Search Results

Search found 19471 results on 779 pages for 'network troubleshooting'.

Page 277/779 | < Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284  | Next Page >

• Connecting to a VirtualBox machine from the host, using an ip address

  - by Doron

  Hello, In a macbook host, I run VirtualBox having a guest ubuntu server, with a NAT network setting. In the virtual machine application "Parallels", I would get on the host an IP address of the guest, to which I could later set hostnames and access it directly. However, I couldn't find a way to accomplish this using VirtualBox. The only solution VirtualBox has for me, is to set port forwarding, and access "localhost" with these ports. How can I have the desired behavior set up, without having to change to a bridged network settings, and expose my guest computer to the network my host computer is connected to ? Thanks.

  Read the article

• Macbook Air freezes while running Ubuntu 13.10

  - by jjesse

  Ok folks I'm trying to setup my Macbook Air to run Ubuntu 13.10 (note: I normally using Kubuntu but currently running Ubuntu). I have run all of the updates for the system as of this posting. This happens regardless of the application I have open (Firefox, Terminal, Software Updater). The system will freeze, become unresponsive and then kick me back to the login screen. I don't see a crash notification or anything to send as troubleshooting so I don't know where to start

  Read the article

• Which equipments should I buy for a laboratory?

  - by Hossein Margani

  Hi every body! I want to create a network of computers for a network laboratory in a university. I want to install windows on them. What is the fastest way for doing this and also which equipments I should buy for this laboratory. I also want to use this network as a computer laboratory, operating system laboratory, programming laboratory, microprocessor laboratory, computer architecture laboratory and software engineering laboratory. I should emphasis that this is a scholastic laboratory. Thanks.

  Read the article

• How to achieve reliable Gigabit Ethernet Link with my Acer Aspire Revo R3610?

  - by The Operator

  I want to stream HD movies over my wired Gigabit LAN from my PC to my Acer Aspire Revo R3610. It's connected with a 3ft Cat5e patch cable to my Netgear GS605v2 Switch. The PC acting as File Server is connected at 1Gbps to the Switch. Network driver options are set to defaults, including automatic speed/duplex negotiation on both machines. The Revo will not connect to my Network Switch at 1Gbps - the OS reports that it reverts to 100Mbps either shortly after connection or immediately upon connection. Through a process of elimination (trying different drivers, patch cables, ports on the switch, and other 1Gbps-capable devices connected to the Network switch which successfully achieve 1Gbps links and performance) I have drawn the conclusion there is either a Hardware or Software (Driver) issue with the Revo itself. I have performed tests using Windows 7 and Ubuntu 9.10. Can anyone offer insight on Gigabit Ethernet with the Revo?

  Read the article

• PDAnet on Android IP on PC is not public IP. Where does the NAT take place, PDAnet or Verizon?

  - by lcbrevard

  When using PDAnet on a PC (Win7 ultimate) to USB tether a Motorola Droid on Verizon 3G the IP address of the PC appears to be public - 64.245.171.115 (64-245-171-115.pools.spcsdns.net) - but connections show as coming from another public IP - 97.14.69.212 (212-sub-97.14.69.myvzw.com). Someone is performing Network Address Translation - either PDAnet or within the Verizon 3G network. Can someone tell me who is doing the NAT? Is it PDAnet or is it at Verizon? Is there any possibility of setting up port forwarding, such that connections to the public IP 97.14.69.212 (212-sub-97.14.69.myvzw.com) are forward to the PC? We are testing a network protocol that requires either a true public IP or forwarding a range of ports from the public Internet to the system on which the software runs (actually Linux hosted by VMware Player or Workstation on a PC running Windows).

  Read the article

• Methodology To Determine Cause Of User Specific Error

  - by user3163629

  We have software that for certain clients fails to download a file. The software is developed in Python and compiled into an Windows Executable. The cause of the error is still unknown but we have established that the client has an active internet connection. We suspect that the cause is due to the clients network setup. This error cannot be replicated in house. What technique or methodology should be applied to this kind of specific error that cannot be replicated in house. The end goal is to determine the cause of this error so we can move onto the solution. For example; Remote Debugging: Produce a debug version of the software and ask the client to send back a debug output file. This involves alot of time (back and forth communication) and requires the client to work and act in a timely manor to be successful. In-house debugging: Visit the client and determine their network setup, etc. Possibly develop a series of script tests before hand to run on the clients computer under the same network. Other methodologies and techniques I am not aware of?

  Read the article

• Built-In SQL Server Agent Performance Reports in SQL Server 2005

  SQL Server 2005 includes a number of built-in reports to assist you in troubleshooting and measuring performance. In this tip I will cover the Built in SQL Server Performance Reports related to SQL Server Agent within SQL Server 2005.

  Read the article

• Windows VPN not authenticating from ADSL to Wireless link

  - by deanvz

  I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

  Read the article

• Linksys router with multiple external IP's

  - by Adrian Mester

  In an office I've got a network connection with 5 external IPs and a Linksys router (I'm not 100% percent sure of the model). I need 4 of those 5 IPs to be routed to a server, and the fifth to be shared between the other computers at the office. This can probably be done using a switch in front of the router. Connect the server and the router to the switch, and let the router handle the rest of the network. Is there a way to configure the router to route the 4 IPs to the server, and create an internal network the the other computers at the same time?

  Read the article

• When connected through a router, a new gateway appears, and I lose my internet connection.

  - by idan315

  I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. (Just to be clear: the computer using Windows XP can connect to the internet without any problem). This entire question is about the PC using Windows 7. The only symptom of this problem is that when I see my network devices, in addition to my router (which appears as "Network 4", or something of the sort), I also see an "Unidentified Network". When using ipconfig to check the problem, I see a second gateway, with the IP 0.0.0.0, in addition to the IP of my router.

  Read the article

• Why can't anyone else access my website in IIS on Windows 7?

  - by Rod

  I've got an ASP.NET application that I have in IIS on my Windows 7 Ultimate machine. I've tested it from that machine and it works fine. This machine is in my home network, a simple peer-to-peer network. The strange thing is that no one else in my network can access that website. Why is that? There are other Windows 7 machines here, and they're all in the some homegroup. When I attempt to access the website on my machine from one of the other machines, it fails and that's it. So, what's wrong?

  Read the article

• Significant OS X Finder lag when listing directories/files

  - by Jack Sleight

  I'm experiencing some significant OS X finder lag, that seems to be purely an issue with Finder itself, and not the HD or any other part of OS X (I'll explain below). The lag only appears to be when listing directories/files, where I'm seeing up to twelve or so seconds of lag (the folder opens with a blank list and the spinner going in the bottom right). This happens with both the local SSD and network drives (connected via ethernet or wifi) Browsing both local and network drives in terminal and listing directories is instant I can actually browse files on my NAS from my phone over a 3G connection from the other side of the country faster than Finder can when connected to the local network (madness!) Can anyone help? Thanks.

  Read the article

• Microsoft Cluster or Oracle Fail Safe error

  - by osdm

  Trying to get Oracle Database 10g to work on Microsoft cluster (using Oracle Fail Safe, not RAC). Everything installed, but when trying to verify group or add database to group I get following error: FS-10220: Network name MSK00-NST01-1 maps to IP address 10.1.11.74 in the cluster resource but maps to IP address 10.1.1.74 on the system MSK00-NST01-1 is cluster name, 10.1.11.74 is first node IP, 10.1.1.74 is second node IP. Oracle documentation says "The cluster and the system must have the same IP address mapping for a network name. Check that either the network name server or the local host file has the same IP address mapping as the cluster." Where is the error - in Oracle configuration or in cluster configuration? What are possible ways to correct it? Thanks a lot for any ideas.

  Read the article

• Static IP Address on Ubuntu 12.04 Virtual Machine

  - by chrisnankervis

  I've setup a VM running Ubuntu 12.04 specifically for local web development and am having some problems ensuring it has a static IP address. A static IP address is important as I'm using the IP address in my hosts file to assign a .local suffix to addresses used both in browser and to connect to the correct database on the VM. Currently, every time I connect to a new network or my VM is assigned a new IP address I need to reconfigure my whole environment which is becoming quite a pain. It also probably doesn't help that the default-lease-time on the Ubuntu VM is set to 1800 by default. At the moment I'm using VMWare Fusion and the Network Adapter is enabled and set to "Autodetect" under Bridged Networking. I've tried to set a static IP address within the dhcpd.conf using the code below: host ubuntu { hardware ethernet 00:50:56:35:0f:f1; fixed-address: 192.168.100.100; } The fixed-address that I've used is also outside the range specified in the subnet block (which in this case is 192.168.100.128 to 192.168.100.254). I've tried adding and removing the network adapter and restarting my Mac after each time to no avail. Below is an ifconfig of the VM that might be of some help: eth0 Link encap:Ethernet HWaddr 00:50:56:35:0f:f1 inet addr:192.168.0.25 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fe35:ff1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1624 errors:0 dropped:0 overruns:0 frame:0 TX packets:416 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:147348 (147.3 KB) TX bytes:41756 (41.7 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Are there any specific issues with 12.04 that I'm missing? Otherwise has anyone else got any ideas? Thanks in advance.

  Read the article

• Internet access only works after turning off and on the local connection

  - by AgentFire

  Every time I turn on the computer, it has no internet access. The network card is connected to a router which broadcasts the internet all over the office LAN. Once I turn off and then on the local connection (or network card), the internet access works. Rebooting and logging out/in again does not help. Only the turning off and on the network card gives me internet access. Why is that? How do I fix it?

  Read the article

• Making internal website available publicly (Win 2008 Server)

  - by endigo

  I have an IIS 7 web site that is running on a Windows 2008 Server (64-bit) VMWare on a Windows 2008 Server (64-bit) Host on my local network. My router is a Firebox XEdge and it has port 80 directed to the IP of the server on VMWare. I can reach the web site from inside the network, but I cannot reach the site from outside the network. I have other web sites that are working through the Firebox, and I am confident that it is configured correctly. I suspect that Windows 2008 server is blocking routed or public addresses, but I have shut down the firewall on the Server that is running on VMWare and the AVG Anti-virus to no avail. How can I make my site available publicly.

  Read the article

• A website hosted on the 1.0.0.0/8 subnet, somewhere on the Internet?

  - by Dave Markle

  Background I'm attempting to demonstrate, using a real-world example, of why someone would not want to configure their internal network on the 1.0.0.0/8 subnet. Obviously it's because this is not designated as private address space. As of 2010, ARIN has apparently allocated 1.0.0.0/8 to APNIC (the Asia-Pacific NIC), who seems to have begun assigning addresses in that subnet, though not in 1.1.0.0/16, 1.0.0.0/16, and others (because these addresses are so polluted by bad network configurations all around the Internet). My Question My question is this: I'd like to find a website that responds on this subnet somewhere and use it as a counter-example, demonstrating to a non-technical user its inaccessibility from an internal network configured on 1.0.0.0/8. Other than writing a program to sniff all ~16 million hosts, looking for a response on port 80, does anyone know of a directory I can use, or even better yet, does anyone know of a site that's configured on this subnet? WHOIS seems to be too general of a search for me at this point...

  Read the article

• Configure ubuntu 12.10 to share internet through second NIC with subnetwork

  - by Dan Smith

  I have an Ubuntu 12.10 box with 2 NICs. eth0 is connected to my 192.168.1.X network, which is connected to my home router and out to the internet. I want the other interface, eth1,to support 10.0.0.x and allow devices on that network to access the internet through my ubuntu box. I do not need dhcp on the 10.0.0.x network. Here's a schematic: Internet --- home router ---- ubuntu[eth0:192.168.1.x, eth1:10.0.0.x] --- [10.0.0.x device] How do I configure the ubuntu box to share the internet with devices on that subnetwork? Thanks!

  Read the article

• Attempting to caue packet loss with netem doesn't work - possibly because of NAT (but delay does work)

  - by tomdee

  I have traffic from a WIFI access point routed via an Ubuntu box. I have two network interfaces which are NATed *filter :INPUT ACCEPT [11:690] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [37:6224] -A FORWARD -s 192.168.2.0/24 -i eth1 -o eth0 -m conntrack --ctstate NEW -j ACCEPT -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT COMMIT # Completed on Thu Mar 15 13:37:21 2012 # Generated by iptables-save v1.4.10 on Thu Mar 15 13:37:21 2012 *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -j MASQUERADE COMMIT If I run a ping app on an Android device connected to the WIFI network I can happily ping google. If I use netem to introduce some delay tc qdisc change dev eth0 root netem delay 100ms I can clearly see pings taking longer. If I use netem to introduce some packet loss tc qdisc change dev ifb0 root netem loss 50% then I see no change. Packet loss does work fine for locally generated traffic, just not for traffic coming in over the network that's being NATed. Any ideas how to sort this out?

  Read the article

• Ubuntu 11.10 Intel controller VGA detected but no signal

  - by Fred Zimmerman

  Ubuntu 11.10 Dell vostrum Intel® Sandybridge Mobile x86/MMX/SSE2 Displays ... correctly detects and identifies Viewsonic 27" VGA monitor, but monitor says it's receiving no signal Plugged into another monitor (Sony 20"), same result. $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) I've browsed these forums and tried everything that I can but nothing has worked. I need a stepwise troubleshooting plan.

  Read the article

• Can't ping IPs for devices not part of Windows Domain

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The DNS server is on a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. All machines either have a fixed or DHCP allocated IP on the 192.168.0.* subnet. How do I configure the DNS server or the Windows Domain so that Windows machines can see the iPhones?

  Read the article

• Track sales and commission with third-party tool

  - by Andrew

  I have a clothing website where I link to various clothing retailers. I have reached an agreement with one of the retailers whereby they will pay a commission to us for every sale they make from traffic that was referred by our site. I need a mechanism for tracking how much commission should be paid to us, that involves as little work as possible to implement from their side. We both have Google Analytics. Option 1: They record a goal in their GA account whenever someone makes a purchase on their site. They see how many completed goals are marked as referral traffic from our site and calculate commission accordingly. The problem with this is that the whole process of calculating and paying commission will be manual. They will need to frequently check how many sales were generated by referral traffic from our site, and probably we will have to chase them for commission payments. Also - since we won't have access to their GA data - we will need to trust that they report all sales accurately. Option 2: Sign them up to an affiliate network like Commission Junction or Google's Affiliate Network, and connect to them through this network. The problem with this solution is that it seems too heavyweight; ideally we don't want to ask a retailer to go through the whole sign up process just to deal with us and pay us commission. I am assuming that there must be some lightweight service that tracks the number of sales by one site and pays commission accordingly to the other site, where the sign up and installation procedure is simple and fast.

  Read the article

• Too many processes?

  - by Mophily

  VMware Fusion v3.0.1 One vm for Windows XP, converted and recently expanded the disk size. Mac OS X 10.5.8, 2 x 3 GHz dual-core intel xeon machine. Immediately after booting, and before VMware Fusion is launched, the Activity Monitor shows eight processes associated with "vm". What caught my eye is the duplicates: netifup and dhcpd. I noticed this while trying to re-establish network connectivity after the upgrade to 3.0.1. I am not sure when the network connection was clobbered, so I cannot say it happend during the upgrade. Is eight processes typcial? I expect about six, as listed in other notes and documents on the web site. Could this be related to the failure to connect to the network?

  Read the article

• setting up bridged adapter for VPN server

  - by B. VB.

  I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

  Read the article

• Remote Control Home PC from Corporate Work PC

  - by muncherelli

  Here is my situation: I am currently on a Windows XP workstation at work. I have an android tablet that I use to splashtop into my home PC. I would like to be able to use my work keyboard and mouse to control my home PC while I am splashtop'd into it using my tablet. My work PC is on a corporate LAN, and not on the same network as my tablet. The company I work for provides wifi for personal devices, but they are not accessable to the internal network. I thought about going the Synergy route, however that would require my home PC to be able to connect to my work PC which isn't really possible. The opposite would work though, if I could reverse connect the server to the client, but the Synergy software doesn't really support that. I do have a couple linux boxes running at home, so I can ssh into my home network and tunnel ports via SSH if needed. With what I have, how can I accomplish seamless keyboard and mouse sharing between my work PC and either my home PC or my android tablet?

  Read the article

< Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284  | Next Page >