Search Results

Search found 9954 results on 399 pages for 'mean'.

Page 300/399 | < Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >

• My internet drops and will only reconnect if I troubleshoot it or restart my computer.

  - by Paul

  My internet loses its connection and at the same time, and my speaker seems broken if that happens and my mouse will not be smooth as it was before it happens. It already happened before and I didnt mind it. But now, it's happening literally all the time. After startup, my connection seems okay but after some few minutes, even without me doing something, my laptop will just lose its connection. It says that it is not connected and connections are available, but if I check if there are connections where I can connect it shows nothing. Even if, there is actually a wi-fi connection where my phone and other laptops connect. They dont seem to have problem with it. Just my laptop. After that happens, I usually restart my laptop but I discovered that troubleshooting it would somehow repair the problem, but not all the time. It says that restarting my wireless adapter do the job. Are there any long term fix? I mean that could last long or totally erase the problem? I have Atheros AR5B97 Wireless Network Adapter and Microsoft Virtual WiFi Miniport Adapter, both enabled. On the services, I have Wired AutoConfig and WLAN AutoConfig on Automatic. Aspire 4750, Windows 7 (x86)

  Read the article

• Turn off monitor (energy saving) while in text console mode (in Linux)

  - by Denilson Sá

  How to configure Linux text console to automatically turn of the monitor after some time? And by "text console" I mean that thing that you get on ctrl+alt+F[1-6], which is what you get whenever X11 is not running. And, no, I'm not using any framebuffer console (it's a plain, good and old 80x25 text-mode). Many years ago, I was using Slackware Linux, and it used to boot up in text-mode. Then you would manually run startx after the login. Anyway, the main login "screen" was the plain text-mode console, and I remember that the monitor used to turn off (energy saving mode, indicated by a blinking LED) after some time. Now I'm using Gentoo, and I have a similar setup. The machine boots up in text-mode, and only rarely I need to run startx. I say this because this is mostly my personal Linux server, and there is no need to keep X11 running all the time. (which means: I don't want to use GDM/KDM or any other graphical login screen) But now, in this Gentoo text-mode console, the screen goes black after a while, but the monitor does not enter any energy-saving mode (the LED is always lit). Yes, I've waited long enough to verify this. Thus, my question is: how can I configure my current system to behave like the old one? In other words, how to make the text console trigger energy-saving mode of the monitor? (maybe I should (cross-)post this question to http://unix.stackexchange.com/ )

  Read the article

• Virtual Fileserver

  - by Sergei

  Hi, We are planning to move our production servers to the datacenter and virtualize remaining servers in the process.Datacenter will have HP blades with vSphere on top.Currentliy we are using Celerra NS20 as fileserver.Since datacenter is using HP kit and EVA 4400 as SAN, we cannot have Celerra there, as EMC supoprt for Celerra does not work for non EMC array. I have searched for possible options and one of them was to have HP NAS blade X3800sb instead of Celerra.However this seems like overkill for me.We are only using Celerra for about 100 users and 50 servers and I think having X3800sb could be waste of resources. The other option would be to have a virtual fileserver as a part of vmware environment in datacenter.We only need CIFS to be provided.The only option I can think of is Windows Storage server.We had a bad expirience with Windows servers used as fileservers ( memory leaks one thing) in the past and this was one of the reasons we moved to Celerra. What are the other options?We need something as reliable as Celerra with as many options as possible.For example , Celerra has per folder quotas, deduplication, dynamic volume allocation, automatic failover, VTLU, replication. Also we would need to replicate NAS data to the failover site.We could use block level replication , SAN-to-SAN, but this would mean wasted bandwidth, as we need only subset of folders to be replicated.We used CA XSoft for windows servers in the past and Celerra has option for Celerra replication. Thank you very much in advance, Please ask me if I missed any details!

  Read the article

• What are the biggest, best CPUs that support Physical Address Extension?

  - by Giffyguy

  I'm looking for a CPU that will support PAE and fit into an LGA775 socket. This combination of technology is very much preferred for my current server hardware/software setup. My priorities in order of highest to lowest: PAE & LGA775 At least 1066Mhz FSB Largest CPU cache possible Multiple Cores if possible HyperThreading if possible Most other factors are of little-to-no consequence. I'm finding it very difficult to figure out what my options are. Intel doesn't have much useful information on PAE (since x64 is so dominant), and Wikipedia simply says that "PAE is provided by Intel Pentium Pro (and above) CPUs - including all later Pentium-series processors except the 400 MHz bus versions of the Pentium M." All of Intel's listed Pentium CPU's support Intel64, which makes me seriously doubt they will support PAE with a 32-bit OS. And Wikipedia's claim is so vague, I have no idea if they mean up-to-and-including the x64 Prescott CPUs. PAE is supposed to be an aspect of the x86 architecture, and I believe it is no longer supported in an x64 environment. Please correct me if I am wrong.

  Read the article

• how do you add an A record for a root domain

  - by nbv4

  this seems really simple, but I can't figure it out. I'm using xname.org since it's free and I own a bunch of domains spread over a few different registrars. The setup I desire is very simple: one A record that points the bare domain name to my server, plus a wildcard CNAME record pointing all subdomains to the same server. So if the user goes to domain.com it will point them to 285.24.435.75, if they go to www.domain, blah.domain.com, or any other sub domain, they'll get sent to 285.24.435.75. All the examples I read on the internet about setting up A records all have the A record set to a subdomain such as www. WWW is deprecated so I want to have noting to do with it. Currently my xname.org zone looks like this: $TTL 86400 ; Default TTL domain.com. IN SOA ns0.xname.org. nbvfour.gmail.com. ( 2010052503 ; serial 10800 ; Refresh period 3600 ; Retry interval 604800 ; Expire time 10800 ; Negative caching TTL ) $ORIGIN domain.com. IN NS ns2.xname.org. IN NS ns0.xname.org. IN NS ns1.xname.org. @ IN A 65.49.73.148 * IN CNAME domain.com The '@' symbol is something that the godaddy domain interface uses to mean "this root domain', but that may have been specefic to that interface and has no meaning here. Before I had a 'www' entry in the A rcords and it worked in the sense that I could ping 'www.domain.com' and it returned a response, but pinging the root domain 'domain.com' returned "no host found".

  Read the article

• Emptying Windows temp folder is a good idea?

  - by Siva Charan

  Am using DELL Inspiron with Windows 7. As far as I know emptying the windows temp folder would be good. But I faced a strange behaviour around 8 months back, when I clear my windows temp folder. The next day onwards, my laptop starting displaying daily one or other errors and one day OS got crashed. Till now I am not sure whether OS got crashed due to clearing the windows temp folder or something else is problem. Here Windows temp folder mean "C:\Windows\Temp" This is the behind the story. Today, this temp folder "C:\Windows\Temp" contains 102 GB Most of the space occupied by the files starts with etilqs_*.*. I came to know that these files are generated due to WD SmartWare. Now my problem is:- Actually I want clean up this folder, since it occupies lot of space. If I clean up "C:\Windows\Temp" folder, will my laptop face the same kind of problem which I faced earlier OR Any new problems will occur? Please suggest me a good solution.

  Read the article

• Possible DNS Injection and/or SSL hijack?

  - by Anthony

  So if I go to my site without indicating the protocol, I'm taken to: http://example.org/test.php But if I go directly to: https://example.org/test.php I get a 404 back. If I go to just: https://example.org I get a totally different site (a page about martial arts). I went to the site via https not very long ago (maybe a week?) and it was fine. This is a shared server, as I understand it, and I do not have shell access, so I'm limited to the site's CPanel to do any further investigations. But when I go to: example.org:2083 I'm taken to https://example.org:2083, which, if someone has taken over the SSL port, could mean they have taken over the 2083 part as well (at least in my paranoid mind). I'm made more nervous by the fact that the cpanel login page at the above address looks very new (better, really) compared to the last time I went to it over the weekend. It's possible that wires got crossed somewhere after a system update, but I don't want to put in my name username and password in case it's a phishing attempt. Is there any way to know for sure without shell access to know for sure if someone has taken over? If I look up the IP address for the host name, the IP address matches what I have on a phpinfo page I can get to over http. If I go to the IP address directly on port 2083, I get the same login mentioned above (new and and suspiciously nice). But the SSL cert shows as good when I go this route. So if that's the case (I know the IP is right, the cert checks out, and there isn't any DNS involved), is that enough to feel safe at that point of entry? Finally, if I can safely log in via the IP, does anyone have any advice on where to check first on CPanel for why the SSL port is forwarding to a site on karate? Thanks.

  Read the article

• Apache can't be restarted after changes to the configuration file

  - by Sharifhs

  Hello, I can't successfully configure the apache and php configuration files, can anybody help me in this way? Apache 2.2.16 (win32-x86-no_ssl.msi) was installed into “C:\Apache2.2 “location. Then PHP 5.3.3 (VC9 x86 Thread Safe) zip file was downloaded and extracted on “C:\php” location. From “C:\php” I renamed the “php.ini-development” file into “php.ini” “php.ini” file was opened with notepad, and modified as: doc_root = "C:\Apache2.2\htdocs" extension_dir = "C:\php\ext" The following lines were added to the Apache's configuration file “httpd.conf”: LoadModule php5_module "C:/php/php5apache2_2.dll" AddType application/x-httpd-php .php PHPIniDir "C:/php" N.B.: Thanks all for comments and answer, but I can't reply none your comments, I don't know why. May be I'm not privileged to put any comment as I'm new here (is it the case?)! That's why I'm to edit my post to reply you all. Tell me what can I do? @ jer.salamon: do you want me to post full httpd.conf file? It'll be longer then! @ davr: the server started first, but when I configured those files, its never started again @jer.salamon: did you mean keeping this way: doc_root = extension_dir = "ext" It not yet restared!

  Read the article

• Juniper’s Network Connect ncsvc on Linux: “host checker failed, error 10”

  - by hfs

  I’m trying to log in to a Juniper VPN with Network Connect from a headless Linux client. I followed the instructions and used the script from http://mad-scientist.us/juniper.html. When running the script with --nogui switch the command that gets finally executed is $HOME/.juniper_networks/network_connect/ncsvc -h HOST -u USER -r REALM -f $HOME/.vpn.default.crt. I get asked for the password, a line “Connecting to…” is printed but then the programm silently stops. When adding -L 5 (most verbose logging) to the command line, these are the last messages printed to the log: dsclient.info state: kStateCacheCleaner (dsclient.cpp:280) dsclient.info --> POST /dana-na/cc/ccupdate.cgi (authenticate.cpp:162) http_connection.para Entering state_start_connection (http_connection.cpp:282) http_connection.para Entering state_continue_connection (http_connection.cpp:299) http_connection.para Entering state_ssl_connect (http_connection.cpp:468) dsssl.para SSL connect ssl=0x833e568/sd=4 connection using cipher RC4-MD5 (DSSSLSock.cpp:656) http_connection.para Returning DSHTTP_COMPLETE from state_ssl_connect (http_connection.cpp:476) DSHttp.debug state_reading_response_body - copying 0 buffered bytes (http_requester.cpp:800) DSHttp.debug state_reading_response_body - recv'd 0 bytes data (http_requester.cpp:833) dsclient.info <-- 200 (authenticate.cpp:194) dsclient.error state host checker failed, error 10 (dsclient.cpp:282) ncapp.error Failed to authenticate with IVE. Error 10 (ncsvc.cpp:197) dsncuiapi.para DsNcUiApi::~DsNcUiApi (dsncuiapi.cpp:72) What does host checker failed mean? How can I find out what it tried to check and what failed? The HostChecker Configuration Guide mentions that a $HOME/.juniper_networks/tncc.jar gets installed on Linux, but my installation contains no such file. From that I concluded that HostChecker is disabled for my VPN on Linux? Are the POST to /dana-na/cc/ccupdate.cgi and “host checker failed” connected or independent? By running the connection over a SSL proxy I found out that the POST data is status=NOTOK (Funny side note: the client of the oh-so-secure VPN does not validate the server’s SSL certificate, so is wide open to MITM attacks…). So it seems that it’s the client that closes the connection and not the server.

  Read the article

• prevalent, recurring hardrive failure intel macbook from 2006/2007

  - by SimonSalman

  Hi, Long story: My MacBook's hard drive failed one year ago, just a month after its warranty ended or: a year and a month after I bought it. After about ten phone calls to Apple's service, they agreed to extend the warranty for another year, so that I got it replaced free of charge. In the mean time, I got to know that many MacBook users that experience/report hard drive failures. Every reported crash was preceded by a slowdown of system performance, an increased occurrence of the spinning beach ball wait courser, and frequent crashes of applications that used to run very robust until then. It happened (as far as I know) with MacBooks from 2006/2007. All these MacBooks additionally suffer from a recurring wearing down of their "top case". Many heavy users had to replace their HDDs three time since 2006/2007 resulting in an head crash, making it impossible to recover data (diagnosis of recovery specialists) in most but not all cases HDD was Seagate (doesn't necessarily have to be the cause, if majority of the MacBook charge contained Seagate drives) And right now (one year after my first disk crash), these symptoms are cumulating on my system, again ... Short version: prevalent hard drive failure on MacBook charge from 2006/2007 (i.e. 2.16 GHz Intel Core 2 Due) I am looking for any (preferable open source) tool for checking the hard drive condition, especially to detect the known "MacBook problem". So, that I can replace the disk on time. If any Mac user found a solution to prevent the repeated failure of heir hard drive, I would be very glad to get to known it. I really enjoy my old MacBook, but I hate to get interrupted every year by an HDD crash. BTW, the issue is already in discussion for a long time, but there seems to be no solution, so far. Thanks, Simon

  Read the article

• Increse gap (pause) between songs

  - by holms

  Hello, I googled a lot before asking. This is really a problem. I know that there's an option in preference to switch off cross fading, but this is not what I want to do. Cross fading doesn't add any gap at all. If there's no gap between two songs, so you won't hear any. I need a real GAP between song, I mean a REAL pause about 2 seconds. Why? My MD player can't handle songs if there are no gaps in line input. Even with 1 second gap MD records 2 songs as 1. Is there any software that can increase the gap in the playlist? I know that Winamp has a plugin for putting pauses between songs. Is there anything for iTunes or Mac OS X? Another work around is to add a 2 sec MP3 between each song in the playlist but this is really killing me to do. I'm more on lossless stuff, so .CUE files would be an option too (using XLD for converting)

  Read the article

• Setup 2003 R2 Radius server to work on vista/seven

  - by Fox

  Hi All, I'm currently trying to configure my 2003 R2 server RADIUS module to enable WIFI client to authenticate throught my Active Directory. The RADIUS server use MS-CHAP V2 as encryption method. I got several Access Point running DD-WRT, configured to use WPA2-Enterprise security that use Radius Server. Everything is setup, and almost working. When I say almost working, I mean, I can login using my AD Credential on my IPod or even on a MacBook running OS X, Windows XP also work with some little tweak in connection properties. The problem is Windows Vista or Windows Seven clients computers that are not inside domain. It doesn't work at all, it doesn't even prompt for user/password/domain. I already install the patch for IAS to make the certsrv compatible with Vista and Seven, but still doesn't work. Anyone ever encounter the same issue I have right now? I'm searching for a solution to this for several already and still not find anything. Looks like many people have the same issue too. Thanks all for you eventual answers.

  Read the article

• What is the IPv6 equivalent to IPv4 RFC1918 addresses?

  - by Kumba

  Having a hard time wrapping my head around IPv6 here. A lot of the lingo seems targeted at enterprise-level IPv6 deployments, discussing link-local, site-local, global unicast, scopes, etc. Not a lot of solid information on really small networks, like home networks. I want to check my thinking and make sure I am getting the correct translations from IPv4-speak to IPv6-speak. The first question is, what's the equivalent of RFC1918 for IPv6? Initial searches suggested there was no equivalent. Then I stumbled upon Unique Local Addresses (RFC4193), and that states that all ULA's should be assigned the prefix fc00, followed by a 40-bit random number in the routing prefix. This random number is to "prevent collisions when two IPv6 networks are interconnected" -- again, another reference to an enterprise-level function. If I have a small local LAN at home, numbered using 192.168.4.0/24, what's my equivalent in IPv6's ULA scope? Assuming I will never, ever, tie that IPv6 address into the real internet (a router will NAT & firewall it), can I ignore the RFC to an extent and go with fc00::4:0/120? It also seems that any address in fc00::/7 are to be globally routable. Does this mean I'll need extra protections so my router would not automatically start advertising these private IPv6 addresses to the world? Second question, what's this link-local thing? Reading suggests a default-assigned address in the fe80::/10 range that has the last 64bits of the address comprised of the interface's MAC address. Seems to be required, too, but I'm annoyed by the constant discussion of it in relation to enterprise networks. Third question, what is scope id for? Seems to be yet another term tossed around in relation to enterprise networks, especially when interconnecting them, but almost no explanation on the smaller home network level. Can I see a scope ID AND CIDR notation used together? I.e., fc00::4:0/120%6, or are scope IDs only supposed to be applied to a single /128 IPv6 address?

  Read the article

• Private IP getting routed over Internet

  - by WernerCD

  We are setting up an internal program, on an internal server that uses the private 172.30.x.x subnet... when we ping the address 172.30.138.2, it routes across the internet: C:\>tracert 172.30.138.2 Tracing route to 172.30.138.2 over a maximum of 30 hops 1 6 ms 1 ms 1 ms xxxx.xxxxxxxxxxxxxxx.org [192.168.28.1] 2 * * * Request timed out. 3 12 ms 13 ms 9 ms xxxxxxxxxxx.xxxxxx.xx.xxx.xxxxxxx.net [68.85.xx.xx] 4 15 ms 11 ms 55 ms te-7-3-ar01.salisbury.md.bad.comcast.net [68.87.xx.xx] 5 13 ms 14 ms 18 ms xe-11-0-3-0-ar04.capitolhghts.md.bad.comcast.net [68.85.xx.xx] 6 19 ms 18 ms 14 ms te-1-0-0-4-cr01.denver.co.ibone.comcast.net [68.86.xx.xx] 7 28 ms 30 ms 30 ms pos-4-12-0-0-cr01.atlanta.ga.ibone.comcast.net [68.86.xx.xx] 8 30 ms 43 ms 30 ms 68.86.xx.xx 9 30 ms 29 ms 31 ms 172.30.138.2 Trace complete. This has a number of us confused. If we had a VPN setup, it wouldn't show up as being routed across the internet. If it hit an internet server, Private IP's (such as 192.168) shouldn't get routed. What would let a private IP address get routed across servers? would the fact that it's all comcast mean that they have their routers setup wrong?

  Read the article

• Windows 7 mapped drive kicking off OS X users

  - by Collin White

  I've mapped a network drive on my Windows 7 PC at my office. The windows machine has a few TB of storage that is being accessed by my development team (all running mac os 10.7). The share seems to work fine for a little while but will timeout and kick the mac users off and sometimes disallows a connection on the next attempt. Restarting the windows machine fixes the problem. I've tried this tutorial as well as setting the maximum session length in the Local Security Policy section to 99999 (I discovered 0 did not mean unlimited, only a 'reasonable ammount of time') anyway, the setting is now for ~208 days which is sufficient (see attached). I'm having trouble debugging this in general so if anyone has some pointers I'm all ears. This is a intermittent issue which in my opinion are the hardest kinds to debug. If anyone knows of how I might monitor connections from the PC that would also be pretty cool. Previously the files were hosted on a mac mini and everything was working just fine (the mini just didn't have the ability for the storage capacity we needed) so I believe it is some windows setting that is kicking users off. Anyway, thanks for reading.

  Read the article

• Disabling drop shadows around windows or the menu bar

  - by Lri

  Nocturne can disable most shadows, but only in night mode. There's an annoying flash whenever it switches to night mode. (Eg when it's launched.) Also, it doesn't remove the shadow on the menubar. Sympa at MacThemes forums has posted a .psd file with a layer that cancels out the shadow under the menu bar. However it only works if that area of the desktop picture has a low enough brightness. Applications that cover the desktop (like DeskShade) also cover the menu bar's shadow. It's not a real solution though. Unsanity's ShadowKiller stopped working in 10.5. (The website still says NOT compatible with Mac OS X 10.6 Leopard. ;)) WindowShade X doesn't have any shadow-tweaking features anymore. Being able to decrease the shadow radius would be fine as well. osx - How do I decrease the window shadow in Mac OS X? - Super User doesn't have any solutions though. No, I don't mean defaults write com.apple.screencapture disable-shadow -bool yes. This seems like something that might just be possible without any extra applications. Or at least something that other applications besides Nocturne should support. So does anyone know any better solutions?

  Read the article

• Sending mail through local MTA while domain MX records point to Google Apps

  - by Assaf

  My domain's email is managed by Google Apps, so that domain users get Gmail and Calendar, etc. But I also want to be able to send applicative notifications to users outside the domain via email (e.g. "some commented on your post", and so on). However, if I try to send email through code I get blocked by Gmail after a few emails. I send marketing email through MailChimp, to minimize the risk of appearing as spam to my users (one-click unsubscribe, etc.). But I can't send applicative message in this way. I want to install a local MTA (my server runs Ubuntu), but I'm not sure what anti-spam measures I need to implement so that receiving MTAs don't think it's a spam server. What's stopping anyone from setting up a mail server and sending emails using my domain name? AFAIK it's the DNS records that show the MTA's address actually belongs to the domain. But my understanding of this is rather superficial, so someone please correct me if I'm wrong. But what sort of DNS configuration do I need to put in place so that I don't get blacklisted (assuming I don't actually spam anyone)? The MX records already point to Google, and I'd like to keep it this way. So do I just need to define an A record for my internal mail server? Should it show email as coming from a sub-domain, so as not to conflict with the bare domain being managed by google? Edit: Does the following SPF record make sense if I want email from my domain name to be sent by either google's servers or any server with a dns name ending with mydomain.com? "v=spf1 ptr mx:google.com mx:googlemail.com ~all" How should I set up reverse DNS for my server? If I have an A record that points mailsender.mydomain.com to my MTA's ip address, does it mean that reverse lookup will only allow emails sent from [email protected]?

  Read the article

• Get Internal IP Address From DHCP Hostname

  - by ell

  I would like to try and get an internal ip address of one of the computers on my network. The reason for this is I have a little home server box downstairs but every time I want to SSH into it I have to open my router configuration and go on the DHCP client table and look at the IP address. For example I would like to be able to go ssh ell-sever instead of ssh 192.168.1.105 or whatever it happens to be. My network configuration is like so: Router downstairs that is connected to the Internet and is running a DHCP server My server computer (ell-server) is a headless pc connected to the router via ethernet cable. Running Ubuntu 11.04 Server Edition My laptop upstairs (ell-laptop) that is running Ubuntu 11.10 Desktop Edition connected wirelessly Other (irrelevant) computers - 2 x Windows XP, 1 x Xubuntu - all connected with cables. (It seemed to me the method of connection isn't useful information but I put it in anyway - just in case. If I have missed any information please tell me) Do I have to run a DNS server on one of my computers? If so which one? And does that mean I will have to run a DDNS client on each computer? Thanks in advance, ell.

  Read the article

• esxi 5 monitoring

  - by user134880

  I'm new to esxi/vmware world. Have few question about monitoring esxi host. Now I'm using trial versian esxi 5.1 I can see performance charts in vShpere client. Cool. But I want to export this raw data (raw - I mean cvs,txt or some format which I can parse later) to other server to be able to parse this data later and create custom charts. (please do not advise to try vCenter, I need custom charts etc.) I could run esxtop in batch mode and use this data... But... How does vShpere client performance charts work? Where client takes data for charts? So if I will use esxtop batch mode it will add extra load to server. Is it possible to use same source as vSphere client use for charts? There is /var/lib/vmware/hostd/stats/hostAgentStats-20.stats file. Its looks like it is binary format. As I understood it is exactly data which I need?!?! Any ideas how to parse it? Thanks! PS: maybe some one know where to find, if there is one, info about processes running on esxi host?

  Read the article

• Integrating Nagios with a ticketing system/incident mnagement system

  - by sektor

  Is there a free ticketing system/incident management system which will help me in achieving the following? 1) If a service goes down then Nagios alerts the on-duty staff and pushes the status to some backend or DB as a ticket, say the initial status is "New". 2) The on-duty staff logs in through a frontend and acknowledges the new ticket by marking it as "In progress", so now the status of the ticket changes from "New" to "In progress". 3) If even after "n" number of minutes no person from on-duty staff has changed the ticket status to "In progress" then Nagios alerts the next level of contacts. Although if the on-duty staff has acknowledged the ticket then there is no need to alert the next level. 4) When the service comes up Nagios closes the ticket by marking it "Closed" Now I already have Nagios monitoring set up and currently it alerts by sending text messages and mails, what I'm looking for is some framework which only escalates the issue(alerts the second level) if the first level(on-duty staff) fails to respond to the initial alert. By "responding to the alert" I mean, the on-duty staff can login via some frontend and basically change the status to something like "Acknowledged" or "In progress".

  Read the article

• Trouble getting latest version of Git

  - by TheMethod

  I am using Ubuntu 10.04 LTS. I'm looking at using git as source control for personal projects and Github as a remote repository. I was having trouble pushing a commit to my remote github repo getting the following error message: The requested URL returned error: 403 while accessing https://github.com/Jstall/helloworld.git/info/refs When I did some digging I found that the problem could be me not having the latest version of Git. When I did a --version I found that I have version 1.7.0.4 locally. So I tried to update git using: sudo apt-get install git but get the following error: Reading package lists... Done Building dependency tree Reading state information... Done Package git is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package git has no installation candidate I've tried running: sudo apt-get update and trying again but it didn't seem to make a difference. I'm not sure if it's relevant but I'm also getting a couple of 404's when I run update: Err http://wine.budgetdedicated.com edgy/main Packages 404 Not Found Fetched 4,117B in 0s (5,142B/s) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/edgy/universe/binary-i386/Packages.gz 404 Not Found [IP: 91.189.91.15 80] W: Failed to fetch http://wine.budgetdedicated.com/apt/dists/edgy/main/binary-i386/Packages.gz 404 Not Found I'm not sure when I should try next. Could anyone suggest a course of action to get this resolved? Any advice would be appreciated. Thanks much!

  Read the article

• Same netmask or /32 for secondary IP on Linux

  - by derobert

  There appear to be (at least) two ways to add a secondary IP address to an interface on Linux. By secondary, I mean that it'll accept traffic to the IP address, and responses to connections made to that IP will use it as a source, but any traffic the box originates (e.g., an outgoing TCP connection) will not use the secondary address. Both ways start with adding the primary address, e.g., ip addr add 172.16.8.10/24 dev lan. Then I can add the secondary address with either a netmask of /24 (matching the primary) or /32. If I add it with a /24, it gets flagged secondary, so will not be used as the source of outgoing packets, but that leaves a risk of the two addresses being added in the wrong order by mistake. If I add it with /32, wrong order can't happen, but it doesn't get flagged as secondary, and I'm not sure what the bad effects of that may be. So, I'm wondering, which approach is least likely to break? (If it matters, the main service on this machine is MySQL, but it also runs NFSv3. I'm adding a second machine as a warm standby, and hope to switch between them by changing which owns the secondary IP.)

  Read the article

• Decyphering Seagate drive model numbers?

  - by Stefan Lasiewski

  I'm comparing Seagate's Enterprise and Desktop drives for a variety of old and new servers. These servers come from different generations, so options like size (73GB, 2TB) and interface (SATA vs SAS 3.0Gbps vs SAS 6Gbps vs SCSI Ultra320) are widely variable. I'm trying to compare the sizes, speeds and interfaces, but I'm getting thrown off by different models. Also, their website is not the best. Does anyone know of a documented explanation of the Seagate model numbers? And is there a single spreadsheet which compares the features for all drives (or all 'Enterprise' drives?). Seagate drives have model numbers like this: Model ST3600057SS 6-Gb/s SAS 600 GB None at Cheetah® 15K Hard Drives Model ST373455LW Ultra320 SCSI 73.4 GB 68-Pin LW at Cheetah® 15K Hard Drives Model ST32000644NS SATA 3Gb/s 2 TB None at Constellation™ ES Hard Drives Model ST973452SS 6-Gb/s SAS 73 GB None Savvio® 15K Hard Drives Model ST9200011FS SATA 3Gb/s 200 GB Pulsar™ Solid State Drives I understand the model numbers read something like this: ST - SOMETHING1 - SIZE - SOMETHING2 - INTERFACE Where the fields mean something like this: ST : For 'Seagate'? 'Seagate Technoligies'? SOMETHING1 - This field has number, but I'm not sure what that represents. SIZE - Size in Gigabytes. This is a number like '73' or '300' or '2000' SOMETHING2 - This field also has a number, but I'm not sure what it means. INTERFACE - This field seems to indicate the Interface. 'SS' means SAS, 'FC' means Fibre Channel, but I don't see how to distinguish between 6Gbps SAS and 3Gbps SAS, or different SATA or FC speeds. I don't see a field which indicates the RPM (15K , 10K, 7.2K) etc. Is this part of the model number?

  Read the article

• Feasibility of Windows Server 2008 DFS replication over WAN link

  - by CesarGon

  We have just set up a WAN link that connects two buildings in our organisation. The link is provided by a 100-Mbps point to point line. We have a Windows Server 2008 R2 domain controller on each side of the link. Now we are planning to set up DFS for file services across the organisation. The estimated data volume is over 2 TB, and will grow at approximately 20% annually. My idea is to set up a file server in each building and install DFS so that all the contents stay replicated over the 100-Mbps link. I hope that this will ensure that any user will be directed to the closest (and fastest) server when requesting a file from the DFS folders. My concern is whether a 100-Mbps WAN link is good enough to guarantee DFS replication. I've no experience with DFS, so any solid advice is welcome. The line is reliable (i.e. it doesn't crash often) and our data transfer tests show that a 5 MB/sec transfer rate is easily achieved. This is approximately 40% of the nominal bandwidth. I am also concerned about the latency. I mean, how long will users need to wait to see one change on one side of the link after the change has been made on the other side. My questions are: Is this link between networks a reliable infrastructure on which to set up DFS replication? What latency times would be typical (seconds, minutes, hours, days)? Would you recommend that we go for DFS in this scenario, or is there a better alternative? Many thanks.

  Read the article

• conflicting info about the running kernel version in FreeBSD

  - by John

  I asked a related question about uname before, now want to ask from another angle because the following simple yet obvious conflicting outputs may mean there is something many people did not think of (me included). I'm running FreeBSD 9 RELEASE, please see the following commands: # sysctl kern.bootfile kern.bootfile: /boot/kernel/kernel # strings /boot/kernel/kernel |grep RELEASE|grep 9 @(#)FreeBSD 9.2-RELEASE-p7 #0: Tue Jun 3 11:05:13 UTC 2014 FreeBSD 9.2-RELEASE-p7 #0: Tue Jun 3 11:05:13 UTC 2014 9.2-RELEASE-p7 The above kernel file suggests the running kernel is 9.2-RELEASE-p7. But... # dmesg Copyright (c) 1992-2012 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.1-RELEASE #0 r243825: Tue Dec 4 09:23:10 UTC 2012 ... # uname -a FreeBSD localhost.localdomain 9.1-RELEASE FreeBSD 9.1-RELEASE #0 r243825: Tue Dec 4 09:23:10 UTC 2012 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 So dmesg and uname says it's 9.1-RELEASE. I also did an extensive find / -type f -exec grep -l "9.1-RELEASE" {} \; but found no possible kernel file that contains 9.1-RELEASE. What could lead to the above conflict, and what kernel I am actually running? Please note I run RELEASE and ran freebsd-update to do binary update, so no compiled kernel is involved. And I have rebooted multiple times after freebsd-update. And the system is not in jail etc, just the only system on that computer.

  Read the article

< Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >