Search Results

Search found 8766 results on 351 pages for 'integrated authentication'.

Page 279/351 | < Previous Page | 275 276 277 278 279 280 281 282 283 284 285 286  | Next Page >

• Apache httpd LDAP integration

  - by David W.

  I am configuring a CollabNet Subversion integration. I have the following collabnet_subversion.conf file: <Location /svn> DAV svn SVNParentPath /mnt/svn/new_repos SVNListParentPath on AuthName "VegiBanc Source Repository" AuthType basic AuthzLDAPAuthoritative off AuthBasicProvider ldap AuthLDAPURL ldap://ldap.vegibanc.com/dc=vegibanc,dc=com?sAMAccountName" NONE AuthLDAPBindDN "CN=SVN-Admin,OU=Service Accounts,OU=VegiBanc Users,OU=vegibanc,DC=vegibanc,DC=com" AuthLDAPBindPassword "swordfish" </Location> This works great. Any user in our Active Directory can access our Subversion repository. Now, I want to limit this to only people in the Active Directory group Development: <Location /svn> DAV svn SVNParentPath /mnt/svn/new_repos SVNListParentPath on AuthName "VegiBanc Source Repository" AuthType basic AuthzLDAPAuthoritative off AuthBasicProvider ldap AuthLDAPURL ldap://ldap.vegibanc.com/dc=vegibanc,dc=com?sAMAccountName" NONE AuthLDAPBindDN "CN=SVN-Admin,OU=Service Accounts,OU=VegiBanc Users,OU=VegiBanc,DC=vegibanc,DC=com" AuthLDAPBindPassword "swordfish" Require ldap-group CN=Development OU=Security Groups OU=VegiBanc, dc=vegibanc, dc=com </Location> I added Require ldap-group, but now no one can log in. I have LogLevel set to debug, but all I get is this in my error_log (Single line broken up for easier reading): [Thu Oct 11 13:09:28 2012] [info] [client 10.55.9.45] [6752] vauth_ldap authenticate: user dweintraub authentication failed; URI /svn/ [ldap_search_ext_s() for user failed][Bad search filter] And, I get this in my access_log: 10.55.9.45 - - [11/Oct/2012:13:09:27 -0500] "GET /svn/ HTTP/1.1" 401 401 10.55.9.45 - dweintraub [11/Oct/2012:13:09:28 -0500] "GET /svn/ HTTP/1.1" 500 535 Yes, I am in that group. (Or, at least how can I confirm that just to make sure that's not the issue. I have the SysinternalsSuite ADExplorer. It's where I'm getting all of my info.)

  Read the article

• AuthBasicProvider: failover not working when the first LDAP is down?

  - by quanta

  I've been trying to setup redundant LDAP servers with Apache 2.2.3. /etc/httpd/conf.d/authn_alias.conf <AuthnProviderAlias ldap master> AuthLDAPURL ldap://192.168.5.148:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> <AuthnProviderAlias ldap slave> AuthLDAPURL ldap://192.168.5.199:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> /etc/httpd/conf.d/authz_ldap.conf # # mod_authz_ldap can be used to implement access control and # authenticate users against an LDAP database. # LoadModule authz_ldap_module modules/mod_authz_ldap.so <IfModule mod_authz_ldap.c> <Location /> AuthBasicProvider master slave AuthzLDAPAuthoritative Off AuthType Basic AuthName "Authorization required" AuthzLDAPMemberKey member AuthUserFile /home/setup/svn/auth-conf AuthzLDAPSetGroupAuth user require valid-user AuthzLDAPLogLevel error </Location> </IfModule> If I understand correctly, mod_authz_ldap will try to search users in the second LDAP if the first server is down or OpenLDAP on it is not running. But in practice, it does not happen. Tested by stopping LDAP on the master, I get the "500 Internal Server Error" when accessing to the Subversion repository. The error_log shows: [11061] auth_ldap authenticate: user quanta authentication failed; URI / [LDAP: ldap_simple_bind_s() failed][Can't contact LDAP server] Did I misunderstand?

  Read the article

• error in auth.log but can login; LDAP/PAM

  - by Peter

  I have a server running OpenLDAP. When I start a ssh-session I can log in without problems, but an error appears in the logs. This only happens when I log in with a LDAP account (so not with a system account such as root). Any help to eliminate these errors would be much appreciated. The relevant piece from /var/log/auth.log sshd[6235]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=example.com user=peter sshd[6235]: Accepted password for peter from 192.168.1.2 port 2441 ssh2 sshd[6235]: pam_unix(sshd:session): session opened for user peter by (uid=0) pam common-session session [default=1] pam_permit.so session required pam_unix.so session optional pam_ldap.so session required pam_mkhomedir.so skel=/etc/skel umask=0022 session required pam_limits.so session required pam_unix.so session optional pam_ldap.so pam common-auth auth [success=1 default=ignore] pam_ldap.so auth required pam_unix.so nullok_secure use_first_pass auth required pam_permit.so session required pam_mkhomedir.so skel=/etc/skel umask=0022 silent auth sufficient pam_unix.so nullok_secure use_first_pass auth requisite pam_succeed_if.so uid >= 1000 quiet auth sufficient pam_ldap.so use_first_pass auth required pam_deny.so pam common-account account [success=2 new_authtok_reqd=done default=ignore] pam_ldap.so account [success=1 default=ignore] pam_unix.so account required pam_unix.so account sufficient pam_succeed_if.so uid < 1000 quiet account [default=bad success=ok user_unknown=ignore] pam_ldap.so account required pam_permit.so account sufficient pam_ldap.so account sufficient pam_unix.so

  Read the article

• windows 8.1 does not boot after CHKDSK command

  - by sepehr

  I had problem with Windows 8.1 high Disk usage so in order to solve , searched forums. A voted answer suggested to use CHKDSK command as follow: run command prompt and as administrator type code snippet below: CHKDSK /f /v /b C: (I can not remember accurately) CHKDSK printed : can not run CHKDSK right now , would you like to schedule C drive to be checked next time windows starts? (Y/N) my response was "Y" ,please ! Following this suggestion not only didn't solve my problem as expected but also added another one ! The next time system booted, after windows authentication I just could see a black screen and mouse pointer. So I force shut downed the system and tried to start windows again. This time , windows got stuck in Scanning and Repairing on 22% for around 3 hours so I got tired and forced shut downed again. is CHKDSK source of Scanning and Repairing problem or they are discrete ? is there any hope to overcome this problem without re-installing windows ? can any one else run CHKDSK on newer versions of windows without problem? is CHKDSK effective but inefficient ?(it finally get to end but will take a long time) If yes, how much time does it take? I also have Linux Ubuntu 14.04 installed along side windows.

  Read the article

• Can't connect to public WiFi with MacBookPro at coffee shops and libraries

  - by Nathan Bowers

  The Problem: I can't connect to public, unencrypted WiFi at my local public library or Peets Coffee. My Setup: Late 2006 MacBookPro running 10.5.8. I have Parallels installed. It's supposed to work like this: 1) Connect to their unencrypted WiFi network 2) Open a browser which redirects you to their "enter password/agree to terms" page. 3) Browse normally. I can connect to the WiFi network, but when I try to authenticate I always get stuck in a redirect loop. It's been like this for a while. Even before I upgraded to 10.5.8. I never have trouble with encrypted networks or regular open WiFi. What I've tried: Disabling Parallels connections in Network Prefs. Superstition: somehow Parallels installed something in the network stack that's messing me up. Pinging the IP address of the WiFi node I'm connected to. I can ping it, it's there, but I still get stuck in this authentication redirect loop. Tried different browsers, tried different cookie and security settings. Even tried IE under Parallels. No dice. Tried flushing DNS cache. Asked library and coffee employees for help. It didn't go well. My Question: Anybody else have this problem? What should I be looking for?

  Read the article

• Postfix Relay to Office365

  - by woodsbw

  I am trying to setup a Postfix server on a Linux box to relay all mail to our Office365 (Exchange, hosted by Microsoft) mail server, but, I keep getting an error regarding the sending address: BB338140DC1: to= relay=pod51010.outlook.com[157.56.234.118]:587, delay=7.6, delays=0.01/0/2.5/5.1, dsn=5.7.1, status=bounced (host pod51010.outlook.com[157.56.234.118] said: 550 5.7.1 Client does not have permissions to send as this sender (in reply to end of DATA command)) Office 365 requires that the sending address in the MAIL FROM and From: header be the same as the address used to authenticate. I have tried everything I can think of in the config to get this working. My postconf -n: append_dot_mydomain = no biff = no config_directory = /etc/postfix debug_peer_list = 127.0.0.1 inet_interfaces = loopback-only inet_protocols = all mailbox_size_limit = 0 mydestination = xxxxx, localhost.localdomain, localhost myhostname = localhost mynetworks = 127.0.0.0/8 recipient_delimiter = + relay_domains = our.doamin relayhost = [pod51010.outlook.com]:587 sender_canonical_classes = envelope_sender sender_canonical_maps = hash:/etc/postfix/sender_canonical smtp_always_send_ehlo = yes smtp_sasl_auth_enable = yes smtp_sasl_mechanism_filter = login smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = smtp_tls_CAfile = /etc/postfix/cacert.pem smtp_tls_loglevel = 1 smtp_tls_security_level = may smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes sender_canonical: www-data [email protected] root [email protected] www-data@localhost [email protected] root@localhost [email protected] Also, sasl_passwd is set to the correct credentials (tested them using swaks multiple times.) Authentication works, and sends the message when the from headers are correct (also tested using swaks....which works) The emails are coming from PHP, so I have also tried altering the sendmail path in php.ini to use pass the correct from address via -f So, for some reason, mail coming from www-data and root are not having the from fields rewritten to Office 365's satisfaction, and it won't send the message. Any postfix gurus out there that can help me setup this relay?

  Read the article

• OS X Keeps prompting me for SSH private key passphrase (OS X 10.6.8)

  - by Danny Englander

  I have a private key to ssh into my server and the connection works. In my hosts file I have: Host myhost HostName xxx.xxx.xxx.xx GlobalKnownHostsFile ~/.ssh/known_hosts port 22 User myuser IdentityFile ~/.ssh/mykey_dsa IdentitiesOnly yes .. and then I type ssh myhost Every time I connect, I get the Mac OS X keychain prompt and I tell OS X to remember the passphrase but then when I disconnect from ssh and re-connect, I am prompted to add the passphrase to the keychain again. This is only a recent problem so I suspect and issue with Keychain? To be clear, I can 're-add' to keychain every time and connect but this defats the purpose. The permissions on my dsa key are set at 600 or -rw-------@ I tried repairing disk permissions but that did no good. My Google-foo is also failing me, nothing of use came up. So I am not sure if this an OS X / keychain issue or an SSH issue. update: When I try ssh -vvv myhost, I think it reveals the issue: debug1: Trying private key: /Users/danny/.ssh/mykey_dsa debug1: PEM_read_PrivateKey failed debug1: read PEM private key done: type <unknown> debug3: Not a RSA1 key file /Users/danny/.ssh/mykey_dsa. debug1: read PEM private key done: type DSA Identity added: /Users/danny/.ssh/mykey_dsa (/Users/danny/.ssh/mykey_dsa) debug1: read PEM private key done: type DSA debug3: sign_and_send_pubkey debug2: we sent a publickey packet, wait for reply debug1: Authentication succeeded (publickey). ... and after that I get connected. I think this crux of the matter is: PEM_read_PrivateKey failed

  Read the article

• Why does Windows 7 always automatically change the input or keyboard language?

  - by B-Ball

  I am wondering why Windows 7 always automatically changes my input or keyboard language. I've a notebook with an integrated QWERTY keyboard English (United States). Traveling, I use that one but, additionally, I've my own as well as a much better keyboard at home which is a QWERTZ keyboard German (Germany). Thus, being at home, I'd like to use my QWERTZ keyboard. Unfortunately, Windows 7 does not play along at this one. Every time, I start up my notebook, it is usually set to English (United States) but that's not the problem. In case, I'd use my notebook QWERTY keyboard English (United States), that's fine. However, if I start up my notebook and I'd like to use my QWERTZ keyboard German (Germany), I usually press ALT + Left Shift in order to switch from English (United States) to German (Germany) and Windows 7 switches the input language but only for the program that is currently open. If my input language is set to German (Germany) and I, e.g., open NotePad, Windows 7 automatically switches my input language to English (United States). This is very annoying since I've to change the input or keyboard language to German (Germany) every time I open up a new program. Why doesn't Windows 7 stay with one input language if I changed it manually by pressing ALT + Left Shift? Why doesn't the manual change of the input or keyboard language apply for the whole Windows 7? Why does it only affect the currently opened program? Since I've two keyboards with two different layouts, I seriously need to have both of the keyboards languages installed. I tried both of the below settings in order to find a solution for my problem. Currently, I am using the first option, two input languages. First option: two input languages: Second option: two keyboard languages:

  Read the article

• NetApp NDMP backup with BE 2010 R2 works, restore fails

  - by uuwe

  Hi, I'm having some issues with a new Backup Exec 2010 R2 installation. I configured a NetApp FAS2020 as an NDMP device and want to backup files from the NAS to a tape drive connected to my backup server. I set up ndmpd according to this document (http://www.symantec.com/business/support/index?page=content&id=TECH48957) and created a separate backup user (http://filers.blogspot.com/2006/09/setting-veritas-netbackup-with-non.html). Backup works perfectly, but restoring any file gives me an authentication failed error. The NDMP device has a "global" ndmp user configured in the device tab (tried this with the newly created ndmpd backup user and the netapp root) and I can also configure separate resource credentials in the BE restore job. I have tried setting the same accounts for the "global" ndmp device and the restore credentials and have also tried setting different accounts for them. NDMP debug level is at 5 and this is what shows up in /etc/messages. The session is closed immediately after it has been granted. 16:12:07 PST [Java_Thread:info]: ndmpdserver: ndmpd.access allowed for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 16:12:07 PST [Java_Thread:info]: Ndmpd51: ndmpd session closed successfully for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 Running wireshark on the backup server doesn't produce much. It shows a SYN - SYN/ACK - NDMP CONNECT_CLOSE Request from the backup server. The Resource Credentials for the restore job behave very oddly. If I enter NDMP credentials and do "Test All" it fails. If I use my regular domain backup account, it is successful. There are no failed or succeeded logons in the NetApp ndmp log and tracing this check shows that it doesn't even connect to the NAS. This makes me think that this is more likely flaky BE behaviour rather than misconfiguration of the NAS. Here is the options ndmp output: FAS2020-1 options ndmp ndmpd.access all ndmpd.authtype challenge ndmpd.connectlog.enabled on ndmpd.enable on ndmpd.ignore_ctime.enabled off ndmpd.offset_map.enable on ndmpd.password_length 16 ndmpd.preferred_interface disable ndmpd.tcpnodelay.enable off

  Read the article

• Upgrading Redmine, activerecord-mysql2-adapter not recognized

  - by David Kaczynski

  For upgrading Redmine from 1.0.1 to 2.1.2, I need to execute the command: rake db:migrate RAILS_ENV=production However, doing so produces the following error: rake aborted! Please install the mysql2 adapter: gem install activerecord-mysql2-adapter (mysql2 is not part of the bundle. Add it to Gemfile.) I have ran gem install activerecord-mysql2-adapter, but I still get the same error when I try to run the rake ... command. How do I get my RoR app to recognize that I have the mysql2 adapter installed already? or Is there something wrong with my activerecord-mysql2-adapter installation? Results of sudo bundle install: Using rake (10.0.0) Using i18n (0.6.1) Using multi_json (1.3.7) Using activesupport (3.2.8) Using builder (3.0.0) Using activemodel (3.2.8) Using erubis (2.7.0) Using journey (1.0.4) Using rack (1.4.1) Using rack-cache (1.2) Using rack-test (0.6.2) Using hike (1.2.1) Using tilt (1.3.3) Using sprockets (2.1.3) Using actionpack (3.2.8) Using mime-types (1.19) Using polyglot (0.3.3) Using treetop (1.4.12) Using mail (2.4.4) Using actionmailer (3.2.8) Using arel (3.0.2) Using tzinfo (0.3.35) Using activerecord (3.2.8) Using activeresource (3.2.8) Using coderay (1.0.8) Using fastercsv (1.5.5) Using rack-ssl (1.3.2) Using json (1.7.5) Using rdoc (3.12) Using thor (0.16.0) Using railties (3.2.8) Using jquery-rails (2.0.3) Using metaclass (0.0.1) Using mocha (0.12.3) Using mysql (2.8.1) Using net-ldap (0.3.1) Using pg (0.14.1) Using ruby-openid (2.1.8) Using rack-openid (1.3.1) Using bundler (1.2.1) Using rails (3.2.8) Using rmagick (2.13.1) Using shoulda (2.11.3) Using sqlite3 (1.3.6) Using yard (0.8.3) [32mYour bundle is complete! Use `bundle show [gemname]` to see where a bundled gem is installed.[0m Results of sudo find / -name "*mysql2*": /var/lib/gems/1.8/doc/mysql2-0.3.11 /var/lib/gems/1.8/doc/activerecord-3.2.9/ri/ActiveRecord/Base/mysql2_connection-c.ri /var/lib/gems/1.8/doc/activerecord-mysql2-adapter-0.0.3 /var/lib/gems/1.8/doc/activerecord-mysql2-adapter-0.0.3/ri/ActiveRecord/Base/em_mysql2_connection-c.ri /var/lib/gems/1.8/doc/activerecord-mysql2-adapter-0.0.3/ri/ActiveRecord/Base/mysql2_connection-c.ri /var/lib/gems/1.8/gems/mysql2-0.3.11 /var/lib/gems/1.8/gems/mysql2-0.3.11/spec/mysql2 /var/lib/gems/1.8/gems/mysql2-0.3.11/mysql2.gemspec /var/lib/gems/1.8/gems/mysql2-0.3.11/lib/mysql2.rb /var/lib/gems/1.8/gems/mysql2-0.3.11/lib/mysql2 /var/lib/gems/1.8/gems/mysql2-0.3.11/lib/mysql2/mysql2.so /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2 /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2/mysql2.so /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2/mysql2_ext.c /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2/mysql2_ext.h /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2/mysql2_ext.o /var/lib/gems/1.8/gems/activerecord-3.2.9/lib/active_record/connection_adapters/mysql2_adapter.rb /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3 /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/activerecord-mysql2-adapter.gemspec /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/arel/engines/sql/compilers/mysql2_compiler.rb /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/activerecord-mysql2-adapter.rb /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/activerecord-mysql2-adapter /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/active_record/connection_adapters/em_mysql2_adapter.rb /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/active_record/connection_adapters/mysql2_adapter.rb /var/lib/gems/1.8/gems/activerecord-3.2.8/lib/active_record/connection_adapters/mysql2_adapter.rb /var/lib/gems/1.8/cache/mysql2-0.3.11.gem /var/lib/gems/1.8/cache/activerecord-mysql2-adapter-0.0.3.gem /var/lib/gems/1.8/specifications/activerecord-mysql2-adapter-0.0.3.gemspec /var/lib/gems/1.8/specifications/mysql2-0.3.11.gemspec Contents of /usr/share/redmine/Gemfile: source 'http://rubygems.org' gem 'rails', '3.2.8' gem "jquery-rails", "~> 2.0.2" gem "i18n", "~> 0.6.0" gem "coderay", "~> 1.0.6" gem "fastercsv", "~> 1.5.0", :platforms => [:mri_18, :mingw_18, :jruby] gem "builder", "3.0.0" # Optional gem for LDAP authentication group :ldap do gem "net-ldap", "~> 0.3.1" end # Optional gem for OpenID authentication group :openid do gem "ruby-openid", "~> 2.1.4", :require => "openid" gem "rack-openid" end # Optional gem for exporting the gantt to a PNG file, not supported with jruby platforms :mri, :mingw do group :rmagick do # RMagick 2 supports ruby 1.9 # RMagick 1 would be fine for ruby 1.8 but Bundler does not support # different requirements for the same gem on different platforms gem "rmagick", ">= 2.0.0" end end # Database gems platforms :mri, :mingw do group :postgresql do gem "pg", ">= 0.11.0" end group :sqlite do gem "sqlite3" end end platforms :mri_18, :mingw_18 do group :mysql do gem "mysql" end end platforms :mri_19, :mingw_19 do group :mysql do gem "mysql2", "~> 0.3.11" end end platforms :jruby do gem "jruby-openssl" group :mysql do gem "activerecord-jdbcmysql-adapter" end group :postgresql do gem "activerecord-jdbcpostgresql-adapter" end group :sqlite do gem "activerecord-jdbcsqlite3-adapter" end end group :development do gem "rdoc", ">= 2.4.2" gem "yard" end group :test do gem "shoulda", "~> 2.11" # Shoulda does not work nice on Ruby 1.9.3 and seems to need test-unit explicitely. gem "test-unit", :platforms => [:mri_19] gem "mocha", "0.12.3" end local_gemfile = File.join(File.dirname(__FILE__), "Gemfile.local") if File.exists?(local_gemfile) puts "Loading Gemfile.local ..." if $DEBUG # `ruby -d` or `bundle -v` instance_eval File.read(local_gemfile) end # Load plugins' Gemfiles Dir.glob File.expand_path("../plugins/*/Gemfile", __FILE__) do |file| puts "Loading #{file} ..." if $DEBUG # `ruby -d` or `bundle -v` instance_eval File.read(file) end Contents of /usr/share/redmine/Gemfile.lock: GEM remote: http://rubygems.org/ specs: actionmailer (3.2.8) actionpack (= 3.2.8) mail (~> 2.4.4) actionpack (3.2.8) activemodel (= 3.2.8) activesupport (= 3.2.8) builder (~> 3.0.0) erubis (~> 2.7.0) journey (~> 1.0.4) rack (~> 1.4.0) rack-cache (~> 1.2) rack-test (~> 0.6.1) sprockets (~> 2.1.3) activemodel (3.2.8) activesupport (= 3.2.8) builder (~> 3.0.0) activerecord (3.2.8) activemodel (= 3.2.8) activesupport (= 3.2.8) arel (~> 3.0.2) tzinfo (~> 0.3.29) activeresource (3.2.8) activemodel (= 3.2.8) activesupport (= 3.2.8) activesupport (3.2.8) i18n (~> 0.6) multi_json (~> 1.0) arel (3.0.2) builder (3.0.0) coderay (1.0.8) erubis (2.7.0) fastercsv (1.5.5) hike (1.2.1) i18n (0.6.1) journey (1.0.4) jquery-rails (2.0.3) railties (>= 3.1.0, < 5.0) thor (~> 0.14) json (1.7.5) mail (2.4.4) i18n (>= 0.4.0) mime-types (~> 1.16) treetop (~> 1.4.8) metaclass (0.0.1) mime-types (1.19) mocha (0.12.3) metaclass (~> 0.0.1) multi_json (1.3.7) mysql (2.8.1) mysql2 (0.3.11) net-ldap (0.3.1) pg (0.14.1) polyglot (0.3.3) rack (1.4.1) rack-cache (1.2) rack (>= 0.4) rack-openid (1.3.1) rack (>= 1.1.0) ruby-openid (>= 2.1.8) rack-ssl (1.3.2) rack rack-test (0.6.2) rack (>= 1.0) rails (3.2.8) actionmailer (= 3.2.8) actionpack (= 3.2.8) activerecord (= 3.2.8) activeresource (= 3.2.8) activesupport (= 3.2.8) bundler (~> 1.0) railties (= 3.2.8) railties (3.2.8) actionpack (= 3.2.8) activesupport (= 3.2.8) rack-ssl (~> 1.3.2) rake (>= 0.8.7) rdoc (~> 3.4) thor (>= 0.14.6, < 2.0) rake (10.0.0) rdoc (3.12) json (~> 1.4) rmagick (2.13.1) ruby-openid (2.1.8) shoulda (2.11.3) sprockets (2.1.3) hike (~> 1.2) rack (~> 1.0) tilt (~> 1.1, != 1.3.0) sqlite3 (1.3.6) test-unit (2.5.2) thor (0.16.0) tilt (1.3.3) treetop (1.4.12) polyglot polyglot (>= 0.3.1) tzinfo (0.3.35) yard (0.8.3) PLATFORMS ruby DEPENDENCIES activerecord-jdbcmysql-adapter activerecord-jdbcpostgresql-adapter activerecord-jdbcsqlite3-adapter builder (= 3.0.0) coderay (~> 1.0.6) fastercsv (~> 1.5.0) i18n (~> 0.6.0) jquery-rails (~> 2.0.2) jruby-openssl mocha (= 0.12.3) mysql mysql2 (~> 0.3.11) net-ldap (~> 0.3.1) pg (>= 0.11.0) rack-openid rails (= 3.2.8) rdoc (>= 2.4.2) rmagick (>= 2.0.0) ruby-openid (~> 2.1.4) shoulda (~> 2.11) sqlite3 test-unit yard Results of gem list: actionmailer (3.2.9, 3.2.8) actionpack (3.2.9, 3.2.8) activemodel (3.2.9, 3.2.8) activerecord (3.2.9, 3.2.8) activerecord-mysql2-adapter (0.0.3) activeresource (3.2.9, 3.2.8) activesupport (3.2.9, 3.2.8) arel (3.0.2) builder (3.0.0) bundler (1.2.1) coderay (1.0.8) erubis (2.7.0) fastercsv (1.5.5) hike (1.2.1) i18n (0.6.1) journey (1.0.4) jquery-rails (2.0.3) json (1.7.5) mail (2.4.4) metaclass (0.0.1) mime-types (1.19) mocha (0.12.3) multi_json (1.3.7) mysql (2.8.1) mysql2 (0.3.11) net-ldap (0.3.1) pg (0.14.1) polyglot (0.3.3) rack (1.4.1) rack-cache (1.2) rack-openid (1.3.1) rack-ssl (1.3.2) rack-test (0.6.2) rails (3.2.9, 3.2.8) railties (3.2.9, 3.2.8) rake (10.0.0) rdoc (3.12) rmagick (2.13.1) ruby-openid (2.1.8) shoulda (2.11.3) sprockets (2.2.1, 2.1.3) sqlite3 (1.3.6) thor (0.16.0) tilt (1.3.3) treetop (1.4.12) tzinfo (0.3.35) yard (0.8.3) Results of 'bundle show`: Gems included by the bundle: * actionmailer (3.2.8) * actionpack (3.2.8) * activemodel (3.2.8) * activerecord (3.2.8) * activeresource (3.2.8) * activesupport (3.2.8) * arel (3.0.2) * builder (3.0.0) * bundler (1.2.1) * coderay (1.0.8) * erubis (2.7.0) * fastercsv (1.5.5) * hike (1.2.1) * i18n (0.6.1) * journey (1.0.4) * jquery-rails (2.0.3) * json (1.7.5) * mail (2.4.4) * metaclass (0.0.1) * mime-types (1.19) * mocha (0.12.3) * multi_json (1.3.7) * mysql (2.8.1) * net-ldap (0.3.1) * pg (0.14.1) * polyglot (0.3.3) * rack (1.4.1) * rack-cache (1.2) * rack-openid (1.3.1) * rack-ssl (1.3.2) * rack-test (0.6.2) * rails (3.2.8) * railties (3.2.8) * rake (10.0.0) * rdoc (3.12) * rmagick (2.13.1) * ruby-openid (2.1.8) * shoulda (2.11.3) * sprockets (2.1.3) * sqlite3 (1.3.6) * thor (0.16.0) * tilt (1.3.3) * treetop (1.4.12) * tzinfo (0.3.35) * yard (0.8.3)

  Read the article

• Extract archive here, autodetect subfolder

  - by lorancou

  I use 7-Zip under Windows 7 to extract all kind of archives. The ever-running problem is that there is not a single way to handle subfolders. Some people create their archives like this (let's call it type A): . +-- subfolder ¦   +-- file 1 ¦   +-- file 2 ¦   +-- ... "Extract Here" will extract everything to subfolder/, which is fine; "Extract to <Folder>" will create an extra subfolder level, which is annoying. And other people create them like that (let's call it type B): . +-- file1 +-- file 2 +-- ... "Extract Here" will populate the current folder, which can bring a lot of mess if this folder already contains tons of other files, and which is very annoying; "Extract to <Folder>" will create a subfolder and conveniently stuff it with the archive content, which is fine. So this leaves two options: always choose to "Extract to <Folder>" and live with the extra subfolder for type A archives. Or open the archive before extracting it to check if this is a type A or B, and then appropriately select "Extract Here" or "Extract to <Folder>". I usually do the latter, but I just discovered that KDE is offering a very handy Extract Archive Here, Autodetect Subfolder feature that automates that. It'll "Extract Here" if there's only one subfolder in the archive, otherwise it'll "Extract to <Folder>". I love this idea. Is there a Windows 7 tool offering this option? Preferably integrated in the explorer context menu? Maybe it's hidden somewhere in 7-Zip and I just didn't find it?

  Read the article

• What could cause these "failed to authenticate" logs other than failed login attempts (OSX)?

  - by Tom

  I've found this in the Console logs: 10/03/10 3:53:58 PM SecurityAgent[156] User info context values set for tom 10/03/10 3:53:58 PM authorizationhost[154] Failed to authenticate user (tDirStatus: -14090). 10/03/10 3:54:00 PM SecurityAgent[156] User info context values set for tom 10/03/10 3:54:00 PM authorizationhost[154] Failed to authenticate user (tDirStatus: -14090). 10/03/10 3:54:03 PM SecurityAgent[156] User info context values set for tom 10/03/10 3:54:03 PM authorizationhost[154] Failed to authenticate user (tDirStatus: -14090). There are about 11 of these "failed to authenticate" messages logged in quick succession. It looks to me like someone is sitting there trying to guess the password. However, when I tried to replicate this I get the same log messages except that this extra message appears after five attempts: 13/03/10 1:18:48 PM DirectoryService[11] Failed Authentication return is being delayed due to over five recent auth failures for username: tom. I don't want to accuse someone of trying to break into an account without being sure that they were actually trying to break in. My question is this: is it almost definitely someone guessing a password, or could the 11 "failed to authenticate" messages be caused by something else?

  Read the article

• Single Sign On for intranet with Apache and Linux MIT Kerberos

  - by Beerdude26

  Greetings, I am looking for a way to do a single sign on to an intranet in the following manner: A Linux user logs on via a graphical frontend (for example, GNOME). He automatically requests a TGT for his username from the MIT Kerberos KDC. Via some way or another, the Apache server (which we'll assume is on the same server as the KDC), is informed that this user has logged in. When the user accesses the intranet, he is automatically granted access to his web applications. I don't think I've seen this kind of functionality while searching the net. I know the following possibilities exist: Using an authentication module such as mod_auth_kerb, a user is presented with a login prompt to enter his username and password, which are then authenticated against the MIT Kerberos server. (I would like this to be automatic.) IIS supports integrated Windows logon via ASP.Net when the user is part of an Active Directory. (I'm looking for the Linux / Apache equivalent.) Any suggestions, criticism and ideas are highly appreciated. This is for a school project to show a proof-of-concept, so every handy piece of information is more than welcome. :)

  Read the article

• SYS-5016T-MTFB will not POST without manual assistance (Motherboard: X8STi-F)

  - by Dan

  I have a Supermicro 5016T-MTFB 1U server which I am in the process of setting up, but it has a really strange problem. When the system is powered on it will not POST until I press the reset button a few times, followed by pressing the delete key on the keyboard to "wake it up". If I power it on and do nothing, the fans spin up but nothing else happens at all. After pressing the reset button once, the red "overheat" light comes on and blinks which is supposed to indicate a fan failure - but all the fans are working. Pressing reset again usually stops the blinking, and the system starts the normal POST routine but it will not actually get to the bios screen unless I press delete. If I don't press delete, it just continues to hang. After pressing delete it will take me into the bios setup screen, if I exit without saving changes I can boot the system normally. I was able to successfully install Linux with no trouble...but upon rebooting the same problem happened again. This board has integrated IPMI which I thought was the problem, so I disabled it via the jumper on the board. Did not help. Each time this system powers on, it goes on for a second, then turns off again for another second, then turns back on again. I don't know why it does that. Here is what I put in the system: 1 x Xeon E5630 (Nehalem) 80W TDP (it's not overheating, CPU temps stay under 40 degrees C) 2 x Kingston 2GB x 3 DDR3-1066 Memory ECC, unbuffered, unregistered (kvr1066d3e7sk3/6g) 1 x Intel X25-M 160 GB 2 x Western Digital RE3 1TB

  Read the article

• Problem with network policy rule in Network Policy Server

  - by Robert Moir

  Trying to configure RADIUS for a college network, and have run into the following frustration: I can't set an "AND" condition for group membership of authenticated objects in the network policy rules, e.g. I'm trying to create a NPS rule that says, essentially "IF user is a member of [list of user groups] And is authenticating from a computer in [wireless computer group] then allow access. The screenshot above is the rule I am having trouble with. It does not work as written. The rule underneath it, which is identical in every aspect except the conditions rule, does work. I've tried changing the non-working rule to define each set of groups as "Windows group" rather than specifically as machine and user groups, with no change. With the "faulty" rule enabled and the working one disabled, any attempt to login with a valid account from a machine that is in the wireless computers group gives a 6273 audit event in the windows event log: Reason code 66 - "the user attempted to use an authentication method that is not enabled on the matching network policy". Disabling the "faulty" rule, enabling the other rule and logging in with the same account and computer works just fine.

  Read the article

• SSH login very slow on OS X Leopard

  - by acjohnson55

  My SSH sessions take a very long time to initiate. This applies for logins with and without passwords, interactive and non-interactive. I have tried setting 'GSSAPIAuthentication no' and 'IPQoS 0x00' on the client side, and 'UseDNS no' on the server side, but no dice. I'm really stumped and frustrated. The worst part is that it SFTP takes forever to establish connections too, making file transfer much longer than it would be otherwise. I thought the problem might be something with PAM, because of where the hang is in the sshd log below, so I tried commenting out each line one-by-one in the /etc/pam.d/sshd file. Some caused login to be impossible, some had no apparent effect. I can't really tell if PAM is stalling for other services, but I can say that su'ing into my account from another account with 'su -l' has no apparent delay. I tried creating a new user account, just to see if there was something wrong with my existing account, and the same problem persisted. Any ideas of what's going on? On the client side, the most verbose mode outputs (redacted where reasonable): OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data ... debug1: ... line 1: Applying options for ... debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 53: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to ... [x.x.x.x] port 22. debug1: Connection established. debug1: identity file /.../.ssh/id_rsa type -1 debug1: identity file /.../.ssh/id_rsa-cert type -1 debug3: Incorrect RSA1 identifier debug3: Could not load "/.../.ssh/id_dsa" as a RSA1 public key debug1: identity file /.../.ssh/id_dsa type 2 debug1: identity file /.../.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.2 debug1: match: OpenSSH_5.2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug2: fd 3 setting O_NONBLOCK debug3: load_hostkeys: loading entries for host "..." from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],ssh-rsa debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],ssh-rsa,[email protected],[email protected],ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 136/256 debug2: bits set: 523/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ... debug3: load_hostkeys: loading entries for host "..." from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug3: load_hostkeys: loading entries for host "x.x.x.x" from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug1: Host '...' is known and matches the RSA host key. debug1: Found key in /.../.ssh/known_hosts:9 debug2: bits set: 492/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /.../.ssh/id_dsa (0x7f8b7b41d6c0) debug2: key: /.../.ssh/id_rsa (0x0) debug1: Authentications that can continue: publickey,password,keyboard-interactive debug3: start over, passed a different list publickey,password,keyboard-interactive debug3: preferred publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering DSA public key: /.../.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-dss blen 434 debug2: input_userauth_pk_ok: fp ... debug3: sign_and_send_pubkey: DSA ... debug1: Authentication succeeded (publickey). Authenticated to ... ([x.x.x.x]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. ****** Hangs here ****** debug2: callback start debug2: client_session2_setup: id 0 debug2: fd 3 setting TCP_NODELAY debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env TERM_PROGRAM debug3: Ignored env SHELL debug3: Ignored env TERM debug3: Ignored env TMPDIR debug3: Ignored env Apple_PubSub_Socket_Render debug3: Ignored env TERM_PROGRAM_VERSION debug3: Ignored env TERM_SESSION_ID debug3: Ignored env USER debug3: Ignored env COMMAND_MODE debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env Apple_Ubiquity_Message debug3: Ignored env __CF_USER_TEXT_ENCODING debug3: Ignored env PATH debug3: Ignored env MKL_NUM_THREADS debug3: Ignored env PWD debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env DYLD_LIBRARY_PATH debug3: Ignored env PYTHONPATH debug3: Ignored env LOGNAME debug3: Ignored env DISPLAY debug3: Ignored env SECURITYSESSIONID debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 On the server side, the debug output looks like: Sep 16 18:46:40 ... sshd[31435]: debug1: inetd sockets after dupping: 3, 4 Sep 16 18:46:40 ... sshd[31435]: Connection from x.x.x.x port 52758 Sep 16 18:46:40 ... sshd[31435]: debug1: Current Session ID is 56AC0FB0 / Session Attributes are 00008000 Sep 16 18:46:40 ... sshd[31435]: debug1: Running in inetd mode in a non-root session... assuming inetd created the session for us. Sep 16 18:46:40 ... sshd[31435]: debug1: Client protocol version 2.0; client software version OpenSSH_5.9 Sep 16 18:46:40 ... sshd[31435]: debug1: match: OpenSSH_5.9 pat OpenSSH* Sep 16 18:46:40 ... sshd[31435]: debug1: Enabling compatibility mode for protocol 2.0 Sep 16 18:46:40 ... sshd[31435]: debug1: Local version string SSH-2.0-OpenSSH_5.2 Sep 16 18:46:40 ... sshd[31435]: debug1: Checking with Service ACLs for ssh login restrictions Sep 16 18:46:40 ... sshd[31435]: debug1: call to mbr_user_name_to_uuid with <...> suceeded to retrieve user_uuid Sep 16 18:46:40 ... sshd[31435]: debug1: Call to mbr_check_service_membership failed with status <0> Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: initializing for "..." Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: setting PAM_RHOST to "x.x.x.x" Sep 16 18:46:40 ... sshd[31435]: Failed none for ... from x.x.x.x port 52758 ssh2 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys2 Sep 16 18:46:40 ... sshd[31435]: debug1: fd 5 clearing O_NONBLOCK Sep 16 18:46:40 ... sshd[31435]: debug1: matching key found: file /.../.ssh/authorized_keys2, line 1 Sep 16 18:46:40 ... sshd[31435]: Found matching DSA key: ... Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys2 Sep 16 18:46:40 ... sshd[31435]: debug1: fd 5 clearing O_NONBLOCK Sep 16 18:46:40 ... sshd[31435]: debug1: matching key found: file /.../.ssh/authorized_keys2, line 1 Sep 16 18:46:40 ... sshd[31435]: Found matching DSA key: ... Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: ssh_dss_verify: signature correct Sep 16 18:46:40 ... sshd[31435]: debug1: do_pam_account: called Sep 16 18:46:40 ... sshd[31435]: Accepted publickey for ... from x.x.x.x port 52758 ssh2 Sep 16 18:46:40 ... sshd[31435]: debug1: monitor_child_preauth: ... has been authenticated by privileged process Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: establishing credentials ***** Hangs here ***** Sep 16 18:46:54 ... sshd[31435]: User child is on pid 31654 Sep 16 18:46:54 ... sshd[31654]: debug1: PAM: establishing credentials Sep 16 18:46:54 ... sshd[31654]: debug1: permanently_set_uid: 509/20 Sep 16 18:46:54 ... sshd[31654]: debug1: Entering interactive session for SSH2. Sep 16 18:46:54 ... sshd[31654]: debug1: server_init_dispatch_20 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_open: ctype session rchan 0 win 1048576 max 16384 Sep 16 18:46:54 ... sshd[31654]: debug1: input_session_request Sep 16 18:46:54 ... sshd[31654]: debug1: channel 0: new [server-session] Sep 16 18:46:54 ... sshd[31654]: debug1: session_new: session 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_open: channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_open: session 0: link with channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_open: confirm session Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_global_request: rtype [email protected] want_reply 0 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request pty-req reply 1 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req pty-req Sep 16 18:46:54 ... sshd[31654]: debug1: Allocating pty. Sep 16 18:46:54 ... sshd[31435]: debug1: session_new: session 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_pty_req: session 0 alloc /dev/ttys008 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request env reply 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req env Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request shell reply 1 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req shell Sep 16 18:46:54 ... sshd[31655]: debug1: Setting controlling tty using TIOCSCTTY.

  Read the article

• VSFTPD 530 Login incorrect

  - by sc.

  I'm trying to get a vsftpd server set up on CentOS 5.3 x64. I'm not able to get any local user login's to work. Here is my vsftpd.conf: local_enable=YES write_enable=YES pam_service_name=vsftpd connect_from_port_20=YES listen=YES pam_service_name=vsftpd xferlog_std_format=NO log_ftp_protocol=YES chroot_local_user=YES Here is the output of vsftp.log: Mon Sep 13 23:34:44 2010 [pid 19243] CONNECT: Client "10.0.1.138" Mon Sep 13 23:34:44 2010 [pid 19243] FTP response: Client "10.0.1.138", "220 (vsFTPd 2.0.5)" Mon Sep 13 23:34:44 2010 [pid 19243] FTP command: Client "10.0.1.138", "USER dwelch" Mon Sep 13 23:34:44 2010 [pid 19243] [dwelch] FTP response: Client "10.0.1.138", "331 Please specify the password." Mon Sep 13 23:34:44 2010 [pid 19243] [dwelch] FTP command: Client "10.0.1.138", "PASS <password>" Mon Sep 13 23:34:44 2010 [pid 19242] [dwelch] FAIL LOGIN: Client "10.0.1.138" Mon Sep 13 23:34:45 2010 [pid 19243] [dwelch] FTP response: Client "10.0.1.138", "530 Login incorrect." And the output of the secure log: Sep 13 17:40:50 intra vsftpd: pam_unix(vsftpd:auth): authentication failure; logname= uid=0 euid=0 tty=ftp ruser=dwelch rhost=10.0.1.138 user=dwelch It looks like pam is not authenticating the user. Here is my /etc/pam.d/vsftp file: #%PAM-1.0 session optional pam_keyinit.so force revoke auth required pam_listfile.so item=user sense=deny file=/etc/vsftpd/ftpusers onerr=succeed auth required pam_shells.so auth include system-auth account include system-auth session include system-auth session required pam_loginuid.so Can anyone see what I'm missing? Thanks.

  Read the article

• SSL setup: UCC or wildcard certificates?

  - by quanza

  I've scoured the web for a clear and concise answer to my SSL question, but to no avail. So here goes: I have a web-service requiring SSL support for authentication pages. The root-level domain does not have the "www" - i.e., secure://domain.com - but localized pages use "language-code.domain.com", i.e. secure://ja.domain.com So I need at least a wildcard SSL certificate that supports secure://*.domain.com However, we also have a public sandbox environment at sandbox.domain.com, which we also need to support under localized domains - so secure://ja.sandbox.domain.com needs to also work. The previous admin managed to purchase a wildcard SSL certificate for .domain.com, but with a Subject Alternative Name for "domain.com". So, I'm thinking of trying to get a wildcard certificate with SANs defined as "domain.com" and ".*.domain.com". But now I'm getting confused because there seem to be separate SAN certificates, also called UCC certificates. Can someone clarify whether it's possible to get a wildcard certificate with additional SAN fields, and ultimately what the best way is to support: secure://domain.com secure://.domain.com secure://.*.domain.com with the fewest (and cheapest!) number of SSL certificates? Thanks!

  Read the article

• Automounting Active Directory home drives on a Linux server on login

  - by Ethan

  I've got a Centos 5.7 box authenticating against Active Directory through PBIS Open (the new LikeWise Open), which works well. Now, I'm trying to get the server to automount the user's AD home directory, located at //ad.server.dom/shares/home directories (Yeah, it's a space in the path. I didn't set this up). Each user has a directory in there with the same name as the user. I've tried to get pam_mount working, but it has a series of issues on RedHat and friends, and I can't seem to get that working. The directory does need to be automounted for the server to perform it's role. My reading on automount seems to suggest that there's no way to get it to do it's thing with authentication, though I'm happy to be proved wrong. I've looked at this resource, but it requires version RedHat (thus CentOS) 6 or higher, and newer packages than I have. I can manually (As root) mount the AD directory using the command mount.cifs "//ad.server.dom/Shares/home directories/testuser" /home/local/AD/testuser/nfs_mount/ -o username=testuser and when I log in as testuser, I can see all of the sample files in the nfs_share directory. Any tips towards the right direction would be highly appreciated. This is going to be on a server at a college, so it needs to be fairly stable, and would lead towards more Linux adoption there.

  Read the article

• How to get a higher resolution on Ubuntu 11.04 using an intel chipset

  - by Saif Bechan

  I have a bit slow PC here, so I decided to put Ubuntu 11.04 on it. It use to run Windows Vista on a resolution of 1280x1024, so both my hardware and monitor support it. Now I'm on Ubuntu, but can only run 1024x768, and the screen is not that bright. Its like when you don't have the right drivers on a Windows machine. Now i'm new to linux, so I do not know what do do. I have an onboard Intel chipset i965. Maybe this is some useful information, I read something about it on a forum: lspci 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) Can someone please tell me how I can get the screen better? saif@sodium:~$ xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9

  Read the article

• How do I get a Wireless N PCi card to connect to a wireless G router?

  - by Andy

  I'm having some problems setting up a new wireless PCI card on a WinXP SP3 PC. I know that the router is configured correctly. It is a Linksys WRT54GL, using 802.11b/g. Security mode is WPA2 Personal with TKIP+AES encryption. I am able to connect to this fine using my laptop (first gen MacBook with a 802.11b built in card). The new PCI card is also Linksys, but it supports 802.11n. Card seems to be installed ok (Windows sees it fine, doesn't list any errors in Device Manager), however when it scans for available wireless networks it can't find my wireless network (the router is set to broadcast the SSID). I tried to enter the network SSID manually, but that didn't seem to help. I chose WPA2-PSK for network authentication. The only options for encryption are TKIP or AES - I've tried both, neither worked. I am sure that I typed in my wireless key correctly. At this point, I don't think the problem is with encryption, but something else. It almost seems like I need to switch the wireless card into g mode, but I haven't found a way to do that (if that is even possible/necessary - I thought n was fully backwards compatible with g). Also, the PC is in the same room as the router, and my laptop, so I don't think that it is an interference issue. Any ideas what I'm doing wrong? I'm running out of things to try at this point. :(

  Read the article

• How to re-join an AD2003 domain with Samba after deleting the machine account?

  - by Guss

  During some troubleshooting I deleted the machine account for a Linux server running samba from our AD 2003 domain. We are using Kerberos for authentication, and after I deleted the machine account I tried to join the domain again using net ads join -U Administrator But I keep getting Kerberos errors like these: [2009/08/18 16:14:36, 0] libads/kerberos.c:ads_kinit_password(228) kerberos_kinit_password [email protected] failed: Client not found in Kerberos database Failed to join domain: Improperly formed account name It appears as if samba remembers that it once had an account with the AD and keeps trying to reconnect to it, but I want to create a new account from scratch. I tried to delete all the .tdb files I could find as well as everything under /var/cache/samba but to no avail - it still behaves the same. I also tried to create the machine account on the AD side, but then I get a similar error when I try to join, about failure to authenticate with the machine account - it looks like samba tries the previous machine account password and I don't know how to reset it, or even if I could figure out what samba uses - how to set it in the AD. Any help would be greatly appreciated, as at this point the only thing I can think about is to reformat and reinstall the machine, and I would really REALLY love to not do that. Thanks in advance.

  Read the article

• Encryption setup for Linux NAS?

  - by Daniel

  There's a bazillion hard disk encryption HOWTOs, but somehow I can't find one that actually does what I want. Which is: I have a home NAS running Ubuntu, which is being accessed by a Linux and a Win XP client. (Hopefully MacOS X soon...) I want to setup encryption for home dirs on the NAS so that: It does not interfere with the boot process (since the NAS it tucked away in a cupboard), the home dirs should be accessible as a regular file system on the client(s) (e.g. via SMB), it is easy to use by 'normal' people, (so it does not require SSH-ing to the NAS, mount the encrypted partition on command line, then connecting via SMB, and finally umount the partition after being done. I can't explain that to my mom, or in fact to anyone.) does not store the encryption key the NAS itself, encrypts file meta-data and content (i.e. safe against the 'RIAA' attack, where an intruder should not be able to identify which songs are in your MP3 collection). What I hoped to do was use Samba + PAM. The idea was that on connecting to the SMB server, I'd have to enter the password on the client, which sends it to the server for authentication, which would use the password to mount the encrpytion partition, and would unmount it again when the session was closed. Turns out that doesn't really work, because SMB does not transmit the password in the plain and hence I can't configure PAM to use the incoming password to mount the encrypted patition. So... anything I'm overlooking? Is there any way in which I can use the password entered on the client (e.g. on SMB connect) to initiate mounting the encrypted dir on the server?

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• IPSec for LAN traffic: Basic considerations?

  - by chris_l

  This is a follow-up to my Encrypting absolutely everything... question. Important: This is not about the more usual IPSec setup, where you want to encrypt traffic between two LANs. My basic goal is to encrypt all traffic within a small company's LAN. One solution could be IPSec. I have just started to learn about IPSec, and before I decide on using it and dive in more deeply, I'd like to get an overview of how this could look like. Is there good cross-platform support? It must work on Linux, MacOS X and Windows clients, Linux servers, and it shouldn't require expensive network hardware. Can I enable IPSec for an entire machine (so there can be no other traffic incoming/outgoing), or for a network interface, or is it determined by firewall settings for individual ports/...? Can I easily ban non-IPSec IP packets? And also "Mallory's evil" IPSec traffic that is signed by some key, but not ours? My ideal conception is to make it impossible to have any such IP traffic on the LAN. For LAN-internal traffic: I would choose "ESP with authentication (no AH)", AES-256, in "Transport mode". Is this a reasonable decision? For LAN-Internet traffic: How would it work with the internet gateway? Would I use "Tunnel mode" to create an IPSec tunnel from each machine to the gateway? Or could I also use "Transport mode" to the gateway? The reason I ask is, that the gateway would have to be able to decrypt packages coming from the LAN, so it will need the keys to do that. Is that possible, if the destination address isn't the gateway's address? Or would I have to use a proxy in this case? Is there anything else I should consider? I really just need a quick overview of these things, not very detailed instructions.

  Read the article

< Previous Page | 275 276 277 278 279 280 281 282 283 284 285 286  | Next Page >