Search Results

Search found 1467 results on 59 pages for 'disabling'.

Page 28/59 | < Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >

• 4 - 7 second delay accessing Mysql across the network

  - by Kristiaan

  Hello, our company has recently purchased a new server with the intention of replacing our aging database server. its a full 64bit 2008 enterprise system, i have got the basic server setup and configured and then installed the 64bit version of mysql on the server, this has then been configured to match where possible our existing server as much as it can. however i have noticed that when it was swapped with the production database server our software systems had an increased delay accessing the mysql database this was anything beween 4 - 7 seconds. i have tried disabling TOE, IPv6 and a few other suggested soultions to this but so far cannot find out where this slowdown is coming from. replacing the server with the production one and the delay goes away. in terms of software and hardware the servers are not very identical at all due to one being windows 2003 std with a 32bit server and the new one being windows 2008 enterprise with a 64bit server. thanks Kris

  Read the article

• Wireless DHCP doesn't work until wired Ethernet plugged in

  - by MT_Head

  A client of mine has an Asus R1F tablet running Windows XP Tablet SP3. It has an Intel 3945ABG wireless card; wired Ethernet is a Realtek something-or-other. In the past few days, it's developed an odd problem: WiFi authenticates, but can't get an address via DHCP. plug in wired Ethernet - both interfaces get good addresses unplug cable, WiFi continues to work until shutdown. Next morning, repeat process. I've tried: turning WiFi off/on (there's a slider switch) disabling/re-enabling via Device Mangler uninstalling and reinstalling the driver for the 3945ABG... changing from Intel Pro/SET to Windows Wireless Zero Config (and back) restarting the router changing the static DHCP assignments at the router upgrading the router firmware, just on general principles The router/access point is pfSense 1.2.3RC1 (was 1.2.2); wireless card is Atheros-based. None of the 12 other users (5 with tablets) are having problems.

  Read the article

• Windows 8 Unable to perform hibernate

  - by Jones

  Windows 8 Enterprise edition x86. Already enabled hibernate option, to have it on shutdown menu (start menu?) and set to hibernate on lid closing. However it's not hibernating for me. When I'm trying to sleep, it's sleep fine and wake up like a kid. But when I'm demanding hibernate, it disconnects internet, turn off screen and be back to lock screen in one second. Steps I've tried. Complete shutdown Clear hiberfile.sys by disabling and enabling back Resetting my power settings. Causes I suspect: Had dual boot with BackTrack with Windows 8 GUI boot manager. It was fine until I reinstall BackTrack, bootmgr resetted and I'm in Ubuntu boot menu;. Using additional hard disk through USB cable.(But it's not a problem before few days, however) How to make my system to hibernate and wakeup again.

  Read the article

• Disable IPv6 on Loopback address (Localhost, Computer name, ...)

  - by Greg Bray

  We tried installing a 3rd party software product on a new Windows 2008 R2 server and found that everything works except for accessing local services through loopback addresses such as localhost or the computer name (ex: VPS-Web which resolves to localhost). We are not using IPv6 and would like to disable it until the software is compatible. I tried using these instructions for disabling IPv6 on Windows 2008 R2 but it did not disable the protocol for localhost. Pinging localhost or VPS-Web will still return ::1: instead of 127.0.0.1. I can use ping localhost -4 to get the correct address, but IPv6 takes precedent over IPv4 so the 3rd party software only gets the IPv6 address.

  Read the article

• Uninstall or Disable Dell Wave

  - by Onion-Knight

  The image we put on our company laptops includes the Dell Wave interface for Biometric log in. The Wave UI increases boot time by about 5 minutes (because it loads the fingerprint database(a feature I don't use)), so I'm trying to uninstall it, but with little success. There is no line-item in the Add/Remove Programs menu to formally delete it, nor is there a Service I can stop/remove to disable the Wave UI. I've tried looking online, but all I find instead are hits for Google Wave and virus-removal forums with HyjackThis dumps that include Dell Wave records. Any ideas? Edit: Removal isn't entirely necessary. Disabling the Wave UI is good enough.

  Read the article

• Remote Desktop fails with no error

  - by Duane

  Recently, I've been having problems connecting to a remote machine via RDP. I can connect fine exactly once, but all subsequent attempts fail until the remote machine is rebooted. I seem to authenticate properly, but the RDP logon dialog disappears after showing, "Configuring remote session..." for a few seconds. No errors or other useful info is written either to my screen or the Event Logs of the two machines involved. I've tried disabling remote sound as others have suggested, with no success. I'm still investigating a solution, but would appreciate any thoughts. Fortunately, I can reboot the box remotely w/o causing any problems, but this is a less than ideal workaround.

  Read the article

• Dell Latitude E4300 TouchPad - Odd Behavior

  - by Cade Roux

  I'm seeing some intermittent behavior on the touchpad. First it wasn't working at all. Then during restart, for a little while it seemed like the buttons attached to the joystick and external mouse were both swapped left/right. Then I went in to the dell touchpad control and disabled the touchpad and re-enabled it and nothing happened. Then a short while after disabling the joystick the touch pad started working. So I restarted to see if it would keep the settings and before login, the touchpad appeared to work, then after login it stopped working for a few minutes while login continued. Then after the login was almost completed it started to work again. It appeared to have retained the settings for the disabled joystick. It seems like perhaps there are conflicting mouse drivers trying to simultaneously or similar. This doesn't seem normal for the touchpad to be disabled for so long after login. What steps should I take to ensure the drivers are right?

  Read the article

• Disable static content caching in IIS 7

  - by Lee Richardson

  I'm a developer having what should be a relatively simple problem in IIS 7 on Windows Server 2008 R2. The problem is that IIS 7 is overzealously caching all static content on the server. It's caching all .html and .js content and not noticing when the content changes on disk unless I iisreset. I've tried the following: Deleting the local cache in my browser (I'm 99% positive this is a server caching issue) In IIS Admin in OutputCaching adding an .html extension and unchecking "User mode caching" and unchecking "Kernel-mode caching" In IIS Admin in OutputCaching adding an .html extension and checking "User mode caching" and selecting the radio for "Prevent all caching" In IIS Admin editing Output Cache Feature settings and unchecking "Enable cache" and "Enable kernel cache under OutputCaching. Running "C:\Windows\System32\inetsrv\config\appcmd set config "SharePoint - 80" -section: system.webServer/caching -enabled:false" Looking through applicationHost.config and disabling anything related to caching I could find. Nothing seems to work. I'm getting very frustrated. Can anyone please help?

  Read the article

• Group policy to disable notifications of particular errors?

  - by resolver101

  How do i disable the notifications of particular errors? A little background to my issue. During the installation of the Kaspersky, it disables all the windows firewall for all except the domain. I have remedied this by creating an offline policy in Kaspersky which enables the Kaspersky firewall when out of the office (ie not connected to the office network). The problem now is that users in the office now see a notification showing that the firewall is disabled even though it’s enabled in all scenarios. It’s just that work and home show as disabled when the clients are connected to the office LAN. I’ve looked into the notifications and you can disable the notification (not recommended) but I don’t want to do this incase other relevant messages are stopped from being displayed. http://blogs.technet.com/b/networking/archive/2010/12/16/disabling-firewall-alerts-in-the-action-center.aspx

  Read the article

• How to configure auto-logon in Active Directory

  - by Jonas Stensved

  I need to improve our account management (using Active Directory) for a customer support site with 50+ computers. The default "AD"-way is to give each user their own account. This adds up with a lot of administration with adding/disabling/enabling user accounts. To avoid this supervisors have started to use shared "general" accounts like domain\callcenter2 etc and I don't like the idea of everyone knowing and sharing accounts and passwords. Our ideal solution would be to create a group with computers which requires no login by the user. I.e. the users just have to start the computer. Should I configure auto-logon with a single user account like domain\agentAccount? Is there anything else to consider if I use the same account for all users? How do I configure the actual auto-logon with a GPO on the group? Is there a "Microsoft way" without 3rd party plugins? Or is there a better solution?

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results. I also tried all the suggestions from this question Why doesn't Windows 7 wake up from sleep?. Still no results.

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state [closed]

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results.

  Read the article

• Dell Latitude E4300 TouchPad - Odd Behavior

  - by Cade Roux

  I'm seeing some intermittent behavior on the touchpad. First it wasn't working at all. Then during restart, for a little while it seemed like the buttons attached to the joystick and external mouse were both swapped left/right. Then I went in to the dell touchpad control and disabled the touchpad and re-enabled it and nothing happened. Then a short while after disabling the joystick the touch pad started working. So I restarted to see if it would keep the settings and before login, the touchpad appeared to work, then after login it stopped working for a few minutes while login continued. Then after the login was almost completed it started to work again. It appeared to have retained the settings for the disabled joystick. It seems like perhaps there are conflicting mouse drivers trying to simultaneously or similar. This doesn't seem normal for the touchpad to be disabled for so long after login. What steps should I take to ensure the drivers are right?

  Read the article

• Prevent Windows 7 from installing a "critical" updates that crashes the system

  - by Sylverdrag

  I am running Windows 7 home premium. Up until yesterday, everything was going just beautifully, until I received a "critical update". As soon as the critical update was installed, the system became extremely unstable and froze up every few minutes requiring me to restart the system several times, with the same results. I used system restore to roll back the * update, and everything went back to normal... except that I keep getting a message telling me to restart the computer so that it can install this "critical update". There is no "don't install that crap on my machine" option. Disabling the updates doesn't change anything, turning off the windows update service doesn't change anything either, and being on Home premium, I have no access to the group policies. Any ideas of what can be done to prevent Windows from installing this update the next time I reboot?

  Read the article

• Cisco IOS router config -- how to disable SSH / SNMP on all but loopback address?

  - by chris

  Sorry for the naive question; a quick reading of the cisco docs doesn't answer this question... So I've got a router (say for the sake of argument a 4500 running IOS 15.x) It has interfaces in 3 different subnets -- 10.0.0.1/24, 10.0.1.1/24, and 10.0.2.1/24 It also has a loopback address of 172.16.0.33 How do I make it so that SSH / SNMP and other administrative traffic works on the 172 address but doesn't work on the IP addresses I wish to only use for L3 forwarding? Ideally this can be done by disabling the control plane access to these interfaces not just by using an ACL, but whatever, I don't actually care that much as long as it works... Thanks!

  Read the article

• How to force Windows 7 to ask for a "fresh" IP address from DHCP server?

  - by haimg

  I'm troubleshooting a certain issue with my DHCP configuration, and need my Windows machine to ask for a "fresh" IP address, so I can see which address DHCP server gives by default. When I do ipconfig /release followed by ipconfig /renew, Windows "proposes" its old IP address to the DHCP server (just checked with Wireshark, initial "DHCP Discover" message has Option-50 (requested IP address) with Windows machine's old IP). Tried disabling/enabling network adapter. Same behavior. Question: How can I force Windows to just ask for a new IP address, without proposing its old IP address.

  Read the article

• Postfix/dovecot remove LDAP user

  - by dove221

  I have to remove or blacklist an LDAP/dovecot user. The authentication is setup from active directory what I cannot manage so I thought there should be a way at least to disable this specific user on the mailserver locally. # Virtual Accoutns - LDAP - MS AD virtual_mailbox_maps = ldap:/etc/postfix/ldap_mailbox_maps.cf virtual_alias_maps = ldap:/etc/postfix/ldap_alias_maps_redirect_true.cf ldap:/etc/postfix/ldap_alias_maps_redirect_false.cf ldap:/etc/postfix/ldap_mailbox _groups.cf virtual_mailbox_domains = domain.com virtual_uid_maps = static:1000 virtual_gid_maps = static:1000 virtual_transport = dovecot dovecot_destination_recipient_limit = 1 Anybody knows how to do it? I followed this guide for disabling 1 user through postfixes access file: http://www.cyberciti.biz/faq/howto-blacklist-reject-sender-email-address/ Unfortunately it doesn't work. It's like the settings stored in LDAP are overruling the access rule. Instead of postfix rejecting the mail it keeps accepting it. Thanks!

  Read the article

• System Restore Points

  - by Ross Lordon

  Currently I am investigating how to schedule an automatic initiation of a system restore point for all of the workstations in my office. It seems that Task Scheduler already has some nice defaults (screenshots below). Even the history for this task verifies that it is running successfully. However, when I go to Recovery in the Control Panel it only lists the System Restore Points one for every previous for only 3 weeks back even if I check the show more restore points box. Why don't the additional ones appear? Would there be a better way to implement a solution, like via group policy or a script? Is there any documentation on this online? I've been having a hard time tracking anything down except how to subvert group policy disabling this feature.

  Read the article

• How to troubleshoot memory card read?

  - by shinjin

  The built in memory card reader in my laptop mounts SD cards as read-only only. This happens both in Windows 7 and Ubuntu. Most of the time. Ever now an then it works. After a some non-deterministic combination of uninstalling/reinstalling/disabling/enabling of the driver with the mandatory reboots the card reader works for a while. Is there any sane way to troubleshoot if it's an actual hardware problem, or just a matter of drivers? I've tested it with several SD cards, that work just fine in other devices. System: Acer Aspire 8951G, Windows 7-64bit

  Read the article

• Cannot connect to telnet server

  - by BloodPhilia

  So, I can't use telnet to connect to any server but it works fine from a different computer. It just says it can't connect. I tried the following things: Disable firewall and AV protection. (Basically, there was no security feature left online) Telnet is set to "Trusted" in my AV protection. (Kaspersky Internet Security 2011) Using Putty to telnet, but apparently Putty's connection is also inhibited. (Says it can't connect to host) Disabling the telnet client in Control Panel and then re-enabling it. (Windows 7 Ultimate) hosts file is clean. Checked for nasties using MBAM and KIS 2011 as well as going though my HijackThis logs, nothing found. I can connect to the same machines/servers through the web browser, ping, tracert, etc. Only telnet seems to be blocked. Any other thoughts?

  Read the article

• Can I disable Pam Loginuid? Can I find out options used to configure kernel?

  - by dunxd

  I am getting a lot of the following types of error in my secure log on a CentOS 5.4 server: crond[10445]: pam_loginuid(crond:session): set_loginuid failed opening loginuid sshd[10473]: pam_loginuid(sshd:session): set_loginuid failed opening loginuid I've seen discussion of this being caused when using a non-standard kernel without the correct CONFIG_AUDIT and CONFIG_AUDITSYSCALL options set. Where this is the case, it is advised to comment out some lines in the pam.d config files. I am running a Virtual Private Server where I need to use the kernel provided by the supplier. Is there a way to find out what options they used to configure the kernel? I want to verify if the above is the cause. If this turns out not to be the cause, what are the risk of disabling pam_loginuid for crond and sshd?

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

• diagnostic software for wifi adapter

  - by Nathan Fellman

  I'm having trouble with my wifi connection. Is there any software out there that can help me determine if the problem is in the drivers or in the hardware? Regretfully, I'm working on Vista Edit: The problem I'm having is that the Vista reports that the wireless radio is connected, shows an IP and all, the router also shows that the computer is connected, but there's no connectivity. I can't logon to the router, and I can't even ping it. When I ping it I get the response: General Failure I have tried connecting with and without various wireless security protocols. I have tried disabling the wireless adapter and re-enabling it from the Device Manager I have tried updating the driver None of this has helped. When I connect via Ethernet (with a cable, that is), everything works fine. Edit: I'm not using any firewall on the computer, that I'm aware of. The IP address for the WIFI adapter is similar to the one for the LAN adapter. They differ by one.

  Read the article

• NGINX downloads text file instead of displaying it

  - by Hoang Lam

  I have Nginx installed with the following nginx.conf: user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /vagrant/access.log main; sendfile on; keepalive_timeout 65; include /etc/nginx/conf.d/*.conf; } Everytime I tried the URL of any text files (not PHP, it works fine), the browser asks to download it. Common measure such as disabling default-type octet/stream fails.

  Read the article

• Configuring NVIDIA Quadro with Dell Precision M4600

  - by vsecades

  After a frustrating couple of weeks when I recently bought my Dell Precision laptop, I managed to fix an issue where Ubuntu (yes, was NOT using Windows, get serious) would not recognize the video card and would cause all sorts of problems all over the place. I ended up one Saturday morning nearly throwing this thing away, when I managed to find a post about NVIDIA Optimus technology... ( http://www.pcmag.com/article2/0,2817,2358963,00.asp ). Now I am a huge advocate of disruptive new stuff, as long as we keep the broader audience in mind. Anyhow, disabling this (which as the BIOS settings state only work on Windows 7 or later), effectively allow the NVIDIA based Ubuntu driver to kick in full force. No need for a trash can anymore thankfully. As I saw multiple posts all over the place about this, check your BIOS, disable and try the video again to see if this corrects your issues. Best of luck!

  Read the article

< Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >