Search Results

Search found 28895 results on 1156 pages for 'ubuntu gnome'.

Page 320/1156 | < Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• Ubuntu 11.10 Unity - all Windows decorations disappear after I maximize any window

  - by korda

  When I maximize some of the windows all decorations disappear (by all, I mean on all windows)... Is that common issue on Unity or I'm just unlucky to have some prone to that bug configuration? Anyone have idea how to fix this? EDIT: It won't fix after unmaximize. It seems like maximazing window simply crashes window decorator. Decoration isn't displayed for all existing windows and any new ones. Only way I found to fix this is to run compiz --replace (but this ruins current windows placement - all windows end up on same desktop). It happens almost every time I maximize window.

  Read the article

• Can't connect to Wireless Network - Ubuntu 12.04 LTS & Sabrent A111N USB Dongle

  - by Ohgodwhy

  I've been trying to connect to this network for quite some time. I can't directly connect to the router with a Wire, but can access the Router with other wireless devices without any issues. I had previously tried several other Wifi nic's but none of them would load properly. Today, i went and bought a new (supported) Sabrent A111N USB Dongle, which said explicitly that it works with Linux 2.4 +. I popped the Dongle in, and low-and-behold it immediately said that there were Available Wireless Connections. I selected my connection and tried to connect, but it just loops constantly while saying Wireless Disconnected then attempts to connect again over and over. ifconfig and iwconfig both show my device in a ready and working state. However, iwlist wlan0 scan says that there are no results found. I don't get it... At one point, I could see the CPU in the DHCP client list under the router, but it doesn't fully make the connection (something about a timeout?). Any help would be appreciated. Bus 001 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN

  Read the article

• Ubuntu 12.04 forgetting XModmap settings often

  - by PKKid

  I have the following contents in my ~/.Xmodmap file. It seems a couple times a day (without rebooting or logging out) I need to rerun the command "xmodmap ~/.Xmodmap" to reset my settings. The only thing I can think is that it seems to happen when I walk away from my computer for a bit. Maybe it forgets the settings when the computer locks itself? remove control = Control_L remove mod1 = Alt_L keycode 64 = Control_L keycode 37 = Alt_L add control = Control_L add mod1 = Alt_L Anyone else seeing similar issues?

  Read the article

• how to add programs to ubuntu without internet access

  - by captainandcoke

  I don't have internet access at my home and it takes me about a half hour to ride my bike to the library. I have downloaded .deb files to try to install at my home computer but everyone I have downloaded says it can't install because it depends on package X. The next day I will download package X and it will require package Y. Is there anyway to find out what ALL the sub-dependencies are for deb files? I have tried to boot from USB or External Hard drive on the library computers but the security settings prevent this. Also, I do not know anyone with a Linux computer.

  Read the article

• cannot add or remove programs using ubuntu software center (USC)in Kubuntu 12.04

  - by Suhail cholassery

  I am using Kubuntu 12.04,currently.Recently ,I updated my system with update manager and downloaded USC from muon software center which was pre-installed in this system. I could download a lot of softwares such as: -firefox -XBMC media center -VLC media player But when I tried to get some more softwares using USC, after rebooting there began the problem . It does not begin either downloading or instaling the program. When I tried to download the same program using muon software center it showed the following: Unable to obtain the package at this time Another application seems to be using the package system at this time. You must close all other package managers before you will be able to install or remove any packages. I am quite sure that have closed USC . I tried to remove USC, assuming that it caused the problem using muon software center but the result was same.Now I cannot add or remove any programs into my system & I don't know what to do . Please help me as soon as possible.

  Read the article

• Ubuntu is not detecting my android device

  - by user3514160

  I am new to android. I have just downloaded and installed android sdk. Now when I run the application from eclipse, my device is not getting detected. I have googled and was brought up with this as my solution, but that also didn't worked. Here's the 51-android.rules SUBSYSTEMS=="usb", ATTR{idProduct}=="0bb4", ATTR{idProduct}=="0c03", MODE="0666", GROUP="plugindev", OWNER="<username>" After that I rebooted my laptop, and ran this command: username@laptopname:~/Android/adt-bundle/sdk/platform-tools$ adb devices The output i get is: * daemon not running. starting it now on port 5037 * * daemon started successfully * List of devices attached ???????????? no permissions EDIT crazydeveloper@crazydeveloper:~$ lsusb Bus 002 Device 004: ID 0bb4:0c03 HTC (High Tech Computer Corp.) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 04f2:b337 Chicony Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub crazydeveloper@crazydeveloper:~$ ls -l /dev/bus/usb/004/ ls: cannot access /dev/bus/usb/004/: No such file or directory crazydeveloper@crazydeveloper:~$ Edit: 2 After the answer submitted here's the output that i got: crazydeveloper@crazydeveloper:~$ ls -l /dev/bus/usb/002 total 0 crw-rw-r-- 1 root root 189, 128 May 7 09:45 001 crw-rw-r--+ 1 root root 189, 129 May 7 09:45 002 crw-rw-rw- 1 root plugdev 189, 130 May 7 09:48 003 I am using Micromax Canvas 2.2 A114 - Android Version 4.2.2 Please help me. Thanks.

  Read the article

• Trouble using Canon MG 2440 printer in UBUNTU 14

  - by user264795

  I connected usb serial cable from printer to computer. The drivers has been installed automatically. I printed the test page - it was printed. I tryed to print an image - it stays with status - processing... and dont work. Test page also cant be printed. What a problem? I dont know exactly, but I think I use "CUPS" manager and drivers... now status Waiting for printer to become available. And do not print.

  Read the article

• Problem Trying to Install ROOT (by CERN) on Ubuntu 11.04 i386

  - by Jose Luis

  I hope you can help me with this problem I am trying to install root in my computer, but I have a problem and I don't know what to do to solve it I've downloaded the tar file with the root version that I want to install I've extracted the files in the tar file I've run the configure program succesfully, but when I run "make" command I get this result: cp /root/root/core/utils/src/RClStl.cxx core/utils/src/RClStl_tmp.cxx bin/rmkdepend -R -fcore/utils/src/RClStl_tmp.d -Y -w 1000 -- -pipe -m32 -Wall -W -Woverloaded-virtual -fPIC -Iinclude -DR__HAVE_CONFIG -pthread -UR__HAVE_CONFIG -DROOTBUILD -I/root/root/core/utils/src -D__cplusplus -- core/utils/src/RClStl_tmp.cxx g++ -O2 -pipe -m32 -Wall -W -Woverloaded-virtual -fPIC -Iinclude -DR__HAVE_CONFIG -pthread -UR__HAVE_CONFIG -DROOTBUILD -I/root/root/core/utils/src -o core/utils/src/RClStl_tmp.o -c core/utils/src/RClStl_tmp.cxx In file included from core/utils/src/RClStl.h:28:0, from core/utils/src/RClStl_tmp.cxx:16: core/utils/src/Scanner.h:16:27: fatal error: clang/AST/AST.h: No existe el fichero o el directorio compilation terminated. make: * [core/utils/src/RClStl_tmp.o] Error 1 rm core/utils/src/RClStl_tmp.cxx I don´t know what to do Please, help me thank you in advance

  Read the article

• How to Boot from iRAM Solid State Drive on Ubuntu

  - by quickshiftin

  I've got an iRAM solid state drive. I'd like to use this to store a linux root filesystem; the trouble is the device is not recognized as a hard drive to the BIOS. It only shows up if a live CD environment is loaded and the scsi drivers are available (may be other drivers needed as well). I've heard of Boot to Ram and wonder if some variation of that could work here and I could run a linux install off the iRAM??

  Read the article

• Ubuntu 11.10 UI changed suddenly?

  - by VeeKay

  10 64 bit on a Dell laptop that has 6GB RAM and 1GB graphic card. All of a sudden there were some sudden changes in UI which I am unable to understand why. The unity panel was initially glassy and transparent, now it looks all black in its background. Likewise the alt+tab graphics was working well until it got changed suddenly and now shows icons on pure white background. I've not tried to install any themes and I've not tried to tweak anything. Why did this UI changes occur? Could it be that it is unable to detect the graphic card or something? How can I fix this and how can I get back the original desktop back? Please help..

  Read the article

• Ubuntu 12.10 hangs on checking battery state

  - by Waxolunist

  I have a Thinkpad X230. After a boot it hangs with checking battery state [OK]. A second boot is most times successful. What I have seen in other posts doesn't fit to my problem, because My graphics card is Intel 3rd Gen Core processor Graphics controller (not nvidia) It happens not always I have a fresh installed 12.10 with the latest updates (no upgrade) Does anyone experience the same issues or has a solution?

  Read the article

• installing ubuntu 10.04 over top 11.04

  - by Alex

  im looking to install 10.04 over top the 11.04 partition, it wouldnt let. keeps giving me a "root file system not found" error ever time i manually select partition. (i have a win7 partition) 11.04 popped up after upgrade that my hardware isnt supported for unity. and i cant boot into it, hangs up on purple screen right after boot menu. if anyone can post a link to a how to guide or put it on here, would be great? im trying to take advantage of my nvidia geforce gt 120m (its a laptop) to play around with cuda/c++ programming!

  Read the article

• Graphics problems: noise-like glitch, and screen freezes in Ubuntu 13.04

  - by user207253

  I have recently upgraded to 13.04 and am using unity. I am experiencing two intermittent problems with the graphics: 1) All or part of the screen is taken up by 'noise', which lasts for about a second, see screenshot: 2) The launcher panel freezes. I can still move the mouse and the keyboard responds to function keys (I can dim the screen), but I cannot select anything. At the moment I recover by ctr-alt-f1, and restarting lightdm. My computer is a Samsung Chronos 7 laptop, model NP700Z5C, with Intel HD 4000 graphics The same problems occur with lightdm and gdm. I have attempted to install the intel drivers (as the screenshot hints) but these are not indicated as additional drivers in software & updates so I'm not sure whether they are in use. Any suggestions?

  Read the article

• Ubuntu 12.04 Network Connection Unavailable

  - by user211315

  I recently added a EDIMAX EW-7811Un to my computer to allow wireless networking. That was working. Now after a reboot I am unable to connect to either wireless or wired network. the result of ifconfig is ifconfig eth0 Link encap:Ethernet HWaddr bc:ae:c5:46:19:6d inet6 addr: fe80::beae:c5ff:fe46:196d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:231 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:62615 (62.6 KB) Interrupt:51 Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:664 errors:0 dropped:0 overruns:0 frame:0 TX packets:664 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:52639 (52.6 KB) TX bytes:52639 (52.6 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

  Read the article

• Creating Ubuntu Browser App Frames

  - by user73006

  After watching the video i am inspired to create one browser but stuck at one place, could you please help me with this. Requirement = - Like you displayed in your Video i wan create Multiple Buttons in my Toolbar which will open Second ToolBar or Popup Window. - From that Pop Window i wanted to Select Specific Button Which will open My Required Browser. Question - - As displayed in your Video i create new BUtton and If i try to open new link using that it works but now i want to display tool bar or Popup window once any one click on that button, how can i do that.The Second Tool Bar Need to be Activated only after clicking on that button. Things i Tried - - As per my understanding i create Second Toolbar and on that tool bar i have created Button, now i wan know how do i link that tool bar with my Browser Toolbar button. - I tried that by passing Signal Property in Second Toolbar in Quickly but something is missing. MY Code class TvbrowserWindow(Window): gtype_name = "TvbrowserWindow" def finish_initializing(self, builder): # pylint: disable=E1002 """Set up the main window""" super(TvbrowserWindow, self).finish_initializing(builder) self.AboutDialog = AboutTvbrowserDialog self.PreferencesDialog = PreferencesTvbrowserDialog # Code for other initialization actions should be added here. self.refreshbutton=self.builder.get_object("refreshbutton") self.SONY=self.builder.get_object("SONY") self.urlentry=self.builder.get_object("urlentry") self.scrolledwindow1=self.builder.get_object("scrolledwindow1") self.webview = WebKit.WebView() self.scrolledwindow1.add(self.webview) self.webview.show() def on_refreshbutton_clicked(self, widget): print "refresh" def on_urlentry_activate(self, widget): url = widget.get_text() print url self.webview.open(url)

  Read the article

• Ubuntu 14.04 + nvidia-331-updates makes a blank desktop screen

  - by Achint

  I upgraded my installation from 13.10 to 14.04. The problem is that whenever I install the Nvidia drivers from the GUI, upon reboot or trying to login again it only shows the wallpaper of my desktop and nothing else. The mouse does move around, but nothing works. I am unable to open a terminal or do anything else. If I go into the tty console and purge the drivers, then things seem to work again. I have an Optimus setup, with an onboard Intel and discrete Nvidia GTX770M card. It's a 64-bit architecture. I really need to work with CUDA, and was hopeful after hearing that nvidia-prime was released, but this is a real downer. Any help on this?

  Read the article

• Vmware 3D Acceleration Ubuntu 14.04

  - by Bowser5543

  I have installed Vmware Player 6.0.3 build-1895310. The problem I have is that when I run a Windows 7 Vm, it says that 3D support was disabled. (I can't read the exact report atm because it has a chance of crashing my machine.) I have the 3D support box enabled. Here is my graphics card: Mobile Intel® GM45 Express Chipset x86/MMX/SSE2. Can anyone tell me to install drivers or something? I can't find mine anywhere!

  Read the article

• Adobe AIR install problem, Ubuntu x64 14.04

  - by Den Rimus

  Haven't seen this kind of error on askubuntu yet. Did everything as it says here: How can I install Adobe AIR? After sudo ./AdobeAIRInstaller.bin shows this image: dropbox.com/s/wg6cv03h5n1tqgr/adobe_air.png Meanwhile terminal shows a bunch of such messages: (setup:2579): Gtk-WARNING **: Unable to locate theme engine in module_path: "murrine", Nothing is installed. Those murrine - it showed another code before ( another than setup:2579) - I googled it, installed something, it showed another code - I googled it, installed something, etc. Doesn't seem to affect installation anyhow.

  Read the article

• Wake-on-lan under Ubuntu 12.04

  - by iUngi

  I would like to setup the wake-on-lan, the two PCs are connected through a switch. Here is the configuration of the eth0, in the BIOS I couldn't find any information regarding the wake-on-lan. Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) drv probe ifdown ifup Link detected: yes After I shut down the PC, I used different tools to send out the magic package, but nothing happens. Any suggestion?

  Read the article

• Setup suspend-on-lid-close/Fn+F4 outside of KDE/Gnome?

  - by maxschlepzig

  On current Ubuntu (10.04) suspend-on-lid/Fn+F4 only works if some powermanagement-applet of KDE/gnome is running. But what about suspend-to-lid if you are working on the console or using a non-bloated window-manager? What is the current mechanism to configure suspend-on-lid system wide? What of hald/udev/acpid/foo-kit/random-thing is the right place to hook this feature in? What is the up-to-date command to suspend from the command line/script? echo -n mem > /sys/power/state pm-suspend pmi or something else? Btw, if it matters, I want to configure it on some Thinkpads.

  Read the article

• Copy Ubuntu distro with all settings from one computer to a different one

  - by theFisher86

  I'd like to copy my exact setup from my computer at work to my computer at home. I'm trying to figure out how to go about doing that. So far I've figured this much out. On the source computer run dpkg --get-selections > installed-software and backup the installed-software file Backup /etc/apt/sources.list Backup /usr/share/applications/ to save all my custom Quicklists Backup /etc/fstab to save all my network mounts Backup /usr/share/themes/ to save the customization I've done to my themes I'm also going to backup my entire HOME directory. Once I get to the destination computer I'm going to first do just a fresh install of 11.10 Then I'll copy over my HOME directory, /etc/apt/sources.list, /usr/share/appications, /etc/fstab and /usr/share/themes/ Then I'm going to run dpkg --set-selections < installed-software Followed by dselect That should install all of my apps for me. I'm wondering if there's a way/need to backup dconf and gconf settings from the source computer? I guess that's my ultimate question. I'd also like any notes on anything else that might need backed up as well before I undertake this project. I hope this post is legit, I figured other people would be interested in knowing this process and I don't see any other questions that seem to really document this on here. I'd also like to further this project and have each computer routinely backup all the necessary files so that both computer are basically identical at all times. That's stage 2 though...

  Read the article

• Internet slow on one router only [the problem only in Ubuntu] [on hold]

  - by mrSuperEvening

  Internet works perfectly on every other router, but browsing sucks at home (slow browsing and slow loading times). I changed DNS servers to 8.8.0.0, still doesn't help. And funnily, download speed is extremely high on this network (meaning torrents for example), but using browsers and loading websites is extremely slow (only on this network). Do I need to change something in router settings or what can I try? By the way, I use wired connection to router. EDIT: There's no problems when using Windows. EDIT: ifconfig: eth0 Link encap:Ethernet HWaddr f2:4d:a0:c0:3f:4c inet addr:192.168.11.8 Bcast:192.168.11.255 Mask:255.255.255.0 inet6 addr: fe80::f24d:a2ff:fec6:3f4c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:206798 errors:0 dropped:0 overruns:0 frame:0 TX packets:219570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76680734 (76.6 MB) TX bytes:21738160 (21.7 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:160 errors:0 dropped:0 overruns:0 frame:0 TX packets:160 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11094 (11.0 KB) TX bytes:11094 (11.0 KB)` ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (213.159.32.147) 56(84) bytes of data. 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=1 ttl=61 time=0.936 ms 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=2 ttl=61 time=0.937 ms --- google.com ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.936/0.936/0.937/0.030 ms

  Read the article

• Bricscad V12 on ubuntu 11.10!

  - by gabriel

  i tried to install bricscad from the deb file but is for 32bit systems.So i had problems and i downloaded the .tgz file and ran tar -xvf and i was in the directory /opt/bricsys/bricscad/v12 So i managed to run bricscad with the command sudo sh bricscad.sh in the directory this.So my question is, do you have any idea of how to make a launcher or smthing so i can run the program from an easier way?I cannot find it in dash(unity) or in the desktop. Any help will be great! Thanks

  Read the article

• Display artifacts under Ubuntu 12.10

  - by James McMahon

  I am getting some display artifacts under a fresh install of 12.10. (Open image in an another tab to get the full effect) Anyone have any idea what might be going on here or a possible solution? My first assumption was display driver, but I've been have some difficulties getting the Nvidia binary driver to work. So I wanted to check for other possible solutions before I spend a lot of time messing with getting that to work.

  Read the article

< Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >