Search Results

Search found 10161 results on 407 pages for 'dual boot'.

Page 317/407 | < Previous Page | 313 314 315 316 317 318 319 320 321 322 323 324  | Next Page >

  • Delayed startup of network icon (wi-fi)

    - by Michael Dy
    When my Windows 7 Starter netbook boots up and after everything is loaded, it takes about five minutes before the network icon near the clock becomes functional. When there's an available wi-fi signal (which automatically connects to my netbook as preconfigured) after the boot, my netbook seamlessly connects to it even if the network icon cannot be clicked or accessed. (The icon is shown to be loading for about five minutes.) During this time, when I go to Network and Sharing Center, it takes the same time to load. So even while the icon and the Center cannot be accessed, I can surf the Internet. When my netbook was still new, it didn't have this issue. How do I fix this?

    Read the article

  • sudo: must be setuid root

    - by Phuong Nguyen
    Recently, due to some messy stuff with master boot record, I have to re-install my Ubuntu. Before doing that, I back up all folder (exclude root, bin, sbin, tmp, media, mnt) to a NTFS partition. After installation of Ubuntu, I copied back all the folder using a nautilus (running by sudo nautilus). After that, I reboot my computer. And boom, now I cannot run sudo any more, my network services cannot run. When I run sudo from a terminal, I ge "must be setuid root" error. In ubuntu, root account is disabled by default, I don't know why all these files is no longer under ownership of my account. How would I recover back?

    Read the article

  • I don't understand how GDM is starting...

    - by tladuke
    I'm on Karmic. I had no keyboard, so I enabled autologin and some other stuff over ssh to get x2x going. Now I can't find what I did. I'm trying to just start X and XBMC now. I don't need gnome. I disabled gdm: sudo update-rc.d -f gdm remove but it still somehow manages to start on boot. Where can I look around for what I did? If I stop gdm then startx again, it goes straight to XBMC like I want.

    Read the article

  • Linux SW Raid: whole disk or per-partition?

    - by Steve Pomeroy
    I have inherited a machine which has 2 physical disks and uses Linux SW RAID(1). Both disks are partitioned and are are all individual arrays (/dev/md0, /dev/md6, etc.). Those arrays are then mounted (/boot, /home, etc. even /tmp). As RAID is designed to mitigate physical failures, is there any reason why one would use this technique over whole-disk arrays that are then partitioned (perhaps using LVM)? This seems prone to more potential issues, but may have some special properties that I haven't been able to glean. I'm planning on moving this setup to: disks?SWRAID(1)?LVM as I'll be making multiple VMs out of the one machine, but wanted to make sure I knew what I was doing when I got rid of the old setup.

    Read the article

  • Primary domain controller has crashed, secondary does not log in

    - by Hosm
    Hi everybody, I had a primary domain controller on machine A and a secondary one on machine B in my AD domain. Due to some hardware/software problems, I decided to migrate the role of primary domain controller to machine B. Unfortunately, machine A has totally crashed and does not boot. Now I can not even log in to machine B (which itself was a controller in the domain). I need to log into machine B then choose it as the primary controller. I already have synced DNS and AD info. when machine A was alive. Anyone can provide an idea?

    Read the article

  • Symmetrix gatekeepers on Solaris 10

    - by Milner
    I have some Solaris machines that are connected to EMC Symmetrix for SAN storage. Apparently the Symm has a gatekeeper device that is used with the symmetrix CLI. We don't need the CLI, but I have these gatekeeper devices that constantly fill /var/adm/messages and the like with corrupt label errors. Is there anything I can do (short of deleting the devices on machine start) to get rid of them? Or should I just try to get our SAN guy to get the installer for the CLI? These things are getting annoying, and the devfsadmd daemon keeps rediscovering them on boot.

    Read the article

  • debian squeeze: where do the logs for sysv init scripts go? (why won't my init script work)

    - by sbeam
    my actual problem is trying to debug a init script to start Resque. It works fine run as root from the command line, but does nothing on boot. It has some proper insserv headers and I've run updaterc.d to create the symlinks, and checked that they exist. The script is +x. # find /etc/rc*.d -name \*resque\* /etc/rc0.d/K01resque /etc/rc1.d/K01resque /etc/rc2.d/S01resque /etc/rc3.d/S01resque /etc/rc4.d/S01resque /etc/rc5.d/S01resque /etc/rc6.d/K01resque # ls -l /etc/init.d/resque -rwxr-xr-x 1 root root 2093 Oct 24 03:02 /etc/init.d/resque the script can be viewed here if you like. It uses lsb functions to log messages, which essentially echo() to STDOUT I believe. So where does the output go during startup? It's not in /var/log/*log

    Read the article

  • Windows 7 Dell laptop Forgotten password

    - by jtmk
    Hi, A friend has managed to set up their new Windows 7 Home Premium Dell Inspiron and forgot the password they have used. I have tried the following password reset software to no avail: UBCD OHPCrack Offline NT Password & Registry Editor *Trinity Kon Boot I have also tried to do a system restore but this asks for the password. The user does not have any data they need to save. Is there anyway I can get access to the restore partition using Linux to create a recovery disk or do I have to purchase a recovery disk from Dell? Any help is greatly appreciated.

    Read the article

  • Ubuntu: How to login without entering username and password

    - by torbengb
    I'm a newbie running Ubuntu 9.10. I have two users (wife and me), and each user's screensaver is set to lock so that on wakeup, we get to choose which user's desktop to go to. However, Ubuntu requires a password, so this is pretty tedious. I'd like to switch users without entering any password. I know about this trick that works for the boot login, but it doesn't deal with multiple users. Is it possible to set empty passwords for users in Ubuntu, or skip the password in other ways? (I'm expecting real Linux users to suggest that passwordless users must not get any rights and there be an admin user with a strong password. Yes, you're right. But that's not what this question is about. Thanks.)

    Read the article

  • After using lvextend, I can't recover unused space

    - by Cory Gagliardi
    I needed to add more disk space to my CentOS VM, so I added another virtual disk, then used lvextend to add the space to the existing partition. The steps I followed was: echo "- - -" > /sys/class/scsi_host/host0/scan pvcreate /dev/sdb vgextend VolGroup00 /dev/sdb lvextend -l +100%FREE /dev/VolGroup00/LogVol00 resize2fs /dev/VolGroup00/LogVol00 This worked fine. I subsequently filled up the VM, then deleted most of the used disk space. However, the unused disk space was never recovered after I deleted all of the files. This will illustrate what I'm saying better: # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 61G 32G 26G 56% / /dev/sda1 99M 20M 75M 21% /boot tmpfs 1006M 0 1006M 0% /dev/shm # pwd; du -h --max-depth=0 / 5.1G . I cannot figure out how to get the partition to see that only 5.1 GB is used. Any ideas what I'm doing wrong?

    Read the article

  • Windows XP Installation issue - cannot find hard disk

    - by Marco
    A friend of mine gave me a laptop with Windows 8 installed and nothing else. I don't like it so I am trying to remove it by installing Windows XP. I have a windows XP installation CD that I have used before and worked fine, but didn't work when I tried to install it on the Windows 8 machine. It keeps telling me I don't have a drive to install to. Then I log into Windows 8 again and install check partitions. I found 2 and tried to make a new one but it will only let me make one of 69mb. Next, I tied to find a way to go back to XP with BCD install and try to set the boot loader for XP but it wasnt there. Somehow I deleted the bootloader for Windows 8 and now it asks me for a recovery tool for media. I am not familiar with the laptop specs, but it is a Toshiba with about 250GB storage, and above 1GHz processor.

    Read the article

  • Simple Workstation Imaging Solution?

    - by user23087
    I need a fairly cheap imaging solution for Windows XP corporate desktops. Ideally, I'd be able to set up a desktop exactly as we want it, create an image, deploy this image to a server, then boot a new desktop to a CD/USB Drive/Network and quickly set up the workstation. Ideally, each computer would also have a unique workstation name. Any ideas? Right now I'm using a custom built Linux DD solution, but it's slow, not network-based, can't image multiple computers at the same time as there's only one copy on a USB drive, and can't uniquely name the computers. Thanks, Will

    Read the article

  • Lost all data on Windows XP after blue screen

    - by Barb
    I got a blue screen and was trying to boot with my OS disk. Frankly, I was unsure exactly how to do this. I was trying everything and booted in partition mode. Finally, I booted with disk and ran chkdsk /r and was able to log into Windows. But, all of my files and pictures are gone. I have no backup and all I'm sick to think that I lost the last seven years of pictures of my kids. What can I do?

    Read the article

  • Repair GRUB bootloader for multiboot system

    - by user1715324
    I have two hard disks – one a 1TB and the other a 250 GB. I installed the OSes in the following order: Windows 7 on the first hard disk (1 TB) After that Kubuntu 12.04 on a partition (/dev/sdb7) on the second hard disk (250 GB) The second drive also contains an NTFS partition. Now, kubuntu's bootloader was installed on the second hard drive's MBR (and successfully detected Windows 7). So, whenever I wanted to load Windows I used to select the first hard disk from the BIOS boot menu and the second hard disk whenever I wanted to load kubuntu. I know I could have set the second hard disk as the default drive, still I prefered this method. The problem started when I installed Linux Mint 13 on the second hard disk (/dev/sdb3) and overwrote kubuntu's original MBR. Now, the GRUB just detects Mint and Windows. The MBR on the 1 TB hard disk is untouched. Is there a way I can modify the MBR on the second hard disk now so that it will show kubuntu and Mint both?

    Read the article

  • SquidProxy status:Unknow job :Squid

    - by BanKtsu
    I have an issue in Centos 6.3. I installed Squid from compressed source archives(.tar.gz), I create an /etc/init.d/squid file, that run well because I view with the command ps -aux, that is running: root 2153 0.0 0.0 8920 1536 ? Ss 13:52 0:00 /opt/squid/squid-3.2/sbin/squid squid 2155 0.0 0.0 16368 9224 ? S 13:52 0:00 (squid-1) squid 2157 0.0 0.0 3628 972 ? S 13:52 0:00 (logfile-daemon) /var/log/squidserver/access.log This service boot at start because I configurate it with chkconfig chkconfig --list|grep squid squid 0:off 1:off 2:on 3:on 4:on 5:on 6:off The only issue that i have is when i run the command service--status-all status:Unknown job:squid why is not reconized?, what i missed?

    Read the article

  • Create new partition on live production CentOS server

    - by Kimmel
    I have a production server that is running on CentOS. I'd like to create a partition on the server without having to reinstall everything. I have CLI and VNC access to the remote server. Is there anyway that I can create a partition safely? Here's my output from fdisk -l Disk /dev/sda: 85.9 GB, 85899345920 bytes 255 heads, 63 sectors/track, 10443 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00033d5e Device Boot Start End Blocks Id System /dev/sda1 * 1 10444 83885056 83 Linux Thanks.

    Read the article

  • Why is a ZFS pool not persisting over server restart?

    - by Chance
    I have a ZFS pool with 4 drives. It also has a 3gb ZIL and a 20GB L2ARC that are each partitions on an SDD that doubles as my Linux Mint (ver. 13) boot drive. The pool is mounted to /data. The problem I am running into is that when I restart the server the pool/directory is completely wiped despite having data in it prior. I'm afraid I'm doing something wrong in the setup, which leads me to the following questions: What would cause this? Is there anyway to get the data back? How do I stop it from happening in the future? Thank you in advance! pool: data state: ONLINE scan: none requested config: NAME STATE READ WRITE CKSUM data ONLINE 0 0 0 raidz2-0 ONLINE 0 0 0 sda1 ONLINE 0 0 0 sdb1 ONLINE 0 0 0 sdc1 ONLINE 0 0 0 sdd1 ONLINE 0 0 0 logs sde4 ONLINE 0 0 0 cache sde3 ONLINE 0 0 0 errors: No known data errors

    Read the article

  • How would I add a second physical hard drive to proxmox

    - by Cygnus X
    I installed proxmox on a single 250GB hard drive and I would like to add a second identical hard drive to put more VM's on. I already tried once, and didn't get very far. I added it and formatted it as an ext4, but when I went to use the disk, it said only 8GB was available. That's not quite right. So I did some searching and found that I had to make the device ID 8e for a linux lvm. After I did this, it said I had to restart, so I did... and it wouldn't boot!!! What did I do wrong? And how do I do it right? (I know I could throw in a RAID card and do a RAID 0, but I'd rather not).

    Read the article

  • Damaged XenServer Storage LVM partition table

    - by Fiolek
    I have a homeserver running under XenServer control with 3x1TB discs inside, one for XenServer and two mirrored(using Intel's fakeRAID and dmraid) for VMs and a user data(but now I think RAID didn't work). I tried to pass PCI card to VM using PCI-passthroug and I read somewhere that I need to recompile kernel with pciback module but something went wrong(I made mistake in /boot/extlinux.conf and server couldn't run) and I had to use LiveCD of GPartEd(I already had it on USB key) to correct this. But when I re-run the server all VDIs were gone. I have completly no idea what could go wrong. I tried to repair RAID using dmraid -R in the hope that everything will return to noramal but now I think this done more bad than good(and corrupted rest of LVM table...). Is there any possibility to recover this SR or only data from one(~100GB) of VDI? I also wants to apologise for my English, I'm not from English-speaking country and I'm only 16 years old, so I hadn't "time" to learn it(school isn't good place to do this) in sufficient way.

    Read the article

  • Wi-Fi performance in Windows 8 RP on a MacBook Air (mid 2011)

    - by Steven Lu
    I was able to install the Boot Camp Windows software using the executable that it provided, and there are no unrecognized or unknown devices in Device Manager. Wi-Fi works but it seems to be limited to an extremely slow 1.5Mbits. Network Center reports an 802.11n connection (at 65Mbps usually) but transfers never reach above about 200kB/s. Being limited to 1/20th of the connection speed of my internet service is quite frustrating. Does anybody experience the same issue? I have been trying to identify the Broadcom Wi-Fi chipset and a driver that I could try to upgrade to but I have made very little progress on Google on this front.

    Read the article

  • Restore XP on Acer Aspire One netbook

    - by Imran
    I have an Acer Aspire One D250 netbook which came with Windows XP (but no CD) on which I have since installed Xubuntu 9.10. Now I am trying to sell it, but I cannot find a way to recover XP. I have read in a lot of different places that holding Alt+F10 during boot should send me to a recovery menu (which will allow me to restore XP from a "secret partition"), but I have tried many times to no avail. The best I can do is get the BIOS setup screen by holding F2, but there doesn't seem to be any recovery option there. After the initial option to go into the BIOS setup GRUB starts loading and there don't seem to be any more opportunities to enter a system setup screen. Please help!

    Read the article

  • Set-and-forget Windows backup software with NAS-support?

    - by Evert
    I am looking for set-and-forget backup software for Windows (Vista & 7, and if possible XP/2003). The idea is that it runs in the background on the clients, and does its thing towards a network-share. In case the HDD of one of these clients spontaneously combusts, all I want to have to do is: replace the drive, insert a USB-stick, boot from it, and restore the machine. It should support drives which use [ICH]-RAID. What are my options here? It looks like WHS meets all the requirements, but I am curious about my other options here.

    Read the article

  • Windows activation on a Virtual Machine (Physical->VM)

    - by Daisetsu
    I backed up a number of laptops to virtual machines before they are to be re-purposed, in case I need the data at some later time. While the Physical to VM processes worked fine I am encountering issues on some of the VMs. When I boot them I get an error message saying I MUST activate windows in order to login. This is expected because the hardware changed (from physical hardware to virtualized hardware). I click the OK button and expect to be prompted with ways to activate, windows sits there for quite a while then tells me that "Windows has already been activated". I click OK at that message and get take back to the beginning where I am asked to activate Windows. I have done some fairly intensive googling but haven't been able to find a real solution. EDIT: The laptops with the issues are 2 Sony Vaios, I believe that they have the OEM version of the OS originally installed by the factory.

    Read the article

  • Grub install fails while installing Ubuntu on RAID

    - by Warren Pena
    I'm trying to install Ubuntu 9.10 using the alternate install CD, but I keep getting stuck. I get through the first few steps of the install process easily enough (telling it what partition to install to, what user ID and password to create, time zone, etc.), but then it suddenly pops up a menu asking me what the next step in the install process is. It has "Install the GRUB boot loader on a hard disk" selected by default. When I select it, it goes to another screen with a progress bar and a label "Installing the 'grub2' package." The progress bar gets to 16%, and then I get returned to the same menu. No matter how many times I try to install grub, the exact same thing happens. I'm trying to install Ubuntu on a two disk RAID-1 array. This is the RAID card I'm using: http://www.siig.com/ViewProduct.aspx?pn=SC-SAER12-S2. Any ideas what may be causing this to happen and how I can fix it? Thanks!

    Read the article

  • Change from IDE to AHCI after installing Windows 8

    - by Louis
    I had my drive controller configured for IDE when I installed Windows 7. This didn't change when I upgraded to Windows 8. I now need to enable AHCI, but doing so causes Windows to fail to start. It doesn't know how to automatically fix the problem. I was able to use Regedit from the recovery area, in order to try using this fix that worked for Vista. That key is missing in Windows 8, however. I read that the relevant key is now in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\storahci. But my settings already match the changes they suggest making. How can I get Windows to boot after enabling AHCI in the BIOS?

    Read the article

< Previous Page | 313 314 315 316 317 318 319 320 321 322 323 324  | Next Page >