Search Results

Search found 25088 results on 1004 pages for 'dsl linux'.

Page 322/1004 | < Previous Page | 318 319 320 321 322 323 324 325 326 327 328 329  | Next Page >

• Determine the time difference between two linux servers

  - by Paul

  I am troubleshooting a latency network issue on a network. It is probably a nic or cabling issue, but while I was going through the process of figuring it out, I was looking at the timings of a ping packet leaving a network card and arriving at another server. Both linux. So I have tcpdump running on both, and I issue a ping from one to the other, and back again, and looking at the timing differences might have shed light on where the latency is coming from. It is an academic exercise now, as I need to eliminate some more fundamental causes, but I was curious as to how this could be achieved. Given that ntpd is installed and running on two servers, how can I confirm the current time discrepency between the two servers, to whatever level of accuracy is possible - given that we are talking about latency on a local lan, which is ideally a millisecond or so. NTP itself is accurate to a couple of ms under good conditions, and as both servers are in the same environment, they should (presumably) achieve a similar level of accuracy, and so should have a time discrepency between them of a only few ms - but how can I check this?

  Read the article

• Flexible traffic & bandwidth monitor

  - by BrNathan

  I have looked around, but have not found anything to meet our needs. I need something that can log all connections & bandwidth consumption. We need it for analysis: by protocol, source IP (& MAC if possible), destination, etc. Ideally we are looking for something that can produce custom graphs & also uses mysql. All connections go through one server on a bridged connection (2 network cards) so it is easy to pickup traffic. We are not concerned so much with internal LAN traffic as what passes in & out to the firewall. Thanks for you suggestions. Update: I use Ubuntu 10.04

  Read the article

• I install Ubuntu 13.10 and reboot and im on KDE desktop?

  - by jgamer578

  Hi I'm Jacob and I have no idea what's going on. I installed Ubuntu 13.10 today and was playing around with it for a while and dl'd a bunch of apps from software center and stuff. Eventually I installed steam and (finally) got it working. I downloaded TF2 and had some weird issue where the screen got so distorted to the point I could not play. So I dl'd a driver for my graphics card from the additional drivers app (or whatever it's called) and when it was done I restarted my computer (because it said to.) When the PC booted up it loaded the KDE desktop and I have no idea why. I had unity before I rebooted. Ubuntu 13.10 is the only OS installed on my PC, and I still have all the apps that I downloaded, but I kinda like unity (I started using Ubuntu after they switched to unity) and want it back. Thanks for reading and any help in advance, Jacob.

  Read the article

• Have rTorrent to move .torrent files

  - by David Alvares

  I am running rTorrent 0.9.2 and have configured it to move completed torrents to a different folder with this configuration line: system.method.set_key = event.download.finished,move_complete,"d.set_directory=~/done/;execute=mv,-u,$d.get_base_path=,~/done/" This is working fine, but I would like it to also move the .torrent file that it creates (from a magnet link into the session directory) into this done directory with the same name as the torrent and a .torrent extension. I tried adding another cp command, but I can not seem to figure out which variable ($d.get_hash did not work) stores the torrent's hash (which is what the .torrent files are named in the session directory). Is there a way to do this with rTorrent, if so how?

  Read the article

• Testing home directory scripts by setting $HOME to the location of the test directory

  - by intuited

  I have an interdependent collection of scripts in my ~/bin directory as well as a developed ~/.vim directory and some other libraries and such in other subdirectories. I've been versioning all of this using git, and have realized that it would be potentially very easy and useful to do development and testing of new and existing scripts, vim plugins, etc. using a cloned repo, and then pull the working code into my actual home directory with a merge. The easiest way to do this would seem to be to just change & export $HOME, eg cd ~/testing; git clone ~ home export HOME=~/testing/home cd ~ screen -S testing-home # start vim, write/revise plugins, edit scripts, etc. # test revisions However since I've never tried this before I'm concerned that some programs, environment variables, etc., may end up using my actual home directory instead of the exported one. Is this a viable strategy? Are there just a few outliers that I should be careful about? Is there a much better way to do this sort of thing?

  Read the article

• Search all files containing text

  - by enthdegree

  With Busybox, how do you search for an expression within a bunch of files recursively through a bunch of directories, but only look through text files? We don't know what the file's suffix is going to be; it could be .sh, it could be nothing, it could be something else. I was considering somehow basing the search on encoding although I am not quite sure what the encoding would be either. I've tried busybox grep -r but it searches through binary files too, which wastes a lot of time.

  Read the article

• USB To Serial under OpenSuse 11.3

  - by Exsisto

  I have a LogiLink USB-To-Serial adapter. This has the PL2303 chip inside. When I insert the device: [26064.927083] usb 7-1: new full speed USB device using uhci_hcd and address 9 [26065.076090] usb 7-1: New USB device found, idVendor=067b, idProduct=2303 [26065.076099] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [26065.076105] usb 7-1: Product: USB-Serial Controller [26065.076110] usb 7-1: Manufacturer: Prolific Technology Inc. [26065.079181] pl2303 7-1:1.0: pl2303 converter detected [26065.091296] usb 7-1: pl2303 converter now attached to ttyUSB0 So the device is recognized and the converter is attached to ttyUSB0. When I do screen /dev/ttyUSB0 9600 I get the error: bash: /dev/ttyUSB0: Permission denied So I went looking in the file permissions. ls -l from the /dev folder reports: crw-rw---- 1 root dialout 188, 0 2011-04-26 15:47 ttyUSB0 I added my user lars to the dialout group. When I use the commands groups under lars it shows that I'm in the group. Though I still recieve the permissions denied error, as lars, and as root. I'm trying to connect to a console cable to configure some Cisco switches. My OS is OpenSuse 11.3 x86_64 with kernel version 2.6.34.7-0.7-desktop.

  Read the article

• Ubuntu 10.04 Keyboard and Mouse Freezing Problem

  - by nitbuntu

  I had a partition setup with Windows XP and Ubuntu 8.04 dual booting. I recently upgraded to Ubuntu 10.04 by installing fresh from CD but leaving the previous /home folder as is. Things seemed to be working fine, but started finding that my mouse and keyboard were freezing. After a quick search on the internet, I found the following suggestions as shown here:- Ubuntu Forums Here the suggestion was to:- Edit /etc/default/grub, go to the line that begins like: GRUB_CMDLINE_LINUX_DEFAULT= Change it to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi=off" After that, run this command: sudo update-grub and Reboot This seemed to have resolved the issue but after a couple of days I again find my mouse and keyboard freezing. I also find that my parallel port printer had also stopped working. I have saved the output of dmesg and my syslog. The first can be viewed here but the syslog had too many characters, so if someone can suggest an alternative to freetexthost, I can post it there. Moreover, if there is any other information that should be provided, do let me know. I do hope we can get to the bottom of this issue. Thank you in advance for any help that could be provided.

  Read the article

• KVM CLI install for CentOS 6.3 defaults to Minimal Install

  - by i.h4d35

  So I now I've installed KVM (and its associated tools and packages- libvirt, VMM etc.). On the GUI (i.e using the VMM), installation works as its supposed to. However, when I try to create a VM using the command line interface, the OS (I am working with CentOS 6.3) defaults to a Minimal Install instead of giving me options to choose from at the time of installation. I am trying to install using the following command: virt-install \ --connect qemu:///system \ --virt-type kvm --name testVM2 \ --ram 512 --disk path=/var/lib/libvirt/images/testVM2.img,size=8 --vnc \ --cdrom /media/db18de8e-0853-49fb-80de-5c794d58a46f/CentOS-6.3- x86_64-bin-DVD1.iso \ --network network=default Specifying the OS-type or the OS-variant parameters doesn't make a difference. Is there something that I am missing out on or some other parameter that I must specify? Thanks in advance.

  Read the article

• Improving TCP performance over a gigabit network with lots of connections and high traffic of small packets

  - by MinimeDJ

  I’m trying to improve my TCP throughput over a “gigabit network with lots of connections and high traffic of small packets”. My server OS is Ubuntu 11.10 Server 64bit. There are about 50.000 (and growing) clients connected to my server through TCP Sockets (all on the same port). 95% of of my packets have size of 1-150 bytes (TCP header and payload). The rest 5% vary from 150 up to 4096+ bytes. With the config below my server can handle traffic up to 30 Mbps (full duplex). Can you please advice best practice to tune OS for my needs? My /etc/sysctl.cong looks like this: kernel.pid_max = 1000000 net.ipv4.ip_local_port_range = 2500 65000 fs.file-max = 1000000 # net.core.netdev_max_backlog=3000 net.ipv4.tcp_sack=0 # net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.core.somaxconn = 2048 # net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 65536 16777216 # net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_mem = 50576 64768 98152 # net.core.wmem_default = 65536 net.core.rmem_default = 65536 net.ipv4.tcp_window_scaling=1 # net.ipv4.tcp_mem= 98304 131072 196608 # net.ipv4.tcp_timestamps = 0 net.ipv4.tcp_rfc1337 = 1 net.ipv4.ip_forward = 0 net.ipv4.tcp_congestion_control=cubic net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_tw_reuse = 0 # net.ipv4.tcp_orphan_retries = 1 net.ipv4.tcp_fin_timeout = 25 net.ipv4.tcp_max_orphans = 8192 Here are my limits: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 193045 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1000000 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 1000000 [ADDED] My NICs are the following: $ dmesg | grep Broad [ 2.473081] Broadcom NetXtreme II 5771x 10Gigabit Ethernet Driver bnx2x 1.62.12-0 (2011/03/20) [ 2.477808] bnx2x 0000:02:00.0: eth0: Broadcom NetXtreme II BCM57711E XGb (A0) PCI-E x4 5GHz (Gen2) found at mem fb000000, IRQ 28, node addr d8:d3:85:bd:23:08 [ 2.482556] bnx2x 0000:02:00.1: eth1: Broadcom NetXtreme II BCM57711E XGb (A0) PCI-E x4 5GHz (Gen2) found at mem fa000000, IRQ 40, node addr d8:d3:85:bd:23:0c [ADDED 2] ethtool -k eth0 Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp-segmentation-offload: on udp-fragmentation-offload: off generic-segmentation-offload: on generic-receive-offload: on large-receive-offload: on rx-vlan-offload: on tx-vlan-offload: on ntuple-filters: off receive-hashing: off [ADDED 3] sudo ethtool -S eth0|grep -vw 0 NIC statistics: [1]: rx_bytes: 17521104292 [1]: rx_ucast_packets: 118326392 [1]: tx_bytes: 35351475694 [1]: tx_ucast_packets: 191723897 [2]: rx_bytes: 16569945203 [2]: rx_ucast_packets: 114055437 [2]: tx_bytes: 36748975961 [2]: tx_ucast_packets: 194800859 [3]: rx_bytes: 16222309010 [3]: rx_ucast_packets: 109397802 [3]: tx_bytes: 36034786682 [3]: tx_ucast_packets: 198238209 [4]: rx_bytes: 14884911384 [4]: rx_ucast_packets: 104081414 [4]: rx_discards: 5828 [4]: rx_csum_offload_errors: 1 [4]: tx_bytes: 35663361789 [4]: tx_ucast_packets: 194024824 [5]: rx_bytes: 16465075461 [5]: rx_ucast_packets: 110637200 [5]: tx_bytes: 43720432434 [5]: tx_ucast_packets: 202041894 [6]: rx_bytes: 16788706505 [6]: rx_ucast_packets: 113123182 [6]: tx_bytes: 38443961940 [6]: tx_ucast_packets: 202415075 [7]: rx_bytes: 16287423304 [7]: rx_ucast_packets: 110369475 [7]: rx_csum_offload_errors: 1 [7]: tx_bytes: 35104168638 [7]: tx_ucast_packets: 184905201 [8]: rx_bytes: 12689721791 [8]: rx_ucast_packets: 87616037 [8]: rx_discards: 2638 [8]: tx_bytes: 36133395431 [8]: tx_ucast_packets: 196547264 [9]: rx_bytes: 15007548011 [9]: rx_ucast_packets: 98183525 [9]: rx_csum_offload_errors: 1 [9]: tx_bytes: 34871314517 [9]: tx_ucast_packets: 188532637 [9]: tx_mcast_packets: 12 [10]: rx_bytes: 12112044826 [10]: rx_ucast_packets: 84335465 [10]: rx_discards: 2494 [10]: tx_bytes: 36562151913 [10]: tx_ucast_packets: 195658548 [11]: rx_bytes: 12873153712 [11]: rx_ucast_packets: 89305791 [11]: rx_discards: 2990 [11]: tx_bytes: 36348541675 [11]: tx_ucast_packets: 194155226 [12]: rx_bytes: 12768100958 [12]: rx_ucast_packets: 89350917 [12]: rx_discards: 2667 [12]: tx_bytes: 35730240389 [12]: tx_ucast_packets: 192254480 [13]: rx_bytes: 14533227468 [13]: rx_ucast_packets: 98139795 [13]: tx_bytes: 35954232494 [13]: tx_ucast_packets: 194573612 [13]: tx_bcast_packets: 2 [14]: rx_bytes: 13258647069 [14]: rx_ucast_packets: 92856762 [14]: rx_discards: 3509 [14]: rx_csum_offload_errors: 1 [14]: tx_bytes: 35663586641 [14]: tx_ucast_packets: 189661305 rx_bytes: 226125043936 rx_ucast_packets: 1536428109 rx_bcast_packets: 351 rx_discards: 20126 rx_filtered_packets: 8694 rx_csum_offload_errors: 11 tx_bytes: 548442367057 tx_ucast_packets: 2915571846 tx_mcast_packets: 12 tx_bcast_packets: 2 tx_64_byte_packets: 35417154 tx_65_to_127_byte_packets: 2006984660 tx_128_to_255_byte_packets: 373733514 tx_256_to_511_byte_packets: 378121090 tx_512_to_1023_byte_packets: 77643490 tx_1024_to_1522_byte_packets: 43669214 tx_pause_frames: 228 Some info about SACK: When to turn TCP SACK off?

  Read the article

• Vim Stuck In Insert Mode

  - by Levi Hackwith

  I've been using Vim for several months now via my web host (they allow putty access). All of a sudden, the escape key has become unresponsive. I cannot exist insert or any other mode by simply hitting escape. I have to hit F1 which brings up the help in vim and kicks me into command mode. I'm most certain that my escape key on my keyboard is functioning fine since all of my windows shortcuts that use the escape key operate normally. I know this is a ridiculous question and I'm certain there's a lot more to look into regarding a solution. What I really need is a solid lead as to where to start looking. Things that might help: I'm using vim via putty I'm logging in using jailshell I'm not root

  Read the article

• Would firewire networking be better than 100Megabit ethernet?

  - by Josh

  My office network has a fully switched 1000Megabit ethernet network. I have an Apple iMac with a Gigabit NIC and FireWire, and a Compaq laptop with a 100Megabit NIC and a 4-pin FireWire interface. Accessing my office's shared drives using my laptop is (obviously) much loswer using my laptop than my iMac. Would I see a noticeible performance boost if I enabled Internet Connection Sharing on my iMac and shared the private ethernet network from my iMac with my laptop over FireWire? FireWire is 480Mbit/sec, right? So would I see roughly 4x speed improvement with such a setup?

  Read the article

• Debugging Samba/CUPS printer sharing with Windows

  - by mrdrbob

  I've got a HP Deskjet hooked up to a Slackware 12.2 box. I've got CUPS set up and can print a test page from the box just fine. I've also got Samba set up and have a couple file shares that work fine. I'm trying to share that HP Deskjet out via Samba, but I can't get it to show up in any Windows system. I see the server and its file shares in Windows networking, but when I open the Printers, no printer shows up. Running net view \\servername from the command line lists the file shares, but no printers. Here's the pertinent part of my smb.conf, if that helps: [global] workgroup = HOMENET security = share hosts allow = 192.168.1. 192.168.2. 127. load printers = yes printcap name = cups printing = cups log file = /var/log/samba.%m max log size = 50 [printers] comment = All Printers path = /var/spool/samba browseable = no public = yes writable = no printable = yes guest only = yes Can anyone give me some pointers as to where to start looking for potential causes? Update: Running testparm shows no errors. Here's the output (minus the file shares): [global] workgroup = HOMENET security = SHARE log file = /var/log/samba.%m max log size = 50 printcap name = cups hosts allow = 192.168.1., 192.168.2., 127. [printers] comment = All Printers path = /var/spool/samba guest only = Yes guest ok = Yes printable = Yes browseable = No

  Read the article

• help with xorg.conf: xrandr on one of two widescreen monitors; rhel5, kde, ATI Radeon X1300

  - by user35997

  Can anyone help with me configure my dual-screen monitors for rotation? I have xrandr 1.1. Have tried various approaches, nothing takes. I can't even get the xrandr options to show up in KDE's Display control panel. Thanks1 My lspci output: 03:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series] My current xorg.conf (works, minus screen rotation): # Xorg configuration created by system-config-display Section "ServerLayout" Identifier "Multihead layout" Screen 0 "aticonfig-Screen[0]" 0 0 InputDevice "Keyboard0" "CoreKeyboard" Option "Xinerama" "off" Option "Clone" "on" EndSection Section "Files" EndSection Section "Module" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection Section "Monitor" ### Comment all HorizSync and VertSync values to use DDC: Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Dell 2407WFP (Digital)" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 76.0 Option "dpms" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "Videocard0" Driver "vesa" EndSection Section "Device" Identifier "Videocard1" Driver "vesa" VendorName "Videocard Vendor" BoardName "ATI Technologies Inc RV516 [Radeon X1300/X1550 Series]" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "aticonfig-Device[0]" Driver "fglrx" Option "DesktopSetup" "horizontal" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection SubSection "Display" Viewport 0 0 Depth 16 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Videocard1" Monitor "Monitor1" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1920x1200" "1280x1024" "800x600" EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[0]" Device "aticonfig-Device[0]" Monitor "aticonfig-Monitor[0]" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1920x1200" "1280x1024" "800x600" EndSubSection EndSection

  Read the article

• pfSense + DDoS Protection

  - by Jeremy

  I run a gaming community on a colo with a 100Mbps port. I want to buy a very cheap 35 dollar server with the same 100Mbps port, and run pfSense to use as a hardware firewall. I'm dealing with a bunch of 14 year old kids that have access to botnets, so it can become a bit necessary to get something like this. My overall question, is using pfSense on a cheap identical datacenter/port speed server worth it to actually block DDoS attacks? A bit more into detail since I assume you will ask this, the attacks we receive are normally around 1Gbps. We currently run CentOS using CSF Firewall, and even when using a software firewall, we block 500Mbps UDP floods, or just generic attacks pretty easily. Thanks, - Necro

  Read the article

• droid cam makefile understanding and error

  - by nerorevenge

  I tried installing the droid cam on my fedora 19 (64 bit) . Link to the droid cam application is here and whenever I try to install it , the Makefile which is as follows is invoked obj-m := v4l2loopback-dc.o all: make -C /lib/modules/`uname -r`/build M=`pwd` test: gcc test.c -o test clean: make -C /lib/modules/`uname -r`/build M=`pwd` clean insmod: sudo insmod v4l2loopback-dc.ko width=320 height=240 rmmod: sudo rmmod v4l2loopback-dc.ko and here is the error -- INSTALL: Webcam parameters: '320' and '240' -- INSTALL: Building v4l2loopback-dc.ko make -C /lib/modules/`uname -r`/build M=`pwd` make: *** /lib/modules/3.9.5-301.fc19.x86_64/build: No such file or directory. Stop. make: *** [all] Error 2 -- INSTALL: v4l2loopback-dc.ko not built.. Failure build happens to be a symbolic link.I was wondering what exactly is the makefile trying to and why is it failing?

  Read the article

• Folder permissions when using /etc/skel and pam

  - by rothgar

  I have a Red Hat 5.8 server that is bound to active directory and users are authenticated via active directory when they log in via sftp. User home folders are created during login using /etc/pam.d/system-auth. The specific line that creates the home folder is session optional pam_mkhomedir.so skel=/etc/skel/ umask=0066 This correctly gives home folders 711 permissions so no one else can read their directories. The problem is, the pam_mkhomedir.so also modifies permissions on all folders/files inside the /etc/skel folder which I don't want. There is a public_html folder (for apache) which needs to have 755 permissions so users can create web pages. Is there a way for me to either a) stop pam_mkhomedir.so from recursively changing all the file permissions or b) create a script that creates the public_html folder after skel is copied and to set the correct permissions?

  Read the article

• How to solve "Broken Pipe" error when using awk with head

  - by Jon

  I'm getting broken pipe errors from a command that does something like: ls -tr1 /a/path | awk -F '\n' -vpath=/prepend/path/ '{print path$1}' | head -n 50 Essentially I want to list (with absolute path) the oldest X files in a directory. What seems to happen is that the output is correct (I get 50 file paths output) but that when head has output the 50 files it closes stdin causing awk to throw a broken pipe error as it is still outputting more rows.

  Read the article

• calling a different python interpreter from bash command line

  - by Dennis Daniels

  I have python 2.7 installed [user@localhost google_appengine]$ python Python 2.7 (r27:82500, Sep 16 2010, 18:03:06) [GCC 4.5.1 20100907 (Red Hat 4.5.1-3)] on linux2 Type "help", "copyright", "credits" or "license" for more information. I want to use the python 2.5.2 that is in this directory [user@localhost Downloads]$ ls |grep "Python-2*" Python-2.5.2 Python-2.5.2.tgz to run a python script in Khan Academy platform against a google app engine application sudo python sample_data.py -a ~/workspace/GAE/google_appengine/appcfg.py upload Currently, when running the last script 2.7 python complains a lot (Google App Engine runs on 2.5.2 mostly and 2.6 almost) I would like to do something like sudo python env set ~/Downloads/Python-2.5.2 sample_data.py -a ~/workspace/GAE/google_appengine/appcfg.py upload Is this possible? If yes, please point the way. If not, please suggest a way to call python2.5.2 WITHOUT having to uninstall python 2.7 many many thanks Dennis

  Read the article

• how do I create a new git repository with turnkey redmine?

  - by Ali Shafai

  I have downloaded the Turnkey's redmine VM and it's running finr (I can create new projects and wikis and document lists etc etc). only thing is I can't make it to use my new git repos. I found this link, but it didn't help. any help appreciated.

  Read the article

• Windows 8 won't boot after Boot Repair

  - by Rudolph Gottesheim

  I've got a Sony Vaio laptop. Until yesterday I had Windows 7 and Ubuntu 12.04 installed. Today I upgraded to Windows 8, which killed my OS selection screen. So I booted to Ubuntu 12.10 from a USB stick and ran Boot Repair. This recovered the GRUB screen and let me boot into my Ubuntu 12.04 installation, but now I can' boot Windows 8. When I select the option that booted Windows 7 before, it looks like it wants to start Windows 7 (sic) again (black screen, with the text "Windows is loading" or something), but then reboots the machine after a few seconds. I'm sure Boot Repair can fix this, but I know far too little about the whole booting thing to know the right settings for it. Here's my boot repair report thing.

  Read the article

• Bash wonkyness on Ubuntu versus RHEL

  - by d34dh0r53

  Fellow faulters, I'm playing around with a one liner that I've developed on a RHEL 5.4 box and I have it working perfectly: TOTAL_RAM=`free | grep Mem: | awk '{ print $2 }'`; \ ps axo rss,comm,pid | awk -v total_ram=$TOTAL_RAM \ '{ proc_list[$2] += $1; } END { for (proc in proc_list) \ { proc_pct = (proc_list[proc]/total_ram)*100; printf("%d\t%s\t%0.2f%\n", proc_list[proc],proc,proc_pct); }}' \ | sort -n | tail -n 10 Which outputs something like the following on my RHEL box: 3736 logmon 0.01% 4156 EvMgrC 0.01% 4692 hald 0.01% 5020 ntpd 0.02% 6252 sshd 0.02% 7784 cvd 0.02% 9224 snmpd 0.03% 13068 dsm_sa_datamgr3 0.04% 23320 dsm_om_connsvc3 0.07% 4249864 mysqld 12.90% However on my Ubuntu 9.04 slice I get this: awk: run time error: not enough arguments passed to printf("%d %s %0.2f% ") FILENAME="-" FNR=104 NR=104 33248 console-kit-dae 3.17 I think it has to be bash that is borking something, but I'm really not doing anything that should be that bash specific. The RHEL box is running: # yum info bash | grep -e Version -e Release Version : 3.2 Release : 24.el5 And the Ubuntu box: # apt-cache show bash | grep -e Version Version: 3.2-5ubuntu1 I haven't dug into this super deeply, and thought I'd ping my fellow johnnys to see if you've ever run across this before. /bow

  Read the article

• How can I force a MySQL table to become corrupted?

  - by Rory McCann

  I have written a simple Nagios plugin that calls mysqlcheck (which checks for corrupted tables) and will give a warning if any are corrupt. However none of my tables are corrupt now. So I'm not 100% sure that my plugin is working fine. I have a dev server that's not misson critical. How can I force one (or any) of the tables there to be corrupt so that I can test my nagios alert? For the record the server is Ubuntu Dapper and the mysql is version 5.0

  Read the article

• open mysql to any connection on ubuntu

  - by ThomasReggi

  I simply want to open up mysql to be accessible from any server ip. I have already commented out the bind-address in /etc/mysql/my.conf. I have already setup the user account within mysql. I have no clue whats stopping me from connecting. The more challenging I see this being the more I realize how much of a security risk it is, and I get that, I just want to be able to do it temporarily. I think that the iptables firewall is the last thing that is preventing me from achieving this, but sudo iptables -A INPUT -p tcp -m tcp --dport 3306 -j ACCEPT is seemingly doing nothing.

  Read the article

• Looking for the best ec2 setup for 3 sites totaling in 1.5 mil in traffic monthly

  - by john h.

  I am looking to consolidate our current aws setup of 2 Large ubuntu ec2 servers and 2 large RDS server for our 3 websites that have a total of about 1.5 million hits a month and increasing every month with the majority of traffic (1 mil) to one forum site in the group and the rest of traffic to an ecommerce site and a small wordpress site. So here is my question/thought? Would it be better for us to combine the two ec2 large servers to just one and same with the 2 RDS servers so we run all three sites off one large ec2 and one RDS. -or- Should we setup maybe 2-3 smaller ec2 servers load balenced and a single RDS. -or- Something completely different setup? One concern is that if one site crashes it takes with it the others. It happened in the past but I am pretty sure its because of the forum software and not the server setup. -john

  Read the article

< Previous Page | 318 319 320 321 322 323 324 325 326 327 328 329  | Next Page >