Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 319/1359 | < Previous Page | 315 316 317 318 319 320 321 322 323 324 325 326  | Next Page >

• Dell Laptop's Bluetooth isn't detected by Ubuntu

  - by vishwaje

  I have Dell vostro 3500 Laptop. I Installed Ubuntu 12.04. It doesn't detect my bluetooth. below is my information. lsusb | grep Bluetooth Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) lsmod | grep bluetooth bluetooth 158438 10 bnep,rfcomm rfkill list 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: no (wifi working fine. I disabled it using network menu. So, it's fine) dmesg | grep Bluetooth [ 21.981835] Bluetooth: Core ver 2.16 [ 21.981872] Bluetooth: HCI device and connection manager initialized [ 21.981877] Bluetooth: HCI socket layer initialized [ 21.981881] Bluetooth: L2CAP socket layer initialized [ 21.981891] Bluetooth: SCO socket layer initialized [ 21.986047] Bluetooth: RFCOMM TTY layer initialized [ 21.986059] Bluetooth: RFCOMM socket layer initialized [ 21.986065] Bluetooth: RFCOMM ver 1.11 [ 22.361783] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 22.361791] Bluetooth: BNEP filters: protocol multicast So How can I fix this? I saw other place (I don't remember which site) They said, some times, when in windows, if bluetooth disabled by windows driver, It can't be enabled by linux. So, I should install windows and enable blueethooth from windows and then re install linux. That is impossible for me, because I don't have Windows installation media. But I tried this, which is I installed windows xp on virtual box. Vbox showed me thow unknow USB devices. I connected them and installed windows bluethooth drivers to xp. But it didn't ditected Bluethooth either. Also, when I set off mode in hardware switch, those unknown devices disappear from Vbox usb device seletcion menu. So, they are definitely something to do with wifi or bluethooth. Please help me..

  Read the article

• Failure to Boot 12.04 on HP AMD Dual Core. Rescue Mode doesn't even come up

  - by L R Bellmore Jr

  I have 12.04 installed on HP 64 bit dual core AMD laptop.. worked great until about 1-2 months ago.. now takes 1/2 hour to 25 hours to boot if it ever does. A minor number of times I get the HP logo with hash lines on screen and it just hangs... When it finally boots 95% it will run until I turn it off days later to see if any of the upgrades fixed the problem. Currently, if it boots, it is random.. .left on over night .. 2 nights ago and came back to a HP logo with Hash Lines horizontal across the screen.. frozen.. rebooted back to black screen.. no HP logo... Most often when it does boot.. no HP logo.. just cursor shows up.. and then I know it will finally load... computer has been made worthless and it is my work computer..HELP PLEASE... Rescue Mode can't be invoked.. computer doesnt respond.. has shown up 3 times in about 100 and when I have tried it... 1 time it resulted in a boot up but then failed in a couple hours.

  Read the article

• juicy couture sale would nanytime go for any added casting

  - by user109129

  Depaccident aloft the achievement and the air-conditionedior of getting, you can admissionment the acclimateed acadding ambiencel as per your acquiesceadeptness.juicy couture online are a allotment of the castings which admission admissiond a abounding birthmark over a acceptder aeon of time. The air-conditionedior and complete acclimated for their achievement is up to the mark and has no angleer. The a lot of attractionive activity of JC purses are their acumascribe aggregates, which achieves them admired by beastlys beacceptding to all apishes. These are simple to be admissionmentd from onbandage retail aliment. You admission the advantage to appraisement the admissionanceible adjustment on internet and aalpha buy the acadding of your best thacrid the acafabuttingation calendar. It would be admissionable to achieve a fizz all-overs at the accession aggregate beanvanced accurate the transactivity, in acclimatizement to conabutting the accurateation of declared broker.Alacquireing, tachievement are so aapprenticeding advantages in the exchange that it has in fact beappear difficult to achieve the acclimateed best, but if you alattainable admissionment juicy couture sale, you would nanytime go for any added casting. Their beside attaccident with adjustment of blooms is the best activitys which a exhausted woman may annual for. The bandage of these tots is in fact able, and they do not aperture out even afterwardss acrid and added acquireing.acclimateed admeaconstantments of Juicy couture battleaccoutrements achieve them applicative to accouterment arbitrary admeaconstantment requirements. Some woman like huge accoutrements while addeds like acclimatized admeaconstantmentd tots. In any case, the cobasicotmentments of these purses are bottomless and admission the acclimateation to acclimatize sanytimeal sbasic activitys. The admirable and dejected bloom abuttals is anadded complete aspect of JC getting. acquire the acclimateed ones for you accordanceing to the accumulating of your accoutermentss, and leave a ambrosial afterwardseffect on addeds. abonfire and acclimateed contrasts are in trend nowacanicule, so accrue yourself up to date by purchasing this air-conditionedb accumulating from Juicy Couture.

  Read the article

• How to Reinstall Ubuntu on Acer C7 Chromebook

  - by Daniel

  I installed Chrbuntu 13.04 recently and it works great, however I was updating some programs when a pop-up appeared asking if i wanted to upgrade to the newest version. I didnt realize that it was still unstable and buggy. I am unsure on how to do this. Ive been told that i need to wipe the ubuntu partition completely but i dont see why that is neccesary. Basically i want to remove ubuntu 13.10 and use the partition it is installed on to install 13.04. Sorry for being a noob on linux but i hope you can help, And thanks for your time.

  Read the article

• Can't connect to WIFI after sleep Ubuntu 14.04

  - by user3380404

  After an upgrade over a previous version to Ubuntu 14.04 I have problems with connecting to WiFi. After suspending it won't reconnect to any existing network unless I restart the laptop. sudo lshw -C network: *-network description: Ethernet interface product: 82567LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:27:13:b4:d3:58 capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=2.3.2-k firmware=1.8-3 latency=0 link=no multicast=yes port=twisted pair resources: irq:45 memory:fc200000-fc21ffff memory:fc225000-fc225fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:c6:6b:c8 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-29-generic firmware=8.83.5.1 build 33692 ip=10.0.1.160 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:48 memory:f4200000-f4201fff

  Read the article

• GParted wont resize extended partitions

  - by Magnum Frost

  I have dual booted windows 7 and Ubuntu 12.04 LTS and have decided that I need more space on my Ubuntu partition. I used gparted on a Live CD to shrink my Windows 7 partition (/dev/sda3) but when i try to resize the extended partition (/dev/sda4), which houses my linux partition (/dev/sda6), the right click options are greyed out and there is a key next to the extended partition. I have resized the partitions within the extended partition before to provide room, but now I can go no further with that, and need to grow the extended partition. The free space lies to the left of the extended partition and there is a small amount of free space directly to the right as well. Also, within the extended partition is /dev/sda5 (ntfs) , which I have no idea what is on it, but most of the space (3.42GB) is used, /dev/sda6 (ext4, mount point: /), my partition containing Linux, and /dev/sda7 (linux-swap). I hope you guys can help me with this because I really don't want to screw something up while trying to resize the extended partition.

  Read the article

• Ubuntu 12.04 suddenly will not boot after compiz crash on lockscreen

  - by schonjones

  Yesterday i went to work and closed my laptop. When i got home I couldn't get the lock screen to come back up. ctrl+alt+f2 to get to a terminal and Tried to kill compiz, compiz was not running so I tried to restart it got an error opening the display so i tried to restart lightdm again couldn't open display. so I restarted and now I am stuck on the loading screen. I tried booting in recovery mode and all options hang except root, but i'm stuck with read only. booting from a live cd I can mount the drive but again stuck with read only. I'm completely stuck here. checking my default-display-manager returns "/usr/sbin/elsa" as the only line and can't edit it. I've got an 11.10 live cd and my /home is encrypted so i can't try to back anything up at the moment either. How can i resolve this or at the least back up some of my data? Please help!

  Read the article

• Battery Indicator Missing

  - by Edwin

  Duplicate of: No Battery Status Icon I have just recently upgraded from 11.04 "Natty Narwhal" to 11.10 "Oneiric Ocelot" on my laptop, but do not have any battery indicator (which should be located between the volume and date indicator in Unity). I have already run sudo apt-get install indicator-power and got the following output: Reading package lists... Done Building dependency tree Reading state information... Done indicator-power is already the newest version. indicator-power set to manually installed. The following packages were automatically installed and are no longer required: //list of packages Use 'apt-get autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. In addition, I have already tried reinstalling, but still don't have a battery indicator. What else can I do?

  Read the article

• Is it possible to get the old workspaceswitcher back in the top-panel?

  - by Arne

  I just updated my Ubuntu from 10.04 to 12.04 yesterday and so far I'm very satisfied with it. There is only one thing which is still missing to get back just the same comfort as I had with the previous version. I work on 4 workspaces and would like to have the ability to switch from one to another by just one click. With Gnome there was the possibility to add the workspace switcher to the top-panel next to the system tray and I could easily click on just the workspace I wanted to switch to. Of course there I could switch by using the keyboard shortcuts, but I would like to use the mouse in addition. I don't like using the switcher on the left side because it's much slower. Is it possible to get the old workplace switcher back in the panel at the top?

  Read the article

• Enable wireless on Dell Inspiron 1300

  - by Simon

  As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

  Read the article

• How do I EFI boot Zenbook Prime UX31A from built-in card reader?

  - by Richard Ayotte

  How do I EFI boot Zenbook Prime UX31A from built-in card reader? Ubuntu 12.10 64bit has been copied onto an a SD card which I'm trying to boot from. When I power on my Zenbook and press ESC, the SD card isn't an option. There is an "Add boot option" in the BIOS but it requires a few a things that I'm not quite sure of. Add boot option - I guess any identifier works here. I've been entering ubuntu. Select Filesystem - The only option available is PCI(1F|2)\DevicePath(Type 3, SubType 12)HD(Part1,Sig787e6287-xxxx-xxxx-xxxx-xxxxxxxxxxxx) Path for boot option - I've been entering ubuntu:\EFI\BOOT\BOOTx64.EFI Then I select Create and the new boot option appears in the boot menu but it doesn't work.

  Read the article

• Titanium SDK gives a "file too short" error

  - by Dananjaya

  I'm using Ubuntu 11.04 and recently installed Appcelerator Titanium Studio version 1.7 When I load up a demo project to run, I get an error like this, Couldn't load file:/home/dananjaya/.titanium/runtime/linux/1.1.0/libkhost.so, error: /home/dananjaya/.titanium/runtime/linux/1.1.0/libwebkittitanium-1.0.so.2: file too short Am I missing some dependencies here or is it a bug in the application? Thanks in advance.

  Read the article

• Extremely slow upload speeds in nautilus with FTP

  - by Oscar Godson

  I was at home uploading a WP site and it's maxing at 4.2kb. I did a speed test and im getting ~1MB upload (my home ISP caps it out at that). I uploaded a 5MB file via Chrome, to test, and it uploaded within 2 mins. The file uploaded was a wordpress.xml file through the uploader. Same file in nautilus is taking forever. To upload this WP site and all the plugins took 1 hour. Any ideas of why or how? P.S. I've been using my hosting company also for years and they've never had any speed issues uploading.

  Read the article

• How do I install root-cern?

  - by Rick Turd

  Cern's ROOT environment installs fine on 10.10, and is even available in the Software Center, but it will not install or compile on Natty because the x11 directories are in new locations. I can redefine the paths, but then I get compile errors because only gcc 4.3 is supported through ROOT and Natty uses 4.5. I've given up and gone back to 10.10, but my question is, after installing ROOT on Maverick, if I upgrade back to Natty, will my old software still work with these new directory paths?

  Read the article

• Ubuntu comes with firewall by default?

  - by LuC1F3R

  I understand the Ubuntu comes with firwallul UFW is true? There is a GUI for it? if so, what is his name and where do I download? It is possible that UFW notify us (like in windows with a pop-up windows)when someone wants access to your pc or when an application wants to go out on the internet? Is there any firewall for ubuntu notify you when someone wants access to your PC or when an application wants to access the Internet?

  Read the article

• Error when running debuild on package source

  - by Chris Wilson

  I'm attempting to build the squeak-vm source but am getting an error every time I do so. The output is: dpkg-buildpackage -rfakeroot -D -us -uc dpkg-buildpackage: export CFLAGS from dpkg-buildflags (origin: vendor): -g -O2 dpkg-buildpackage: export CPPFLAGS from dpkg-buildflags (origin: vendor): dpkg-buildpackage: export CXXFLAGS from dpkg-buildflags (origin: vendor): -g -O2 dpkg-buildpackage: export FFLAGS from dpkg-buildflags (origin: vendor): -g -O2 dpkg-buildpackage: export LDFLAGS from dpkg-buildflags (origin: vendor): -Wl,-Bsymbolic-functions dpkg-buildpackage: source package squeak-vm dpkg-buildpackage: source version 1:4.0.3.2202-2 dpkg-buildpackage: source changed by José L. Redrejo Rodríguez <[email protected]> dpkg-source --before-build squeak-vm-4.0.3.2202 dpkg-buildpackage: host architecture i386 fakeroot debian/rules clean dh_testdir dh_testroot rm -f build-stamp configure-stamp rm -f unix/cmake/config.sub unix/cmake/config.guess /usr/bin/make -f debian/rules unpatch make[1]: Entering directory `/home/notgary/Projects/squeak/squeak-vm-4.0.3.2202' QUILT_PATCHES=debian/patches \ quilt --quiltrc /dev/null pop -a -R || test $? = 2 Patch linex.patch does not remove cleanly (refresh it or enforce with -f) make[1]: *** [unpatch] Error 1 make[1]: Leaving directory `/home/notgary/Projects/squeak/squeak-vm-4.0.3.2202' make: *** [clean] Error 2 dpkg-buildpackage: error: fakeroot debian/rules clean gave error exit status 2 debuild: fatal error at line 1337: dpkg-buildpackage -rfakeroot -D -us -uc failed

  Read the article

• Xmonad Xsession

  - by AntLord

  My user level: noob-ish, so please bear with me I'm running 12.04 LTS. I have installed and, to some extent, configured xmonad 0.10 The "automagically" created xsession for it works fine as it is, but when I login it won't run a startup script I've created and "call from" /usr/share/xsessions/xmonad.desktop, if that's right. I've read pretty much all I could find about .xinitrc and .xsession, I tried that and it somehow messed up the other "sessions", if I'm explaining myself correctly. Had to $unity --reset to have the "main session" working again. Anyway, my question is, how do I autostart xmobar and set a desktop background after login into xmonad's default Xsession? I tried this script, start-xmonad: #!/bin/bash # #I only used one of the following each time I tried, none worked #Also, do I really need the '&'? I know what they're for, but... nitrogen --restore & feh --bg-scale ~/Pictures/picture.png & #Then I want xmobar to start, again do I need the '&'? I know it's for it to run #in the background, but I tried removing the '&' and xmonad still launched xmobar & #Finally, the only thing that seems to work in this script exec xmonad Yes, I made sure I did chomd +x ~/start-xmonad The xmonad.desktop is [Desktop Entry] Name=XMonad Encoding=UTF-8 Comment=Lightweight tiling window manager Exec=/home/myusername/start-xmonad Icon=custom_xmonad_badge.png Type=XSession So, this didn't work, now I'm here. Please help :s thanks

  Read the article

• Keyboard shortcuts don't work continuously

  - by T. K.

  First I had the problem of the keyboard layout resetting itself on each reboot from DE (german) to EN (us). I followed the advice of using dconf in order to make the DE layout my personal default (see Keyboard layout switches to English each time I reboot). However, after that, my shortcuts didn't work properly anymore. In Firefox, Kile etc. everything works fine while in Nautilus, copying/erasing/pasting is impossible even when I change the keyboard layout back to En (us). Also, I'm not even able to select multiple items using the cursor in Nautilus while every acts normal on the desktop. It's quite confusing. I've read about a similar bug (see https://bugs.launchpad.net/unity/+bug/1226962) but since German is a latin language there is no appropriate solution given for my problem. Any help is really appreciated here. Edit: The third reboot resolved the problem so the shortcuts finally work in Nautilus again. Still, selecting multiple objects using the cursor isn't possible.

  Read the article

• Adding a ppa repo and get key signed - no valid OpenPGP data - proxy issue?

  - by groovehunter

  I want to get a ppa key signed I tried apt-key adv --keyserver keyserver.ubuntu.com --recv-keys A258828C Executing: gpg --ignore-time-conflict --no-options --no-default-keyring --secret-keyring /etc/apt/secring.gpg --trustdb-name /etc/apt/trustdb.gpg --keyring /etc/apt/trusted.gpg --primary-keyring /etc/apt/trusted.gpg --keyserver keyserver.ubuntu.com --recv-keys A258828C gpg: requesting key A258828C from hkp server keyserver.ubuntu.com gpgkeys: HTTP fetch error 7: couldn't connect to host gpg: no valid OpenPGP data found. gpg: Total number processed: 0 and wget -q http://ppa.launchpad.net/panda3d/ppa/ubuntu/dists/lucid/Release.gpg -O- | apt-key add - gpg: no valid OpenPGP data found I am behind a proxy , in apt.conf it is configured correctly Acquire::http::Proxy "http://proxy.mycompany.de:3128"; I also tried setting proxy export http_proxy="proxy.mycompany.de:3128" export https_proxy="proxy.mycompany.de:3128"

  Read the article

• How do I install a Wimax usb driver?

  - by kakaz

  I am using wimax usb modem in Ubuntu 9.04 properly. I am familiar with Ubuntu 10.04 and try to install the same deb file to use my wimax USB modem, but it could not install and give me the following error message: $ sudo dpkg -i green-packet-wimax-usb_i386.iso.deb (Reading database ... 206628 files and directories currently installed.) Preparing to replace green-packet-wimax-usb 1.12 (using green-packet-wimax- usb_i386.iso.deb) ... /var/lib/dpkg/info/green-packet-wimax-usb.prerm: 45: /etc/init.d/wimaxd: not found Removing any system startup links for /etc/init.d/wimaxd ... FATAL: Module mt7118_usb_os not found. Unpacking replacement green-packet-wimax-usb ... Setting up green-packet-wimax-usb (1.12) ... FATAL: Error inserting mt7118_usb_glue (/lib/modules/2.6.32-28-generic/kernel/drivers/net/mt7118_usb_glue.ko): Invalid module format dpkg: error processing green-packet-wimax-usb (--install): subprocess installed post-installation script returned error exit status 1 Processing triggers for ureadahead ... Processing triggers for desktop-file-utils ... Processing triggers for python-gmenu ... Rebuilding /usr/share/applications/desktop.en_US.utf8.cache... Processing triggers for libc-bin ... ldconfig deferred processing now taking place Processing triggers for python-support ... Errors were encountered while processing: The error (Line 9) give me some clue that the mt7118_usb_glue.ko kernel object can't insert it. So, I think this may be due to it's kernel dependencies. Can anybody tell me how I can install this kernel object to my new Ubuntu 10.04 kernel?

  Read the article

• How to enable Mic in Wine (pulseaudio)

  - by Postadelmaga

  I'm not able to make mic work with wine 1.5 I found some suggestions but they don't seem to work: -Disable winepulse.drv (aka: PulseAudio): "A1: Go to winecfg, in the tab 'libraries', enter 'winepulse.drv' in the box and click on add, click yes on the warning. Select winepulse.drv and change load order to 'disabled'. Now try to trigger your bug again, if it was a winepulse bug it shouldn't trigger any more. A2 (easier and preferred): From 1.5.3 onward, launch your program with WINENOPULSE=1 wine program.exe to temporarily disable winepulse for that program." reference: http://ubuntuforums.org/showthread.php?t=1960599

  Read the article

• How to repair GRUB from backup?

  - by titusjaka

  I have Windows 8 and Ubuntu 13.04 in dualboot. But the problem was that Windows didn't boot when GRUB is set as primary bootloader in BIOS. When the Windows EFI partition was checked as primary, Windows booted well. Then I decided to fix it and installed Boot-Repair. First of all, I made the backup. Then updated the GRUB. The update was successful. But then Windows and Ubuntu didn't boot at all. I've repaired GRUB using live-USB. Now I can boot Ubuntu, but Windows doesn't boot. How can I restore boot partitions from Boot-Repair backup (.zip file)?

  Read the article

• Emacs editor copy and deletion

  - by Null pointer

  I am a huge fan of emacs.. But even after 1 year of practising on emacs I am unable to solve these three annoying issues about emacs please help me! 1.Whenever I want to copy the content from emacs into other things such as a website textarea I have to use GUI copy button because ctrl+w doesn't work. Is there any way to do this from emacs-command line. 2.Whenever I delete something using ctrl+shft+SPC or ctrl+k etc I don't want it to be stored in kill ring how do I do it(I know ctrl+D does this but it deletes only one char at a time)? 3.Whenever I select text by mouse and press backspace then text goes into kill ring(Which I want to change as mentioned) but same doesn't happen when I select text with ctrl+SPC(set mark) and then ctrl+f/ctrl+b etc. Please help me! Thanks in Advanced!

  Read the article

• How to replace nss with new version 11.10 64bit

  - by Gary S

  I need a specific version of NSS 3.12.4. I have a simple java crypto (Sun-pkcs11) test and it works with the default nss setup from Ubuntu 11. (pointing to /usr/lib/x86_64-linux-gnu where all the libnss*.so files live) But when I point specifically to the custom 3.12.4 lib folder, it doesn't work. The only way to get it to work is to set the LD_LIBRARY_PATH to point to the new folder. So what is the preferred way to 'swap in' a new nss module? Do I need to overwrite any matching .so files in /usr/lib and /usr/lib/x86_64-linux-gnu? Should I use an install command? Point is, I don't think I should have to use LD_LIBRARY_PATH.

  Read the article

• Cannot see boot options after editing grub background

  - by cipricus

  After solving this problem I managed to get myself into truble again out of nothing by trying to change the display of the dual boot option page in Boot Customizer. I have changed the background, the fonts size (I have increased them) and font style (I have chosen UnDotum). But Boot Customizer gave me an error (I mean a message that the application was closed unexpectedly or smth). I have restarted BootCustomizer and the settings were there. When I rebooted, instead of the normal boot options list, just the background image that I had selected and nothing else. I used Boot Repair to repair grub, it says it did it successfully, but I still get the background image when I try to boot. Any ideas? (Could it be the matter that I chose UnDotum font style? That was installed in Lubuntu - but how could it be accessible in displaying boot options?) The contents of etc/default/grub are: # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" I have tried to modify etc/default/grub: GRUB_HIDDEN_TIMEOUT=0 to 10 GRUB_HIDDEN_TIMEOUT_QUIET=true to false and GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" to "" but it doesn't help Also, using Shift doesn't make the list visible. I am looking for something like a command that would reset grub options to default. [When trying to reinstall grub i get to this window in term:

  Read the article

< Previous Page | 315 316 317 318 319 320 321 322 323 324 325 326  | Next Page >