Search Results

Search found 8233 results on 330 pages for 'unresolved external'.

Page 271/330 | < Previous Page | 267 268 269 270 271 272 273 274 275 276 277 278  | Next Page >

• Cisco 3560+ipservices -- IGMP snooping issue with TTL=1

  - by Jander

  I've got a C3560 with Enhanced (IPSERVICES) image, routing multicast between its VLANs with no external multicast router. It's serving a test environment where developers may generate multicast traffic on arbitrary addresses. Everything is working fine except when someone sends out multicast traffic with TTL=1, in which case the multicast packet suppression fails and the traffic is broadcast to all members of the VLAN. It looks to me like because the TTL is 1, the multicast routing subsystem doesn't see the packets, so it doesn't create a mroute table entry. If I send out packets with TTL=2 briefly, then switch to TTL=1 packets, they are filtered correctly until the mroute entry expires. My question: is there some trick to getting the switch to filter the TTL=1 packets, or am I out of luck? Below are the relevant parts of the config, with a representative VLAN interface. I can provide more info as needed. #show run ... ip routing ip multicast-routing distributed no ip igmp snooping report-suppression ! interface Vlan44 ip address 172.23.44.1 255.255.255.0 no ip proxy-arp ip pim passive ... #show ip igmp snooping vlan 44 Global IGMP Snooping configuration: ------------------------------------------- IGMP snooping : Enabled IGMPv3 snooping (minimal) : Enabled Report suppression : Disabled TCN solicit query : Disabled TCN flood query count : 2 Robustness variable : 2 Last member query count : 2 Last member query interval : 1000 Vlan 44: -------- IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Robustness variable : 2 Last member query count : 2 Last member query interval : 1000

  Read the article

• Port knocking via SSH tunnels

  - by j0ker

  I have a server running in my university's internal network. There is only one SSH daemon running which is secured by port knocking with knockd. Works fine if I try to connect from within the internal network. But since the server has no external IP, I have to tunnel into the internal network every time I want to access the server from outside. And since tunneling only works for a single port I cannot do the port knocking as easily as from an internal client. In fact, I don't get it to work at all. What I'm trying is opening tunnels for all the different ports that have to be knocked. Then I send TCP-SYN packets into the tunnels. But that doesn't work even for a single port. If I establish the tunnel on the first port in the knock sequence and send a packet through it, it doesn't reach the server. There is no entry in the log file of knockd, while there should be something like 123.45.67.89: openSSH: Stage 1 (as shown with internal knocks). So I guess, the problem doesn't exist within my knocking script but is a more general one. Are there any known problems with what I'm trying to do? Is it even possible or am I missing something? Thanks in advance!

  Read the article

• Time Drift on VM servers, need a reliable solution

  - by zeroasterisk

  We have some windows server 2008 VMware instances on multiple physical servers (hosted) and an application which requires the time to be synced across the server instances. Obviously, VMware has problems with this and we really have never gotten it working any better, we have setup the servers to poll for an NTP update every minute which mitigates the problem (in a fairly crude way). Except that every once in a while, the update will fail (because there's already too much drift) and then windows never does an NTP update afterwards which eventually allows the servers to drift far enough apart that our application breaks, and we notice. We are thinking about changing hosts to Xen servers on approximately the same setup, and I anticipate similar problems. can anyone tell me if Xen has the same time-drift issues VMware does, for guests? can anyone tell me what the best windows server settings are for syncing with an external NTP server to keep things in sync: how frequently do you recommend syncing? (assuming every minute) do you recommend running our own NTP server - even if it has to be on a virtual instance? (assuming not) is there any way to tell windows to sync with the NTP server no matter what the time difference is? any other suggestions for keeping windows servers time in sync? I have become familiar with [ http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1318 ] and it's helped, but it's not been totally effective (see above). thanks much!

  Read the article

• replacing buffalo lonkstations with FreeNAS, overall backup strategy, am I on the right path?

  - by Shreko

  We've been using 2 Buffalo LinkStations of 320Gb each for shared directory and employee's server storage (around 20 employees). So only documents (word, excel, cad drawings etc.) and database backup of the main application server (ERP, Accounting) 1 buffalo box serves as a main one, located at the server room, next to the main application server and the other buffalo box is located on the opposite side of the building (for fire protection) in a secure storage room and backs up the first one. We also have several external HDs that backs up everything from the buffalo box for an offsite backup. After 3.5 years of using these, capacity is a main limitation, I'm planning a replacement and would like to use FreeNAS (we already use monowall with great success). I would like to keep it simple and continue similar setup, building two low power boxes with 1 hd (2Tb) each. Is low power atom mobo OK? Not sure about HDs? I've read on this site somebody mentioning more seagate ES2 as more reliable and better performing. How would those eco/green drives compare. We've been pretty happy with speed of Buffalo boxes and I don't want my users to notice any slowdown. Any suggestion?

  Read the article

• SFTP, ChrootDirectory and multiple users

  - by mdo

  I need a setup where I can put the contents of several user folders to a DMZ server from where external clients can download it, protocol SFTP, Linux, OpenSSH. To ease administration we want to use one single user for the upload. What does work is to define ChrootDirectory /home/sftp/ in sshd_config, set the according ownership and modes and define a home dir in passwd so that the working directory of the user fits. This is my structure: /home/sftp/uploader/user1/file1.txt /user2/file2.txt The uploader user can write file1.txt and file2.txt to the corresponding folders and by having the user folders (user1, user2) set to the users' primary group + setting SETGUID on the folders the users are able to even delete the files (which is necessary). Only problem: because /home/sftp/ is the chroot base dir the users can change updir and see other users' folders, though not being able to change into because of access rights. Requirement: We want to prevent users to change to /home/sftp/uploader/ and see other users' folders. My requirements are to use SFTP, have one upload user and every user must have write access to his home dir. Obviously it's not an option to use something like ChrootDirectory %h because every path component of the chroot path needs to have limited access rights, so as far as I understand this does not work.

  Read the article

• unable to copy file to folder, permission denied without explanation

  - by ValekHalfHeart

  Recently Norton Internet security deleted ml.exe (an assembler I use to program in masm32) off of my computer, thinking that one of the programs I had written with it was a virus (it was most certainly not). Fortunately, I had a copy of ml.exe backed up in an external hard drive, and tried to copy it over to my computer. The old ml.exe was located in C:\masm32\bin, so I tried to copy the new one to that location. After disabling Norton (which had opened the folder and preventing me from accessing it), I am still unable to copy the new file to C:\masm32\bin. When I tried, Windows announced that I would need Administrator permission to copy the file. Since I'm an admin, I figured this wouldn't be a problem although it was unexpected, as I have never had to provide administrator permission to access this folder before. However, instead of prompting me to enter my password, Windows simply refuses to copy the file: I repeat, I was not asked to provide a password. It simply says that I do not have permission. Does anyone know what's happening and how to fix it? Is Norton still causing problems, or it something else?

  Read the article

• Route all wlan0 traffic over tun0

  - by Tuinslak

  I'm looking for a way to route all wlan0 traffic (tcp and udp) over tun0 (openvpn). However, all other traffic originating from the device itself should not be routed through tun0. I'm guessing this could be realized using iptables or route, but none of my options seem to work. # route add -net 0.0.0.0 gw 172.27.0.1 dev wlan0 SIOCADDRT: No such process Info: This is because the VPN server is not redundant, and wlan users are not really important. However, all services running on the device are fairly important and having a VPN virtual machine with no SLA on it is just a bad idea. Trying to minimize the odds of something going wrong. So setting the VPN server as default gateway is not really an option. I also want all wlan0 user to use the VPN server's IP address as external IP. Edit with the script provided: root@ft-genesi-xxx ~ # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.27.0.17 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.13.37.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 172.27.0.0 172.27.0.17 255.255.192.0 UG 0 0 0 tun0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 root@ft-genesi-xxx ~ # ./test.sh RTNETLINK answers: No such process root@ft-genesi-xxx ~ # cat test.sh #!/bin/sh IP=/sbin/ip # replace with the range of your wlan network, or use fwmark instead ${IP} rule add from 10.13.37.0/24 table from-wlan ${IP} route add default dev tun0 via 127.72.0.1 table from-wlan ${IP} route add 10.13.37.0/24 dev wlan0 table from-wlan

  Read the article

• postfix not sending domain mail to mx

  - by orlandoresorts

  I'm trying to get postfix to forward email to my domain which is hosted by gmail. As I don't have any users on my server nor do I want to. Here's how I have things set up.. LEt's say you and I have a domain called mcdonalds.com the registrar has mcdonalds.com MX records pointing to gmail. (everything works for like a year) Now we set up a server to host a website. Then we create a mail account called [email protected] and send mail locally from the server using roundcube. This works. We can send mail to cnn.com we can send mail to serverfault.com we can email any/everyone. BUT we cannot send mail to our own domain mcdonalds.com So I cannot email [email protected] I cannot email [email protected] I cannot email [email protected] It gives the error: SMTP Error (450): Failed to add recipient "[email protected]" (4.1.1 : Recipient address rejected: User unknown in virtual mailbox table). I'm guessing because it is looking at the local server to find the mailbox and it doesn't exist. So how to I tell the server for any mail going to mcdonalds.com for [email protected] to send to my external mail server and NOT to lookup on the local www box we set up with zpanel. Any ideas?

  Read the article

• Nginx rewrite for link shortener + Wordpress pretty URLs

  - by detusueno

  Okay so I installed Nginx/PHP/MySQL/Wordpress via a online walk through, and it had me enter these rewrites to enable Wordpress pretty URLs: if (-f $request_filename) { break; } if (-d $request_filename) { break; } rewrite ^(.+)$ /index.php?q=$1 last; error_page 404 = //index.php?q=$uri; This is then included in the vhost for my domain. What I'm trying to do now is add some redirection/link shortner rewrites that will play nice with the setup I have in mind. I'd like to redirect "x.com/y" to "x.com/script.php?id=y" for all external links that I post. The Wordpress link setup right now has almost all internal links begin with "news" (x.com/news/post-blah, x.com/news/category/1, etc) BUT I also have a few root links that point to some internal content (x.com/news, x.com/start). I'm guessing that's going to cause some conflicts. What's the best approach to do this? I've never worked with Nginx (or any rewrite rules) but maybe I can distinguish between "x.com/news" and "x.com/news/" to allow it to play nice? I had a friend setup a working version of this in Apache and it'd be nice if I could get this up on Nginx again.

  Read the article

• Intermittent 5.7.1 email bounce to Exchange 2007

  - by Steve Kennaird

  My knowledge of Exchange isn't particularly great, so excuse me if some of the terminology I use isn't quite right. I'm primarily a web developer who's now responsible for a small business's network. We have a server running SBS 2008 and Exchange 2007. Generally, everything works well, emails are able to be sent to both internal and external domains without issue. We've only got ~20 users, Exchange is sitting on a single server. I use SendGrid to send emails generated by our externally hosted website to users in the office. Primarily, order notifications are sent to [email protected]. Without any pattern and less than once per week on average, an email to [email protected] will bounce back, and the logs on SendGrid detail the following error: 550 5.7.1 Unable to relay for [email protected] Either side of that failed delivery attempt, I'm able to send and receive emails to/from [email protected]. Having done some research, incorrect reverse DNS seems like it could be a cause of intermittent bounces like this. Having used nslookup, I have found that the reverse DNS doesn't map like it should, e.g. Office IP: 135.325.351.123 (made up IP, for example only) Domain: office.somedomain.com (made up, for example only) Reverse DNS: somedomain.gotadsl.co.uk (half made up) Could this be a cause? I'm sure that the IP address and the domain should map to each other. Also, it has been suggested to me that as the Exchange server is on a network with an ADSL connection, that could be a potential cause as the connection "goes up and down all day long". I don't have an opinion on this, as I don't have enough knowledge of Exchange/ADSL to form a reliable opinion. Can anyone offer any insight as to whether one or both are actually potential causes, or if there is another possible cause?

  Read the article

• Using URL rewrite module for http to https redirect

  - by johnnyb10

  Following ruslany's suggestion on the URL Rewrite Tips page here, I'm trying to use URL Rewrite to redirect http:// requests for my site to https://. I've written and tested the rule using a test site I set up, and so now the final piece is to create a second site (http) to redirect to my https site. (I need to use a second site because I don't want to uncheck the "Require SSL encryption" checkbox on my existing site.) I'm an IIS newbie so my question is: how do I do this? Should I create a site with the same name and host header, only it will be bound to http? Will IIS let me create a site with the same name? I don't want to screw anything up with my existing site (which is a SharePoint site, currently used by external users). That site currently has http and https bound to it. So my assumption is that, using ISS (not SharePoint), I will create a new site (http only) with the same name and host header as my existing site, and add the URL Rewrite rule to the http site. And then I guess I should remove the http binding from my existing site? Does that seem correct? Any advice, gotchas, etc., would be appreciated. Thanks.

  Read the article

• Transfering Files to server IP and port

  - by Mason

  I need to transfer files from my local computer on windows 7 to a server running linux. I access the server with putty through ssh at a specific IPv4 address and port number. I've attempted using the pscp command from my local computer but was denied access by the server. "Fatal: Network error: Connection refused" c:>pscp test.csv userid@**IPv4_Addres***:Port# /path/destination_file_name. Either the server blocks all pscp attempts from unauthorized users (most likely my laptop included) or I used the command incorrectly. If you have experience using this command, where exactly will the file get transfered to, I'm assuming that the path destination starts at my home directory in the server. Also if you have any other alternative methods of transfering the files let me know. Update 1 I have also tried using WinSCP however I got permission denied for that as well, it looks like the server will not let me upload or save files. Solved I had a complete lapse of memory and forgot about sudo (spent too much time with scripts the last 2 months), so I was able to change the permissions to allow external editing. Thanks for all the help guys!

  Read the article

• Using URL rewrite module for http to https redirect

  - by johnnyb10

  Following ruslany's suggestion on the URL Rewrite Tips page here, I'm trying to use URL Rewrite to redirect http:// requests for my site to https://. I've written and tested the rule using a test site I set up, and so now the final piece is to create a second site (http) to redirect to my https site. (I need to use a second site because I don't want to uncheck the "Require SSL encryption" checkbox on my existing site.) I'm an IIS newbie so my question is: how do I do this? Should I create a site with the same name and host header, only it will be bound to http? Will IIS let me create a site with the same name? I don't want to screw anything up with my existing site (which is a SharePoint site, currently used by external users). That site currently has http and https bound to it. So my assumption is that, using ISS (not SharePoint), I will create a new site (http only) with the same name and host header as my existing site, and add the URL Rewrite rule to the http site. And then I guess I should remove the http binding from my existing site? Does that seem correct? Any advice, gotchas, etc., would be appreciated. Thanks.

  Read the article

• How to make a bootable USB drive out of a bootable DVD or CD

  - by Svish

  Is there a "universal" way of how you can make a bootable USB drive out of a bootable dvd or cd? What makes a USB drive bootable? What makes a dvd and cd bootable? For example there is a program called UNetBootin which can make bootable USB drives, but seems like it only works with various linux distributions. (Tried it with a Win7 image and the SystemRescueCD, which didn't work so well...). Main reason I ask is that I have a Support DVD which came with an Asus EEE, and it of course doesn't have an external dvd drive. So I am curious if I can sort of move that dvd over to a USB drive so that I can use it without buying one. Not asking just specifically about this one case though, I am curious to know a bit more about this in general. So, if you have a general bootable DVD or CD (Or a DVD or CD image for that matter), could be linux distro, windows install disk, support disks, etc., is it possible to "move" it over to a USB drive and make that work like the DVD or CD did? (Being bootable and all).

  Read the article

• SVG doesn't work on subdomain - some browsers try to download rather than display

  - by John Catterfeld

  I have a site with a 'development' subdomain, which displays my SVG file exactly as intended. However when I copy it across to www, or any other subdomain (e.g. 'test') some browsers try to open the file in an external editor, therefore asking me to download the file rather than displaying it. For example: http://development.mysite.com/test.svg - works http://www.mysite.com/test.svg - doesn't work The SVG file: <?xml version="1.0" standalone="no"?> <!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd"> <svg xmlns="http://www.w3.org/2000/svg" version="1.1"> <circle cx="100" cy="50" r="40" stroke="black" stroke-width="2" fill="red" /> </svg> This happens in Firefox, Chrome and Safari, however IE9 and above display the file as intended. It is a Windows hosting, and I have <mimeMap fileExtension=".svg" mimeType="image/svg+xml" /> in my web.config file My hunch is that there must be some setting on the server which I need my hosting company to make. Can anyone suggest what might cause this issue?

  Read the article

• virtual machines, dual booting and data disks on SSD

  - by stevemarvell

  This is in planning, so if I've got the strategy wrong, please let me know. There are multiple questions here, but I think they all degenerate to the same answers. The hardware is a laptop with a single SSD. I'm trying to not lose the performance of the SSD. I plan a native dual booting Windows (plus cygwin) and Linux machine which is my BYOD and represents the development environment. I keep the codebase on a shared partition (though sometimes this is an external thunderbolt SSD) which can be natively "mounted" by whichever OS is in operation. I boot into one or the other environments depending on the task in hand. Sometime I have to develop with windows tools, but generally, Linux is my preferred development environment. It would be ideal if I could VM the other OS and run either in either. I'm going to assume, because I've not found a sensible VM based solution, that I have get samba involved to share the code partition between VMs. Is this going to blow my SSD performance in the VM? The client also supplies me with a VM for the target environment, usually linux. This is not often suited to development and is used for testing only. I normally keep two copies of this, one as a sandbox and one which I deploy to using the client's preferred method. I keep these VM snapshots on the shared partition. The latter is interacted with over the network and so has no disk sharing requirements. However, it would be useful for the sandbox to be able to "mount" the code base from the natively running OS. Is this samba or nfs again, depending on the native OS? Am I missing a trick which allows this to all work smoothly with all four environments running at once without loosing the SSD performance?

  Read the article

• Comprehensive solution for managing patches, event viewing, change management, inventory, etc

  - by Holocryptic

  I'm looking for a solution that incorporates most or all of the following: Patch Management, Server event viewing/tracking, AD change management, ticketing and internal/external kb, remote access - ability to shadow user sessions or create new ones, imaging, and inventory. Our environments contains Windows Servers and ESXi Hosts (We're not completely virtual, but we're moving that direction). Various Cisco and Linksys switches and firewalls. This is a tall order, and I don't know if it can be done on a reasonable budget. I've looked and found some questions on SF that deal with some of this: http://serverfault.com/questions/72015/active-directory-management-tools-for-medium-sized-forest-less-than-1000-users http://serverfault.com/questions/4021/are-there-any-tools-to-do-change-management-with-active-directory-group-policy http://serverfault.com/questions/21752/what-is-a-good-patch-update-management-server What I'm ideally looking for is a reasonably cheap solution that integrates the features into a central interface. We're a non-profit, so money is a limiting factor (the cheaper, the better; but we have a max of $15k). What we are trying to avoid is having to deal with multiple vendors, while maintaining scalability (we're creating more sites that we'll have to manage). Is this possible, or will we have to cobble together something to make it work for us?

  Read the article

• What are these CPU cache settings? Snoop Filter, ACL prefetch, HW prefetch

  - by eater

  I was in my BIOS setup turning on VT-x support today and saw these other settings. A little googling indicates that they each seem to turn on some sort of optimization to do with the CPU's L2 cache. They were all turned off by default. The processor in question is an Intel Xeon quad-core 3.4GHz (X5492). My OS is Linux 2.6.35.10-74.fc14.x86_64 #1 SMP Thu Dec 23 16:04:50 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux. I have 4GB of RAM if that matters. Here's what the BIOS manufacturer has to say: Snoop Filter Enabling the snoop filter typically improves performance by reducing snoop traffic on the frontside bus in dual processor configurations. Well I like the sound of improved performance. Why would the BIOS have this off by default? Or by dual processor do they not mean multi-core? Regardless, is there a downside if this is on? ACL Prefetch When enabled, the Adjacent Cache Line Prefetcher fetches both cache lines that comprise a cache line pair when it determines required data is not currently in its cache. When disabled, the processor will only fetch the cache line required by the processor. HW Prefetch Fetches an extra line of data into L2 from external memory. Both of these sound like optimizations that have some drawbacks. What are the reasons to turn them on? What are the reasons to leave them off. Why is the default off?

  Read the article

• Windows 7, going crazy with environment variables

  - by roymustang86

  So, I am trying to learn java. I installed the JDK and proceeded to write a few programs. Each time, I have to give the path to javac.exe to compile the .java file. SO, I decided to tweak the %PATH% variable. And no matter what I change it to, it doesn't work. when I do an echo %PATH%, I get 'Program' is not recognized as an internal or external command, operable program or batch file. This is my Path variable contents : C:\app\product\11.1.0\client_1\bin;%CommonProgramFiles%\Microsoft Shared\Windows Live;%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\;"C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\";"C:\Program Files\Broadcom\Broadcom 802.11";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\12.0\DLLShared\";"C:\Program Files (x86)\Roxio\OEM\AudioCore\";"C:\Program Files (x86)\Intel\Services\IPT\" How do I work around this? the double quotes were not there before, I added it thinking the space was the problem.

  Read the article

• E-mail duplication problem

  - by Gavin Osborn

  I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

  Read the article

• Removing extended partition without deleting logical in it

  - by HisDudeness

  I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

  Read the article

• which grabber is good enough to get 1000fps?

  - by user261002

  I have two framegrabber with a fast camera (1800+ fps). can anybody who understand the hardware, explain to me which of the following grabbers can help me more to grab 1000fps ? here are the the features of the two grabbers : Inspecta-5 Full Camera Link® Version: · Support for line scan and area cameras. · Video data rate of up to 660 Mbytes/sec. · PCI – X bus interface for 64 Bit data width and 66 MHz clock frequency. · PCI bus interface for 32 Bit data width and 33 MHz clock frequency. · 2 Gigabyte Onboard Memory for fast video streams. · Four opt coupled input- output ports for external trigger and encoder signals. · 528 Mbytes/sec. maximum data rate on the PCI–X Bus. · SDK for Windows 2000/XP SILICONSOFTWARE V-Series Camera Link : “microEnable IV VD4-CL” · Camera Pixel Clock Support 85 MHz · Area Scan Cameras 32k * 64k max. image size · Line Scan Cameras 64k max. image width · Acquisition Buffer: 512 MB DDR-RAM · Sustainable Transfer Rate (max.) 850 MBytes/sec. · microEnable SDK for Windows XP/Vista/ 7/ Linux

  Read the article

• Thomson router reboots unexpectedly with an apparent remote connection attempt

  - by ChrisF

  I've got a weird problem. Every so often my rooter (a Thomson TG585 v8 running version 8.2.7.8 of it's firmware) reboots itself. It seems to be associated with this message in the event log: FIREWALL replay check (1 of 2): Protocol: ICMP Src ip: 183.178.144.177 Dst ip: xxx.xxx.xxx.xxx Type: Destination Unreachable Code: Host Unreacheable xxx.xxx.xxx.xxx is my external IP address 183.178.144.177 resolves to 183178144177.ctinets.com We've got a student from Hong Kong staying with us at the moment and the reboots seem coincidental with him starting up his laptop. I say this because a check on ctinets.com shows it to be based in Hong Kong, though our guest's laptop doesn't appear to have any software related to this company installed. I say "apparently" as he is running the Chinese version of Windows and his English doesn't cover technical subjects like this. I know this is an incoming message but I was assuming that it was in response to something on the student's laptop which is why the first thought was malware, but we've got anti virus on all the other machines and have run malwarebytes on his with a negative result so I don't think the problem is due to a virus or (known) trojan. What else can I do to stop this and identify the cause?

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• What USB key would you recommend using for running a Windows 7 VM off of?

  - by Darryl Hein

  Because I can't find a good PHP editor for OSX, I develop in Windows with PhpEd. At the moment, my development time is split between a desktop and a laptop. To partially solve the problem of having 2 different environments, I have installed a virtual machine (through Virtual Box) and put the hard drive file on an external hard drive. At the moment, I've been connecting it through Firewire 800. I have 2 problems with this setup: (1) The hard drive is fairly large so to carry the laptop and hard drive I pretty much require a backpack. (2) The hard drive requires quite a bit of power and therefore reduces the battery life (by about 40%). My thought is to move the VM hard drive onto a USB key. I realize it will be slower, but as I'm just using it for PHP development, there isn't a lot of disk activity in the VM. The only really intense time is boot up, otherwise, it just about sits idle. Do anyone have any suggestions on a USB key to use for the VM? It would need to a minimum of 32GB.

  Read the article

< Previous Page | 267 268 269 270 271 272 273 274 275 276 277 278  | Next Page >