Search Results

Search found 8410 results on 337 pages for 'hardware reserved'.

Page 282/337 | < Previous Page | 278 279 280 281 282 283 284 285 286 287 288 289  | Next Page >

• exFAT to NTFS formatting troubles

  - by user1083734

  I recently ran a chkdsk on 2.5" 230GB SATA HDD but the plug was pulled before the end of the chkdsk and since then it wouldn't boot up. Deciding to scrap all data on the HDD (no longer needed it), I then fitted it into an external HDD caddy and (in diskpart) cleaned the disk, created new partition and volume and tried to format it to NTFS. It couldn't do this on long or short formats and so I went with the less-appreciated alternative - exFAT (I run Win7). It quick formats to exFAT fine but encounters errors during long format. At the moment it is exFAT. Of course I would really like it to be NTFS as I will probably need to use it on Win XP too. Could anyone suggest a method of trying to reformat to NTFS? Do you think that, when chkdsk was interrupted first time, the disk was corrupted and is irretrievable? I find this situation slightly odd, as it HAS formatted to exFAT and DOES seem to work when I copy files across! Also, I CAN use disk management console to create several partitions: e.g. a 50GB partition and then a large 180GB partition. The 50GB and WILL long-format to NTFS but the 180GB will not! I'm thinking hardware fault, but then I notice that it WILL format to exfAT! Much confusion!

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• What is the latest on Microsoft Expressoin Studio licensing?

  - by DanM

  In the past, there's been an issue with Microsoft not allowing you to deactivate an Expression Studio key. Basically, you get two keys per license. If you assign both keys (say one to a desktop and one to a laptop), then you upgrade to a new machine (say you replace your laptop or upgrade some of the hardware), you have to buy a new copy of Expression Studio ($600 for Ultimate). This seems ludicrous to me, and I'm wondering if anyone knows if this policy is still in place. I can't seem to find a EULA online anywhere, so I don't know where to find this information. I know my laptop is due for replacement soon, and I want to know if I'm going to have to sink $600 into a software product I already purchased. For background, please refer to this thread on the Microsoft Expression forums: http://social.expression.microsoft.com/Forums/en-US/general/thread/da5587bc-b098-4c6a-9a56-af3608d940d0 Note that this thread is locked. Microsoft doesn't seem to want people to discuss this. This is one reason I'm posting here rather than on that site.

  Read the article

• ESXi Guests will not boot on IBM x3550 M3

  - by Adrian

  I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. VM Host Server: IBM x3550 M3 7944AC1 server w/ 2x Intel Xeon E5607 2.27Ghz CPUs ESXi 5.0.0 Build 623860, built for IBM Hardware downloaded from IBM Storage: 2x500GB SAS local storage 8GB RAM Vt is verified to be ENABLED Server Health Status: Normal The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspucious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space.

  Read the article

• I/O Error on LG GSA-H12N DVD drive on Windows 7

  - by Ashwin

  I am facing an I/O Error when I try to burn DVD data discs on my LG GSA-H12N DVD drive on Windows 7. Note that I was able to do this same operation on the same hardware/software just a day earlier without any problems, but with Windows XP. The only change (AFAIK) has been the installation of Windows 7 to replace Windows XP on this PC. Here is the error I get when I try to burn a DVD data disc using CDBurnerXP 4.2.7.1801: Burning error occured An error occured while burning the disc. Most likely the disc is not usable. Usually these errors happen if the inserted media is not compatible to the drive or of poor quality. (devNTSPTI_IO_Error) Could not write to Disc (LBA: 52864 Length: 32). SCSI Pass-through Interface I/O Error. - 0xFF045D Note that there can be no problem with the discs since I have been using the same discs (from the same box) just before the Windows 7 installation with no problems. The only change has been Windows 7. I tried InfraRecorder v0.5 and ImgBurn v2.5 and got similar I/O errors: Note that Windows 7 lists the LG GSA-H21N drive as being compatible (see this link). I also checked the LG Drivers website and using the firware update from there updated the drive firmware from version UL01 to UL02. But, even this has not helped. The drive reads DVDs without any problem, but continues to produce coasters. Could someone help me figure out what is the problem? Thanks :)

  Read the article

• Adobe premiere CS5 problem with the display driver

  - by user30179

  This error is really hindering our project. I get an error, it started showing-up June 16th 2010. There are no windows updates at the on the same date as the error, other than (Windows Defender) Seems to happen when working with Image overlays. ERROR: "The NVIDIA OpenGL driver detected a problem with the display driver and is unable to continue. The application must close." We opened the side of the case in the possibility there is an over heating problem. Nvidia Driver ver 8.16.11.9175 (nVidia Quadro FX 1700) I am running: Windows 7 x64 Adobe premiere CS5 Production nVidia Quadro FX 1700 (MRGA14L) 4 Gig ram RAID 10 2 750GB drives Duo core 3.0 6MB L2 Cache This is at least three other people that have come across this error: NVidia Forum EVGA Forum NVidia Forum UPDATE: Having the case open did not help. I also installed New Nvidia drivers now I get a different error: *ERROR:*Your hardware configuration does not meet minimum specifications needed to run the application. The application must close. I ran Windows Update and installed all four updates so now I am waiting to see if the error occurs again. Anything beyond this I am out of options.

  Read the article

• Performance associated with storing millions of files on NTFS

  - by Tim Brigham

  Does anyone have a method / formula, etc that I could use - hopefully based on both current and projected numbers of files - to project the 'right' length of the split and the number of nested folders? Please note that although similar it isn't quite the same as Storing a million images in the filesystem. I'm looking for a way to help make the theories outlined more generic. Assumptions I have 'some' initial number of files. This number would be arbitrary but large. Say 500k to 10m+. I have considered the underlying physical hardware disk IO requirements that would be necessary to support such an endeavor. Put another way As time progresses this store will grow. I want to have the best balance of current performance and as my needs increase. Say I double or triple my storage. I need to be able to address both current needs and projected future growth. I need to both plan ahead and not sacrifice too much of current performance. What I've come up with I'm already thinking about using a hash split every so many characters to split things out across multiple directories and keeping the trees even, very similar as outlined in the comments in the question above. It also avoids duplicate files, which would be critical over time. I'm sure that the initial folder structure would be different based on what I've outlined, and depending on the initial scale. As far as I can figure there isn't a one size fits all solution here. It would be horrendously time intensive to work something out experimentally.

  Read the article

• Convert a cassette tape recording to digital format

  - by Electric Automation

  Has anyone been successful with transferring audio cassette tape recordings to a digital format? I would like to preserve old cassette tape recordings of my grandparents to some digital format: MP3, WAV, etc... The quality of the tapes are mediocre. I think I can handle the quality restoration but getting the audio from tape to digital is my question. Below is a list of the hardware that I can work with: Cassette Deck: I have a Technics stereo cassette deck model RS-B12. It has separate left and right IN and OUT RCA type jacks on the back. In the front it has a headphone phono jack, plus left and right mic input phono jacks. On the computer side: -I have a Windows Vista PC with no additional software other than what came with the machine from Costco. No sound editing software that I can see. There is no sound card on the PC. On the front panel there is a mini-phono mic input jack and there are several different types of in/out mini-phono jacks on the back. In addition, USB and Firewire. I also have access to a new (2009) iMac with a mini-phono input jack for a powered mic or other audio source and GarageBand that has come with the computer. In addition, USB and Firewire. What are my options for getting these cassette recordings into a digital format? Whats the best format? What sort of wires would I need and will I want to utilize the USB or Firewire or can I simply use the audio inputs on the PC (or Mac) to receive the audio stream?

  Read the article

• Windows 7 fails to install

  - by Brian Ortiz

  I'm upgrading from Vista SP1 (which was actually upgraded from XP over a year ago) to Windows 7 RTM (64-bit Ultimate to 64-bit Ultimate). After 4 hours or so, the install fails with the message "This version of Windows could not be installed, Your previous version of Windows has been restored, and you can continue to use it." This error is back at my Vista desktop, there's no error that I could see during install, I just a message indicating that it was reverting everything. I tracked down the error logs and here's the log at I uploaded the error log (from C:\$WINDOWS.~BT\Sources\Panther) and uploaded onto Pastebin. Here is an excerpt: 2009-08-09 02:54:57, Error Number of Enumerated Devices = 21[gle=0x00000103] 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x[gle=0x80092004] 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x[gle=0x80092004] It was suggested that I upgrade to SP2 before upgrading to Vista, but this made no difference. I since uninstalled SP2 since it was creating some problems with a piece of hardware. I know a fresh install is best, but I'm hoping to avoid that because I'd need a new hard drive. Per Reuben's instruction, I found the install's dump and uploaded it here. (266 KB)

  Read the article

• How to recover a Linksys WRT54GL router that has a blinking green power LED and no response from the

  - by Peter Mounce

  I was flashing the router with the Tomato firmware, but something went wrong; I'm not sure what. Now, the router responds to ping at 192.168.1.1 (my Mac's on a static IP 192.168.1.21), but the web-interface doesn't come up. I have read that this situation is recoverable in a [couple of places][2], but I haven't been having much success and so I wondered whether anyone could help. From my Mac (OSX 10.5) I have tried to tftp a new vanilla-Linksys firmware to the router and reboot; according to the trace, this sends it but the router behaves no differently after a reboot. I've read that if boot_wait is turned on, I'll have an easier time, but I haven't been able to find any instructions that tell me how I can tell whether I did this or not (I don't think I have, but I might have, when I tinkered the first time months ago - the router has worked since then, though). I have found a couple of references to [something called JTAG][3], which seems like some kind of [homebrew diagnostic cable thing][4], but that's a little beyond my ken. Happy to try it, with muppet-level instructions, though (I do software, not hardware!). So, I'm at a bit of a loss, really, and wondered whether anyone could provide me with the route (ha. ha.) out of this mess? Hm, I can't post all the links I wanted to until I have some more reputation.

  Read the article

• Very slow browsing shared folder XP client/host

  - by Ickster

  I have a pretty straightforward setup where I'm storing media files on an XP pro machine, and sharing the folder to be accessed by other XP pro machines around the house. (Typically, there's only one client accessing the share at a time, although there may be several with the share mounted.) It's been working just fine for years, but I've recently started having some problems. A couple of days ago, the host PC had power disconnected while it was running. It was restarted and everything seemed fine initially, but since then browsing the shared folder from client machines has been extremely slow and actually reading data is all but impossible. The problem exists in every access method I've tried: Windows Explorer, VLC dialogs, command line, etc. My first thought was that the disk was experiencing problems, but there are no problems viewing the files locally on the host machine. My second thought was that there was a network problem on the host machine, so I removed and reinstalled drivers for the NIC with no change. My third thought was that there might've been a problem elsewhere on the network, so I swapped out hardware to no avail. I'm regrouping and trying to come up with a methodical approach to figuring out what might be wrong. I would of course be thrilled if you can suggest specific problems (Microsoft KB articles, etc.) that I might check, but I'm not expecting a silver bullet. If you can help me outline an approach to identify the problem (including recommended tools, e.g., disk checkers, network analyzers, etc.) I'd greatly appreciate it.

  Read the article

• 3 Servers, is this is a cluster?

  - by Andy Barlow

  Hello, At the moment I have one Ubuntu server, 9.10, running with a simple Samba share, a mail server, DNS server and DHCP server. Mostly its just there for file sharing and email server. I also have 2 other servers that are exactly the same hardware and spec as the first, which have an rsync set up to retrieve the shared folders and backs them up. However, if the first server goes down, all of our shares disappear along with our mail and the system must be rebuilt. Also I tend to find if people are downloading a large amount from the file server, no-one can access there emails - especially in the morning when everyone is signing in at once. Would it be more beneficial for me to have all 3 servers, all running the same services, doing the same thing with some sort of cluster with load balancing? I'm not really sure where to begin looking, or how to go about such a setup where 3 servers are all identical, but perhaps one acts as the main load balancer?? If someone can point me in the right direction, or if this simply sounds like one of those Enterprise Cloud's that is now a default setup in Ubuntu Server 9.10+, then I'll go down that route. Cheers in advance. Andy

  Read the article

• How can I fix video tearing and pausing on Windows XP Flash videos?

  - by xvs

  I have what should be a reasonably fast PC: it's a Quadcore Intel 6600 at 2.4 GHz, 4MB of RAM, an ATI 3800 series video card and an LG L246WP monitor, which I selected particularly because it was supposed to work well with video and have no trails or other artifacts. So I should be able to play video with no problems. And I can, as long as that video isn't Flash video. With Flash, what I see is tearing, especially during pans, and pausing -- every few seconds the video pauses for about 300ms while the sound stays continuous. I tried going into the video card setup and changing vertical sync, pulldown detection, windows media video acceleration, deinterlacing and triple buffering. but no combination of settings I've tried has changed or corrected the problem in any way. I've also tried enabling and disabling hardware acceleration in the Flash settings, to no avail. This problem happens whether or not the video is streaming or has fully streamed in before playing. So, what can I do? Is this just a flash issue or is there a way to get it to work?

  Read the article

• How to run the CPU at something like 75%?

  - by Tobias Kienzler

  My notebook is too old for me to invest into a new fan (it will simply be replaced by a new one when the final heat death occurs), but when it runs on full speed I feel like sitting in front of a vacuum cleaner with integrated cooking... I'm currently using NHC, the Max Battery mode of which let's the CPU run at 50% (~800 MHz). That's fine for most applications, and both temperature and noise remain low. However, on some occasions I need a bit more speed, more around 75% maybe. Can I set the power saving settings somehow so that the CPU won't surpass 75% of it's capability so that an acceptable compromise between power and noise is achieved? I can't set the CPU frequency in the BIOS and since on rare occasions I'd like to be able to switch to 100% without much hassling, hardware solutions like setting jumpers are no option. This answer to a similar (linux!) question mentions NHC should be able to offer these options, but for me they are all greyed out: The notebook is an Asus Z9200K, I guess NHC doesn't support its chipset enough for these advanced options.

  Read the article

• Help with memory usage issues on VPS

  - by Niall Collins

  Hi there, I am running a VPS server with 6 .net web sites/applications running on it. I am having issues with performance on the server, mainly it running out of memory. I contacted the company that lease the server to me and they told me it was because I also had sql server 2008 express also running on the server. So I went ahead and removed this, uninstalled etc. However I still seem to be having issues. For example at present, looking at resource consumption, the virtual memory is: ID: vprvmem Current Use: 894,328,832 bytes Limit: 1,073,741,824 bytes This means useage of ~80%. Is there any way I can check out exactly that applications, web sites, software is taking up most of the servers memory, so I can look at rectifying it. I feel that 80% is much to high to allow for contingency for a spike in traffic. I have got extra memory resources added to the box recently, but I would prefer finding the source of the problem rather than throwing extra memory at it. Maybe these levels are correct and alls running ok, but would like to investigate it to make sure. My knowledge of hardware is limited as I mostly deal in the spectrum of software. So any tools out there that can help me or any pertient advice.

  Read the article

• CUPS causes printer to click and doesn't print

  - by Pez Cuckow

  I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

  Read the article

• Programmer configuring a new network

  - by David Lively

  I'm in the process of expanding my home network from a couple of laptops on a wireless Verizon FiOS router to include: Linksys 24-port switch Cisco Pix 515 Cisco 3640 router One new development desktop and three new machines to act as a db server, web server and a backup system. My company is moving offices and we've decommissioned some older hardware, which I was able to pick up for the cost of the labor to move it home from the office. The benefits to working with dedicated web and db servers are very valuable to me. I know very little about network topology, other than that everything plugs into the switch, which then plugs into the cheap Verizon router. (Verizon provides a coax connection that the router must translate into Ethernet before I can use it with any of this equipment). Questions: What is the recommended topology for this equipment? Verizon router - Pix - 3600 - switch? Is the 3600 even necessary or desirable? The Verizon router has one WAN port and 4 client ports, all 10/100. Is there any performance benefit at all to wiring multiple connections from the verizon router to the switch, assuming I don't use the Pix? Should I use the Pix? Software firewalls are a pain, and seem silly if I have a device like this lying around. Anything else I should know? Am I wasting my time with this? I also obtained a 7 foot rack, shelves, patch panels, UPS, patch panels, etc, which are going into a conveniently air conditioned closet. All constructive advice appreciated.

  Read the article

• Pure Terminal Server 2003 system hangs

  - by Donovan

  System Profile: IBM Server hardware Windows Ent Server 2003 running terminal services. No Citrix. Max user load: 30 Symptoms: While in the course of normal operation our terminal server will hang up. As far as I can tell there isn't any trigger that's plainly visible yet. The way in witch it hangs may give a clue though. The hang presents its self by users not being able to initiate any new processes. All processes currently loaded into memory work just fine. Example: outlook 2007. You may continue to read email, operate the client and such. Some people don't even realize the hang has occurred for a bit of time. My attempts to troubleshoot have been futile. Reacting to the hang does no good because I can't start any new processes to investigate. After I reboot the server my next instinct would be to begin logging to catch the hang occurring but I'm not sure what to log. Right now I'm attempting to keep process explorer running in case the issue occurs again. Sometimes it happens twice a day, other times, once a week. Anyone have any ideas on how I could set myself up for better success in tracking this problem down? Thanks, Donovan

  Read the article

• Get Illegal Instruction error when booting Linux in VirtualBox, works fine when booted directly

  - by rkjnsn

  I have a computer on which I am dual booting Windows 7 and Gentoo Linux (both 64-bit). I want to be able to load up my Linux installation in a VM while I am booted into Windows. I have installed VirtualBox and followed the instructions for creating a raw disk VMDK. When I start the VM, Linux starts booting, but then fails with the following error when unlocking my root partition: truecrypt[441] trap invalid opcode ip:373615538e0 sp:3dd0e0dfb60 error:0 in libpixman-1.so.0[373614d6000+8d000] Everything works fine when I boot into Linux directly. What could cause an illegal instruction to be hit in libpixman only when booting in VirtualBox? Update: As a troubleshooting step, I recompiled pixman without "-march", and no longer get an illegal instruction error in that library. (The boot fails in the same spot with the same error in a different library, however.) How can I determine the specific opcode that isn't working in VirtualBox so I can disable it in my CFLAGS without having to disable all CPU-specific optimizations? I am still confused as to why there would be any user-mode instruction that would fail to work in a VM. Is this a known limitation? My CPU is an Intel Core i7 3720QM, and I have hardware virtualization support enabled.

  Read the article

• CDROM does not appear on desktop, MACOS 10.5.7

  - by Cheeso

  When I pop a CDROM into the drive of my Macbook Pro, It spins up, I hear it, but no icon appears on the desktop. (I think it's 10.5.7; actually not sure how to verify this on Mac, but I think I saw a 10.5.7 flash by somewhere). In the finder preferences, I have "Show these items on the Desktop" set to show HDs, External Disks, and CDs, DVDs, and ipods. All three of those are checked. I do see the internal HD on the desktop. In Disk utility I can see the CD/DVD hardware. It says "MATSHITA DVD-R UJ-857E...". From Disk Utility I can eject the drive. But in Finder, there is never a CD/DVD listed under "Devices". When I insert a disk, nothing happens, I cannot see it. I also cannot boot from bootable CDROMs by holding C down . Suggestions? I am not very experienced with Mac; I have used Windows for years. EDIT Two updates: I saw this article on support.apple.com, and modified the hostconfig appropriately. It did not have the AUTODISKMOUNT entry, so I added one, rebooted. Same behavior. It does not see the CDROM in Finder, does not mount it on desktop. I put an old manufactured CDROM into the drive, and voila! it showed up on the desktop. The CD that does not appear is a GNome Partition Editor Live CD, which I guess is based on debian. That CD boots in other (non-Mac) PCs. I want to use this to adjust the Bootcamp partition. Suggestions?

  Read the article

• Different network response for indentical co-located machines

  - by Santosh

  We have a situation as follows: We have a two different virtual machines (VMs) on some remote server farm. The machines are identical in terms of hardware/software(OS) configurations. We have a J2EE application running on JBoss on each of those two machines. These two applications are of different version sav V1 on VM1 and V2 on VM2. We observed some degraded response time for application V2 when accessed via public URL. When we accessed the application through a secured VPN, there is hardly any difference. The bandwidth test (upload/download speed, ping etc) shows that VM1 is responding better when accessed via secured VPN. We concluded that the application does not seem to have performance issue. Because, it that's the case the performance degradation should also be there when access via VPN. So we concluded its the network problem. But since those two identical VMs are on same network we are looking for the reasons for different responses. My question is, given the above situation, what could be reasons for such a behavior ?

  Read the article

• How to debug a kernel created using ubuntu-vm-builder?

  - by user265592

  Aim: Trying to perform a code walkthrough of what functions are getting called for sending and receiving packets over the network. I am building a kernel and using gdb for debugging/ tracing purposes. I have build a vm using the following command : time sudo ubuntu-vm-builder qemu precise --arch 'amd64' --mem '1024' --rootsize '4096' --swapsize '1024' --kernel-flavour 'generic' --hostname 'ubuntu' --components 'main' --name 'Bob' --user 'ubuntu' --pass 'ubuntu' --bridge 'br0' --libvirt 'qemu:///system' And I can run the VM successfully in qemu using the following command: qemu-system-x86_64 -smp 1 -drive file=tmpGgEOzK.qcow2 "$@" -net nic -net user -serial stdio -redir tcp:2222::22 Now, I want to debug the kernel using gdb. For this I need an executable with debug symbols(vmlinux), which apparently I don't have, as the vm-builder never asked for any such options and simply created a .qcow2 file. Question 1: Am I taking the correct approach to solve the problem and is there an easier way to do it? Question 2: Is there a way to debug this kernel using GDB? P.S: I don't have hardware support for KVM. Please correct me if I am wrong. Thanks.

  Read the article

• The Server Fault Wiki of recommended practices [migrated]

  - by Avery Payne

  So I've noticed that there are several recommendations on basic practices on Server Fault, but there doesn't seem to be a cohesive view as to how those recommendations would all fit together. So I thought I would lump these together as a kind of mental exercise to see what the "ServerFault Community IT Department" would look like if it were implemented. This would give a few things: it would make a reasonable wiki (in the true wiki spirit of many contributions), it would provide several links to well-vetted practices, and it would be kind of fun to see what the amalgamation would look like. And who knows, it may even point out some interesting issues between different forms of "best practices", although I would be stunned if there was a conflict hidden in there someplace... Add your favorites from Server Fault as answers, and I'll re-edit this section with the results. Here's a few catagories to collect different ideas together. Hardware Configuration(s) Server room configuration. Server room temperature Firmware Updates and Scheduling Storage Configuration(s) Selecting a NAS box Linux: Dealing with /tmp Linux: Install apps in /var or /opt? Network Configuration(s) checking DNS health and compliance Security Practice(s) Password (General) Best Practices Password sharing methods Windows Update Updating Windows Servers that are hosts for VMs Network Service(s) User Service(s) User Naming & Deletion Upgrade Process(es) Disaster Recovery Checking Backups Documenting an outage for a post-mortem review Last Edit: 2010-02-17

  Read the article

• Windows 2008 64bit: applications and explorer always hang

  - by Phil Farthing

  I setup a couple of Window 2008 64bit systems about 5 months ago. Initially all seemed well. Now however, for no apparent reason, things are dog slow, apps hang, explorer hangs, just clicking on something can cause a CPU spike of 100%, and often it's explorer that is eating it up. As I have two on identical hardware, and they experience the same problem, it doesn't seem related to addon software. The only thing these have in common is Kaspersky and I've tried disabling/uninstalling to no avail. There are no useful error messages in the event logs. Actually, the system never even reports app hangs. Sometimes, it similar to what I've seen on Windows 7 systems where the screen goes milky and asks if I want to trouble shoot, that's only when get impatient and click happy. The really odd thing, is that it will NOT do this for a few minutes at a time, and then starts up again. Like I will click on the start menu and browse for the Admin Tools, the start menu will hang at some point and I'll have to wait about a minute, then it's OK. The next time I do this, a few seconds later, it's fine. Every click seems to hang the first time around, then be ok the second time if I do the exact same thing. If anyone has any suggestions, please PLEASE let me know! thanks =)

  Read the article

• Reducing video mode switching during Linux boot

  - by Zack

  When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

  Read the article

< Previous Page | 278 279 280 281 282 283 284 285 286 287 288 289  | Next Page >