Search Results

Search found 23653 results on 947 pages for 'disk problems'.

Page 307/947 | < Previous Page | 303 304 305 306 307 308 309 310 311 312 313 314  | Next Page >

• ESXi 5.1 ghettoVCB stuck at Clone: 10% done

  - by stormdrain

  Trying to run ghettoVCB for the first time here. I am using a NAS that is set up as a datastore on the host. I did a dry run and it completed without error. The VM is ~500GB and there is only one on the host that I'm trying to backup. I proceeded to start the actual backup: ./ghettoVCB.sh -m vmname -g ghettoVCB.conf It goes though the config and looks like it's taking off: 2013-10-24 11:43:19 -- info: CONFIG - USING GLOBAL GHETTOVCB CONFIGURATION FILE = ghettoVCB.conf 2013-10-24 11:43:19 -- info: CONFIG - VERSION = 2013_01_11_0 2013-10-24 11:43:19 -- info: CONFIG - GHETTOVCB_PID = 17398616 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_VOLUME = /vmfs/volumes/nas2tb-001/esxi4 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_ROTATION_COUNT = 3 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_DIR_NAMING_CONVENTION = 2013-10-24_11-43-18 2013-10-24 11:43:19 -- info: CONFIG - DISK_BACKUP_FORMAT = thin 2013-10-24 11:43:19 -- info: CONFIG - POWER_VM_DOWN_BEFORE_BACKUP = 0 2013-10-24 11:43:19 -- info: CONFIG - ENABLE_HARD_POWER_OFF = 0 2013-10-24 11:43:19 -- info: CONFIG - ITER_TO_WAIT_SHUTDOWN = 4 2013-10-24 11:43:19 -- info: CONFIG - POWER_DOWN_TIMEOUT = 5 2013-10-24 11:43:19 -- info: CONFIG - SNAPSHOT_TIMEOUT = 15 2013-10-24 11:43:19 -- info: CONFIG - LOG_LEVEL = info 2013-10-24 11:43:19 -- info: CONFIG - BACKUP_LOG_OUTPUT = /tmp/ghettoVCB-2013-10-24_11-43-18-17398616.log 2013-10-24 11:43:19 -- info: CONFIG - ENABLE_COMPRESSION = 0 2013-10-24 11:43:19 -- info: CONFIG - VM_SNAPSHOT_MEMORY = 0 2013-10-24 11:43:19 -- info: CONFIG - VM_SNAPSHOT_QUIESCE = 0 2013-10-24 11:43:19 -- info: CONFIG - ALLOW_VMS_WITH_SNAPSHOTS_TO_BE_BACKEDUP = 0 2013-10-24 11:43:19 -- info: CONFIG - VMDK_FILES_TO_BACKUP = all 2013-10-24 11:43:19 -- info: CONFIG - VM_SHUTDOWN_ORDER = 2013-10-24 11:43:19 -- info: CONFIG - VM_STARTUP_ORDER = 2013-10-24 11:43:19 -- info: CONFIG - EMAIL_LOG = 0 2013-10-24 11:43:19 -- info: 2013-10-24 11:43:22 -- info: Initiate backup for vmname 2013-10-24 11:43:22 -- info: Creating Snapshot "ghettoVCB-snapshot-2013-10-24" for serv2 Destination disk format: VMFS thin-provisioned Cloning disk '/vmfs/volumes/esxi4-storage/vmname/vmname_1.vmdk'... Clone: 10% done. and it's been that way for over an hour now. Stuck at Clone: 10% done.. Thing is: I can see the vmdk on the NAS. And it looks like almost the whole thing is there. On the NAS it's showing ~430GB but on vSphere Client Summary is shows as 507GB. I don't see the vmdk on the NAS growing any more. The logfile mimics some of the above and is sitting at "Creating Snapshot..." and nothing else is coming in. Is the vmdk on the NAS showing all those GB because of the provisioning or something? i.e. is the size of the file not necessarily indicative of the amount of actual data that has been copied? Is there are reason it might be "Stuck" at 10%? i.e. could it really be taking this long? Any other tips? Thanks. Edit: as soon as I hit the Submit button, I glance over to see that it has incremented to 11% done. Good to know it'll be complete sometime around when the sun explodes.

  Read the article

• data recovery from deleted partition

  - by anique

  i recently merged my hard disk partitions f into c using a partition manager, i didnt need data in f but unfortunately i forgot to backup some important office docs in that partition. manager formated f and merged the space into c. is it possible for me to recover from a deleted partition, how will i do that thanks

  Read the article

• Time machine failing to backup as sparsebundle is already in use

  - by Michael Neale

  I have an airport extreme with a drive connected, and use it for backing up snow leopard macs. I have an occasional problem with one of them that says "the backup disk image ... is already in use" and it fails to backup. Any ideas?

  Read the article

• Disk2VHD image used in Win 7 as a bootable VPC

  - by John

  I have used Disk2VHD to create a VHD of my old XP Laptop's boot drive. I would like to use it as an XP virtual machine on my new Win7 machine. I have tried doingit on a second XP machine and the VPC boots properly using that VHD but under Win7 I can't get it to act as the boot disk for the VPC. Any ideas? TIA J

  Read the article

• Our application is responding different on client server

  - by WtFudgE

  I have an application running on our local server and it works perfect. However when I deploy my application to our client's server there are problems. If i copy all the sources to another local from their server, it works fine again.... I am talking about an ASP.NET application talking with windows server 2008. The server specs of our client are: intel Xeon 2.13 GHz 6 GB RAM 300 GB HDD windows server 2008 R2 Although I think it's not that important I will describe the problems I am talking about to give u a better idea: It is related to upating and deleting fields in the sql server. Whenever there is more than one user running the application, and updates or deletes (not even the same record!0, there seems to be fields updating/deleting wrongly. But as I said before, if we copy the source to another server it is not the case. So I assumed it is more configuration related. Do you guys have any idea what the issue could be? Thanks a lot EDIT: my client old me he disabled the sql related accounts Could this be related?

  Read the article

• Clone virtual machine with Server 2008 R2 and Hyper-V?

  - by bwerks

  Hi all, I've recently just started working with Hyper-V, and so far it's quite nice. However, I've been running into problems with what seems like it should be the most basic of workflows. I've set up a baseline Server 2008 R2 configuration, and exported it with the intention of using the export for cloning. I entered "C:\Exports\" as the export folder. However, I run into problems when I try to import the image. From the Hyper-V manager, I select "Import Virtual Machine" and in the resulting window I entered "C:\Exports\BuildServer\" as the folder, set the radial to "Copy the virtual machine (create a new unique ID)" and checked the checkbox for "Duplicate all files so the same virtual machine can be imported again." Doing so results in the following error: "Import failed. Import task failed to copy file from 'H:\Exports\BuildServer\Virtual Hard Disks\BuildServer.vhd' to 'C:\Hyper-V\Virtual Hard Disks\BuildServer.vhd': The file exists. (0x80070050)" Have I somehow messed something up in configuration? Or is this a known thing? I've read it should be possible to clone VMs by copying them in the filesystem but I'd prefer to keep things in the management Ui if possible.

  Read the article

• How to aggregate data in Windows Performance Monitor?

  - by Jader Dias

  I have seem performance counters like this: PhysicalDisk(_Total)\Avg. Disk Read Queue Length Which is an aggregation (average, sum, etc) of data over a period. How to create a custom counter which is an aggregation of existent data of another counter?

  Read the article

• Can't connect to LAN when connected to D-Link DIR-615

  - by Senseful

  I'm have a D-Link DIR-615 Wireless N 300 Router. I didn't use the CD it comes with to set up the network. Instead I configured it manually through the router's settings that are accessed via a web browser. The main changes I made are: Secured the router so that a password is required before clients can use the wireless internet. Broadcasting 802.11N only (not B or G). I can connect to the router just fine and I'm able to access the internet. The only problem is that I don't see any of the other computers in my LAN. When I try connecting to another Wi-Fi router that I have (which is connected to the same network), I can see all of the computer's on my LAN just fine. Therefore, I'm guessing that the reason I can't connect to the LAN is not a problem with my computer and is a problem with the router instead. I'm on a MacBook Air running Mac OS X 10.6.6. I tried contacting D-Link technical support, but they only try to help you if you have problems connecting to the internet. They aren't really concerned with problems that have to do with the accessing PC's on the same network.

  Read the article

• Windows 7 + Deep Freeze - I'm stuck in an endless reboot loop

  - by myermian

  I have the following setup: Windows 7 Ultimate Deep Freeze I "thawed" my machine last night and performed a Windows Update. The update is having issues (it gets stuck at 32%, fails, and restarts my machine). When it reboots it attempts it again, and again, and again, etc. (Endless loop). I looked online and found some solutions, but none of them seem to be working: When I run Safe Mode, Safe Mode w/ Network, or Safe Mode w/ Command Prompt it attempts to revert the Windows Update changes. However, the problem is with Deep Freeze on (and now in "Frozen" mode) the reverted changes don't stay, and I'm back into the loop of death. Oh, and side note: "Safe Mode w/ Command Prompt" does not actually take me to a command prompt window? Perhaps because it is attempting to complete the Windows Update changes first? I have tried to select the option to NOT restart when an windows error occurs, but it still does. I tried the remainder of all the other options in the F8 screen. The only other option left is to find my Windows 7 Media Disc (I can't find it right now) and use it to repair windows (because for some reason the repair option does not show up in the F8 screen). Is there a way to disable Deep Freeze from loading? When I selected "Safe Mode w/ Command Prompt" I noticed that it loads the DpFrz.sys file. I know that when I'm in the Windows Boot Manager if I press F10 instead of F8 (while highlighting Windows 7) it takes me to an "Edit Boot Options" screen: Edit Windows boot options for: Windows 7 Path: \Windows\system32\winload.exe Partition: 2 Hard Disk: 8e90e329 [ /NOEXECUTE=OPTIN (I CAN EDIT THIS LINE) ] Update: I found my Windows 7 Media Disk and it did not help out. The laptop had the "System Restore" as a partition on the HDD. I later received (in the mail) a Windows 7 Upgrade Disc from Sony to upgrade my system from Windows Vista to Windows 7 Ultimate. I placed the disc into the DVD drive and it does not come up as a "bootable" disc. I'm going to try to find an alternative disc to see if I can get into Command Prompt. Update 2: I got a Windows Repair disc and got into a command prompt window. I got into the registry and disabled Deep Freeze. Also: I renamed the Pending.xml file to Pending.old I cleared out the Windows Temp directory I still am stuck in the loop (though, it isn't an issue with DeepFreeze anymore because I can make changes to the hard drive and they persist). Not sure what to do at this point? Update 3: I ran the repair option and it couldn't repair, but it did point me to something. It says the error was due to a driver that was failing. I have a feeling it is my UPEK Fingerprint scanner.

  Read the article

• Ububtu server 12.04 auto installation freezes at kickseeding running if ks.cfg has post scripts

  - by john206

  I'm trying to make a custom Ubuntu Server iso file. Kickstart file (ks.cfg) runs smooth when there is no %post in the file and Ubuntu installs correctly with ks configuration. Installation finishes installing base, apt, grub and It echos: Kickseed Running... and it freezes @ 0% I thought may be apt-get update doesnt work in ks file, I tried to install other apps like apache2 but no luck I have created dozen iso images and installed them in Virtual Box.I have been googling for 3 days and checked out ubuntu forums but haven't figured out the issue. I appreciate your help. This is how I made the iso image. My ks.file and txt.cfg files located in isolinux directory: root@ubuntu:/home/work mount -o loop ubuntu-12.04-amd64.iso original-iso/ rsync -a original-iso/ custom-iso/ cp ks.cfg custom-iso/isolinux/ cp txt.cfg custom-iso/isolinux/ chmod -R 777 custom-iso/ #Creating Iso image mkisofs -D -r -V “$IMAGE_NAME” -cache-inodes -J -l -b isolinux/isolinux.bin -c isolinux/boot.cat -no-emul-boot -boot-load-size 4 -boot-info-table -o ~/ubuntu-12.04-alternate-custom-amd64.iso custom-iso/ ks.cfg #Generated by Kickstart Configurator #platform=AMD64 or Intel EM64T #System language lang en_US #Language modules to install langsupport en_US #System keyboard keyboard us #System mouse mouse #System timezone timezone America/Los_Angeles #Root password rootpw --iscrypted somethingsomething #Initial user user ubuntu --fullname "ubuntu" --iscrypted --password somethingsomething. #Reboot after installation reboot #Use text mode install text #Install OS instead of upgrade install #Use CDROM installation media cdrom #System bootloader configuration bootloader --location=mbr #Clear the Master Boot Record zerombr yes #Partition clearing information clearpart --all --initlabel #Disk partitioning information part /boot --size 128 --fstype=ext3 --asprimary part / --size 512 --fstype=ext3 --asprimary part swap --size 512 part /tmp --size 512 --fstype=ext3 part /var --size 512 --fstype=ext3 part /usr --size 4096 --fstype=ext3 part /home --size 2048 --fstype=ext3 #System authorization infomation auth --useshadow --enablemd5 #Network information network --bootproto=dhcp --device=eth0 #Firewall configuration firewall --disabled --http --ftp --ssh #X Window System configuration information xconfig --depth=32 --resolution=1024x768 --defaultdesktop=GNOME %post apt-get update mkdir /home/user txt.cfg default autoinstall label autoinstall menu label ^Install Custom Ubuntu Server kernel /install/vmlinuz append file=/cdrom/preseed/ubuntu-server.seed initrd=/install/initrd.gz quiet ks=cdrom:/isolinux/ks.cfg -- label install menu label ^Install Ubuntu Server kernel /install/vmlinuz append file=/cdrom/preseed/ubuntu-server.seed vga=788 initrd=/install/initrd.gz quiet -- label cloud menu label ^Multiple server install with MAAS kernel /install/vmlinuz append modules=maas-enlist-udeb vga=788 initrd=/install/initrd.gz quiet -- label check menu label ^Check disc for defects kernel /install/vmlinuz append MENU=/bin/cdrom-checker-menu vga=788 initrd=/install/initrd.gz quiet -- label memtest menu label Test ^memory kernel /install/mt86plus label hd menu label ^Boot from first hard disk localboot 0x80

  Read the article

• symantec endpoint vs. symantec protection agent

  - by Chadworthington

  I made the upgrade and while my download speeds seem to improve SIGNIFICANTLY, I get an marked increased in periodic disk thrashing, more so than with Protection Agent. What is your experience?

  Read the article

• touch /forcefsck not working on Fedora16

  - by Harry

  I need to run fsck in order to repair my one and only hard-disk. I have no rescue CD/USB available. I did the following: touch /forcefsck chmod a+rw /forcefsck # just to be really sure reboot But no fsck happened on reboot, though the /forcefsck file quietly disappeared (why BTW?)! I saw some responses on the Net suggesting a shutdown -rF to auto-run fsck on reboot, but the shutdown I have on my F16 does not have any -F option.

  Read the article

• Why did MAC-Adress Cloning Fix My Router?

  - by FranticPedantic

  I have a Belkin router, and about a year ago, I suddenly lost my internet connectivity from Comcast. The internet worked fine when I plugged it right into my laptop, so I just ignored it. When I moved to another apartmnet I eventually took the dive and called tech support. The tech told me to clone my MAC address which completely fixed the issue. Now I know what a MAC address is and I've read what MAC cloning is. What has bothered me since is that I don't see how this fixed the issue. As I have understood MAC address cloning, it has the router pretend it has the same MAC address as my computer. Here is why I don't understand why this fixes my issue: I have used several different computers with this router. Cloning the MAC address fixed it for ALL of my computers. The laptop I first used with my ISP was not the one that I eventually had connected when I cloned the address. Furthermore, I didn't have any problems for quite some time after I stopped using the first computer. It wasn't like the internet suddenly stopped working when I changed which laptop I was using Now it occurred to me that maybe there was some sort of expiration? Except... Which MAC address did it clone? It was just an option in the router administration page. Did it just pick whichever computer was connected to it? If my ISP still wanted the MAC of my first computer, how did some other computer's fix it? As mentioned earlier, why did this problem seemingly stem from nowhere? Anyway, I don't have any current problems so this is more just out of general curiosity. If anybody can explain it, it would be appreciated!

  Read the article

• GRUB 2 freezing at OS selection screen, what could be the cause?

  - by Michael Kjörling

  Mains power is somewhat unreliable where I live, so every now and then, the computer gets rebooted when the PSU can't maintain proper voltage during a brown-out or momentary black-out. It's happened a few times recently that when power is restored, the BIOS POST completes successfully, GRUB starts to load and then freezes. I've seen this at the Welcome to GRUB! message, but it seems to happen more often just past the switch to the graphical OS list. At this point, the computer will not respond to anything (arrow keys, control commands, Ctrl+Alt+Del, ...) - it simply sits there displaying this image, seemingly doing nothing more. At that point, turning the computer off using the power button and letting it sit for a while (cooling down?) has allowed it to boot successfully. Turning the computer off and immediately back on seems to give the same result (successful POST then freeze in GRUB). This behavior began recently, although does not seem to be directly correlated with my hard disk woes (although it may be relevant that GRUB resides on that physical disk, I don't know). Once the computer has booted, it runs without a hitch. I know that a "proper" solution would be to invest in a UPS, but what might be causing behavior like this? I was thinking in terms of perhaps the CPU shutting down as a thermal control measure, but if that was the cause then wouldn't I see similar freezes during use (which I do not)? What else could cause freezes apparently closely but not perfectly related to the BIOS handover from POST to OS bootloader? The BIOS settings are to reset to previous power status after a power loss. Since the PC in question is almost always turned on, this means restore to full power status. I have no expansion cards installed that make any BIOS extensions known by screen output during the boot process, at least, but I do have a few expansion cards installed. Haven't made any changes in that regard in a long time, now. I haven't touched GRUB itself for a long time, whether configuration or binaries, so I don't think that's the problem. Also, it doesn't really make sense that a bug in GRUB would manifest itself only once in a blue moon but significantly more often after a power failure.

  Read the article

• OSX 10.6.6 SSH md5 break-in check

  - by Alex

  Information Recently one of the linux servers that I access was compromised to steal passwords and ssh keys using a modified ssh binary. This lead me to question if the attacker had compromised my OSX Laptop which had ssh access turned on. A sophos virus scan turned up nothing, and I did not have rkhunter installed before the attack, so I could not compare hashes of the system binaries to be sure. However because OSX is relatively standard for each of their major releases, I asked fiends for md5 hashes md5 /usr/bin/ssh and md5 /usr/sbin/sshd as a basic first check to see if there was anything different about my machine. A few emails later I have found the following data: Version (Arch) [N] MD5 (/usr/bin/ssh) MD5 (/usr/sbin/sshd) OSX 10.5.8 (PPC) [3] 1e9fd483eef23464ec61c815f7984d61 9d32a36294565368728c18de466e69f1 OSX 10.5.8 (intel) [5] 1e9fd483eef23464ec61c815f7984d61 9d32a36294565368728c18de466e69f1 OSX 10.6.x (intel) [7] 591fbe723011c17b6ce41c537353b059 e781fad4fc86cf652f6df22106e0bf0e OSX 10.6.x (intel) [4] 58be068ad5e575c303ec348a1c71d48b 33dafd419194b04a558c8404b484f650 Mine 10.6.6 (intel) df344cc00a294c91230c65e8b7332a79 b5094ccf4cd074aaf573d4f5df75906a where N is the number of machines with with that MD5, and the last row is my laptop. The sample is relatively heterogeneous spaning a few years of different makes and models of Apples, and different versions of 10.6.x. The different hash for my system made me worried that these binaries might have been compromised. So I made sure that my backup for the week was good, and dived into formatting my system and reinstalling OSX. After reinstalling OSX from the manufacturer DVD, I found that the MD5 hash did not change for either ssh, or sshd. Goal Make sure that my system is does not have any malicious software. Should I be worried that this base install of OSX (with no other software installed) has been compromised? I have also updated my system to 10.6.6 and found no change as well. Other Information I am not sure if this is helpful information, but my laptop is a i7 15 inch MacBook Pro bought in Nov 2010, and here is some output from system_profiler: System Software Overview: System Version: Mac OS X 10.6.6 (10J567) Kernel Version: Darwin 10.6.0 64-bit Kernel and Extensions: No Time since boot: 1:37 Hardware: Hardware Overview: Model Name: MacBook Model Identifier: MacBook6,2 Processor Name: Intel Core i7 Processor Speed: 2.66 GHz Number Of Processors: 1 Total Number Of Cores: 2 L2 Cache (per core): 256 KB L3 Cache: 4 MB Memory: 4 GB Processor Interconnect Speed: 4.8 GT/s Boot ROM Version: MBP61.0057.B0C SMC Version (system): 1.58f16 Sudden Motion Sensor: State: Enabled On the laptop, I find: $ codesign -vvv /usr/bin/ssh /usr/bin/ssh: valid on disk /usr/bin/ssh: satisfies its Designated Requirement $ codesign -vvv /usr/sbin/sshd /usr/sbin/sshd: valid on disk /usr/sbin/sshd: satisfies its Designated Requirement $ ls -la /usr/bin/ssh -rwxr-xr-x 1 root wheel 1001520 Feb 11 2010 /usr/bin/ssh $ ls -la /usr/sbin/sshd -rwxr-xr-x 1 root wheel 1304800 Feb 11 2010 /usr/sbin/sshd $ ls -la /sbin/md5 -r-xr-xr-x 1 root wheel 65232 May 18 2009 /sbin/md5 Update So far I have not gotten an answer about this question, but if you could help by increasing the number of hashes that I can compare against, that would be great. To get hashes, and version numbers, run the following on osx: md5 /usr/bin/ssh md5 /usr/sbin/sshd ssh -V sw_vers

  Read the article

• System lockout, SAM error 12294

  - by Suneel

  We are facing a login issue due to a SAM error with the error code 12294. Event Type: Error Event Source: SAM Event Category: None Event ID: 12294 Date: Time: User: Computer: Description: The SAM database was unable to lockout the account of due to a resource error, such as a hard disk write failure (the specific error code is in the error data) . Accounts are locked after a certain number of bad passwords are provided so please consider resetting the password of the account mentioned above.

  Read the article

• How to back up non-standard directories in my user profile with Windows Backup?

  - by James Johnston

  I'm using Windows Backup to back up my Win7 Pro laptop. I'd like to use it to back up my complete user profile, but I only see standard profile directories (e.g. C:\Users\JohnstonJ\Documents) in the list. Non-standard ones aren't there (e.g. C:\Users\JohnstonJ\MyCustomDirectory). What's the best way to handle this? The only thing I can think of is to browse under the "Computer" entry and navigate directly to C:\Users\JohnstonJ and check off the entire profile (to get what's in there, and any new directories that come up). But is that going to back up the profile twice? Cause other unforeseen problems given that I checked it off by navigating through the computer, rather than picking it under the "Data Files" category? (e.g. back up temporary file garbage, files in use problems, etc. that the "Data Files" category might be handling better). Looking for solutions that other people use that are known to work well and still uses the Windows Backup software - I don't really want to fuss with 3rd-party backup software. Example - as you can see, I have two directories in my profile that Windows Backup is not offering to back up: "Dropbox" and "New folder": (Link to images album because I don't have enough reputation to directly embed them: http://imgur.com/a/Xyv5u)

  Read the article

• problem when view the super block in ext3 file system

  - by xuczhang

  I tried to view the superblock by command "dd" in ext3 file system. dd if=/dev/sda3 bs=4096 skip=1 count=1 of=superblock But the result in superblock file is not correct(I compare the value of Inodes count I got from dumpe2fs). The device file /dev/sda3 is started at the boot block and then the superblock of the group0? And another question is the boot block and superblock's size are both BLOCKSIZE(here is 4096)? The disk format of ext2/ext3(I think they are the same) are shown below:

  Read the article

• Repair OS From Within VMWare

  - by Zurahn

  I've got a Debian installation in an installation of ESXi that won't boot due to the deletion of a few system files that need to be restored. It would be preferable to at least access the files on the instance, if a repair is impossible. To complicate matters, there isn't enough room on the drive to upload a full distribution to boot from with VMWare disk utility. Any ideas on how to accomplish this?

  Read the article

• Xenserver 5.5 doesn't see RAID volume

  - by Roy Chan

  Hi Gurus, I am trying to install Xenserver on a Dell precision 490 workstation. After booting into the install wizard and next-ed a few times, On the disk step, it only shows physical harddrive but not the RAID (RAID-10) volume that I set up on the Dell RAID. Is there a special option that I have to set on the boot? or do I need a special driver for this? Please Advise Thanks

  Read the article

• My acer aspire 5532 laptop mouse

  - by Karen Wells

  The mouse pad on my laptop has stopped working. It has not been turned off as we already checked. The computer tech stated it was a windows 7 problem. The laptop is only 3 months old. They suggested that I try to run a recovery. However, I put the disk in and nothing happens. How can this problem be fixed?

  Read the article

• External USB attached drive works in Windows XP but not in Windows 7. How to fix?

  - by irrational John

  Earlier this week I purchased this "N52300 EZQuest Pro" external hard drive enclosure from here. I can connect the enclosure using USB 2.0 and access the files in both NTFS partitions on the MBR partitioned drive when I use either Windows XP (SP3) or Mac OS X 10.6. So it works as expected in XP & Snow Leopard. However, the enclosure does not work in Windows 7 (Home Premium) either 64-bit or 32-bit or in Ubuntu 10.04 (kernel 2.6.32-23-generic). I'm thinking this must be a Windows 7 driver problem because the enclosure works in XP & Snow Leopard. I do know that no special drivers are required to use this enclosure. It is supported using the USB mass storage drivers included with XP and OS X. It should also work fine using the mass storage support in Windows 7, no? FWIW, I have also tried using 32-bit Windows 7 on both my desktop, a Gigabyte GA-965P-DS3 with a Pentium Dual-Core E6500 @ 2.93GHz, and on my early 2008 MacBook. I see the same failure in both cases that I see with 64-bit Windows 7. So it doesn't appear to be specific to one hardware platform. I'm hoping someone out there can help me either get the enclosure to work in Windows 7 or convince me that the enclosure hardware is bad and should be RMAed. At the moment though an RMA seems pointless since this appears to be a (Windows 7) device driver problem. I have tried to track down any updates to the mass storage drivers included with Windows 7 but have so far come up empty. Heck, I can't even figure out how to place a bug report with Microsoft since apparently the grace period for Windows 7 email support is only a few months. I came across a link to some USB troubleshooting steps in another question. I haven't had a chance to look over the suggestions on that site or try them yet. Maybe tomorrow if I have time ... ;-) I'll finish up with some more details about the problem. When I connect the enclosure using USB to Windows 7 at first it appears everything worked. Windows detects the drive and installs a driver for it. Looking in Device Manager there is an entry under the Hard Drives section with the title, Hitachi HDT721010SLA360 USB Device. When you open Windows Disk Management the first time after the enclosure has been attached the drive appears as "Not initialize" and I'm prompted to initialize it. This is bogus. After all, the drive worked fine in XP so I know it has already been initialized, partitioned, and formatted. So of course I never try to initialize it "again". (It's a 1 GB drive and I don't want to lose the data on it). Except for this first time, the drive never shows up in Disk Management again unless I uninstall the Hitachi HDT721010SLA360 USB Device entry under Hard Drives, unplug, and then replug the enclosure. If I do that then the process in the previous paragraph repeats. In Ubuntu the enclosure never shows up at all at the file system level. Below are an excerpt from kern.log and an excerpt from the result of lsusb -v after attaching the enclosure. It appears that Ubuntu at first recongnizes the enclosure and is attempting to attach it, but encounters errors which prevent it from doing so. Unfortunately, I don't know whether any of this info is useful or not. excerpt from kern.log [ 2684.240015] usb 1-2: new high speed USB device using ehci_hcd and address 22 [ 2684.393618] usb 1-2: configuration #1 chosen from 1 choice [ 2684.395399] scsi17 : SCSI emulation for USB Mass Storage devices [ 2684.395570] usb-storage: device found at 22 [ 2684.395572] usb-storage: waiting for device to settle before scanning [ 2689.390412] usb-storage: device scan complete [ 2689.390894] scsi 17:0:0:0: Direct-Access Hitachi HDT721010SLA360 ST6O PQ: 0 ANSI: 4 [ 2689.392237] sd 17:0:0:0: Attached scsi generic sg7 type 0 [ 2689.395269] sd 17:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 2689.395632] sd 17:0:0:0: [sde] Write Protect is off [ 2689.395636] sd 17:0:0:0: [sde] Mode Sense: 11 00 00 00 [ 2689.395639] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412003] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412009] sde: sde1 sde2 [ 2689.455759] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.455765] sd 17:0:0:0: [sde] Attached SCSI disk [ 2692.620017] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2707.740014] usb 1-2: device descriptor read/64, error -110 [ 2722.970103] usb 1-2: device descriptor read/64, error -110 [ 2723.200027] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2738.320019] usb 1-2: device descriptor read/64, error -110 [ 2753.550024] usb 1-2: device descriptor read/64, error -110 [ 2753.780020] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2758.810147] usb 1-2: device descriptor read/8, error -110 [ 2763.940142] usb 1-2: device descriptor read/8, error -110 [ 2764.170014] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2769.200141] usb 1-2: device descriptor read/8, error -110 [ 2774.330137] usb 1-2: device descriptor read/8, error -110 [ 2774.440069] usb 1-2: USB disconnect, address 22 [ 2774.440503] sd 17:0:0:0: Device offlined - not ready after error recovery [ 2774.590023] usb 1-2: new high speed USB device using ehci_hcd and address 23 [ 2789.710020] usb 1-2: device descriptor read/64, error -110 [ 2804.940020] usb 1-2: device descriptor read/64, error -110 [ 2805.170026] usb 1-2: new high speed USB device using ehci_hcd and address 24 [ 2820.290019] usb 1-2: device descriptor read/64, error -110 [ 2835.520027] usb 1-2: device descriptor read/64, error -110 [ 2835.750018] usb 1-2: new high speed USB device using ehci_hcd and address 25 [ 2840.780085] usb 1-2: device descriptor read/8, error -110 [ 2845.910079] usb 1-2: device descriptor read/8, error -110 [ 2846.140023] usb 1-2: new high speed USB device using ehci_hcd and address 26 [ 2851.170112] usb 1-2: device descriptor read/8, error -110 [ 2856.300077] usb 1-2: device descriptor read/8, error -110 [ 2856.410027] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 2856.730033] usb 3-2: new full speed USB device using uhci_hcd and address 11 [ 2871.850017] usb 3-2: device descriptor read/64, error -110 [ 2887.080014] usb 3-2: device descriptor read/64, error -110 [ 2887.310011] usb 3-2: new full speed USB device using uhci_hcd and address 12 [ 2902.430021] usb 3-2: device descriptor read/64, error -110 [ 2917.660013] usb 3-2: device descriptor read/64, error -110 [ 2917.890016] usb 3-2: new full speed USB device using uhci_hcd and address 13 [ 2922.911623] usb 3-2: device descriptor read/8, error -110 [ 2928.051753] usb 3-2: device descriptor read/8, error -110 [ 2928.280013] usb 3-2: new full speed USB device using uhci_hcd and address 14 [ 2933.301876] usb 3-2: device descriptor read/8, error -110 [ 2938.431993] usb 3-2: device descriptor read/8, error -110 [ 2938.540073] hub 3-0:1.0: unable to enumerate USB device on port 2 excerpt from lsusb -v Bus 001 Device 017: ID 0dc4:0000 Macpower Peripherals, Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0dc4 Macpower Peripherals, Ltd idProduct 0x0000 bcdDevice 0.01 iManufacturer 1 EZ QUEST iProduct 2 USB Mass Storage iSerial 3 220417 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 5 Config0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 4 Interface0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Update: Results using Firewire to connect. Today I recieved a 1394b 9 pin to 1394a 6 pin cable which allowed me to connect the "EZQuest Pro" via Firewire. Everything works. When I use Firewire I can connect whether I'm using Windows 7 or Ubuntu 10.04. I even tried booting my Gigabyte desktop as an OS X 10.6.3 Hackintosh and it worked there as well. (Though if I recall correctly, it also worked when using USB 2.0 and booting OS X on the desktop. Certainly it works with USB 2.0 and my MacBook.) I believe the firmware on the device is at the latest level available, v1.07. I base this on the excerpt below from the OS X System Profiler which shows Firmware Revision: 0x107. Bottom line: It's nice that the enclosure is actually usable when I connect with Firewire. But I am still searching for an answer as to why it does not work correctly when using USB 2.0 in Windows 7 (and Ubuntu ... but really Windows 7 is my biggest concern). OXFORD IDE Device 1: Manufacturer: EZ QUEST Model: 0x0 GUID: 0x1D202E0220417 Maximum Speed: Up to 800 Mb/sec Connection Speed: Up to 400 Mb/sec Sub-units: OXFORD IDE Device 1 Unit: Unit Software Version: 0x10483 Unit Spec ID: 0x609E Firmware Revision: 0x107 Product Revision Level: ST6O Sub-units: OXFORD IDE Device 1 SBP-LUN: Capacity: 1 TB (1,000,204,886,016 bytes) Removable Media: Yes BSD Name: disk3 Partition Map Type: MBR (Master Boot Record) S.M.A.R.T. status: Not Supported

  Read the article

• Linux Kernel Packet Forwarding Performance

  - by Bob Somers

  I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

  Read the article

• VMWare vmfs vs NFS datastore with vmdk?

  - by CarpeNoctem

  I want to add a new harddisk to an existing VM and want the best performance possible. The new hard disk will exist on an NFS datastore. Currently I did the following: Created new vmdk on NFS datastore Created new lvm partition using fdisk Create new physical volume, volume group, and logical volume (2TB) Created ext3 partition on logical volume Is there a better way to do this? Should I be doing some vmware-ish file system instead?

  Read the article

• SSH hangs without password prompt

  - by Wilco

  Just reinstalled OS X and for some reason I now cannot connect to a specific machine on my local network via SSH. I can SSH to other machines on the network without any problems, and other machines can SSH to the problematic one as well. I'm not sure where to start looking for problems - can anyone point me in the right direction? Here's a dump of a connection attempt: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 10.0.1.7 [10.0.1.7] port 22. debug1: Connection established. debug1: identity file /Users/nwilliams/.ssh/identity type -1 debug1: identity file /Users/nwilliams/.ssh/id_rsa type -1 debug1: identity file /Users/nwilliams/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.5 debug1: match: OpenSSH_4.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '10.0.1.7' is known and matches the RSA host key. debug1: Found key in /Users/nwilliams/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password,keyboard-interactive debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic ... at this point it hangs for quite a while, and then resumes ... debug1: Unspecified GSS failure. Minor code may provide more information Server not found in Kerberos database debug1: Unspecified GSS failure. Minor code may provide more information Server not found in Kerberos database debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Trying private key: /Users/nwilliams/.ssh/identity debug1: Trying private key: /Users/nwilliams/.ssh/id_rsa debug1: Trying private key: /Users/nwilliams/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive

  Read the article

< Previous Page | 303 304 305 306 307 308 309 310 311 312 313 314  | Next Page >