Search Results

Search found 8782 results on 352 pages for 'krishnadas pc'.

Page 315/352 | < Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >

• How do I connect to and factory reset a Catalyst 3560 Switch?

  - by Josh

  My company just bought another company. In their server room they had some older hardware, which I would like to repurpose. One of these is a Cisco Switch: C3560G-48TS-S. I found some instructions about this switch here but this is not a guide for a beginner. I have no idea how to connect to this thing to begin running the commands. It says Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. But I can't find anything on how to do this (assuming with telnet?) or even what program to use. I also don't know how to find the IP address of the device to connect to it. My research also says once I get in there, I need to run clear config all Is this the right command? Also, what if I can't get the username and password for these devices? Is there some way to factory reset (my only experience is with devices that have a hardware reset button) EDIT: I should note that when I push the button on the front the three lights blink, which according to the documentation indicated the switch is configured and "not available for express setup"

  Read the article

• Drive letter not appearing after heat-related crash

  - by NickAldwin

  I recently had my old PC (has 3 physical hard drives partitioned into 6 partitions) off while on vacation. When I came back, I turned it on. I hadn't realized the room was warmer than it usually is due to hot weather while I was away. The computer was extremely slow to start up, then it crashed. When i rebooted, it got halfway through chkdsk on one of the non-system partitions, then crashed again. I opened it up and felt the hard drives and immediately shut down the computer and moved it to my basement to cool down because it was so hot. I left it there for a length of time while I reinstalled the A/C. I have now turned it on again. It is working fine, and every drive except for the one with the partition that was being checked has appeared in Windows. I scheduled chkdsk for all of the other partitions anyway, just in case, but I'm worried about that drive. I'm pretty sure the drive itself hasn't broken but that crashing in the middle of a chkdsk repair may have corrupted the data. What would you do in this situation? Most of the data on that drive was backed up, so it's not a huge deal if I lost it, but I'd like to get it back if I could. I also would love to regain usability of the drive, even if I have to wipe it -- but that's a last-resort sort of thing. What do you suggest I do?

  Read the article

• Concurrent users with Quickbooks?

  - by airietis

  I work in a company with 3 people who regularly use the same Quickbooks file. However, they work remotely on different networks. I need to implement a solution that allows all three of us to access Quickbooks at the same time remotely (and each make changes at the same time). We have a spare desktop PC that can be utilized as a server. So, my question is: what is the cheapest and most hassle-free solution to solving this problem? I've considered using application cloud hosting, however, it is very expensive ($40 per user a month) and we are on a tight budget. Is it possible to install Quickbooks on my own server, and have them connect to it remotely? If so, what is the best way to accomplish this? Remote desktop protocol? Or is there a built in feature for this with Quickbooks Premier 2013? EDIT: As MDMarra mentioned, I am looking for a solution that offers true simultaneous access. Will using a dedicated server and having users connect to a VPN be a viable solution?

  Read the article

• Is there an Installer Analyser tool that can list what Registry Keys will be created?

  - by EvoGamer

  I can think of 3 ways to achieve my goal: Create a clean VPC, install a given piece of software, and compare the before and after states. Somehow reverse-engineer the installer. Somehow redirect the output of the installer in question so that all registry calls and copy/move file commands are recorded, but not executed. The first option can be done manually, or potentially automated, but I feel it's rather OTT for my needs. The second could cause all sorts of licencing issues, not to mention it may not always return a correct result. Also, without delving into hex editing, I can't think of a way that it would be possible to do manually (some installers - eg Anti-Virus software - may react unfavourably on automated attempts to investigate the installer). The third option shows the most promise, although if the first could be stripped down into a lightweight throwaway environment, it would work pretty much the same way. However, I'm not sure how to do it. So my question is: What tools are available (if any) and/or how could I find out this information manually? I'm not looking to reverse-engineer anything (if I can help it), but I just want to know exactly what changes are being made to my PC by a given piece of software.

  Read the article

• How to Monitor Network in Medium-Sized Company?

  - by Kyle Lowry

  I work at a medium sized company (100+ employees). An issue that has been cropping up is network performance, internet access in particular. We have about 70 or more computers, a mix of Mac OS X and Windows XP & 7 machines. We have several servers (Exchange server, PC file servers, MS SQL, Blackberry, FTP, Mac server, etc). There are four main switches, a SonicWall firewall, and probably a couple routers in the server room with a dozen or so more scattered around the building. The network structure has grown organically over a number of years; and, as far as I know, there really isn't a monitoring solution in place. When we experience network issues (slow connections, dropped packets, and so on), our general solution is to power cycle some hardware or go around to each employee and ask them if they are uploading/downloading any large files. This is really inefficient and time consuming, and it does not allow us to monitor the network, tackling potential problems proactively. I would like to find a solution that would allow me to monitor network usage company-wide in real time, with detail going down to the individual computer, ideally. Given the hodgepodge of equipment and operating systems, what would be the best way to set up some kind of monitoring solution? Hardware, software, restructuring our network architecture?

  Read the article

• Windows 8 not shutting down properly

  - by Patrick

  Since installing Windows 8, the computer hasn't been shutting down properly. When selecting to power down, the PC quickly displays the shutting down screen, the monitor powers off, and the computer remains on but unresponsive. After about 5 minutes, the computer will turn off. Upon booting into windows again, I am informed that Windows didn't properly shut down. I'm running a fast SSD, and it's a clean install of Windows 8, so there's no way Windows is taking that time to do some sort of hibernate on shutdown or whatever - not to mention the error when entering Windows the next time. This happens on every shut down. Restart works as expected. EDIT: Formatting again didn't work. Fails regardless of drivers installed. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.

  Read the article

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• Last step in HDD Recovery (fixing windows)

  - by Atom Computing

  My dad’s hard drive corrupted which was a result of many bad sectors. Anyway, I made a clone of the drive and have now repaired it totally (recreating the MBR and MFT) and doing a series of ChkDsk's on it. I can now see all the files and folder on it and it is all intact. I currently have it as a slave in my computer (where I was doing all the repairs). When putting it back into the computer, it comes up with "A disk read error occurred: Press Ctrl + Alt + Del to Restart". I don’t know why this is happening but think it might have something to do with file permissions. I have tried a start-up recovery on the Vista boot CD and it found no problems. When trying to apply file permissions (and creating file perms for the SYSTEM group (as it didn’t have any for SYSTEM group)) it couldn't apply them for some of the System32 folder files. I have tried applying them as admin and with as powerful privileges I can get. All to no avail. When it is in my PC I can boot it up (I added it into my bootloader) and it boots up fine except when it logs in it comes up with the error - "Rundll32.exe - Windows cannot access the specified device, path or file. You may not have the appropriate permissions to access the item" This message keeps coming back and nothing loads at all. Any help would be greatly received as I have got so far with the data recovery and want to avoid a reformat at all costs due to the vast number of programs installed and I don’t have much time on my hands! Thanks

  Read the article

• crontab not running on VirtualBox unless I'm logged in

  - by Mike

  I am running Ubuntu Server 9.04 in VirtualBox on my work PC as a development environment. I have some scripts that I've put in my user's crontab that run throughout the day while I'm SSHed into the VM. Last night, I closed PuTTy and all of my other running applications (except for VirtualBox and the VM) and went home. I came back this morning to discover that my cron jobs didn't run at all, yet when I SSHed into the VM, the next scheduled job ran. I set the schedule to 5min to test, disconnected again, and the jobs stopped running on schedule. They seem to only run if I'm logged in to the machine. Obviously, I want them to run on schedule even if I'm not logged in to the VM, otherwise there's no point. Is there something I've failed to configure correctly? New Information: There are now 3 entries in /var/log/cron.log saying the following "Mount of private directory return code [256]"... the entries correspond to when the cron job is supposed to run. I thought they are supposed to run as my userid? Why would my own userid be unable to run a script in my home directory?

  Read the article

• Microphone array support in Windows. Info on performance and compatible hardware?

  - by exinocactus

  It is officially claimed by Microsoft (Audio Device Technologies for Windows), that Windows Vista has an integrated system-level support of microphone arrays for improved sound capturing by isolating a sound source in target direction and rejecting ambient noise and reverberation. In more technical terms, an implementation of an adaptive beamformer. Theoretically, microphone arrays with 2-4 mics can substantially improve SNR under some conditions like speaker in front of the laptop in noisy environment (airport, cafe). Surprisingly, though, I find very little information about commercially-available products supporting these new features. I mean products like portable usb micropone arrays or laptops or flat screens with integrated mic arrays. I could only find info about two laptop models having "noise cancelling digital array microphone". These are Dell Latitude and Eee PC 1008P-KR. Now my questions: Do you have any experience with the Windows beamformer implementation? For instance, in the above mentioned laptops. How well does it work? Are there any tests results available in the net or in print (papers?)? Do you know about other microphone array hardware? What could be the reason why mic array technology didn't get sucess Is there mic arrays support in 'Windows 7'?

  Read the article

• SSO to multiple websites from Sharepoint website

  - by Aico

  We have an intranet based on Sharepoint 2010. In this intranet we have several links to other webservers within the same Active Directory, for example a link to our Outlook Web Access site on our Exchange 2010 environment. We have three different setups which visit this Sharepoint environment and the other webservers: Windows 7 clients that are a member of the Active Directory Home pc's that connect through a SSL VPN appliance Standalone thin clients (Windows 7 embedded) within the corporate network The goal is to let people only sign in once. In the first group this isn't a problem because the AD Integrated Authentication works fine and the Windows logon is passed on to Sharepoint and the other webservers. The second group is also working fine because of the LDAP integration that the SSL VPN appliance uses. The third group is however experiencing issues. They need to enter their credentials everytime they click a link to another webserver. They first need to enter credentials for accessing the Sharepoint environment. When clicking the link for their webmail they have to re-enter their credentials, and so on. Can someone tell me what the best solution would be to also get SSO working fine for the third group? Some extra information: We also have a Forefront TMG server in our environment. I read somewhere that Forefront might be part of a solution for this problem, but not sure how. Maybe someone here can help me? Look forward to some help. Best regards, Aico

  Read the article

• How to avoid en.voyages-sncf.com redirecting to uk.voyages-sncf.com?

  - by Mark Smith

  OK, so en.voyages-sncf.com is French Railways' English language website with full functionality for train booking in France - it sells iDTGV, offers seating options etc. uk.voyages-sncf.com is their UK subsidiary, with reduced functionality, no seat options, no iDTGV etc. Previously, I have been able to select 'Other countries (EUR)' top right and go from the uk version to the en version, or just type in the direct url 'en.voyages-sncf.com and go there. Now, they seem to have implemented an automatic redirect so whenever I enter 'en.voyages-sncf.com' on my UK-based PC or indeed try to select 'Other countries (EUR)' it automatically bumps me to uk.voyages-sncf.com, which I don't want. I can't get onto en.voyages-sncf at all. So, short of using a heavyweight solution like using a non-UK proxy server or downloading the TOR browser, is there any simple solution? Like telling my browser to go to en.voyages-sncf, go directly to en.voyages-sncf and no other site, do not pass go, do not collect £200, do not go anywhere else, ignore all redirects and do what you're told by ME, not by those Machiavellian so-and-sos?

  Read the article

• Force Installing a Radeon HD 2100 on Windows 8

  - by Click Ok

  I'm trying force installing a Radeon HD 2100 on Windows 8. I've found that link from AMD with the drivers for Windows7: http://support.amd.com/us/gpudownload/windows/legacy/Pages/legacy-radeonaiw-vista64.aspx I know too that AMD will stop support Radeon HD 400 and older: http://www.techspot.com/news/48321-amd-drops-windows-8-support-for-radeon-hd-4000-and-older.html Now, let's go to the problem. If I try install the 12.6 driver, Windows will stick with the "basic display adapter", and this is bad for 3d games like Minecraft, that runs really slow now compared with the previous Windows7 installation. Forcing install the catalyst driver can help to fix it. So, I follow that steps: Extract the Catalist Driver (C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql) Right click the "basic display adapter" on device manager, and "update driver" Search on PC I will choose the driver "With Disk" "C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql\Packages\Drivers\Display\W76A_INF" There is a big list of drivers and the nearest driver to HD 2100 is "Radeon HD 2350 Series" My questions: Why isn't "Radeon HD 2100 Series" listed? (or Where is it listed?) In theory it must be listed" The first link above show that "This article applies to the following configuration(s):" (...) "AMD Radeon HD 2000 Series" Am I doing something wrong?

  Read the article

• How to automatically start VM created by virt-manager?

  - by Jeff Shattock

  I have created a virtual machine with virt-manager that runs on kvm/qemu. The machine works well when started through virt-manager. However, I would like to be able to start and stop the VM through a script in init.d, so that it comes up and down along with the host. I need to have virt-manager show that the machine is running, and to be able to connect to its console through there. When I use the command line that is produced by running ps -eaf | grep kvm after starting the vm through virt-manager, I get some console messages about redirected character devices, but the machine does start and runs properly. However, I do not get any indication from virt-manager that it has started. How can I modify the command line to get virt-manager to pick up the running VM? Is there anything else about the command line that should change when starting outside of virt-manager? Command line is (slightly reformatted for readability): /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1 -name BORON \ -uuid fa7e5fbd-7d8e-43c4-ebd9-1504a4383eb1 \ -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/BORON.monitor,server,nowait \ -monitor chardev:monitor -localtime -boot c \ -drive file=/dev/FS1/BORON,if=ide,index=0,boot=on,format=raw \ -net nic,macaddr=52:54:00:20:0b:fd,vlan=0,name=nic.0 \ -net tap,fd=41,vlan=0,name=tap.0 -chardev pty,id=serial0 -serial chardev:serial0 \ -parallel none -usb -usbdevice tablet -vnc 127.0.0.1:1 -k en-us -vga cirrus

  Read the article

• Dedicated Mouse and Keyboard on Virtual Box VM

  - by Myersguy

  To all super users, Currently I am trying to run virtual box on my second monitor, with a dedicated mouse and keyboard. However, doing so has not proven easy. There has been times where the mouse works, but not the keyboard, vice versa, or nothing works at all. The biggest problem I am running into is this: When enabling the USB mouse and keyboard from the VM, I get an error: 'USB Device is busy with a previous request.' The only thing that is using second mouse and keyboard, however, is Windows. The other error I have received stated that the VM was unable to create a proxy for the device. Additionally, the VM occasionally will disable the secondary keyboard entirely, requiring me to unplug and replug it into my PC to re-enable it again. Keyboard auto-capture is disabled, and while a solution I was reading online stated to turn off mouse integration, that option is grayed out on my machine. Any help would be appreciated. Thanks. /firstquestion.

  Read the article

• Grub Installation Failed: Fatal Error ... now what I do?

  - by eklavya

  I know there are some threads that touch this but I feel I have done something uniquely stupid. hence the post and plea for help. I am a beginner @ Linux. So I have a PC with a HDD (hard disk drive) and SSD (solid state drive) It was running Linux Mint /dev/sda1 - HDD Partition 1 - 2 TB (mounted this is /home /dev/sda2 - HDD Partition 2 - 1 TB (separate back up drive, i was backing up files to this) /dev/sdb1 - SSD Partition 1 - 100 GB (OS) /dev/sdb2 - SSD Partition 2 - 20 GB (Swap) The operating system was Linux Mint and was installed on the /dev/sdb1 i.e the solid state drive. I had partitioned off the sda into 2 TB and 1TB and presented the 2 TB as the /home to the OS. Anyway last night I decided to make a return to Ubuntu via the path of Elementary OS. Everything went fine with the install until it stated that GRUB installed failed and this was a Fatal error (no kidding I said). No I am stuck. I have definitely done something wrong and don't know what it is... My biggest pain is the files on the /dev/sda2. I want to save these before I try something drastic like wiping off the /dev/sda completely. So I have the following questions... Can I use a liveCD USB to save these files ? I can see the /dev/sda2 but was unable to access the files in the liveCD last not least ... how do I fix the main issue here. Why could the OS not install GRUB 2b... why is my SSD the /dev/sdb ... and not /dev/sda. Does that have something to do with it that my master boot record sits on the HDD /dev/sda and not /dev/sdb

  Read the article

• Hard drive causing BSOD

  - by JoshIrving

  I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

  Read the article

• JavaScript settings are on but I still have issues with web sites using JavaScript.

  - by Mike

  I have two computers that are the same at home except I have installed Adobe Acrobat 9 Pro Extended on my main computer along with the 2010 Outlook (Beta). I have issues when I log into a website that uses pop up calendars to select the date. I pasted it below. I checked my other computer and it is fine. I've checked the Java setting and they are correct. I am at a loss. Any suggestions? Webpage error details User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; HPDTDF; OfficeLiveConnector.1.4; OfficeLivePatch.1.3; eMusic DLM/4; .NET4.0C) Timestamp: Mon, 26 Jul 2010 22:03:59 UTC Message: 'CalendarPopup' is undefined Line: 390 Char: 2 Code: 0 Message: 'CalendarPopup' is undefined Line: 410 Char: 2 Code: 0

  Read the article

• Windows 7, Black screen with cursor, impossible to logon

  - by PJC

  First - I have gone through as many possible solutions I've found here and elsewhere. [Edit - to describe the issue in more detail, the PC appears to boot correctly, but instead of the logon screen, I have been getting a black screen WITH the pointer cursor, and it responds correctly to the mouse. Pressing CTL-ALT-DEL brings up the logon screen's background, but with no logon area nor any other content. This screen was at the full resolution before I uninstalled the graphics driver in safe-mode.] I also just ran a full up-to-date AVG scan from boot media. [Edit - the AVG scan, which was updated to today's virus signatures, found no issues at all.] So - steps I've tried: Safe Boot, Restore from before the issue - done, no help. Uninstall the graphics driver - done, now i have a 1024x768 fallback screen, still no way in. sfc /scannow - only doable from Safe boot obviously, but no change. [Edit - booting from restore media, performing a startup repair and...]Restore further back - restored to 2 days ago, and I'd had many reboots since then with no problem. Enable autologin to try to get beyond the login screen - done, doesn't work. It seems the best advice is complete reinstall, but I really don't want to do that because it'll take 3-4 days to add all the apps I use. Some key points to note - in both states - before and after removing the video driver, I always had a mouse cursor on the screen. CTL-ALT-DEL flashes up the login background, but no login info. I can (and often do) reinstall from scratch, but was at a fairly stable state before this, and would prefer not to. -Paul

  Read the article

• VPN with VLANs? [closed]

  - by Craig

  As usual, I'm sure I'm in way over my head on this one. My networking skills are limited; so, bear with me if you will. What I have are a few testing servers at my house as well as at a friends house that I want to link together so they can see each other (VPN right? I've done those before). We want to be able to see all the servers and work with them from either location. All the servers also need to be able to see each other. But, we don't want to see each others PCs, printers, PS3s etc. How do we pull that trick off? Multiple VLAN?... subnets?... what? If hardware matters, I have an old PC I was planning on loading pfSense onto because my current el-cheapo router doesn't support VPN. The VPN linking the houses is about the only thing I'm sure on. Beyond that, I'm lost. I'm not a complete noob; but, like I said, I'm not so sharp with the more complex networking. I do however read well... So use lots of descriptive words and feel free to link away to long dry articles if necessary. :-)

  Read the article

• Graphics artifacts/distortion with Win7 and nVidia

  - by Gepard

  Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

  Read the article

• Windows Server 2003 (w/Exchange) move to new machine

  - by James Booker

  I have an ageing domain controller (the only one on a 10-pc network) which needs rebooting often. I have a Dell Poweredge 2850 server doing nothing, so I'd like to move the DC to that, but here's the catch - I don't have Win2k Server Std install media any more as it's been lost. I purchased "Easus Todo Backup Advanced Server" which claims to be able to recover to dissimilar metal, but it's not quite working (although I don't think it's the product's fault) I know the server and PERC RAID card are good because I installed Ubuntu on the logical drive (4 x 72GB disks RAID 5) no problems. I've booted frmo the Easus Todo backup CD (which is WinPE based) and recovered to the logical disk on the RAID (after installing driver inside the WinPE environment from a NAS drive) The problem is when I boot the server, I can get the OS selection menu, but any option results in a blank screen, with no errors. I figure this is probably because the driver wasn't installed on the old machine (which is IDE-based (i know, i know!) and doesn;t have a RAID controller) I've booted from the CD and copied the mraid35x.sys file to the c:\windows\system32\drivers folder on the recovered system, but it makes no difference. I made a boot.ini with rdisks 0-10 defined, and booting from each of these resulted in a file error (i.e. 'this isn't a real disk') - the only disk that gets any response (the blank screen) is multi(0)disk(0)rdisk(0)partition(1) which just gives me the blank black screen and no disk activity. Is there any way I can force the drvier to be installed on the source system (so i can do a full backup again), i've tried right-clicking the oemsetup.inf and clicking install, but it didn't actually do anything. I attempted to force it with the 'Add new hardware' wizard and forcing with the 'have disk' option but it still gave me no hardware to select. Also I've got an identical machine running WinXP which uses the PERC driver successfully (which was obviously done at install time) and the boot.ini settings are the same : multi(0)disk(0)rdisk(0)partition(1) Any ideas would be appreciated.

  Read the article

• Remote Desktop leaves host unresponsive

  - by Jeff Dalley

  I have my desktop PC at home set up to accept remote connections, and I often connect to it from work on my laptop via mstsc.exe. However, every time I remote to it, I find when I go home that despite the monitor being on - it's not receiving an image and it looks as though the computer is hibernating/asleep. I basically have to restart it whenever I get home and I know there's an answer for why its doing this. More details: When exiting the remote session, I have tried both logging off the account, and closing the RDP window without logging off; both give the same result. When I get home to the desktop I of course try moving the mouse, ctrl+alt+del to see if its responsive to restart, multiple key-press to see if I can get any audio out of it; It seems pretty obvious its sleeping/hibernating in some way: Nothing happens in any of these cases and a physical restart is necessary. Both desktop and laptop are running Windows 7 Ultimate. I'm thinking it really is sleeping/hibernating it, and I'm not sure why because left alone my desktop's power options are set to never turn off the HDD or change its state - I leave it on 24/7. This could be a stupid error on my part but I just can't see it! Thanks.

  Read the article

• Data loss by randomly unplugging the computer during runtime

  - by Kan

  I'm from Austria and we and the Germans have some sort of bad science-show which runs every day. What I call it would rougly translate to "half-knowledge" if you want so. By the way: It is called "Galileo". So they thought they'd make a computer myth busters video right now, and I couldn't believe what I saw and heard... The strangest thing to me was that they asked: "Does unplugging the computer damage your data?" Then they started up some machine with Vista on it, started copying some files and randomly unplugged the PC cable, the whole thing around 50 times. After their computer continued to start up normally, they just said "nothing can happen, your data or computer can't be damaged". They of course excluded unsaved data in running programs like text editors from this. I asked myself: What the hell are their "computer experts" saying? You can't tell by unplugging the cable 50 times if that can damage your computer. Can unplugging the cable during runtime cause data loss (as said by the moderator of the show)? (I destroyed my windows registry once during a reset)

  Read the article

• Upgrade or replace?

  - by Felix

  My current PC is about four years old, although I have made upgrades to it throughout its existence. The current specs are: (old) Intel Pentium D 2.80Ghz (32K L1 / 2M L2), Gigabyte 945GCMX-S2 motherboard (old) 2.5GB DDR2 (slot0: 512MB @ 533Mhz; slot1: 2GB @ 667Mhz) (new) HIS Radeon HD 4670 - I think this is limited by the motherboard not supporting PCIe 2.0 (?) (old) WD Caviar 160GB - pretty slow (new) WD Caviar Black 640GB (if any more specs are relevant, let me know and I'll add them) Now, on to my question. I've been having performance issues lately, both in video games and in intensive applications. A couple of examples: Android application development (running Eclipse and the Android emulator) is painfully slow (on Linux). I only realized this when, at my new job as an Android dev, both tools are MUCH quicker. (I'm not sure what CPU I have there) The guys at my new job got me NFS Hot Pursuit, in which I barely get like 5-10FPS, even with graphics options turned all the way down My guess is that the bottleneck in my system is my CPU, so I'm thinking of upgrading to a Quad Core i5 + new motherboard + 4GB DDR3 (or more, 'cause I know you'll all jump and say 8GB minimum). Now: Is that a good idea? Is my CPU really a bottleneck, or is the whole system too old and I should replace it? I run Windows 7 on the old, 160GB HDD (which is on IDE, by the way). Could this slow down games as well? Should I get a new drive for Windows if I want to play new games? I know nothing about power supplies. Could that be a problem / will it be a problem if I upgrade to an i5? How come DiRT2 works on full graphics settings (pretty amazing graphics by the way) and NFS Hot Pursuit pulls only 5-10FPS?

  Read the article

< Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >