Search Results

Search found 3683 results on 148 pages for 'lucky luck'.

Page 29/148 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Deactivated wifi drivers, now they wont activate again?

  - by UbuntuFan

  I have ubuntu 13.04. In the software and update menu, under additional drivers, Were it says "Broadcom Corporation; BCM4312 802.11b/gLP.PHY" the box labbeled "do not use it ticked" and when i try tick the one that says "Using Broadcom 802.11 Linux STA Wireless drivers....." it wont let me apply changes, it starts doing it then stops and re-ticks the do not use box. Because of this I can not use the wiress driver. Is there another way i can fix this. Or maby restore ubuntu to previous date. I accidentally ticked the do not use box this morning and now can't undo it. I have restarted several times to try apply changes and still no luck

  Read the article

• Xen Disk Performence Issues

  - by user98651

  I'm currently using Xen PV on CentOS 5 with my domU's as flat files running on a hardware RAID controlled (write cache enabled) formatted with XFS. On the dom0 I can get about 500MB/s in a 2GB dd write from /dev/zero however on the domU's I'm lucky if I get 10MB/s (it is usually around half that). I've tried changing the disk scheduling to NOOP on the domU's, changed some mount parameters and tweaked the performance allocations of both the dom0 (prioritize CPU) and domU's (increase RAM and VCPU allocations). None of these steps have produced any noticeable change in performance. My instinct here is that it is not a hardware problem, due to the solid performance of the dom0. Any ideas on what might be causing this problem? I'm considering moving to LVM based domU's.

  Read the article

• Problem with Arcam rpac and Ubuntu 12.04

  - by user108393

  I have recently (?mistakenly) purchased an Arcam rpac USB DAC for my Ubuntu (12.04) PC. I have torn out all but 3 of my hairs trying to get this to work and have had absolutely no luck so far. I can see the Arcam USB audio device when i run aplay -l, however I cannot see it listed under the Sound settings. I can see the soundcard device when running alsamixer also, but if I try and select it, alsamixer crashes, stating "cannot load mixer controls: Invalid argument". Any ideas how to get this working (if it's even possible)? Does anyone else out there have the rpac with ubuntu? Thank you! Aman

  Read the article

• Remove DRM From a WMV file I own

  - by Rev

  Alright, first, let me explain. I purchased some content through Microsoft's Zune/Xbox Video service, and man that was a mistake. After trying several times to get the video to play, I received an error along the lines of "out of licenses." Lucky for me, I was able to recover the file I was looking for off of a backup, but now I'm having problems playing it. It works fine in Windows Media Player, but not in Zune or Xbox Video (on Windows 8). I contacted Zune's customer support, and of course they couldn't help me. So, I legally own the content, I just want to be able to play it where I want to play it. It's ridiculous that I can't. I know there are ways to do this out there, I just can't figure it out (I keep getting directed to this piece of junk thing called Almedia, which kind of seems to work, but was only putting out audio in the demo version). Thanks!

  Read the article

• What should a programmer's yearly routine be to maximize their technical skills?

  - by sguptaet

  2 years ago I made a big career change into programming. I learned various technologies on my own without any prior experience. I really love it and feel lucky with all the resources around us to help us learn. Books, courses, open-source, etc. There are so many avenues. I'm wondering what a good routine would be to follow to maximize my software development skills. I don't believe just building software is the way, because that leaves no time for learning new concepts or technologies. I'm looking for an answer like this: Take a new concept sabbatical/workshop 2 weeks per year. Read 1 theoretical and 1 practical programming book per year. Learn 1 additional language every 2 years. Take a 1 week vacation every 6 months. Etc. I realize that the above might sound naive and unrealistic as there are so many factors. But I'd like to know the "recipe" that you think is best that will serve as a guide for people.

  Read the article

• Is it possible to start an additional X server after the system boots in 12.04?

  - by jackweirdy

  I'd like to have 2 VT's running, one on VT7 with the standard lightdm + unity interface and another on VT8 running a custom script which will launch a virtual machine in full screen. At the moment I've tried writing an init.d script with no luck and I can't find any details on a configuration file which will allow me to start 2 servers. I suppose my ideal answer would be one which points me to a config file I can edit to start up an additional server. Edit - I forgot to mention in the text that I already know how to start another X session: I'd like this to start automatically at boot.

  Read the article

• Installing Ubuntu 13.10 'Saucy Salamander' on L75D-A7280 hangs on a black screen

  - by Riven

  Trying to get Ubuntu 13.10 to work and it will not. Seen that somebody is having a similar problem, some things failing then it just hangs on a black screen (after pressing F1 to see what it's doing). My system is a Toshiba Satellite L75D-A7280, and I have tried two different files that I had downloaded from Ubuntu.com with no luck. My laptop came with Windows 8 and following the dual-boot directions Ubuntu 12.04 was installed and worked perfect, except for completely obliterating Windows 8 and voiding my warranty, meaning neither Toshiba nor the retail center I bought my system from can help me legally, besides giving advice... nor can I return it to get a non-UEFI based system. I really need to figure this out, I am a student and need my laptop working properly with any OS I put on it. Will continue searching for any information I can find.

  Read the article

• How can I get Kindle for PC to work in Ubuntu using Wine?

  - by codeLes

  I've 'installed' Kindle using Wine but it doesn't work. The menu item is there but nothing seems to happen when I click it. I have set the application settings in Wine config to run Kindle as Windows 98 as I've seen suggested... still no luck. Any experience with this? EDIT I don't have a kindle, but I use kindle for android. I was wanting to be able to read my books on my pc without having to use windows.

  Read the article

• WSS Fails Installing On Step 5 Of The SharePoint Products and Technologies Configuration Wizard

  - by ptahiliani

  I've attempted to install WSS 3.0 with SP1 several times as both stand-alone and server farm with no luck on Windows Server 2008.  When I get to step 5 of Configuration wizard it begin installing and publishing services but on Step 5 I get the message "Failed To Register Sharepoint Services". The detail behind this message reads "An exception of type Microsoft.SharePoint.SPException was thrown". Then I Run the command psconfig -cmd configdb -create -database <whatever_unique_name> Click on Start / All Programs / Administrative Tools / SharePoint Products and Technologies Configuration Wizard Should work now (it did with me). PS: This was done on a Virtual Machine (VMware)

  Read the article

• Network connection on an Acer Aspire 5253?

  - by fuquam

  Brand new to Ubuntu and PCs for that matter. I've been a Mac user all my life but wanted to try Ubuntu on the cheap, so I bought an Acer Laptop 5253-BZ893 and i got Ubuntu 10.10 installed with no problem. The only problem i have is, that i get no network connection options, wired or wireless. I just get No Network Devices Available. The computer came with Windows 7 installed and i am able to connect to my wireless network fine using Windows, so i know the computer works. Also i've been searching forums and google for hours trying to figure out why I can't get a network connection in Ubuntu but so far no luck. Any suggestions? Thanks in advance.

  Read the article

• Enable 'mod_rewrite' Using .htaccess File On cPanel Shared Hosting Server

  - by zulhfreelancer

  I'm using cPanel to host my website. I need to enable 'mod_rewrite' on this Shared Hosting cPanel account to run my script. I've tried to Google the solutions high and low but did not find any luck yet. Those tutorials that I found only work well with VPS and some of them said that, only hosting provider can change and enable it. But, some of them said that, it can be done easily by editing the .htaccess file. My question: If I want to edit the .htaccess file, what should I include in that file? What the 'rules' and 'conditions' that should be included?

  Read the article

• Can't install Ubuntu 13.10 from 12.04 lts

  - by Matt Carle

  I have ubuntu 12.04 lts installed on my hp pavilion and I want to try 13.10. When I try to boot into the livecd, I get the purple ubuntu splash screen, then a blackscreen where some text flashes (to fast to see what it says) then it goes to a black screen and stays there. I know the installation disc is not the problem because I've successfully installed it on a different machine using the same disc. I've been trying to troubleshoot the issue for a while now and no luck. I have a radeon hd 8250 card. I know it's not much to go off of but any help would be greatly appreciated! Thanks!

  Read the article

• Windows not recognizing its system drive after installing Ubuntu 11.10 alongside with windows 7. What to do?

  - by user53322

  After installing Ubuntu 11.10, it boots perfectly. But when I select Windows 7 from the GRUB menu, it restarts after showing the boot logo. I tried to repair the boot loader but the process failed. Then I decide to repair with system recovery disc. There I realize the system is unable to find any existing system. Then I boot into ubuntu and here I can see all the existing drive (with all content). All drives are still NTFS file system (I have 4 drive: 3 are NTFS another 1 is ext4). Tried to repair with gparted partition tool, but came with no luck. Also tried to reinstall windows but installer don't show any available drive. What to do? (something to do with Ubuntu?)

  Read the article

• 12.04 reboots rather than shutting down

  - by Luca

  I have a ruvo with a fresh installation of 12.04. When I try and shutdown the computer reboots. Until I upgraded (by doing a fresh install) I ran it with Ubuntu 10.04 and I didn't have this issue. I have tried sudo shutdown -h now sudo shutdown -P now sudo init 0 sudo poweroff All of these cause a reboot. I have added acpi=norq to my grub file as suggested by someone in the first post below. This is being used as a mythtv frontend and I would like the power button to shut it down. I have modified the button to perform a shutdown -h now, but this too causes a reboot. I have studied the posts below and tried some of these ideas, but with no luck so far. Why do I get a reboot instead of a shutdown? Ubuntu 12.04 not shutting down properly Stuck on reboot and shutdown Shutdown does not power off computer

  Read the article

• Error creating an .img file from an .ISO (MD5 verified)

  - by Rob

  I was following the instructions on this website to create a bootable USB flash drive on a Mac: http://www.ubuntu.com/download/help/create-a-usb-stick-on-mac-osx The instruction: hdiutil convert -format UDRW -o ~/path/to/target.img ~/path/to/ubuntu.iso does not create a valid file that the disk utility can copy to the USB drive, making installation on a USB drive useless. I've been repeating these instructions for days with no luck. The only thing that does not work is the .ISO to .IMG conversion. Is there a way to download Ubuntu 12.04 LTS 64-but Desktop in a .IMG file already? Unfortunately, my install notebook does not have an optical drive so USB is the only way. Thanks for your help!

  Read the article

• How to share/access to partition from ubuntu vmware

  - by chr

  I am beginner at Ubuntu. Here is my problem. I have Ubuntu installed on my external HDD and i am running XP through vmware on Ubuntu, because my internal disk is dead atm. External HDD have ext4 (37gb) and 2 NTFS partition (36gb and 220gb). My question is, how i can access that 220gb (or 36gb) NTFS partition from vmware XP? I was already try search for similar posts but no luck to solve my problems. Thank you in advance Regards

  Read the article

• How do I get a Realtek Wireless USB Airlink101 AWLL5088 working?

  - by Tobias_Mann

  I am running Ubuntu 11.10, 32bit. I ordered them a Realtek Airlink101 AWLL5088 based upon the relative ease for linux installation. I am having trouble installing the drivers. I copied the drivers to /usr/src/ and ran sudo ./install.sh from that director listed above. I have tried ndiswrapper, and allowing the default drivers, but with no luck. It seems to continue to try and use the default free drivers, even though I have blacklisted them using the guide described here. There was no error, I was asked which card I was using. I looked at the packaging and at the support page, and guessed number 2, allowed to finish, and rebooted. It continued detect the wireless network after the reboot, but would never complete the connection. I would appreciate any feedback. I am kind of stuck trying to figure this out.

  Read the article

• No sound after updating from 11.10 to 12.04

  - by shaneo

  Hi I updated a friends computer from 11.10 to 12.04 and the sound stopped working in the built-in speakers. The computer is a Sony Vaio PCG-2J1L. I tried using the guide found here: https://help.ubuntu.com/community/HdaIntelSoundHowto and still no luck. $cat /proc/asound/card0/codec* | grep Codec Codec: Realtek ALC889 $cat /proc/asound/card0/pcm0c/info card: 0 device: 0 subdevice: 0 stream: CAPTURE id: ALC889 Analog name: ALC889 Analog subname: subdevice #0 class: 0 subclass: 0 subdevices_count: 1 subdevices_avail: 1 cat /proc/asound/card0/codec* output can be found here http://paste.ubuntu.com/1043188/ If anymore information is needed just let me know and ill post it here. Thank you in advance for any help with this issue.

  Read the article

• Change from static HTML file to meta tag for Google Webmaster verification

  - by Wilfred Springer

  I started verifying the server by putting a couple of static HTMLs in place. Then I noticed that Google wants you to keep these files in place. I didn't want to keep the static HTMLs in, so I want to switch to an alternative verification mechanism, and include the meta tags on the home page. Unfortunately, once your site is verified, you never seem to be able to change to an alternative way of verification. I tried removing the HTML pages. No luck whatsoever. Google still considers the site to be 'verified'. Does anybody know how to undo this? All I want to do is switch to the meta tag based method of site ownership verification.

  Read the article

• Using "MTNL 3G Jadoo" data card on Ubuntu

  - by amolbk

  I am trying to use "MTNL 3G Jadoo" data card (Teracom LW272) with Ubuntu 12.04. On connecting, it gets mounted as a drive containing the client installation .deb file. I opened the .deb file in Ubuntu Software Center and installed it. I searched for "MTNL" in Ubuntu search and found "MTNL 3G Modem" application. But it won't run. I found it is installed in /opt/MTNL-3GModem. I tried running it from the terminal as: sudo /opt/MTNL-3GModem/ModemClient, but no luck. Any idea how to get it working?

  Read the article

• Unable to execute binary file. Exec format error

  - by user2689020

  I recently heard about Breach, a Node.js based browser. I was following the instructions on http://codeforgeek.com/2014/08/download-install-breach-browser-ubuntu-14-04/ to install it but got the following error : breach-v0.3.22-alpha.6-linux-x64/__AUTO_UPDATE_BUNDLE__/exo_browser/exo_browser: cannot execute binary file: Exec format error After some googling, I found that it is because I am trying to install the 64 bit package on the 32 bit Ubuntu installation. I tried to find 32 bit package of the same but ended up with no luck. The browser is only available in 64 bit packet(as far as i know). So, My question is : Is it possible to somehow install it on the 32 bit OS or if any program available which can run 64 bit applications on the 32 bit OS. I have been googling around and found no help. Can anyone help me? I am using Ubuntu 14.04 (32 Bit). Thank You

  Read the article

• Ubuntu One Client 3.02b stuck at "File Sync Starting" on Windows XP 32-bit

  - by user1491665

  I have been using Ubuntu One on Natty on my laptop and (sad) Win-XP 32-bit on my desktop. At first, the sync function worked well on both platforms but now it's stuck at "File sync starting" on Win-XP 32-bit. I have already tried to uninstall it completely (removed device, deleted folder, restarted pc) and reinstall it but no luck. It is able to display a list of "My Personal Folders" though. I did some Google-ing and found someone had similar problem on Win7 64-bit and some said the bug is resolved since version 3. Unfortunately that's not the case for me. As the title suggests, I am running v3.02b on WinXP. Any help / comments would be greatly appreciated. Thanks!

  Read the article

• Unable to use separate X-Screen's GTX 550ti Ubuntu 12.10

  - by user12622

  I am currently trying to get from "Twin View" to using separate X screen's on Ubuntu 12.10, however I'm not having a great deal of luck. I am using an Nvidia GeForce GTX 550 Ti and am on driver version 304.51 Initially, when I turn on the separate X screens option, presents me on the 1 monitor with a box to accept the changes, however the 2nd screen goes black, and effectively, Ubuntu only seems to recognise the one screen. When I reboot, I boots back into Ubuntu with both screens working in Twinview. I'm not too sure where to start, but my xrandr can be found: Xrandr Any help is greatly appreciated, this is the last but one thing I need to make Ubuntu my only OS, so fingers crossed we can crack it :)

  Read the article

• My wireless connection isn't working well

  - by Maikel Braas

  So this is my problem, I intalled ubuntu 12.04 with the wubi.exe and everything works fine, but my internet connection. When I try to install a program or use firefox, it goes with 24kb/s with a little luck for 1-2 seconds and then my internet terminates and it starts up again after 3-5 mins. Then it goes with an other 24kb/s and this will repeat. The thing is my connection works perfectly with windows. The laptop its running on is a Acer ASPIRE V3-771G. I tryed using a different network adaptor but that didn't help either. Please, some one help me with this. friendly regards, Maikel

  Read the article

• updating from 8.04 to a newer version?

  - by user175802

  I have an old system. It doesn't have a DVD drive, and I think the cd drive is a bit wonky. The only disk that I have been able to get to install is an old (official) 8.04 Kubuntu disk. No disk that I've burned on a few systems works. They check out, but they don't seem to survive the install (another issue). I thought once I got a version on that I could update over the web, but no luck. It appears EOL. No updates seem to be available, or software to install. Is there a way? I'd like to get it to as new a version as possible. The next step would be to pull the drive and get a new one, but I'd rather not.

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >