Search Results

Search found 27870 results on 1115 pages for 'standard output'.

Page 305/1115 | < Previous Page | 301 302 303 304 305 306 307 308 309 310 311 312  | Next Page >

• Exchange 2010: Possible to close for incomming mails for specific acount and reply with "no longer a

  - by Mestika

  Hi, I was wondering if it is possible, in Exchange server 2010, to disable a mailbox account, lets call it mailuser and if anyone sends a E-mail for [email protected] then it will send a mail back with some sort of standard "This E-mail is no longer in use. Please write to [email protected] instead" mail. I know I can create an "out-of-office" reply from the users outlook, but it would be so much faster to do it within the exchange server. Sincerely Mestika

  Read the article

• Ruby: Widely Distributed?

  - by Yar

  While I know it's not part of the Posix standard, but how widely distributed is Ruby on Linux, Unix and other *nix's? I ask because I loathe sh and use Ruby whenever I can on Ubuntu and OSX, but I don't want to get too locked in to 'strange' solutions.

  Read the article

• Logging Redirect Location in Apache

  - by matthew

  Using the standard "Combined" log format, when Apache returns a 301 response it logs it in the access log, which is good, but it only logs the response code. It doesn't log the location to which the client is being directed. What argument do I need to add to the CustomLog format in order to get it to log this information? It wasn't obvious to me from the documentation.

  Read the article

• Allowing a private subnet EC2 access to the internet - Amazon AWS

  - by Xavier Hutchinson

  I have a VPC "VPC with Public and Private Subnets" created via the VPC wizard which should include NAT for the private subnet VPCs however it's not working. They are unable to browse the internet, resolve internet names and ping internet IPs. This is a stock standard conf, I am very sure of that so I am unsure why it's not working. Perhaps there was something additional I am supposed to do that I don't know about? Thank you, Xavier.

  Read the article

• Adding custom service to nagiosgraph

  - by ravloony

  I have successfully added nagiosgraph to our nagios installation. I also added a memory checker plugin, from here : http://blog.vergiss-blackjack.de/2010/04/nagios-plugin-to-check-memory-consumption/. However I can't seem to get the graph of this service to be output by nagiosgraph. The plugin returns a single line like this: 31% (3785 of 11903 MB) used so i added a rule like this to the map file: /output:(\d+)% \((\d+) of (\d+) MB\) used/ and push @s, ['Mem', ['Percentage', 'GUAGE', $1], ['Used', 'GUAGE', $2], ['Total', 'GUAGE', $3] ]; I have also read this : http://www.mail-archive.com/[email protected]/msg36835.html and made sure that process_performance_data=1 in the nagios conf file. So far I have no graph for the Mem service on any host, and no rrd file either. I am unsure how to proceed to get this working. The documentation is rather difficult to follow and I haven't managed yet to understand it enough to do this. Can anyone point me to a tutorial, or some documentation which explains the steps needed to get a service noticed and graphed by nagiosgraph?

  Read the article

• How to display escaped characters in tmux status bar

  - by walrus

  i am running tmux from a tty on an embedded linux device. (NOT a terminal emulator) because the screen is rather small, i want to add some "icons" to the tmux status bar. to achieve this, i have simply created a font with the appropriate glyphs for things like battery, or wifi. i can load the font, and display the characters with calls that use an escape to the line drawing characters like so: echo -e "\xe\234\xf" \xe escapes me into line drawing character mode, \234 is my created character, and \xf returns me to normal character mode so my terminal doesnt start getting goofy. this works perfectly if i enter the command at the terminal whether tmux is started or not. the issue arises if i then try to use it in my ~/.tmux.conf file for the status bar. i currently have a line like this: set -g status-right "#(echo -e "\xe\234\xf") #(/script/to/output/powerlevel) this simply outputs \xe\234\xf powerlevel this goes the same if i try printf over echo. this is the output i would expect to get on the terminal if i made the call without passing -e to echo, or without enclosing the statement with quotes. i then decided to wrap the calls to the echo or printf in a shell script. again, the script works when called from the terminal, but not in tmux's status bar. now i get the unprintable character "?" instead of my icon, like this: ? powerlevel this is what i would expect if i did not use the line drawing escapes previously mentioned above, or if i tried to copy and paste the character as text using tmux. in addition, the calling of these character scripts screws up the rest of my status-right, as the clock has about 6 digits for minutes when it is called (though it correctly only updates two of them). how can i make tmux respect the escape characters? any help or insight is greatly appreciated.

  Read the article

• can't ssh from mac to windows (running ssh server on cygwin)

  - by Denise

  I set up an ssh server on a fresh windows 7 machine using the latest version of cygwin. Disabled the firewall. I can ssh into it from itself, from a different windows box (using winssh), and from a linux vm. In spite of that, I tried to ssh in from two different macs, and neither would let me! This is the debug output: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 3dbuild [172.18.4.219] port 22. debug1: Connection established. debug1: identity file /Users/Denise/.ssh/identity type -1 debug1: identity file /Users/Denise/.ssh/id_rsa type 1 debug1: identity file /Users/Denise/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5 debug1: match: OpenSSH_5.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '3dbuild' is known and matches the RSA host key. debug1: Found key in /Users/Denise/.ssh/known_hosts:43 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /Users/Denise/.ssh/identity debug1: Offering public key: /Users/Denise/.ssh/id_rsa Connection closed by [ip] It shows the same output, and fails at the same place, whether I have put my public key on the ssh server or not. Any help would be appreciated-- hopefully someone has run into this before?

  Read the article

• Windows - How to remotely watch log files

  - by weismat

  I would like to look at some log files solely via the console on a standard Windows 7 machine. The logs are created by schedulded tasks and I find it a hazzle to use VNC for this purpose. What technology should I look at? Powershell, Cygwin via ssh or something else? The log files are written using log4Net - thus there might also be an easy way to reconfigure it to create events or something else for remote display.

  Read the article

• Can two Identical devices be present on the same bus in any PCI Topology

  - by vaibbhav

  As per the PCI standard, devices are identified on the basis of Vendor Id, Device Id and the bus no. All devices of same type have identical vendor id and device id. If I put two such devices on the same bus say bus 0. How will the PCI Software Subsystem distinguish between the two? If such a case is not possible in PCI, then can such thing be possible through PCI Express Switch?

  Read the article

• Email hosting on home's Windows server 2003

  - by klay

  Hi guys, I am new to Server management, I have a static Ip address and I bought recently a domain name, I configure the domain name to target my Ip address. I am running windows server 2003 standard. what are the steps to host my email adresses? Do I need to buy anything else, or what I have is enough (static ip address, domain name, win server 2003, exchange server 2003) ?? thanks Guys

  Read the article

• Free-space driven log rotation on linux?

  - by kdt

  Someone just asked me 'how long should we keep logs for our application', and my answer was 'until the disk is full' as there's no reason to throw them away other than running out of space. However, standard logrotate wants us to specify a specific period + number of rotations. Is there something similar that would let us say "rotate daily, and keep as much history as you like until there is only 5% space free"? The platform is Redhat Linux.

  Read the article

• Finding custom printer-specific options on *nix

  - by enbuyukfener

  Hey all, I have a printer set up using CUPS (FujiXerox Document Center 1100), it is named DC1100. There are capabilities of the printer that are not shows as options of the printer as listed by: lpoptions -l -d DC1100 The output is below: PrintoutMode/Printout Mode: Draft *Normal High Photo InputSlot/Media Source: Upper Lower MultiPurpose LargeCapacity Manual *Standard PageSize/Page Size: *Letter A4 C5 C6 COM10 DL Executive Legal Monarch Statement PageRegion/PageRegion: Letter A4 C5 C6 COM10 DL Executive Legal Monarch Statement STP_Brightness/Brightness: 0.00 0.02 0.04 [snip] 2.00 STP_Contrast/Contrast: 0.00 0.05 0.10 0.15 [snip] 4.00 STP_ColorCorrection/Color Correction: Accurate Bright Density [snip] Uncorrected STP_DitherAlgorithm/Dither Algorithm: Adaptive EvenTone Fast [snip] VeryFast STP_EnableDensity/Density Enable: *Disabled Enabled STP_Density/Density Value: 0.1 0.2 0.3 0.4 [snip] 8.0 STP_EnableGamma/Composite Gamma Enable: *Disabled Enabled STP_Gamma/Composite Gamma Value: 0.10 0.15 0.20 0.25 [snip] 4.00 STP_LinearContrast/Linear Contrast Adjustment: *False True STP_Duplex/Double-Sided Printing: DuplexNoTumble DuplexTumble *None Resolution/Rendering Resolution: *FromPrintoutMode 150x150dpi 300x300dpi 600x600dpi OutputType/Output Type: *FromPrintoutMode BlackAndWhite Grayscale STP_ImageType/Image Type: *FromPrintoutMode Photo Graphics LineArt None Text TextGraphics STP_Resolution/Resolution: *FromPrintoutMode 150dpi 300dpi 600dpi I am particularly looking for options for: "secure print" (possibly by setting a mode and setting a username) stapling hole punching Perhaps I need a vendor specific driver/PPD file? If so, any pointers as I have no idea where to look for one. I haven't been able to find one on the official site or on sites such as http://www.openprinting.org

  Read the article

• Can two Identical devices be present on the same bus in any PCI Topology

  - by vaibbhav

  As per the PCI standard, devices are identified on the basis of Vendor Id, Device Id and the bus no. All devices of same type have identical vendor id and device id. If I put two such devices on the same bus say bus 0. How will the PCI Software Subsystem distinguish between the two? If such a case is not possible in PCI, then can such thing be possible through PCI Express Switch?

  Read the article

• Which config file gets changed in an embedded tomcat instance to enable gzip compression?

  - by spowers

  Our developers have provided a web application bundled with an 'embedded' instance of tomcat. They have not enabled gzip compression of css or js files, and am wondering if there is a standard configuration file to change this in like there is with a standalone tomcat server?

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• FFmpeg convert video w/ dropped frames, out of sync

  - by preahkumpii

  I recorded a video using Bandicam with the MJPEG encoder to get the least amount of lag. Now, I am trying to convert that massive file to a h264 avi using ffmpeg. I know there are dropped frames in the video stream...more than 100 in the first two minutes, which I assume is simply because Bandicam dropped some when it couldn't keep up. So, when I convert the file to h264, the video and audio are out of sync, and appear to be more and more out of sync as output video progresses. Here is my basic command in ffmpeg: ffmpeg -i "C:\...\input.avi" -vcodec libx264 -q 5 -acodec libmp3lame -ar 44100 -ac 2 -b:a 128k "C:\...\output.avi" I have tried EVERYTHING I can think of including: -itsoffset [-]00:00:01 Tried this before and after input file. This doesn't work because as the video progresses it becomes more and more out of sync. -async 1 Doesn't work. -vsync 1 Doesn't work, but it does show dropped frames being duplicated. Two inputs of same file with mapping using -map 0:0 -map 1:1. Doesn't work. The source plays just fine. Any ideas how to convert it with ffmpeg and keep the audio and video synced? Thanks.

  Read the article

• Office 2007 Installer Not Logging When Run During Startup Script

  - by bshacklett

  I'm using a startup script to deploy Microsoft Office 2007 Standard. It's not working quite right and I'm trying to find logging information for it. Unfortunately, no log is being generated by setup. I've tried configuring the log at %temp%\, C:\, %systemroot%\temp and leaving it at defaults, all to no avail. Nothing is showing up in the event logs, either. Is there anywhere else I can go to look for information on what's going on with the installer?

  Read the article

• How long does a typical Windows 7 64bit installation take?

  - by Borek

  On a machine with Intel Core-i5 or i7 and a standard HDD, how long should an installation of Windows 7 64 bit roughly take? I'm after a rough estimate because my installation seems to be running quite slowly (previously, I've installed Win7 32bit on a laptop and it went much quicker but maybe there are differences between 32 and 64 bit editions).

  Read the article

• Blocking an IP from connecting

  - by Sam W.

  I have a problem with my Apache webserver where there's and IP than connecting to my server, using alot of connection and wont die which eventually making my webserver timeout. The connection will stay as SYN_SENT state if I check using netstat -netapu I even flush my iptables and use the basic rules and it still doesn't work. The IP will get connected when I start my Apache Basic rules that I use: iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT iptables -A INPUT -s 89.149.244.117 -j REJECT iptables -A OUTPUT -s 89.149.244.117 -j REJECT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A INPUT -p tcp --dport 21 -j ACCEPT iptables -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT iptables -A INPUT -j REJECT iptables -A FORWARD -j REJECT The bold part is rule in question. Not sure this is related but tcp_syncookies value is 1. Can someone point out my mistake? Is there a way to block it for good. Thank you

  Read the article

• Off-the-shelf solutions for migrating data from azure blobstorage to rackspace cloud files

  - by S.C.

  I have large amounts of data (500+ GB) stored in azure blob storage that I need to transfer to rackspace cloud files. I know it is possible to perform such a migration using the SDKs from both services, but is there a free, standard, 1-step process for doing this? I've built a POC utility but would like to avoid having to optimize it to perform the transfer within a reasonable amount of time. Thanks.

  Read the article

• Small business: what should I know about computer security?

  - by geschema

  I run a small (1 man) consulting company in the field of embedded systems, working from home using a standard DSL internet access. My main development machine is a Windows XP PC, which is connected to the router with an ethernet cable. I also have a MacBook Pro laptop, which is connects to the network via WLAN (WPA-PSK). Besides enabling the Windows firewall, not using IE, having an up-to-date antivirus program and strong passwords, what do I need to know to keep my customers' data safe on these computers?

  Read the article

• iptables -- OK, **now** am I doing it right?

  - by Agvorth

  This is a follow up to a previous question where I asked whether my iptables config is correct. CentOS 5.3 system. Intended result: block everything except ping, ssh, Apache, and SSL. Based on xenoterracide's advice and the other responses to the question (thanks guys), I created this script: # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP Now when I list the rules I get... # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any anywhere anywhere state INVALID 9 612 ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:ssh 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:https 0 0 DROP all -- any any anywhere anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 5 packets, 644 bytes) pkts bytes target prot opt in out source destination I ran it and I can still log in, so that's good. Anyone notice anything major out of wack?

  Read the article

• unable to recover data from failed hdd

  - by Eslam Elyamany

  my hdd failing (or maybe totally dead) i've connected the hdd via USB but it doesn't appear in fdisk Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xe9fb38fb Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 40959999 20376576 7 HPFS/NTFS/exFAT /dev/sda4 40962046 976771071 467904513 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 82913280 86910975 1998848 82 Linux swap / Solaris /dev/sda6 86913024 394113023 153600000 7 HPFS/NTFS/exFAT /dev/sda7 40962048 82913279 20975616 83 Linux /dev/sda8 394122708 976768064 291322678+ 7 HPFS/NTFS/exFAT Partition 8 does not start on physical sector boundary. no sdc appears here , BUT it's appears on /dev/ rootghost-lap:/home/ghost# ls /dev/sd* /dev/sda /dev/sda2 /dev/sda5 /dev/sda8 /dev/sdb /dev/sdc1 /dev/sdc2 /dev/sdc6 /dev/sdc8 /dev/sda1 /dev/sda4 /dev/sda6 /dev/sda9 /dev/sdc /dev/sdc10 /dev/sdc5 /dev/sdc7 /dev/sdc9 also it appears in proc Code: rootghost-lap:/home/ghost# cat /proc/partitions major minor #blocks name 8 0 488386584 sda 8 1 102400 sda1 8 2 20376576 sda2 8 4 1 sda4 8 5 1998848 sda5 8 6 153600000 sda6 8 8 291322678 sda8 8 9 20975616 sda9 11 0 1048575 sr0 11 1 99136 sr1 8 32 244198583 sdc 8 33 14651248 sdc1 8 34 1 sdc2 8 37 15380480 sdc5 8 38 4153344 sdc6 8 39 48829536 sdc7 8 40 48829536 sdc8 8 41 110374551 sdc9 8 42 1975963 sdc10 and dmesg : [10604.777168] end_request: I/O error, dev sdc, sector 1 [10604.817238] sd 26:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [10604.817243] sd 26:0:0:0: [sdc] Sense Key : Aborted Command [current] [10604.817248] sd 26:0:0:0: [sdc] Add. Sense: No additional sense information [10604.817253] sd 26:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 02 00 00 06 00 ok now , let's see what i've tried testdisk to check for partitions -- failed dd to copy data from /dev/sdcX -- provide strange output size for example /dev/sdc1 is about 15G , the output for dd is 62G+ so i had to cancle it safecopy successfully made an image for partitons , but can't fix images, can't mount it, can't do any thing with it and some other tools i've tried and all failed , so any idea ?

  Read the article

• Best grep-like tool

  - by e-satis

  I do in file search a lot, and used to love grep. Then I learn the existence of egrep, so I switched to benefit from the advanced regexp. Then I discovered the Eclipse search tool. Much easier to use that grep. Then I found ack : fast, easy, powerful. And now I use grin, which is smooth for pythonistas. I know there is also a couple of this kind of tools with a GUI. So what tool do you use, and why do you think it's the best. Practical features generally are : fast to fire and use; speedy processing; automatically ignore useless files; colored output; output lines, filename, context; allow complex regexp; allow a custom filtering and ouput; GUI + command line intergation; let you open an editor from the result set. There are some related posts on SO : http://stackoverflow.com/questions/87350/what-are-good-grep-tool-for-windows http://stackoverflow.com/questions/981601/colorized-grep-viewing-the-entire-file-with-highlighting http://stackoverflow.com/questions/1028107/is-there-some-unix-util-that-will-allow-me-to-grep-multiple-files-with-little-type http://stackoverflow.com/questions/1027906/unix-find-grep-syntax-vs-awk

  Read the article

• Can I use iptables on my Varnish server to forward HTTPS traffic to a specific server?

  - by Dylan Beattie

  We use Varnish as our front-end web cache and load balancer, so we have a Linux server in our development environment, running Varnish with some basic caching and load-balancing rules across a pair of Windows 2008 IIS web servers. We have a wildcard DNS rule that points *.development at this Varnish box, so we can browse http://www.mysite.com.development, http://www.othersite.com.development, etc. The problem is that since Varnish can't handle HTTPS traffic, we can't access https://www.mysite.com.development/ For dev/testing, we don't need any acceleration or load-balancing - all I need is to tell this box to act as a dumb proxy and forward any incoming requests on port 443 to a specific IIS server. I suspect iptables may offer a solution but it's been a long while since I wrote an iptables rule. Some initial hacking has got me as far as iptables -F iptables -A INPUT -p tcp -m tcp --sport 443 -j ACCEPT iptables -A OUTPUT -p tcp -m tcp --dport 443 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 443 -j DNAT --to 10.0.0.241:443 iptables -t nat -A POSTROUTING -p tcp -d 10.0.0.241 --dport 443 -j MASQUERADE iptables -A INPUT -j LOG --log-level 4 --log-prefix 'PreRouting ' iptables -A OUTPUT -j LOG --log-level 4 --log-prefix 'PostRouting ' iptables-save > /etc/iptables.rules (where 10.0.0.241 is the IIS box hosting the HTTPS website), but this doesn't appear to be working. To clarify - I realize there's security implications about HTTPS proxying/caching - all I'm looking for is completely transparent IP traffic forwarding. I don't need to decrypt, cache or inspect any of the packets; I just want anything on port 443 to flow through the Linux box to the IIS box behind it as though the Linux box wasn't even there. Any help gratefully received... EDIT: Included full iptables config script.

  Read the article

< Previous Page | 301 302 303 304 305 306 307 308 309 310 311 312  | Next Page >