Search Results

Search found 8185 results on 328 pages for 'capture card'.

Page 287/328 | < Previous Page | 283 284 285 286 287 288 289 290 291 292 293 294  | Next Page >

• Updating ASUS BIOS on Windows 7 64bit

  - by joesavage

  I've recently decided that I want to try and utilize my two graphics cards so that I can have a dual monitor setup. Unfortunately Windows only seems to notice my most recent graphics card installation - and so I've been told that I should look into my BIOS and try to enable two graphics cards. I could not find this setting anywhere in my M2N68-AM Plus v0210 BIOS. After some further research I figured that I should perhaps upgrade my BIOS, so I searched and managed to download the latest version (v1804) as a ROM file. However I am having difficulty figuring out how to install it. I've tried using the Asus EZFlash feature built into my BIOS, but when trying to load up a variety of different ROMs that are for my motherboard/BIOS I get the error: Boot block in file is not valid! I'm not totally sure what I should do to fix this, so I'm looking into other methods of upgrading my BIOS - however I can't really find any solutions that seem to work. Asus Update is for 32-bit only, AFUDOS doesn't appear to work on my Windows 7 64-bit system (I think it's supposed to run in DOS or something - but that just sounds confusing since I know nothing about DOS). Could anybody help me with this?

  Read the article

• Replaced CPU and black screen but no beep?

  - by luke

  I'm having a bit of trouble with a GIGABYTE GA-MA78G-DS3H (rev. 2.0) motherboard. Recently when trying to clean my AMD Phenom II X 4 CPU, I dropped it and broke some pins. I have now brought a Athlon 64 X2 5400+. However, it does not seem to work. To begin with, I cleared the CMOS via the jumper located near the battery. This was because I had my AMD Phenom II overclocked and did not wish for the same voltage to go to the new CPU. I then tried booting with the monitor plugged into the chipsets VGA but no luck. No signal was sent to the monitor, and the monitor just went into standby. I then tried it off the graphics card but the same happened again. Then I tried to check whether the CPU could executed some BIOS codes by stripping the RAM out and making sure a speaker was plugged in but no beeps could be heard. I replaced the speaker and tried again but no luck. The CPU is brand-new so what is going wrong?

  Read the article

• IP Masquerade and forwarding

  - by poelinca

  Hi all , i got a dedicated server running ubuntu server 10.10 with 3 ip adresses on the same eth card ( example: eth0 192.168.0.1 , eth0:0 188.78.45.0 , eth0:1 ... ) with a 3 virtual machines running ( virtualization technologi used is lxc but i don't think this matters too much ) . Now i need to redirect all ports opened ( using ufw to close/open ports ) from the ip 188.78.54.0 ( eth0:0 ) to a virtual machine ip ( let's say for example 192.168.2.3 ) , all requests made by a virtual machine should be redirected back to the virtual machine that made the request ( in this example 192.168.2.3 ) . Lets say the second vm has the ip 192.168.2.4 now i need to redirect all opened ports to from eth0:1 to this ip and viceversa . And so on and so on , what are the iptables/ufw rules to get this done ? and where to save them ( witch config file ) so they stay the same after reboot . In a few words redirect all requests comming from/to eth0:0 to a certan ip , all requests comming from/to eth0:1 to another ip ... Remember i'm saying all ports opened becouse they might be dynamicly changed . p.s. please excuse my bad english

  Read the article

• What can prevent a Server 2008 machine accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. I don't think it is this because we have a 2003 Server machine behind a different hardware firewall and that one works fine. What on earth is left?!

  Read the article

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• How do I tell Windows to use 802.11 in preference to 3G?

  - by Jon Skeet

  I have a Samsung NC-10 netbook which I take to work every day. Most of the time I use it just on the train/bus, but I also use it at work and home. It has a built-in 3G card which I want to use when travelling, but I'd prefer to use wifi when I'm at work or home, for obvious reasons. Unfortunately, if the 3G connection is up, Windows appears to use that in preference to wifi. Starting up and shutting down the 3G modem is a bit of a pain - it's not hard as such, just a bit inconvenient. Ideally I'd like it to always be up, and even have the connection itself up all the time, but without routing traffic through it if there's a wifi connection up. This is what my Android phone does, for example. Is there somewhere in Windows which lets me express an ordering for network interfaces? I suspect the routing table may be relevant, but it's a bit of a pain to mess around with. I'd really expect there to be a simple GUI way of setting this up - after all, it would equally be useful when dealing with wired vs wifi connections. I'm currently using Windows XP Home, but Windows 7 answers would also be useful as I'll be migrating soon.

  Read the article

• Linux on MacBook Air

  - by enduser

  I'm thinking of getting a MacBook Air. The answers to this post will help me make my decision. My questions and my understanding of current solutions are: How difficult is it to install a Linux-based OS (like Fedora or Ubuntu)? I've heard a little about rEFIt, but am not sure what to make of it. Is it completely necessary? Do I still need it if I don't plan to dual boot with Mac OS X? Also a dual-boot isn't necessary, I'd just like to run Fedora/Ubuntu by itself, but I'm curious to know if a dual boot is simple. Does everything 'just work'? In my current laptop I need to add a wireless driver (Broadcom card). I've heard Macs use Broadcom wireless cards. Will this be an issue? How about graphics/touchpad (& multitouch)/sound? I'm aware there are tutorials out there on how to install some older version of some os on your Mac, but my questions are a bit more general: Will it be easy to use (install and configure drivers for) recent Linux distributions with a new MacBook Air? Note: I don't mind extra configuration, but would like to know where it'll be necessary, because if it's too much of a hassle I'll look at other hardware.

  Read the article

• wireless to wired internet

  - by Mark T

  My wife uses an old computer which doesn't really like having an internet connection via a USB wireless adapter. I've tried several, and none have been satisfactory. The connection gets dropped often and it is frustrating for her. A wireless card also had the same trouble. Repositioning the computer made no difference. (Two laptops, nearby, connect just fine and stay up, so it isn't the router.) However, the computer always worked well when I had an Ethernet cable connected to it. I know there is a box which will connect to my wireless network and provide an Ethernet cable connection. But the terminology used is so complex, I can't tell what it is I really need. In case that wasn't clear, here it is in different words: What I need is just the opposite of a wireless router. My wireless router takes my cable modem's Ethernet connection and makes it available to wireless clients. What I want is a box which is a wireless client to my wireless router and provides an Ethernet cable connection that I can connect to any device. I need to know the right name for a box with such capabilities. If you know of some inexpensive examples, that would also be helpful. I'm running a wireless G network with a Linksys Router.

  Read the article

• Remote offscreen rendering

  - by redmoskito

  My research lab recently added a server that has a beefy NVIDIA graphics card, which we would like to use to do scientific computations. Since it isn't a workstation, we'll have to run our jobs remotely, over an ssh connection. Most of our applications require doing opengl rendering to an offscreen buffer, then doing image analysis on the result in CUDA. My initial investigation suggests that X11 forwarding is a bad idea, because opengl rendering will occur on the client machine (or rather the X11 server--what a confusing naming convention!) and will suffer network bottlenecks when sending our massive textures. We will never need to display the output, so it seems like X11 forwarding shouldn't be necessary, but Opengl needs the $DISPLAY to be set to something valid or our applications won't run. I'm sure render farms exist that do this, but how is it accomplished? I think this is probably a simple X11 configuration issue, but I'm too unfamiliar with it to know where to start. We're running Ubuntu server 10.04, with no gdm, gnome, etc installed. However, xserver-xorg package is installed.

  Read the article

• Display errors using VMWare Player and Remote Desktop on Windows XP

  - by Tim

  I've come up against a weird display issue that I can't seem to find any "fix" for. When I first boot up my computer, everything behaves normally. If I start to use VMWare Player and/or Remote Desktop, my desktop starts having some odd video issues. The frames for some windows aren't drawn at all, if I move windows around rapidly, the area under where the window used to be isn't cleared (still shows artifacts of the content of the window), etc. In some cases, the minimize / restore / maximize buttons aren't drawn (but are click-able if you can guess where they are). I've tried the usual stuff - current drivers all around, using a single monitor, etc.. none of it seems to have any bearing. If I try to disable hardware acceleration, it tends to crash the computer. As I said earlier, it's running Windows XP, dual monitors, an NVidia en8400GS video card, asus p7p55d motherboard. Not sure what other pertinent details are needed. I would appreciate any help or suggestions!

  Read the article

• Bypass network stack. Which options do we have? Pros and cons of each option [on hold]

  - by javapowered

  I'm writing trading application. I want to bypass network stack in Linux but I don't know how this can be done. I'm looking for complete list of options with pros and cons of each of them. The only option I know - is to buy solarflare network card which supports OpenOnLoad. What other options should I consider and what is pros and cons of each of them? Well the question is pretty simple - what is the best way to bypass network stack? upd: OpenOnload It achieves performance improvements in part by performing network processing at user-level, bypassing the OS kernel entirely on the data path. Intel DDIO to allow Intel® Ethernet Controllers and adapters to talk directly with the processor cache of the Intel® Xeon® processor E5. What's key difference between these techologies? Do they do roughly the same things? I much better like Intel DDIO because it's much easy to use, but OpenOnload required a lot of installation and tuning. If good OpenOnload application is much faster than good Intel DDIO application?

  Read the article

• how is the the linux console displayed to the user and how does the user go about changing the conso

  - by Chris

  I've been searching for the last two day on trying to understand how the console displays itself to the user and how to change the console settings. I've had some luck along the way but nothing that I've found has giving me a real clear explanation of how the console is displayed or how to change or control it's display settings. Some examples that of what I'm looking for are as follows: How is the console displayed on the screen? I know with X11 it uses your graphics card driver to display graphics to the screen, but how is the consoles text mode handled? Could some one ether explain this to me or point me to an in-depth overview of it all? Is it possible to have multi-head support in console mode with separate tty's on each screen? If so how would I go about setting this up? How would you go about changing the size of the console display from the default 80x25 to a custom size? I'm testing anything I find on a debian testing build, which is just the minimal base install on a virtual box. In time I will be using this information to setup my main system which is multi-head with 3 monitors. I would like to be able to support all three displays in console mode if possible.

  Read the article

• How to install (old) packages for Ubuntu 9.04?

  - by wchrisjohnson

  Based on some excellent feedback by Mark here (http://serverfault.com/questions/285598/should-i-clone-a-physical-server-to-create-a-vm-for-a-staging-server), today I was able to use the vmware converter to clone my production server for a staging server. However the nic won't come up no matter what I do. I attempted to inistall vmware tools, as I suspect that the fact that it is not installed might prevent the nic from working. (I have the nic set as a vmxnet3 card in the vm settings). The install failed because there were several dependencies missing as well as the Linux headers. Given that Ubuntu 9.04 has been EOL'd, the packages I need to install to get the vmware tools to install are no longer available. I doubt the ubuntu 9.04 install CD has the packages on it. What are my options? I'd rather not upgrade the version of Ubuntu yet, as the point of the vm right now is to maintain parity with the production server. Might I have better luck resetting the driver to use vmxnet2 instead of the vmxnet3? Thanks in advance! Chris

  Read the article

• System With Two Network Adapters [closed]

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• No audio with streaming video

  - by Chris Barnhill

  I am having trouble with audio when playing streaming videos. My sound card is fine. I know this because if I play sounds from my local machine, there's no problem. It's only when I try to play sounds from the internet that I lose audio. This only started happening recently when I did 2 things: I connected a USB headphone/microphone set to record screencasts I began recording/publishing screencasts from screenr.com. I have tried playing video both with the headset connected and without it connected: it makes no difference. If I record a screencast on screenr.com and preview it, I hear the audio. But once I publish is and play it, there is no audio. I also hear no audio with YouTube videos. I really hope someone can help. Thanks. The latest is that the problem went away after I powered my system off and on. A reboot didn't do it, I had to actually shut down the power.

  Read the article

• Expanding raidz vdev

  - by Blubber

  I'm currently planning on installing FreeBSD 9 on my home server. The machine has 4x 1.5TB disks, and at some point, when HDD prices drop I'll be upgrading to something bigger, perhaps 3TB. The disks are connected to an IBM ServerRaid m1015 in IT mode, this card has room for up to eight disks. Now here is the problem, currently the 4x 1.5TB will be connected to the m1015. Then when prices drop I'll be adding something like 4x 3TB, also connected to the m1015. No problem yet, I can just run 2 raidz2 vdevs and put them in the same pool. But, at some point the 1.5TBs will start to break, or I will have to upgrade them when the pool runs out of space. So I started researching if it's possible to expand a raidz vdev, and I found several pages explaining the same procedure, like this on SF: How to upgrade a ZFS RAID-Z array to larger disks on OpenSolaris?. So I went a head and tried that in vmware, I installed FreeBSD 9 and created 6 virtual disks, 3 of 1GB each and 3 of 10GB each. After building a raidz vdev of the 1GBs I replaced them one by one with the 10GB, but the pool did not increase in size. Is this a limitation of the ZFS implementation in FreeBSD? Or am I just doing something wrong?

  Read the article

• DVI output _only_ working on Windows, not during booting or on Linux

  - by Mononofu

  So yesterday I booted my laptop up and the external monitor I have it connected to just stayed black. At first, I thought the problem would go away when Ubuntu was loaded, but it didn't. I tried to reboot a few times, to no avail. Then I decided to give Windows 7 a try, and suddenly (at the login-screen), my external monitor turned on and worked like normal. I have connected the monitor via DVI, and this only seems to work with Windows now. I don't even get a signal in my BIOS! Mind you, everything was working fine before that, and I didn't change a single thing. I then tried to connect the monitor via VGA (from my DVI jack, which can output VGA using an adaptor), and it worked again. However, 1920x1200 using VGA looks like crap - black print on white background is basically illegible. Do you have any ideas how to fix this peculiar problem? I only use windows for gaming, so it's no real help that it still works normally. Please also excuse any spelling mistakes, I am practically typing this blindly. Edit: I only have one graphics card in my laptop, and I can't select anything related to that in my BIOS. In fact, I can pretty much do almost nothing there. My laptop is a Nexoc Osiris E703, graphics gard is a GeForce Go 7900 GTX. As I mentioned before, DVI output during booting and on Ubuntu was working fine for years before yesterday!

  Read the article

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• Security Token for Mac/Linux/Windows, self-managed, pref. open source?

  - by DevelopersDevelopersDevelopers

  I'm looking to buy an evaluation security token (combined smart card/usb reader) for my business that works on: Windows 7 x64 OS X 10.6.x x64 Ubuntu Linux (64 or 32 bit, 10.04 or 10.10, I can bend based on possible tokens) Functionality I need is: Login authentication Authentication for whole-disk encryption (in Linux/Windows, Mac is flexible here) Signing/encryption using PGP and x.509 certificates RSA-2048 key-capable (1024 not good enough.) I can manage the certificates myself Open source middleware/drivers (not necessarily FOSS, just source available. Can flex on this, I just want to be able to audit the code. OpenSC-compatible on Linux would be great.) Is there any token that can do all of this? Or would I need multiple ones to accomplish this? Or do I need to look at smart cards and readers to get this? I have been researching this for a while and have had a heck of a time even getting accurate information about products. Also, I am in the USA, and it appears that EU export laws prevent me from buying from there, so those vendors are out. I was looking at Feitian tokens from Gooze, but since they are in France I can't buy.

  Read the article

• Power surge PC damage: How can I test all components of my PC without access to a second computer?

  - by Doug T.

  Ever since we had some crazy power surges last week my 64 bit Windows 7 PC has been acting strange. My USB network adapter disconnects from the wireless and can't detect the signal. I have to disable/reenable the adapter to detect it again. Also my wife has reported that the PC has rebooted a few times while I'm not sitting at it. Today I finally caught the reboot while I was using the PC. I got this blue screen of death. Stop Code 0x00000109: "Modification of system code or a critical data structure was detected." I followed the advice at the linked article and ran a memory test. I used memtest86 and its already found around 300,000 errors out of 8 gigs of ram. Now I'm worried -- what are the odds this is isolated to just my memory and not just a system wide problem? Isn't there a good chance that many other components are fried? More importantly, how can I test those other components? Are there tools similar to memtest I can use to test my motherboard/video card/power supply? If these are vender specific, is it typical for vendors to provide testing tools?

  Read the article

• Application Screen Repainting Issues

  - by Jeff Sheldon

  I have this issue lately at work. It drives be nuts, and I finally stopped to ask this question. It's quite often that an application I've been running just randomly fails to repaint itself for a while, usually in the editor screen. I most often see this occurring with Expression Web, Visual Studio 2008/2010 and SQL Server Management studio. These applications are what I work in the most, so I'm not surprised to mostly see it here. But I was curious if anyone else had a solution for this. I've tried: Reboots. The screen shot below is about 10 minutes after a reboot. New Video Drivers. This machine is running a Nvidia Quadro NVS 290 video card with the latest drivers. Closing other applications, this is the only thing running right now. As far as hardware, this machine has Dual Quad-Core Xeon 2.83ghz Processors, with 10 gigs of memory, running Windows XP SP3 64bit. Any help would be great. JNK EDIT: Per comments from deleted (wrong) answer: I'm running dual monitors. Set it to single display, still occurred. Rebooted, and tried it again, and it still occurred. Switched it back to dual screen. My resolution is only 1400x900 on each.

  Read the article

• iptables, forward traffic for ip not active on the host itself

  - by gucki

  I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

  Read the article

• Running computer from separate room

  - by Dan

  I want my computer to be in the basement, but to use it on the first floor. Which cables should I run through the floor? Can some be wireless or other methods? Here are some of the options I've thought of: Basic: Run DVI, usb (mouse), usb (keyboard), and audio cable (4 cables) USB Hub option: Run DVI, and 1 usb, then using a usb hub split it into mouse, keyboard, maybe even audio (2-3 cables) HDMI Option: If I get a new video card and monitor that supports HDMI, would I be able to run both audio and video through it? Would the monitor have to have an audio out? Also there is a lot of extra bandwidth in the HDMI cables, could I send two monitors on 1 cable or would I have to use 2 cables? How about sending mouse/keyboard through the HDMI cable? I see a lot of monitors with USB hubs built in, but I assume I'd still have to wire HDMI + 1 USB cable to use the USB hubs? X Terminal Machine/Thin Client: I don't really know much about this option. Not sure if it would allow me to run graphics acceleration and watch movies, does anyone know more details about what this would allow me to do? Other options: Any other ways to do this? Can any of this be wireless?

  Read the article

• Hibernate & Sleep broken after IE 9 RTM installation in Windows 7 x64.

  - by AKa

  I have a question about hibernation. I installed Internet Explorer 9 RTM x64 on my Windows 7 x64 SP1 desktop machine. After this, computer don't entry the hibernation or (hybrid) sleep state properly. After I hibernate the computer the monitor become blank screen and the keyboard and mouse are inactive. But the machine is still running and there isn't any possibility to switch them off as only with power button. But this is recognized on next start as ineligible because of log entry with message “The previous system shutdown at xx:xx:xx on ?xx.?xx.?x was unexpected“ and menu with safe mode option. I’m clearly not sure if it has something to do with Internet Explorer installation, but I’m definitely guaranteed that before of this I never had some problems with hibernation or (hybrid) sleep. In Windows logs isn’t something suspect. I switched the hibernation off and on, installed new drivers for mainboard, graphic and network card, checked the hard disk, nothing was helpful. This is really sad, beacuse I don't like to switch the computer completely off because it takes longer to boot. Any suggestions?

  Read the article

< Previous Page | 283 284 285 286 287 288 289 290 291 292 293 294  | Next Page >