Search Results

Search found 8815 results on 353 pages for 'major upgrade'.

Page 313/353 | < Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >

• Get 5.1 surround sound from computer through a VCR config?

  - by Wedding Nails

  I'm posting to see if my idea of this setup is right and can be done. I currently have the following "equipment": a JVC VCR -quite old-, which has built in surround sound (aka it has several speaker outputs, which I believe is 5.1 and are connected to several speakers that are in every corner of the room), a computer with SPDIF optical output and a new flat screen TV (with built in HDMI). I want the computer to take advantage of the VCR's surround system (all the speakers in the room) in order to play mainly music and video always with all the speakers (5.1) and with the maximum sound quality. Currently, the computer plays sound only through the front speaker (I connect one output to the on board pc audio input) and the quality is really bad. As a side note, the computer video runs with S-video (old school), and the picture quality as you would imagine, is really bad with the new big LCD screen. My main goals are: to upgrade the picture with a new video card which would support HDMI (my tv has HDMI). to buy a SPDIF optical cable, connect one end to the VCR SPDIF input and the other end to the PC output This is theoretically what I've researched so far, and I came out with several questions: in this case, with the SPDIF cable connected, and all the configurations done in windows allowing the 5.1, will I get every content I play "converted" or played through all of my speakers? (I read this forum post). I already know that in order for this setup to play from all the speakers, the content/audio source has to be 5.1. but my question is, if there is a way to play from all of the speakers no matter what type of content I'm playing (that's why I said conversion there) I already know that HDMI cables carry digital sound. Is there a way I can only use said HDMI cord to the tv, and get sound through the VCR? (I'm not too sure about this, I would have to disable the TVs speakers and use the VCR surround as default, but I have no clue wether this can be done or not). Update: The ultimate question is, do I really have to rely on "sound virtualization" technology to get sound from all the speakers, no matter what content I play? (do I require a newer sound card, like a creative soundblaster with said technology?) Thanks!

  Read the article

• BUILDROOT files during RPM generation

  - by khmarbaise

  Currently i have the following spec file to create a RPM. The spec file is generated by maven plugin to produce a RPM out of it. The question is: will i find files which are mentioned in the spec file after the rpm generation inside the BUILDROOT/SPECS/SOURCES/SRPMS structure? %define _unpackaged_files_terminate_build 0 Name: rpm-1 Version: 1.0 Release: 1 Summary: rpm-1 License: 2009 my org Distribution: My App Vendor: my org URL: www.my.org Group: Application/Collectors Packager: my org Provides: project Requires: /bin/sh Requires: jre >= 1.5 Requires: BASE_PACKAGE PreReq: dependency Obsoletes: project autoprov: yes autoreq: yes BuildRoot: /home/build/.jenkins/jobs/rpm-maven-plugin/workspace/target/it/rpm-1/target/rpm/rpm-1/buildroot %description %install if [ -e $RPM_BUILD_ROOT ]; then mv /home/build/.jenkins/jobs/rpm-maven-plugin/workspace/target/it/rpm-1/target/rpm/rpm-1/tmp-buildroot/* $RPM_BUILD_ROOT else mv /home/build/.jenkins/jobs/rpm-maven-plugin/workspace/target/it/rpm-1/target/rpm/rpm-1/tmp-buildroot $RPM_BUILD_ROOT fi ln -s /usr/myusr/app $RPM_BUILD_ROOT/usr/myusr/app2 ln -s /tmp/myapp/somefile $RPM_BUILD_ROOT/tmp/myapp/somefile2 ln -s name.sh $RPM_BUILD_ROOT/usr/myusr/app/bin/oldname.sh %files %defattr(-,myuser,mygroup,-) %dir "/usr/myusr/app" "/usr/myusr/app2" "/tmp/myapp/somefile" "/tmp/myapp/somefile2" "/usr/myusr/app/lib" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/start.sh" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/filter-version.txt" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/name.sh" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/name-Linux.sh" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/filter.txt" %attr(755,myuser,mygroup) "/usr/myusr/app/bin/oldname.sh" %dir "/usr/myusr/app/conf" %config "/usr/myusr/app/conf/log4j.xml" "/usr/myusr/app/conf/log4j.xml.deliver" %prep echo "hello from prepare" %pre -p /bin/sh #!/bin/sh if [ -s "/etc/init.d/myapp" ] then /etc/init.d/myapp stop rm /etc/init.d/myapp fi %post #!/bin/sh #create soft link script to services directory ln -s /usr/myusr/app/bin/start.sh /etc/init.d/myapp chmod 555 /etc/init.d/myapp %preun #!/bin/sh #the argument being passed in indicates how many versions will exist #during an upgrade, this value will be 1, in which case we do not want to stop #the service since the new version will be running once this script is called #during an uninstall, the value will be 0, in which case we do want to stop #the service and remove the /etc/init.d script. if [ "$1" = "0" ] then if [ -s "/etc/init.d/myapp" ] then /etc/init.d/myapp stop rm /etc/init.d/myapp fi fi; %triggerin -- dependency, dependency1 echo "hello from install" %changelog * Tue May 23 2000 Vincent Danen <[email protected]> 0.27.2-2mdk -update BuildPreReq to include rep-gtk and rep-gtkgnome * Thu May 11 2000 Vincent Danen <[email protected]> 0.27.2-1mdk -0.27.2 * Thu May 11 2000 Vincent Danen <[email protected]> 0.27.1-2mdk -added BuildPreReq -change name from Sawmill to Sawfish The problem i found is that the files (filter.txt in particular) after the generation process on a Ubuntu system but not on SuSE system. Which might be caused by different rpm versions ? Currently we have an integration test which fails based on the non existing of the file (filter.txt under a buildroot folder?)

  Read the article

• How to properly shutdown a Linux VMware Server Host

  - by Mikee

  Hi Everybody: In our lab, we have a server running Ubuntu Linux 8.04.4 x64, with VMware Server 2.1 hosting 4 VM's. I have a major concern with regards to shutting down the host server. Mostly, how do I ensure that the guest VM's are being shut down safely? In the VMware web interface console, I have enabled: "Allow virtual machines to start and stop automatically with the system" I enabled the Default Startup Delay for 15 seconds along with the "Start next VM immediately if the VMware Tools start" option checked I enabled the Default Shutdown Delay with a 60 second shutdown delay and a Shutdown Action of "Shut Down Guest" All VM's have the VMware Tools installed and properly working. All VM's are moved up into the "Specified Order" section of "Startup Order", thus when powering the server back on, all those VM's should start up again in that specified order. When I went to shut down the server, I used the shutdown -h now command. Based on the settings I entered above, I was expecting a 4 minute shutdown, as there is an option to delay the shutdown of each VM by 60 seconds. However, that is not what happened. Instead, the server shutdown in under a minute. When I powered the server back on, only 2 VM's properly loaded. The other 2 showed the following error: "Power on Virtual Machine" failed to complete If these problems problems persist, please contact your system administrator. Details: Cannot open the disk '[location to .vmdk]' or one of the snapshot disks it depends on. Reason: Failed to lock the file. Obviously, if this error occured, then it is clear to me that the VM's were not properly shutdown, or the server powered off before the VM's were completely shutdown. I have fixed the above error by deleting the .lck files in the respective VM directories. How would I know if the VM's were properly shut down? I checked the VMware-server logs, but they only seem to display the logs of when the vmware-mgmt service is running in the current session. I'm mostly running Linux VM's, so is there an easy way to know whether or not a server was properly shut down in Linux? Thank you all for the help!

  Read the article

• Need Windows XP VGA driver for i3 Haswell

  - by AFH

  Background: I have recently upgraded my hardware because the previous Pentium system started failing to the point that it would not run long enough to boot. It was obviously a hardware fault, but I had no way of knowing whether it was in the motherboard, CPU or memory. Not all the components were now available, so I decided to replace all three. In order to get some benefit from the expenditure, I though I would put in faster components, and for future-proofing went for recently released ones: MSI Z87-G41-PCMate and Intel i3-4130 with 4400 HD graphics. The system performs excellently with Ubuntu 13.10, so I know there are no hardware problems, but I need to continue running XP because it runs several thousand pounds (UK) worth of software, which meets my needs more than adequately: in some cases there is no longer support for later Windows releases, and in most others an expensive and to me unnecessary upgrade is required. Problem: The motherboard specifications claim Windows XP support for the live driver update utility, which misled me into believing that XP drivers were available. Not true: Intel have apparently refused to provide XP drivers for Haswell chips. The update program runs on XP, but finds no suitable Intel drivers. The system is more or less running on the default fail-safe VGA driver, but DirectX will not load, which stops a number of my applications from running. I have been trawling the internet for a month now, but I have not found a graphics driver which will load successfully: all show "This device cannot start. (code 10)". I don't need HDMI support: my monitor is 1280x1024 and connected through the VGA port, so all I need is a driver which will handle this resolution well enough to support DirectX. Has anyone found a driver which will do this? Please don't reply with information found from internet searches, unless you have actually solved this problem: be assured that I have been all round the houses looking at solutions which others have reported as working, but none of them does for me. Incidentally, I did find an Intel HD sound driver which XP accepts (winxp_145111.exe from Intel), though without connecting to an HDMI port on a TV or sound system I have no idea if it works in practice. However, the graphics section of the same driver fails, like all the others I've tried.

  Read the article

• Problems updating to Windows 8.1

  - by user52428

  yesterday I attempted to upgrade to windows 8.1 from windows 8. My brother downloaded it on his computer the day before then. I got it from the Windows store. It downloaded and prompted me to restart so I did. It just had the windows 8 loading screen with the HP sign above it, no percentages or anything else, I waited for about 2 hours and while I was waiting I did some research. After reading I saw it could take 20 minutes to an hour to update, but it had already been 2 hours. I read another article and it said someone restarted their computer and it restored to windows 8.0. That's what I did and it worked. So I tried again and the same thing happens, so instead of waiting I decided I would just restart it again. I tried again and this time it showed a percentage it said,"Setting Up" After it reached 100% it went back to what happened before HP sign and just loaded again, I thought it would be different this time because it did show percentages. I waited an hour and nothing happened so I restarted the computer again. This time when I restarted it, it didn't restore, so I turned the laptop of for around 30 minutes turned it back on and it said,"Attempting to restore to previous version of Windows" It said that for around 10 minutes and it restored, so I shut downed my computer for an hour and did some more research, later I found that I needed to update my drivers my drivers we're updated so I did some more research after this I saw I needed to search for updates via: SettingsChange PC settingsWindows Update. It said I already had automatic updates on, I decided to check for updates and it said there was one update scheduled for Saturday. I didn't think this could change anything so I updated what I could. I tried to install it again it was around 11:30 last night when it was done downloading and it prompted me to restart but I had gone to sleep. I woke up today and saw it showed the HP sign and loaded again. I tried restarting it again but this didn't work I had to shut it of for 30 minutes and try again and it worked. So now I'm posting this seeing If I can get any help with this problem. Any help is appreciated. Thanks!

  Read the article

• ubuntu 8.04lts + rdiff-backup: Should I install from source instead of using apt repositories?

  - by egarcia

  I'm trying to use rdiff-backup in order to make backup copies of some folders inside an Ubuntu 8.04LTS server. I'm attempting to do the backup on another server with a more modern Ubuntu distro (9.10). I'll call this one the "client". rdiff-backup needs to be installed on both the client and the server. It is available on the apt repositories on both machines, so I installed it using sudo apt-get install rdiff-backup. The problem is that the version installed on the server is older than the one on the client (1.1.15 vs 1.2.8). Thus I get errors when I try do make them work together. So I need both versions to be the same. What is the standard procedure in these cases? Should I attempt to upgrade the version on the server, or downgrade the version on the client? And how whould I do that? In case it is useful, I'd like to point out that the rdiff-backup apt-package has some dependencies - librsync1 & python-support Attaching the errors I got in case they help: rdiff-backup egarcia@test::/var/rails/ohwr/backup /home/kikito/backup/files Warning: Local version 1.2.8 does not match remote version 1.1.15. Exception ' Warning Security Violation! Bad request for function: rpath.make_file_dict with arguments: ['/var/rails/ohwr/backup'] ' raised of class '<class 'rdiff_backup.Security.Violation'>': File "/usr/lib/pymodules/python2.6/rdiff_backup/Main.py", line 304, in error_check_Main try: Main(arglist) File "/usr/lib/pymodules/python2.6/rdiff_backup/Main.py", line 321, in Main rps = map(SetConnections.cmdpair2rp, cmdpairs) File "/usr/lib/pymodules/python2.6/rdiff_backup/SetConnections.py", line 78, in cmdpair2rp return rpath.RPath(conn, filename).normalize() File "/usr/lib/pymodules/python2.6/rdiff_backup/rpath.py", line 884, in __init__ else: self.setdata() File "/usr/lib/pymodules/python2.6/rdiff_backup/rpath.py", line 908, in setdata self.data = self.conn.rpath.make_file_dict(self.path) File "/usr/lib/pymodules/python2.6/rdiff_backup/connection.py", line 450, in __call__ return apply(self.connection.reval, (self.name,) + args) File "/usr/lib/pymodules/python2.6/rdiff_backup/connection.py", line 370, in reval if isinstance(result, Exception): raise result Traceback (most recent call last): File "/usr/bin/rdiff-backup", line 30, in <module> rdiff_backup.Main.error_check_Main(sys.argv[1:]) File "/usr/lib/pymodules/python2.6/rdiff_backup/Main.py", line 304, in error_check_Main try: Main(arglist) File "/usr/lib/pymodules/python2.6/rdiff_backup/Main.py", line 321, in Main rps = map(SetConnections.cmdpair2rp, cmdpairs) File "/usr/lib/pymodules/python2.6/rdiff_backup/SetConnections.py", line 78, in cmdpair2rp return rpath.RPath(conn, filename).normalize() File "/usr/lib/pymodules/python2.6/rdiff_backup/rpath.py", line 884, in __init__ else: self.setdata() File "/usr/lib/pymodules/python2.6/rdiff_backup/rpath.py", line 908, in setdata self.data = self.conn.rpath.make_file_dict(self.path) File "/usr/lib/pymodules/python2.6/rdiff_backup/connection.py", line 450, in __call__ return apply(self.connection.reval, (self.name,) + args) File "/usr/lib/pymodules/python2.6/rdiff_backup/connection.py", line 370, in reval if isinstance(result, Exception): raise result rdiff_backup.Security.Violation: Warning Security Violation! Bad request for function: rpath.make_file_dict with arguments: ['/var/rails/ohwr/backup']

  Read the article

• Why won't vyatta allow SMTP through my firewall?

  - by Solignis

  I am setting up a vyatta router on VMware ESXi, But I see to have hit a major snag, I could not get my firewall and NAT to work correctly. I am not sure what was wrong with NAT but it "seems" to be working now. But the firewall is not allowing traffic from my WAN interface (eth0) to my LAN (eth1). I can confirm its the firewall because I disabled all firewall rules and everything worked with just NAT. If put the firewalls (WAN and LAN) back in place nothing can get through to port 25. I am not really sure what the issue could be I am using pretty basic firewall rules, I wrote the rules while looking at the vyatta docs so unless there is something odd with the documentation they "should" be working. Here is my NAT rules so far; vyatta@gateway# show service nat rule 20 { description "Zimbra SNAT #1" outbound-interface eth0 outside-address { address 74.XXX.XXX.XXX } source { address 10.0.0.17 } type source } rule 21 { description "Zimbra SMTP #1" destination { address 74.XXX.XXX.XXX port 25 } inbound-interface eth0 inside-address { address 10.0.0.17 } protocol tcp type destination } rule 100 { description "Default LAN -> WAN" outbound-interface eth0 outside-address { address 74.XXX.XXX.XXX } source { address 10.0.0.0/24 } type source } Then here is my firewall rules, this is where I believe the problem is. vyatta@gateway# show firewall all-ping enable broadcast-ping disable conntrack-expect-table-size 4096 conntrack-hash-size 4096 conntrack-table-size 32768 conntrack-tcp-loose enable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name LAN_in { rule 100 { action accept description "Default LAN -> any" protocol all source { address 10.0.0.0/24 } } } name LAN_out { } name LOCAL { rule 100 { action accept state { established enable } } } name WAN_in { rule 20 { action accept description "Allow SMTP connections to MX01" destination { address 74.XXX.XXX.XXX port 25 } protocol tcp } rule 100 { action accept description "Allow established connections back through" state { established enable } } } name WAN_out { } receive-redirects disable send-redirects enable source-validation disable syn-cookies enable SIDENOTE To test for open ports I have using this website, http://www.yougetsignal.com/tools/open-ports/, it showed port 25 as open without the firewall rules and closed with the firewall rules. UPDATE Just to see if the firewall was working properly I made a rule to block SSH from the WAN interface. When I checked for port 22 on my primary WAN address it said it was still open even though I outright blocked the port. Here is the rule I used; rule 21 { action reject destination { address 74.219.80.163 port 22 } protocol tcp } So now I am convinced either I am doing something wrong or the firewall is not working like it should.

  Read the article

• innobackupex - after restoring - quit without updating PID file

  - by clarkk

  After restoring a backup the server can't start.. restoring # tar -izxf /var/www/bak/db/2013-11-10-1437_mysql.tar.gz -C /var/www/bak/db_import # innobackupex --use-memory=1G --apply-log /var/www/bak/db_import # service mysql stop # mv /var/lib/mysql /var/lib/mysql-old # mkdir /var/lib/mysql # innobackupex --copy-back /var/www/bak/db_import # chown -R mysql:mysql /var/lib/mysql # service mysql start error log 131110 21:24:20 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 2013-11-10 21:24:21 0 [Warning] TIMESTAMP with implicit DEFAULT value is deprecated. Please use --explicit_defaults_for_timestamp server option (see documentation for more details). 2013-11-10 21:24:21 6194 [Warning] Using pre 5.5 semantics to load error messages from /opt/mysql/server-5.6/share/english/. 2013-11-10 21:24:21 6194 [Warning] If this is not intended, refer to the documentation for valid usage of --lc-messages-dir and --language parameters. 2013-11-10 21:24:21 6194 [Note] Plugin 'FEDERATED' is disabled. /usr/local/mysql/bin/mysqld: Table 'mysql.plugin' doesn't exist 2013-11-10 21:24:21 6194 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 2013-11-10 21:24:21 6194 [Note] InnoDB: The InnoDB memory heap is disabled 2013-11-10 21:24:21 6194 [Note] InnoDB: Mutexes and rw_locks use GCC atomic builtins 2013-11-10 21:24:21 6194 [Note] InnoDB: Compressed tables use zlib 1.2.3 2013-11-10 21:24:21 6194 [Note] InnoDB: Using Linux native AIO 2013-11-10 21:24:21 6194 [Note] InnoDB: Not using CPU crc32 instructions 2013-11-10 21:24:21 6194 [Note] InnoDB: Initializing buffer pool, size = 128.0M 2013-11-10 21:24:21 6194 [Note] InnoDB: Completed initialization of buffer pool 2013-11-10 21:24:21 6194 [Note] InnoDB: Highest supported file format is Barracuda. 2013-11-10 21:24:22 6194 [Note] InnoDB: 128 rollback segment(s) are active. 2013-11-10 21:24:22 6194 [Note] InnoDB: Waiting for purge to start 2013-11-10 21:24:22 6194 [Note] InnoDB: 5.6.12 started; log sequence number 636992658 2013-11-10 21:24:22 6194 [Note] Server hostname (bind-address): '127.0.0.1'; port: 3306 2013-11-10 21:24:22 6194 [Note] - '127.0.0.1' resolves to '127.0.0.1'; 2013-11-10 21:24:22 6194 [Note] Server socket created on IP: '127.0.0.1'. 2013-11-10 21:24:22 6194 [ERROR] Fatal error: Can't open and lock privilege tables: Table 'mysql.user' doesn't exist 131110 21:24:22 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended mysql_upgrade /opt/mysql/server-5.6/bin/mysql_upgrade -u root -pxxxxx -P 3308 Warning: Using a password on the command line interface can be insecure. Looking for 'mysql' as: /opt/mysql/server-5.6/bin/mysql Looking for 'mysqlcheck' as: /opt/mysql/server-5.6/bin/mysqlcheck FATAL ERROR: Upgrade failed

  Read the article

• XP Pro product keys

  - by Bill

  I have a very serious problem. After my XP Home OS was trashed by rogue software - a trial of a thing named TuneUp - I did a clean install, including HDD reformat of Windows XP Pro from a purchased OEM disk. This was Service Pack 2, subsequently upgraded to SP3. I had conclusively mislaid the product key. I had to access data on the machine VERY urgently and I did not then know that under some circumstances Microsoft might agree to provide a replacement. I found what I now know must have been a pirate key on the Net which enabled installation but NOT activation. This of course left me functional but 30 days before meltdown - about 20 days left as I write this. Various retailers want around £100 for retail with matching product key. - this would be paying twice over just to continue use on the same computer. I have neither need nor intention of installing XP Pro on any other computer. I have tried a number of applications claiming to deal with this problem but none of them work. A Belarc profile shows that the pirate key has replaced the original one on the system. I have now found two keys, one of which might be the original, but neither work. I am about to upgrade the HDD and it looks like I will just be passing the problem on when I install XP. I have retrieved a key from the disk, but it is seemingly one Microsoft use in production and does not work. It is 76487-OEM-0015242-71798. The keys I have, one of which which might or might not be the original, are CD87T-HFP4G-V7X7H-8VY68-W7D7M and FC8GV-8Y7G7-XKD7P-Y47XF-P829W (or P819W - I believe it to be the latter, but the box will not accept it). The pirate key which has enabled this install and which is now stored on the system but will not activate is QQHHK-T4DKG-74KG7-BQB9G-W47KG. In these circumstances is it likely that Microsoft would issue a replacement? Is there any other solution? I am not trying to defraud anyone, just to keep on using the product I legitimately bought. Bill

  Read the article

• CPU Lockup when loading folder of bookmarks in Firefox

  - by Gary M. Mugford

  I am running Firefox 3.6 on WinXPSP3 on a duo Core machine with 4G of memory. I am also running Avast! free anti-virus and ZoneAlarm free firewall, both latest versions. Within the last month, my service provider basically forced me to upgrade to a Docsis 3.0 compliant modem (offered me a deal I couldn't turn down). At that point, I also upgraded to FF3.6. Basically, I am not unhappy with many aspects of this switchover, EXCEPT, when I now load a folder of bookmarks (anywhere from 10 to 38) I get nothing like the load times I experienced a couple of months back. It's taking minutes rather than seconds. And the first bookmark in one of the folders, GMail, rarely loads before timing out. I have used the old trick of powering off the cable modem before my day's work. This used to fix 'load-lag' in the old days. I have switched from my ISP's DNS server to Google, OpenDNS and back. And nothing seems to work currently. It's not my DNS cache. That's been flushed and secondary computers also have the same issue when loading folders. I have watched the CPU usage and loading the folder will send VSMon (ZoneAlarm) usage over 40 percent, AVastSvc (Avast!) over 30 and Firefox will then push the needle to 100. There's a brief burst by SVCHost when the others falter in devouring cycles. Then everything subsides to single digits once the last tab is loaded. The only other nominal nastiness is VSMon ALWAYS hitting 50 percent when ANY program starts downloading content from the internet. If I shutdown ZoneAlarm (and VSMon with it), the same slow loading takes place, but this time System is running 50% plus, again driving the usage to 100 per cent. I have my doubts FF3.6 vs FF3.5 is an issue, since the other computers are still running 3.5 and suffer the same issue. Those computers are on, but inactive, most of the time, being backups. Obviously, when the CPU hits 100, I can't do much of anything in FireFox OR in other programs. Video play through WMPC or VLC is extremely choppy, although it doesn't seem to affect the audio. Any ideas what I can try next? Thanks, GM

  Read the article

• mobile broadband recommendations for Lenovo T500

  - by Justin Grant

  I use a Lenovo T500 primarily in and around San Francisco, although I do some travel in the US on business and occasionally to Europe/Asia. I'm looking for a good mobile broadband option for my T500. I am admittedly baffled by the various mobile-broadband choices (3G vs. 4G, WiMax vs. LTE vs. MIMO vs. ..., etc.). My priorities are (in this order): Compatible with Lenovo T500 and Windows 7. I realize only the AT&T accessory card is listed on Lenovo's site, but I've also heard that other cards will work in my T500 too, like the WiMax/Wifi combo card-- so I'm interested in what actually works, not necessarily only what Lenovo is promoting. Reliable coverage in US large cities, especially the SF Bay Area. my IPhone has lousy coverage in many spots, so I'd be nervous about an AT&T 3G option unless the problem is with the IPhone and not AT&T's network. I'm OK with non-great coverage outside major US cities, since I don't do much travel in those areas. Speed. faster is better. Internal card. I'd slightly prefer something I could install inside my T500 instead of a dongle on the side that might break off, although this is my lowest priority so it's not a big deal. Price. I don't want to pay over $100/month. I've tried lots of Googling and haven't come up with clear answers. I've seen lots of general overviews without recommendations, and lots of passionate opinions which don't feel objective (and don't help me understand compatibility with my hardware & geography). Can you recommend a good, objective guide online, ideally for Lenovo although general guide is OK too, which can help me figure out which option is the best one for me? I'd also be interested in your own personal experiences of using mobile broadband using a Lenovo T500. I'll accept the answer which gets me closest to making a decision.

  Read the article

• Certain Programs cannot access internet

  - by Cindy

  Operating System: Windows 7 (x64) Problem: Certain Programs are unable to access the internet. They claim that there is no connection when you already are connected. Hello, before we start. Just letting you know I'm new here, and I'm very new to Windows 7. I installed it two days ago. I just installed Windows 7 on my laptop and I have a few problems. I play World of Warcraft, as well as a variety of games. And when I first attempt to log into the game, I get a windows error message, but it doesn't stop there. I thought World of Warcraft got corrupted during the upgrade. It seems that I am unable to access the internet from other online games as well. Most say in along the lines of "Cannot connect to patch server, try again later." I cannot use a downloader Also, I have internet explorer. The x32 version of the browser cannot connect to the internet, and when I try to enter "google.com", it says the same thing. I'm only accessing this site through Internet Explorer x64, which I would have been fine with is it's compatible with Adobe Flash. The only thing that seems to connect to the internet are Internet Explorer x64 and Windows Live Messenger. Here are the steps I have taken, but none worked. 1.) Disable Windows Firewall 2.) Have Windows Firewall Enabled, but allow the specific programs to access internet. And allowed all incoming access. 3.) Disabled UAC, Ran the programs as an admin, and set compatibility to Vista. 4.) Uninstalled an anti-virus program. (McAffee Security Suite 2010) 5.) Reinstalled the programs 6.) Reinstalled Windows 7 7.) Retaken the steps on the Administrator account. Please assist me in this problem. I need to get back into the game. Thanks so much in advance.

  Read the article

• HP UX can not boot from Ignite Tape

  - by Spirit

  We have hp rp2470 server running hp-ux 11.00, with LVM mirroring. As for redundancy we have second rp2470 same hw (same two processors, same ram, same two hdd’s, same number of lan cards). I want to clone first one to the second. For that purpose I am making ignite tape with the following command: make_tape_recovery -x inc_entire=vg00 Ignite tape finishes without problems. When I boot second server from this ignate tape, server is starting to boot, and ignite restore finishes without any errors, only few notes, which are normal. However vmunix is not booting and when restore finishes, it boot to ISL prompt. From this I cannot boot /stand/vmunix. I tried to run recovery shell but no success. When recovery shell ask to do frecover to restore critical files, then I receive error: frecover(5405): unable to open /dev/rmt/0m At first I thought that the problem might be in the difference of the firmware version of the servers: fw version of production server is: Firmware Version 43.50 and fw version of backup server is: Firmware Version 42.19 So i did a fw upgrade of my backup server so that both servers are v43.50, and tried a recovery but again cant boot the system. Next I did another archive tape with -I (Interactive) flag: make_tape_recovery -I -x inc_entire=vg00 and tried recovery with it, again no good. I cannot find any error or warnings on ignite log, and I cannot boot hpux. I am only on ISL prompt. This is what i've noticed on the gsp logs: ************* SYSTEM ALERT ************** SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:18:49 ALERT LEVEL: 6 = Boot possible, pending failure - action required REASON FOR ALERT SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail LEDs: RUN ATTENTION FAULT REMOTE POWER FLASH OFF ON ON ON LED State: Boot Failed. Running non-OS code. Check Chassis and Console Logs for error messages. 0x00000060860010B0 00000000 00000000 - type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A1231 - type 11 = Timestamp 07/27/2003 10:18:49 And another gsp log: Log Entry # 3 : SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:12:20 ALERT LEVEL: 6 = Boot possible, pending failure - action required SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail CALLER ACTIVITY: 1 = test STATUS: 0 CALLER SUBACTIVITY: 0B = implementation dependent REPORTING ENTITY TYPE: 0 = system firmware REPORTING ENTITY ID: 00 0x00000060860010B0 00000000 00000000 type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A0C14 type 11 = Timestamp 07/27/2003 10:12:20 Type CR for next entry, - CR for previous entry, Q CR to quit. Please note that I can not change anything on the production server. I can only make changes to the backup server. Any help is appreciated.

  Read the article

• dd-wrt router firmware QoS troubleshooting

  - by Jeff Atwood

  I've been using the dd-wrt firmware on my router and I like it a lot! But -- I'm not sure the quality of service (QoS) is working on it. I have it set up as follows: http, port 80 -- Premium bittorrent, port 6969 -- Bulk https, port 443 -- Premium dns, port 53 -- Premium Per the QoS documentation, these levels are: bandwidth is allocated based on the following percentages of uplink and downlink values for each class: Exempt: 100mbps - ignores global limits. Premium: 75% - 100% Express: 15% - 100% Standard: 10% - 100% Bulk: 1.5% - 100% This doesn't entirely seem to work, though -- with busy torrents going I get major pauses in my web browsing which sucks! The QoS documentation gives some steps to check the QoS ... What you'll be interested to look at will be the first set of source and destination IP, including the port numbers. Next the presence of l7proto and the "mark" field. The entries indicate the current live connection QoS priority applied on them based on the "mark" field. The "mark" values correspond to the following Exempt: 100 Premium: 10 Express: 20 Standard: 30 Bulk: 40 (no QoS matched): 0 You may see "mark=0" for some l7proto service even though they are in configured in the list of QoS rules. This may mean that the layer 7 pattern matching system didn't match a new or changed header for that protocol. Custom service on port matches will usually take care of these. On port 6969 (bittorrent) I see a weird mixture of stuff with mark=0 and mark=40 like so cat /proc/net/ip_conntrack udp 17 105 src=98.162.182.42 dst=1.2.3.4 sport=64512 dport=6969 packets=3 bytes=290 src=10.0.0.2 dst=98.162.182.42 sport=6969 dport=64512 packets=4 bytes=202 [ASSURED] mark=0 secmark=0 use=1 tcp 6 117 TIME_WAIT src=98.248.173.174 dst=1.2.3.4 sport=51114 dport=6969 packets=12 bytes=704 src=10.0.0.2 dst=98.248.173.174 sport=6969 dport=51114 packets=10 bytes=440 [ASSURED] mark=40 secmark=0 use=1 tcp 6 598 ESTABLISHED src=165.132.128.201 dst=1.2.3.4 sport=57218 dport=6969 packets=8024 bytes=9919881 src=10.0.0.2 dst=165.132.128.201 sport=6969 dport=57218 packets=4211 bytes=239607 [ASSURED] mark=0 secmark=0 use=1 tcp 6 586 ESTABLISHED src=68.46.9.24 dst=1.2.3.4 sport=64688 dport=6969 packets=6 bytes=490 src=10.0.0.2 dst=68.46.9.24 sport=6969 dport=64688 packets=8 bytes=944 [ASSURED] mark=40 secmark=0 use=1 udp 17 45 src=222.254.228.38 dst=1.2.3.4 sport=25438 dport=6969 packets=5 bytes=454 src=10.0.0.2 dst=222.254.228.38 sport=6969 dport=25438 packets=3 bytes=154 [ASSURED] mark=0 secmark=0 use=1 ( full file visible at http://pastebin.com/AZE6EtWm ) I've been playing around with this log for a little while and I can't see any patterns! Why is some port 6969 bittorrent traffic tagged mark=0 (not matched) by dd-wrt's QoS while others are tagged mark=40 (Bulk) .. any ideas?

  Read the article

• ruby on rails gitorious setup on ubuntu

  - by dogmatic69

  Ive been trying to install gitorious for a while now which required ruby and rails etc. Ive finally got rails pages serving but cant finish the installation of gitorious because the gem version is too new. the error logs say please run 'rake ultrasphinx:configure' and that gives rake ultrasphinx:configure (in /var/www/apps/gitorious) rake aborted! uninitialized constant ActiveSupport::Dependencies::Mutex /var/www/apps/gitorious/Rakefile:10:in `require' (See full trace by running task with --trace) From searching google this is beacuse of the wrong gem verison. Cant find a way to down grade it. apparently sudo gem update --system 1.4.2 should do the trick but ubuntu 10.10 does not like this. ERROR: While executing gem ... (RuntimeError) gem update --system is disabled on Debian, because it will overwrite the content of the rubygems Debian package, and might break your Debian system in subtle ways. The Debian-supported way to update rubygems is through apt-get, using Debian official repositories. If you really know what you are doing, you can still update rubygems by setting the REALLY_GEM_UPDATE_SYSTEM environment variable, but please remember that this is completely unsupported by Debian. So i added export REALLY_GEM_UPDATE_SYSTEM=1 to .bashrc and reloaded it with . ~/.bashrc and still the same. ive tried various forms of setting this environmental variable with no luck. Ive also been told on #gitorious irc channel to add the file config/initializers/rubygems.rb with the line require "thread" to it. This has done nothing. EDIT: Just found another way which was rvm install rubygems 1.4.2 and it gave: Removing old Rubygems files... Installing rubygems dedicated to ruby-1.8.7-p334... Retrieving rubygems-1.4.2 % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 288k 100 288k 0 0 282k 0 0:00:01 0:00:01 --:--:-- 414k Extracting rubygems-1.4.2 ... Installing rubygems for /home/ubuntu/.rvm/rubies/ruby-1.8.7-p334/bin/ruby ERROR: Error running 'GEM_PATH="/home/ubuntu/.rvm/gems/ruby-1.8.7-p334:/home/ubuntu/.rvm/gems/ruby-1.8.7-p334@global:/home/ubuntu/.rvm/gems/ruby-1.8.7-p334@global" GEM_HOME="/home/ubuntu/.rvm/gems/ruby-1.8.7-p334" "/home/ubuntu/.rvm/rubies/ruby-1.8.7-p334/bin/ruby" "/home/ubuntu/.rvm/src/rubygems-1.4.2/setup.rb"', please read /home/ubuntu/.rvm/log/ruby-1.8.7-p334/rubygems.install.log WARN: Installation of rubygems did not complete successfully. TL;DR please tell me how to downgrade rubygems on ubuntu 10.10 or upgrade gitorious to work with 1.6.2 gems

  Read the article

• Lag spikes at full CPU usage, maybe video card

  - by Roberts

  I am posting this thread in hurry so few things may be missed (I will update tomorrow). My PC specs: Motherboard Name - Gigabyte GA-945PL-S3 CPU Type - DualCore Intel Core 2 Duo E4300, 1800 MHz (9 x 200) OS - Microsoft Windows 7 Ultimate OS Kernel Type - 32-bit OS Version - 6.1.7601 I bougth a new video card one month ago. GeForce 210. I didn't have any problems. I wanted to overclock it, in other words: "Play with it". So I installed Gigabyte EasyBoost from CD and overclocked the GPU 590 + 110 mhz, memory to max to 960mhz from 800mhz. Benchmarks showed a little bit bigger score. Then I overclocked shader clock from 1405 to [..] (don't remeber really). So I was playing Modern Warfare 2 when off sudden computer froze when I wanted to select team, I was afk before that. I had to reset CMOS. After that I had problems with Skype: unread messages and no sound. Then I figured it out that when ever I open EasyBoost - Skype starts to glitch again. Now I use EVGA Precission X. Now after a month, I cleaned computer and closed the case, it was open all the time. I started to overclock GPU clock only (just a bit) because there was no problems that would stop me. So sometimes on heavy CPU load graphics starts to lag. Dragging a window is painful to watch too. Sometimes the screen freezes for 5 to 10 seconds (I can see that hard disk activity is maximal). You may say that CPU fault it is, isn't it? But sometimes lag spikes starts randomly when CPU load is at maximum. All 3 benchmark softwares (PerformanceTest, NovaBench and MSI Kombustor) shows that performance of my video card has dropped about 25%. BUT! CPU score is lower too. I ignored these problems but when I refreshed Windows Experience Index I was shocked. Month before (in latvian language but not so hard to understand): Now (upgraded RAM): This happened when I tried to capture Minecraft with Fraps on underclocked GPU to 580mhz (def: 590mhz): All drivers are up to date. Average CPU temperature from 55°C to 75°C (at 70°C sometimes starts these lag spikes). Video card's tempratures are from 45°C to 60°C (very hard to reach 60°C). So my hope is that the video card is fine, cause this card is very new and I want to upgrade CPU anyways. Aplogies for my mistakes in vocabulary (I am trying to type this as fast I can).

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  EDIT: I thought I pinpointed the problem. Just now I tried to go to the firefox addons page which uses https and gmail also uses https. So I thought I am unable to load https pages on this computer. So I went to a bank site which uses https but that loads just fine. Sigh.... I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter EDIT: I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Why do some games randomly turn my screen a random solid color?

  - by Emlena.PhD

  When playing some games my computer will randomly have an error that I cannot fix without turning it off and back on again. The screen changes to one solid color, which varies (off the top of my head I can remember seeing solid green, magenta, etc..) and the sound blares a single tone. The sound sometimes briefly restores and I can still hear the game sounds and even hear and still be heard by people in my Mumble channel, but the screen doesn't right itself so I'm still blind. What's more is this happens in some games but not in others. While the game is actually running, not while I'm still in the menu. However, it does happen if I'm afk or idle but the game world is still rendering. Games where the error occurs: League of Legends World of Warcraft Trine The Sims 2 Dungeon Defenders Safe games: games where it has never occurred: Tribes: Ascend Star Wars: the Old Republic Battlefield 3 So relatively older games cause the problem while newer games do not? I cannot predict when it will happen, it just seems random. However, if it happens and I try playing the same game further after restart it does appear to occur more frequently after the first time. But if I switch to a safe game it doesn't continue happening. Both of my RAM sticks appear fine, flipped position or either one on their own and games still run, computer still boots. I would think over-heating, but then why not all games? ALso, sometimes it happens immediately after I start playing, within seconds of the 3D world booting up. I'm looking to upgrade very soon so I want to figure out what component or software is fubar and replace/repair it. Any suggestions or recommendations of tools would be helpful. Below is some system information. Dxdiag does not detect any problems. Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120305-1505) System Manufacturer: Gigabyte Technology Co., Ltd. System Model: EP45-UD3R BIOS: Award Modular BIOS v6.00PG Processor: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (2 CPUs), ~3.2GHz Memory: 4096MB RAM DirectX Version: DirectX 11 DxDiag Version: 6.01.7601.17514 64bit Unicode Graphics card name: NVIDIA GeForce GTX 285 Driver Version: 8.17.12.9610 (error has occurred w/several driver versions) Sound: I do not have a sound card, been using motherboard's built in sound)

  Read the article

• Simple mdadm RAID 1 not activating spare

  - by Nick Liu

  I had created two 2TB HDD partitions (/dev/sdb1 and /dev/sdc1) in a RAID 1 array called /dev/md0 using mdadm on Ubuntu 12.04 LTS Precise Pangolin. The command sudo mdadm --detail /dev/md0 used to indicate both drives as active sync. Then, for testing, I failed /dev/sdb1, removed it, then added it again with the command sudo mdadm /dev/md0 --add /dev/sdb1 watch cat /proc/mdstat showed a progress bar of the array rebuilding, but I wouldn't spend hours watching it, so I assumed that the software knew what it was doing. After the progress bar was no longer showing, cat /proc/mdstat displays: md0 : active raid1 sdb1[2](S) sdc1[1] 1953511288 blocks super 1.2 [2/1] [U_] And sudo mdadm --detail /dev/md0 shows: /dev/md0: Version : 1.2 Creation Time : Sun May 27 11:26:05 2012 Raid Level : raid1 Array Size : 1953511288 (1863.01 GiB 2000.40 GB) Used Dev Size : 1953511288 (1863.01 GiB 2000.40 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Mon May 28 11:16:49 2012 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Name : Deltique:0 (local to host Deltique) UUID : 49733c26:dd5f67b5:13741fb7:c568bd04 Events : 32365 Number Major Minor RaidDevice State 1 8 33 0 active sync /dev/sdc1 1 0 0 1 removed 2 8 17 - spare /dev/sdb1 I've been told that mdadm automatically replaces removed drives with spares, but /dev/sdb1 isn't being moved into the expected position, RaidDevice 1. UPDATE (30 May 2012): A badblocks destructive read-write test of the entire /dev/sdb yielded no errors as expected; both HDDs are new. As of the latest edit, I assembled the array with this command: sudo mdadm --assemble --force --no-degraded /dev/md0 /dev/sdb1 /dev/sdc1 The output was: mdadm: /dev/md0 has been started with 1 drive (out of 2) and 1 rebuilding. Rebuilding looks like it's progressing normally: md0 : active raid1 sdc1[1] sdb1[2] 1953511288 blocks super 1.2 [2/1] [U_] [>....................] recovery = 0.6% (13261504/1953511288) finish=2299.7min speed=14060K/sec unused devices: <none> I'm now waiting on this rebuild, but I'm expecting /dev/sdb1 to become a spare just like the five or six times that I've tried rebuilding before. UPDATE (31 May 2012): Yeah, it's still a spare. Ugh! UPDATE (01 June 2012): I'm trying Adrian Kelly's suggested command: sudo mdadm --assemble --update=resync /dev/md0 /dev/sdb1 /dev/sdc1 Waiting on the rebuild now... My questions are: Why isn't the spare drive becoming active sync? How can I make the spare drive become active?

  Read the article

• Operative systems on SD cards

  - by HisDudeness

  I was getting some wild ideas the last days, like putting some operative systems into SD cards rather than on my hard drive. I'll go further into details now and explain what lead me to consider this probably abominable decision. I am on a laptop (that means I have a native SD-card reader) which is currently running a cross-distro setup, with a bunch of Linux systems (placed in dedicated ext4 logical partitions into a huge extended one) regulated by an unique GRUB. Since today, my laptop haven't even seen any Windows system with binoculars. I was thinking about placing all the os part of my setup into a Secure Digital to save all my 500 Gb Hard Drive for documents, music, videos and so on, and being able to just remove the SD and boot my system into another computer too, as well as having the possibility of booting other systems into mine by just plugging in another SD, without having to keep it constantly placed in my PC. Also, in the remote case in the near future I just wanted to boot Windows 8 in it, I read it causes major boot incompatibility issues with other systems by needing a digital signature in order for them to start. By having it in a removable drive, I could just get rid of it when I'm needing him and switch its card with Linux one, and so not having any obstacles to their boot. Now, my questions are: I know unlikely traditional rotating disk drives, integrated circuits ones have a limited lifespan in terms of cluster rewriting. Is it an obstacle to that kind of usage? I mean, some Ultrabooks are using SSD now, is it the same issue, or there are some differences between Solid State Drives and Secure Digitals in that sense? Maybe having them to store system files which are in fixed positions (making the even-usage of cluster technology useless) constantly being re-read and updated and similar things just gets them soon unserviceable, do it? Second question: are all motherboards and BIOSes able to boot from SDs just like they are from USB pen drives (I mean, provided card reader is USB-connected, isn't it)? Or can't bootloaders like GRUB be installed on SDs working? If they can't, is it a solution installing GRUB to MBR and making boot option pointing to SD? Will it work? Are there any other problems to installing OSs on a Secure Digital?

  Read the article

• Cannot install grub to RAID1 (md0)

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

  Read the article

• Unextending Sharepoint 2007 Web Application from a zone

  - by dunxd

  When our Sharepoint was migrated from Sharepoint 2003 to Sharepoint 2007 (both fully paid versions), the consultants who carried it out extended each web app into two IIS sites/zones (e.g. the original Web App was http://intranet, then http://newintranet and http://intranet would be created for Sharepoint 2007 - each with its own IIS site). The idea was that during the migration period we would set up DNS to point the old url to SP2003 servers and the new one to SP2007, then once the migration was complete, do a DNS change so the SP2007 would recieve the requests to the http://intranet type URLs. Unfortunately the contractors did not tidy up the application extensions and IIS sites after the migration, and for some time both URLs were in use, resulting in many document links pointing to the http://newintranet type URLs. This means I need to maintain these URLs. Due to a rejig of organisation structure we now need to relocate some Sharepoint sites, and I'd like to use the RDA Collaboration Sharepoint URL Redirector feature. However a limitation of this is that it doesn't work for Web Applications which have been extended into multiple zones. So I have a need to tidy up the situation that our consultants left behind. I think the right thing to do is use the "Remove Sharepoint from IIS Web Site" page in Central Admin to remove the zone for the newintranet type sites, and select the option to also delete the IIS site. That should result in having no IIS sites listening for http://newintranet type URLs. Is this the right procedure? Once I have done that I need to set up Sharepoint to receive requests sent to the http://newintranet type URLs so they will continue to work. I am not sure if I should do this: using Alternative Access Mappings or, by adding a host header to the IIS site or, creating a non Sharepoint IIS site for each http://newintranet type URL, and use IIS redirection to forward the requests to the new URL using variables to pass the path to the Sharepoint site. Does anyone have any thoughts on these options, or any other way of achieving this? Sharepoint 2007 is running on Windows 2003 with IIS6. We don't currently have plans/budget to upgrade to Sharepoint 2010.

  Read the article

• Assign fixed IP address via DHCP by DNS lookup

  - by Janoszen

  Preface I'm building a virtualization environment with Ubuntu 14.04 and LXC. I don't want to write my own template since the upgrade from 12.04 to 14.04 has shown that backwards compatibility is not guaranteed. Therefore I'm deploying my virtual machines via lxc-create, using the default Ubuntu template. The DNS for the servers is provided by Amazon Route 53, so no local DNS server is needed. I also use Puppet to configure my servers, so I want to keep the manual effort on the deployment minimal. Now, the default Ubuntu template assigns IP addresses via DHCP. Therefore, I need a local DHCP server to assign IP addresses to the nodes, so I can SSH into them and get Puppet running. Since Puppet requires a proper DNS setup, assigning temporary IP addresses is not an option, the client needs to get the right hostname and IP address from the start. Question What DHCP server do I use and how do I get it to assign the IP address based only on the host-name DHCP option by performing a DNS lookup on that very host name? What I've tried I tried to make it work using the ISC DHCP server, however, the manual clearly states: Please be aware that only the dhcp-client-identifier option and the hardware address can be used to match a host declaration, or the host-identifier option parameter for DHCPv6 servers. For example, it is not possible to match a host declaration to a host-name option. This is because the host-name option cannot be guaranteed to be unique for any given client, whereas both the hardware address and dhcp-client-identifier option are at least theoretically guaranteed to be unique to a given client. I also tried to create a class that matches the hostname like this: class "my-client-name" { match if option host-name = "my-client-name"; fixed-address my-client-name.my-domain.com; } Unfortunately the fixed-address option is not allowed in class statements. I can replace it with a 1-size pool, which works as expected: subnet 10.103.0.0 netmask 255.255.0.0 { option routers 10.103.1.1; class "my-client-name" { match if option host-name = "my-client-name"; } pool { allow members of "my-client-name"; range 10.103.1.2 10.103.1.2; } } However, this would require me to administer the IP addresses in two places (Amazon Route53 and the DHCP server), which I would prefer not to do. About security Since this is only used in the bootstrapping phase on an internal network and is then replaced by a static network configuration by Puppet, this shouldn't be an issue from a security standpoint. I am, however, aware that the virtual machine bootstraps with "ubuntu:ubuntu" credentials, which I intend to fix once this is running.

  Read the article

• debian packages version convention

  - by JackWu

  I'm using debian/Ubuntu, and get confused about versions of packages. When using dpkg -l command, I get: ii vim 2:7.3.429-2ubuntu2.1 Vi IMproved - enhanced vi editor ii vim-common 2:7.3.429-2ubuntu2.1 Vi IMproved - Common files ii vim-runtime 2:7.3.429-2ubuntu2.1 Vi IMproved - Runtime files ii vim-tiny 2:7.3.429-2ubuntu2.1 Vi IMproved - enhanced vi editor - compact version ii virt-what 1.11-1 detect if we are running in a virtual machine ii w3m 0.5.3-5ubuntu1 WWW browsable pager with excellent tables/frames support ii watershed 6 reduce superfluous executions of idempotent command ii wget 1.13.4-2ubuntu1 retrieves files from the web ii whiptail 0.52.11-2ubuntu10 Displays user-friendly dialog boxes from shell scripts ii whoopsie 0.1.33 Ubuntu crash database submission daemon ii wimlib9 1.5.0-1~webupd8~precise Library to extract, create, modify, and mount WIM files ii wimtools 1.5.0-1~webupd8~precise Tools to extract, create, modify, and mount WIM files ii wireless-tools 30~pre9-5ubuntu2 Tools for manipulating Linux Wireless Extensions ii wpasupplicant 0.7.3-6ubuntu2.1 client support for WPA and WPA2 (IEEE 802.11i) ii x11-common 1:7.6+12ubuntu2 X Window System (X.Org) infrastructure ii x11-utils 7.6+4ubuntu0.1 X11 utilities ii xauth 1:1.0.6-1 X authentication utility ii xbitmaps 1.1.1-1 Base X bitmaps ii xclip 0.12-1 command line interface to X selections ii xfonts-encodings 1:1.0.4-1ubuntu1 Encodings for X.Org fonts ii xfonts-utils 1:7.6+1 X Window System font utility programs ii xkb-data 2.5-1ubuntu1.3 X Keyboard Extension (XKB) configuration data ii xml-core 0.13 XML infrastructure and XML catalog file support rc xpdf 3.02-21build1 Portable Document Format (PDF) reader ii xterm 271-1ubuntu2.1 X terminal emulator ii xz-lzma 5.1.1alpha+20110809-3 XZ-format compression utilities - compatibility commands ii xz-utils 5.1.1alpha+20110809-3 XZ-format compression utilities ii zabbix-agent 1:1.8.11-1 network monitoring solution - agent ii zlib1g 1:1.2.3.4.dfsg-3ubuntu4 compression library - runtime ii zlib1g-dev 1:1.2.3.4.dfsg-3ubuntu4 compression library - development ii zsh 4.3.17-1ubuntu1 shell with lots of features The third column is version, but it all messed up in a way I can't understand. I mean, different packages use total different naming specification. Here are the major questions: Why there are ubuntu in them, and there are not? what all the special -~+ mean? alpha and build, dfsg, what are they? Can I just use them casually? vim and other packages have 2:, what does that mean? How version comparison works, since they can be so different? Can anyone please explain this to me? Or where can I find an official document? Thanks in advance.

  Read the article

< Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >