Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 300/1221 | < Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >

  • VM can’t connect to outside in bridged mode

    - by Kamal
    Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have. My virtual network editor shows that my ethernet adapter(the one my host uses) is used for bridging. It is connected. I don't understand how I can get an IP address from DHCP server. I can't ping any of the DNS servers in generated /etc/resolv.conf which are the same as that of my host

    Read the article

  • No network connectivity for my CentOS 6 installed in VMWare Fusion in MacOSX Lion

    - by gilzero
    I installed CentOS 6.2 (CentOS-6.2-x86_64-minimal.iso) with VMWare Fusion(Version 4.1.2). (Not with EasyInstall). I am using MacOSX Lion, connect to internet via WIFI. The centos installed does not have network connectivity. *How may I configure it to connect to wifi? * Thanks for any help. Below is screenshot of ifconfig: With the setting Network Adapter, I tried both NAT and Bridged WiFi.

    Read the article

  • Using airport extreme base station as a wireless G to wireless N bridge

    - by micmcg
    Due to unfortunate placement of various wall outlets in my new apartment, my adsl 2 modem + router is not able to be placed next to my airport extreme base station (AEBS). I'd prefer not to run cat5 cable between them, but I still want to use the wireless N on the AEBS, because it will have a high speed NAS plugged in via gigabit ethernet so I want to maximise the wireless transfer speed to my 27" iMac. Is it possible to use one of the radios in the airport extreme to bridge the wireless G network with the router, and the wireless N radio to broadcast normally? The only traffic going over the G network should be internet (24mbps ADSL2) so it should never get saturated. Thanks

    Read the article

  • Skype Optimization - Port Forwarding on a Router

    - by user19185
    I was watching this Video which talked about using port-forwarding to optimize your LAN for skype calls. According to the video, as explained in the first couple of minutes in the video, the reason you would need optimization is because if the person your call has a firewall setup, your connection has to go-through a third-party computer to connect to them. I believe I stated this correct (maybe not). None the less, my question is this: do both parties on the call need to enable port forwarding to optimize skype, or just one party (person)?

    Read the article

  • Cisco SA520 to Adtran 1234 no DHCP transfer

    - by Grico
    I am trying to set up a Cisco SA520 to run DHCP on my network. I have a vendor provided switch, the Adtran 1234, and it provides DHCP for our phone systems on VLAN 200. I do not have access to the Adtran, but the vendor gave me a IP on port 1 for WAN and said port 2 should be for the "trust" side should go. I did setup a mini lab where, Adtran 1 went to SA520 WAN port, and SA520 trust 1 went to my laptop. Everything worked fine, I could ping and get internet using the DHCP scope I put on the SA520. I then unplugged my computer from SA520 trust 1 and plugged it into Adtran 2. I plugged my computer into Adtran 23 and I dont get DHCP or even a link light. If I restart my machine, I get a brief link and then it dies once the machine boots. I have tried several ports on the Adtran and none seem to work. Different cables as well. However, when I plug a phone into the Adtran, the phone boot immediately and shows link. Thoughts?

    Read the article

  • MacBook can't use internet, but nslookup and ping both work

    - by Joel Coehoorn
    I have a user with a new high-end MacBook Pro that can't use the internet. He can connect to either our wired or wireless network and do things like browse file shares, but can get no further. When I brought the machine in for testing, I found that I could do an nslookup just fine, and I'm able to ping addresses returned by nslookup just fine. I'm even able to bring up web pages by entering the IP address into the address bar directly. However, when I try to ping the domain name rather than the IP address, it just sits there. So apparently I can either do name resolution or communicate with an address, but not both at the same time. Again, these symptoms occur on both the wired and wireless network. Other machines on our network, including a few other Macs, don't have this issue. Any ideas?

    Read the article

  • windows server 2008r2 with terminal services in multiple networks with different users

    - by phhe
    is there a way to let terminal services make some kind of 'abstraction' over the physical network interfaces of the server so they can be managed via gpo to grant or prohibit access for different users? the basic idea is to have 2 network interfaces (user and server/management) and not letting users within terminal sessions access the server/management network. or is this just impossible ? what would be a better way to do this ?

    Read the article

  • tool for monitoring network traffic on Windows 7 Home

    - by Xah Lee
    for Windows 7 Home Edition: can anyone recommend a tool to monitor network traffic? either build-in or 3rd-party. I like to have a graph view (e.g. as in Task Manager) but also nice are tool that lets me see what IP/port that's incoming/outgoing. Command line is fine. Or even some tutorial. Thanks. (am old unix sys admin and web app dev. Though not much of a network admin and don't know much Windows. I need this tool just for my home PC, not in any pro capacity.)

    Read the article

  • allow SSH to bypass VPN on OSX mavericks, openvpn, pf

    - by zycho42
    My home computer connects to the internet through an OpenVPN connection. However, I would like to be able to connect to my home computer from outside over ssh. Ssh is set up and working, but when I connect to the vpn ssh is only accessible from inside my home network. I figure what's going wrong is my router forwards incoming ssh connections to my mac, but then my mac replies over the vpn, so the connection from outside times out. I've got pf set up for a couple of other things, but I can't figure out how to let the ssh replies bypass the vpn using pf. I've come across other solutions that use ip tables, routing tables and rules, but I can't figure out how to set that up on mavericks. I've been searching for this for a while now but I haven't found a working solution. Any help would be greatly appreciated!

    Read the article

  • USB ports causing Wireless and Mobile Phone tethering drop out

    - by chrolli
    I have a problem with my USB ports and I can't seem to pinpoint the problem. I'm hoping that I can get some idea as to how to troubleshoot my problem. Problem description: I recently bought a USB Wireless Adapter in order to connect my Desktop PC to the WLAN. The dongle keeps dropping off connection regularly on average once a minute. And the connection is slow. What I've tried: I installed a network scanner to determine signal strength. The PC/adapter combo is getting about 70% signal strength. I have a laptop that has an internal Wireless adapter. I moved the laptop near the location of the PC. The signal strength was above 90%. I installed the USB adapter on the laptop. I placed the laptop near the location of the PC. The signal strength was above 80%. And there is no drop out issue. I've isolated the problem to be on the PC. I used internet tethering on my mobile phone in order to test the USB ports. I get the same problem, themobile phone keeps dropping in and out. I plugged the adapter and phone on all USB ports, and it is still dropping out on all ports. I've isolated the problem to be the Motherboard, USB hub. I updated the BIOS, and USB driver. Still dropping out. I noticed that when I used the mobile phone tethering method, the phone (iphone 5) is guarenteed to drop out and does not appear to charge if I jiggle the the 8-pin connector on the base of the phone. If I push the pin tightly on the phone, the phone starts charging, as soon as I let go, it stops and drops out from the PC. This is strange because this doesn't happen when it is plugged to the powerboard. Which means that the 8 pin connector is fine. I'm not sure what the problem is. I assume that it is to do with the USB ports not supplying enough power which in turn causes the devices to intermittently drop out. The reason I say this is because the USB cable works fine when plugged into a powerboard with enough power supplied to the phone. Only when it is plugged into the USB port on the PC, does it drop out. My motherboard is Asus P8z68-v le. My Wireless adapter is the D-link DWA131. I can't seem to find any settings in the BIOS to increase the south bridge voltage so as to supply more power to the USB ports. Although this problem only occurs when I'm trying to hook up to a device supplying internet connection. My USB HDD, Flash drives, and Mouse and Key are working fine! Any suggestions please?

    Read the article

  • Routing internet through ethernet to a computer without a Wireless adapter

    - by Decency
    I'm setting up a small home network. I have a laptop which connects to internet wirelessly- that works fine. I have a desktop connected to this laptop by an ethernet cable which I'd like to access the internet with. In the past, I have used a different laptop to do this and had no problems doing so. Both computers run Windows 7. I have tried setting up a homegroup and disabling Windows firewall, as well as restarting both computers. I can share data but my internet connection can not be accessed through the desktop. (I understand USB network adapters are cheap, I have one on the way but that doesn't solve this issue.) Any help or live chat support if you'd prefer would be appreciated. Thanks!

    Read the article

  • Huawei b260a gsm modem not forwarding gre for pptp tunnel

    - by Priit
    I have a huawei gsm modem that does not want to let gre through. The goal is to connect into a pptp server thats behind the huawei. In the modems port forwarding settings theres a ready made profile for pptp (1723). After activating that the MS pptp test tools show that connection is being initiated but no gre packets make it to the server. After taking a closer look into the modems iptables rules theres nothing in there about gre. So I tried making gre rules manualy into forward and preroute chains without any success what so ever. As far as I can tell theres no ip_gre module present on the device is that needed for gre forwarding? Thats what I'm afraid of that it doesn't support gre in NAT but how would I turn it into a bridge? The wan interface is ppp0 so bridging it with eth0 would not work right? Is there some iptables rule I could use to make the modem let all the traffic just straight through?

    Read the article

  • Constructing radiotap header and ieee80211 header structures for packet injection

    - by hektor
    I am trying to communicate between two laptop machines using Wifi. The structure of the radiotap header and ieee80211 header I am using is: struct ieee80211_radiotap_header { unsigned char it_version; uint16_t it_len; uint32_t it_present; }; /* Structure for 80211 header */ struct ieee80211_hdr_3addr { uint16_t frame_ctl[2]; uint16_t duration_id; unsigned char addr1[ETH_ALEN]; unsigned char addr2[ETH_ALEN]; unsigned char addr3[ETH_ALEN]; uint16_t seq_ctl; }; struct packet { struct ieee80211_radiotap_header rtap_header; struct ieee80211_hdr_3addr iee802_header; unsigned char payload[30]; }; /* In main program */ struct packet mypacket; struct ieee80211_radiotap_header ratap_header; struct ieee80211_hdr_3addr iee802_header; unsigned char addr1[ETH_ALEN] = {0xFF,0xFF,0xFF,0xFF,0xFF,0xFF}; /* broadcast address */ unsigned char addr2[ETH_ALEN] = {0x28,0xcf,0xda,0xde,0xd3,0xcc}; /* mac address of network card */ unsigned char addr3[ETH_ALEN] = {0xd8,0xc7,0xc8,0xd7,0x9f,0x21}; /* mac address of access point i am trying to connect to */ /* Radio tap header data */ ratap_header.it_version = 0x00; ratap_header.it_len = 0x07; ratap_header.it_present = (1 << IEEE80211_RADIOTAP_RATE); mypacket.rtap_header = ratap_header; /* ieee80211 header data */ iee802_header.frame_ctl[0] = IEEE80211_FC0_VERSION_0 | IEEE80211_FC0_TYPE_MGT | IEEE80211_FC0_SUBTYPE_BEACON; iee802_header.frame_ctl[1] =IEEE80211_FC1_DIR_NODS; strcpy(iee802_header.addr1,addr1); strcpy(iee802_header.addr2,addr2); strcpy(iee802_header.addr3,addr3); iee802_header.seq_ctl = 0x1086; mypacket.iee802_header=iee802_header; /* Payload */ unsigned char payload[PACKET_LENGTH]="temp"; strcpy(mypacket.payload , payload); I am able to receive the packets when I test the transmission and reception on the same laptop. However I am not able to receive the packet transmitted on a different laptop. Wireshark does not show the packet as well. Can anyone point out the mistake I am making?

    Read the article

  • Why do the IP addresses randomly change?

    - by GiddyUpHorsey
    I have a network with the following: Cable modem with static IP address Router Desktop - Win 7 VM Host - VMware ESXi 4.0 A couple of VM Guests - Windows Every now and then my Win 7 PC is unable to access some of the VMs. When I ping the VMs by their domain name their IP address shows up as the IP address of the cable modem. Sometimes I can fix it by running ipconfig /flushdns. The IP address will reset back to what it was supposed to be, but occasionally it wont work. Why does this happen and how can I fix it?

    Read the article

  • Spanning-tree setup with incompatible switches

    - by wfaulk
    I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

    Read the article

  • One email user keeps disconnecting from our exchange server

    - by Funky Si
    I have one user who keeps reporting that Outlook keeps disconnecting from our email server. All other users are fine. Our email server is running Exchange 2010 and the client is running Outlook 2003. The disconnection only lasts a moment. I have checked for logs on the client and Exchange server and can not see any reason for the disconnect, On the Client I get EventId 26 telling me Outlook has disconnected and reconnected but no reason why. Can anyone give me some suggestions of things to try and track down where the problem could be? --Update-- I have found the following log file C:\Program Files\Microsoft\Exchange Server\V14\Logging\RPC Client Access which suggests that it is a problem with RPC sessions. Excerpt is below 2013-01-31T15:21:24.015Z,6413,15,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,0,00:00:00,"BS=Conn:24,HangingConn:0,AD:$null/$null/0%,CAS:$null/$null/2%,AB:$null/$null/0%,RPC:$null/$null/1%,FC:$null/0,Policy:ClientThrottlingPolicy2,Norm[Resources:(Mdb)Mailbox Database 0765959540(Health:-1%,HistLoad:0),(Mdb)Public Folder Database 1945427388(Health:-1%,HistLoad:0),];GC:6/1/0;", 2013-01-31T15:21:24.015Z,6413,16,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,PublicLogoff,0,00:00:00,LogonId: 1, 2013-01-31T15:21:24.015Z,6413,16,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,"BS=Conn:24,HangingConn:0,AD:$null/$null/0%,CAS:$null/$null/2%,AB:$null/$null/0%,RPC:$null/$null/1%,FC:$null/0,Policy:ClientThrottlingPolicy2,Norm[Resources:(Mdb)Mailbox Database 0765959540(Health:-1%,HistLoad:0),(Mdb)Public Folder Database 1945427388(Health:-1%,HistLoad:0),];GC:6/1/0;", 2013-01-31T15:21:24.015Z,6417,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,OwnerLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.015Z,6417,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,0x6BA (rpc::Exception),00:02:54.7668000,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0; SessionDropped,"RpcEndPoint: [ServerUnavailableException] Connection must be re-established - [SessionDeadException] Connection doesn't have any open logons, but has client activity. This may be masking synchronization stalls. Dropping a connection." 2013-01-31T15:21:24.015Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,DelegateLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00.0156000,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, 2013-01-31T15:21:24.031Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,Disconnect,0,00:02:54.2364000,, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,OwnerLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,Disconnect,0,00:02:54.4392000,, 2013-01-31T15:21:24.031Z,6416,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,DelegateLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6416,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, Can anyone help point me in the right direction for a solution?

    Read the article

  • No Outbound Internet on Windows Home Server

    - by Kyle B.
    Could someone provide some steps for me to check my internet connection on my Windows Home Server? It seems to have intermittent connectivity issues and I am unsure of how to diagnose the problem because it is a headless (no monitor, no keyboard) machine so the only way to get to the device is via remote desktop (which works fine). When connected to the machine, it doesn't pull up any microsoft.com sites and some other sites it does pull up (i.e. gmail.com) and some it doesn't (stackoverflow.com). To make matters more complicated, it has worked intermittently in the past for reasons unknown. Are there tools I can use to properly diagnose the reason for the connection failure? I can ping 127.0.0.1 just fine, I have internet working on my other router-connected machines, so I'm not sure why this one would fail. Any suggestions would be much appreciated and up-voted :) ** edit - thanks for suggestions guys, I'm going to try these tonight and will update my post. ** edit #2 - I hoping this is a more permanant fix, but I have both changed my port on the router as well as restarted the router at the same time. The internet (for the moment) appears to be working. I will be sure to try everything we have discussed should this problem persist. Thanks, Kyle

    Read the article

  • Internet Sharing via router

    - by mak4pi
    Question: How to setup Internet Sharing among two computers (one Mac 10.5.6, one Ubuntu 9.10) via a router? Situation: The Mac is using AirPort (wireless interface) to connect to router as 192.168.1.101. The Ubuntu is using an ethernet cable to connect to router as 192.168.1.104. Visual: Mac )))))) Router ======= Ubuntu Any ideas are greatly appreciated. Thanks.

    Read the article

  • Server Names Inside Private Network

    - by thyandrecardoso
    Our office has a private network, where any requests on a (pre-determined) public IP are forwarded to a private IP inside said network. On that private IP, we've got a server running several services, including HTTP servers, and SCM systems. We only control our private network, having no control on the public IP configuration. We bought a domain name, and pointed it to that public IP, so people can access our services from the outside. But, when inside the office, people can't use that DNS name, because the server and any other hosts inside the network share the same public IP! For desktops, inside the office network, dealing with names is really easy: one entry on the hosts file and we're done. However, for laptops, that keep going in and out, and need to access services inside the office, the naming is really annoying. I don't know the "standard" process for dealing with these kind of situations. I've considered installing BIND in the office, and make people configure their wireless and wired connections to use that DNS server. What is the correct approach in this situation? If using BIND (or any other DNS server) is the answer, how should I configure it so that people inside the office can use it to get our custom names, and get forwarded to the ISP DNS when trying to reach the internet?

    Read the article

  • Router stopping my python server

    - by drfrev
    This was originally posted in stackoverflow.com but it was suggested I move it here after it was realized it wasn't my code that was wrong. So my problem, very simply, is that I cannot get my computers that are connected to my router to communicate. example: If I ping a wireless computer I get no responce and the Request times out If I ping a computer wired to the modem directly it works fine. When I ping I use the local ip for each case. *if it helps my original post is here: http://stackoverflow.com/questions/12593024/python-cannot-go-over-internet-network/12593361#12593361 And some screen shots of different things are here: http://imgur.com/a/jUZ4G#3 thank you, any help is greatly appreciated. NOTE I am heading off to bed now, so I will respond around 6:00 AM EST if anyone posts some help

    Read the article

  • Iomega Home Media Network Hard Drive: Accesing the data in the disk?

    - by JJarava
    Hi all! I have an Iomega Home Media Network Hard Drive, 1TB, and lately I can't access the data on the drive. The shares (both built-in and created by me) are there, the security works, but when trying to access the data I get a "The network path was not found" message which is worrying, to say the least. I'd like to know if there is a way to get the data off the disks somehow, as some of the data in the drive (ie, pictures and videos of my 1.5 yrs old son) is hard if not impossible to find otherwise. Thanks a lot Javier

    Read the article

  • Persistent Issues on small business network using Cisco 871W and Catalyst Express 500

    - by Ben Campbell
    Being the most qualified (read: still not qualified) to solve our persistant network issues, I've turned to serverfault for guidance. I've done some searching, reading related documentation on cisco.com and tried a bit of troubleshooting. Here is the config: 100mb synchronous connection from a business internet provider (tested multiple times at 100meg at the source) Cisco 871W wireless point & router is where the WAN connection starts (this serves all our wireless). The only wired connection in the 871W is the Catalyst switch listed below. Cisco Catalyst Express 500 (24TT) is where all the wired connections terminate. About 20 Windows workstations and servers (AD/Webservers only). Some services in EC2 including mail and other web servers/apps. I've been TOLD cabling internally should be gigabit-ready. Here are the problems: generally slow download rates from the internet to the desktop/laptop frequent "page cannot be displayed" errors in browsers-sometimes 3 or 4 reloads are necessary... often times CSS wont load or other content requiring the browser to connect to a different server. slow speed within the LAN from workstation to workstation copying files. I would expect extremely fast data transfer workstation to workstation / server to workstation in this simple network. Several things I need to admit: I'm not primarily a network guy. Funding is relatively low, I need to be the guy that finds the solution. I understand most of the terminology and most of the technology. Implementation is where I fail due to lack of experience. Getting to the point: I'm wondering whether experienced network admins think that our small network should be sufficiently served with our current hardware if configured properly... or if we should purchase new equipment and start fresh? If starting fresh is the plan, whatever that new equipment may be is a likely different question entirely. If I haven't provided enough information, I will happily do some troubleshooting and update with the results. I have experience using wireshark and some other tools. Please let me know what you think would be most helpful and thanks in advance. EDIT: I forgot to add that the Cisco applicance will not finish loading the SDM Express console. It hangs every time at the "populating modules... DHCP". It eventually crashes and closes. I've rebooted the hardware and this still happens.

    Read the article

  • CPU & Memory Usage Log & Performance

    - by wittythotha
    I want to have an idea of the amount of CPU and memory that is being used. I have a website hosted using IIS, and have clients connecting to it. I want to find out the amount of load that the CPU, RAM and the network has when multiple clients connect. I tried out using tools like Fiddler, the inbuilt Resource Manager, and also some other applications I found on the internet. I just want to keep track of all these data in a file, so I can plot out a graph and find out how the CPU, etc. is performing. I read a few other posts, but didn't find anything that solves the problem. Is there good CPU / Memory Logging tool available, just to plot a graph of the usage, etc.? EDIT : I want to know of some tool that can save the performance details in a log file, so that I can use it to plot a graph, etc.

    Read the article

  • Slower wireless speed in Ubuntu 12.04 (64-bit) on Asus USB-N13

    - by PhantonTurtle
    I have an Asus USB-N13 which I use for wireless internet on my desktop. The download speed I get on Windows 7 (dual-boot) is 15.22 Mbps. On Ubuntu 12.04 (64-bit) I can only get 1.09 Mbps. I asked a question about this on the Ubuntu forums as well, but I did not get an answer. Here is the output from lsmod | grep rt which gives me, parport_pc 32866 0 rtl8192cu 103297 0 rtl8192c_common 75767 1 rtl8192cu rtlwifi 111202 1 rtl8192cu mac80211 506816 3 rtl8192cu,rtl8192c_common,rtlwifi cfg80211 205544 2 rtlwifi,mac80211 parport 46562 3 parport_pc,ppdev,lp I installed the drivers from Realtek (my chipset is Realtek, not Ralink) but that did not work.

    Read the article

< Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >