Search Results

Search found 1691 results on 68 pages for 'brand'.

Page 31/68 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

• HP DL380 G5 Predictive Drive Failure on a new drive

  - by CharlieJ

  Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results. I also tried all the suggestions from this question Why doesn't Windows 7 wake up from sleep?. Still no results.

  Read the article

• Start FF with plugins disabled.

  - by justSteve

  Strange problem. Opened FF 3.6.3 after a re-boot and my last opened tabs appeared but none of the page or menu elements would respond to a click. No error messages...just locked up. Started FF with a different profile and it works normally. Next i used FEBE to restore a backup of my working profile and, after the restore, it's doing the same thing - locked out. No newly installed plugins but since a brand new profile works while a restored one doesn't it kinda points to a problematic plug-in. Is there any way to start FF with all plugins disabled? thx

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state [closed]

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results.

  Read the article

• Jungledisk - choosing between Amazon S3 and Rackspace ?

  - by Dietmar

  Hi, jungledisk is owned by rackspace and offers an option to choose Amazon S3 which charges for traffic whereby if data is stored on rackspace, no charges for traffic. For a small company, to just backup files with jungle disk from ubuntu linux OS computers, i wonder what to choose. Commercial psychologically the price on traffic and the Amazon brand make it appear or maybe it is, of better quality than the cheaper Rackspace offer which is when it comes for just backing up ok ? but if its about backing up around 30 GB which updates from time to time, what would you consider a good choice ?

  Read the article

• Unable to sync the Zune software with my HTC HD7

  - by Varpi

  I have a brand new HTC HD7 with Windows Phone 7, with no Software installed. I am running on Windows 7 64 bit. Whenever I try to sync my Mobile Device with Zune- I get this message: Can't connect to your phone. Disconnect it, restart it, then try connecting again I've downloaded latest Zune software and all updates. I don't have any certificates on my personal certificates. My phone is listed under Portable devices in Device manager (It shows as phone with driver version 4.7.965.0). I've restarted both my computer and the mobile device few times. I tried unlocking the device during the Zune sync Any ideas as to how I can sync my phone ?

  Read the article

• Ubuntu 9.10 LiveCD stalls after "Install Ubuntu" selected from boot menu on eMachines

  - by nicorellius

  I am trying to install Ubuntu 9.10 from the ISO on a CD (it needs to be this version) on an eMachine with a brand new Seagate hard disk. The CD boots OK, and I choose the language. Then I am presented with the boot menu: Try Ubuntu Install Ubuntu etc I have tried the top two choices several times (trying Ubuntu and installing it), but each and every time the installation stalls and the disc stops spinning right after I hit enter after choosing the option I want. I have tried different CD/DVD drives, changing the jumpers on both CD drives, different hard drives, and nothing works. Maybe there is a BIOS setting that is choking the installation? Any help would be appreciated. Edit - I just tried running the hard drive as the master on the primary IDE and the CD drive as the slave on the primary with the same results. Maybe flash the BIOS?

  Read the article

• Cross-Forest Trust

  - by cdalley

  I am looking at testing a cross-domain trust we can have two domain controllers (with different forests and domain names) setup so we can move everyone onto the new domain. We do NOT run exchange on site and we do not have any links to O365 to AD currently. Onto the problem: I have setup two DCs in a Virtual Machine: They are on the same network 192.168.0.* The Windows 2003 server: Name: OLDSRVR "Clone" of our current Domain Controller IP: 192.168.0.1 Domain: internal.test.com The Windows 2012 server: Name: ADCTEST01 Brand new domain setup from scratch separate to internal.test.com Domain: internal.test2.com IP: 192.168.0.2 OLDSRVR can only see ADCTEST if it has dynamic IP set. If I set a static IP it cannot see it. If I try using the dynamic IP and try to join it gets to the end then complains "??The trust relationship between this workstation and the primary domain failed" Any ideas?

  Read the article

• Backup and restore.

  - by Xavierjazz

  I have a Thinkpad T60 with a 150GIg internal hard drive. XP Pro SP3. I also have a similar hard drive that used to be in another laptop connected via USB. It contains only data. I have cleared out a lot of duplicate files and now would like to back both up. I have Retrospect and a brand new 1Tbyte drive for this purpose. Can I back up the whole computer (both drives) but, in case only one fails, can I just restore that drive or do I have to restore both drives at the same time? I don't understand how partitions work so might I be able to partition the 1T drive and restore each smaller drive independently? Thanks.

  Read the article

• Will disabling NAT on my wireless router cause a performance hit on my DSL router?

  - by user117313

  I have a Thomson TG508v2 router/modem and a brand new AirPort Extreme connected to it. At first, I set the AirPort Extreme to "share a public IP", which enables DHCP/NAT. Everything works great but I was having the Double NAT error. So I set the AirPort Extreme as bridge mode, which disables DHCP/NAT and let my crappy modem handle my internal network IPs. Will this cause any performance hit in my network? I'm worried because I'll outsource this job from AirPort Extreme (premium hardware) to the crappy modem. Before you suggest, I tried setting my modem as a bridge and configuring PPPoE on the AirPort Extreme, however it wouldn't connect to the internet, so I just dismissed leaving the modem as bridge.

  Read the article

• external HDD with SATA & USB interface?

  - by Greg

  Anyone know of an external HDD that would have (in addition to USB) a SATA (eSATA) port/cable? i.e. Brand/Model. Preferably one of the name brands so I have a better change of finding it here or locally if possible. Background - In one location I want to use it is I would like to increase the performance by cabling it directly to the PC SATA port, HOWEVER I don't want to have to open up the PC to do this each time. I was thinking of running a SATA cable out through the PC case so I just plug it directly into the external HDD in question. Perhaps it should be also externally powered too so I don't need to run a power cable out from the PC power supply.

  Read the article

• Re-Calibrate Toshiba battery meter with Windows 7

  - by Farseeker

  Hi All. I have a Toshiba U300 laptop. Back in the olden days (circa-2000) you could re-calibrate the battery meter from the BIOS when your battery was no longer reading accurately. My battery was shot, so I bought a brand new one, however Windows 7 still seems to count down the battery life in at the same speed as the old one did. This time, when it alleged 0%, I turned the laptop back on and got another 90 minutes of life out of it, at 0%. Is there a tool or utility for Toshiba laptops that can fix it back to being accurate? I've read the other threads on SU about cycling the battery but that just doesn't seem to do it in this case. Update: After the last cycle, the battery meter now reads 100% but the indicator on the front of the laptop is still orange (indicating not fully charged)

  Read the article

• Machine only responds to network requests from machines it is pinging

  - by ILikeFood

  I have two machines. WOPR: Ubuntu server edition 10.10 LTS 32 bit Adam Selene: Windows 7 home premium 64 bit / Ubuntu Desktop 10.10 LTS 64 bit I want to be able to SSH from Adam Selene to WOPR, so I connect them to the same network. Here's where things get weird. I cannot connect to WOPR in any way under normal circumstances. But, if WOPR is pinging Adam, then it starts responding to ping requests, HTTP gets, and SSH tunnels. I'm an amateur, and brand new to Ubuntu server, so I suspect there's a misconfiguration somewhere, but there's an off chance it's a bug in the OS. Does anyone know what might cause this behavior? Thanks a lot!

  Read the article

• Win8 ASUS R503 - My PS/2 touchpad will not allow me to update to the required 8.0.5.0 version

  - by William Cha

  Details: Brand: ASUS Manufacturer: Toro Model: R503U Attemps: Fn+F9 does not work Cannot update from the 6.--(whatever version) to 8.0.5.0. Pros: 8.0.5.0 Allows Fn+F9 to function, which allows quick touchpad disabling. Cons: Cannot update; "Your driver is up to date." I want to play and type on this notebook laptop without excessive palm strokes on the touchpad. I have that name there, showing that this is a touchpad (PS/2) I do not want nor want to use. Does anybody have a good solution to this problem?

  Read the article

• HP Z210 SFF: two different video cards produce no Displayport output when installed

  - by ConcernedOfTunbridgeWells

  I have a HP Z210 SFF that I'm trying to install a video card into. I've tried two different cards in Slot 2 (a Quadro FX380LP and a Quadro 600). Neither of these cards produce a displayport signal when installed. With neither installed the displayport port on the motherboard works fine with the built in graphics. When I install the cards it produces no signal and the cards don't either. The Quadro 600 is brand new and the odds of having two dead video cards is quite low. Is there something fundamental that I could be missing out - a BIOS setting maybe?

  Read the article

• Converting PDF eBooks into a Kindle format

  - by Ender

  Over the past couple of years I've amassed quite a collection of guides, tutorials and ebooks in PDF format. A lot of these are quite useful for work, especially PDF documentation, and rather than have to be at a computer every time I want to read how to do something in Sitecore or to read through a software testing ebook I'd like to do it on my brand-spanking-new Kindle. However, even though there is now a native PDF reader on the Kindle due to the nature of PDF's they are practically unreadable. The text doesn't wrap due to how PDF's are sized and so far after a bunch of Google searches I've yet to find a viable solution to get my PDF's converted into a readable Kindle format. Sometimes these books have code or pictures/tables in them, but most of the time they're text-heavy and to be honest I'd be surprised if there wasn't a free tool to handle the converting of PDF to one of the (seemingly many) Kindle formats. So, can anyone help me out with this?

  Read the article

• Page File - Why set one for each drive?

  - by Magic

  Hello, I have Windows Vista Business Edition running on my laptop (brand is HCL). I have 4 HDD which are as follows - C - 29.2 GB (of which only 3.68 GB is free) D - 39 GB (of which 37.8 GB is free) E - 39 GB (of which 37.3 GB is free) F - 41.6 (of which 41.4 GB is free) However, my page file settings are as below. Automatically manage paging file for all drives. Question - Why should I set one for each drive? Should I set my page file on the OS Root Drive. I happen to talk to a System Administrator in an IT company and he advised that we should never set the page file on the OS drive but on an alternate drive wherever possible. It would be really helpful, if you can guide me here or at least point me to the right resources so that I can read about paging and best practices of paging. Cheers,

  Read the article

• Reliability of S.M.A.R.T.?

  - by Mark

  I've been using ActiveSmart to monitor my hard-drives health for a few weeks now, and its telling me my brand new 1.5 TB hard-drive is half-dead already. About on-par with one of my hard-drives which I know is at least half dead because I've been having some read errors and heard ticking noises. Now I haven't actually noticed any problems with my 1.5 TB drive; should I be concerned that it's going to crap out on me too? Or could ActiveSmart be giving a mis-diagnosis because I use it a lot or something (I've used up 795 GB in the 2 and a half weeks I've had it). The events that ActiveSmart has been catching is "Hardware ECC recovered". Maybe these new fangled super big hard-drives somehow rely on ECCs to squeeze out the extra space, but this isn't actually a cause for concern?

  Read the article

• Intel RAID0 on Windows 8 not Displaying Correct Media Type

  - by kobaltz

  I have my primary C Drive which consists of 2 Intel 120GB SSD Drives in a RAID0. I have a clean install of Windows 8 Pro, latest MEI software, latest RST software, latest Intel Toolbox. Prior to this I had installed Windows 8 Pro as an upgrade. When I went into the Optimize Drives while in the Upgrade installation, it showed the Media Types as Solid State Drives. However, now since I am in a brand new install, it is showing the Media Type as Hard Disk Drive. I am worried about this because of the trim not working properly. Before when in the upgrade, it showed SSD as the media type and the Optimize option would perform a manual trim. Unfortunately, my search credentials on Google are so common to many other things (ie Raid0, SSD, Windows 8, Media Type) that all I am finding are useless topics. Before, (found on random site) it showed the Media Type as below

  Read the article

• HD read error while booting linux

  - by sidharth sharma

  I have been dual booting windows 7 and ubuntu on my laptop since the past 3 years and all was working fine until I started getting logs like ata1.00: status: { DRDY ERR } ata1.00: error: { UNC } ata1.00: configured for UDMA/133 sd 0:0:0:0: [sda] Unhandled sense code sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 0:0:0:0: [sda] Sense key: Medium Error [Current][discreptor] I figured it was a hardware problem and ignored it as long as I could until the HD crashed on me. Then I got a brand new HD and put on windows and ubuntu afresh on it but the problem still persists. Any Help?

  Read the article

• Second display freaks out when waking from sleep

  - by inkedmn

  I have two laptops, an older white MacBook and a brand new Macbook Pro. When either computer is on my desk, I connect it to a second, widescreen display (Acer, a couple years old, uses DVI). The Macbook connects via mini DVI and the MBP connects via mini displayport. When the Macbook is connected and everything goes to sleep, I'm able to wake the machine and both displays in the normal way and everything is fine. Sometimes, when waking the MBP, the laptop and primary display are fine, but the second display shows a bunch of static. If I restart the display, everything's fine. This probably happens 70% of the time when the MBP goes to sleep while connected to this display. Any idea what could be causing this?

  Read the article

• Laptop touchpad works incorrect when on power supply

  - by Ikke

  My original laptop adapter broke down, so I've baught a new one. It's a no-brand adapter from a dutch internet shop. The power of the new adapter is slightly more than the old adapter, but in my opinion that shouldn't be a problem. The laptop is a Toshiba Sattelite L40-15B. When the old adapter broke down due to short circuit, this laptop was connected. When the adapter is unplugged, the touchpad works correctly and smoothly. But as soon as it is connected, the cursor moves jumpy, and response badly. Does anyone know where this problem comes from, and if there's a solution?

  Read the article

• Best way to deploy my node.js app on a Varnish/Nginx server

  - by Saif Bechan

  I am about to deploy a brand new node.js application, and I need some help setting this up. The way my setup is right now is as follows. I have Varnish running on external_ip:80 I have Nginx behind running on internal_ip:80 Both are listening on port 80, one internal port, one external. NOTE: the node.js app runs on WebSockets Now I have the my new node.js application that will listen on port 8080. Can I have varnish set up that it is in front of both nginx and node.js. Varnish has to proxy the websocket to port 8080, but then the static files such as css, js, etc has to go trough port 80 to nignx. Nginx does not support websockets out of the box, else I would so a setup like: varnish - nignx - node.js

  Read the article

• Problems with Black Box KVM

  - by MrWizard54

  I just recieved a shipment of equipment orderd by my predicessor that includes brand new Dell Optiplex 990 computers, with standard mice and keyboards. Also included were Black Box ServSwitch Secure KVMs. I've worked with KVMs before and hypothetically they should be the easiest thing in the world to deal with, plug it all together, push the button, go. However, for the life of me I can't get the computers to recognize the mouse or keyboard when plugged into the KVM. We've seen this with multiple KVMs across the order. Any one know what I'm missing? Computers are all Dell 990 with Windows 7.

  Read the article

• Is there any Mac Pro hardware parts that can ONLY be purchased thru Apple?

  - by bigp

  I'd like to know if I need to be concerned about any hardware parts that I should include in a brand new Mac Pro purchase, instead of trying to hunt it down on 3rd party vendors (or whitelist vendors / hardware suppliers). The main components I'm interested for "upgradeability" are: Processors (If starting with Two 2.4GHz Quad-Core "Westmere"); RAM (If starting with the least possible, which seems to be 6 x 1GB); Video Cards (If starting with one ATI Radeon HD 5770, can a 2nd one be purchased elsewhere?) Hard-Drives (Since these are mounted in specialized trays [if I'm not mistaking], are they also sold elsewhere? And can they be bought as SSDs?) Power Supply (Do I need to be concerned about this at all, or does it auto-adjust depending on the new component upgrades?) I just want to be sure by choosing a Mac Pro with lower component specifications that I can in fact purchase upgrade parts cheaper elsewhere. Thanks!

  Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >