Search Results

Search found 13904 results on 557 pages for 'host on demand'.

Page 322/557 | < Previous Page | 318 319 320 321 322 323 324 325 326 327 328 329  | Next Page >

• Blocking RDP connections from secondary IP addresses

  - by user73995

  Hi, I have a webserver running Windows 2008 R2 with multiple IPs assigned to it. I want to be able to RDP to the box via the main IP assigned to the box but not from any of the secondary IPs (ie... the websites IPs). I assume if I had control of the Firewall I could shut off the RDP port to the secondary IPs but it's in a hosted environment and I don't have access to the firewall. I'll contact the host to see if that's available but was hoping there was a setting I could set on the machine itself to not resolve RDP requests from the additional IPs. Any advice?

  Read the article

• Debian apt dependency mismatch (libc6)

  - by Sean Gordon

  Earlier, I tried to install package via apt-get (cython), but it failed with the Errors were encountered while processing: message, and since then, apt is refusing to install anything. apt-get check output below: root@dix:~# apt-get check Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: libc6 : Depends: libc-bin (= 2.11.3-2) but 2.11.3-4 is installed libc6-dev : Depends: libc6 (= 2.11.3-4) but 2.11.3-2 is installed libc6-i386 : Depends: libc6 (= 2.11.3-4) but 2.11.3-2 is installed E: Unmet dependencies. Try using -f. Apt/aptitude don't seem to be able to fix this dependency issue, and I don't know what to do. Edit: Running apt-get -f install results in no change, and my sources are all squeeze. Running apt-get update then apt-get dist-upgrade show no change either. Edit 2: I went back to try this again in a new terminal and apt-get -f install gives this error: dpkg: error processing /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb (--unpack): subprocess new pre-installation script killed by signal (Aborted) configured to not write apport reports Errors were encountered while processing: /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Edit 3: Using apt-get clean first, then the previous commands, results in the first error again. Using apt-get -f dist-upgrade gives the below. Reading package lists... Building dependency tree... Reading state information... Correcting dependencies... Done The following packages will be upgraded: apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common at automake base-files bind9 bind9-doc bind9-host bind9utils debian-archive-keyring dnsutils dpkg-dev file host initscripts isc-dhcp-client isc-dhcp-common krb5-multidev libapr1 libbind9-60 libc6 libdns69 libdpkg-perl libexpat1 libexpat1-dev libgc1c2 libgssapi-krb5-2 libgssrpc4 libisc62 libisccc60 libisccfg62 libk5crypto3 libkadm5clnt-mit7 libkadm5srv-mit7 libkdb5-4 libkrb5-3 libkrb5-dev libkrb5support0 liblwres60 libmagic1 libmysqlclient16 libnss3-1d libssl-dev libssl0.9.8 libtiff4 libtiff4-dev libtiffxx0c2 libxi6 libxml2 linux-libc-dev lwresd mysql-client-5.1 mysql-common mysql-server mysql-server-5.1 mysql-server-core-5.1 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib openssh-client openssh-server openssl procps python python-crypto python-minimal sudo sysv-rc sysvinit sysvinit-utils tzdata tzdata-java 75 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 5 not fully installed or removed. Need to get 0 B/79.9 MB of archives. After this operation, 1,411 kB of additional disk space will be used. (Reading database ... 52241 files and directories currently installed.) Preparing to replace libc6 2.11.3-2 (using .../libc6_2.11.3-4_amd64.deb) ... *** stack smashing detected ***: /usr/bin/perl terminated ======= Backtrace: ========= /lib/libc.so.6(__fortify_fail+0x37)[0x7fdaad9b9f87] /lib/libc.so.6(__fortify_fail+0x0)[0x7fdaad9b9f50] /usr/lib/libperl.so.5.10(Perl_yylex+0x5896)[0x7fdaae343346] [0x8e83a0] ======= Memory map: ======== 00400000-00402000 r-xp 00000000 08:01 525338 /usr/bin/perl 00601000-00602000 rw-p 00001000 08:01 525338 /usr/bin/perl 00602000-0091f000 rw-p 00000000 00:00 0 [heap] 7fdaaca54000-7fdaaca6a000 r-xp 00000000 08:01 393818 /lib/libgcc_s.so.1 7fdaaca6a000-7fdaacc69000 ---p 00016000 08:01 393818 /lib/libgcc_s.so.1 7fdaacc69000-7fdaacc6a000 rw-p 00015000 08:01 393818 /lib/libgcc_s.so.1 7fdaacc6a000-7fdaacc6f000 r-xp 00000000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaacc6f000-7fdaace6e000 ---p 00005000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaace6e000-7fdaace6f000 rw-p 00004000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaace6f000-7fdaace79000 r-xp 00000000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaace79000-7fdaad078000 ---p 0000a000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaad078000-7fdaad079000 rw-p 00009000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaad079000-7fdaad07e000 r-xp 00000000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad07e000-7fdaad27d000 ---p 00005000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad27d000-7fdaad27e000 rw-p 00004000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad27e000-7fdaad299000 r-xp 00000000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad299000-7fdaad498000 ---p 0001b000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad498000-7fdaad49b000 rw-p 0001a000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad49b000-7fdaad49e000 r-xp 00000000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad49e000-7fdaad69e000 ---p 00003000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad69e000-7fdaad69f000 rw-p 00003000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad69f000-7fdaad6a7000 r-xp 00000000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad6a7000-7fdaad8a6000 ---p 00008000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a6000-7fdaad8a7000 r--p 00007000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a7000-7fdaad8a8000 rw-p 00008000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a8000-7fdaad8d6000 rw-p 00000000 00:00 0 7fdaad8d6000-7fdaada2f000 r-xp 00000000 08:01 393822 /lib/libc-2.11.3.so 7fdaada2f000-7fdaadc2e000 ---p 00159000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc2e000-7fdaadc32000 r--p 00158000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc32000-7fdaadc33000 rw-p 0015c000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc33000-7fdaadc38000 rw-p 00000000 00:00 0 7fdaadc38000-7fdaadc4f000 r-xp 00000000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaadc4f000-7fdaade4e000 ---p 00017000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade4e000-7fdaade4f000 r--p 00016000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade4f000-7fdaade50000 rw-p 00017000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade50000-7fdaade54000 rw-p 00000000 00:00 0 7fdaade54000-7fdaaded4000 r-xp 00000000 08:01 393826 /lib/libm-2.11.3.so 7fdaaded4000-7fdaae0d4000 ---p 00080000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d4000-7fdaae0d5000 r--p 00080000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d5000-7fdaae0d6000 rw-p 00081000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d6000-7fdaae0d8000 r-xp 00000000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae0d8000-7fdaae2d8000 ---p 00002000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2d8000-7fdaae2d9000 r--p 00002000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2d9000-7fdaae2da000 rw-p 00003000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2da000-7fdaae43f000 r-xp 00000000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae43f000-7fdaae63e000 ---p 00165000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae63e000-7fdaae647000 rw-p 00164000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae647000-7fdaae665000 r-xp 00000000 08:01 393819 /lib/ld-2.11.3.so 7fdaae854000-7fdaae859000 rw-p 00000000 00:00 0 7fdaae862000-7fdaae864000 rw-p 00000000 00:00 0 7fdaae864000-7fdaae865000 r--p 0001d000 08:01 393819 /lib/ld-2.11.3.so 7fdaae865000-7fdaae866000 rw-p 0001e000 08:01 393819 /lib/ld-2.11.3.so 7fdaae866000-7fdaae867000 rw-p 00000000 00:00 0 7fff9616d000-7fff9618e000 rw-p 00000000 00:00 0 [stack] 7fff961ff000-7fff96200000 r-xp 00000000 00:00 0 [vdso] ffffffffff600000-ffffffffff601000 r--p 00000000 00:00 0 [vsyscall] dpkg: error processing /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb (--unpack): subprocess new pre-installation script killed by signal (Aborted) Errors were encountered while processing: /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb

  Read the article

• Static NAT in AWS's Virtual Private Cloud (VPC)

  - by user1050797

  Currently in a VPC with a public and a private subnet, all internet bound traffic from the private subnet could be routed via an NAT instance. The NAT instance will port address translate the packet's source IP to use the NAT instance's elastic IP, so the public server can reply to this public address. This is a PAT mechanism. My question is there a way for me to do a static NAT on my NAT instance -- Using the same NAT instance to static NAT an unassociated but reserved elastic IP to a private subnet host. This NAT instance will behave like a physical firewall doing static nat'ing for a bunch of private ip's.

  Read the article

• Redirect example.com to www.example.com VPS & Apache2

  - by Thomas Buckley

  I have a VPS and a domain name registered with the provider. When I enter www.example.com my site is displayed correctly, but entering example.com does not work. I am able to ping www.example.com. I added the following line to my apache2 default vhosts file: ServerName example.com ServerAlias www.example.com But this did not work. The VPS is a Debian5 OS. Any ideas? Note: There is no option via a provided control panel to add this, it's a basic package I purchased I know this post answers it but there are no extra comments and I'd like to know if it's the best way: way to redirect page to www using virtual host configuration in sites-available for apache2? Thanks

  Read the article

• View httpd/lighttpd modules that are installed on shared hosting

  - by sdek

  I don't have access to the httpd.conf file on this shared host, but I wanted to see which modules are enabled/installed. Is there a (easy) way to find out without access to the httpd.conf file? For example, with PHP you can run a file that has phpinfo() in it to get the PHP info. Anything similar? The web server is lighttpd, which I understand is mostly compatible with apache httpd. (And yes, I am going to email the hosting support, but it sure would be nice to know for the future)

  Read the article

• KVM-Guests can't get past bridge - no internet connection

  - by tmn29a

  I'm running a backported KVM on a Debian Squeeze. ATM the KVM-Guest can't connect to the internet through the bridge I have set up. The guests can reach each other, the host but nothing outside. I can neither ping, nslookup or do anything to a remote address. The guest are configured to have a static IP. When I didn;t have the bridge but a virtual bridge (the KVM-default) the guest could connect fine. After setting up the bridge things broke, so I think the problem lies there. # The loopback network interface auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.XXX.XXX.84 netmask 255.255.255.192 network 10.XXX.XXX.64 gateway 10.XXX.XXX.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports eth0 eth1 address 172.xxx.xxx.65 broadcast 172.xxx.xxx.127 netmask 255.255.255.192 gateway 172.xxx.xxx.65 bridge_stp on bridge_maxwait 0 Thanks in advance for your help !

  Read the article

• Linksys Router/Tomato Firmware DNS issues

  - by jasonh

  I've got a WRT54GS that I've loaded the current version of Tomato onto. I entered static DHCP addresses in for the devices on my network, released and renewed the address on my desktop and tried to ping another computer. All I got was The request could not find host blah. Please check the name and try again. Now, I verified that my desktop and the target machine I'm trying to ping have both received their proper static DHCP lease and that their DNS server is the IP address of my router. What am I missing?

  Read the article

• Purpose of "computer" section in MySQL Cluster 7.2?

  - by dpk

  According to the cluster documentation, you can either define data nodes with: [ndbd] NodeId=n HostName=1.2.3.4 or [ndbd] NodeId=n ExecuteOnComputer=m [computer] Id=m HostName=1.2.3.4 I don't see a substantial difference between the two. The documentation has this to say: The [computer] section has no real significance other than serving as a way to avoid the need of defining host names for each node in the system. I'm stumped. If I have to define a hostname, what benefit is there to defining it in [computer] instead of [ndbd]?

  Read the article

• VMware Server Guest OS Random Shutdown

  - by radioactive21

  Anyone encounter a problem in which the Guest OS in VMware Server randomly shuts down? This has happened about once a month, where VMware Server just shuts down ALL guests OS. The host machine is fine, and you can log into the web management of VMware Server, it's just all guest OS get shutdown with no apparent reason. Even the logs say vmware guest os so and so was shut down, but no details why. This is not just one one machine, we have VMware server installed on three different PowerEdge servers and they all have encounter the same problem. We've tripped checked all settings and nothing is out of the ordinary.

  Read the article

• Wired and Wireless USB Network Adapter

  - by Evan M.

  Does anyone know if there are any USB network adapters out there that have both wired and wireless networking capability? Far-fetched, I know, but thought I'd ask. Background: Some of our users have locked down laptops that we also include unlocked virtual machines running on VMware Player. Sometimes the users have a need for network connectivity with their VMs where NAT and bridged networking from the host won't work. To supplement this, we want to supply them with adapters that they can use VMware USB pass through capabilities to provide appropriate connectivity. They will need both wired and wireless capability. Rather than carrying around 2 adapters, was hoping we could get a combination unit so that we can reduce it to 1. Thanks

  Read the article

• Copy/Paste (Clipboard like) functionality from a VNC desktop

  - by goldenmean

  I use TightVNC, RealVNC to access the Remote Linux(CentOS,Ubuntu) desktops by running a vncserver on the remote machine. When I connect to those servers from my Windows host: Can I use the Copy/Paste functionality on the VNC client desktop window. i.e. Copy some text on some terminal open inside the VNC client desktop window and paste it into some text file on my local windows machhines and vice-a-versa? I checked TightVNC options but did not see anything. Can it be done by a)Running vncserver on the remote machine with some options or b)By running some configuration on remote machine to enable this. How could I get it done? Also is this kind of Copy/Paste functionality possible in Microsoft Windows Remote Desktop connection/Terminal session protocol?

  Read the article

• Can not connect to telnet server

  - by BloodPhilia

  So, I can't use telnet to connect to any server but it works fine from a different computer. It just says it can't connect. I tried the following things: Disable firewall and AV protection. (Basically, there was no security feature left online) Telnet is set to "Trusted" in my AV protection. (Kaspersky Internet Security 2011) Using Putty to telnet, but apparently Putty's connection is also inhibited. (Says it can't connect to host) Disabling the telnet client in Control Panel and then re-enabling it. (Windows 7 Ultimate) hosts file is clean. Checked for nasties using MBAM and KIS 2011 as well as going though my HijackThis logs, nothing found. I can connect to the same machines/servers through the web browser, ping, tracert, etc. Only telnet seems to be blocked. Any other thoughts?

  Read the article

• Will being a VPN Client interrupt web pages hosted by IIS?

  - by f1gm3nt3d

  We have a dedicated server that is primarily used to host our website. I've been tasked with determining the feasibility of setting up a VPN connection from it to our Internal Network at our offices for a few ease of use purposes. My concern is that if I establish this VPN connection our Website will only be available internally and not to the internet in general. I'm concerned about this because in everything I read the fact is stated that by default all network traffic is routed over the VPN connection when it's established, is this also true for applications such as IIS that are listening for incoming connections? TL;DR Will having a VPN Client up and running cause a problem with server applications that may be listening on the NIC connected to the Internet due to changes that VPN makes in the routing tables?

  Read the article

• Why is this LTO4 Tape-drive not working

  - by Tim Haegele

  # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

  Read the article

• django url matching with Lighttpd fastcgi

  - by 7seb

  I have a problem with url. I can access the djando app home page ( localhost/djangotest/ ) but can't access the admin section ( localhost/djangotest/admin/ ). I can access it using the django server instead of lighttpd. Lighttp conf : fastcgi.server = ( "/djangotest/" => ( "main" => ( "host" => "127.0.0.1", "port" => 3033, "check-local" => "disable", ) ), ) url.rewrite-once = ( "^(/media.*)$" => "$1", "^/favicon\.ico$" => "/media/favicon.ico", "^/djangotest/[^?](.*)$" => "/djangotest/?$1", ) The django url.py is just : (i just uncommented the good lines) : from django.conf.urls.defaults import patterns, include, url from django.contrib import admin admin.autodiscover() urlpatterns = patterns('', url(r'^admin/', include(admin.site.urls)), ) I tried many things but without success ... (no need to link to https://docs.djangoproject.com/en/dev/howto/deployment/fastcgi/ ) lighttpd/1.4.28 Python 2.7.2+ Django 1.3.0

  Read the article

• Office 365 Powershell - Export user, license type, and company field to csv file

  - by ASGJim

  I need to be able to export user name or email address (doesn't matter which), company (from the company field under the organization tab in a user account of the exchange admin console), and license type (e.g. exchange online e1, exchange online kiosk etc...) I am able to export both values in two statements into two separate files but that doesn't do me much good. I can export the username and license type with the following: Get-MSOLUser | % { $user=$_; $_.Licenses | Select {$user.displayname},AccountSKuid } | Export-CSV "sample.csv" -NoTypeInformation And, I can get the company values with the following: Get-User | select company | Export-CSV sample.csv Someone on another forum suggested this - $index = @{} Get-User | foreach-object {$index.Add($_.userprincipalname,$_.company)} Get-MsolUser | ForEach-Object { write-host $_.userprincipalname, $index[$_.userprincipalname], $_.licenses.AccountSku.Skupartnumber} That seems like it should work but it doesn't display any license info in my powershell, it's just blank. Also I wouldn't know how to export that to a csv file. Any help would be appreciated. Thanks.

  Read the article

• Making an apache module work only for a particular sub domain

  - by Abhinav Upadhyay

  Hi everyone. I am not a regular webmaster , I am a student working on an internship project which is an Apache2 module, so my knowledge of Apache configuration is limited. I want to configure my module for a particular sub domain of the host server. Lets say I want my module to work only for onclick.localhost , then what are the directives required ? I want the module to be invoked only for the hosts/virtualhosts for which it has been configured explicitly. I know how to setup sub domains in Apache, so that's not a problem. Thanks.

  Read the article

• nginx symlinks permission denied / 403 Forbidden on Mac OSX

  - by Levi Roberts

  So I have an nginx server running on Mac OSX and I am trying to create a symlink in my nginx www directory from somewhere else. In the browser I get the wonderful 403 Forbidden error. I have also tried chmod'ing my life away for the past few hours. There doesn't seem to be anything on the stack about it. One thing concerns me is that I am not sure if symlinks are directly supported by ngninx on Mac. Trying to use disable_symlink directive results in: nginx: [emerg] unknown directive "disable_symlinks" in /usr/local/etc/nginx/nginx.conf:44` Some info about my setup: nginx -v : nginx version: nginx/1.4.2 To create the symlink I do the following: cd /Users/levi/www ln -s "/Users/levi/Desktop/.../client" "/Users/levi/www/client" The error in the log: [error] 11864#0: *7 open() "/Users/levi/www/client" failed (13: Permission denied), client: 127.0.0.1, server: _, request: "GET /client HTTP/1.1", host: "localhost" Any help is much appreciated. Let me know if there's any more information I can give you.

  Read the article

• Rails3 environment running very slow on Windows XP, Ubuntu 9.04, Ubuntu 9.10

  - by bergyman

  I've tried all three (granted the Ubuntu versions were via VirtualBox with XP as a host, but I gave the images all the available RAM my system has). Loading the rails environment is taking 30-60 seconds. rails console, rake test:units - anything that requires rails to load up. And not just on the first go - every time. I've even used autotest to see if it helps with execution time for unit tests, but it doesn't. Any time I change one test, it still takes 30 seconds to load them, and then about 4 seconds to execute. Has anyone else come across this issue? Has anyone figured out any way to fix this?

  Read the article

• how to escape “@” in the username when logging in through FTPES with curl?

  - by user62367

  $ curl -T "index.html" -k --ftp-ssl -u "[email protected]" MYDOMAIN.COM Enter host password for user '[email protected]': % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 0 57173 0 0 0 0 0 0 --:--:-- 0:00:01 --:--:-- 0 <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>405 Method Not Allowed</title> </head><body> <h1>Method Not Allowed</h1> <p>The requested method PUT is not allowed for the URL /index.html.</p> <hr> <address>Apache/2.2.16 Server at MYDOMAIN.COM Port 80</address> </body></html> 100 57480 100 307 100 57173 284 52902 0:00:01 0:00:01 --:--:-- 53633 can someone help me? Also posted on Stack Overflow

  Read the article

• Syslog - capturing event logs from Win2k boxes

  - by molecule

  Hi all, I asked this question in SuperUser without much luck and so I am posting it here to see if anyone can assist. We have a central syslog server and we want it to capture event log events from Windows hosts. We are specifically interested in logging service start/stop events. We installed "Eventlog to Syslog" on these windows hosts and all works well with XP hosts (Events come from Service Control Manager). However, we are having issues with Win2k hosts. For some reason, service start/stop events do not get logged in the Event Log for Win2k hosts. I got another friend from another company to test on a Win2k host and he does get start/stop events on them. I have searched around for local audit policies i need to enable but with not much luck. Anyone have any ideas? Thanks in advance.

  Read the article

• inconsistent ERRORLEVEL in a batch file

  - by Doron

  In a batch file, I have an inconsistent errorlevel behavior: The IP address 10.1.1.2 always replies. The following code always gives errorlevel 0 in one location (somewhere in the middle - exactly where i need it) inside the batch file. I copied only this snippet and placed it in the beginning and at the end of the batch file. In those locations, the result is always 1. Here is the code snippet: ping 10.1.1.2|Findstr /I /C:"timed out" /C:"host unreachable" echo %errorlevel% Any idea how to make it work also in the middle of the file? What am I doing wrong? I would hate to solve it with GOTOs(to the end of the file and back to where I need the result.)

  Read the article

• Wildcard SSL certificates, EV

  - by nachito

  I run a Magento e-commerce store with multiple subdomains for an affiliate program, plus a main store. Example, foo.example.com and bar.example.com are affiliates, www.example.com is my main store. They all share the same code and database and the same virtual host. Currently I have a wildcard certificate which works fine for everything. However, I was looking at EV certificates to increase customer confidence (which is not possible with wildcard certificates -- or so I'm told). What would be the simplest setup to have both an EV SSL Cert for the main store and a wildcard for the affiliate subdomains? Two virtual hosts? By the way, I'm running Litespeed as a webserver.

  Read the article

• SSH service will not start on fresh Cygwin 1.7.15 install

  - by Coder6841

  OS: Windows 7 x64 Cygwin: 1.7.15-1 OpenSSH: 6.0p1-1 I'm attempting to install an SSH server on Windows 7. The tutorial that I'm following to do this is here: http://www.howtogeek.com/howto/41560/how-to-get-ssh-command-line-access-to-windows-7-using-cygwin/ The issue is that upon executing the net start sshd command I get the following output:The CYGWIN sshd service is starting. The CYGWIN sshd service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534. Here is the full output of the setup: AdminUser@ThisComputer ~ $ ssh-host-config *** Info: Generating /etc/ssh_host_key *** Info: Generating /etc/ssh_host_rsa_key *** Info: Generating /etc/ssh_host_dsa_key *** Info: Generating /etc/ssh_host_ecdsa_key *** Info: Creating default /etc/ssh_config file *** Info: Creating default /etc/sshd_config file *** Info: Privilege separation is set to yes by default since OpenSSH 3.3. *** Info: However, this requires a non-privileged account called 'sshd'. *** Info: For more info on privilege separation read /usr/share/doc/openssh/README.privsep. *** Query: Should privilege separation be used? (yes/no) yes *** Info: Note that creating a new user requires that the current account have *** Info: Administrator privileges. Should this script attempt to create a *** Query: new local account 'sshd'? (yes/no) yes *** Info: Updating /etc/sshd_config file *** Query: Do you want to install sshd as a service? *** Query: (Say "no" if it is already installed as a service) (yes/no) yes *** Query: Enter the value of CYGWIN for the daemon: [] *** Info: On Windows Server 2003, Windows Vista, and above, the *** Info: SYSTEM account cannot setuid to other users -- a capability *** Info: sshd requires. You need to have or to create a privileged *** Info: account. This script will help you do so. *** Info: You appear to be running Windows XP 64bit, Windows 2003 Server, *** Info: or later. On these systems, it's not possible to use the LocalSystem *** Info: account for services that can change the user id without an *** Info: explicit password (such as passwordless logins [e.g. public key *** Info: authentication] via sshd). *** Info: If you want to enable that functionality, it's required to create *** Info: a new account with special privileges (unless a similar account *** Info: already exists). This account is then used to run these special *** Info: servers. *** Info: Note that creating a new user requires that the current account *** Info: have Administrator privileges itself. *** Info: No privileged account could be found. *** Info: This script plans to use 'cyg_server'. *** Info: 'cyg_server' will only be used by registered services. *** Query: Do you want to use a different name? (yes/no) no *** Query: Create new privileged user account 'cyg_server'? (yes/no) yes *** Info: Please enter a password for new user cyg_server. Please be sure *** Info: that this password matches the password rules given on your system. *** Info: Entering no password will exit the configuration. *** Query: Please enter the password: *** Query: Reenter: *** Info: User 'cyg_server' has been created with password '[CENSORED]'. *** Info: If you change the password, please remember also to change the *** Info: password for the installed services which use (or will soon use) *** Info: the 'cyg_server' account. *** Info: Also keep in mind that the user 'cyg_server' needs read permissions *** Info: on all users' relevant files for the services running as 'cyg_server'. *** Info: In particular, for the sshd server all users' .ssh/authorized_keys *** Info: files must have appropriate permissions to allow public key *** Info: authentication. (Re-)running ssh-user-config for each user will set *** Info: these permissions correctly. [Similar restrictions apply, for *** Info: instance, for .rhosts files if the rshd server is running, etc]. *** Info: The sshd service has been installed under the 'cyg_server' *** Info: account. To start the service now, call `net start sshd' or *** Info: `cygrunsrv -S sshd'. Otherwise, it will start automatically *** Info: after the next reboot. *** Info: Host configuration finished. Have fun! AdminUser@ThisComputer ~ $ net start sshd The CYGWIN sshd service is starting. The CYGWIN sshd service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534. Note that on the line *** Query: Enter the value of CYGWIN for the daemon: [] I haven't entered anything. Tutorials often say to use ntsec or ntsec tty here but those options are removed from the latest version of OpenSSH. I've tried using them anyway and the result is the same. The file /var/log/sshd.log is empty. If I try just running the command /usr/sbin/sshd I get the output /var/empty must be owned by root and not group or world-writable.. The /var/empty directory has the following permissions: drwxr-xr-x+ 1 cyg_server root 0 May 29 15:28 empty. Google searches on this error did not turn up any working fixes. One person seems to have solved it by using the command chown SYSTEM /var/empty but that did not fix it in my case.

  Read the article

• NLB 2 Windows Server 2003 Servers

  - by Paul Hinett

  I need to configure windows NLB on 2 dedicated servers I have. My main machine has been running for some time, with several domain names pointing to the servers primary IP address. Both servers have 2 NIC's installed, and both have several secondary public IP addresses available if needed? What IP address would I use for the cluster IP, does this IP need to be added to the IP list of both public NIC's ip address list? What IP addresses do I use for the host's dedicated IP? Please help, this is driving me nuts...i've taken down the server twice on accident today! Thank you in advance!

  Read the article

< Previous Page | 318 319 320 321 322 323 324 325 326 327 328 329  | Next Page >