Search Results

Search found 18791 results on 752 pages for 'edit lopez'.

Page 275/752 | < Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >

  • Trying to use HUAWEI E173 on Ubuntu 12.04

    - by Scott Warren
    I have a HUAWEI E173 usb stick to access the internet. It works normally on windows but I need to use it on my Ubuntu system. I plug it in, and after 25-20 seconds the status light turns green and blinks twice every 3 seconds. I see no changes in my system whatsoever, nothing gets installed, I don't get prompted for my PIN. I tried to create a connection using edit connections. I entered the following parameters: Turkey, Turkcell, My Plan is not listed, Internet. Nothing happens. I tried the lsusb command and got the following: tosh2000@tosh:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 058f:a001 Alcor Micro Corp. Bus 001 Device 004: ID 12d1:14ba Huawei Technologies Co., Ltd. I tried the usb-devices command and can see the device: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=14ba Rev=00.00 S: Manufacturer=HUAWEI Technology S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Based on other advice I found, I tried the following command: sudo modprobe usbserial vendor=0x12d1 product=0x14ba Again, nothing happened. My question is why does the "enable mobile broadband" not populate automatically in the dropdown networking menu and how can I can I start using the device? Thank you.

    Read the article

  • apt sources.list disabled on upgrade to 12.04

    - by user101089
    After a do-release-upgrade, I'm now running ubuntu 12.04 LTS, as indicated below > lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise However, I find that all the entries in my /etc/apt/sources.list were commented out except for one. QUESTION: Is it safe for me to edit these, replacing the old 'lucid' with 'precise' in what is shown below? ## unixteam source list # deb http://debian.yorku.ca/ubuntu/ precise main main/debian-installer restricted restricted/debian-installer # disabled on upgrade to precise # deb-src http://debian.yorku.ca/ubuntu/ precise main restricted # disabled on upgrade to precise # deb http://debian.yorku.ca/ubuntu/ lucid-updates main restricted # disabled on upgrade to precise # deb-src http://debian.yorku.ca/ubuntu/ lucid-updates main restricted # disabled on upgrade to precise # deb http://debian.yorku.ca/ubuntu/ precise universe # disabled on upgrade to precise # deb-src http://debian.yorku.ca/ubuntu/ precise universe # disabled on upgrade to precise # deb http://debian.yorku.ca/ubuntu/ precise multiverse # disabled on upgrade to precise # deb-src http://debian.yorku.ca/ubuntu/ precise multiverse # disabled on upgrade to precise # deb http://debian.yorku.ca/ubuntu lucid-security main restricted # disabled on upgrade to precise # deb-src http://debian.yorku.ca/ubuntu lucid-security main restricted # disabled on upgrade to precise # deb http://debian.yorku.ca/ubuntu lucid-security universe # disabled on upgrade to precise # deb-src http://debian.yorku.ca/ubuntu lucid-security universe # disabled on upgrade to precise # deb http://debian.yorku.ca/ubuntu lucid-security multiverse # disabled on upgrade to precise # deb-src http://debian.yorku.ca/ubuntu lucid-security multiverse # disabled on upgrade to precise # R sources # see http://cran.us.r-project.org/bin/linux/ubuntu/ for details # deb http://probability.ca/cran/bin/linux/ubuntu lucid/ # disabled on upgrade to precise deb http://archive.ubuntu.com/ubuntu precise main multiverse universe

    Read the article

  • Cant get php script to connect to asterisk internal mysql database

    - by Bilbo
    Im trying to get a PHP script to connect to Asterisks internal sql database. I tried the to use the standard method for example $con = mysqli_connect("192.168.1.126","root","mysql","asterisk"); However when I log into the asterisk server to access the mysql database all i need it to type "mysql" and im logged in. Im wondering is it possible for my php script to connect to asterisk internal database. //edit The following mysql error is shown Warning: mysqli_connect(): (HY000/2003): Can't connect to MySQL server on '192.168.1.126' (111) in /var/www/html/project/sipSubScript.php on line 6 Failed to connect to MySQL: Can't connect to MySQL server on '192.168.1.126' (111)

    Read the article

  • Help implementing virtual d-pad

    - by Moshe
    Short Version: I am trying to move a player around on a tilemap, keeping it centered on its tile, while smoothly controlling it with SneakyInput virtual Joystick. My movement is jumpy and hard to control. What's a good way to implement this? Long Version: I'm trying to get a tilemap based RPG "layer" working on top of cocos2d-iphone. I'm using SneakyInput as the input right now, but I've run into a bit of a snag. Initially, I followed Steffen Itterheim's book and Ray Wenderlich's tutorial, and I got jumpy movement working. My player now moves from tile to tile, without any animation whatsoever. So, I took it a step further. I changed my player.position to a CCMoveTo action. Combined with CCfollow, my player moves pretty smoothly. Here's the problem, though: Between each CCMoveTo, the movement stops, so there's a bit of a jumpiness introduced between movements. To deal with that, I changed my CCmoveTo into a CCMoveBy, and instead of running it once, I decided to have it CCRepeatForever. My plan was to stop the repeating action whenever the player changed directions or released the d-pad. However, when the movement stops, the player is not necessarily centered along the tiles, as it should be. To correctly position the player, I use a CCMoveTo and get the closest position that would put the player back into the proper position. This reintroduces an earlier problem of jumpiness between actions. What is the correct way to implement a smooth joystick while smoothly animating the player and keeping it on the "grid" of tiles? Edit: It turns out that this was caused by a "Bug Fix" in the cocos2d engine.

    Read the article

  • Squid traffic tunneled through VPN

    - by NerdyNick
    So what I'm trying to do is have a Squid Proxy run on 1 machine along side a VPN connection. What I want to happen is all traffic running though the Squad Proxy would run though the VPN for its outbound. ie Desktop - (Squid Proxy - VPN) The goal is to allow my desktop selective tunneling through the VPN. So that Instant Messaging and the like that do not need to run through the VPN can go through my normal traffic. Typically I would go though a SSH Proxy but currently am forced to use VPN to gain entry into the office, and a Squid proxy seemed like it might work out the easiest for what I am needing. EDIT Realize I forgot to actually state what problem I'm running into. I have the Squid setup and verified it works, but once I connect to the VPN. All requests to Squid get accepted but Squid is unable to make the request over the VPN. So the client ends up just sitting there.

    Read the article

  • How do you deal with translating theory into practice?

    - by Mr. Shickadance
    Hello all! Being a computer scientist in a research field I am often tasked with working alongside professionals outside of the software domain (think math people, electrical engineer etc), and then translating their theories and ideas into real-world implementations. I often find it difficult when they present a theoretical problem which appears to be somewhat disconnected from reality. I am not saying that the theory is bogus, only that it is difficult to translate into real-world situations. For example, recently I have been working with software defined radios. We are exploring many different areas, but often the math specialists in my group would present a problem which is heavily grounded in theory (signal processing, physics, whatever). I often struggle at times where it is hard to draw direct parallels between the theory and the real-world implementation that I need to develop. Say we are working on an energy detector, the theory person in my group would say "you need to measure the noise variance with no signal present." This leads me to think "how the hell do I isolate noise from a signal in reality?" There are many examples, but I hope you see where I am going. So, my question is how does one deal with implementation of theoretical concepts when the theory seems detached from reality? Or at least when the connections are not so clear. Or perhaps, the person with the 'theory' may be ignorant of real restrictions? Note: I found this to be a hard question to ask - hopefully you are following me. If you have suggestions on how I could improve it, by all means let me know! Thanks for looking! EDIT: To be a bit more clear, I understand in situations like this that I must learn that specific domain myself to an extent (i.e. signal processing), but I am more concerned with when those theoretical concepts do not appear to be as grounded in practice as one would like.

    Read the article

  • ubuntu 9.10 screen flickering problem on Thinkpad R31 with Intel 83830 Graphics

    - by PA
    I am trying to revitalize an old Thinkpad R31 that has the Intel 82830 graphics and only 256 MB of RAM. I have tried a Xubuntu 9.10 Live CD. After booting the screen blinks so much that it is practically unreadable. I have searched for updated IBM Thinkpad drivers but I only found drivers for Windows on the Thinkpad support web site. EDIT: I have changed the title and the description. It is not a problem of the drivers. It seems to be a problem with the kernel. See my own answer below.

    Read the article

  • Firefox extension to dinamically change superbar icon, similar to windows live messenger.

    - by D Connors
    With seven's new superbar, windows live messenger is now able to display your status on the bar's icon (and not on the system tray). So that got me thinking, maybe a firefox extension could do something similar. Therefore, here's my question to those who understand the workings and spinning wheels behind firefox extensions: could a firefox extension change the superbar icon to display some useful info? Does the current functionality support it? EDIT: I think my question is not really clear. I just want to know if it's theoritically possible for a firefox addon to change the superbar icon dinamically. For instance, windows live messenger changes the icon acording to your status, and gmail notifier plus changes the icon according to your unread messages count. I'm just wondering if firefox as it is right now supports an extension with that functionality. I know that no current extensions do it, and I'm not looking for a gmail notifier (that was just an example). thanks

    Read the article

  • Cannot add VMDK to VM that was cloned with FlexClone

    - by Daniel Lucas
    I have a virtual machine called VM-A with two VMDK's on volume VOL-A. Call these VMDK-1 (system) and VMDK-2 (data). I want to clone VMDK-2 and attach that clone to VM-A as a new disk, but I'm getting an error. Here are my steps: I use the following command to clone : clone start /vol/VOL-A/VMDK-2 /vol/VOL-A/VMDK-3 Run clone status which shows successful and I can see the new file in the volume In vCenter I edit the settings of VM-A and try to add VMDK-3, but get the following error: Failed to add disk scsi0:4, Failed to power on scsi0:4 I've tried adding this cloned disk to other VMs and get the same error. What could be the issue? My specs are below. NetApp FAS 2040 Data ONTAP 8.0.1 vSphere ESXi 4.1 vCenter Server 4.1 Thanks, Daniel

    Read the article

  • Intel VT-x disappeared after upgrading to Windows 8

    - by StepTNT
    I've upgraded to Windows 8 some weeks ago (MSDNAA!) and today, while I was trying to run a VM, I've noticed that VT-x is disabled. Now, Hyper-V works without problems, as I've tried emulating Win7 and WP8; but VirtualBox says that VT-x is disabled and it can't run my VM. Just to double check, I've run Securable by GRC and the Intel utility and both says that I've got VT-x off. Here comes the problem: VT-x is ON in my BIOS, and it worked flawlessly before upgrading to Windows 8! Any kind of suggestion? EDIT: My CPU supports VT-x: http://ark.intel.com/products/52219

    Read the article

  • Computer starts, POSTs normal, no video

    - by Annath
    So, I recently tried to start up an old computer of mine. It would not power on, so I replaced the PSU. When I powered it on, all the fans spun up and the POST beeps indicated a normal startup. The problem was there was no video output. Every couple of minutes, I hear the post code again. I think it is restarting after POST, but without video I have no idea why. Does anyone have an idea as to why this is happening, and how to fix it? EDIT: The video card is a PCI-e card. There is no integrated graphics on the motherboard. If I remove the video card, the POST indicates a missing card. When I put it back, it goes back to normal, so I know that it recognizes that the card exists.

    Read the article

  • Tape Storage - How do I setup a tape backup system for use with my NAS

    - by John Himmelman
    I currently have a QNAP NAS with a raid 5 config (~600gb storage) but don't have a reliable backup solution. I've heard great things about tape backup systems (reliability, durability, etc..). How can I go about setting up a tape backup system? The tape drives seem very expensive (1k+ for a decent one, more than the price of my NAS). What are the important specs to compare and features to take into consideration? Edit: Does anyone have links to some good resources? There is a ton of articles, guides, and sites on this subject, not sure where to start.

    Read the article

  • How to add authentication to ssh dynamic port forwarding?

    - by Aalex Gabi
    I am using ssh as a SOCKS server by running this command on the server: ssh -f2qTnND *:1080 root@localhost There is one problem: anybody can connect to the server and use it's internet connection. Options: To use iptables to filter access to the server, but I connect to the server from various non-statically allocated IP addresses so I would have to edit very frequently those filters which can be annoying. To install a SOCKS server on the remote. Ultimately this is the last option if there is no other simpler way to do it. (I am very lazy) Launching the same command on clients machines. The problem here is that some clients don't run on Linux and it is awkward to set up the tunnel (Windows + Putty). Is there a way to add authentication to a SOCKS server made using ssh? Bonus question: How to add encryption between the client and the server (made using ssh)?

    Read the article

  • Abstract exception super type

    - by marcof
    If throwing System.Exception is considered so bad, why wasn't Exception made abstract in the first place? That way, it would not be possible to call: throw new Exception("Error occurred."); This would enforce using derived exceptions to provide more details about the error that occurred. For example, when I want to provide a custom exception hierarchy for a library, I usually declare an abstract base class for my exceptions: public abstract class CustomExceptionBase : Exception { /* some stuff here */ } And then some derived exception with a more specific purpose: public class DerivedCustomException : CustomExceptionBase { /* some more specific stuff here */ } Then when calling any library method, one could have this generic try/catch block to directly catch any error coming from the library: try { /* library calls here */ } catch (CustomExceptionBase ex) { /* exception handling */ } Is this a good practice? Would it be good if Exception was made abstract? EDIT : My point here is that even if an exception class is abstract, you can still catch it in a catch-all block. Making it abstract is only a way to forbid programmers to throw a "super-wide" exception. Usually, when you voluntarily throw an exception, you should know what type it is and why it happened. Thus enforcing to throw a more specific exception type.

    Read the article

  • How do I pipe a list of numbers straight from the shell into a command?

    - by learnvst
    How do I pipe a list of numbers straight from the shell into a command? For exampe something like this [1,2,3,4] | sort would give 1 2 3 4 EDIT: In response to the answers kindly posted so far . . . I ask this, because I want to quickly test and debug a console application that takes many numbers as it input without having to type lots of individual values followed by carriage returns. I'd like to just type in the 'one liner' and hit the up arrow now and then to replay the command. Ideally, I'd like to do this without using a text file containing the values (which would obviously be the most simple way to do this.)

    Read the article

  • Cannot get webapps to work after upgrade from 12.04 to 12.10

    - by kashan
    I just upgraded to Ubuntu 12.10 from 12.04. But I cannot use WebApps. In fact there is no sign of them anywhere. Firefox and Chromium are not prompting for integration. I tried re-installing both browsers/webapps plugin of each, but no luck. Out of curiousity, I tried to install unity-webapps-preview through terminal, apt-get reported that this operation is going to need 127mb. After installation, restarting session, nothing. I re-ran the unity-webapp-preview in terminal and SURPRISINGLY it again asked me that this operation is going to need 58mb. After Installation, nothing. Firefox is showing the unity-webapp plugin in Extensions but in Preferences there is noting like Unity settings or options for exceptions in General tab (as I seen in some threads). Chromium is not even showing the plugin in Extensions nor in the settings. Really need help. I know there is a reported bug but it is mostly about the complains that the webapps are not working as they should but in my case they don't seem to exist. EDIT: The out put of gsettings list-recursively | grep webapp is: com.canonical.unity.webapps allowed-domains @as [] com.canonical.unity.webapps dontask-domains @as [] com.canonical.unity.webapps index-update-time 43200 com.canonical.unity.webapps integration-allowed true com.canonical.unity.webapps preauthorized-domains ['amazon.ca', 'amazon.cn', 'amazon.com', 'amazon.co.uk', 'amazon.de', 'amazon.es', 'amazon.fr', 'amazon.it', 'www.amazon.ca', 'www.amazon.cn', 'www.amazon.com', 'www.amazon.co.uk', 'www.amazon.de', 'www.amazon.es', 'www.amazon.fr', 'www.amazon.it', 'one.ubuntu.com']

    Read the article

  • 19" Rackmountable fast storage arrays

    - by Eruditass
    I'm in need of some fast (15+ GB/s write) and somewhat large (50 TB+) storage subsystem with a standard storage interface. I'd prefer something other than Fibre Channel, which admittedly appears to be the most standard interface. RAID 5 is sufficient. What are the cheapest / smallest products from vendors to look at for building this subsystem? I've looked at DDN and TMS so far. Small: Under 20U Cheap: Under a million Edit: I'd really like to cut back costs as much as possible at the expense of capacity. How cheap can these bandwidth requirements be met?

    Read the article

  • DNS - Redirect from old server to new.

    - by jyoseph
    I have a server, (Server A) Windows Server 2003 that I was hosting some sites on. Now they are hosted on a different server (Server B). I recently switched the DNS at godaddy to point to the new nameservers. Is there something I can do on Server A to point all requests to Server A to Server B (basically a redirect from Server A to B)? What type of record would that be? This is while I'm waiting for the DNS changes I made to fully resolve. edit To further clarify. test.com may still be resolving to Server A, I'd like a DNS record on Server A that tells it to go to the new server. Is that possible?

    Read the article

  • IIS 7 503 error, application pool stop crash, defdoc.dll could not be loaded due to a configuration

    - by optician
    Hi All, Currently trying to get iis 7 to work, but every time I request a page, the application pool goes into stopped status. In the event log this is what comes back. The Module DLL 'C:\Windows\System32\inetsrv\defdoc.dll' could not be loaded due to a configuration problem. The current configuration only supports loading images built for a x86 processor architecture. The data field contains the error number. I've already re installed iis, any other ideas, I read that someone fixed this by downloading the dll again, but this seems like an odd solution. Thanks. EDIT I have now replaced the file with one I downloaded off the internet, and now it says The Module DLL 'C:\Windows\System32\inetsrv\protsup.dll' could not be loaded due to a configuration problem. I hope I don't have to get 100's of these.

    Read the article

  • printable PHP manual - 'all but the Function Reference section'

    - by JW01
    My Motivation I find it easier to learn things by reading 'offline'. I'd like to lean back and read the narrative part of a paper version of the official php manual. My Scuppered Plan My plan was to download the manual, print all but the Function Reference section and then read it. I have downloaded the "Single HTML file" version of the manual from the php.net download page. (That version did not contain any images, so I patched-in the ones from the Many HTML files version with no problem.) My plan was to open that "Single HTML file" in an HTML editor, delete the Function Reference section then print it out. Unfortunately, although I have tried three different editors, I have not been able to successfully load-up that massive html file to be able to edit it. Its about (~40MB). I started to look into the phpdoc framework with a view to rendering my own html docs from the source...but that's a steep learning curve for a newby..and is a last resort. I would use a file splitter, but they tend to split files crudely with no regard for html/xml/xhtml sematics. So the question is... Does anyone know know where you can download the php manual in a version that is a kind of half-way house between the 'Single HTML file' and the 'Many HTML files'? Ideally with the docs split into 3 parts: File 1 - stuff before the function reference File 2 - function reference File 3 - stuff after the function reference Or Can you suggest any editors/tools will enable me to split up this file myself?

    Read the article

  • Viewing CHM Files Across The Network in Windows 7

    - by Lukas Cenovsky
    When I try to open .chm help from a network shared drive I receive the following error: Navigation to the webpage was canceled. I know about the .reg solution described on KB896054 [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\HTMLHelp\1.x\ItssRestrictions] "MaxAllowedZone"=dword:00000001 but it does not work in Windows 7. Any ideas how to make .chm help available from the network drives? Edit: I have the network path mapped to P: drive letter. My program runs from P: and I want to see the help for it. Copying the program to local drive is not a solution for me.

    Read the article

  • centos: nginx + thin webserver, incoming connections not allowed

    - by cbrulak
    I setup a fresh CentOS 5 install, compile nginx from scratch and am using thin as the rails server. If I visit the ip adress on the LAN: (for example) 1.2.3.4 I get the website not found error. However, I can ssh into the machine. If I use links to visit the ip address, I get the landing page. Any suggestions? Thanks EDIT I ran system-config-securitylevel and then was able to change the security settings to allow incoming connections.

    Read the article

  • Did Firefox running in OSX get hacked

    - by z-buffer
    When I try to do a google search in Firefox, I can't click on any of the links. They're just regular black text, not hyperlinks. I even tried safe mode and disabling all the plugins. I was running Firefox 12. I installed the current version over it and it's the same thing. Other browsers have not been affected. This is what it looks like. Edit: My firewall was turned off and I had several things running which are potential security holes. I turned on my firewall and closed all unnecessary ports. I also turned off Home Sharing. Then I restarted my computer. After that, Firefox works normally again. What do you think happened?

    Read the article

  • Best Practices for MVC Architecture

    - by Mystere Man
    There are a number of questions on StackOverflow regard MVC best practices, but most of those seem to revolve around things like using Dependancy Injection, or creating helper functions, or do's and don'ts of what to do in views and controllers. My question is more about how to architect an MVC application. For example, we are encouraged to use DI with the Repository pattern to decouple data access from the controller, however very little is said on HOW to do that specifically for MVC. Where would we place the Repository classes, for instance? They don't seem to be model related specifically, since the model should likewise be relatively decoupled from the actual data access technologies. A second question involves how to structure the layers or tiers. Most example applications (Nerd dinner, Music Store, etc..) all seem to use a single tier, 2 layer approach (not counting tests) that typically has controllers directly calling L2S or EF code. If I want to create a multi-tier/layer aplication what are some of the best practices there in regards to MVC? This question is one-part standard q-a, but another part best-practices, so it could go either here or programmers.se, I am marking it CW. If you feel it would be better suited to programmers.se then it can be migrated. EDIT: What happened to the Community Wiki option? It seems to be gone.

    Read the article

  • Conditionally create symbolic link by filesize using find exec ubuntu 10.04

    - by jmlw
    I have an interesting problem. I'm trying to create symbolic links in a single folder, for all files in a directory which are larger than a specified size. For clarification, here is an example: /Files /Large_Files /LargeFile1_symlink /LargeFile2_symlink /Folder1 /file_a /file_b /Folder2 /LargeFile1 /Folder3 /LargeFile2 /file_c What I have so far to try to accomplish this is: find -size +102400 -exec ln -s $PWD/{} Large_Files/ \; However, this find produces ./LargeFile1 So my symlink command produces ln -s /Files/Folder2/./LargeFile1 Large_Files/ My question is, would it be possible to use the basename command to separate out only the filename so this command will work? Or does anybody have a suggestion on how to do this without writing a script, or give me an example on writing a script? I've never done scripting before, but I do know Java, but don't want to take the time to do all this in Java. Thank you for any help! Edit: adding tags

    Read the article

< Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >