Search Results

Search found 21678 results on 868 pages for 'network traffic'.

Page 300/868 | < Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >

• Why is my router not routing?

  - by dwj

  Starting a week and half ago my router stopped working with my cable modem. I went to sleep with it working and woke up with it not. I swapped in another router and am still having issues; I was gone for 10 days so now I'm back to trying to figure it out. While I was gone I left everything (cable modem, router, and computer) powered off. My setup: Comcast Ambit cable modem (from Comcast) Netgear WGR614 v4 router -- replaced with Linksys WRT54GS v1.1 Windows XP SP3 other computers, all currently unplugged The modem is using the firmware (ver 2.105.2001) provided by Comcast; hardware version 1.3 The Linksys router is using FW ver 4.71.4 (latest for this release of HW), factory defaults I am only using the wired connections; no wireless. I have swapped out all of the cat5 cable. If I plug my computer directly into the cable modem, I can ping by name or number. Everything works perfectly. If I plug my computer into the router and the router into the modem, I cannot access anything outside of my local network. This is the exact setup I've used for the past 5 years; there were no changes in the past year. Now here's the interesting part: I can log into the Linksys router and get status information from it; everything appears good. Using the Diagnostics, I can run ping and traceroute to any site on the internet. These work perfectly. From my computer, I can ping the router and the modem. However, I cannot ping anything on the internet by with name or number. If I plug in another computer, I can ping it successfully. I've included two transcripts below that show these two attempts. Addresses, DNS, gateways, etc. look good. I cannot access the internet through either router. I am at a loss here. Suggestions? Help! Computer to Router to Cable Modem C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:21:55 PM Lease Expires . . . . . . . . . . : Tuesday, March 23, 2010 10:21:55 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Ping request could not find host google.com. Please check the name and try again . C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\ Computer to Cable Modem Directly C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 DHCP Server . . . . . . . . . . . : 68.87.76.10 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:18:50 PM Lease Expires . . . . . . . . . . : Monday, March 22, 2010 11:12:31 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Pinging google.com [74.125.19.99] with 32 bytes of data: Reply from 74.125.19.99: bytes=32 time=20ms TTL=55 Reply from 74.125.19.99: bytes=32 time=17ms TTL=55 Reply from 74.125.19.99: bytes=32 time=28ms TTL=55 Reply from 74.125.19.99: bytes=32 time=18ms TTL=55 Ping statistics for 74.125.19.99: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 17ms, Maximum = 28ms, Average = 20ms C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=17ms TTL=55 Reply from 74.125.19.104: bytes=32 time=16ms TTL=55 Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 16ms, Maximum = 18ms, Average = 17ms C:\

  Read the article

• Stunnel delaying boot

  - by Onitlikesonic

  My stunnel implementation works fine when the network is plugged in but it takes an awful amount of time, which delays the whole boot process, when there is no network connected to the machine. As extra information: I'm using "delay=yes" I'm using an fqdn (e.g: stunnel.mydomain.com) for the connections Using ubuntu but this also happened with centos5 previously How can this be avoided or a timeout specified? edit: doing an strace as suggested by symcbean shows the following (including the last part where it hangs): [...] --- SIGCHLD (Child exited) @ 0 (0) --- rt_sigreturn(0x11) = 0 close(3) = 0 wait4(-1, [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0, NULL) = 6039 clone(child_stack=0, flags=CLONE_CHILD_CLEARTID|CLONE_CHILD_SETTID|SIGCHLD, child_tidptr=0x7ff9ce0c79d0) = 6046 wait4(-1, [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0, NULL) = 6046 --- SIGCHLD (Child exited) @ 0 (0) --- rt_sigreturn(0x11) = 6046 write(1, "[Started: /etc/stunnel/stunnel.c"..., 37) = 37 write(1, "stunnel.\n", 9) = 9 exit_group(0) = ? [...] stunnel hangs in this line: wait4(-1, and when i plug in the network cable it continues to show [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0, NULL) = 6046

  Read the article

• Acer Aspire 7739G-6647 won't connect to the internet

  - by Nux

  Acer Aspire 7739G-6647, it belongs to a family member. I reinstalled the chipset, LAN drivers, ethernet controllers, etc. I'm positive it's not my router or modem or anything like that. I have other laptops running on the network, this one just has some strange issue. For some reason, it's saying "Work Offline" is enabled when I open Windows Media Player, and the PC seems to be connected to the network, but on the graphic in networking, it doesn't show the connection between the network and the internet. Could anyone try to state any possible reason for this issue? Any help is appreciated.

  Read the article

• cloning mac address of physical server converted into vmware server

  - by user24981

  We've recently converted a physical Windows Server 2003 into vmware using P2V. However, one of the pieces of software on the 2003 machine are still looking for the old server's network MAC address in order to run. I've read several articles where it's discussed that you can modify the last part of the generated address and set it to static, but I need to clone the whole mac address to mimic the one in the old server. We're running CentOS and VMware server 2.0 as the host system. I was told that maybe adding in a second network card in the host and setting the virtual system's nic to that card instead of "bridged" would allow me to edit the vmx file and clone the whole MAC address. I can't use the old network card from the physical server because it's ISA and our new bus is PCI Any ideas? Thanks, Mike

  Read the article

• Unable to connect to wireless internet(wifi) through KDE plasma desktop

  - by Mohammed Arafat Kamaal

  I installed the KDE plasma desktop through Ubuntu software center. I am on Ubuntu Lucid Lynx. After the install, Im unable to connect to my wifi connection in the KDE session. But I can connect to my wifi perfectly through GNOME session. I've tried a lot without much success. Also KDE doesn't store my password correctly and keeps prompting for authorization again and again. Some of the things that I noticed. Network is detected, Network name and strength is also displayed. Other characteristics also appear properly. When the credentials are supplied, it accepts them and continually displays the message "Setting network address". However this process never succeeds. At this stage the password is repeatedly asked many times but the connection is never established. Some of the other things that I did, I have also tried other things like restarting my modem and the computer. That didn't work. I tried to restart nm-applet and KNetworkManager. That didn't work either. ifconfig display all my interfaces and Mac addresses correctly. Since its working fine GNOME the drivers are fine. This is sure a KDE specific issue. Other threads related to this on the interwebs don't offer much information either. Please share a solution for this.

  Read the article

• Cannot enable wireless on an Intel WifiLink 1000 on an Lenovo Ideapad z570

  - by Brij

  I am using the ubuntu 11.10 on lenovo ideapad z570. My wireless internet is not working. I have ensure that wireless switch is on. Windows 7, wireless works great.However ubuntu 11.10 is not allowing me to enable wireless connection. I have run the following command and here is the status. sudo lshw -class network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:1c:a4:a4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:42 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: f0:de:f1:64:b6:62 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff Here is rfkill list all output: rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Note : Windows 7, wireless card property shows that Intel WifiLink 1000 BGN. Could someone help me to fix this issue.

  Read the article

• How to setup a 1 way trust, Windows Server 2008 R2

  - by MichaelOz

  I am on my home network and connect to workplace via a VPN. I have a DC on my home network (DC1 , domain = home). How can I setup a 1 way trust, so that I am able to run executables, such as SQL Management Studio using RunAs - then type in credentials for work domain? First question is, will a 1 way trust solve this, and can I set this up without bothering a network admin at workplace (assuming I have a domain account with enough permissions on work domain) If yes - any good step by step guide to setup 1 way trust? Server is Windows Server 2008 R2. As mentioned its DC running DNS Role too. Thanks in advance

  Read the article

• Missing eth0 configuration file

  - by Godric Seer

  I have two servers both running Scientific Linux 6 on the same network. Since I want SSH access to both of them, I want to give them both static IPs so I can setup port forwarding and not worry how my router assigns local IPs. I found that I need to edit the configuration file /etc/network-scripts/ifcng-eth0, however that file does not exist. The network card works fine, and I am able to ssh as long as I access the router and find the local ip. Can I simply make my own configuration file, or did I miss some step in configuring the system that I need to complete?

  Read the article

• Can't get bridged networking to work between linux guest virtual machine and Mac host

  - by tgoneil

  I'm trying to establish bridged networking from linux mint vsn 12 in virtualbox to a Mac Lion host. Mac config: Network setting: en3 configured by DHCP Sharing setting: Internet Sharing selected, Share connection from en3 to computers using en3 Virtualbox Linux setting: Network setting: Bridged Adapter, Name: en3 I can ping from host (192.168.2.1) to guest (192.168.2.2) and guest to host, but I Cannot ping from the Linux guest to the outside world. Connection in host is up, because I can ping from the Mac host to the outside world. Something else that's seems weird to me, in the Mac Network setting, the IP Address generated by DHCP says 169.254.243.185. What the heck is that?? When I open a terminal up in the Mac, however, ifconfig shows its en3 inet address as 192.168.2.1.

  Read the article

• Problem with Lenovo x200s Wifi under Ubutu Karmic

  - by oneself

  Hi, I have just gotten my Lenovo X200s laptop, and I am install Ubuntu 9.10 Karmic on it. The installation went through without a hitch, but I can't get my wifi to work. lspci | grep Network Produces the following results: 00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03) 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10) The weird part is that when I turn the wifi hardware stitch on and off on the side of the laptop, I get the following printed in /var/log messages: Dec 30 23:24:48 temp-laptop kernel: [ 213.432302] usb 4-2: USB disconnect, address 2 Dec 30 23:24:52 temp-laptop kernel: [ 217.276310] usb 4-2: new full speed USB device using uhci_hcd and address 3 Dec 30 23:24:52 temp-laptop kernel: [ 217.441759] usb 4-2: configuration #1 chosen from 1 choice Does Ubuntu think my wifi card is a USB device? Am I missing some driver? What can I do to fix this? Please, help!

  Read the article

• How do I built a DIY NAS?

  - by Kaushik Gopal

  I'm looking for good, detailed instructions on how to build a DIY NAS (Network Access Storage). I'm planning on doing it cheap (old PC config + open source software). I would like to know: What hardware I need to built one What kind of hard-drive setup I should take (like RAID) Or any other relevant hardware related advices (power supply, motherboard etc...) What software I should run on it, both what OS and software to manage the contents effectively So the NAS is recognizable and accessible to my network I can make sure my Windows computers will recognize it (when using Linux distro's) I can access my files from outside my network I already did a fair bit of searching and found these links, but while these links are great they delve more on the hardware side. I'm looking for more instructions in the software side. Ubuntu Setting up a Home NAS DIY NAS Smackdown How to Configure an $80 File Server in 45 Minutes FreeNAS Build a NAS Device With an Old PC and Free Software Build Your Own NAS Device

  Read the article

• cPanel's Web Disk - Security issues?

  - by Tim Sparks

  I'm thinking of using Web Disk (built into the later versions of cPanel) to allow a Windows or Mac computer to map a network drive that is actually a folder on our website (above the public_html folder). We currently use an antiquated local server to store information, but it is only accessible from one location - we would like to be able to access it from other locations as well. I understand that folders above public_html are not accessible via http, but I want to know how secure is the access to these folders as a network drive? There is potentially sensitive information that we need to decide whether it is appropriate to store here. The map network drive option seems to work well as it behaves as if the files are on your own computer (i.e. you can open and save files without then having to upload them - as it happens automatically). We have used Dropbox for similar purposes, but space is a issue with them, as is accountability and so we haven't used it for sensitive information. Are there any notable security concerns with using Web Disk as a secure file server?

  Read the article

• Asus Eee PC 1000HE wireless woes

  - by Vladimir Noobokov

  Ever since I have upgraded my Asus Eee PC 1000HE from Lucid 10.04 to Precise 12.04 I have been having issues with my wireless connections. At first I had wireless dropouts: I would be able to start using wireless, but then after a few minutes the wireless would stop working even though I was still connected to the network. Lately things turned worse: while I connect to my wireless network, it just never works. I tried all sorts of solutions on offer here and in other forums but none worked. At best I got the wireless to work up until I rebooted, at which point I would get the same symptoms again: the wireless network is there, but it's not really working. By now I tried so many different "solutions" I don't know where to start describing them; I have also reinstalled 12.04 several times, enough to make me lose faith in Ubuntu. Help here looks like my last resort. For the record, my Asus Eee PC 1000HE is equipped with an Atheros wireless card. I have reinstalled 12.04, ran all the suggested updates, and receive the following response when I type iwconfig in the terminal: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Arsenal" Mode:Managed Frequency:2.452 GHz Access Point: 00:04:ED:48:67:89 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-29 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:27 Invalid misc:57 Missed beacon:0 eth0 no wireless extensions. Thanks in advance for any help that might be offered.

  Read the article

• Internet not working on a VirtualBox Linux machine

  - by mtahmed

  I installed VirtualBox on a Windows 7 PC and installed Xubuntu (Ubuntu with XFCE) on it. Now on the Windows, I am connected to the internet through a LAN which automatically authenticates to connect to the network(because its my work computer). I have also installed the guest additions on this virtual machine (Xubuntu). I tried both NAT and bridging to set up internet connection but I still cannot connect to the internet. For NAT: The browser doesn't say website not found but it keeps trying to load it forever and the network status monitor (the one provided by VirtualBox) doesn't show any green light (no incoming packets). For Bridging: Same as for NAT but the network status monitor shows incoming packets and outgoing packets. But internet still doesn't work. I tried a lot of different things but none worked.

  Read the article

• Configuring a Genius GW-7200 Access Point

  - by alex

  I came across an access point we had a few years ago. I'm now trying to get it set up to work on our network. here are a couple of pictures: http://twitpic.com/194u06/full http://twitpic.com/194u0v/full I have plugged this into our network via the network port on the back. I set up a DHCP reservation, based on the MAC address on the back of the access point, however I cannot ping it, nor access the web interface. I've held down the reset button for 10 seconds, to see if that would do anything. Google doesn't come up with anything on the matter :-(

  Read the article

• Win7 to Win7 Remote Desktop Not working, Xp to 7 working fine

  - by vlad b.

  Hello, I have a small home network and recently i tried to enable remote desktop for one of the pc's. I have a mix of Windows 7, Windows Vista and Xp runing alongside ubuntu, centos and others (some virtual, some real). I have a few Windows 7 pc`s that can be connected to using remote desktop from inside and outside the network (port redirects on routers, etc, etc) and some Xp ones. The trouble is when i tried to do the same thing to a Win7 laptop i discovered i can't connect to it from another win7 pc inside the home network. To sum it up Working: xp -- win7 not working: win7 -- win7 What i tried - disable and enable remote desktop (my computer - remote settings) - removing and adding users to the remote settings window - adding a new user to the machine, administrator or 'normal' user - checking the firewall settings on the machine and set 'allow' to remote desktop for both 'home/work' and 'public'networks Any tips on what should i do next? It displays ' .. secure connection' and after that the window with 'Your security credentials did not work' and it lets me try again with another user/password..

  Read the article

• What type of VPS stats should I look for?

  - by Dave

  I have a few websites that average a total of 10,000 uniques a day across my network. I also have a few mobile apps that pull xml data maybe 5,000 calls a day. My sites aren't anything major just a few wallpaper websites and few other small sites, nothing real database intensive. I currently own a dedicated server and I feel like it's overkill for my network. I'm looking into getting a Virtual Private Server (VPS). I was just wondering what kind of stats I should be looking for to support my network of sites. Thanks

  Read the article

• Rip authedicatation from LDAP to Local

  - by oxinabox

  We are taking a small portion of out network offline, and running a separate network using that portion. (By small portion I mean 2 servers, that will be connected to 30 odd boxs that aren't usually part of our network, and don't need to authenicate) I intend to create a VM on one of the servers to provide general user services, and IRC server, remote shell etc. And I would like the users to be able to use there usual server log in details. Problem is the LDAP server that normally checks those details is not one of the severs. So I need to be able to some how take their details off LDAP and put them on the the server that is coming. One suggestion I had was to set a LDAP server on the VM locally, and clone the LDAP database onto it (using something called slapcat) is this the best way? Or can I I change the LDAP data into local authentication data?

  Read the article

• Windows Storage Server 2003 R2 RDP Disconnection

  - by Antitribu

  I am unable to remote desktop to our Windows Storage Server 2003 R2 machine. There are a few people about with similar issues but no answers around. Symantec End Point is installed but no network protection. Using rdesktop in Linux I receive: ERROR: send: Connection reset by peer NOT IMPLEMENTED: PDU 12 ERROR: Connection closed Where the "PDU XX" number changes on each connection. In windows using the latest mstsc I receive: The connection was lost due to a network error. Try connecting again. If the problem persists, contact your network Administrator. Any ideas?

  Read the article

• Need assistance setting up Linux Router with 2 public lans

  - by user195407

  I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

  Read the article

• iptables forward rule not working in openwrt

  - by Udit Gupta

  I am trying to apply some iptables forwarding rules in openwrt. Here is my scenario - My server has two cards ath0 and br-lan. br-lan is connected to internet and ath0 to private network. The other m/c in n/w also has ath0 that connects with this server's ath0 and they are able to ping each other. Now, I want other m/c in network to use internet using br-lan of server so I thought of using iptables forwarding rule- Here is what I tried - Server : $ ping 1.1.1.6 // <ath0-ip of client> works fine $ iptables -A FORWARD -i ath0 -o br-lan -j ACCEPT $ /etc/init.d/firewall restart Client : $ ping 1.1.1.5 // <ath0-ip of server> works fine $ ping 132.245.244.60 // <br-lan ip of server> (not working) I am new to iptables stuff and openwrt. What I am doing wrong here ?? Any other help if anyone could suggest for my scenario Edit- m/c - machine n/w - network

  Read the article

• Apache server in raspberry PI not visible from outside( public IP)

  - by Kronos

  I have made a fresh install of Arch Linux ARM into a Raspberry PI and I mounted there a LAMP, all fresh. I have another Arch(x86) in my laptop with Apache also there, and as far as I know, two web servers cannot run in the same network segment so, the problem is as follows. I my laptop, having Apache running, if I enter via the public ip of my network everything turns ok and I can see my website but, (obviously turning this server down) if I enter from the public IP with the Apache running in the raspberry pi( yes, only that Apache running) i cannot see my website in there. Also, if I access via local network it is a normal success, I can see my website. So, I can enter my raspberry website only via local but in my other web server i can enter it via local and public. I have the same conf files in both of them so what is the difference? I was planning in making the rpi as a development server. Thanks in advance

  Read the article

• auto-summarization: classful vs classless routing protocols

  - by yorble

  Suppose a router R1 is directly connected to the following subnets: 10.1.0.0/24 10.1.1.0/24 10.1.2.0/24 10.1.3.0/24 If it is running RIPv1, it will advertise: "i have the network 10.0.0.0" (implicitly understood by receiving RIPv1 routers as 10.0.0.0/8 because the protocol is classful) but suppose we changed the routing protocol to RIPv2 and turned ON auto-summarization. Would it behave in the same way? Would it advertise: "i have the network 10.0.0.0" (advertised WITHOUT subnet mask, and implicitly understood by other routers as 10.0.0.0/8) OR would it auto-summarize in a non classful way like: "i have 10.1.0.0/22" (advertised as network id and subnet mask pair) In other words, does turning on auto-summarization in RIPv2 (or other classless routing protocols) cause it to auto-summarize in a classful manner or simply auto-summarize classlessly to the best of its ability?

  Read the article

• vSphere ESX 5.5 hosts cannot connect to NFS Server

  - by Gerald

  Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

  Read the article

• Can't the NetworkManager applet to appear in the Gnome panel in Ubuntu

  - by Nate

  I have researched this problem extensively and I can't seem to find an answer. In Ubuntu 10.04 LTS, I want to connect to my VPN through the NetworkManager applet. I installed all the network manager packages, including the gnome client. I understand I need to add the "Notification Area" to the panel, which I have done. I checked that the NetworkManager is running: nate@nate-desktop:~$ service network-manager status network-manager start/running, process 763 In /etc/NetworkManager/nm-system-settings.conf, I have added managed=true (don't know if this matters, but I saw it suggested on one forum): nate@nate-desktop:~$ more /etc/NetworkManager/nm-system-settings.conf # This file is installed into /etc/NetworkManager, and is loaded by # NetworkManager by default. To override, specify: '--config file' # during NM startup. This can be done by appending to DAEMON_OPTS in # the file: # # /etc/default/NetworkManager # [main] plugins=ifupdown,keyfile [ifupdown] #managed=false managed=true At this point, it looks like NetworkManager is running but it's not appearing in the NotificationArea of the panel. I don't know what else to try. Any ideas?

  Read the article

< Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >