Search Results

Search found 10910 results on 437 pages for 'john speed'.

Page 294/437 | < Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >

• Why do msi installations use slower drives over faster ones in windows 7?

  - by Joshua C

  I have noticed that the slowest drive in my system is used most during an msi installation. I mainly notice this when running windows updates but it seems to be msi installs in general. The setup I last saw this occur on was running Windows 7 with the following drives: Sata: 240GB SSD NTFS ~515MB/s Operating system drive 1TB NTFS ~110MB/s Firewire: 4TB ExFAT ~80MB/s I would think that windows would choose the fastest drive with available space for temporary files. But it will instead choose the external drive with the slowest transfer speed. I could also understand choosing the 1TB for not being an ssd in an attempt to preserve the longevity of the ssd write capacity. Why does this happen? Is there a way to force these installations to use the OS drive or a specific drive?

  Read the article

• Unable to mount portable hard drive on Ubuntu

  - by VoY

  My portable hard drive (WD My Passport), which used to work correctly now does not automount on my Ubuntu system. It does work on a Windows machine or even when plugged into WD HD TV, which is a Linux based device. There's one NTFS partition spanning the whole drive. When I plug the disk in, I see the following in dmesg: [269259.504631] usb 1-2.2: new high speed USB device using ehci_hcd and address 20 [269259.604674] usb 1-2.2: configuration #1 chosen from 1 choice However it does not mount in GNOME and I don't see it when I type: sudo fdisk -l Any suggestions why this might be? I repaired the partition using chkdsk on Windows, so the issue is probably not filesystem related.

  Read the article

• Ubuntu: Take actions when system temperature gets too high

  - by Josh

  One of the CPU fans on my Compaq Presario laptop running Ubuntu 9.10 seems to have bit the dust. The fan is deep within the case and I intend to replace the laptop in the next 6 months so it's not worth replacing it. I have the laptop on a cooling pad and most of the time the system is fine, CPU temps around 90°-110°F. Occasionally, however, I'm seeing random lockups which I believe is due to the system overheating. How can I configure the system to: Lower the CPU speed when the temperature reaches a certain level? (I.E. 110°F) Shutdown the system when the tempature reaches a critical level? (And what would that be? 130°?)

  Read the article

• Choosing between cloud (Cloudfoundry ) and virtual servers - for developers

  - by Mike Z

  I just came across some articles on how to setup your own cloud using Cloudfoundry and Ubuntu, this got me thinking, choosing our infrastructure, if we want to use our own servers what's the advantage of cloud on virtual servers vs just using virtual servers, VPN? If we now develop for the cloud later if we need help we can quickly move on to a cloud provider, but other than that what's the advantage and disadvantage of private cloud in these areas? speed of development, testing, deployment server management security having an extra layer (cloud) will that have a hit on server performance, how big? any other advantage/disadvantage?

  Read the article

• WiX - create a bootstrap that passes arguments to the msiexec

  - by Dror Helper

  I need to create a bootstrap for my WiX project I've tried using setupbld.exe but it will only allow me to create an executable that will show my UI or one that will behave as a silent installer but not both. I need to be able to run the resulting executable with argument that will tell it wether or not to show the UI during installation. I've found this post by John Robbins that explains how to re-build the setup.exe stub used in the creation of the bootstrap but I was hoping there is a simpler way to do what I need. Does anyone know of a way to create a bootstrap that I use to run either as a simple (with UI) install or as a silent install.

  Read the article

• Populating PDF fields in .NET without a API, such as iTextSharp

  - by Kristjan Oddsson

  class mineTest { string pdfTemplate = @"c:\us.pdf"; public mineTest(Customer c, string output) { StreamReader sr = new StreamReader(pdfTemplate); StreamWriter sw = new StreamWriter(output); string content = sr.ReadToEnd(); content.Replace("(Customer name)/DA(/Verdana 10 Tf 0 g)/FT/Tx/Type/Annot/MK<<>>/V()/AP<</N 13 0 R>>>>", "(Customer name)/DA(/Verdana 10 Tf 0 g)/FT/Tx/Type/Annot/MK<<>>/V(John Johnson)/AP<</N 13 0 R>>>>"); sw.Write(content); sw.Close(); sr.Close(); } } Why does the above code fail at producing a valid PDF?

  Read the article

• "tar -cfz" versus "tar cf - | gzip": are they different? (or how to improve a backup)

  - by I'm Dario

  I want to speed up my backup done with "tar -cfz", the common way to do it. But day by day my backed up files grow so it becomes slower. I was thinking to take advantage of the several cores available in my server and I was wondering if there is any difference between doing the backup with "tar -cfz" or piping tar to gzip ("tar cf - | gzip"). I guess that there isn't any difference, because the first spawns two processes (tar and gzip), in a similar way like piping it. If there is not difference, do you know any good alternative to do this, without going incremental? I'm looking at pigz too and it looks fine.

  Read the article

• Reimage PC: Myth or Fact to speeding up a slow PC?

  - by sunpech

  I have a 4-5 year old PC running Windows XP for software development at work. It struggles to run all development tools I need at the same time. Management feels I need to reimage my computer to "speed it up". The last time it was imaged was about 3 years ago. What resources books, websites, blogs, articles, etc are out there that supports/debunks this well known belief that reimaging an old PC running Windows XP will make it faster once again? A resource I remember reading is from Lifehacker.com: Windows Maintenance Tips: The Good, Bad And Useless

  Read the article

• is it really necessary to run Apache as a front-end to Glassfish/JBoss/Tomcat?

  - by Caffeine Coma

  I'm primarily a Java developer, and I come to you with a question that straddles the divide between developers and sysadmins. Years ago, when it was a novel thing to run Tomcat as an app server, it was customary to front it with Apache. As I understand it, this was done because: Java was considered "slow", and it was helpful to have Apache serve static content directly. Tomcat couldn't listen to ports 80/443 unless run as root, which was dangerous. Java is no longer considered slow, and I doubt adding Apache to the mix will actually help speed things up. As for the ports issue, there are probably simpler ways to connect app servers to ports 80/443 these days. So my question is- is there really any benefit to fronting Java Webapps with Apache these days? If so, is Apache still the way to go? Should I look at Nginx? Instead of Tomcat I'm using Glassfish, if that matters.

  Read the article

• Netgear FVX538v2 slow whene connected to Canoga Perkins N525 ETSU

  - by Doomloard

  First of all thank you in advance for helping me. my issue is the old network admin found a problem whene he connected the firewall and the ETSU together the through put went down to less than 1 mega bit a second. his fix was to add a dlink router between the firewall and the etsu which speed it up to 5 mega bits a second. now my boss wants a more clean and proper solution if possible. i have check all the settings in the netgear it dose not seem to be a setting issue. if anyone can help that would be great.

  Read the article

• Very long DNS lookups inside my network

  - by Nuno Cordeiro

  Ever since I installed DD-WRT (v24-sp2 08/07/10 std-usb-ftp) on my router (RT-N16), my browsing got substantially slower. Using FirePHP I figured out that it's being caused by VERY long DNS lookups (~30 seconds). When the domain name was very recently accessed then speed is very good. I tried changing DNS on the computer and I tried messing around with the options on DD-WRT. I have tried to configure the router with Google DNS and/or OpenDNS. My current DNS output after using ipconfig -all is: 192.168.1.1 208.67.220.220 8.8.8.8 208.67.222.222 Can someone help me debug and solve this problem? I'd like to snoop the requests themselves. How can I know which DNS requests are being sent and which are failing/succeeding? Note: I don't expect this to be relevant but my router is connected to the internet through an ONT.

  Read the article

• Is to possible to achieve the SATA II's 3Gbps (375MBps) between home network storage and home computers?

  - by techaddict

  Gigabit ethernet only has 1Gbps (125MBps), whereas SATA II has up to three times that rate. Is it possible to achieve the rate of three times Gigabit ethernet connection which is SATA II speeds, between home network storage and the laptops and desktops with SATA II hard drives? If so, how? Or, is the limitation of a gigabit ethernet port on the laptops the limitng factor, making 1000Gbps the fastest practical transfer speed possible? (practical, meaning that without taking apart the laptop and doing physical modifications like branching a SATA II transfer cable, etc.) -- I just realized -- wouldn't a USB 3.0 cable do the trick? Since USB 3.0 can reach up to 675MBps?

  Read the article

• SATA Backward compatibility? [closed]

  - by Fladur

  Possible Duplicate: Can I connect a SATA-II hard drive to a SATA-I connection? Hello everyone One of my system is really old, but I still use it, right now, the HDD is and old IDE drive that is starting to fail (I got to many damaged sectors) and I'm planing to replace it. The motherboard supports Serial ATA 1 and I have a real nice offer on a SATA 2 drive, can I use that drive on a SATA 1 interface (obviously with reduced speed) just like a USB 2.0 device on a 1.0 port? Thanks in advance.

  Read the article

• Splitting Ethernet cable

  - by Nathan

  I am looking for the best way to network my small business. I have an office where my router/modem are located, and then 2 more computers in another room. I can route Ethernet to this room with about 75 ft of cabling, and I would like to do this because my computers on Ethernet are getting 3x the speed as computers on wireless. Is there any way I can use just one Ethernet cable to span the 75 feet, and then maybe 2 smaller ones to go to the two computers from there? If there's a simple way to do this, maybe with a connector that would be ideal, as opposed to buying over 150 ft of cabling. Thanks!

  Read the article

• Drive configuration for 5 large databases

  - by Mr. Flibble

  I've got 5 databases, each 300GB, currently on a RAID 5 array consisting of 5 drives. All the databases are used heavily, at the same time, so drive speed is an issue. Would I see better performance if I got rid of the RAID 5 configuration and just put each database on a separate drive? The redundancy provided by RAID 5 is not necessary due to mirroring elsewhere. Will the server then be able to perform reads / writes to different databases drives in parallel? More so at least than when it's in RAID? This is all on Windows 2003 / SQL 2008.

  Read the article

• .NET Framework 4.0 installation is very slow

  - by Dimitri C.

  On my Windows Vista, it takes a full 12 minutes to install the .NET Framework 4.0. a) Is this normal? b) If not, can something be done about it? The reason I'm concerned about the speed is because it slows down the testing of our product installer considerably. Testing an installer is time consuming already, but this new .NET Framework installer makes it almost undoable. Detail: I did the test on a clean Vista inside a VirtualBox virtual machine. This setup does not show any performance issues in other situations. I tried both dotNetFx40_Full_x86_x64.exe and dotNetFx40_Client_x86_x64.exe. They both take approximately the same time to install.

  Read the article

• Which browsers support Window's Low Integrity level?

  - by Ian Boyd

  Normally i like running ie, but it's rendering speed at high-dpi is poor. More recently i've switched to Chrome, but it does not support high-dpi displays. i'm interested in trying other browsers, but they must support protected mode. Are there any other browsers, besides IE and Chrome, that support Mandatory Integrity Levels (i.e. protected mode)? Browsers that i do know about: Browser Protected Mode High-dpi Aware ============== =============== ============== Internet Explorer Yes Yes Chrome Yes No Firefox No No Opera No No Are there any other? And just as an fyi, the clear, unambiguous, non-argumentative, non-subjective, question is: Are there any browsers, aside from Internet Explorer, available for Windows, that run at the Windows Low Mandatory integrity level, and support high-dpi (i.e. non-96 dpi) displays?

  Read the article

• Idle hard disk makes noise.

  - by ULTRA_POROV

  Like a fan or something. I checked it. I stopped all fans (cpu, video, psu) and the noise was still there. I read online that it might be a motor or something. I have put a great deal of effort making my pc quiet. Installed a quiet psu and cpu fan, reduced the fan speed of my video card, bought a ssd... But my drive for data makes this noise. I would never have expected that. Do all hard disks make this kind of noise? I guess most people won't notice it because of the other fans they have in the system, I however can hear it quite clearly because all my other fans are almost silent. So should i get a new one or should i just live with it, considering that i might end up with a drive that also makes this noise.

  Read the article

• Vista: Improving troubleshoot approach skills

  - by Chau

  I'm not a Windows SuperUser, but neither just the regular user. I don't mind browsing the Registry, using Process Explorer, reading the Event logs, (un)installing new drivers and so on, but all this only makes me solve some problems. I tend though to run into problems where these tools aren't enough. Which tools should I learn about to improve my troubleshooting skills in Windows? Currently I'm using Windows Vista x64 (not moved to 7 yet), facing audio/video stuttering problems and I think this is a good place to improve my troubleshooting skills. I know this post is similar to this question, but my machine is only hanging occationally. Specs: Intel Q6600 Stock speed ASUS P5QD Turbo 4GB ram NVIDIA GTS-8800 640 HDA Xplosion 7.1 Seasonic 430W Windows Vista Business x64

  Read the article

• Cisco asa 5505 locks up / unresponsive

  - by Chris

  We have a cisco asa 5505 that's new (in service for about 2 months) running 7.2(4) software. Every day around 10a it locks up for approx 10 minutes. We're monitoring it via snmp with stg, and snmp doesn't respond during that time. There's no output in the 'show crash' output. Internet connectivity is also dropped. Wondering if anyone else has seen this and what the fix might be. Currently we're looking at upgrading software, but will need memory upgrade for that. We've forced the speed and duplex on the internal and external interfaces, but the problem is still occurring. It's connected on the internal lan to a netgear 724 gige switch.

  Read the article

• Overclocking a nVIDIA GTX 660M GPU?

  - by heron1000

  I have a MSI GE60 0ND laptop with a GTX 660M GPU. When I play games like Minecraft or Portal 2, the core clock is stable at 835 MHz. Recently I tried to overclock it using MSI Afterburner but it wouldn't let me change the voltages or the clock speed no matter what I tried. Various Google searches yielded solutions that all didn't work. Is there any way I can overclock the GPU? Further Info: I have the nVIDIA 310.70 drivers and Windows 8.

  Read the article

• limit linux background flush (dirty pages)

  - by korkman

  Background flushing in linux happens when either too much written data is pending (adjustable via /proc/sys/vm/dirty_background_ratio) or a timeout for pending writes is reached (/proc/sys/vm/dirty_expire_centisecs). Unless another limit is being hit (/proc/sys/vm/dirty_ratio), more written data may be cached. Further writes will block. In theory, this should create a background process writing out dirty pages without disturbing other processes. In practice, it does disturb any process doing uncached reading or synchronous writing. Badly. This is because the background flush actually writes at 100% device speed and any other device requests at this time will be delayed (because all queues and write-caches on the road are filled). Is there any way to limit the amount of requests per second the flushing process performs, or otherwise effectively prioritize other device I/O?

  Read the article

• Can SATA be used to connect computers?

  - by André

  Can SATA be used to connect two computers together, just like a crossover Ethernet cable would do ? I know SATA has no "networking" features and even though a controller may have multiple ports, the drives don't "see" each other, and that in SATA one device acts as the host (the computer) and the other device is some kind of "client" (the storage drive). But still, did anyone attempt to make a kernel module that would make one computer appear as a "client" (so that the host's SATA controller detects it as a standard hard drive) and then set up like a pseudo-Ethernet link or a very high speed serial link (and then run pppd on it and do networking) ? Note : I know this is an unprofessional and totally stupid idea, I'm just asking out of curiosity.

  Read the article

• Monitoring CPU Usage Over the Course of a Day?

  - by bobber205

  Are there any apps I an install on client machines that will generate a report for me what app used what % of the CPU. We have some machines that are running, at times, VERY slowly. The machine will run really poorly then boom, back up to full speed. There isn't usually enough time to check Task Manager real quickly to see what is running, not to mention the majority of the time there are people using the computer that don't know what the Task Manager is. ;) It would be really nice to take a look at some logs and see if, maybe, the anti virus is randomly taking alot of CPU for stretches of time. Or another application. Thanks! EDIT: This is for Windows XP. Sorry for the oversight. :)

  Read the article

• Building a Social Networking website, should I have separate servers for certain parts of the site? [closed]

  - by Dylan Cross

  I have been working on building a social networking website, I'm pretty committed to this and I think I have something that could work out. I hope to be launching it January 1st, and so I have a question for server setup and such. Facebook has separate domain names/servers for their photos (and I don't know what else), so I would assume that by doing this it would help spread the server loads out. So I am wondering if it would make a very big difference in speed if I had my main server for basically everything, but had another server and such that the photos would be stored on and access them the same way that facebook does.

  Read the article

< Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >