Search Results

Search found 1938 results on 78 pages for 'josh ryan'.

Page 30/78 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

• growing EBS RAID volume

  - by Ryan Fernandes

  I've created a RAID0 configuration with two 1GB EBS volumes, mounted at /dev/md0 using mdadm and formatted with XFS Next, I copied some files over to fill the volume to around 30% of its capacity (of 2GB) I then created snapshots of the volumes using ec2-consistent-snapshot and created volumes of the said snapshots but specified the volume size to be 2GB (effective doubling the capacity on each disk) I then spun up a new instance, assembled the RAID0 configuration on /dev/md0 from the 2 volumes mentioned above and mount it to /vol df -hT showed /vol as 2GB (as expected) Now I ran sudo xfs_growfs -d /vol. The command completed normally but reported blocks changed from 523776 to 524160 (only!) and df -hT still showed /vol as 2GB (instead of the expected 4GB) I rebooted, remounted, reassembled the RAID but it still reports the old size. EDIT: trying to grow the RAID using mdadm --grow yields mdadm: raid0 array /dev/md0 cannot be reshaped Is there any other way I can grow a RAID0 array?

  Read the article

• Unattended Install of Zend Server license

  - by Zoop - Josh

  I have a Zend Server 5.6 development license and I wanted to know if there is a way to apply the license during install, rather than via the web interface after it has installed. I ask because I administer our server environment via Rightscale and have automated the creation of the server, however it still requires manual input for the license details. We regularly fire up a staging server to do final tests before pushing to production and it would be great if it were completely hands off.

  Read the article

• Installed Bunch of New Fonts on Windows 7 - Now None Show Up and System Lags

  - by Josh Stodola

  So I went to install about 5,000 fonts on my Windows 7 64-bit machine. It was slow to install them, and I had to leave. I came back and my PC was shut down, and I had to go through the Windows recovery BS when I powered it on. Now my computer runs EXTREMELY slow and any program that has a font menu locks up my whole machine (nothing in Microsoft Office works). When I go to "Fonts" in the control panel, it says 0 items. I went through all of the font settings trying to get them to appear. Nothing helps. I tried to bring up the Character Map and that froze up my machine too. How can I fix this? If I do not get this issue resolved soon, I am wiping this drive and going back to XP (and probably never purchasing another version of Windows again). I never had any issues with XP and have had nothing but performance problems when switching to Windows 7. My quad-core intel extreme with 8GB of RAM should never flinch with the kind of work that I do, and something simple like playing a song off an external HD takes up to five seconds on Windows 7. Unbelievable that I had to pay for this crap!

  Read the article

• What's a good(affordable) business router that can limit traffic to certain machines(ips/ports)?

  - by Ryan Detzel

  We are using the basic Verizon router but it sucks so we're looking for a new one that allows us to limit users and our hadoop cluster to certain limits. Our problem is one person can start downloading something and kill the network and every hour we download logs into our cluster but it floods the network unless we rate limit it. Ideally we want to be able to say: total: 35 mbps Hadoop Cluster (15 mbps) Phones (1 mbps) Office(25 people) (19mbps but no one machine can have more than 5mbps)

  Read the article

• apache spawning too many processes despite maxclient and other constraints

  - by Josh Nankin

  Here are my MPM constraints: StartServers 10 MinSpareServers 10 MaxSpareServers 10 MaxClients 10 MaxRequestsPerChild 2000 However despite this, I have over 20 apache processes running currently, and in the past hour or two there have been as many as 40-50. Shouldn't the MaxClient and MaxSpareServers keep the number of processes under control (i.e. about 10)? Is there something I'm missing?

  Read the article

• Suggestions for someone wanting to become a Laptop Reseller

  - by Josh B.

  First of all, to give you a little background... I have had my Microsoft A+ for several years now. I used to run a small business repairing Xbox 360 consoles and I am currently a Network Engineer for a company in Ohio. I definitely know my way around a computer. I miss running a small business on the side and I'd like to get something going again. There is a really high demand in my area for Laptops and I was thinking about starting a small Laptop store out of my house. What is the best way to do this? I was assuming that the best way would be to buy barebones systems and build them yourself. If this is the best method, I would be very interested in any resources to get parts and such. Apparently Laptop parts aren't the easiest thing to come by (especially at a good price). Does anyone have any suggestions about how to get something like this going?

  Read the article

• Does NTFS performance degrade significantly in volumes larger than five or six TB?

  - by Josh Yeager

  One of my customers is planning to set up a new document store, which will probably grow by 1-2TB per year. One of my co-workers says that Windows performance is extremely bad if it has a single NTFS volume that is bigger than five or six TB. He thinks that we need to set up their system with multiple volumes so that no single volume will exceed that limit. Is this a real problem? Does Windows or NTFS slow down when the volume size reaches several terabytes? Or is it possible to create a single volume of 10 or more TB?

  Read the article

• VPN Configuration

  - by Josh

  How can I allow incoming connections on a Windows 7 machine that is connected to VPN? I have some services listening on certain ports that I have forwarded from my router. When the VPN is disconnected, I can connect to these services from my internal network as well as from the Internet without issue. When I connect my VPN however, I am still able to access the ports from my internal network, but not remotely. I think I need a split tunnel setup, and there is an option in the VPN settings to Use Default Gateway on remote network. I want this option enabled so all my traffic is routed through the VPN, but I want incoming connections to be allowed on my internal network IP from the Internet. Is there some hybrid way to set this up with routing?

  Read the article

• After installing Office365 can you go back to Office 2008 (without the CD)

  - by Ryan

  I got this laptop from my dad and don't have the Microsoft Office 2008 CD which is what he had installed when he gave it to me to use. Now I've got a client that wants me to do some freelance work and sent me to Microsoft Exchange and the first thing it wants me to do in the Exchange is install Office365. The client mentioned very briefly that he would get me the software if necessary but he wasn't specific about what software. Now that I see it my concern is after the job is done I'll be left with a monthly bill to have Office. Will it be possible to go back to Office 2008 without having the CD?

  Read the article

• Domain user periodically can't login, but only temporarily?

  - by Josh

  Ok, this is a strange one that I'm having trouble replicating letting alone solving. I have a user who uses two computers (both XP sp3) on the domain with a roaming profile. She has no problems on her personal computer but occasionally needs to use a shared computer. On this shared computer she is sometimes (~once a week) unable to login with the error message "Username or password incorrect. Check username password and domain and try again." I've checked when this happens and her username and password are indeed entered correctly. Now the strange part - if someone else logs in to the computer (which so far always works) and then logs out she is able to log in after that. This problem began after a recent and long overdue password change. I've tried to replicate this problem after a reboot, or after another user logs out to no avail. Any suggestions on troubleshooting or replicating this one? Anyone experienced something similar?

  Read the article

• SQL Server 2000, large transaction log, almost empty, performance issue?

  - by Mafu Josh

  For a company that I have been helping troubleshoot their database. In SQL Server 2000, database is about 120 gig. Something caused the transaction log to grow MUCH larger than normal to over 100 gig, some hung transaction that didn't commit or roll back for a few days. That has been resolved and it now stays around 1% full or less, due to its hourly transaction log backups. It IS my understanding that a GROWING transaction log file size can cause performance issues. But what I am a little paranoid about is the size. Although mainly empty, MIGHT it be having a negative effect on performance? But I haven't found any documentation that suggests this is true. I did find this link: http://www.bigresource.com/MS_SQL-Large-Transaction-Log-dramatically-Slows-down-processing-any-idea-why--2ahzP5wK.html but in this post I can't tell if their log was full or empty, and there is not any replies to the post in this link. So I am guessing it is not a problem, anyone know for sure?

  Read the article

• How to host ASP.NET application externally?

  - by Josh

  I have an ASP.NET application that I can get to locally by going to 192.168.1.102:81/TestApp. I would like to host the application externally by going to domain.com:81/TestApp (I already have my domain pointing to my router and this works fine - I have apache running on port 80 on another server). I modified the router settings to point any request coming through port 81 to 192.168.1.102. I am still having trouble accessing the ASP.NET site (I get the error message that "This link appears to be broken"). Am I missing something? How can I redirect domain.com:81/TestApp to my ASP.NET application? Thanks.

  Read the article

• What should a hosting company do to prepare for IPv6?

  - by Josh

  At the time of writing The IPv4 Depletion Site estimates there are 300 days remaining before all IPv4 addresses have been allocated. I've been following the depletion of IPv4 addresses for some time and realize the "crisis" has been going on for many years and IPv4 addresses have lasted longer than expected, however... As the systems administrator for a small SaaS / website hosting company, what steps should I be taking to prepare for IPv6? We run a handful of CentOS and Ubuntu Linux systems on managed hardware in a remote datacenter. All our servers have IPv6 addresses but they appear to be link local addresses. Our primary business function is website hosting on a proprietary website CMS system. One of my concerns is SSL certificates; at the moment every customer with an SSL certificate gets a dedicated IPv4 IP address. What else should I be concerned about / what action should I take to be prepared for IPv4 depletion?

  Read the article

• How to tell Windows 7 "sleep when laptop is closed, unless there's an external monitor connected; then use that"?

  - by Josh

  Most of the time, I would like my Windows 7 laptop to sleep when I close it. But sometimes, I like to connect an external monitor over DVI. I would like my laptop to use the external monitor when I close the lid, but only when a monitor is connected to the DVI port. Otherwise, sleep when closed. Is there any way I can do that, without manually changing the power settings every time I decide to use the monitor?

  Read the article

• How do I connect to and factory reset a Catalyst 3560 Switch?

  - by Josh

  My company just bought another company. In their server room they had some older hardware, which I would like to repurpose. One of these is a Cisco Switch: C3560G-48TS-S. I found some instructions about this switch here but this is not a guide for a beginner. I have no idea how to connect to this thing to begin running the commands. It says Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. But I can't find anything on how to do this (assuming with telnet?) or even what program to use. I also don't know how to find the IP address of the device to connect to it. My research also says once I get in there, I need to run clear config all Is this the right command? Also, what if I can't get the username and password for these devices? Is there some way to factory reset (my only experience is with devices that have a hardware reset button) EDIT: I should note that when I push the button on the front the three lights blink, which according to the documentation indicated the switch is configured and "not available for express setup"

  Read the article

• After RAID failure SBS 2008 issues logging in and Exchange store does not mount

  - by Josh R

  today has been one of those days. Yesterday a hard drive in our Dell Poweredge 2900 server failed and the RAID array didn't degrade gracefully, so I called Dell (Server still under warranty) and got an engineer to work though the RAID issues with me. He was a nice guy but didn't do too much. We tried to put the RAID in a state where it was bootable and even though we only lost one disk there are still issues with the server. Once we got the server to boot there was an error message saying that the logonui.exe was corrupted and we needed to run chkdsk. I clicked through the error messages and the login screen never came up. So I power cycled the server and it chkdsk automatically but the login screen didn't appear. I tried safe mode, no difference there either. So the issues I am currently having are: 1) The server boots up, the loading windows screen comes up then it dumps me into a black screen where I can only see my mouse cursor. Ctrl+Esc doesn't work Ctrl+Alt+Del doesn't work 2) Some of the services come up: DHCP, DNS, DFS, and Print come up 3) The exchange information store and transport service don't start - I tried using mmc to connect to services.msc on the computer and start them but they throw an error message of "Can't start because group or dependency failed" Has anyone had a problem like this? Can anyone offer some guidance? Thanks a bunch!

  Read the article

• Hard Disk based storage library

  - by Ryan M.

  We have a Tandberg T24 tape device to handle all of our long term backups right now. We decided that we're not backing up nearly everything that we would like to and that we still have a lot of vulnerabilities. To get to where we want to be, we're going to have to back up a lot more servers than we're currently doing. All of our internal servers have some sort of directly attached drive (I.e. LaCie Raid box or a simple portable hard drive) doing backups, but what we want to do is get those backups off-site. The current tape drive is directly attached via SCSI to a Windows Server 2008 File Server. So to back up anything to tape, it has to be funneled through the File Server. With the current increase that we have planned, I don't think that funneling everything through the File Server is the right course of action and I'm thinking that maybe a second backup device would be more appropriate. I would like your input on a couple of ideas. 1) Doing HDD instead of tape. Tape is hard to deal with. We have a regular rotation cycle, so they don't need years and years of shelf life, so I'm wondering if something HDD-based would be better. 2) Something accessible over the network. Instead of having the device directly attached to one specific machine, have it available to all the servers over the network. Our File Server is a 12-disk raid 6 set up.. I was thinking something like that, but with no raid involved, all disks are stand alone so they can be used/installed/removed on an individual basis. Does any such thing exist? Thanks for your ideas. I'm really interested to hear about some of the solutions you guys are using..

  Read the article

• Primary/secondary ethernet interfaces in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local...

  Read the article

• How can I prevent Virtualmin from storing passwords in cleartext?

  - by Josh

  I am really surprised at this behavior. In Virtualmin, I can see the password for any SSH user by clicking the "(Show..)" link next to the "Password ( ) Leave unchanged" option in a variety of locations. I have found that the passwords for all users including users with SSH access are stored in cleartext files in /etc/webmin/... This seems like an unnecessary risk! How can I prevent Virtualmin from storing passwords in this manner?

  Read the article

• Status: 0xc00000e9

  - by Ryan Galloza

  When I start up windows normally it just freezes , I click "Launch Startup Repair" I get this: "Windows has encountered a problem communicating with a device connected to your computer. This error can be caused by unplugging a removable storage device such as an external USB drive while the device is in use, or by faulty hardware such as a hard drive or CD-ROM drive that is failing. Make sure any removable is properly connected and then restart your computer If you continue to receive this error message, contact the hardware manufacturer" How do I fix this problem?

  Read the article

• second monitor wont display

  - by Ryan

  hi all my problem is this: i have one video card (radeon hd 4350) and 2 monitors (dell). the first monitor works using dvi-to-dvi. the second does not, using hdmi-to-dvi. the monitor does not register any input. however when i use vga-to-vga, the second monitor does work, with a typically low vga resolution. we have tested the hdmi-to-dvi cable, so why does the monitor not register any input? using windows vista. i have installed all the lastest drivers, done all the basic stuff etc. any help at all would be appreciated. thanks

  Read the article

• Can I use a micro ec2 instance as a load balancer for my other large ec2 instances?

  - by Ryan Detzel

  The issue I'm having is I want to upgrade that instance often(security patches, etc) but I'm affriad something will fail and the site will be down. So, I want to have another server setup and load balance between the two that way I can easily disable one, upgrade it and once it's working add it back in the mix and repeat. What kind of machine is needed for a load balancer? Would the micro instance work just fine? The site gets anywhere from 3-10k hits/day. I plan on using nginx as the load balancer.

  Read the article

• how to change zone of a extented webapplication-SharePoint?

  - by Ryan

  I have extended a webapplication and set its zone to Intranet but now we decided to make that site anonymous I made all the settings in authentication provider and site collection settings but its still showing its zone as Intranet . I read that its best practice to keep Internet as the zone for anonymous access.. How can I change it now and does it affect leaving it as Intranet?

  Read the article

• HTTPS version of page throws 404, regular HTTP appears fine?

  - by Ryan

  I'm having a strange issue with a website in IIS on Windows Server 2003. It has a valid wild card certificate on it, however when I use HTTPS on the page I get a 404 not found. Without HTTPS it shows up fine. Also, if I go to the domain root of the site using HTTP the homepage shows up, but with HTTPS it REDIRECTS ME to a totally different website installed on the same IIS server. I am quite confused. I tried giving each site a unique IP address but it didn't change anything, I also tried changing the SSL ports, no luck. This IIS is setup to run PHP also. What could I check to resolve this?

  Read the article

• Odd Language In a BIOS Message

  - by Josh

  So I started up my laptop today and was greeted with the following message (not a direct quote): The type of the AC adapter cannot be determined. This may interfere with your computer's performance. Try unplugging the AC adapter and then plugging it back in, thanks. The problem was that I hadn't fully secured the plug into the back of the computer. However, I was a little taken aback when a message from BIOS said, "thanks." Is this normal? Any chance the message was illegitimate (virus)?

  Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >