Search Results

Search found 13325 results on 533 pages for 'domain transferring'.

Page 296/533 | < Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >

• File transfer problems through VPN when Cisco IPS is enabled

  - by Richard West

  We have a Cisco ASA 5510 firewall with the IPS module installed. We have a customer that we must connect to via VPN to their network to exchange files via FTP. We use the Cisco VPN client (version 5.0.01.0600) on our local workstations, which are behind the firewall and subject to the IPS. The VPN client is successful in connecting to the remote site. However when we start the FTP file transfer we are able to upload only 150K to 200K of data, then everything stops. A minute later the VPN session is dropped. I think I have isolated this to an IPS issue by temporarily disabling the Service Policy on the ASA for the IPS with the following command: access-list IPS line 1 extended permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 inactive After this command was issued I then established the VPN to the remote site and was successful in transferring the entire file. While still connected to the VPN and FTP session I issued the command to enable the IPS: access-list IPS line 1 extended permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 The file transfer was tried again and was once again successful so I closed the FTP session and reopened it, while keeping the same VPN session open. This file transfer was also successful. This told me that nothing with the FTP programs was being filtered or causing the problem. Furthermore, we use FTP to exchange files with many sites everyday without issue. I then disconnected the original VPN session, which was established when the access-list was inactive, and reconnected the VPN session, now with the access-list active. After starting the FTP transfer the file stopped after 150K. To me this seems like the IPS is blocking, or somehow interfering with the initial VPN setup to the remote site. This only started happening last week after the latest IPS signature updates were applied (sig version 407.0). Our previous sig version was 95 days old becuase the system was not auto updating itself. Any ideas on what could be causing this problem?

  Read the article

• Intel Wireless 4965AGN not achieving N throughput when connected to an Airport Express N network

  - by BenA

  I have an Intel Wireless WiFi Link 4965AGN adaptor in my laptop (HP Pavillion dv2000 series) which is connecting to a 5Ghz-only 802.11n network provided by an Apple Airport Express. The network is using WPA2 encryption. My desktop is also connected the Airport, via a Linksys WUSB600N USB adaptor. Both are running with the latest drivers, and the Airport is running the latest firmware. The Airport is also configured to use wide channels. The problem I have is that I never get throughput above 4MB/s when transferring files between the two machines. Even a pessimistic calculation shows a 270Mbps network as being capable of transfer rates at well above 10MB/s. I'm pretty sure I've isolated the issue to being the Intel adaptor, as wiring the desktop to the AP, and using the Linksys adaptor on the laptop immediately yielded speeds limited by the 100MB/s ethernet connection. I know that 802.11n is still a draft standard, and so mixing kit from different manufacturers can easily lead to poor results, but I was just wondering if anybody else out there has had success with this Intel adaptor on an N network? Or even better, connecting it to an Airport Express? Can anybody give me any advice on how to troubleshoot this issue? I should also mention that the Airport Express doesn't allow you to manually specify channels when running in N mode, and that I've been able to rule out interference from other Wireless LANs by scanning. There aren't any other 5GHz networks in my area. All ideas welcome! Update: A while later, I've just updated to the most recent drivers for both the Intel chip in the laptop, and the USB adaptor. Unfortunately this hasn't improved things :(. If anybody has any advice it would be be gratefully received.

  Read the article

• WMI/VBS/HTML System Information Script

  - by Methical

  Hey guys; havin' a problem with this code here; can't seem to work out whats goin' wrong with it. All other variables seem to print fine in the HTML ouput; but I get an error that relates to the cputype variable. I get the following error C:\Users\Methical\Desktop\sysinfo.vbs(235,1) Microsoft VBScript runtime error: Invalid procedure call or argument I think it has somethin' to do with this line here fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>CPU</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & cputype & "</i></td></tr>" If i delete this line; the script compiles and outputs with no errors. Here is the full code below Dim strComputer, objWMIService, propValue, objItem Dim strUserName, strPassword, colItems, SWBemlocator ' This section querries for the workstation to be scanned. UserName = "" Password = "" strComputer = "127.1.1.1" ImgDir = "C:\Scripts\images\" 'Sets up the connections and opjects to be used throughout the script. Set SWBemlocator = CreateObject("WbemScripting.SWbemLocator") Set objWMIService = SWBemlocator.ConnectServer(,"root\CIMV2",strUserName,strPassword) 'This determines the current date and time of the PC being scanned. Set colItems = objWMIService.ExecQuery("SELECT * FROM Win32_LocalTime", "WQL", wbemFlagReturnImmediately + wbemFlagForwardOnly) For Each objItem in colItems If objItem.Minute < 10 Then theMinutes = "0" & objItem.Minute Else theMinutes = objItem.Minute End If If objItem.Second < 10 Then theSeconds = "0" & objItem.Second Else theSeconds = objItem.Second End If DateTime = objItem.Month & "/" & objItem.Day & "/" & objItem.Year & " - " & objItem.Hour & ":" & theMinutes & ":" & theSeconds Next 'Gets some ingomation about the Operating System including Service Pack level. Set colItems = objWMIService.ExecQuery("Select * from Win32_OperatingSystem",,48) For Each objItem in colItems WKID = objItem.CSName WKOS = objItem.Caption CSD = objItem.CSDVersion Architecture = objItem.OSArchitecture SysDir = objItem.SystemDirectory SysDrive = objItem.SystemDrive WinDir = objItem.WindowsDirectory ServicePack = objItem.ServicePackMajorVersion & "." & objItem.ServicePackMinorVersion Next 'This section returns the Time Zone Set colItems = objWMIService.ExecQuery("Select * from Win32_TimeZone") For Each objItem in colItems Zone = objItem.Description Next 'This section displays the Shadow Storage information Set colItems = objWMIService.ExecQuery("Select * from Win32_ShadowStorage") For Each objItem in colItems Allocated = int((objItem.AllocatedSpace/1024)/1024+1) UsedSpace = int((objItem.UsedSpace/1024)/1024+1) MaxSpace = int((objItem.MaxSpace/1024)/1024+1) Next 'This section returns the InstallDate of the OS Set objSWbemDateTime = _ CreateObject("WbemScripting.SWbemDateTime") Set colOperatingSystems = _ objWMIService.ExecQuery _ ("Select * from Win32_OperatingSystem") For Each objOperatingSystem _ in colOperatingSystems objSWbemDateTime.Value = _ objOperatingSystem.InstallDate InstallDate = _ objSWbemDateTime.GetVarDate(False) Next 'This section returns the Video card and current resolution. Set colItems = objWMIService.ExecQuery("Select * from Win32_DisplayConfiguration",,48) For Each objItem in colItems VideoCard = objItem.DeviceName Resolution = objItem.PelsWidth & " x " & objItem.PelsHeight & " x " & objItem.BitsPerPel & " bits" Next 'This section returns the Video card memory. Set objWMIService = GetObject("winmgmts:root\cimv2") Set colItems = objWMIService.ExecQuery ("Select * from Win32_VideoController") For Each objItem in colItems VideoMemory = objItem.AdapterRAM/1024/1024 Next 'This returns various system information including current logged on user, domain, memory, manufacture and model. Set colItems = objWMIService.ExecQuery("Select * from Win32_ComputerSystem",,48) For Each objItem in colItems UserName = objItem.UserName Domain = objItem.Domain TotalMemory = int((objItem.TotalPhysicalMemory/1024)/1024+1) Manufacturer = objItem.Manufacturer Model = objItem.Model SysType = objItem.SystemType Next 'This determines the total hard drive space and free hard drive space. Set colItems = objWMIService.ExecQuery("Select * from Win32_LogicalDisk Where Name='C:'",,48) For Each objItem in colItems FreeHDSpace = Fix(((objItem.FreeSpace/1024)/1024)/1024) TotalHDSpace = Fix(((objItem.Size/1024)/1024)/1024) Next 'This section returns the default printer and printer port. Set colItems = objWMIService.ExecQuery("SELECT * FROM Win32_Printer where Default=True", "WQL", wbemFlagReturnImmediately + wbemFlagForwardOnly) For Each objItem in colItems Printer = objItem.Name PortName = objItem.PortName Next 'This returns the CPU information. Set colItems = objWMIService.ExecQuery("SELECT * FROM Win32_Processor", "WQL", wbemFlagReturnImmediately + wbemFlagForwardOnly) For Each objItem in colItems CPUDesc = LTrim(objItem.Name) Next '// CPU Info For each objCPU in GetObject("winmgmts:{impersonationLevel=impersonate}\\" & strComputer & "\root\cimv2").InstancesOf("Win32_Processor") Select Case objCPU.Family Case 2 cputype = "Unknown" Case 11 cputype = "Pentium brand" Case 12 cputype = "Pentium Pro" Case 13 cputype = "Pentium II" Case 14 cputype = "Pentium processor with MMX technology" Case 15 cputype = "Celeron " Case 16 cputype = "Pentium II Xeon" Case 17 cputype = "Pentium III" Case 28 cputype = "AMD Athlon Processor Family" Case 29 cputype = "AMD Duron Processor" Case 30 cputype = "AMD2900 Family" Case 31 cputype = "K6-2+" Case 130 cputype = "Itanium Processor" Case 176 cputype = "Pentium III Xeon" Case 177 cputype = "Pentium III Processor with Intel SpeedStep Technology" Case 178 cputype = "Pentium 4" Case 179 cputype = "Intel Xeon" Case 181 cputype = "Intel Xeon processor MP" Case 182 cputype = "AMD AthlonXP Family" Case 183 cputype = "AMD AthlonMP Family" Case 184 cputype = "Intel Itanium 2" Case 185 cputype = "AMD Opteron? Family" End Select Next 'This returns the current uptime (time since last reboot) of the system. Set colOperatingSystems = objWMIService.ExecQuery ("Select * from Win32_OperatingSystem") For Each objOS in colOperatingSystems dtmBootup = objOS.LastBootUpTime dtmLastBootupTime = WMIDateStringToDate(dtmBootup) dtmSystemUptime = DateDiff("h", dtmLastBootUpTime, Now) Uptime = dtmSystemUptime Next Function WMIDateStringToDate(dtmBootup) WMIDateStringToDate = CDate(Mid(dtmBootup, 5, 2) & "/" & Mid(dtmBootup, 7, 2) & "/" & Left(dtmBootup, 4) & " " & Mid (dtmBootup, 9, 2) & ":" & Mid(dtmBootup, 11, 2) & ":" & Mid(dtmBootup,13, 2)) End Function dim objFSO Set objFSO = CreateObject("Scripting.FileSystemObject") ' -- The heart of the create file script ----------------------- ' -- Creates the file using the value of strFile on Line 11 ' -------------------------------------------------------------- Set fileOutput = objFSO.CreateTextFile( "x.html", true ) 'Set fileOutput = objExplorer.Document 'This is the code for the web page to be displayed. fileOutput.WriteLine "<html>" fileOutput.WriteLine " <head>" fileOutput.WriteLine " <title>System Information for '" & WKID & "' </title>" fileOutput.WriteLine " </head>" fileOutput.WriteLine " <body bgcolor='#FFFFFF' text='#000000' link='#0000FF' vlink='000099' alink='#00FF00'>" fileOutput.WriteLine " <center>" fileOutput.WriteLine " <h1>System Information for " & WKID & "</h1>" fileOutput.WriteLine " <table border='0' cellspacing='1' cellpadding='1' width='95%'>" fileOutput.WriteLine " <tr><td background='" & ImgDir & "blue_spacer.gif'>" fileOutput.WriteLine " <table border='0' cellspacing='0' cellpadding='0' width='100%'>" fileOutput.WriteLine " <tr><td>" fileOutput.WriteLine " <table border='0' cellspacing='0' cellpadding='0' width='100%'>" fileOutput.WriteLine " <tr>" fileOutput.WriteLine " <td width='5%' align='left' valign='middle' background='" & ImgDir & "blue_spacer.gif'><img src='" & ImgDir & "write.gif'></td>" fileOutput.WriteLine " <td width='95%' align='left' valign='middle' background='" & ImgDir & "blue_spacer.gif'> <font color='#FFFFFF' size='5'>WKInfo - </font><font color='#FFFFFF' size='3'>General information on the Workstation.</font></td>" fileOutput.WriteLine " </tr>" fileOutput.WriteLine " <tr><td colspan='2' bgcolor='#FFFFFF'>" fileOutput.WriteLine " <TABLE width='100%' cellspacing='0' cellpadding='2' border='1' bordercolor='#c0c0c0' bordercolordark='#ffffff' bordercolorlight='#c0c0c0'>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>Date and Time</h3></b></TD></TR>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Date/Time</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & DateTime & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>System Uptime</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Uptime & " hours</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Time Zone</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Zone & " </i></td></tr>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>General Computer Information</h3></b></TD></TR>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Manufacturer</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Manufacturer & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Model</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Model & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>System Based</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & SysType & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Operating System</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & WKOS & " " & CSD & " " & Architecture & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Operating System Install Date</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & InstallDate & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>UserName</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & UserName & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Workstation Name</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & WKID & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Domain</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Domain & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>System Drive</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & SysDrive & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>System Directory</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & SysDir & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Windows Directory</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & WinDir & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>ShadowStorage Allocated Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Allocated & " MB</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>ShadowStorage Used Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & UsedSpace & " MB</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>ShadowStorage Max Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & MaxSpace & " MB</i></td></tr>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>General Hardware Information</h3></b></TD></TR>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>CPU</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & cputype & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Memory</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & TotalMemory & " MB</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Total HDD Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & TotalHDSpace & " GB</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Free HDD Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & FreeHDSpace & " GB</i></td></tr>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>General Video Card Information</h3></b></TD></TR>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Video Card</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & VideoCard & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Resolution</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Resolution & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Memory</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & VideoMemory & " MB</i></td></tr>" 'This section lists all the current services and their status. fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>Current Service Information</h3></b></TD></TR>" fileOutput.WriteLine " <tr><td colspan='2' bgcolor='#f0f0f0'>" fileOutput.WriteLine " <TABLE width='100%' cellspacing='0' cellpadding='2' border='1' bordercolor='#c0c0c0' bordercolordark='#ffffff' bordercolorlight='#c0c0c0'>" fileOutput.WriteLine " <TR><TD width='70%' align='center' bgcolor='#e0e0e0'><b>Service Name</b></td><TD width='30%' align='center' bgcolor='#e0e0e0'><b>Service State</b></td><tr>" Set colRunningServices = objWMIService.ExecQuery("Select * from Win32_Service") For Each objService in colRunningServices fileOutput.WriteLine " <TR><TD align='left' bgcolor='#f0f0f0'>" & objService.DisplayName & "</TD><td bgcolor=#f0f0f0 align=center><i>" & objService.State & "</i></td></tr>" wscript.echo " <TR><TD align='left' bgcolor='#f0f0f0'>" & objService.DisplayName & "</TD><td bgcolor=#f0f0f0 align=center><i>" & objService.State & "</i></td></tr>" Next fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" 'This section lists all the current running processes and some information. fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>Current Process Information</h3></b></TD></TR>" fileOutput.WriteLine " <tr><td colspan='2' bgcolor='#f0f0f0'>" fileOutput.WriteLine " <TABLE width='100%' cellspacing='0' cellpadding='2' border='1' bordercolor='#c0c0c0' bordercolordark='#ffffff' bordercolorlight='#c0c0c0'>" fileOutput.WriteLine " <TR><TD width='10%' align='center' bgcolor='#e0e0e0'><b>PID</b></td><TD width='35%' align='center' bgcolor='#e0e0e0'><b>Process Name</b></td><TD width='40%' align='center' bgcolor='#e0e0e0'><b>Owner</b></td><TD width='15%' align='center' bgcolor='#e0e0e0'><b>Memory</b></td></tr>" Set colProcessList = objWMIService.ExecQuery("Select * from Win32_Process") For Each objProcess in colProcessList colProperties = objProcess.GetOwner(strNameOfUser,strUserDomain) fileOutput.WriteLine " <TR><TD align='center' bgcolor='#f0f0f0'>" & objProcess.Handle & "</td><TD align='center' bgcolor='#f0f0f0'>" & objProcess.Name & "</td><TD align='center' bgcolor='#f0f0f0'>" & strUserDomain & "\" & strNameOfUser & "</td><TD align='center' bgcolor='#f0f0f0'>" & objProcess.WorkingSetSize/1024 & " kb</td><tr>" Next fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" 'This section lists all the currently installed software on the machine. fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><i>Installed Software</i></b></TD></TR>" fileOutput.WriteLine " <tr><td colspan='2' bgcolor='#f0f0f0'>" Set colSoftware = objWMIService.ExecQuery ("Select * from Win32_Product") For Each objSoftware in colSoftware fileOutput.WriteLine" <TABLE width='100%' cellspacing='0' cellpadding='2' border='1' bordercolor='#c0c0c0' bordercolordark='#ffffff' bordercolorlight='#c0c0c0'>" fileOutput.WriteLine" <tr><td width=30% align=center bgcolor='#e0e0e0'><b>Name</b></td><td width=30% align=center bgcolor='#e0e0e0'><b>Vendor</b></td><td width=30% align=center bgcolor='#e0e0e0'><b>Version</b></td></tr>" fileOutput.WriteLine" <tr><td align=center bgcolor=#f0f0f0>" & objSoftware.Name & "</td><td align=center bgcolor=#f0f0f0>" & objSoftware.Vendor & "</td><td align=center bgcolor=#f0f0f0>" & objSoftware.Version & "</td></tr>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine" </table>" Next fileOutput.WriteLine " </td></tr>" fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" fileOutput.WriteLine " </table>" fileOutput.WriteLine " <p><small></small></p>" fileOutput.WriteLine " </center>" fileOutput.WriteLine " </body>" fileOutput.WriteLine "<html>" fileOutput.close WScript.Quit

  Read the article

• Chunking large rsync transfers?

  - by Gabe Martin-Dempesy

  We use rsync to update a mirror of our primary file server to an off-site colocated backup server. One of the issues we currently have is that our file server has 1TB of mostly smaller files (in the 10-100kb range), and when we're transferring this much data, we often end up with the connection being dropped several hours into the transfer. Rsync doesn't have a resume/retry feature that simply reconnects to the server to pickup where it left off -- you need to go through the file comparison process, which ends up being very length with the amount of files we have. The solution that's recommended to get around is to split up your large rsync transfer into a series of smaller transfers. I've figured the best way to do this is by first letter of the top-level directory names, which doesn't give us a perfectly even distribution, but is good enough. I'd like to confirm if my methodology for doing this is sane, or if there's a more simple way to accomplish the goal. To do this, I iterate through A-Z, a-z, 0-9 to pick a one character $prefix. Initially I was thinking of just running rsync -av --delete --delete-excluded --exclude "*.mp3" "src/$prefix*" dest/ (--exclude "*.mp3" is just an example, as we have a more lengthy exclude list for removing things like temporary files) The problem with this is that any top-level directories in dest/ that are no longer present present on src will not get picked up by --delete. To get around this, I'm instead trying the following: rsync \ --filter 'S /$prefix*' \ --filter 'R /$prefix*' \ --filter 'H /*' \ --filter 'P /*' \ -av --delete --delete-excluded --exclude "*.mp3" src/ dest/ I'm using the show and hide over include and exclude, because otherwise the --delete-excluded will delete anything that doesn't match $prefix. Is this the most effective way of splitting the rsync into smaller chunks? Is there a more effective tool, or a flag that I've missed, that might make this more simple?

  Read the article

• Making Sense of ASP.NET Paths

  - by Renso

  Making Sense of ASP.NET Paths ASP.Net includes quite a plethora of properties to retrieve path information about the current request, control and application. There's a ton of information available about paths on the Request object, some of it appearing to overlap and some of it buried several levels down, and it can be confusing to find just the right path that you are looking for. To keep things straight I thought it a good idea to summarize the path options along with descriptions and example paths. I wrote a post about this a long time ago in 2004 and I find myself frequently going back to that page to quickly figure out which path I’m looking for in processing the current URL. Apparently a lot of people must be doing the same, because the original post is the second most visited even to this date on this blog to the tune of nearly 500 hits per day. So, I decided to update and expand a bit on the original post with a little more information and clarification based on the original comments. Request Object Paths Available Here's a list of the Path related properties on the Request object (and the Page object). Assume a path like http://www.west-wind.com/webstore/admin/paths.aspx for the paths below where webstore is the name of the virtual. Request Property Description and Value ApplicationPath Returns the web root-relative logical path to the virtual root of this app. /webstore/ PhysicalApplicationPath Returns local file system path of the virtual root for this app. c:\inetpub\wwwroot\webstore PhysicalPath Returns the local file system path to the current script or path. c:\inetpub\wwwroot\webstore\admin\paths.aspx Path FilePath CurrentExecutionFilePath All of these return the full root relative logical path to the script page including path and scriptname. CurrentExcecutionFilePath will return the ‘current’ request path after a Transfer/Execute call while FilePath will always return the original request’s path. /webstore/admin/paths.aspx AppRelativeCurrentExecutionFilePath Returns an ASP.NET root relative virtual path to the script or path for the current request. If in  a Transfer/Execute call the transferred Path is returned. ~/admin/paths.aspx PathInfo Returns any extra path following the script name. If no extra path is provided returns the root-relative path (returns text in red below). string.Empty if no PathInfo is available. /webstore/admin/paths.aspx/ExtraPathInfo RawUrl Returns the full root relative URL including querystring and extra path as a string. /webstore/admin/paths.aspx?sku=wwhelp40 Url Returns a fully qualified URL including querystring and extra path. Note this is a Uri instance rather than string. http://www.west-wind.com/webstore/admin/paths.aspx?sku=wwhelp40 UrlReferrer The fully qualified URL of the page that sent the request. This is also a Uri instance and this value is null if the page was directly accessed by typing into the address bar or using an HttpClient based Referrer client Http header. http://www.west-wind.com/webstore/default.aspx?Info Control.TemplateSourceDirectory Returns the logical path to the folder of the page, master or user control on which it is called. This is useful if you need to know the path only to a Page or control from within the control. For non-file controls this returns the Page path. /webstore/admin/ As you can see there’s a ton of information available there for each of the three common path formats: Physical Path is an OS type path that points to a path or file on disk. Logical Path is a Web path that is relative to the Web server’s root. It includes the virtual plus the application relative path. ~/ (Root-relative) Path is an ASP.NET specific path that includes ~/ to indicate the virtual root Web path. ASP.NET can convert virtual paths into either logical paths using Control.ResolveUrl(), or physical paths using Server.MapPath(). Root relative paths are useful for specifying portable URLs that don’t rely on relative directory structures and very useful from within control or component code. You should be able to get any necessary format from ASP.NET from just about any path or script using these mechanisms. ~/ Root Relative Paths and ResolveUrl() and ResolveClientUrl() ASP.NET supports root-relative virtual path syntax in most of its URL properties in Web Forms. So you can easily specify a root relative path in a control rather than a location relative path: <asp:Image runat="server" ID="imgHelp" ImageUrl="~/images/help.gif" /> ASP.NET internally resolves this URL by using ResolveUrl("~/images/help.gif") to arrive at the root-relative URL of /webstore/images/help.gif which uses the Request.ApplicationPath as the basepath to replace the ~. By convention any custom Web controls also should use ResolveUrl() on URL properties to provide the same functionality. In your own code you can use Page.ResolveUrl() or Control.ResolveUrl() to accomplish the same thing: string imgPath = this.ResolveUrl("~/images/help.gif"); imgHelp.ImageUrl = imgPath; Unfortunately ResolveUrl() is limited to WebForm pages, so if you’re in an HttpHandler or Module it’s not available. ASP.NET Mvc also has it’s own more generic version of ResolveUrl in Url.Decode: <script src="<%= Url.Content("~/scripts/new.js") %>" type="text/javascript"></script> which is part of the UrlHelper class. In ASP.NET MVC the above sort of syntax is actually even more crucial than in WebForms due to the fact that views are not referencing specific pages but rather are often path based which can lead to various variations on how a particular view is referenced. In a Module or Handler code Control.ResolveUrl() unfortunately is not available which in retrospect seems like an odd design choice – URL resolution really should happen on a Request basis not as part of the Page framework. Luckily you can also rely on the static VirtualPathUtility class: string path = VirtualPathUtility.ToAbsolute("~/admin/paths.aspx"); VirtualPathUtility also many other quite useful methods for dealing with paths and converting between the various kinds of paths supported. One thing to watch out for is that ToAbsolute() will throw an exception if a query string is provided and doesn’t work on fully qualified URLs. I wrote about this topic with a custom solution that works fully qualified URLs and query strings here (check comments for some interesting discussions too). Similar to ResolveUrl() is ResolveClientUrl() which creates a fully qualified HTTP path that includes the protocol and domain name. It’s rare that this full resolution is needed but can be useful in some scenarios. Mapping Virtual Paths to Physical Paths with Server.MapPath() If you need to map root relative or current folder relative URLs to physical URLs or you can use HttpContext.Current.Server.MapPath(). Inside of a Page you can do the following: string physicalPath = Server.MapPath("~/scripts/ww.jquery.js")); MapPath is pretty flexible and it understands both ASP.NET style virtual paths as well as plain relative paths, so the following also works. string physicalPath = Server.MapPath("scripts/silverlight.js"); as well as dot relative syntax: string physicalPath = Server.MapPath("../scripts/jquery.js"); Once you have the physical path you can perform standard System.IO Path and File operations on the file. Remember with physical paths and IO or copy operations you need to make sure you have permissions to access files and folders based on the Web server user account that is active (NETWORK SERVICE, ASPNET typically). Note the Server.MapPath will not map up beyond the virtual root of the application for security reasons. Server and Host Information Between these settings you can get all the information you may need to figure out where you are at and to build new Url if necessary. If you need to build a URL completely from scratch you can get access to information about the server you are accessing: Server Variable Function and Example SERVER_NAME The of the domain or IP Address wwww.west-wind.com or 127.0.0.1 SERVER_PORT The port that the request runs under. 80 SERVER_PORT_SECURE Determines whether https: was used. 0 or 1 APPL_MD_PATH ADSI DirectoryServices path to the virtual root directory. Note that LM typically doesn’t work for ADSI access so you should replace that with LOCALHOST or the machine’s NetBios name. /LM/W3SVC/1/ROOT/webstore Request.Url and Uri Parsing If you still need more control over the current request URL or  you need to create new URLs from an existing one, the current Request.Url Uri property offers a lot of control. Using the Uri class and UriBuilder makes it easy to retrieve parts of a URL and create new URLs based on existing URL. The UriBuilder class is the preferred way to create URLs – much preferable over creating URIs via string concatenation. Uri Property Function Scheme The URL scheme or protocol prefix. http or https Port The port if specifically specified. DnsSafeHost The domain name or local host NetBios machine name www.west-wind.com or rasnote LocalPath The full path of the URL including script name and extra PathInfo. /webstore/admin/paths.aspx Query The query string if any ?id=1 The Uri class itself is great for retrieving Uri parts, but most of the properties are read only if you need to modify a URL in order to change it you can use the UriBuilder class to load up an existing URL and modify it to create a new one. Here are a few common operations I’ve needed to do to get specific URLs: Convert the Request URL to an SSL/HTTPS link For example to take the current request URL and converted  it to a secure URL can be done like this: UriBuilder build = new UriBuilder(Request.Url); build.Scheme = "https"; build.Port = -1; // don't inject portUri newUri = build.Uri; string newUrl = build.ToString(); Retrieve the fully qualified URL without a QueryString AFAIK, there’s no native routine to retrieve the current request URL without the query string. It’s easy to do with UriBuilder however: UriBuilder builder = newUriBuilder(Request.Url); builder.Query = ""; stringlogicalPathWithoutQuery = builder.ToString();

  Read the article

• Cloning a WebCenter Portal Managed Server

  - by Maiko Rocha

  I had to run some tests on a WebCenter Portal application deployed in a cluster. I've got a development VM with WebCenter PS4 (this also works on PS5) and I was trying to figure out how could I easily add a new managed server to my single-node domain, and make it a cluster. Creating the machine and cluster are a piece of cake, you can do it pretty quick through WLS Console. Now, you'd guess that using the clone option on WLS Console would do the magic of cloning an existing instance, right? Well, it does, but all you get is an "empty" managed server: with no target libraries.  It was a good surprise to find that WebCenter provides a way of cloning an existing WebCenter Portal managed server through a simple WLST command: cloneWebCenterManagedServer  This is a screenshot of my starting point. I want to clone WC_CustomPortal managed server: These are the steps to clone my WC_CustomPortal managed server: 1. In the command line, invoke WLST. It should be on <ORACLE_HOME_for_component>/common/bin/wlst.sh. In my case, it is ./product/Middleware/WebCenterPortal/common/bin/wlst.sh 2. Connect to the Admin Server:  connect ('<wls_admin_username>','<password>','t3://<server>:<port>') 3. Execute the following command: wls:/webcenter/serverConfig> cloneWebCenterManagedServer(baseManagedServer='WC_CustomPortal', newManagedServer='WC_CustomPortal2', newManagedServerPort=8893, verbose=1) I've turned on verbose output on purpose so I could see what the script was doing while executing. This is the output:  [...] Creating the Managed Server "WC_CustomPortal2" MBean type Server with name WC_CustomPortal2 has been created successfully. Targeting the library "oracle.bi.adf.model.slib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.bi.adf.view.slib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.bi.adf.webcenter.slib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.wsm.seedpolicies#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.jsp.next#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.dconfig-infra#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "orai18n-adf#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.adf.dconfigbeans#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.pwdgen#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.jrf.system.filter" to the Managed Server "WC_CustomPortal2" Targeting the library "adf.oracle.domain#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "adf.oracle.businesseditor#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.adf.management#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "adf.oracle.domain.webapp#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "jsf#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "jstl#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "UIX#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "ohw-rcf#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "ohw-uix#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.adf.desktopintegration.model#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.adf.desktopintegration#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.bi.jbips#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.bi.composer#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.skin#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.composer#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.framework.core#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.sdp.client#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.soa.workflow.wc#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.soa.worklist.webapp#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.ucm.ridc.app-lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "p13n-app-lib-base#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "p13n-core-web-lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "jaxrs-framework-web-lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "jersey-web-lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "wcps-util-app-lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "wcps-services-client-web-lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "content-app-lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "content-web-lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.framework#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.framework.view#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.forum.dependency#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.jive.dependency#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.spaces.fwk#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the library "oracle.webcenter.activitygraph.lib#[email protected]" to the Managed Server "WC_CustomPortal2" Targeting the datasource "mds-CustomPortalDS" to the Managed Server "WC_CustomPortal2" Targeting the datasource "WebCenter-CustomPortalDS" to the Managed Server "WC_CustomPortal2" Targeting the datasource "Activities-CustomPortalDS" to the Managed Server "WC_CustomPortal2" Targeting the application "wsil-wls" to the Managed Server "WC_CustomPortal2" Targeting the application "DMS Application#11.1.1.1.0" to the Managed Server "WC_CustomPortal2" Targeting the application "ViewHandlerOverride_webapp1#V2.0" to the Managed Server "WC_CustomPortal2" Targeting the application "ViewHandlerOverride_application1#V2.0" to the Managed Server "WC_CustomPortal2" Targeting the startup class "JRF Startup Class" to the Managed Server "WC_CustomPortal2" Targeting the startup class "JPS Startup Class" to the Managed Server "WC_CustomPortal2" Targeting the startup class "ODL-Startup" to the Managed Server "WC_CustomPortal2" Targeting the startup class "Audit Loader Startup Class" to the Managed Server "WC_CustomPortal2" Targeting the startup class "AWT Application Context Startup Class" to the Managed Server "WC_CustomPortal2" Targeting the startup class "JMX Framework Startup Class" to the Managed Server "WC_CustomPortal2" Targeting the startup class "Web Services Startup Class" to the Managed Server "WC_CustomPortal2" Targeting the startup class "JOC-Startup" to the Managed Server "WC_CustomPortal2" Targeting the startup class "DMS-Startup" to the Managed Server "WC_CustomPortal2" Targeting the shutdown class "JOC-Shutdown" to the Managed Server "WC_CustomPortal2" Targeting the shutdown class "DMSShutdown" to the Managed Server "WC_CustomPortal2" Validating changes ... Validated the changes successfully [...] And this is the newly created WC_CustomPortal2 managed server showing up on Weblogic console:  Here is the full reference to WebCenter Portal Custom WLST Commands. Special thanks to Todd Vender for pointing this one out! :-)

  Read the article

• NHibernate Conventions

  - by Ricardo Peres

  Introduction It seems that nowadays everyone loves conventions! Not the ones that you go to, but the ones that you use, that is! It just happens that NHibernate also supports conventions, and we’ll see exactly how. Conventions in NHibernate are supported in two ways: Naming of tables and columns when not explicitly indicated in the mappings; Full domain mapping. Naming of Tables and Columns Since always NHibernate has supported the concept of a naming strategy. A naming strategy in NHibernate converts class and property names to table and column names and vice-versa, when a name is not explicitly supplied. In concrete, it must be a realization of the NHibernate.Cfg.INamingStrategy interface, of which NHibernate includes two implementations: DefaultNamingStrategy: the default implementation, where each column and table are mapped to identically named properties and classes, for example, “MyEntity” will translate to “MyEntity”; ImprovedNamingStrategy: underscores (_) are used to separate Pascal-cased fragments, for example, entity “MyEntity” will be mapped to a “my_entity” table. The naming strategy can be defined at configuration level (the Configuration instance) by calling the SetNamingStrategy method: 1: cfg.SetNamingStrategy(ImprovedNamingStrategy.Instance); Both the DefaultNamingStrategy and the ImprovedNamingStrategy classes offer singleton instances in the form of Instance static fields. DefaultNamingStrategy is the one NHibernate uses, if you don’t specify one. Domain Mapping In mapping by code, we have the choice of relying on conventions to do the mapping automatically. This means a class will inspect our classes and decide how they will relate to the database objects. The class that handles conventions is NHibernate.Mapping.ByCode.ConventionModelMapper, a specialization of the base by code mapper, NHibernate.Mapping.ByCode.ModelMapper. The ModelMapper relies on an internal SimpleModelInspector to help it decide what and how to map, but the mapper lets you override its decisions.  You apply code conventions like this: 1: //pick the types that you want to map 2: IEnumerable<Type> types = Assembly.GetExecutingAssembly().GetExportedTypes(); 3:  4: //conventions based mapper 5: ConventionModelMapper mapper = new ConventionModelMapper(); 6:  7: HbmMapping mapping = mapper.CompileMappingFor(types); 8:  9: //the one and only configuration instance 10: Configuration cfg = ...; 11: cfg.AddMapping(mapping); This is a very simple example, it lacks, at least, the id generation strategy, which you can add by adding an event handler like this: 1: mapper.BeforeMapClass += (IModelInspector modelInspector, Type type, IClassAttributesMapper classCustomizer) => 2: { 3: classCustomizer.Id(x => 4: { 5: //set the hilo generator 6: x.Generator(Generators.HighLow); 7: }); 8: }; The mapper will fire events like this whenever it needs to get information about what to do. And basically this is all it takes to automatically map your domain! It will correctly configure many-to-one and one-to-many relations, choosing bags or sets depending on your collections, will get the table and column names from the naming strategy we saw earlier and will apply the usual defaults to all properties, such as laziness and fetch mode. However, there is at least one thing missing: many-to-many relations. The conventional mapper doesn’t know how to find and configure them, which is a pity, but, alas, not difficult to overcome. To start, for my projects, I have this rule: each entity exposes a public property of type ISet<T> where T is, of course, the type of the other endpoint entity. Extensible as it is, NHibernate lets me implement this very easily: 1: mapper.IsOneToMany((MemberInfo member, Boolean isLikely) => 2: { 3: Type sourceType = member.DeclaringType; 4: Type destinationType = member.GetMemberFromDeclaringType().GetPropertyOrFieldType(); 5:  6: //check if the property is of a generic collection type 7: if ((destinationType.IsGenericCollection() == true) && (destinationType.GetGenericArguments().Length == 1)) 8: { 9: Type destinationEntityType = destinationType.GetGenericArguments().Single(); 10:  11: //check if the type of the generic collection property is an entity 12: if (mapper.ModelInspector.IsEntity(destinationEntityType) == true) 13: { 14: //check if there is an equivalent property on the target type that is also a generic collection and points to this entity 15: PropertyInfo collectionInDestinationType = destinationEntityType.GetProperties().Where(x => (x.PropertyType.IsGenericCollection() == true) && (x.PropertyType.GetGenericArguments().Length == 1) && (x.PropertyType.GetGenericArguments().Single() == sourceType)).SingleOrDefault(); 16:  17: if (collectionInDestinationType != null) 18: { 19: return (false); 20: } 21: } 22: } 23:  24: return (true); 25: }); 26:  27: mapper.IsManyToMany((MemberInfo member, Boolean isLikely) => 28: { 29: //a relation is many to many if it isn't one to many 30: Boolean isOneToMany = mapper.ModelInspector.IsOneToMany(member); 31: return (!isOneToMany); 32: }); 33:  34: mapper.BeforeMapManyToMany += (IModelInspector modelInspector, PropertyPath member, IManyToManyMapper collectionRelationManyToManyCustomizer) => 35: { 36: Type destinationEntityType = member.LocalMember.GetPropertyOrFieldType().GetGenericArguments().First(); 37: //set the mapping table column names from each source entity name plus the _Id sufix 38: collectionRelationManyToManyCustomizer.Column(destinationEntityType.Name + "_Id"); 39: }; 40:  41: mapper.BeforeMapSet += (IModelInspector modelInspector, PropertyPath member, ISetPropertiesMapper propertyCustomizer) => 42: { 43: if (modelInspector.IsManyToMany(member.LocalMember) == true) 44: { 45: propertyCustomizer.Key(x => x.Column(member.LocalMember.DeclaringType.Name + "_Id")); 46:  47: Type sourceType = member.LocalMember.DeclaringType; 48: Type destinationType = member.LocalMember.GetPropertyOrFieldType().GetGenericArguments().First(); 49: IEnumerable<String> names = new Type[] { sourceType, destinationType }.Select(x => x.Name).OrderBy(x => x); 50:  51: //set inverse on the relation of the alphabetically first entity name 52: propertyCustomizer.Inverse(sourceType.Name == names.First()); 53: //set mapping table name from the entity names in alphabetical order 54: propertyCustomizer.Table(String.Join("_", names)); 55: } 56: }; We have to understand how the conventions mapper thinks: For each collection of entities found, it will ask the mapper if it is a one-to-many; in our case, if the collection is a generic one that has an entity as its generic parameter, and the generic parameter type has a similar collection, then it is not a one-to-many; Next, the mapper will ask if the collection that it now knows is not a one-to-many is a many-to-many; Before a set is mapped, if it corresponds to a many-to-many, we set its mapping table. Now, this is tricky: because we have no way to maintain state, we sort the names of the two endpoint entities and we combine them with a “_”; for the first alphabetical entity, we set its relation to inverse – remember, on a many-to-many relation, only one endpoint must be marked as inverse; finally, we set the column name as the name of the entity with an “_Id” suffix; Before the many-to-many relation is processed, we set the column name as the name of the other endpoint entity with the “_Id” suffix, as we did for the set. And that’s it. With these rules, NHibernate will now happily find and configure many-to-many relations, as well as all the others. You can wrap this in a new conventions mapper class, so that it is more easily reusable: 1: public class ManyToManyConventionModelMapper : ConventionModelMapper 2: { 3: public ManyToManyConventionModelMapper() 4: { 5: base.IsOneToMany((MemberInfo member, Boolean isLikely) => 6: { 7: return (this.IsOneToMany(member, isLikely)); 8: }); 9:  10: base.IsManyToMany((MemberInfo member, Boolean isLikely) => 11: { 12: return (this.IsManyToMany(member, isLikely)); 13: }); 14:  15: base.BeforeMapManyToMany += this.BeforeMapManyToMany; 16: base.BeforeMapSet += this.BeforeMapSet; 17: } 18:  19: protected virtual Boolean IsManyToMany(MemberInfo member, Boolean isLikely) 20: { 21: //a relation is many to many if it isn't one to many 22: Boolean isOneToMany = this.ModelInspector.IsOneToMany(member); 23: return (!isOneToMany); 24: } 25:  26: protected virtual Boolean IsOneToMany(MemberInfo member, Boolean isLikely) 27: { 28: Type sourceType = member.DeclaringType; 29: Type destinationType = member.GetMemberFromDeclaringType().GetPropertyOrFieldType(); 30:  31: //check if the property is of a generic collection type 32: if ((destinationType.IsGenericCollection() == true) && (destinationType.GetGenericArguments().Length == 1)) 33: { 34: Type destinationEntityType = destinationType.GetGenericArguments().Single(); 35:  36: //check if the type of the generic collection property is an entity 37: if (this.ModelInspector.IsEntity(destinationEntityType) == true) 38: { 39: //check if there is an equivalent property on the target type that is also a generic collection and points to this entity 40: PropertyInfo collectionInDestinationType = destinationEntityType.GetProperties().Where(x => (x.PropertyType.IsGenericCollection() == true) && (x.PropertyType.GetGenericArguments().Length == 1) && (x.PropertyType.GetGenericArguments().Single() == sourceType)).SingleOrDefault(); 41:  42: if (collectionInDestinationType != null) 43: { 44: return (false); 45: } 46: } 47: } 48:  49: return (true); 50: } 51:  52: protected virtual new void BeforeMapManyToMany(IModelInspector modelInspector, PropertyPath member, IManyToManyMapper collectionRelationManyToManyCustomizer) 53: { 54: Type destinationEntityType = member.LocalMember.GetPropertyOrFieldType().GetGenericArguments().First(); 55: //set the mapping table column names from each source entity name plus the _Id sufix 56: collectionRelationManyToManyCustomizer.Column(destinationEntityType.Name + "_Id"); 57: } 58:  59: protected virtual new void BeforeMapSet(IModelInspector modelInspector, PropertyPath member, ISetPropertiesMapper propertyCustomizer) 60: { 61: if (modelInspector.IsManyToMany(member.LocalMember) == true) 62: { 63: propertyCustomizer.Key(x => x.Column(member.LocalMember.DeclaringType.Name + "_Id")); 64:  65: Type sourceType = member.LocalMember.DeclaringType; 66: Type destinationType = member.LocalMember.GetPropertyOrFieldType().GetGenericArguments().First(); 67: IEnumerable<String> names = new Type[] { sourceType, destinationType }.Select(x => x.Name).OrderBy(x => x); 68:  69: //set inverse on the relation of the alphabetically first entity name 70: propertyCustomizer.Inverse(sourceType.Name == names.First()); 71: //set mapping table name from the entity names in alphabetical order 72: propertyCustomizer.Table(String.Join("_", names)); 73: } 74: } 75: } Conclusion Of course, there is much more to mapping than this, I suggest you look at all the events and functions offered by the ModelMapper to see where you can hook for making it behave the way you want. If you need any help, just let me know!

  Read the article

• OFM 11g: Implementing OAM SSO with Forms

  - by olaf.heimburger

  There is some confusion about the integration of OFM 11g Forms with Oracle Access Manager 11g (OAM). Some say this does not work, some say it works, but.... Actually, having implemented it many times I belong to the later group. Here is how. Caveat Before you start installing anything, take a step back and consider your current implementation and what you really need and want to achieve. The current integration of Forms 11g with OAM 11g does not support self-service account creation and password resets from the Forms application. If you really need this, you must use the existing Oracle AS 10.1.4.3 infrastructure. On the other hand, if your user population is pretty stable, you can enjoy the latest Forms 11g with OAM 11g. Assumptions The whole process should be done in one day. I assume that all domains and instances are started during setup, if you need to restart them on demand or purpose, be sure to have proper start/stop scripts, I don't mention them. Preparation It goes without saying, that you always should do a proper backup before you change anything on your production environment. With proper backup, I also mean a tested and verified restore process. If you dared to test it before, do it now. It pays off. Requirements For OAM 11g to work properly you need a LDAP repository. For the integration of Forms 11g you need an Oracle Internet Directory (OID) configured with the Oracle AS SSO LDAP extensions. For better support I usually give the latest version a try, in this case OID 11g is a good choice.During the Installation and Integration steps we use an upgrade wizard that needs the old OID configuration on the same host but in a different ORACLE_HOME. Installation vs Configuration With OFM 11g Oracle introduced a clear separation between Installation of the binaries (the software) and the Configuration of the instances (the runtime). This is really great as you can install all the software and create new instances when needed. In the following we adhere to this scheme and install the software first and then configure the instances later. Installation Steps The Oracle documentation contains all the necessary steps for the installation of all pieces of software. But some hints help to avoid traps and pitfalls. Step 1 The Database Start the installation with the database. It is quite obvious but we need an Oracle database for all the other steps. If you have one at hand, fine. If not, just install at least a Oracle 10.2.0.4 version. This database can be on a different host. Step 2 The Repository Creation Utility The next step should be to run the Repository Creation Utility (RCU). This is a client application that just needs to connect to your database. It can be run on any host that can reach the database and is a Windows or Linux 32-bit machine. When you run it, be sure to install the OID schema and the OAM schema. If you miss one of these, you can run the RCU again to install the missing schema. Step 3 The Foundation With OFM 11g Oracle started to use WebLogic Server 11g (WLS) as its foundation for all OFM 11g installation. We therefore install it first. Depending on your operating system, it might be possible, that no native installer is available. My approach to this dilemma is to use the WLS Generic Installer for all my installations. It does not include a JDK either but if you have both for your platform you are ready to go. Step 3a The JDK To make things interesting, Oracle currently has two JDKs in its portfolio. The Sun JDK and the JRockit JDK. Both are available for a number of platforms. If you are lucky and both are available for your platform, install both in a separate directory (and not one of your ORACLE_HOMEs) each, You can use the later as you like. Step 3b Install WLS for OID and OAM With the JDK installed, we start the generic installer with java -jar wls_generic.jar.STOP! Before you do this, check the version first. It should be 1.6.0_18 or later and not the GCC one (Some Linux distros have it installed by default). To verify the version, issue a java -version command and make sure that the output does not contain the text gcj and the version matches. If this does not work, use an absolute path like /opt/java/jdk1.6.0_23/bin/java to start the installer. The installer allows you to specify a path to install the software into, say /opt/oracle/iam/11.1.1.3 for the OID and OAM installation. We will call this IAM_HOME. Step 4 Install OID Now we are ready to install OID. Start the OID installer (in the Disk1 directory) and just select the installation only step. This will install the software only and does not configure the instance. Use the IAM_HOME as the target directory. Step 5 Install SOA Suite The IAM 11g Suite uses the BPEL component of the SOA Suite 11g for its workflows. This is a pretty closed environment and not to be used for SCA Composites. We install the SOA Suite in $IAM_HOME/soa. The installer only installs the binaries. Configuration will be done later. Step 6 Install OAM Once the installation of OID and SOA is done, we are ready to install the OAM software in the same IAM_HOME. Make sure to install the OAM binaries in a directory different from the one you used during the OID and SOA installation. As before, we only install the software, the instance will be created later. Step 7 Backup the Installation At this point, I normally do a backup (or snapshot in a virtual image) of the installation. Good when you need to go back to this point. Step 8 Configure OID The software is installed and now we need instances to run it. This process is called configuration. For OID use the config.sh found in $IAM_HOME/oid/bin to start the configuration wizard. Normally this runs smoothly. If you encounter some issues check the Oracle Support site for help. This configuration will also start the OID instance. Step 9 Install the Oracle AS SSO Schema Before we install the Forms software we need to install the Oracle AS SSO Schema into the database and OID. This is a rather dangerous procedure, but fully documented in the IAM Installation Guide, Chapter 10. You should finish this in one go, do not reboot your host during the whole procedure. As a precaution, you should make a backup of the OID instance before you start the procedure. Once the backup is ready, read the chapter, including every note, carefully. You can avoid a number of issues by following all the steps and will succeed with a working solution. Step 10 Configure OAM Reached this step? Great. You are ready to create an OAM instance. Use the $IAM_HOME/iam/common/binconfig.sh for this. This will open the WLS Domain Creation Wizard and asks for the libraries to be installed. You should at least select the OAM with Database repository item. The configuration will also start the OAM instance. Step 11 Install WLS for Forms 11g It is quite tempting to install everything in one ORACLE_HOME. Unfortunately this does not work for all OFM packages. Therefore we do another WLS installation in another ORACLE_HOME. The same considerations as in step 3b apply. We call this one FORMS_HOME. Step 12 Install Forms In the FORMS_HOME we now install the binaries for the Forms 11g software. Again, this is a install only step. Configuration starts with the next step. Step 13 Configure Forms To configure Forms 11g we start the Configuration Wizard (config.sh) in FORMS_HOME/bin. This wizard should create a new WebLogic Domain and an OHS instance! Do not extend existing domains or instances! Forms should run in its own instances! When all information is supplied, the wizard will create the domain and instance and starts them automatically.Step 14 Setup your Forms SSO EnvironmentOnce you have implemented and tested your Forms 11g instance, you can configured it for SSO. Yes, this requires the old Oracle AS SSO solution, OIDDAS for creating and assigning users and SSO to setup your partner applications. In this step you should consider to create every user necessary for use within the environment. When done, do not forget to test it. Step 15 Migrate the SSO Repository Since the final goal is to get rid of the old SSO implementation we need to migrate the old SSO repository into the new OID structure. Additionally, this step will also migrate all partner application configurations into OAM 11g. Quite convenient. To do this step, you have to start the upgrade agent (ua or ua.bat or ua.cmd) on the operating system level in $IAM_HOME/bin. Once finished, this wizard will create new osso.conf files for each partner application in $IAM_HOME/upgrade/temp/oam/.Note: At the time of this writing, this step only works if everything is on the same host (ie. OID, OAM, etc.). This restriction might be lifted in later releases. Step 16 Change your OHS sso.conf and shut down OC4J_SECURITY In Step 14 we verified that SSO for our Forms environment works fine. Now, we are shutting the old system done and reconfigure the OHS that acts as the Forms entry point. First we go to the OHS configuration directory and rename the old osso.conf  to osso.conf.10g. Now we change the moduleconf/mod_osso.conf  to point to the new osso.conf file. Copy the new osso.conf  file from $IAM_HOME/upgrade/temp/oam/ to the OHS configuration directory. Restart OHS, test forms by using the same forms links. OAM should now kick in and show the login dialog to ask for your user credentials.Done. Now your Forms environment is successfully integrated with OAM 11g.Enjoy. What's Next? This rather lengthy setup is just the foundation for your growing environment of OAM 11g protections. In the next entry we will show that Forms 11g and ADF Faces 11g can use the same OAM installation and provide real single sign-on. References Nearly everything is documented. Use the documentation! Oracle® Fusion Middleware Installation Guide for Oracle Identity Management 11gR1 Oracle® Fusion Middleware Installation Guide for Oracle Identity Management 11gR1, Chapter 11-14 Oracle® Fusion Middleware Administrator's Guide for Oracle Access Manager 11gR1, Appendix B Oracle® Fusion Middleware Upgrade Guide for Oracle Identity Management 11gR1, Chapter 10   

  Read the article

• How much network latency is "typical" for east - west coast USA?

  - by Jeff Atwood

  At the moment we're trying to decide whether to move our datacenter from the west coast (Corvallis, OR) to the east coast (NY, NY). However, I am seeing some disturbing latency numbers from my location (Berkeley, CA) to the NYC host. Here's a sample result, retrieving a small .png logo file in Google Chrome and using the dev tools to see how long the request takes: Berkeley to NYC server: 215 ms latency, 46ms transfer time, 261ms total Berkeley to Corvallis server: 114ms latency, 41ms transfer time, 155ms total some URLs if you want to try yourself: http://careers.stackoverflow.com/content/cso/img/logo.png (NY, NY) http://serverfault.com/cache/logo.png (Corvallis, OR) It makes sense that Corvallis, OR is geographically closer to Berkeley, CA so I expect the connection to be a bit faster.. but I'm seeing an increase in latency of +100ms when I perform the same test to the NYC server. That seems .. excessive to me. Particularly since the time spent transferring the actual data only went up 10%, yet the latency went up ten times as much! That feels... wrong... to me. I found a few links here that were helpful (through Google no less!) ... http://serverfault.com/questions/63531/does-routing-distance-affect-performance-significantly http://serverfault.com/questions/61719/how-does-geography-affect-network-latency http://serverfault.com/questions/6210/latency-in-internet-connections-from-europe-to-usa ... but nothing authoritative. So, is this normal? It doesn't feel normal. What is the "typical" latency I should expect when moving network packets from the east coast <--> west coast of the USA?

  Read the article

• How can I set up a 404 error page when people access http://ftp.mydomain.com?

  - by Tim B.

  I am a freelance videographer/developer, and part of my job involves transferring large files over FTP to production houses/television stations. While the majority of people in my industry understand the difference between FTP and HTTP, I've experienced several interactions in the past couple months of people who still open Internet Explorer and try to access http://ftp.mydomain.com, receive an error page served by HostGator, and tell me that they cannot access my FTP server. Instead of spending time delivering instructions via e-mail, I'd much prefer to serve up a custom error page in this instance that instructs them how to download and use an FTP client. I tried setting up a sub-domain in Cpanel hoping I could simply drop in an .htaccess file with the error page, but I got this error: ftp.mydomain.com domainadmin-domainexistsglobal I also tried creating a custom error page in PHP which reads the site URL and serves up the custom content only when http://ftp.mydomain.com is accessed. Unfortunately, the error page works for every subdomain except that one. I'm not entirely sure this is even technically possible, which is why I bring it to the good people of StackOverflow to help. Thanks!

  Read the article

• How much network latency is "typical" for east - west coast USA?

  - by Jeff Atwood

  At the moment we're trying to decide whether to move our datacenter from the west coast to the east coast. However, I am seeing some disturbing latency numbers from my west coast location to the east coast. Here's a sample result, retrieving a small .png logo file in Google Chrome and using the dev tools to see how long the request takes: West coast to east coast: 215 ms latency, 46 ms transfer time, 261 ms total West coast to west coast: 114 ms latency, 41 ms transfer time, 155 ms total It makes sense that Corvallis, OR is geographically closer to my location in Berkeley, CA so I expect the connection to be a bit faster.. but I'm seeing an increase in latency of +100ms when I perform the same test to the NYC server. That seems .. excessive to me. Particularly since the time spent transferring the actual data only increased 10%, yet the latency increased 100%! That feels... wrong... to me. I found a few links here that were helpful (through Google no less!) ... Does routing distance affect performance significantly? How does geography affect network latency? Latency in Internet connections from Europe to USA ... but nothing authoritative. So, is this normal? It doesn't feel normal. What is the "typical" latency I should expect when moving network packets from the east coast <--> west coast of the USA?

  Read the article

• File transfer from MP3 player to computer

  - by JP

  I own an old 20GB Creative Zen jukebox (all external screws are gone on it LOL) and I would like to transfer files back to my PC to get them on my new iPod. Problem is, no matter what software I use (WinAMP, Creative Media Source or Windows Media Player), it just stops transferring files on my HD with an error message that says there is no more space on the destination folder. Problem is, there is still 320GB free. I tried lot of things like installing newer driver, latest Zen plug-in for Media Source, latest WinAMP version. Sometimes, it just works and then again, it stops working and I get this non-sense error. Restarting my PC sometime solves the issue by giving me enough time to transfer 10 or 15 more files and then I get the error again and again. Yesterday though I managed to transfer up to 3GB of MP3s on my computer before getting the error. Seems like I'm having a driver issue or a weird behavior from the player and/or the software I'm using. 3 different software can't reproduce the exact same issue by themselves so it must be something related to the driver. I can't find any post of any sort concerning such issue on old forums. Any idea?

  Read the article

• Announcing: Great Improvements to Windows Azure Web Sites

  - by ScottGu

  I’m excited to announce some great improvements to the Windows Azure Web Sites capability we first introduced earlier this summer.  Today’s improvements include: a new low-cost shared mode scaling option, support for custom domains with shared and reserved mode web-sites using both CNAME and A-Records (the later enabling naked domains), continuous deployment support using both CodePlex and GitHub, and FastCGI extensibility.  All of these improvements are now live in production and available to start using immediately. New “Shared” Scaling Tier Windows Azure allows you to deploy and host up to 10 web-sites in a free, shared/multi-tenant hosting environment. You can start out developing and testing web sites at no cost using this free shared mode, and it supports the ability to run web sites that serve up to 165MB/day of content (5GB/month).  All of the capabilities we introduced in June with this free tier remain the same with today’s update. Starting with today’s release, you can now elastically scale up your web-site beyond this capability using a new low-cost “shared” option (which we are introducing today) as well as using a “reserved instance” option (which we’ve supported since June).  Scaling to either of these modes is easy.  Simply click on the “scale” tab of your web-site within the Windows Azure Portal, choose the scaling option you want to use with it, and then click the “save” button.  Changes take only seconds to apply and do not require any code to be changed, nor the app to be redeployed: Below are some more details on the new “shared” option, as well as the existing “reserved” option: Shared Mode With today’s release we are introducing a new low-cost “shared” scaling mode for Windows Azure Web Sites.  A web-site running in shared mode is deployed in a shared/multi-tenant hosting environment.  Unlike the free tier, though, a web-site in shared mode has no quotas/upper-limit around the amount of bandwidth it can serve.  The first 5 GB/month of bandwidth you serve with a shared web-site is free, and then you pay the standard “pay as you go” Windows Azure outbound bandwidth rate for outbound bandwidth above 5 GB. A web-site running in shared mode also now supports the ability to map multiple custom DNS domain names, using both CNAMEs and A-records, to it.  The new A-record support we are introducing with today’s release provides the ability for you to support “naked domains” with your web-sites (e.g. http://microsoft.com in addition to http://www.microsoft.com).  We will also in the future enable SNI based SSL as a built-in feature with shared mode web-sites (this functionality isn’t supported with today’s release – but will be coming later this year to both the shared and reserved tiers). You pay for a shared mode web-site using the standard “pay as you go” model that we support with other features of Windows Azure (meaning no up-front costs, and you pay only for the hours that the feature is enabled).  A web-site running in shared mode costs only 1.3 cents/hr during the preview (so on average $9.36/month). Reserved Instance Mode In addition to running sites in shared mode, we also support scaling them to run within a reserved instance mode.  When running in reserved instance mode your sites are guaranteed to run isolated within your own Small, Medium or Large VM (meaning no other customers run within it).  You can run any number of web-sites within a VM, and there are no quotas on CPU or memory limits. You can run your sites using either a single reserved instance VM, or scale up to have multiple instances of them (e.g. 2 medium sized VMs, etc).  Scaling up or down is easy – just select the “reserved” instance VM within the “scale” tab of the Windows Azure Portal, choose the VM size you want, the number of instances of it you want to run, and then click save.  Changes take effect in seconds: Unlike shared mode, there is no per-site cost when running in reserved mode.  Instead you pay only for the reserved instance VMs you use – and you can run any number of web-sites you want within them at no extra cost (e.g. you could run a single site within a reserved instance VM or 100 web-sites within it for the same cost).  Reserved instance VMs start at 8 cents/hr for a small reserved VM.  Elastic Scale-up/down Windows Azure Web Sites allows you to scale-up or down your capacity within seconds.  This allows you to deploy a site using the shared mode option to begin with, and then dynamically scale up to the reserved mode option only when you need to – without you having to change any code or redeploy your application. If your site traffic starts to drop off, you can scale back down the number of reserved instances you are using, or scale down to the shared mode tier – all within seconds and without having to change code, redeploy, or adjust DNS mappings.  You can also use the “Dashboard” view within the Windows Azure Portal to easily monitor your site’s load in real-time (it shows not only requests/sec and bandwidth but also stats like CPU and memory usage). Because of Windows Azure’s “pay as you go” pricing model, you only pay for the compute capacity you use in a given hour.  So if your site is running most of the month in shared mode (at 1.3 cents/hr), but there is a weekend when it gets really popular and you decide to scale it up into reserved mode to have it run in your own dedicated VM (at 8 cents/hr), you only have to pay the additional pennies/hr for the hours it is running in the reserved mode.  There is no upfront cost you need to pay to enable this, and once you scale back down to shared mode you return to the 1.3 cents/hr rate.  This makes it super flexible and cost effective. Improved Custom Domain Support Web sites running in either “shared” or “reserved” mode support the ability to associate custom host names to them (e.g. www.mysitename.com).  You can associate multiple custom domains to each Windows Azure Web Site.  With today’s release we are introducing support for A-Records (a big ask by many users). With the A-Record support, you can now associate ‘naked’ domains to your Windows Azure Web Sites – meaning instead of having to use www.mysitename.com you can instead just have mysitename.com (with no sub-name prefix).  Because you can map multiple domains to a single site, you can optionally enable both a www and naked domain for a site (and then use a URL rewrite rule/redirect to avoid SEO problems). We’ve also enhanced the UI for managing custom domains within the Windows Azure Portal as part of today’s release.  Clicking the “Manage Domains” button in the tray at the bottom of the portal now brings up custom UI that makes it easy to manage/configure them: As part of this update we’ve also made it significantly smoother/easier to validate ownership of custom domains, and made it easier to switch existing sites/domains to Windows Azure Web Sites with no downtime. Continuous Deployment Support with Git and CodePlex or GitHub One of the more popular features we released earlier this summer was support for publishing web sites directly to Windows Azure using source control systems like TFS and Git.  This provides a really powerful way to manage your application deployments using source control.  It is really easy to enable this from a website’s dashboard page: The TFS option we shipped earlier this summer provides a very rich continuous deployment solution that enables you to automate builds and run unit tests every time you check in your web-site, and then if they are successful automatically publish to Azure. With today’s release we are expanding our Git support to also enable continuous deployment scenarios and integrate with projects hosted on CodePlex and GitHub.  This support is enabled with all web-sites (including those using the “free” scaling mode). Starting today, when you choose the “Set up Git publishing” link on a website’s “Dashboard” page you’ll see two additional options show up when Git based publishing is enabled for the web-site: You can click on either the “Deploy from my CodePlex project” link or “Deploy from my GitHub project” link to walkthrough a simple workflow to configure a connection between your website and a source repository you host on CodePlex or GitHub.  Once this connection is established, CodePlex or GitHub will automatically notify Windows Azure every time a checkin occurs.  This will then cause Windows Azure to pull the source and compile/deploy the new version of your app automatically.  The below two videos walkthrough how easy this is to enable this workflow and deploy both an initial app and then make a change to it: Enabling Continuous Deployment with Windows Azure Websites and CodePlex (2 minutes) Enabling Continuous Deployment with Windows Azure Websites and GitHub (2 minutes) This approach enables a really clean continuous deployment workflow, and makes it much easier to support a team development environment using Git: Note: today’s release supports establishing connections with public GitHub/CodePlex repositories.  Support for private repositories will be enabled in a few weeks. Support for multiple branches Previously, we only supported deploying from the git ‘master’ branch.  Often, though, developers want to deploy from alternate branches (e.g. a staging or future branch). This is now a supported scenario – both with standalone git based projects, as well as ones linked to CodePlex or GitHub.  This enables a variety of useful scenarios.  For example, you can now have two web-sites - a “live” and “staging” version – both linked to the same repository on CodePlex or GitHub.  You can configure one of the web-sites to always pull whatever is in the master branch, and the other to pull what is in the staging branch.  This enables a really clean way to enable final testing of your site before it goes live. This 1 minute video demonstrates how to configure which branch to use with a web-site. Summary The above features are all now live in production and available to use immediately.  If you don’t already have a Windows Azure account, you can sign-up for a free trial and start using them today.  Visit the Windows Azure Developer Center to learn more about how to build apps with it. We’ll have even more new features and enhancements coming in the weeks ahead – including support for the recent Windows Server 2012 and .NET 4.5 releases (we will enable new web and worker role images with Windows Server 2012 and .NET 4.5 next month).  Keep an eye out on my blog for details as these new features become available. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• Advice needed for a home network setup (hardware & software) to handle many clients and potentially heavy traffic

  - by posdef

  I have recently decided to re-structure the home network of our flatshare here. Here's a quick outline of the situation. I envision to have the following 4 devices connected to the router via cable: Xbox 360 IP phone Printer QNAP server (Web, File and Multimedia) We are three people living here, so on top of that there will be to 5-6 computers/mobile devices connecting as wireless clients. My goal is to be able to transfer files (when needed) between the computer and the Multimedia server, which I can reach via 360 and play on the TV. I also would like to keep a high level of security; right now I have the encryption on WPA2 and MAC filtering. I don't believe the web server will get heavy traffic, though I would like to have it responsive. Likewise, I don't have a habit of downloading via torrent etc, but I greatly appreciate my network being responsive and fast, especially when I am browsing or streaming high quality media. Now my questions are: is this setup feasible? smart? efficient? can this be improved somehow? my current router (D-Link DI624) and the previous one (DI-524) used to have spontaneous drops in network, which I find highly irritating. I don't believe in my router, especially now that it completely crashed when I was test-running the setup by transferring a large media file to server while xbox was playing music from the server, and two computers browsing the net. Do I need to get new hardware, if so, any recommendations for a reliable and fast router?

  Read the article

• Can't log in after restoring from Time Machine

  - by Jay Conrod

  My friend uses a Macbook Pro with Snow Leopard 10.6.2. She uses both FileVault and Time Machine to preserve her data. Recently, she suffered a hard disk failure. After restoring from Time Machine using the Snow Leopard install disk, she gets the following error when logging in: You are unable to log in to the FileVault user account at this time. Logging into the account failed because an error occurred. When examining the file system through Terminal, I noticed her home directory is not present: there is no /Users/username directory, or the FileVault .sparsebundle file that's supposed to be there. When using Time Machine.app on /Users, it appears as if her home directory as never there. Additionally, I did a search on the backup disk with the following command: sudo find /Volumes/backup -name '*.sparsebundle' No results. She told me that after working with some large data files, Time Machine would come on, and it would sound like it was transferring a lot of data to the hard disk. Time Machine must have been doing something, right? How can we recover her files? Are they still there?

  Read the article

• Intel Atom overheating in ASUS EEE Box 1501P

  - by Sergey L.

  I have had an ASUS EEE Box 1501P for just a little bit over a year. Of course it breaks 2 months after the warranty runs out. http://www.asus.com/Eee/EeeBox_PC/EeeBox_PC_EB1501P/ I have been using the box as a Home Media Center. Running mostly 24/7 often pausing a video overnight. Since last week the fan started running extremely loud. After some digging I found that the Intel Atom CPU in it is overheating and the built-in sensor is reporting temperatures way over 105°C. This got me worried, so I took the unit apart. Completely vacuumed the heat sink, oiled the fan, but the unit is still showing the same behaviour. After turning it on and just observing the hardware monitor in the BIOS the temperature slowly rises from 40°C to over 95°C in appx 5 min. I am running the newest BIOS and a lightweight Linux OPENELEC OS with XBMC on it. Now I am wondering if it could be a faulty heat sensor in the Atom. Recommended running temperature is up to 85°C, but I have not detected any performance hits when running at the above mentioned 105°C and there seem to be no software faults. How can an Atom with an attached heat sink and a fan running at full capacity even get this hot in the first place at 0 load? Aren't those things designed to generate virtually no heat? Could it be a faulty heat sensor? What shall I try to fix this? I would prefer not to damage the CPU, since it is hard fused into the motherboard and cannot be replaced. I could remove the heat pipe/heat sink, but it is getting hot, so heat is properly transferring from the CPU to the heat pipe, the fan is running at full capacity, is recently oiled and warm air is making it out of the exhaust. Edit: One more note: The North-bridge (or whatever it is called nowadays) is on the same heat pipe.

  Read the article

• How do I diagnose a bottleneck in an Intel Atom based Ubuntu server?

  - by Jon Cage

  I have a small media server at home which has software raid and a gigabit link to the rest of my network. For some reason though, I only get ~10MB/s transfers when copying to/from the server. I use software RAID5 (mdadm) over 4 1TB disks. On top of that I then use LVM to give me a huge pool of disk space which is then split up into multiple partitions which can be resized as and when they need it. I'm guessing this it most likely the cause, but I'd like to know for sure where the root cause is. So, how can I benchmark network throughput (Windows 7 desktop <- Ubuntu server) and hard disk performance to try and identify where my bottleneck might be? [Edit] If anyone's interested, the motherboard is an Intel Desktop Board D945GCLF2. So that's a 300 series Atom processor with the Intel® 945GC Express Chipset [Edit2] I feel like such a fool! I just checked my desktop and I had the slower of the two onboard NICs plugged in so the server is probably not at fault here. Transferring a copy of ubuntu off the server I get ~35-40MB/s according to Windows 7. I'll do those HD tests when I get a chance though (just for completeness).

  Read the article

• How to prioritize openvpn traffic?

  - by aditsu

  I have an openvpn server, with one network interface. VPN traffic is extremely slow. I tried to do traffic control with this configuration (currently): qdisc del dev eth0 root qdisc add dev eth0 root handle 1: htb default 12 class add dev eth0 parent 1: classid 1:1 htb rate 900mbit #vpn class add dev eth0 parent 1:1 classid 1:10 htb rate 1500kbit ceil 3000kbit prio 1 #local net class add dev eth0 parent 1:1 classid 1:11 htb rate 10mbit ceil 900mbit prio 2 #other class add dev eth0 parent 1:1 classid 1:12 htb rate 500kbit ceil 1000kbit prio 2 filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip sport 1194 0xffff flowid 1:10 filter add dev eth0 protocol ip parent 1:0 prio 2 u32 match ip dst 192.168.10.0/24 flowid 1:11 qdisc add dev eth0 parent 1:10 handle 10: sfq perturb 10 qdisc add dev eth0 parent 1:11 handle 11: sfq perturb 10 qdisc add dev eth0 parent 1:12 handle 12: sfq perturb 10 But it's still extremely slow. I have an imaps connection that keeps transferring data continuously (I successfully limited the rate) but with openvpn I can't seem to get more than about 100kbit/s The internet connection speed is about 3mbit/s (symmetric) What could be the problem? Does the sport filter work for udp?

  Read the article

• Is it possible to re-cab an Administrative Install Point?

  - by Nathaniel Bannister

  We have Acrobat 8 Pro at work, and our media was painfully out of date. Rather than install all of the machines at 8.0.0 and then do the 6 or 7 consecutive reboots adobe expects you to be ok with I decided I'd integrate the .msp files into the installer. After reading up on it, I figured out the exact patch order that adobe required, extracted my cd to an Administrative install point, and ran the patches against it: msiexec /a AcroPro.msi /p AcrobatUpd810_efgj_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd811_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd812_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd813_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd816_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd817_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd820_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd822_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd823_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd825_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd826_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" Now I have a AIP that is fully patched to 8.2.6 (Tested working prior to attempting to CAB it), but is absolutely huge (1.2gb) what I would like to do is take the folders within the AIP and put them back into a cab file for the sake of convenience in transferring the files around. I tried the command: cscript "C:\Program Files\Microsoft SDKs\Windows\v7.0\Samples\sysmgmt\msi\scripts\WiMakCab.vbs" AcroPro.msi Data1 /L /C /S Per the guide I was using, while this did produce the cab file I Wanted, however the resulting MSI fails to install with an error 2602: It's been a while since I've done something like this, and it's probably a glaring oversight on my part, but any insight would be much appreciated.

  Read the article

• Error occurs when Win 7 opens

  - by user1708748

  I have an HP customized laptop barely a week old. Since yesterday it has given me an error message while opening Windows- every time. it gives error code (0x40000015) refers to an exception at location (0x0033fa4d). I have 64 bit Win 7 and had been transferring files. And installing programs. 8 GB Ram 650 gb hard drive. Not sure which program caused this. Q's that I've seen with this error code all say it occurs while shutting down. A search re. error code told me to use a removal tool. When I downloaded the tool,I got a message saying it is not compatible with Windows 7. Is that really possible? Search re. location code yielded nothing I am an intermediate user. I can restore to an earlier time but I don't know which program might do this again.

  Read the article

• Dropbox failing to update?

  - by Mick

  I have two PC's at home. One XP the other Windows 7-64bit. I have a word document that I edit on either PC - to enable this I have the file stored in a Dropbox folder. This usually works fine - but sometimes I find that the file does not get updated on my windows7 PC. I.e. I edit the file on my Windows XP machine, then go to my Windows 7 PC and see that there is a previous, old, datestamp on the file and sure enough if I open up the file to have a look, I see that the latest edits are not included. If I right-click on the file and select "Browse on Dropbox website" I see that the latest file is correctly there. Surely there must be some option to say please update this file - but can find no such thing. Has something gone wrong? I should point out that my wireless internet connection is a little intermittent - could this have caused some glitch? By the way I do not leave the old file open in word on my Windows-7 PC as I can well imagine that would cause trouble. Also I should mention that the icon on the document has the little green tick on it showing that Dropbox is not in the process of doing a transfer. Also the Dropbox icon in my system tray also has the green tick - so Dropbox is not busy transferring some other file(s). If I hover the mouse over the Dropbox icon I get the tooltip "All files up to date".

  Read the article

• Limit the amount of data that can be stored in a folder on Ubuntu Server 12.04?

  - by dougoftheabaci

  I'm in the process of building my first server. It's up, it's running, I'm transferring copious amounts of data away from my horrid little Drobo (DO NOT BUY ONE OF THESE, EVER). However, there's one thing I have yet to do: I'd like to set it up for Time Machine backups as well. I've seen all the guides and I have some idea of how to set the whole thing up, but the issue is that Time Machine will just fill up as much space as you let it. So if I let it lose in my 8 TB zpool it'll slowly consume every last available sector. This, of course, is not acceptable. I have a folder at the root of my zpool called "ZFS Time Machine" and I would like to limit it to 1 TB (all I need for backup purposes). However, I have no idea how to do that. Is this possible? I can continue using a small external hard drive attached via FW800 if I have to but I'd much rather prefer putting everything on my server.

  Read the article

• ASA Slow IPSec Performance with Inconsistent Window Size

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• Code Reuse is (Damn) Hard

  - by James Michael Hare

  Being a development team lead, the task of interviewing new candidates was part of my job.  Like any typical interview, we started with some easy questions to get them warmed up and help calm their nerves before hitting the hard stuff. One of those easier questions was almost always: “Name some benefits of object-oriented development.”  Nearly every time, the candidate would chime in with a plethora of canned answers which typically included: “it helps ease code reuse.”  Of course, this is a gross oversimplification.  Tools only ease reuse, its developers that ultimately can cause code to be reusable or not, regardless of the language or methodology. But it did get me thinking…  we always used to say that as part of our mantra as to why Object-Oriented Programming was so great.  With polymorphism, inheritance, encapsulation, etc. we in essence set up the concepts to help facilitate reuse as much as possible.  And yes, as a developer now of many years, I unquestionably held that belief for ages before it really struck me how my views on reuse have jaded over the years.  In fact, in many ways Agile rightly eschews reuse as taking a backseat to developing what's needed for the here and now.  It used to be I was in complete opposition to that view, but more and more I've come to see the logic in it.  Too many times I've seen developers (myself included) get lost in design paralysis trying to come up with the perfect abstraction that would stand all time.  Nearly without fail, all of these pieces of code become obsolete in a matter of months or years. It’s not that I don’t like reuse – it’s just that reuse is hard.  In fact, reuse is DAMN hard.  Many times it is just a distraction that eats up architect and developer time, and worse yet can be counter-productive and force wrong decisions.  Now don’t get me wrong, I love the idea of reusable code when it makes sense.  These are in the few cases where you are designing something that is inherently reusable.  The problem is, most business-class code is inherently unfit for reuse! Furthermore, the code that is reusable will often fail to be reused if you don’t have the proper framework in place for effective reuse that includes standardized versioning, building, releasing, and documenting the components.  That should always be standard across the board when promoting reusable code.  All of this is hard, and it should only be done when you have code that is truly reusable or you will be exerting a large amount of development effort for very little bang for your buck. But my goal here is not to get into how to reuse (that is a topic unto itself) but what should be reused.  First, let’s look at an extension method.  There’s many times where I want to kick off a thread to handle a task, then when I want to reign that thread in of course I want to do a Join on it.  But what if I only want to wait a limited amount of time and then Abort?  Well, I could of course write that logic out by hand each time, but it seemed like a great extension method: 1: public static class ThreadExtensions 2: { 3: public static bool JoinOrAbort(this Thread thread, TimeSpan timeToWait) 4: { 5: bool isJoined = false; 6:  7: if (thread != null) 8: { 9: isJoined = thread.Join(timeToWait); 10:  11: if (!isJoined) 12: { 13: thread.Abort(); 14: } 15: } 16: return isJoined; 17: } 18: } 19:  When I look at this code, I can immediately see things that jump out at me as reasons why this code is very reusable.  Some of them are standard OO principles, and some are kind-of home grown litmus tests: Single Responsibility Principle (SRP) – The only reason this extension method need change is if the Thread class itself changes (one responsibility). Stable Dependencies Principle (SDP) – This method only depends on classes that are more stable than it is (System.Threading.Thread), and in itself is very stable, hence other classes may safely depend on it. It is also not dependent on any business domain, and thus isn't subject to changes as the business itself changes. Open-Closed Principle (OCP) – This class is inherently closed to change. Small and Stable Problem Domain – This method only cares about System.Threading.Thread. All-or-None Usage – A user of a reusable class should want the functionality of that class, not parts of that functionality.  That’s not to say they most use every method, but they shouldn’t be using a method just to get half of its result. Cost of Reuse vs. Cost to Recreate – since this class is highly stable and minimally complex, we can offer it up for reuse very cheaply by promoting it as “ready-to-go” and already unit tested (important!) and available through a standard release cycle (very important!). Okay, all seems good there, now lets look at an entity and DAO.  I don’t know about you all, but there have been times I’ve been in organizations that get the grand idea that all DAOs and entities should be standardized and shared.  While this may work for small or static organizations, it’s near ludicrous for anything large or volatile. 1: namespace Shared.Entities 2: { 3: public class Account 4: { 5: public int Id { get; set; } 6:  7: public string Name { get; set; } 8:  9: public Address HomeAddress { get; set; } 10:  11: public int Age { get; set;} 12:  13: public DateTime LastUsed { get; set; } 14:  15: // etc, etc, etc... 16: } 17: } 18:  19: ... 20:  21: namespace Shared.DataAccess 22: { 23: public class AccountDao 24: { 25: public Account FindAccount(int id) 26: { 27: // dao logic to query and return account 28: } 29:  30: ... 31:  32: } 33: } Now to be fair, I’m not saying there doesn’t exist an organization where some entites may be extremely static and unchanging.  But at best such entities and DAOs will be problematic cases of reuse.  Let’s examine those same tests: Single Responsibility Principle (SRP) – The reasons to change for these classes will be strongly dependent on what the definition of the account is which can change over time and may have multiple influences depending on the number of systems an account can cover. Stable Dependencies Principle (SDP) – This method depends on the data model beneath itself which also is largely dependent on the business definition of an account which can be very inherently unstable. Open-Closed Principle (OCP) – This class is not really closed for modification.  Every time the account definition may change, you’d need to modify this class. Small and Stable Problem Domain – The definition of an account is inherently unstable and in fact may be very large.  What if you are designing a system that aggregates account information from several sources? All-or-None Usage – What if your view of the account encompasses data from 3 different sources but you only care about one of those sources or one piece of data?  Should you have to take the hit of looking up all the other data?  On the other hand, should you have ten different methods returning portions of data in chunks people tend to ask for?  Neither is really a great solution. Cost of Reuse vs. Cost to Recreate – DAOs are really trivial to rewrite, and unless your definition of an account is EXTREMELY stable, the cost to promote, support, and release a reusable account entity and DAO are usually far higher than the cost to recreate as needed. It’s no accident that my case for reuse was a utility class and my case for non-reuse was an entity/DAO.  In general, the smaller and more stable an abstraction is, the higher its level of reuse.  When I became the lead of the Shared Components Committee at my workplace, one of the original goals we looked at satisfying was to find (or create), version, release, and promote a shared library of common utility classes, frameworks, and data access objects.  Now, of course, many of you will point to nHibernate and Entity for the latter, but we were looking at larger, macro collections of data that span multiple data sources of varying types (databases, web services, etc). As we got deeper and deeper in the details of how to manage and release these items, it quickly became apparent that while the case for reuse was typically a slam dunk for utilities and frameworks, the data access objects just didn’t “smell” right.  We ended up having session after session of design meetings to try and find the right way to share these data access components. When someone asked me why it was taking so long to iron out the shared entities, my response was quite simple, “Reuse is hard...”  And that’s when I realized, that while reuse is an awesome goal and we should strive to make code maintainable, often times you end up creating far more work for yourself than necessary by trying to force code to be reusable that inherently isn’t. Think about classes the times you’ve worked in a company where in the design session people fight over the best way to implement a class to make it maximally reusable, extensible, and any other buzzwordable.  Then think about how quickly that design became obsolete.  Many times I set out to do a project and think, “yes, this is the best design, I can extend it easily!” only to find out the business requirements change COMPLETELY in such a way that the design is rendered invalid.  Code, in general, tends to rust and age over time.  As such, writing reusable code can often be difficult and many times ends up being a futile exercise and worse yet, sometimes makes the code harder to maintain because it obfuscates the design in the name of extensibility or reusability. So what do I think are reusable components? Generic Utility classes – these tend to be small classes that assist in a task and have no business context whatsoever. Implementation Abstraction Frameworks – home-grown frameworks that try to isolate changes to third party products you may be depending on (like writing a messaging abstraction layer for publishing/subscribing that is independent of whether you use JMS, MSMQ, etc). Simplification and Uniformity Frameworks – To some extent this is similar to an abstraction framework, but there may be one chosen provider but a development shop mandate to perform certain complex items in a certain way.  Or, perhaps to simplify and dumb-down a complex task for the average developer (such as implementing a particular development-shop’s method of encryption). And what are less reusable? Application and Business Layers – tend to fluctuate a lot as requirements change and new features are added, so tend to be an unstable dependency.  May be reused across applications but also very volatile. Entities and Data Access Layers – these tend to be tuned to the scope of the application, so reusing them can be hard unless the abstract is very stable. So what’s the big lesson?  Reuse is hard.  In fact it’s damn hard.  And much of the time I’m not convinced we should focus too hard on it. If you’re designing a utility or framework, then by all means design it for reuse.  But you most also really set down a good versioning, release, and documentation process to maximize your chances.  For anything else, design it to be maintainable and extendable, but don’t waste the effort on reusability for something that most likely will be obsolete in a year or two anyway.

  Read the article

• Multicast image restoration with adaptive speed

  - by Clinton Blackmore

  I'm curious to know if there are any tools for restoring disk images (or even transferring files) via multicast -- for any platform, especially if the project has source available -- where the multicast rate adjusts itself on the fly. On the Mac, all multicast solutions I am aware of (such as Deploy Studio, and NetRestore before it) make use of multicast ASR (apple software restore), which has one glaring deficiency -- you have to set the multicast speed before you start sending a disk image over the network, and that speed is locked in. Either your clients can keep up and restore, or they can't*. It seems to me that it must be possible for the multicast server to adjust the data rate, so you basically say "start sending this image", clients connect, and, if they can't keep up, they tell the server so it slows down. (Likewise, I'd expect the server to try speeding up if no client is having difficulties keeping up, and I'd expect to be able to cap that maximum throughput so that other network activities can go on without being resource starved.) So, what sort of tools are out there? For Linux? Windows? Is there something for the Mac I've overlooked. [It just kills me that it is true that, by the time you get multicast up and going at a good speed to restore a lab, you could've unicasted the data to all the computers and be done.] * There is a little leeway involved. I think individual clients can say, "I missed a little bit of data" and get it, and they can opt to listen in the next time the image is sent over the network, but on the whole, if they missed it the first go round, you have to image the machine again, and there is no time savings.

  Read the article

< Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >