Search Results

Search found 19200 results on 768 pages for 'xp mode'.

Page 311/768 | < Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >

• Laptop Acer Travelmate 4050 takes over 10 Mins to POST

  - by Belliez

  Hi, I am a computer tech and have received a laptop for repair. I noticed when I turned it on the laptop would not do anything for a min or two (the fan would run up and stop, power led would shine and some cd rom activity then stop). It would sit there with a black screen. Suddenly after a random number of minutes (between 1-20mins!) the Acer BIOS screen would display and POST would happen before booting into Windows XP. It has frozen in XP at various times and pointed towards a CPU fault and over heating. The fan was on its last legs, sounded like a car engine, so I replaced this. Still same issues. I next replaced the CPU like for like. Same problems. Also applied new thermal paste between the cpu and heatsink, when running the fan kicks in occasionally (not as often as I thought it would) and I left it playing mp3, online radio and updating to service pack 3 and it wouldnt freeze. shutting down ok, cold start, not ok. Waits again before showing the BIOS screen. The hard disk was also making a screaming noise (SMART test and chkdsk passed) but I also replaced this. The laptop powers up with and without the battery so dont think its a battery issue. Running out of ideas and wondered if anyone had any advice. Thanks

  Read the article

• Will these instructions work when turning of journaling on a n ext4 SSD?

  - by snowlord

  I have an Acer Aspire One with an SSD for storage. I recently installed Ubuntu on it and chose ext4 for my filesystem. Then I read that journaling on an SSD isn't the best idea, so I will try to disable journaling and I have found these intstructions (from http://fenidik.blogspot.com/2010/03/ext4-disable-journal.html): # Create ext4 fs on /dev/sda10 disk mkfs.ext4 /dev/sda10 # Enable writeback mode. This mode will typically provide the best ext4 performance. tune2fs -o journal_data_writeback /dev/sda10 # Delete has_journal option tune2fs -O ^has_journal /dev/sda10 # Required fsck e2fsck -f /dev/sda10 # Check fs options dumpe2fs /dev/sda10 |more For more performance add fstab opions: data=writeback,noatime,nodiratime i.e: /dev/sda10 /opt ext4 defaults,data=writeback,noatime,nodiratime 0 0 I will use them on my boot partition. Are there any particularly bad parts here, or are there any missing steps? Will my boot partition be fit for being on an SSD after this? Or should I consider switching to ext2, or even reinstall it all and choose ext2 at partitioning time (I'd rather not though, since I've configured quite some stuff already)?

  Read the article

• RDP problem with Vista and Windows 7 destination

  - by MadBison

  I use a server a home to host a bunch of concurrently running Hyper-V VM's with different OS's and software for testing. I have Vista on the laptop, all latest SP's and patches. The server is Server 2008 R2, fully patched. The guests are a mix of XP, Vista, Server 2008 and Windows 7. If I connect to the Win XP or Server 2008 guest using RDP, it is always good. Very quick, no speed issues. If I connect to the Vista or Win 7 guests, the response time is so slow it is unusable. Usually 6 or 8 seconds, and at times it is to long to measure! This happens from both the laptop running Vista, and the server running Server 2008 R2. Does anyone know what the issue is with RDP on Vista and Windows 7 destinations? I did read this: http://blog.tmcnet.com/blog/tom-keating/microsoft/remote-desktop-slow-problem-solved.asp and that is not the problem I have applied that change to all PC's.

  Read the article

• NIC are not advertising Correct Speeds

  - by Squidly

  I have an IBM x336 that is not advertising the proper LINK speeds. One interface is the other is not. I've tried to Force it to 1000/Full but then it just shows link down. I have confirmed the switch is set to auto negotiate like my switches. I have also changed out my Ethernet Cables. I'm at a loss where to look further. I have verified that it will connect at 1G on a different swtich. This also has happened on two different servers on the same switch. This is my output from mii-tool -v for each interface. eth0: negotiated 100baseTx-FD, link ok product info: vendor 00:08:18, model 24 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD eth1: negotiated 1000baseT-FD flow-control, link ok product info: vendor 00:08:18, model 24 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

  Read the article

• Problems with "Read Only" on a Samba share from Windows machines

  - by fistameeny

  Hi, We have a Ubuntu 10.04 Server that has a bunch of Samba shares on it that Windows workstations connect to. Each Windows workstation has a valid username/password to access the shares, which have restricted access governed by Samba. The problem we are experiencing is that Samba doesn't seem to be able to mimic the Windows way of handling "Read Only" attributes. Say I have two users, UserA and UserB, both a group called Staff - UserA creates a file that is readable/writeable by the group (ie. chmod rwxrwx---). If UserA then sets the "Read Only" flag, this changes the permissions to r-xr-x--- (i.e. no write for anyone). As UserB is in the same group as UserA, they should be able to remove the "Read Only" permission - however, they can't as Samba won't allow it. Is there a way to force Samba to allow users within the same group to remove the "Read Only" from a file not created by them? Edit: The Samba smb.conf is as follows: The share is defined in the smb.conf as: [global] log file = /var/log/samba/log.%m passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . obey pam restrictions = yes map to guest = bad user encrypt passwords = true passwd program = /usr/bin/passwd %u passdb backend = tdbsam dns proxy = no netbios name = ubsrv server string = ubsrv unix password sync = yes os level = 20 syslog = 0 usershare allow guests = yes panic action = /usr/share/samba/panic-action %d max log size = 1000 pam password change = yes workgroup = workgroup [Projects] valid users = @Staff writeable = yes user = @Staff create mode = 0777 path = /srv/samba/Projects directory mode = 0777 store dos attributes = Yes The folder itself looks like this: ls -l /srv/samba/ drwxrwxrwx 2 nobody Staff 4096 2010-11-04 10:09 Projects Thanks in advance, Matt

  Read the article

• Ubuntu 64bit Xen DomU Issues after upgrade from Karmic to Lucid

  - by Shoaibi

  I was upgrading my servers today and it all went fine except the last machine which has the following issues: [Resolved using http://www.ndchost.com/wiki/server-administration/upgrade-ubuntu-pre-10.04#post-1004-upgradefinal-steps] No login prompt on console Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Done. [ 0.545705] blkfront: xvda: barriers enabled [ 0.546949] xvda: xvda1 [ 0.549961] blkfront: xvde: barriers enabled [ 0.550619] xvde: xvde1 xvde2 Begin: Running /scripts/local-premount ... Done. [ 0.870385] kjournald starting. Commit interval 5 seconds [ 0.870449] EXT3-fs: mounted filesystem with ordered data mode. Begin: Running /scripts/local-bottom ... Done. Done. Begin: Running /scripts/init-bottom ... Done. Also tried by pressing ENTER and CTRL+C many times, no use. Resolved: [/tmp was mounted as noexec, changing that fix it]: I get errors when i try to re-install udev in single user mode: Unpacking replacement udev ... Processing triggers for ureadahead ... ureadahead will be reprofiled on next reboot Processing triggers for man-db ... Setting up udev (151-12.1) ... udev start/running, process 1003 Removing `local diversion of /sbin/udevadm to /sbin/udevadm.upgrade' update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.32-25-server /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/fixrtc: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/ntfs_3g: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/resume: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/nfs-top/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/panic/console_setup: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/all_generic_ide: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/blacklist: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-bottom/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-bottom/ntfs_3g: Permission denied

  Read the article

• .ashx cannot find type error on IIS7 , no problems on webdev server

  - by Aivan Monceller

  I am trying to make AspNetComet.zip work on IIS7 (a simple comet chat implementation) Here is a portion of my web.config. <system.web> <httpHandlers> <add verb="POST" path="DefaultChannel.ashx" type="Server.Channels.DefaultChannelHandler, Server"/> </httpHandlers> </system.web> <system.webServer> <handlers> <add name="DefaultChannelHandler" verb="POST" path="DefaultChannel.ashx" type="Server.Channels.DefaultChannelHandler, Server"/> </handlers> </system.webServer> When I publish the website on my localhost IIS7 I receive an error: POST http://localhost/DefaultChannel.ashx 500 Internal Server Error Could not load type 'Server.Channels.DefaultChannelHandler The target framework of this project is .Net 2.0 I tried the Classic and Integrated Mode application pool for .Net 2.0 with no luck. I also tried converting the project to 4.0 and tried the Classic and Integrated Mode application pool for .Net 4.0 with no luck. I also tried adding the managed handler through IIS Manager's Handler Mappings. If you have time please download the source (184kb) to reproduce the problem on your own machine. The zip contains a VS2010 solution (.Net 2.0). You could also try to convert this to .Net 4.0 I am using Windows 7 anyway if that matters. If you need more details, please drop your comments below. This is working fine by the way on my webdev server.

  Read the article

• Keyboard issue when using kitty+puttycyg but not when using putty or cygwin alone

  - by kamaradclimber

  I would like to use a unique way to use console on my windows setup. Previously I used putty for remote access to linux servers and cygwin to have unix-like tools on windows. Then I discovered kitty which is a patched putty and have added the puttycyg patch. It provides the same way to connect to remote and local console. However, there is a strange behavior using vim when connected to the local console (using the puttycyg patch) : keys display A/B/C/D and replace the current character by these letter. In insert mode it does replace the caracter, in normal mode, no modification is made to the document even if the caracter is displayed as replaced. For instance, when I type : fixed bug with product deleted I get : fixed bbug wiwith prprodudueleteted I have read a lot of questions about this type of issue 3, 4 and googled it but there is no answer that work for me. The issue is present only for the setup kitty+puttycyg patch : cygwin alone works perfectly (and putty alone works also for access to linux servers). Any help would be appreciated !

  Read the article

• Samba Public and "Dropbox" folder

  - by cb0

  I want to create a special Group Directory structure for my Users. /home/groupA <-- home folder for groupA where every user of groupA can create/edit/delete files /home/groupA/Public <-- Public Folder where every user can read files /home/groupA/Public/Dropbox <-- Folder where every user can write files but only users of groupA can access this directory and create/edit/delete files Now I have: 4 drwxrwx--t 10 nobody groupA 4096 Feb 18 15:44 /home/groupA 4 drwxrwxr-x 7 nobody groupA 4096 Feb 18 15:40 /home/groupA/Public/ 4 drwxrwx-w- 10 nobody groupA 4096 Feb 18 15:55 /home/groupA/Public/Dropbox My smc.confcontains the following entrys [groupA] path = /home/groupA comment = Folder for users of groupA browseable = yes read only = no create mask = 0770 directory mask = 0770 force group = groupA [groupA Public] path = /home/groupA/Public comment = Admins Public Browseable = yes write list = @groupA create mask = 0775 directory mask = 0775 [groupA DropBox] path = /home/groupA/Public/Dropbox comment = groupA Dropbox read only = no valid users = @groupA browseable = yes inherit owner = yes directory mode = 3770 force directory mode = 3770 The working part is: Users of groupA can access and fully use /home/groupA All Users can access /home/groupA/Public/ and read the files from there. My problem is that all users, even those who are not in groupA can access the /home/groupA/Public/Dropbox and see all files. I just want them to be able to put files in there but not see the content of the folder and prohibit them from deleting any files in there. Does anybody have a clue what could be the problem and how I can fix it ?

  Read the article

• Which is more secure: Tomcat standalone or Tomcat behind Apache?

  - by NoozNooz42

  This question is not about performance, nor about load-balancing, etc. Which would be more secure: running Tomcat in standalone mode or running Tomcat behind apache? The thing is, Tomcat is written in Java and hence it is pretty much immune to buffer overrun/overflow (unless a buffer overrun in a C-written lib used by Tomcat can be triggered, but they're rare [the last I remember was in zlib, many many moons ago] and one heck of a hack to actually exploit), which gets rid of a lot of potential exploits. This page: http://wiki.apache.org/tomcat/FAQ/Security has this to say: There have been no public cases of damage done to a company, organization, or individual due to a Tomcat security issue... there have been only theoretical vulnerabilities found. All of those were addressed even though there were no documented cases of actual exploitation of these vulnerabilities. This, combined with the fact that buffer overrun/overflow are pretty much non-existent in Java, makes me believe that Tomcat in standalone mode is pretty secure. In addition to that, I can install both Java and Tomcat on Linux without needing to be root. The only moment I need to be root is to set up a transparent port 8080 to port 80 forwarding (and 8443 to 443). Two iptables line as root, that's all root is needed for. (I don't know for Apache). Apache is much more used than Tomcat and definitely does not have a security track record as good as Tomcat. What would make Tomcat + Apache more secure? What would make Tomcat + Apache less secure? In short: which is more secure, Tomcat standalone or Tomcat with Apache? (remembering that performance aren't an issue here)

  Read the article

• Computer won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• USB Device Not Recognized

  - by Franky Chanyau

  Ok this one gets a little bit complicated but bare with me :D A client brought her computer in to be fixed about a week ago, she says she tried charging a new phone she bought from china and immediately after her usb keyboard and mouse stopped working (typical). I had a quick look at it but because I did not have time, I did a simple system restore and it seemed as if the issue was fixed. I promptly sent it back to her but a few days back she called saying that the issue has returned. Turns out the computer was riddled with some virus that also corrupted her XP install so I had to format the whole thing(yes I tried repairing). I hoped that the format would fix the keyboard and mouse issue but the whole thing has escalated and the computer will throw the "USB Device not recognized" error when I plug anything into the many usb ports it has. I have installed all the drivers (including the chip set drivers) for the pc and even tried the unplugging from the power for a while trick, still no luck. I am sure it is not a hardware issue, but may be wrong. This is way over my head. Can anyone help? Computer: HP Compaq DC7100, Intel Pentium 4, 512mb RAM OS: Windows XP Professional SP2

  Read the article

• Sometimes, Synaptics Touchpad Tends Cursor to Top-Right Corner

  - by John Chadwick

  This has been a reoccurring issue for me, pretty much since I've owned this laptop (an ASUS G60JX.) Sometimes, the cursor will stop working properly and instead tend toward the top right of the screen. Basically, sometime into my usage (maybe after a couple hours) the touchpad will inevitably begin to malfunction, where it has confusing patterns of pushing the mouse cursor toward the top right of the screen. In addition, certain features (like momentum) seem to quit working entirely. It makes using the cursor extremely difficult. I've been having this issue across very many drivers. Pretty much as soon as multitouch came into the mix, although I don't believe multitouch has anything to do with it. It appears that, in the state of malfunction, it doesn't matter how you touch the touchpad, but where you touch it. Certain regions do not seem to trigger the cursor to move to the top right corner. In fact, no specific region seems to, but some areas do so more often than others. The issue can be resolved temporarily by putting the computer into sleep mode and awakening it. I have found no way to recreate this success without sleeping the computer or rebooting. Disabling and re-enabling the touchpad device does not do anything to resolve the problem. This issue does not affect my WACOM tablet nor any USB mice, and can be resolved (not to my satisfactory) by uninstalling the touchpad drivers. I'm looking for a solution, or at least a workaround that doesn't require sleep mode.

  Read the article

• Server nearly unusable when doing disk writes

  - by Wikser

  My question closely relates to my last question here on serverfault. I was copying about 5GB from a 10 year old desktop computer to the server. The copy was done in Windows Explorer. In this situation I would assume the server to be bored by the dataflow. But as usual with this server, it really slowed down. At least I could work with the remote session, even there was some serious latency. The copy took its time (20min?). In this time I went to a colleague and he tried to log in in the same server via remote desktop (for some other reason). It took about a minute to get to the login screen, a minute to open the control panel, a minute to open the performance monitor, ... Icons were loading maybe one per second. We saw the following (from memory): CPU: 2% Avg. Queue Length: 50 Pages/sec: 115 (?) There was no other considerable activity on the server. The server seldom serves some ASP.NET pages, which became also very slow in this time. The relevant configuration is as follows: Windows 2003 SEAGATE ST3500631NS (7200 rpm, 500 GB) LSI MegaRAID based RAID 5 4 disks, 1 hot spare Write Through No read-ahead Direct Cache Mode Harddisk-Cache-Mode: off Is this normal behaviour for such a configuration? What measurements could give further clues? Is it reasonable to reduce the priority of such copy I/O and favour other processes like the remote desktop? How would you do that? Many thanks!

  Read the article

• VMWare Fusion cannot connect to the NAT connection on my Mac

  - by FFish

  I have been using VMWare Fusion on my Mac to check out my websites on localhost. Now I can't connect anymore with the NAT connection. There seems to be a problem with my IP address or Mac address? I have no idea what causes this, it was working fine before!? In the XP (SP2) VM, in the taskbar I see the Local Area Connection with the yellow warning icon. The bubble says: "This connection has limited or no connectivity. You might not be aisle to access the Internet or some network resources. For more information, click this message." Doing that opens up the Local Area Connection Status panel. In the Support tab, when I click the repair button I get following message: "Windows could not finish repairing the problem because the following action cannot be completed: Renewing IP address." I tried disabling my firewall and also XAMPP that I use as server on OSX. VMWware version: 3.1 VM: XP SP2 Mac OSX 10.6.3 Any help would be greatly appreciated.

  Read the article

• Disabling drop shadows around windows or the menu bar

  - by Lri

  Nocturne can disable most shadows, but only in night mode. There's an annoying flash whenever it switches to night mode. (Eg when it's launched.) Also, it doesn't remove the shadow on the menubar. Sympa at MacThemes forums has posted a .psd file with a layer that cancels out the shadow under the menu bar. However it only works if that area of the desktop picture has a low enough brightness. Applications that cover the desktop (like DeskShade) also cover the menu bar's shadow. It's not a real solution though. Unsanity's ShadowKiller stopped working in 10.5. (The website still says NOT compatible with Mac OS X 10.6 Leopard. ;)) WindowShade X doesn't have any shadow-tweaking features anymore. Being able to decrease the shadow radius would be fine as well. osx - How do I decrease the window shadow in Mac OS X? - Super User doesn't have any solutions though. No, I don't mean defaults write com.apple.screencapture disable-shadow -bool yes. This seems like something that might just be possible without any extra applications. Or at least something that other applications besides Nocturne should support. So does anyone know any better solutions?

  Read the article

• windows 7 update freeze - what to do?

  - by Tom Tom

  Hi, yesterday I shuted down my notebook and windows 7 Ultimate started to install the automatic update. After one hour I noticed that the update is still running. I thought ok, I go to sleep and let it run. In the morning it was still running. Thus I thought it is crashed. Forced a shut-down of the notebook, and restarted it. With the same effect that the notebook is "freezing" at "Install Update 1 of 5". It does not look like whether it is chrased. The progress wheel is still moving. But it does not make any progres.. Thus somehow like crashed. Would appreciate any help! Edit: Ok was able to log-in in "save" (german: abgesicherter) mode. This way I passed to install update screen. I do not want to generally disable updates. What can I do to not install the last update, which is creating troube. Or how can I find out whats the problem with the last update? Edit2: Ok starting in save mode and finally installing the updates manually solved the problem.

  Read the article

• Multiple Devices connecting to VPN on CentOS server

  - by jfreak53

  I am looking for a solution as to what would be the VPN software for multiple OSes and Devices. I currently have 15 systems to connect to a VPN. I was using Hamachi from LogMeIn but their lack of Android support really upsets me, and their limited support for Linux OSes is also a let down. 90% of my systems are Ubuntu 11+ systems, only 2 are Windows XP. But I also have a few people, maybe 3 that need to connect to it from Android devices. This is where Hamachi has let me down and I want to move to my own VPN solution. The server would be a simple VPS running CentOS. So I need some VPN software that allows connection of those to a Linux based server. I wanted to go with OpenVPN, but I am under the opinion that in any OS you have to have their software to connect to the VPN. Ubuntu supports VPN's out of the gate, but OpenVPN requires extra software to be installed, I don't want this if I can help it. Same with Windows and same with Android. Plus android mostly requires rooted devices for OpenVPN, at least from what I've read. I was looking at maybe L2TP, but I'm not sure how easy it is to get Ubu systems connected with it as I haven't found much on the subject, let alone Window's XP machines. I know Android connects out of the gate to it. I don't know much about L2TP but I know it's a pain to get running in CentOS from what I have read. Now the last option is some sort of software for PPTP but I've never read anything on it and don't know if all systems are compatible with it. What would be your solution to these devices and multiple OSes? OpenVPN seems to be my heading I just don't like it that it always requires software to run and rooted Android Devices. Any solutions for this and install solutions? Maybe a different OS for the server like Ubuntu would make another type of VPN easier?

  Read the article

• How do I prevent spawning of zombie-like apache2 processes on Dreamhost VPS?

  - by Jonathan Hayward

  I have had a website for months or longer on a DreamHost VPS, and I have had vague memories on, in initial setup, having to turn off some customized Apache under /dh to get a standard Apache 2.x to work with. Things have been going along on an even keel, when I started making some changes lately and I found that when I tried to bounce Apache (/usr/sbin/apachectl restart), it couldn't bind to port 80, and my site had been converted from a big literature site to a small parking site. I tried to see what was listening on 80, and it was a DreamHost-customized Apache that had spawned. I killed all of them, restarted Apache, and changed the parent directory under /dh to mode 000. That was a day or two ago. I was bouncing Apache again in trying to get a new site to load under HTTPS, and I found that once again DreamHost's apache had spawned, from the directory I set to mode 000, and once again converted my site to a parking page. I renamed the directory, but I am very skeptical of whether I have permanently killed the DreamHost-customized Apache. Besides duct tape options like a crontab to kill and delete each minute, how can I permanently turn off the Apache processes that are spawning from a location under /dh and interfering with standard Apache? What should I be doing that I am not? Can DreamHost's technical support stop the interference? Thanks,

  Read the article

• esxi 5 monitoring

  - by user134880

  I'm new to esxi/vmware world. Have few question about monitoring esxi host. Now I'm using trial versian esxi 5.1 I can see performance charts in vShpere client. Cool. But I want to export this raw data (raw - I mean cvs,txt or some format which I can parse later) to other server to be able to parse this data later and create custom charts. (please do not advise to try vCenter, I need custom charts etc.) I could run esxtop in batch mode and use this data... But... How does vShpere client performance charts work? Where client takes data for charts? So if I will use esxtop batch mode it will add extra load to server. Is it possible to use same source as vSphere client use for charts? There is /var/lib/vmware/hostd/stats/hostAgentStats-20.stats file. Its looks like it is binary format. As I understood it is exactly data which I need?!?! Any ideas how to parse it? Thanks! PS: maybe some one know where to find, if there is one, info about processes running on esxi host?

  Read the article

• Can I still restore partition table?

  - by Johannes Lund

  Once I was going to resize partitions on my Mac HD from Bootcamp. I changed my mind and was going to quit, but apparently I hit a button, which made every single mac partion dissapear, and windows 7 refused to restart and be reinstalled. The 1 TB large HD consists of 3 partions, I believe. Since I can't see their actual size (except bootcamp), this is how I recall it. Macintosh HD about 500GB (Somewhere around 700GB according to disk utillity, but 500 according to Finder, and 500GB was all I could access.) Lion Recovery disk Bootcamp 293.36 GB To fix this I connected my mac via target disk mode to a pc and ran TestDisk. However this is the results: Since I Don't have 10 reputation I cant post the image showing the testdisk results, so I post a link instead hoping it is ok. The two mac partitions' sizes are completely wrong, and BOOTCAMP isn't showing. I tested using disk utilities from the snow leopard dvd. There there is one 293.36 GB Mac OS Extended partition. Before I had the firewire cable for target disk mode I tried reinstalling windows. Without success I tried again formating BOOTCAMP. Was that a bad thing to do? Could it have overwritten data from Macintosh HD? Unfortunately I have no backup. I could bring it to some kind of computer repair firm though.

  Read the article

• I/O Error on LG GSA-H12N DVD drive on Windows 7

  - by Ashwin

  I am facing an I/O Error when I try to burn DVD data discs on my LG GSA-H12N DVD drive on Windows 7. Note that I was able to do this same operation on the same hardware/software just a day earlier without any problems, but with Windows XP. The only change (AFAIK) has been the installation of Windows 7 to replace Windows XP on this PC. Here is the error I get when I try to burn a DVD data disc using CDBurnerXP 4.2.7.1801: Burning error occured An error occured while burning the disc. Most likely the disc is not usable. Usually these errors happen if the inserted media is not compatible to the drive or of poor quality. (devNTSPTI_IO_Error) Could not write to Disc (LBA: 52864 Length: 32). SCSI Pass-through Interface I/O Error. - 0xFF045D Note that there can be no problem with the discs since I have been using the same discs (from the same box) just before the Windows 7 installation with no problems. The only change has been Windows 7. I tried InfraRecorder v0.5 and ImgBurn v2.5 and got similar I/O errors: Note that Windows 7 lists the LG GSA-H21N drive as being compatible (see this link). I also checked the LG Drivers website and using the firware update from there updated the drive firmware from version UL01 to UL02. But, even this has not helped. The drive reads DVDs without any problem, but continues to produce coasters. Could someone help me figure out what is the problem? Thanks :)

  Read the article

• Windows Firewall Software to Filter Transit Traffic

  - by soonts

  I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

  Read the article

• Timeout option not working on efi windows 7/windows8 dual boot machine

  - by Guenter

  I hav a gigbyte GA-Z77m-D3h mobo and installed Windows 8 Pro and Windows 7 Ultimate on two SSDs (in that order) in EFI mode. Now when I start my computer, I get the windows boot menu (text mode) with the two OSses to choose, but I have to manually press RETURN to have the computer boot into the Win OS. Even if I wait an hour, no default action takes place. Using bcdedit (from either of the OSses) I can successfully change the time out value, and it shows up in the bcdedit (no params) output. But it doesn't fire ... Here is my current BCDEdit output (headers are in German, but values should be readable): Windows-Start-Manager --------------------- Bezeichner {bootmgr} device partition=O: path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale de-DE inherit {globalsettings} integrityservices Enable default {default} resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} displayorder {default} {current} {5ad2802a-c60a-11e2-acdb-80331c501b11} {5ad28028-c60a-11e2-acdb-80331c501b11} {5ad28029-c60a-11e2-acdb-80331c501b11} toolsdisplayorder {memdiag} timeout 5 displaybootmenu Yes Windows-Startladeprogramm ------------------------- Bezeichner {default} device partition=W: path \Windows\system32\winload.efi description Windows 7 locale de-DE inherit {bootloadersettings} recoverysequence {5ad2802e-c60a-11e2-acdb-80331c501b11} recoveryenabled Yes osdevice partition=W: systemroot \Windows resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} nx OptIn Windows-Startladeprogramm ------------------------- Bezeichner {current} device partition=C: path \Windows\system32\winload.efi description Windows 8 locale de-DE inherit {bootloadersettings} recoverysequence {5ad28033-c60a-11e2-acdb-80331c501b11} integrityservices Enable recoveryenabled Yes isolatedcontext Yes allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \Windows resumeobject {5ad28031-c60a-11e2-acdb-80331c501b11} nx OptIn bootmenupolicy Standard hypervisorlaunchtype Auto (this output is from Win8; the Win7 looks nearly identical) If maybe the problem comes from a bad EFI Windows boot manager installation, can this be fixed without loosing my windows installations?

  Read the article

• Solid State Drive Occasionally Freezes For A Minute While OS Is "Beach Balling"

  - by Boris_yo

  Almost a month ago I bought Intel 330 128GB solid state drive, migrated my data with Intel branded limited-feature Acronis from old HDD to new SSD, optimized with Intel Toolbox and started using it. Occassionally I get close to 1 minute freezes while seeing operating system "beach balls" and animations still work, I can interact and click on something but nothing responds, nothing loads. Recently a couple of such freezes occurred in shorter amount of time in a row. I have noticed that if I stop interacting with laptop, the freeze lasts less time than if I was interacting with laptop. But the bigger problem is when freeze just does not end and computer keeps being stuck unlil it is more than half hour and I run out of patience to keep waiting and feeling I need to restart the system because I am not getting anywhere. Such freeze happened while laptop was cold booting into Windows 7. This is when freeze hang occurred and I had to restart, only later to be greeted with Windows recovery screen stating something about faiure of boot sector and asking to insert Windows repair CD. But after I restarted, Windows booted successfully and all was well. I have filmed video of freeze hang occurring in cold boot which you can see here (on video page look below for description): http://www.youtube.com/watch?v=8b7MQlcDTUs As I have mentioned in the beginning, the SSD is less than a month old but here is S.M.A.R.T statistics just in case (TRIM is enabled btw according to CrystalDiskInfo): I want to emphasize that this SSD is the only drive I have, yet it is working in RAID mode (it was enabled initially in BIOS by previous laptop's owner) on Intel Rapid Storage drivers. I am contemplating about switching to AHCI mode but want to be sure this won't cause data loss. Additionally, the stock firmware is the only firmware available currently, yet Intel does not respond to my posts in their community board. If anyone here has this SSD model or generally has experience with SSD drives, I would love to know your thoughts.

  Read the article

< Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >