Search Results

Search found 1157 results on 47 pages for 'latency'.

Page 31/47 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• How do you manage a complexity jump?

  - by glenatron

  It seems an infrequent but common experience that sometimes you're working on a project and suddenly something turns up unexpectedly, throws a massive spanner in the works and ramps up the complexity a whole lot. For example, I was working on an application that talked to SOAP services on various other machines. I whipped up a prototype that worked fine, then went on to develop a regular front end and generally get everything up and running in a nice, fairly simple and easy to follow fashion. It worked great until we started testing across a wider network and suddenly pages started timing out as the latency of the connections and the time required to perform calculations on remote machines resulted in timed out requests to the soap services. It turned out that we needed to change the architecture to spin requests out onto their own threads and cache the returned data so it could be updated progressively in the background rather than performing calculations on a request by request basis. The details of that scenario are not too important - indeed it's not a great example as it was quite forseeable and people who have written a lot of apps of this type for this type of environment might have anticipated it - except that it illustrates a way that one can start with a simple premise and model and suddenly have an escalation of complexity well into the development of the project. What strategies do you have for dealing with these types of functional changes whose need arises - often as a result of environmental factors rather than specification change - later on in the development process or as a result of testing? How do you balance between avoiding the premature optimisation/ YAGNI/ overengineering risks of designing a solution that mitigates against possible but not necessarily probable issues as opposed to developing a simpler and easier solution that is likely to be as effective but doesn't incorporate preparedness for every possible eventuality?

  Read the article

• Can't connect to hidden network with BCM4313

  - by poomerang

  The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

  Read the article

• Loadbalancing Questions

  - by Van Holtz

  I have been learning networking for about 4 months. Wrote a single standalone Multiplayer server and succeeded with authoritative approach. Now I want to extend it by splitting the single server into clusters to allow even more players to log in to avoid latency issues. Now I have protyped the Loadbalancing server and its running pretty good so far. This is my architecture, I have a master server which acts as a proxy, every sub servers(chat, login, game) connect to the master server as well as all the clients. when a client connects, Client Request: Send Request - MS(Master) - Decides which SS(SubServer) to forward to - Forwards Request to SS - SS - Analyze Message - Send Response to MS - Decides which Client to forward to - Forwards Response to Client Well, it looks like its going through lots of stages. it takes double the time to process the message than a single server approach. i feel like my model isnt the best or i may be wrong. is there any better model or the one they use in professional games? I still want a Master-SubServer approach. I just want to clarify that I'm going in the right direction before writing all my codes. Thanks for any answer :)

  Read the article

• Best peer-to-peer game architecture

  - by Dejw

  Consider a setup where game clients: have quite small computing resources (mobile devices, smartphones) are all connected to a common router (LAN, hotspot etc) The users want to play a multiplayer game, without an external server. One solution is to host an authoritative server on one phone, which in this case would be also a client. Considering point 1 this solution is not acceptable, since the phone's computing resources are not sufficient. So, I want to design a peer-to-peer architecture that will distribute the game's simulation load among the clients. Because of point 2 the system needn't be complex with regards to optimization; the latency will be very low. Each client can be an authoritative source of data about himself and his immediate environment (for example bullets.) What would be the best approach to designing such an architecture? Are there any known examples of such a LAN-level peer-to-peer protocol? Notes: Some of the problems are addressed here, but the concepts listed there are too high-level for me. Security I know that not having one authoritative server is a security issue, but it is not relevant in this case as I'm willing to trust the clients. Edit: I forgot to mention: it will be a rather fast-paced game (a shooter). Also, I have already read about networking architectures at Gaffer on Games.

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• Need help installing the Intel VGA Driver [closed]

  - by Ary Catur Wicaksono

  Possible Duplicate: How do I install the Intel Graphics driver in my system? how to install intel VGA drive..?? I've been searching on google but did not see too I've been trying to ask the ubuntu forum in Indonesia. but they did not reply my post.. is there anything that can help me? *I am sorry my English is rather chaotic arthur@Chunx:~$ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10) arthur@Chunx:~$ sudo lshw -c display [sudo] password for arthur: *-display description: VGA compatible controller product: 82G33/G31 Express Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 10 width: 32 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:42 memory:fea80000-feafffff ioport:dc00(size=8) memory:e0000000-efffffff memory:fe900000-fe9fffff arthur@Chunx:~$ sudo apt-get install xserver-xorg-video-intel Sedang membaca daftar paket... Selesai Membangun pohon ketergantungan Membaca informasi yang tersedia... Selesai xserver-xorg-video-intel telah berada dalam versi terbaru. 0 dimutakhirkan, 0 baru terinstal, 0 akan dihapus dan 190 tidak akan dimutakhirkan.

  Read the article

• Financial institutions build predictive models using Oracle R Enterprise to speed model deployment

  - by Mark Hornick

  See the Oracle press release, Financial Institutions Leverage Metadata Driven Modeling Capability Built on the Oracle R Enterprise Platform to Accelerate Model Deployment and Streamline Governance for a description where a "unified environment for analytics data management and model lifecycle management brings the power and flexibility of the open source R statistical platform, delivered via the in-database Oracle R Enterprise engine to support open standards compliance." Through its integration with Oracle R Enterprise, Oracle Financial Services Analytical Applications provides "productivity, management, and governance benefits to financial institutions, including the ability to: Centrally manage and control models in a single, enterprise model repository, allowing for consistent management and application of security and IT governance policies across enterprise assets Reuse models and rapidly integrate with applications by exposing models as services Accelerate development with seeded models and common modeling and statistical techniques available out-of-the-box Cut risk and speed model deployment by testing and tuning models with production data while working within a safe sandbox Support compliance with regulatory requirements by carrying out comprehensive stress testing, which captures the effects of adverse risk events that are not estimated by standard statistical and business models. This approach supplements the modeling process and supports compliance with the Pillar I and the Internal Capital Adequacy Assessment Process stress testing requirements of the Basel II Accord Improve performance by deploying and running models co-resident with data. Oracle R Enterprise engines run in database, virtually eliminating the need to move data to and from client machines, thereby reducing latency and improving security"

  Read the article

• Why is a software development life-cycle so inefficient?

  - by user87166

  Currently the software development lifecycle followed in the IT company I work at is: The "Business" works with a solution manager to build a Business Requirement document The solution manager works with the Program manager to build a Functional Spec The PM works with the engineering lead to develop a release plan and with the engineering team to develop technical specifications If there are any clarifications required, developers contact the PM who contacts the solution manager who contacts the business and all the way back introducing a latency of nearly 24 hours and massive email chains for any clarifications By the time the tech spec is made, nearly 1 month has passed in back and forth Now, 2 weeks go to development while the test writes test cases Code is dropped formally to test, test starts raising bugs. Even if there is 1 root cause for 10 different issues, and its an easily fixed one, developers are not allowed to give fresh code to test for the next 1 week. After 2-3 such drops to test the code is given to the ops team as a "golden drop" ( 2 months passed from the beginning) Ops team will now deploy the code in a staging environment. If it runs stable for a week, it will be promoted to UAT and after 2 weeks of that it will be promoted to prod. If there are any bugs found here, well, applying for a visa requires less paperwork This entire process is followed even if a single SSRS report is to be released. How do other companies process such requirements? I'm wondering why, the business cannot just drop the requirements to developers, developers build and deploy to UAT themselves, expose it to the business who raise functional bugs and after fixing those promote to prod. (even for more complex stuff)

  Read the article

• Restart and/or graphics problem in Ubuntu 12.04

  - by kara

  I having been using 12.04 for a couple of months now, with v. little problems. The other day I restarted my computer, and though I think it rebooted, the screen would be black. I could not even get a visual from a live cd. Finally, I was able to get it to load, but the resolution has been completely off. The computer thinks I have a laptop screen, when I actually have a ViewSonic VP2330wb, and it detects only two resolutions. And still, I have a problem with rebooting. If the screen locks after I leave it for a while, I can't get a visual back, and then when I force a shutdown, it takes 3 times for me to get a grub screen. Then I have to boot in recovery mode, and then finally in normal mode, but the screen is still always off. This is my video card: description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list configuration: latency=0 resources: memory:fe000000-fe3fffff memory:d0000000-dfffffff ioport:f000(size=64) I am a new ubuntu user, and am at my wits end. Any help would be greatly appreciated.

  Read the article

• Sound not working after installing PCI video card and then removing it

  - by bakhshu

  I am running 11.10 on a HP/Compaq Presario sr1010z, and the video/audio was working fine with whatever was in the machine already. Then I installed a new video card (PCI/nVidia), which disabled the audio/video on the old one automatically. But that card didn't work out too well so I removed it. Now the video is back to normal, but the audio is gone. I have tried the following: 1. In BIOS, set audio to on/enable rather than Auto 2. Looked for hardware in System Settings Sound, but nothing shows up there 3. But when I run the sysinfo utility, I get the description of the audio controller When I do a 'sudo aplay -l', I get 'aplay: device_list:240: no soundcards found...' And then when I do a 'lspci -v | grep -A7 -i "audio"' I get the following: 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS7012 AC'97 Sound Controller (rev a0) Subsystem: Hewlett-Packard Company Device 2a05 Flags: bus master, medium devsel, latency 32, IRQ 5 I/O ports at a000 [size=256] I/O ports at a400 [size=128] Capabilities: 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Any ideas on how to fix this? Thanks

  Read the article

• Can I delete Generic kernel if I use Generic

  - by user206049

  I currently can't update my release as there is not enough space on boot. I just have the one kernel version there, but seem to have both the Generic and Low Latency versions. uname -r just shows 3.8.0-32-lowlatency ls -lah /boot shows -rw-r--r-- 1 root root 899K Oct 2 00:00 abi-3.8.0-32-generic -rw-r--r-- 1 root root 899K Oct 7 09:27 abi-3.8.0-32-lowlatency -rw-r--r-- 1 root root 152K Oct 2 00:00 config-3.8.0-32-generic -rw-r--r-- 1 root root 152K Oct 7 09:27 config-3.8.0-32-lowlatency drwxr-xr-x 3 root root 2.0K Jan 1 1970 efi drwxr-xr-x 5 root root 1.0K Oct 22 10:05 grub -rw-r--r-- 1 root root 32M Oct 22 09:51 initrd.img-3.8.0-32-generic -rw-r--r-- 1 root root 32M Oct 22 10:05 initrd.img-3.8.0-32-lowlatency drwxr-xr-x 2 root root 12K Feb 25 2013 lost+found -rw-r--r-- 1 root root 173K Dec 5 2012 memtest86+.bin -rw-r--r-- 1 root root 175K Dec 5 2012 memtest86+_multiboot.bin -rw------- 1 root root 3.0M Oct 2 00:00 System.map-3.8.0-32-generic -rw------- 1 root root 3.0M Oct 7 09:27 System.map-3.8.0-32-lowlatency -rw------- 1 root root 5.2M Oct 2 00:00 vmlinuz-3.8.0-32-generic -rw------- 1 root root 5.2M Oct 7 09:27 vmlinuz-3.8.0-32-lowlatency So what can I do to allow me to update? Apparently I need 174m on boot and am 40m short.

  Read the article

• Ubuntu 12.04.1 LTS and Nvidia dirver (304.51) 64bit: problem 640x480

  - by nibianaswen

  I have a problem with this configuration: Asus K55V, Ubuntu 12.04 LTS and Nvidia driver 304.51. I have remove the nouveau driver with: apt-get --purge remove xserver-xorg-video-nouveau I installed the official nvidia driver (from www.nvidia.com) but when I reboot the PC the resolution of screen is only 640x480 and the monitor is resized. Mo solution at this problem if i change the xorg.conf. Now i have uninstall the nvidia driver and reinstall with sudo apt-get purge nvidia-current sudo apt-add-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current When I reboot the screen resolution and size is OK, but if I start nvidia-setting I received the message: You do not appear to be using the NVIDIA X driver. and with command: sudo lshw -c display | grep driver I received configuration: driver=i915 latency=0 This sound like the system is using the Intel card. When I launch command lspci | grep VGA the output is: 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1058 (rev ff) And there is no /etc/X11/xorg.conf. I have read a lot of guides on internet but without success.. How i can use nvidia card with the driver that i have installed?

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• How to represent a graph with multiple edges allowed between nodes and edges that can selectively disappear

  - by Pops

  I'm trying to figure out what sort of data structure to use for modeling some hypothetical, idealized network usage. In my scenario, a number of users who are hostile to each other are all trying to form networks of computers where all potential connections are known. The computers that one user needs to connect may not be the same as the ones another user needs to connect, though; user 1 might need to connect computers A, B and D while user 2 might need to connect computers B, C and E. Image generated with the help of NCTM Graph Creator I think the core of this is going to be an undirected cyclic graph, with nodes representing computers and edges representing Ethernet cables. However, due to the nature of the scenario, there are a few uncommon features that rule out adjacency lists and adjacency matrices (at least, without non-trivial modifications): edges can become restricted-use; that is, if one user acquires a given network connection, no other user may use that connection in the example, the green user cannot possibly connect to computer A, but the red user has connected B to E despite not having a direct link between them in some cases, a given pair of nodes will be connected by more than one edge in the example, there are two independent cables running from D to E, so the green and blue users were both able to connect those machines directly; however, red can no longer make such a connection if two computers are connected by more than one cable, each user may own no more than one of those cables I'll need to do several operations on this graph, such as: determining whether any particular pair of computers is connected for a given user identifying the optimal path for a given user to connect target computers identifying the highest-latency computer connection for a given user (i.e. longest path without branching) My first thought was to simply create a collection of all of the edges, but that's terrible for searching. The best thing I can think to do now is to modify an adjacency list so that each item in the list contains not only the edge length but also its cost and current owner. Is this a sensible approach? Assuming space is not a concern, would it be reasonable to create multiple copies of the graph (one for each user) rather than a single graph?

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• Google Chrome on Ubuntu 12.04 not rendering webpages correctly

  - by sumit_gt

  I am facing some serious web page rendering issues with Chrome. It is more prominent during javascript based animations and stuff on websites like youtube. I have tried removing chrome using (sudo apt-get purge google-chrome-stable) and then reinstalling it. But the problems still persist. The same webpages work correctly on firefox on ubuntu and chrome on windows. The problem only shows up when I use chrome on ubuntu. I think the issue has started after I updated to the latest version of Chrome. I have used Chrome previously on this machine without any problems. I have attached a image that demonstrates the issue. What could possibly be the problem? PS: here's the output of lshw -c video: *-display description: VGA compatible controller product: Madison [Radeon HD 5000M Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:46 memory:e0000000-efffffff memory:f0020000-f003ffff ioport:d000(size=256) memory:f0000000-f001ffff Here's the output of lspci -nn: output of lspci -nn

  Read the article

• Wireless connection disconnects and reconnects with a Netgear WNA1000

  - by William Berkenkamp

  Ever since I made the permanent switch from Vista to Ubuntu i've had wireless connectivity problems. From watching the network manager when it disconnects it seems like it turns off the receiver for some reason. Could it be bad drivers? I used their install software and the site doesn't really offer driver downloads. The adapter is a Netgear WNA1000 if memory serves, and I don't know much about the router except that it's a Motorola Surfboard. And I figure this might help a bit *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: 00:1b:b9:a7:39:a4 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:d800(size=256) memory:feaff000-feafffff memory:feac0000-feadffff *-network description: Wireless interface physical id: 1 bus info: usb@2:1.1 logical name: wlan0 serial: 00:26:f2:8b:fb:38 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.2.0-24-generic-pae firmware=1.9.4 ip=10.0.0.36 link=yes multicast=yes wireless=IEEE 802.11bgn I have tried installing WICD and it didn't fix the problem. Any help would be greatly appreciated. This problem is greatly limiting what I can do with my computer.

  Read the article

• No sound after upgrading to Ubuntu 11.10 from win7

  - by Tilman

  just as a prefix to my question, i'd like to note that i'm just now entering the world of Linux (unless you count my android, but that's a very different experience...) i have two computers now that run Ubuntu 11.10, the first of which i've had very little problems with, aside from figuring out the basics. the second, from which i'm writing this question, has (up to this point) only had one problem.... no sound. i've read a couple questions similiar and found little help as the component catalog doesn't have my computer listed. (in fact i'm not suprised this is a pos i had my mom grab from her work before they officially closed the doors behind them) had perfect sound before hand, and no sound now. sudo lspci -v brings up 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) Subsystem: Intel Corporation Device d608 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at ff980000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel any help would be greatly appreciated, me and my gf just wanna watch a damn movie lol

  Read the article

• Ubuntu 12.04 still slow at mounting internal filesystem

  - by Matthew Goson

  I'm using Toshiba laptop with this configuration: - CPU: Core i5, 2.4GHz - RAM: 4GB - Graphics card: Intel - Hard disk: 500GB SATA I installed Ubuntu 12.04 64bit and got the same issue with this guy Very slow boot due to mounting filesytem, I tried all suggestions there but the slow boot issue still here. Here's a part of my dmesg: [ 2.041015] usbhid: USB HID core driver [ 2.101378] usb 1-1.6: new full-speed USB device number 5 using ehci_hcd [ 2.137980] atl1c 0000:04:00.0: version 1.0.1.0-NAPI [ 2.779080] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 22.822597] udevd[381]: starting version 175 [ 22.837954] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.850837] lp: driver loaded but no devices found [ 23.003822] Adding 7079096k swap on /dev/sda7. Priority:-1 extents:1 across:7079096k [ 23.407915] mei: module is from the staging directory, the quality is unknown, you have been warned. [ 23.408153] mei 0000:00:16.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 23.408160] mei 0000:00:16.0: setting latency timer to 64 [ 23.408211] mei 0000:00:16.0: irq 44 for MSI/MSI-X [ 23.433196] [drm] Initialized drm 1.1.0 20060810 Additional information: my sda1 is a primary NTFS partition, sda2 is a primary ext4 partition which I installed Ubuntu onto. Other partitions are inside an extended partition.

  Read the article

• Ubuntu 14.04 install fails with Via S3 UniChrome Pro graphics

  - by WizardNo.7

  I am trying to install Ubuntu 14.04 on a Fujitsu Siemens Amilo Pro laptop(it's quite old yes, has about 30GB Hard Drive and I think 192mb of RAM) which currently has Windows XP installed (which I'd like to keep for the time being). I have downloaded the 32-bit Desktop ISO and used unetbootin to create a Live USB for this laptop. When I boot from USB, I arrive at the unetbootin Grey and Blue menu and pick either "Try Ubuntu without installing", or "Install Ubuntu". The menu goes away and an Ubuntu loadscreen showing UBUNTU and four dots which progressively change between white and orange. At about the second color changing cycle a white underscore symbol appears next to the fourth dot and flickers. There is some leftover text from the kernel boot still visible, but there is no graphical desktop. After this I have to hard reboot or shut-down. $ lshw -c video *-display UNCLAIMED description: VGA compatible controller product: CN700/P4M800 Pro/P4M800 CE/VN800 Graphics [S3 UniChrome Pro] Vendor: VIA Technologies, Inc. physical id: 0 bus info: pci@0000:01:00.0 version: 01 width: 32 bits clock: 66MHz capabilities: pm agp agp-2.0 vga_controller bus_master cap_list configuration: latency=64 mingnt=2 resources: memory:f0000000-f3ffffff memory:d1000000-d1ffffff

  Read the article

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• Microsoft Lowers Cloud Barrier To Entry

  - by Herve Roggero

  Once in a while, the technology stack changes enough to create a disturbance in the IT industry. Microsoft did just that today and has officially closed the gap with its #1 competitor: Amazon. What is remarkable is that Microsoft is no longer an alternative to Amazon, it is becoming a clear leader in that space. Some of the new features include official support for durable Virtual Machines with high availability (cross-geographic replication), free WebSites to try Azure, MySQL database at no charge, a new distributed low-latency cache feature, Linux support, support with existing VPN hardware for seamless on-premise integration, a new partner ecosystem and much, much more. Amazon had an edge against Windows Azure in the IaaS (Infrastructure as a Service) space, until now. With the latest release from Microsoft Azure, the gap has been filled. In fact, it seems Amazon may now have a gap to fill… This is great news to everyone; it seems that cloud offerings are becoming more standardized with the more mature cloud providers, and the management stack and quality of service of each cloud provider is increasingly becoming the differentiator. With today’s announcements, it is becoming clear that cloud providers are pushing hard to increase their service footprint and lowering typical barriers to entry such as support for open-source operating systems, free trial offers, higher availability, faster deployment times and simpler enterprise integration.

  Read the article

• How do I 'see' an external USB drive connected directly to my Broadband Router?

  - by The Cougar Kid

  This is a very frustrating problem! I have a small home network with several dual boot Ubuntu / Windows computers. I have recently upgraded my Broadband connection and the new router permits the direct attachment of an external USB drive which can back up all of the household's computers. There are no problems when booted under Windows, and there were no problems with older versions of UBUNTU, but since upgrading to 11.10 I can no longer "see" the drive. I used to find it via Network / Windows Network / Home / name of Router, but under 11.10 the same method yields an error message Unable to mount location Failed to retrieve share list from server. Can anyone help please? Starting Nmap 5.21 ( http://nmap.org ) at 2011-12-21 10:06 GMT Stats: 0:02:02 elapsed; 0 hosts completed (1 up), 1 undergoing Service Scan Service scan Timing: About 50.00% done; ETC: 10:10 (0:01:56 remaining) Nmap scan report for 192.168.1.254 Host is up (0.0097s latency). Not shown: 998 filtered ports PORT STATE SERVICE VERSION 554/tcp open rtsp? 7070/tcp open realserver? Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 152.38 seconds sudo tail -n 30 /var/log/syslog [sudo] password for alaric: Dec 21 10:05:42 UPSTAIRS2U wpa_supplicant[882]: WPA: Group rekeying completed with 00:01:3b:8b:63:1a [GTK=TKIP]

  Read the article

• I have problem on 12.10 64bit with nvidia graphics driver opensource and proprietary ! Can't change resolution on 3d games

  - by digitalcrow

  I have problem with nvidia graphics driver opensource and proprietary ! Can't change resolution on 3d games and there's a bug there are no kernel sources installed and thus jockey can't install proprietary drivers. I can't change resolution while on games fullscreen. I tried to install proprietary driver and i couldn't plus i couldn't login to ubuntu it showed only the desktop photo no dash no nothing. -tried to install kernel sources and blacklist+remove Nouveau drivers and then installed the proprietary drivers i hope succesfully. -The problem is the same i can't change resolution on 3d games while on fullscreen. I've installed the sources and be able to install the proprietary nvidia drivers but the problem remains, look what i got in the output of a 3d game exited while i tried to change resolution: X Error of failed request: BadValue (integer parameter out of range for operation) Major opcode of failed request: 150 (XFree86-VidModeExtension) Minor opcode of failed request: 10 (XF86VidModeSwitchToMode) Value in failed request: 0x25b Serial number of failed request: 497 Current serial number in output stream: 499 I'm giving you more details about my system: i have an nvidia geforce gts 250 , 3,4 ghz quadcore amd phenom2 , 8gbytes of ram. The output of: sudo lshw -C display; lsb_release -a; uname -a Is the following: *-display description: VGA compatible controller product: G92 [GeForce GTS 250] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:ef00(size=128) memory:fb000000-fb01ffff No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.10 Release: 12.10 Codename: quantal Linux darkpc 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I like ubuntu's style and user interface but i hate the bad quality of work they do.

  Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >