Search Results

Search found 16499 results on 660 pages for 'g off'.

Page 290/660 | < Previous Page | 286 287 288 289 290 291 292 293 294 295 296 297  | Next Page >

• Missing Wireless access point

  - by nvcnvn

  I have an: Ubuntu 12.04 with proprietary Boardcom STA Wireless driver installed BCM43224 802.11a/b/g/n wireless card TP-LINK TD-W8101G 54Mbps Wireless ADSL2+ Modem Router Yesterday before I went to sleep, I still connect to my wireless access point, this morning when I start my laptop I don't see it in the list - there are some neighbors listed but not mine. The WLAN is green, with my old Nokia E72, I still see my access point with 100% signal. I have tried to restart my laptop and turn the firmware off/on by the switch but no help. I have read the WirelessTroubleShootingGuide but I can do anything. Here is some of my card info: *-network description: Wireless interface product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: c0:cb:38:06:5d:53 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 03 serial: f0:4d:a2:42:ab:e4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:5000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff memory:f0420000-f043ffff

  Read the article

• Can I temporarily leave other roles active when converting a 2008 R2 server to a hyper-v host?

  - by Eric

  I currently have a Windows 2008 R2 box that I want to convert to a hyper-v host. Currently I have the following running on it: File Services, Web Server (IIS), and Sql Server 2008 R2 with a few different DBs. In the long term, I'd like to move all of those over to the VMs that will be created. However, in the short term I'd like to leave them running on the server. Are there any complications/problems with leaving them running on the hyper-v server for a day or two? How long will those services typically go down during the addition of the hyper-v role? Right now my plan is to back up everything, enable the hyper-v role, set up VMs, and migrate stuff off of the host. However, if there is a good probability that something may cease to function I might need to migrate everything over to a temporary host before doing the conversion.

  Read the article

• Should root ever own files in my (linux) home directory?

  - by Darren Cook

  This question started off asking why my history file wasn't working properly. Then I noticed it was -rw------- 1 root root and hadn't been updated since 2012-09-11. I changed the ownership, problem fixed. But now I see some other files are owned by root: .gitconfig .pearrc .viminfo Can I safely change them to be owned by my normal user, not root? I'm scratching my head trying to work out if there is a downside, or a security consequence. Losing seven weeks history is actually quite painful, because I lean on it a lot (e.g. to remind how I last did an archive). Would it be reasonable to set up a cron job to email me if it finds any files in my home directory owned by anyone else but me? Rephrased: is there ever a good reason for root to own a file in my home directory?

  Read the article

• E-Business Suite Proactive Support - Workflow Analyzer

  - by Alejandro Sosa

  Overview The Workflow Analyzer is a standalone, easy to run tool created to read, validate and troubleshoot Workflow components configuration as well as runtime. It identifies areas where potential problems may arise and based on set of best practices suggests the Workflow System Administrator what to do when such potential problems are found. This tool represents a proactive way to verify Workflow configuration and runtime data to prevent issues ahead of time before they may become of more considerable impact on a production environment. Installation Since it is standalone there are no pre-requisites and runs on Oracle E-Business applications from 11.5.10 onwards. It is installed in the back-end server and can be run directly from SQL*Plus. The output of this tool is written in a HTML file friendly formatted containing the following on both workflow Components configuration and Workflow Runtime data: Workflow-related database initialization parameters Relevant Oracle E-Business profile option values Workflow-owned concurrent programs schedule and Workflow components status Workflow notification mailer configuration and throughput via related queues and table Workflow-relevant recommended and critical one-off patches as well as current code level Workflow database footprint by reading Workflow run-time tables to identify aged processes not being purged. It also checks for large open and closed processes or unhealthy looping conditions in a workflow process, among other checks. See a sample of Workflow Analyzer's output here.  Besides performing the validations listed above, the Workflow Analyzer provides clarification on the issues it finds and refers the reader to specific Oracle MOS documents to address the findings or explains the condition for the reader to take proper action. How to get it? The Workflow Analyzer can be obtained from Oracle MOS Workflow Analyzer script for E-Business Suite Workflow Monitoring and Maintenance (Doc ID 1369938.1) and the supplemental note How to run EBS Workflow Analyzer Tool as a Concurrent Request (Doc ID 1425053.1) explains how to register and run this tool as a concurrent program. This way the report from the Workflow Analyzer can be submitted from the Application and its output can be seen from the application as well.

  Read the article

• Installing 10.10+ with Radeon HD 6970 Video Card

  - by Ben Lacy

  I built a new PC that has a Diamond Radeon HD 6970 graphics card, and no on-board graphics. When I boot from the Ubuntu disc, it runs through some initial booting stuff, and then gets to a loading screen that just has the Ubuntu logo and some progress bar/dot thingies. After this screen is finished, it goes black and says it cannot display video mode. I've seen many people that say to simply install the ati drivers. However, I don't believe this is an option, because I can't even get to the boot screen that asks me if I want to run the system off of the LiveCD, boot to hard disk, etc... Is there a way to somehow boot to a CLI before getting to the screen that would normally let me choose that? I'm at a loss as far as what to do. Also: Yes, the CD boots fine on other machines. (I've also burnt a couple discs just to be sure) Yes, the graphics card is fine. I normally dual-boot with Windows 7, and it runs on Windows just fine. Thanks for any help!

  Read the article

• S3200SH error 5220 every boot (CMOS/NVRAM Cleared by jumper)

  - by TechAUmNu

  I have a S3200SH Intel server board with a Intel Xeon 3220 Quad Core. Every time I boot it, I get error 5220 (CMOS/NVRAM Cleared by jumper). The jumper is not installed and I have replaced the lithium battery. The board overheated once, although still seems to work fine apart from this error. Also if I leave the board sitting in the bios for a while it sometimes randomly turns off, with all 4 diagnostic LED's red. I have moved the 2GB DIMM to another slot, which seems to have fixed this problem. Any ideas would be greatly appreciated.

  Read the article

• Black Screen after Resume from Sleep (Kubuntu)

  - by user20271

  I know there is a lot of other posts like this, but I have been looking for hours and I still haven't found any solution. I have recently installed Kubuntu Linux along side my Windows 7, the sleep on my Win7 works fine and resumes like normal. When I am loaded into Kubuntu, and I put my laptop to sleep, it goes into sleep as normal. When I go to RESUME from the sleep, the screen stays solid black, it doesn't light up, no blinking curser or anything. The Wi-Fi light is 'off' (orange) and I cannot turn it on. The Caps lock and the Num lock lights on the keyboard blink slowly. I hear something on the inside of the computer start to spin. I am not very experienced with Kubuntu/Linux, but I do know a bunch of computer terminology, I am still far from an expert though. I have about 300GB designated to my Win7 stuff, and another partition with about 100GB for my Kubuntu Linux. My computers specs are as follows: Windows 7 64-bit I have the most recent version of Kubuntu because I just downloaded it a few days ago and updated it yesterday. AMD Athlon Duel-Core processor 4GB of RAM And it is a HP G61 Laptop

  Read the article

• Can't connect to sql server 2008 named instance

  - by hcsrpm

  I have sql server 2005 and 2008 running on a server on my local (and very straightforward) network. Using sql management studio 2008 and visual studio 2008, I can connect over the network to the 2005 instance which is the default instance. I can't connect to the 08 instance (named MC08). I can connect to both when logged in to the server. Remote connections have been enabled for MC08 and dynamic ports is turned off (assigned to port 1045). The sql browser service is running as well. This used to work so I'm not sure what has changed. I can't connect using the IP address either. Nothing unusual in the event log either. Any ideas?

  Read the article

• Is the motherboard the cause of these errors?

  - by ianfuture

  Motherboard is : ASUS A7N8X-E Deluxe, Rev1.01, On start up get: "cmos checksum error - defaults loaded" error BIOS is reset everytime and can't boot to Windows off HDD. POST report is ok once I tell it there is no Floppy drive attached and not to seek it. The boot sequence starts then just as get to load windows safe mode options whole PC shuts down. BIOS is reset to defaults again. I've checked the battery and jumpers. Tried a known working battery. Changed Graphics card, changed memory, changed HD to one without an OS. Disconnected DVD drive. PSU is known to be ok. IN BIOS CPU is recognised correctly and memory is also recognised ok. So is it likely to be a bad motherboard or corrupted BIOS or something else? Thanks :)

  Read the article

• Chrome "refusing to execute script"

  - by TestSubject528491

  In the head of my HTML page, I have: <script src="https://raw.github.com/cloudhead/less.js/master/dist/less-1.3.3.js"></script> When I load the page in my browser (Google Chrome v 27.0.1453.116) and enable the developer tools, it says Refused to execute script from 'https://raw.github.com/cloudhead/less.js/master/dist/less-1.3.3.js' because its MIME type ('text/plain') is not executable, and strict MIME type checking is enabled. Indeed, the script won't run. Why does Chrome think this is a plaintext file? It clearly has a js file extension. Since I'm using HTML5, I omitted the type attribute, so I thought that might be causing the problem. So I added type="text/javascript" to the <script> tag, and got the same result. I even tried type="application/javascript" and still, same error. Then I tried changing it to type="text/plain" just out of curiosity. The browser did not return an error, but of course the JavaScript did not run. Finally I thought the periods in the filename might be throwing the browser off. So in my HTML, I changed all the periods to the URL escape character %2E: <script src="https://raw.github.com/cloudhead/less%2Ejs/master/dist/less-1%2E3%2E3.js"></script> This still did not work. The only thing that truly works (i.e. the browser does not give an error and the JS successfully runs) is if I download the file, upload it to a local directory, and then change the src value to the local file. I'd rather not do this since I'm trying to save space on my own website. How do I get the Chrome to recognize that the linked file is actually a javascript type?

  Read the article

• 'Binary XML' for game data?

  - by bluescrn

  I'm working on a level editing tool that saves its data as XML. This is ideal during development, as it's painless to make small changes to the data format, and it works nicely with tree-like data. The downside, though, is that the XML files are rather bloated, mostly due to duplication of tag and attribute names. Also due to numeric data taking significantly more space than using native datatypes. A small level could easily end up as 1Mb+. I want to get these sizes down significantly, especially if the system is to be used for a game on the iPhone or other devices with relatively limited memory. The optimal solution, for memory and performance, would be to convert the XML to a binary level format. But I don't want to do this. I want to keep the format fairly flexible. XML makes it very easy to add new attributes to objects, and give them a default value if an old version of the data is loaded. So I want to keep with the hierarchy of nodes, with attributes as name-value pairs. But I need to store this in a more compact format - to remove the massive duplication of tag/attribute names. Maybe also to give attributes native types, so, for example floating-point data is stored as 4 bytes per float, not as a text string. Google/Wikipedia reveal that 'binary XML' is hardly a new problem - it's been solved a number of times already. Has anyone here got experience with any of the existing systems/standards? - are any ideal for games use - with a free, lightweight and cross-platform parser/loader library (C/C++) available? Or should I reinvent this wheel myself? Or am I better off forgetting the ideal, and just compressing my raw .xml data (it should pack well with zip-like compression), and just taking the memory/performance hit on-load?

  Read the article

• Does Juniper Networks provide keyloggers with their software?

  - by orokusaki

  I noticed that I had a "USB Mass Storage Device" plugged in when there wasn't in fact anything plugged in to any USB port. I turned it off via Windows (XP), but it's quite concerning. This was after installing Juniper Networks' software for VPN access to an IT guy's stuff. I also notice there is a service called "dsNcService.exe" which apparently is sending information over the internet (even when I'm not in VPN access). The process restarts itself when I end it. Should I be worried that this software is tracking my keystrokes and broadcasting them to my IT guy?

  Read the article

• How to capture footage from an analog TV?

  - by hope

  I have only an old analog TV with just RCA connectors and a coaxial/cable in/out wire. It uses no HDMI interface, etc. I would like to know the cheapest method possible where the current video footage can be transferred and made into a target digital video file format and be copyable/transferrable via USB. Are there any devices that can do this with an analog TV? Basically, how can I get something along these lines done and for cheap?P I do NOT want to stream; I want footage recorded off the TV and stored via a digital encoding of a video file.

  Read the article

• Blank screen after Switch User or Resume

  - by matt wilkie

  About half the time when I switch users or resume from standby or resume the screen goes blank (black). If I work the cursor keys I can hear the system bell when it gets to the end of the user list. I can also successfully login, going from memory, but screen stays black. Sometimes closing and re-opening the lid will light up the screen again. Pressing the special Function key to enable/disable external monitor connection has no effect [Fn]-[F5],[Fn]-[F6]. If none of the previous work I need to put the computer into hibernation or full power off to restore screen function. If I watch closely when switching users I think I can see the screen initially start to light up and then quickly fade to black. The computer is an Acer Aspire 3500, model ZL6, running Ubuntu 10.10 installed 2 days ago. No proprietary drivers are in use. I'll provide a list of hardware details as soon as I can figure out how to generate that (didn't there used to be an entry for hardware details under the System menu?). Possibly related questions: No resume after Hibernate or Standby When I resume from suspension - the screen is blank Switch user fails to complete successfully For what it's worth, blank after resume also used to happen occasionally when the laptop was running XP-Home, but nowhere near as often, perhaps 6 or 8 times a year. UPDATE: I found System Administration System Testing and ran the Monitor test. It went very very dark, but the window elements could be discerned, and the whole screen flashed (from very very dark to black). On the third repeat of that same test the screen went to full blaupck and stayed there. Moving the mouse, via touchpad, or touch keys did not wake it up again. I had to close the lid and put the computer into hibernate, and press the power button to restore it. UPDATE2: output of lshw: http://pastebin.com/q7n8676r, lspci: http://pastebin.com/6ujzVK4r UPDATE3: sometimes I can restore the screen by flipping to console 1 with ctrl-alt-F1 and then back to graphical with ctrl-alt-F7.

  Read the article

• Configuring IIS 7.5 to be FIPS 140.2 compliant

  - by tomfanning

  I need to configure IIS 7.5 (Server 2008 R2) to be FIPS 140.2 compliant. Specifically, this involves disabling all SSL protocols other than TLS 1.0. I have set the following registry keys: HKLM\SYSTEM\CurrentControlSet\Control\SecurityProviders\SCHANNEL\Protocols\SSL 2.0\Server HKLM\SYSTEM\CurrentControlSet\Control\SecurityProviders\SCHANNEL\Protocols\SSL 3.0\Server HKLM\SYSTEM\CurrentControlSet\Control\SecurityProviders\SCHANNEL\Protocols\PCT 1.0\Server to Enabled(DWORD) = 0 as per this KB, but SSL Labs' checker says "SSL 2.0+ Upgrade Support" is enabled. (Everything other than that and TLS 1.0 is not available, so we're getting somewhere). It also says "FIPS ready - no" - presumably because SSL 2.0+ Upgrade Support is still enabled. serversniff.net says SSL 2.0 is turned off, and doesn't say anything about SSL 2.0+ Upgrade Support. Could this be an anomaly with SSL Labs' checker?

  Read the article

• Dual booting Windows and Arch Linux (with GRUB2) - after using Windows, Windows Boot Manager made first in boot priority list

  - by louis058

  I am dual booting Windows 7 and Arch Linux (both 64bit), with GRUB2, using the 64-bit EFI version. I partitioned my drive into a GPT drive and installed Windows first according to this guide. I then installed Arch Linux using the Beginner's Guide, installing grub2-efi-x86_64 in the process. Everything is working fine now, but with one problem. I can set the boot priority in BIOS (or is it UEFI?) to have GRUB boot try and boot before Windows Boot Manager. Then I chainload Windows Boot Manager using GRUB. However, when I actually use Windows in this manner, upon shutting down and turning on again, or rebooting, Windows seems to set Windows Boot Manager first in the priority list again, with the result being I have to manually set GRUB again, or I can't boot into Linux. My motherboard is an Asrock H61M/USB3, if that helps. I want to know how to turn off this behaviour.

  Read the article

• Perl: Negative look behind regex question [migrated]

  - by James

  The Perlre in Perldoc didn't go into much detail on negative look around but I tried testing it, and didn't work as expected. I want to see if I can differentiate a C preprocessor macro definition (e.g. #define MAX(X) ....) from actual usage (y = MAX(x);), but it didn't work as expected. my $macroName = 'MAX'; my $macroCall = "y = MAX(X);"; my $macroDef = "# define MAX(X)"; my $boundary = qr{\b$macroName\b}; my $bstr = " MAX(X)"; if($bstr =~ /$boundary/) { print "boundary: $bstr matches: $boundary\n"; } else { print "Error: no match: boundary: $bstr, $boundary\n"; } my $negLookBehind = qr{(?<!define)\b$macroName\b}; if($macroCall =~ /$negLookBehind/) # "y = MAX(X)" matches "(?<!define)\bMAX\b" { print "negative look behind: $macroCall matches: $negLookBehind\n"; } else { print "no match: negative look behind: $macroCall, $negLookBehind\n"; } if($macroDef =~ /$negLookBehind/) # "#define MAX(X)" should not match "(?<!define)\bMAX\b" { print "Error: negative look behind: $macroDef matches: $negLookBehind\n"; } else { print "no match: negative look behind: $macroDef, $negLookBehind\n"; } It seems that both $macroDef and $macroCall seem to match regex /(?<!define)\b$macroName\b/. I backed off from the original /(?<\#)\s*(?<!define)\b$macroName\b/ since that didn't work either. So what did I screw up? Also does Perl allow chaining of multiple look around expressions?

  Read the article

• rEFIt can't sync GPT and MBR after resizing boot camp partition

  - by benwad

  I've been trying to follow the instructions here to increase the size of my boot camp partition: http://plonsdale.wordpress.com/2011/06/24/tech-tip-increasing-the-size-of-a-bootcamp-partition-with-free-tools/ I got as far as step 3 when I booted from the rEFIt CD. I selected the partitioning tool and it gave me the following message: Error: Not Found returned from gptsync.efi Now the Windows boot camp partition doesn't show up when I hold alt when starting my mac. Trying to boot into Windows using the rEFIt CD gives me a message saying no Windows installation is found. I then booted off the Windows 7 install CD and the 'repair' option gave me this message: This version of System Recovery Options is not compatible with the version of Windows you are trying to repair. Try using a recovery disc that is compatible with this version of Windows ...and if I try and go install a fresh version of Windows on this partition using the 'Custom (advanced)' option I get an error about the partition saying: Windows cannot be installed to this disk. The selected disk is of the GPT partition style

  Read the article

• Open Microsoft Publisher Document on Linux

  - by Peter

  I'm pretty sure the options consist of Just don't do it (use a nice open standard file format). Not great when someone sends you something. Translate the format on Windows. I think you need Publisher, the viewer won't even print. But you can download a trial version for a once off (been there, done that). Submit the file for online translation to PDF. www.pdfonline.com/convert-pdf/ Use a Windows VM, wine, crossover office, Win4Lin, or otherwise run Publisher "under" linux. What I really want to do is convert it to something nicer natively under Linux.

  Read the article

• Ubuntu 10.04 install - frozen at splash, no errors

  - by Andrew Bolster

  Has anyone else come across this? After about as much of a fresh install as i can muster without buying new drives, and after walking through the amd64 alternate install with ease, and after a little 'pre-splash' screen where the orange dots under the (very sexy) new ubuntu logo blink away, I'm left with a vista of purple hues and logo plonked in the middle, with the dots not going anywhere. I was at this same position last night at 3 in the morning, left it lying overnight, and nothing had changed, so I'm pretty sure its frozen, the virtual terminals are not accessible, ie, c+a+F1 etc does nothing, but when i go in and inspect /var/log/* in the recovery console by booting off the installation cd, no errors, no complaints, no problems. I'm at my wits end and am just about ready to try anything. If this was on SO I'd be bountying, but if anyone can help you'll just have to cope with my thanks! Additional Details on my blog and my first attempt at asking for help Update: I can reasonably say it is not a hardware fault, as a full install of 9.10 with dual screen nvidia xinemara indicate that nothing is wonky

  Read the article

• Best way to transfer files across unstable LAN?

  - by JamesTheAwesomeDude

  This is very similar to Question 326211, but in this case, the LAN is an unstable Wi-Fi connection. I need to transfer about 11 GiB of files between two computers, both running Linux (although one may be rebooted into Windows.) Their connection is both slow and unstable (due to Linux's awful Wi-Fi support,) but removable media (such as a flash drive or external hard drive) is not an option at this time. Right now, I'm slowly transferring the files, one by one, across SFTP, but I have to reconnect each computer approximately every 90 seconds, and the computers are not very close to each other, so this is not feasible. This is not a duplicate of Question 30186; that one specifically concerns Windows 7, and all the proposed solutions involve closed-source, Windows-only programs (which are all spyware IMHO, and are all off the table even if I trusted them - one of the computers is Linux-only.)

  Read the article

• Java ME SDK 3.0.5 is released!

  - by SungmoonCho

    Java ME SDK 3.0.5 went live! For many months, we have been working hard to fix bugs from previous version, and add a lot of new features demanded by Java ME community. You can download the new version from this link. Please see below for more information. NetBeans Integration All Java ME tools are implemented as NetBeans plugins. Device Manager Java ME SDK now supports multiple device managers. You can switch between different versions of device managers. LWUIT 1.5 Support The Resource Editor is available from the Java ME menu to help you design and organize resources for LWUIT applications. For a description of LWUIT 1.5 features, visit the LWUIT download page Network Monitor Integrated with NetBeans profiling tools, the Network Monitor now supports WMA, SIP, Bluetooth and OBEX, SATSA APDU and JCRMI, and server sockets. CPU Profiler Now uses standard NetBeans profiling facilities to view snapshots. Profiling of VM classes can also be toggled on or off. WURFL Device Database The database has been updated with more than 1000 new devices. Tracing - New tracing functionality now includes CLDC VM events, and monitors events such as exceptions, class loading, garbage collection, and methods invocation. New or updated JSR support - Includes support for JSR 234 (Advanced Multimedia Supplements), JSR 253 (Mobile Telephony API), JSR 257 (Contactless Communication API), JSR 258 (Mobile User Interface Customization API), and JSR 293 (XML API for Java ME).

  Read the article

• Is it OK to use images of GPD'd code in a CC 3.0 BY video?

  - by marcusw

  I am making a video in which I would like to use pictures of some Linux Kernel code. I am looking to release the finished product under the CC 3.0 BY license, but the Kernel is released under the GPL, which would not allow this if the code is in text format. However, since it will be in low-resolution, incredibly incomplete, non-usable, non-compilable, non-editable (at least without lots of finagling) format, would this constitute fair use or find another loophole to slip through? Thanks for the help, I will understand if this is considered off topic.

  Read the article

• Is it OK to use images of GPL'd code in a CC 3.0 BY video?

  - by marcusw

  I am making a video in which I would like to use pictures of some Linux Kernel code. I am looking to release the finished product under the CC 3.0 BY license, but the Kernel is released under the GPL, which would not allow this if the code is in text format. However, since it will be in low-resolution, incredibly incomplete, non-usable, non-compilable, non-editable (at least without lots of finagling) format, would this constitute fair use or find another loophole to slip through? Thanks for the help, I will understand if this is considered off topic.

  Read the article

• 2D map/plane with nodes overlayed that supports panning, scaling and clicking on nodes

  - by garlicman

  I'm trying my hand at Android development and seem to be running into an invisible ceiling in trying to get what I want accomplished. Basically I'm trying to create an app that renders a 2D surface map that I can (pinch) zoom and pan. I'll have to place nodes on the surface of the map that will scale/zoom and pan in relation to the surface. I started out with a 2D ImageView approach and got as far as pinch zoom, pan and laying nodes as relative ImageViews, but all the methods I tried to get X,Y,W,H for the 2D surface were always off for some reason. Additionally, I was never able to scale the node ImageViews correctly, and as a result never got far enough to try and work out their X,Y scaled offset. So I decided to get back to 3D rendering. Conceptually pan/zoom is camera manipulation, so I don't have to mess with how to scale the 2D map or the nodes. But I need a starting point or sample to get me going that's close to what I'm trying to achieve. A sample on a translucent spinning cube isn't helping as much as I need it to. Any tips? Links, insults and sympathy are all welcome!

  Read the article

< Previous Page | 286 287 288 289 290 291 292 293 294 295 296 297  | Next Page >