and the upper random number is a configuration value in SSO so I can change the maximum connections without touching the code.

Read the article
Passing Parameters to an ADF Page through the URL - Part 2.

- by shay.shmeltzer

I showed before how to pass a parameter on the URL when invoking a taskflow (where the taskflow starts with a method call and then a page). However in some simpler scenarios you don't actually need a full blown taskflow. Instead you can use page level parameters defined for your page in the adfc-config.xml file. So below is a demo of this technique. I'm also taking advantage of this video to show the concept of a view object level service method and how to invoke it from your page. P.S. You might wonder - why not just reference #{param.amount} as the value set for the method parameter? Why do I need to copy it into a viewScope parameter? The advantage of placing the value in the viewScope is that it is available even when the page went through several sumbits. For example if you switch the "partialSumbit" property of the "Next" button to false in the above example - the minute that you press the button to go to the next department - the param.amount value is gone. However the ViewScope is still there as long as you stay on this page.

Read the article
Weird 302 Redirects in Windows Azure

- by Your DisplayName here!

In IdentityServer I don’t use Forms Authentication but the session facility from WIF. That also means that I implemented my own redirect logic to a login page when needed. To achieve that I turned off the built-in authentication (authenticationMode="none") and added an Application_EndRequest handler that checks for 401s and does the redirect to my sign in route. The redirect only happens for web pages and not for web services. This all works fine in local IIS – but in the Azure Compute Emulator and Windows Azure many of my tests are failing and I suddenly see 302 status codes where I expected 401s (the web service calls). After some debugging kung-fu and enabling FREB I found out, that there is still the Forms Authentication module in effect turning 401s into 302s. My EndRequest handler never sees a 401 (despite turning forms auth off in config)! Not sure what’s going on (I suspect some inherited configuration that gets in my way here). Even if it shouldn’t be necessary, an explicit removal of the forms auth module from the module list fixed it, and I now have the same behavior in local IIS and Windows Azure. strange. <modules> <remove name="FormsAuthentication" /> </modules> HTH Update: Brock ran into the same issue, and found the real reason. Read here.

Read the article
How To Export/Import a Website in IIS 7.x

- by Tray Harrison

IIS 6 had a great feature called ‘Save Configuration to a File’ which would allow you to easily export a website’s configuration, to be later used to import either on the same server or another box. This came in handy anytime you wanted to duplicate a site in order to do some testing without impacting the existing application. So naturally, Microsoft decided to do away with this feature in IIS 7. The process to export/import a site is still fairly simple, though not as obvious as it was in previous versions. Here are the steps: 1. Open a command prompt and navigate to C:\Windows\System32\inetsrv and run the following command: appcmd list site /name:<sitename> /config /xml > C:\output.xml So if you were wanting to export a website named EAC, you would run the following: If you’ll be setting up another copy of the site on the same server, you’ll now need to edit the output.xml file before importing it. This is necessary in order to avoid conflicts such as bindings, Site ID, etc. To do this, edit the XML and change the values. Go ahead and make a copy of the home directory, and rename it to whatever folder name you specified in the output – /EAC2 in this example. If you decide to change the app pool, make sure you go ahead and create the new app pool as well. Once these edits have been made, we are now ready to import the site. To do that run: appcmd add sites /in < c:\output.xml So for our example it would look like this: That’s it. You should now see your site listed when opening up Inet Manager. If for some reason the site fails to start, that’s probably because you forgot to create the new app pool or there is a problem with one of the other parameters you changed. Look at the System log to identify any issues like this.

Read the article
WCF REST Error Handler

- by Elton Stoneman

I’ve put up on GitHub a sample WCF error handler for REST services, which returns proper HTTP status codes in response to service errors. The code is very simple – a ServiceBehavior implementation which can be specified in config to tag the RestErrorHandler to a service. Any uncaught exceptions will be routed to the error handler, which sets the HTTP status code and description in the response, based on the type of exception. The sample defines a ClientException which can be thrown in code to indicate a problem with the client’s request, and the response will be a status 400 with a friendly error message: throw new ClientException("Invalid userId. Must be provided as a positive integer"); - responds: Request URL http://localhost/Sixeyed.WcfRestErrorHandler.Sample/ErrorProneService.svc/lastLogin?userId=xyz Error Status Code: 400, Description: Invalid userId. Must be provided as a positive integer Any other uncaught exceptions are hidden from the client. The full details are logged with a GUID to identify the error, and the response to the client is a status 500 with a generic message giving them the GUID to follow up on: var iUserId = 0; var dbz = 1 / iUserId; - logs the divide-by-zero error and responds: Request URL http://localhost/Sixeyed.WcfRestErrorHandler.Sample/ErrorProneService.svc/dbz Error Status Code: 500, Description: Something has gone wrong. Please contact our support team with helpdesk ID: C9C5A968-4AEA-48C7-B90A-DEC986F80DA5 The sample demonstrates two techniques for building the response. For client exceptions, a friendly HTML response is sent in the body as well as the status code and description. Personally I prefer not to do that – it doesn’t make sense to get a 400 error and find text/html when you’re expecting application/json, but it’s easy to do if that’s the functionality you want. The other option is to send an empty response, which the sample does with server exceptions. The obvious extension is to have multiple exceptions representing all the status codes you want to provide, then your code is as simple as throwing the relevant exception – UnauthorizedException, ForbiddenExeption, NotImplementedException etc – anywhere in the stack, and it will be handled nicely.

Read the article
Convert uploaded video files to mp4 using PHP [closed]

- by Subin

I created a PHP video uploading script. I need to convert these files to mp4 for HTML5 VIDEO PLAYER using PHP while uploading . How can I do that ? Here is the PHP code. <?php if(isset($_POST['submit'])){ $user=$_COOKIE['VisitorName']; include('config.php'); session_start(); $session_id='1'; //$session id $path = "/home/simsu/subins/videos/data/videos/"; $valid_formats = array("wmv", "ogv", "mp4", "3gp", "ogg"); if(isset($_POST) and $_SERVER['REQUEST_METHOD'] == "POST") { $name = $_FILES['uploadedfile']['name']; $size = $_FILES['uploadedfile']['size']; if(strlen($name)) { list($txt, $ext) = explode(".", $name); if(in_array($ext,$valid_formats)) { if($size<(100024*100024)) { $actual_image_name = $path.time().".mp4"; $tmp = $_FILES['uploadedfile']['tmp_name']; $upurl="http://vtube.subins.com/files/video?vid=".time(); $title=$_POST['vn']; mysql_query("INSERT INTO videos(title,user,url,vid,ext) VALUES ('$title', '$user','$upurl',NOW(),'$ext')"); echo '<br><h1>'.$_FILES['uploadedfile']['name'] . " uploaded.</h1>"; } else echo "<br><h1>Video file size max 100 MB"; } else echo "<br><h1>Invalid file format.."; } else echo "<br><h1>Please select a video..!"; exit; } } ?>

Read the article
Microsoft releases Visual Studio 2010 SP1

- by brian_ritchie

Microsoft has been beta testing SP1 since December of last year. Today, it was released to MSDN subscribers and will be available for public download on March 10, 2011.The service pack includes a slew of fixes, and a number of new features: Silverlight 4 supportBasic Unit Testing support for the .NET Framework 3.5Performance Wizard for SilverlightIntelliTrace for 64-bit and SharePointIIS Express supportSQL CE 4 supportRazor supportHTML5 and CSS3 support (IntelliSense and validation)WCF RIA Services V1 SP1 includedVisual Basic Runtime embeddingALM Improvements Of all the improvements, IIS Express probably has the largest impact on web developer productivity. According to Scott Gu, it provides the following:It’s lightweight and easy to install (less than 10Mb download and a super quick install)It does not require an administrator account to run/debug applications from Visual Studio It enables a full web-server feature set – including SSL, URL Rewrite, Media Support, and all other IIS 7.x modules It supports and enables the same extensibility model and web.config file settings that IIS 7.x support It can be installed side-by-side with the full IIS web server as well as the ASP.NET Development Server (they do not conflict at all) It works on Windows XP and higher operating systems – giving you a full IIS 7.x developer feature-set on all OS platforms IIS Express (like the ASP.NET Development Server) can be quickly launched to run a site from a directory on disk. It does not require any registration/configuration steps. This makes it really easy to launch and run for development scenarios.Good stuff indeed. This will make our lives much easier. Thanks Microsoft...we're feeling the love!

Read the article
I receive the error 'grub-install /dev/sda failed' while attempting to install Ubuntu as the computer's only OS.

- by Liath

I am attempting to install Ubuntu on a box which was previously running Windows 7. I have also experienced the dreaded "Unable to install GRUB" error. I am not attempting to dual boot. I have previously run a Windows boot disk and removed all existing partitions. If I run the Ubuntu 12.04 install CD and click install after the config screens, I get the error Executing 'grub-install /dev/sda' failed. This is a fatal error. (It is the same error as this question: Unable to install GRUB) All the questions I've read while looking for a solution are related to dual boot. I'm not interested in dual boot, I'm after a clean out the box Ubuntu install. How can I achieve this? (For my sanity, please use very simple instructions when responding. I don't claim to have any talent either for linux or as a sysadmin) Additional details copied from comments dated: 2012-05-29 ~15:19Z After booting from the CD, clicking Try Ubuntu, and then sudo fdisk /dev/sda I get fdisk: unable to seek on /dev/sda: Invalid argument sudo fdisk /dev/sdb gives Device contains neither a valid DOS partiion table, nor Sun, SGI or OSF disklabel. Building a new DOS disklabel with disk identifier 0x15228d1d. Changes will remain in memory only until you decide to write them. After that of course, the previous content won't be recoverable. Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite). Command (m for help): I should add the Live CD desktop is graphically bad. I've got missing parts of programs and the terminal occasionally reflects to the bottom of the screen. But I can't imagine this is related.

Read the article
Only one user can connect to Ubuntu samba server

- by StaticMethod

I setup a samba server on 12.04 LTS, and it works great for one user but not the others. I am trying to map a network drive from a windows 7 laptop. I can successfully authenticate with one user, but the other two both get "Access is denied" errors. Here is my smb.conf file. [global] server string = %h server (Samba, Ubuntu) map to guest = Bad User obey pam restrictions = Yes pam password change = Yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%m max log size = 1000 dns proxy = No usershare allow guests = Yes panic action = /usr/share/samba/panic-action %d idmap config * : backend = tdb [printers] comment = All Printers path = /var/spool/samba create mask = 0700 printable = Yes print ok = Yes browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/printers [share] comment = Ubuntu File Server Share path = /srv/share read only = No create mask = 0755 I know that the service is successfully reading from the /etc/passwd file because if I change the Linux password for the user that works, I have to use the new password when I connect. I changed all the users so they are all members of the same groups (all three users are admins anyway). I only ever have one user connected at a time. Here are the permissions on the shared folder /srv$ ls -l drwxrwxrwx 1 nobody nogroup 16 Feb 22 17:05 share Any ideas?

Read the article
M-Audio Delta starts up at wrong sample rate

- by steevc

When the PC starts my M-Audio Delta 66 is using 48000kHz sampling rate when it is set for 44100 in Envy24. This causes audio to play slower than it should. This is in Kubuntu 14.04 on my new PC using an AMD A8 6500 with 8GB. When I first installed it seemed okay, but at some point it went wrong and has been doing this consistently since then. Kernel is 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:31:42 UTC 2014 i686 athlon i686 GNU/Linux steve@slarti:~$ cat /proc/asound/card2/pcm0p/sub0/hw_params access: MMAP_INTERLEAVED format: S32_LE subformat: STD channels: 10 rate: 48000 (48000/1) period_size: 441 buffer_size: 3528 I can get it to switch to 44100 if I disable/enable the Delta in Pulseaudio volume control, but I have to do this every day and the sound still seems distorted. I can't see any issues in any of the config or log files I can find. If I boot the PC with a Mint Live USB it starts at 44100 and sound fine. Originally reported on Youtube is playing at the wrong speed - maybe soundcard related, but I'll close that and have this more relevant question instead.

Read the article
Enterprise Instrumentation: The 'sessionName' parameter of value 'TraceSession' is not valid

- by Michael Freidgeim

We are still using Enterprise Instrumentation(that was created during .Net 1.1 time)In new Server 2008 environment and IIS 7 we have the following errors:The 'sessionName' parameter of value 'TraceSession' is not valid. A trace session of this name does not exist in the TraceSessions configuration file for Windows Trace Session Manager service. Ensure that a session of this name exists in the TraceSessions configuration file and that the Windows Trace Session Manager service is started. at Microsoft.EnterpriseInstrumentation.EventSinks.TraceEventSink..ctor(IDictionary parameters, EventSource eventSource) --- End of inner exception stack trace --- at System.RuntimeMethodHandle._InvokeConstructor(IRuntimeMethodInfo method, Object[] args, SignatureStruct& signature, RuntimeType declaringType) at System.Reflection.RuntimeConstructorInfo.Invoke(BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture) at System.RuntimeType.CreateInstanceImpl(BindingFlags bindingAttr, Binder binder, Object[] args, CultureInfo culture, Object[] activationAttributes) at Microsoft.EnterpriseInstrumentation.EventSinks.EventSink.CreateNewEventSinks(DataRow[] eventSinkRows, EventSource eventSource)I’ve seen the same errors on development Win7 machines when using IIS. It seems not a problem on Cassini.I've checked ,that Windows Trace Session Manager Service has started and The file C:\Program Files (x86)\Microsoft Enterprise Instrumentation\Bin\Trace Service\TraceSessions.config has corresponding entry<?xml version="1.0" encoding="utf-8" ?><configuration > <defaultParameters minBuffers="4" maxFileSize="10" maxBuffers="25" bufferSize="20" logFileMode="sequential" flushTimer="3" /> <sessionList> <session name="TraceSession" enabled="false" fileName="C:\Program Files (x86)\Microsoft Enterprise Instrumentation\Bin\Trace Service\Logs\TraceLog.log" /> </sessionList></configuration>The errors still continue, but I was able to disable the parameter in eventSink configuration <eventSink name=" traceSink" description=" Outputs events to the Windows Event Trace." type ="Microsoft.EnterpriseInstrumentation.EventSinks.TraceEventSink ">  </ eventSink>Related old post http://bytes.com/topic/net/answers/104761-enterprise-instrumentation-windows-trace-session-managerOne day I wish to replace all EnterpriseInstrumentation calls with NLog.

Read the article
WCF - Automatically create ServiceHost for multiple services

- by Rajesh Pillai

WCF - Automatically create ServiceHost for multiple services Welcome back readers! This blog post is about a small tip that may make working with WCF servicehost a bit easier, if you have lots of services and you need to quickly host them for testing. Recently I was encountered a situation where we were faced to create multiple service host quickly for testing. Here is the code snippet which is pretty self explanatory. You can put this code in your service host which in this case is a console application. class Program { static void Main(string[] args) { // Stores all hosts List<ServiceHost> hosts = new List<ServiceHost>(); try { // Get the services element from the serviceModel element in the config file var section = ConfigurationManager.GetSection("system.serviceModel/services") as ServicesSection; if (section != null) { foreach (ServiceElement element in section.Services) { // NOTE : If the assembly is in another namespace, provide a fully qualified name here in the form // <typename, namespace> // For e.g. Business.Services.CustomerService, Business.Services var serviceType = Type.GetType(element.Name); // Get the typeName var host = new ServiceHost(serviceType); hosts.Add(host); // Add to the host collection host.Open(); // Open the host } } Console.ReadLine(); } catch (Exception e) { Console.WriteLine(e.Message); Console.ReadLine(); } finally { foreach (ServiceHost host in hosts) { if (host.State == CommunicationState.Opened) { host.Close(); } else { host.Abort(); } } } } } I hope you find this useful. You can make this as a windows service if required.

Read the article
Unity in 12.10 comes up behind other windows

- by ams

I've just upgraded from 12.04 to 12.10. For the most part, everything works fine, but I have a few small problems with Unity, or maybe Compiz. When I hit the Super key, or click on the dash launcher, the dash sometimes comes up behind the other windows on the screen. As you can imagine, this makes it somewhat tricky to use. Once it has started coming up behind, no amount of trying again will convince it to come back to the front. Possibly related, the Alt-Tab switcher doesn't show either. It maybe that there isn't one, or maybe that's behind also? Alt-Tab does switch the windows, but there's no visual indicator. When I hit Super-W, the windows do all do the zoom thing, but it's slow and juddery where it used to be smooth in 12.04. I'm using the standard "radeon" driver, same as before, with a triple-head monitor setup (and that works fine). I've not tried the proprietary drivers as I've previously found the multi-monitor support much weaker than the default driver, but maybe that's the way to go now? Video play fine. Even WebGL seems ok. Do other see this problem? Is it a bug? Or have I just got some left-over config from 12.04 in the way?

Read the article
How to schedule time-of-day upgrades

- by Richard

Hello, I'm responsible for about 30 Ubuntu computers at a private K-8 school. We have only a 3Mbps internet connection serving the entire campus, and I would like to ensure that updates are done in the middle of the night - so that daytime tasks are not slowed down. I'm using Ubuntu 10.04, and have set all computers to download and install security updates via the update manager. I have also installed cron-apt, and modified the config file to stagger the start times of the upgrades from about 10pm to 4am local time. HOWEVER - this morning I arrived at the school at 7:30am and all the computers were busy downloading a large security based update. Needless to say, all internet activity was slowed to a crawl (for the next 2 hours), and the computer users were very very upset. This was the event I'm trying so hard to prevent. It seems that my scheme to ensure middle of the night downloads failed, and I'm not sure why. I've also tried some schemes using unattended-upgrades & crontab, but there always seemed to be something scheduling upgrades to occur in addition to the ones I try to force at middle of the night. Is there a sure fire way to absolutely positively guarantee that updates will occur only at one specific time? It would be nice if the update manager just had a drop down menu to specify a designated time. Thanks in advance for any help you can give me.

Read the article
One monitor getting spilled over into other monitor: how to do a 100% reset of gnome graphics configuration

- by Paul Nathan

I had to kill a VMWare process and afterwards, my monitor's configuration is buggy. I have 2 monitors in a side-by-side configuration. My right-hand monitor is the secondary monitor. Upon its right-hand side there are about 50 pixels showing from the left side of the lefthand monitor (ie, as if it was wrapped around). Further, my mouse clicks are registering as about 50 pixels sideways from where they should be. It's as if those 50 pixels between monitors got gobbled. What have I done? I've reset the screen configuration in multiple ways, using xrandr, multiple monitors app, etc. This persists in different side-by-side configurations, and also persists with another user. It does not occur with XFCE. Resetting the Window manager with the Compiz reset WM app does not fix this. I've concluded the burn-to-the-ground approach is likely the best, and would like to do a 100% reset of my graphics settings. It's an Intel integrated chipset. Removing ~/.config/monitors.xml did not work. Also, interestingly, the mouse can mouse-over the 50 errant pixels on the rhs of the right-hand monitor. I hypothesize that it's a compositing problem occurring at the layer where the background, selection, and clicks are caught. Also, inverting the right-hand monitor removes the issue, but renders the screen unusable. Even more datapoints: This happens in KDE as well Sometimes logging into Gnome and running xrandr --output DVI1 --auto resets it, but the issue immediately reappears when I press alt-tab. With Compiz Application Switch turned on, the workspace is 'pushed back' a bit, and the slice on the RHS follows it as well. I'm wondering if it's a flaw in the compiz workspace compositing configuration. I suspect the error was in the compositing configuration. I installed 11.10.

Read the article
Login takes very long, annoying repaints once a minute when logged in: How to troubleshoot?

- by user946850

I am suffering from a strange problem with my Gnome Shell in Ubuntu 12.10. The login takes very long ( 30 sec), with a blank screen. In Google Chrome and Thunderbird (and perhaps in other applications), the main window freezes and is repainted in periodic intervals of less than one minute. The freeze takes several seconds, and it seems that font and appearance of, e.g., tabs and buttons briefly changes. Attempting to enable the second monitor show an error message related to XRANDR. Everything seems to have started three days ago, after I had to force-shutdown the machine while it was hibernating due to low power. (It was hibernating for quite a while and didn't want to stop.) Silly me. I have tried the following measures, with no avail: Checked all package file md5 hashes using debsums Reinstalled all packages using a variant of dpkg --get-selection \* | xargs apt-get install -reinstall Temporarily moved configuration directories such as .gconf, .config and .gnome2 to another location Created a new user account When I choose "Ubuntu" during login, the problems disappear. I am sort of frustrated that reinstalling all packages didn't fix the issue. How to troubleshoot this Gnome Shell (?) problem, short of reinstalling the system? (Or did anyone see this kind of behavior on their machine?)

Read the article
How can I play 24Bit 96000Hz vinyl rips?

- by Peter

I am getting music through the Nvidia HDMI but it is all down-sampled to 44000Hz. I have spent at least 3 hours searching for an answer yesterday. I use Pulse Volume and I even changed the default settings in the Pulse folder to 96000 but it does not work. Though 5.1 sound works perfectly. They all work well in Windows 7, but I prefer to use Ubuntu. All the config files for all the programs are in the etc folder, then look in the pulse folder, and there are 3 three files, 2 of these I changed the permissions and I changed 16 and 44000 to 24 and 96000 as I had read in another forum, but it worked for them and not for me. Though 5.1 works as I have special mp4 file that can check each channel. I did alot of restarts and checking after these changes as nothing had happened, my amp tells me the freq of the signal, which does work which I have tested on Windows 7. I have also gone to systems to download the latest driver for mu Nvidia card. But even if it does not work, I guess I can always play Cd's. But I think my player have become more unstable since I changed the configs, so I may uninstall and install Pulse Volume Control again.

Read the article
custom domain point to tumblr blog

- by Julius

My domain mydomain.com is registered with godaddy. I wish to host my tumblr blog on this domain with nearlyfreespeech.net hosting. My active nameservers at godaddy already point to my authoritative ones at NFS.net which is working. However i'm baffled of the correct configuration to set to point to my Tumblr. Preferably id like (A) my domain http://mydomain.com to host the blog and have http://www.mydomain.com redirect also to http://mydomain.com If this is too difficult my next preference is (B) to have http://www.mydomain.com host the blog whilst http://mydomain.com redirects to http://www.mydomain.com My 3rd preference is to have (C) a sub-domain like http://tumblr.mydomain.com or http://tumblr.mydomain.com to host the blog and i guess have http://mydomain.com and http://www.mydomain.com both redirect to it. I've tried having two aliases mydomain.com and www.mydomain.com pointing to my permanent NFS ip at mydomain.nfshost.com and when i try to add: (1) an A record pointing mydomain.com to the ip 66.6.44.4 as per Tumblr's instructions it tells me i already have the bare domain as an alias so i cant do that. (2) the A record on the www.mydomain.com alias. I can do this with either www.mydomain.com set as an alias or not. But when i tried this with mydomain.com set as the canonical name the result when visiting either mydomain.com or www.mydomain.com was them both continually redirecting to eachother until an error was thrown. So i was wondering if there is a ninja that could save me some hairpulling and tell me the correct way to config A, or else B, or else C.

Read the article
Laptop power button not working

- by DyP

I have a (seemingly rather exotic) Dell Latitude XT2 notebook running Lubuntu 12.04, fresh install. Tried to get the power button to work as expected (opening lubuntu-logout, just as I think it was meant to be out-of-the box), but no success: power button does nothing but forced power-off on long press. Here some more information, please ask if something more could help: Power button is recognized as a device: xinput lists Power Button as a slave keyboard at /dev/input/event1, and I can run a tool to listen to that device and invoke some action (successfully). But using .config/openbox/lubuntu-rc.xml to assign some action to XF86ShutDown or XF86PowerOff does nothing. Works well for any key of the keyboard. xinput --test reports a keycode (key press, key release) of 124 when pressing & releasing the power button. xmodmap -pk lists 124 mapped to XF86PowerOff which seems correct to me (btw: is this the same as XF86ShutDown?) When assigning another keysymname to the 124 keycode, e.g. 'w', still nothing happens when pressing the power button (no window seems to receive a 'w'). Works well for any key on the keyboard. The outputs of xev for a press/release of the power button irritate me: MappingNotify event, serial 41, synthetic NO, window 0x0, request MappingKeyboard, first_keycode 8, count 248 FocusOut event, serial 41, synthetic NO, window 0x2a00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 41, synthetic NO, window 0x2a00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 41, synthetic NO, window 0x0, keys: 93 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 (instead of 93, I also get different values) I might have missed something very basic since I'm not very familiar with both openbox/lubuntu and the X input system. Btw.: same goes for three other special buttons on my laptop..

Read the article
"The protocol 'net.msmq' is not supported."

- by Randolpho St. John

OMG, a new lesson! Will wonders never cease? So I ran into an interesting issue setting up a WCF service to consume an MSMQ queue. I won't bother you with the details of how to actually build a WCF/MSMQ service; there are plenty of tutorials on the subject. I want to share with you an interesting error that I ran into and the surprisingly simple fix. The error occurs when attempting to generate a Service Reference or even simply browsing to the WSDL of your WCF/MSMQ service in the form of a YSOD with the following error: "The protocol 'net.msmq' is not supported." After a lot of Googling on the subject turning up plenty of questions with the same error but no answers. So I went digging into some application level config files on a server that already had a WCF/MSMQ service successfully set up by the network admin, and the answer was amazingly simple: If you are hosting an MSMQ/WCF service in IIS, you have to tell IIS to allow net.msmq protocol. It's in the advanced settings for the application or site in which you are hosting the service. .... aaaand, that's it.

Read the article
Run Grunt task in Visual Studio Release Build with a bat file

- by Aligned

Originally posted on: http://geekswithblogs.net/Aligned/archive/2014/08/19/run-grunt-task-in-visual-studio-release-build-with-a.aspx 1. Add a BeforeBuild in your csproj file. Edit the xml with a text editor. <Target Name="BeforeBuild"> <Exec Condition="'$(Configuration)' == 'Release'" Command="script-optimize.bat" /> </Target> 2. Create the script-optimize.batREM "%~dp0" maps to the directory where this file exists cd %~dp0\..\YourProjectFolder call npm uninstall grunt call npm uninstall grunt call npm install --cache-min 604800 -g grunt-cli call npm install --cache-min 604800 grunt typescript requirejs copy less:compile less:mincompileThis grunt command will compile typescript, run the requireJs optimizer, complie and minimize less.3. Make it use the minified code when the Web.config compilation debug is set to false  <Target Name="CustomCollectFiles"> <ItemGroup> <_CustomFiles Include="Scripts-Release\**\*" /> </ItemGroup> </Target> That should be all you need to get a Grunt task to minify and combine JS (plus other tasks) in Visual Studio Release build with debug = false. This is a great video of Steve Sanderson talking about SPAs, npm, Knockout, Grunt, Gulp, ect. I highly recommend it.

Read the article
Single CAS web application in a cluster

- by Dolf Dijkstra

Recently a customer wanted to set up a cluster of CAS nodes to be used together with WebCenter Sites. In the process of setting this up they realized that they needed to create a web application per managed server. They did not want to have this management burden but would like to have one web application deployed to multiple nodes. The reason that there is a need for a unique application per node is that the web-application contains information that needs to be unique per node, the postfix for the ticket id. My customer would like to externalize the node specific configuration to either a specific classpath per managed server or to system properties set at startup.It turns out that the postfix for ticket ids is managed through a property host.name and that this property can be externalized.The host.name property is used in: /webapps/cas/WEB-INF/spring-configuration/uniqueIdGenerators.xmlIt is set in /webapps/cas/WEB-INF/spring-configuration/propertyFileConfigurer.xmlin a PropertyPlaceholderConfigurer.The documentation for PropertyPlaceholderConfigurer:http://static.springsource.org/spring/docs/2.0.x/api/org/springframework/beans/factory/config/PropertyPlaceholderConfigurer.htmlThis indicates that the properties defined through the PropertyPlaceHolderConfigurer can be externalized.To enable this externalization you would need to change host.properties so it is generic for all the managed servers and thus can be reused for all the managed servers: host.name=${cluster.node.id}Next step is to change the startup scripts for the managed servers and add a system property for -Dcluster.node.id=<something unique and stable>.Viola, the postfix is externalized and the web application can be shared amongst the cluster nodes.

Read the article

< Previous Page | 266 267 268 269 270 271 272 273 274 275 276 277 | Next Page >