Search Results

Search found 9082 results on 364 pages for 'quick launch'.

Page 326/364 | < Previous Page | 322 323 324 325 326 327 328 329 330 331 332 333  | Next Page >

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • Severe mysqldump performance degradation using Centos Linux, 8GB PAE and MySQL 5.0.77

    - by Duncan Harris
    We use MySQL 5.0.77 on CentOS 5.5 on VMWare: Linux dev.ic.soschildrensvillages.org.uk 2.6.18-194.11.4.el5PAE #1 SMP Tue Sep 21 05:48:23 EDT 2010 i686 i686 i386 GNU/Linux We have recently upgraded from 4GB RAM to 8GB. When we did this the time of our mysqldump overnight backup jumped from under 10 minutes to over 2 hours. It also caused unresponsiveness on our plone based web site due to database load. The dump is using the optimized mysqldump format and is spooled directly through a socket to another server. Any ideas on what we could do to fix gratefully appreciated. Would a MySQL upgrade help? Anything we can do to MySQL config? Anything we can do to Linux config? Or do we have to add another server or go to 64-bit? We ran a previous (non-virtual) server on 6GB PAE and didn't notice a similar issue. This was on same MySQL version, but Centos 4.4. Server config file: [mysqld] port=3307 socket=/tmp/mysql_live.sock wait_timeout=31536000 interactive_timeout=31536000 datadir=/var/mysql/live/data user=mysql max_connections = 200 max_allowed_packet = 64M table_cache = 2048 binlog_cache_size = 128K max_heap_table_size = 32M sort_buffer_size = 2M join_buffer_size = 2M lower_case_table_names = 1 innodb_data_file_path = ibdata1:10M:autoextend innodb_buffer_pool_size=1G innodb_log_file_size=300M innodb_log_buffer_size=8M innodb_flush_log_at_trx_commit=1 innodb_file_per_table [mysqldump] # Do not buffer the whole result set in memory before writing it to # file. Required for dumping very large tables quick max_allowed_packet = 64M [mysqld_safe] # Increase the amount of open files allowed per process. Warning: Make # sure you have set the global system limit high enough! The high value # is required for a large number of opened tables open-files-limit = 8192 Server variables: mysql> show variables; +---------------------------------+------------------------------------------------------------------+ | Variable_name | Value | +---------------------------------+------------------------------------------------------------------+ | auto_increment_increment | 1 | | auto_increment_offset | 1 | | automatic_sp_privileges | ON | | back_log | 50 | | basedir | /usr/local/mysql-5.0.77-linux-i686-glibc23/ | | binlog_cache_size | 131072 | | bulk_insert_buffer_size | 8388608 | | character_set_client | latin1 | | character_set_connection | latin1 | | character_set_database | latin1 | | character_set_filesystem | binary | | character_set_results | latin1 | | character_set_server | latin1 | | character_set_system | utf8 | | character_sets_dir | /usr/local/mysql-5.0.77-linux-i686-glibc23/share/mysql/charsets/ | | collation_connection | latin1_swedish_ci | | collation_database | latin1_swedish_ci | | collation_server | latin1_swedish_ci | | completion_type | 0 | | concurrent_insert | 1 | | connect_timeout | 10 | | datadir | /var/mysql/live/data/ | | date_format | %Y-%m-%d | | datetime_format | %Y-%m-%d %H:%i:%s | | default_week_format | 0 | | delay_key_write | ON | | delayed_insert_limit | 100 | | delayed_insert_timeout | 300 | | delayed_queue_size | 1000 | | div_precision_increment | 4 | | keep_files_on_create | OFF | | engine_condition_pushdown | OFF | | expire_logs_days | 0 | | flush | OFF | | flush_time | 0 | | ft_boolean_syntax | + -><()~*:""&| | | ft_max_word_len | 84 | | ft_min_word_len | 4 | | ft_query_expansion_limit | 20 | | ft_stopword_file | (built-in) | | group_concat_max_len | 1024 | | have_archive | YES | | have_bdb | NO | | have_blackhole_engine | YES | | have_compress | YES | | have_crypt | YES | | have_csv | YES | | have_dynamic_loading | YES | | have_example_engine | NO | | have_federated_engine | YES | | have_geometry | YES | | have_innodb | YES | | have_isam | NO | | have_merge_engine | YES | | have_ndbcluster | DISABLED | | have_openssl | DISABLED | | have_ssl | DISABLED | | have_query_cache | YES | | have_raid | NO | | have_rtree_keys | YES | | have_symlink | YES | | hostname | app.ic.soschildrensvillages.org.uk | | init_connect | | | init_file | | | init_slave | | | innodb_additional_mem_pool_size | 1048576 | | innodb_autoextend_increment | 8 | | innodb_buffer_pool_awe_mem_mb | 0 | | innodb_buffer_pool_size | 1073741824 | | innodb_checksums | ON | | innodb_commit_concurrency | 0 | | innodb_concurrency_tickets | 500 | | innodb_data_file_path | ibdata1:10M:autoextend | | innodb_data_home_dir | | | innodb_adaptive_hash_index | ON | | innodb_doublewrite | ON | | innodb_fast_shutdown | 1 | | innodb_file_io_threads | 4 | | innodb_file_per_table | ON | | innodb_flush_log_at_trx_commit | 1 | | innodb_flush_method | | | innodb_force_recovery | 0 | | innodb_lock_wait_timeout | 50 | | innodb_locks_unsafe_for_binlog | OFF | | innodb_log_arch_dir | | | innodb_log_archive | OFF | | innodb_log_buffer_size | 8388608 | | innodb_log_file_size | 314572800 | | innodb_log_files_in_group | 2 | | innodb_log_group_home_dir | ./ | | innodb_max_dirty_pages_pct | 90 | | innodb_max_purge_lag | 0 | | innodb_mirrored_log_groups | 1 | | innodb_open_files | 300 | | innodb_rollback_on_timeout | OFF | | innodb_support_xa | ON | | innodb_sync_spin_loops | 20 | | innodb_table_locks | ON | | innodb_thread_concurrency | 8 | | innodb_thread_sleep_delay | 10000 | | interactive_timeout | 31536000 | | join_buffer_size | 2097152 | | key_buffer_size | 8384512 | | key_cache_age_threshold | 300 | | key_cache_block_size | 1024 | | key_cache_division_limit | 100 | | language | /usr/local/mysql-5.0.77-linux-i686-glibc23/share/mysql/english/ | | large_files_support | ON | | large_page_size | 0 | | large_pages | OFF | | lc_time_names | en_US | | license | GPL | | local_infile | ON | | locked_in_memory | OFF | | log | OFF | | log_bin | OFF | | log_bin_trust_function_creators | OFF | | log_error | | | log_queries_not_using_indexes | OFF | | log_slave_updates | OFF | | log_slow_queries | OFF | | log_warnings | 1 | | long_query_time | 10 | | low_priority_updates | OFF | | lower_case_file_system | OFF | | lower_case_table_names | 1 | | max_allowed_packet | 67108864 | | max_binlog_cache_size | 4294963200 | | max_binlog_size | 1073741824 | | max_connect_errors | 10 | | max_connections | 200 | | max_delayed_threads | 20 | | max_error_count | 64 | | max_heap_table_size | 33554432 | | max_insert_delayed_threads | 20 | | max_join_size | 18446744073709551615 | | max_length_for_sort_data | 1024 | | max_prepared_stmt_count | 16382 | | max_relay_log_size | 0 | | max_seeks_for_key | 4294967295 | | max_sort_length | 1024 | | max_sp_recursion_depth | 0 | | max_tmp_tables | 32 | | max_user_connections | 0 | | max_write_lock_count | 4294967295 | | multi_range_count | 256 | | myisam_data_pointer_size | 6 | | myisam_max_sort_file_size | 2146435072 | | myisam_recover_options | OFF | | myisam_repair_threads | 1 | | myisam_sort_buffer_size | 8388608 | | myisam_stats_method | nulls_unequal | | ndb_autoincrement_prefetch_sz | 1 | | ndb_force_send | ON | | ndb_use_exact_count | ON | | ndb_use_transactions | ON | | ndb_cache_check_time | 0 | | ndb_connectstring | | | net_buffer_length | 16384 | | net_read_timeout | 30 | | net_retry_count | 10 | | net_write_timeout | 60 | | new | OFF | | old_passwords | OFF | | open_files_limit | 8192 | | optimizer_prune_level | 1 | | optimizer_search_depth | 62 | | pid_file | /var/mysql/live/mysqld.pid | | plugin_dir | | | port | 3307 | | preload_buffer_size | 32768 | | profiling | OFF | | profiling_history_size | 15 | | protocol_version | 10 | | query_alloc_block_size | 8192 | | query_cache_limit | 1048576 | | query_cache_min_res_unit | 4096 | | query_cache_size | 0 | | query_cache_type | ON | | query_cache_wlock_invalidate | OFF | | query_prealloc_size | 8192 | | range_alloc_block_size | 4096 | | read_buffer_size | 131072 | | read_only | OFF | | read_rnd_buffer_size | 262144 | | relay_log | | | relay_log_index | | | relay_log_info_file | relay-log.info | | relay_log_purge | ON | | relay_log_space_limit | 0 | | rpl_recovery_rank | 0 | | secure_auth | OFF | | secure_file_priv | | | server_id | 0 | | skip_external_locking | ON | | skip_networking | OFF | | skip_show_database | OFF | | slave_compressed_protocol | OFF | | slave_load_tmpdir | /tmp/ | | slave_net_timeout | 3600 | | slave_skip_errors | OFF | | slave_transaction_retries | 10 | | slow_launch_time | 2 | | socket | /tmp/mysql_live.sock | | sort_buffer_size | 2097152 | | sql_big_selects | ON | | sql_mode | | | sql_notes | ON | | sql_warnings | OFF | | ssl_ca | | | ssl_capath | | | ssl_cert | | | ssl_cipher | | | ssl_key | | | storage_engine | MyISAM | | sync_binlog | 0 | | sync_frm | ON | | system_time_zone | GMT | | table_cache | 2048 | | table_lock_wait_timeout | 50 | | table_type | MyISAM | | thread_cache_size | 0 | | thread_stack | 196608 | | time_format | %H:%i:%s | | time_zone | SYSTEM | | timed_mutexes | OFF | | tmp_table_size | 33554432 | | tmpdir | /tmp/ | | transaction_alloc_block_size | 8192 | | transaction_prealloc_size | 4096 | | tx_isolation | REPEATABLE-READ | | updatable_views_with_limit | YES | | version | 5.0.77 | | version_comment | MySQL Community Server (GPL) | | version_compile_machine | i686 | | version_compile_os | pc-linux-gnu | | wait_timeout | 31536000 | +---------------------------------+------------------------------------------------------------------+ 237 rows in set (0.00 sec)

    Read the article

  • SBS2003 to SBS2011 Migration - Installation Error

    - by Shawn Gradwell
    Microsoft Small Business Server 2003 to 2011 Migration. I followed the Migration Guide from Microsoft and the source server had no errors when running the various tests prior to the migration. I have completed the destination server setup using the Answer File and the server is up and running. It all looks good, I can access Exchange and AD and the only problem is the error message when you log in stating that the setup did not complete and to check the logs. Because all looks good I am continuing the migration to the destination server. I also have to state that this client does not use Sharepoint at all. Do I have to redo everything? Herewith the logs: [4992] 121016.225454.5905: Task: Starting Add User or Group access VSS registry. [4992] 121016.225454.7645: TaskManagement: In TaskScheduler.RunTasks(): The "ConfigureSharePointVSSRegistryTask" Task threw an Exception during the Run() call:System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated. at System.Security.Principal.NTAccount.Translate(IdentityReferenceCollection sourceAccounts, Type targetType, Boolean forceSuccess) at System.Security.Principal.NTAccount.Translate(Type targetType) at System.Security.AccessControl.CommonObjectSecurity.ModifyAccess(AccessControlModification modification, AccessRule rule, Boolean& modified) at System.Security.AccessControl.CommonObjectSecurity.AddAccessRule(AccessRule rule) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.AddUsersToAccessRegistry(List`1 names) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.Run(ITaskDataLink dl) at Microsoft.WindowsServerSolutions.TaskManagement.Data.Task.Run(ITaskDataLink dataLink) at Microsoft.WindowsServerSolutions.TaskManagement.TaskScheduler.RunTasks(String taskListId, String stateFileName) [4992] 121016.225454.7655: Setup: An error was encountered on the TME thread: System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated. at System.Security.Principal.NTAccount.Translate(IdentityReferenceCollection sourceAccounts, Type targetType, Boolean forceSuccess) at System.Security.Principal.NTAccount.Translate(Type targetType) at System.Security.AccessControl.CommonObjectSecurity.ModifyAccess(AccessControlModification modification, AccessRule rule, Boolean& modified) at System.Security.AccessControl.CommonObjectSecurity.AddAccessRule(AccessRule rule) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.AddUsersToAccessRegistry(List`1 names) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.Run(ITaskDataLink dl) at Microsoft.WindowsServerSolutions.TaskManagement.Data.Task.Run(ITaskDataLink dataLink) at Microsoft.WindowsServerSolutions.TaskManagement.TaskScheduler.RunTasks(String taskListId, String stateFileName) at Microsoft.WindowsServerSolutions.Setup.SBSSetup.ProgressPagePresenter._RunTasks(Object sender, DoWorkEventArgs e) [4956] 121016.225455.0685: Setup: _UnhandledExceptionHandler: Setup encountered an error: System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.Reflection.TargetInvocationException: The TME thread failed (see the inner exception). ---> System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated. at System.Security.Principal.NTAccount.Translate(IdentityReferenceCollection sourceAccounts, Type targetType, Boolean forceSuccess) at System.Security.Principal.NTAccount.Translate(Type targetType) at System.Security.AccessControl.CommonObjectSecurity.ModifyAccess(AccessControlModification modification, AccessRule rule, Boolean& modified) at System.Security.AccessControl.CommonObjectSecurity.AddAccessRule(AccessRule rule) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.AddUsersToAccessRegistry(List`1 names) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.Run(ITaskDataLink dl) at Microsoft.WindowsServerSolutions.TaskManagement.Data.Task.Run(ITaskDataLink dataLink) at Microsoft.WindowsServerSolutions.TaskManagement.TaskScheduler.RunTasks(String taskListId, String stateFileName) at Microsoft.WindowsServerSolutions.Setup.SBSSetup.ProgressPagePresenter._RunTasks(Object sender, DoWorkEventArgs e) at System.ComponentModel.BackgroundWorker.WorkerThreadStart(Object argument) --- End of inner exception stack trace --- at Microsoft.WindowsServerSolutions.Setup.SBSSetup.ProgressPagePresenter.TasksCompleted(Object sender, RunWorkerCompletedEventArgs e) --- End of inner exception stack trace --- at System.RuntimeMethodHandle._InvokeMethodFast(IRuntimeMethodInfo method, Object target, Object[] arguments, SignatureStruct& sig, MethodAttributes methodAttributes, RuntimeType typeOwner) at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture, Boolean skipVisibilityChecks) at System.Delegate.DynamicInvokeImpl(Object[] args) at System.Windows.Forms.Control.InvokeMarshaledCallbackDo(ThreadMethodEntry tme) at System.Windows.Forms.Control.InvokeMarshaledCallbackHelper(Object obj) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Windows.Forms.Control.InvokeMarshaledCallback(ThreadMethodEntry tme) at System.Windows.Forms.Control.InvokeMarshaledCallbacks() at System.Windows.Forms.Control.WndProc(Message& m) at System.Windows.Forms.NativeWindow.DebuggableCallback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam) at System.Windows.Forms.UnsafeNativeMethods.DispatchMessageW(MSG& msg) at System.Windows.Forms.Application.ComponentManager.System.Windows.Forms.UnsafeNativeMethods.IMsoComponentManager.FPushMessageLoop(IntPtr dwComponentID, Int32 reason, Int32 pvLoopData) at System.Windows.Forms.Application.ThreadContext.RunMessageLoopInner(Int32 reason, ApplicationContext context) at System.Windows.Forms.Application.ThreadContext.RunMessageLoop(Int32 reason, ApplicationContext context) at Microsoft.WindowsServerSolutions.Common.Wizards.Framework.WizardChainEngine.Launch() at Microsoft.WindowsServerSolutions.Setup.SBSSetup.MainClass._LaunchWizard() at Microsoft.WindowsServerSolutions.Setup.SBSSetup.MainClass.RealMain(String[] args) at Microsoft.WindowsServerSolutions.Setup.SBSSetup.MainClass.Main(String[] args) [4956] 121016.225455.0865: Setup: Removed the password. [4956] 121016.225455.0905: Setup: Deleting scheduled task at path Microsoft\Windows\Windows Small Business Server 2011 Standard with name Setup [4956] 121016.225455.8055: Setup: Removed SBSSetup from the RunOnce.

    Read the article

  • Issues configuring Exchange 2010 as well as SSL problems.

    - by Eric Smith
    Possibly-Relevant Background Info: I've recently moved up from icky shared hosting to a glorious, Remote Desktop-administrated VPS server running Windows Server 2008 R2. Even though I'm only 21 now and a computer science major, I've tried to play with every Windows Server release since '03, just to learn new things. What usually happens is inevitably I'll do something wrong and pretty much ruin the install. You're dealing with an amateur here :) Through the past few months of working with my new server, I've mastered DNS, IIS, got Team Foundation Server running (yay!), and can install all of the other basics like SQL Server and Active Directory. The Problem: Now, these last few weeks I've been trying to install Exchange Server 2010 (SP1). To make a long story short, it took me several attempts, and I even had to get my server wiped just so I could start fresh since Exchange decided uninstalling properly was for sissies (cost me $20, bah). Today, at long last, I got Exchange mostly working. There were two main problems left, however, that left me unsatisfied: Exchange installed itself and all of its child sites into Default Web Site. I wanted to access Exchange via mail.domain.com, but instead everything was configured to domain.com. My limited server admin knowledge was not enough to configure IIS or Exchange to move itself over to the website I had set up for it, appropriately titled 'mail.domain.com', which I had bound to a dedicated IP address (I was told this was necessary, but he may have been wrong). I have two SSL certificates: one for my main domain and one for my mail subdomain. For whatever reason, I had issues geting Exchange to use my mail certificate, even though I had assigned the proper roles in the MMC. I did, at one point, get it to work (or mostly work, anyways. Frankly, my memory of today is clouded by intense frustration). Additionally, I was confused which type of SSL certificate I should be using for Exchange. My SSL provider, GoDaddy, allows me to request a new certificate whenever, so I can use either the certificate request provided by IIS or the more complicated and specific request you can create with Exchange. Which type should I be using, the IIS or Exchange certificate? If I must use the Exchange certificate, will that 1) cause issues when I bind that certificate to my mail.domain.com subdomain or 2) is that an unnecessary step? The SSL Certificate Strikes Back When I thought I had the proper SSL certificate assigned for those brief, sweet moments, Google Chrome reported the correct mail.domain.com certificate when browsing https://mail.domain.com. However, Outlook 2010 threw up an error when trying to configure my email account claiming that the certificate didn't match the domain of "mail.domain.com". Is this an issue that will be resolved by problem #2 or is it a separate one entirely? Apologies for the massive wall of text, but I wanted to provide as much info as I possibly could. Exchange is the last thing I'd like installed on my server, and naturally it's turning out to be the hardest. Thanks for any info at all. Even a point in a vague direction would be a huge help at this point. Thanks! -Eric P.S.: The reason I keep ruining my install is that when I attempt to uninstall Exchange, something invariably goes wrong. The last time the uninstaller complained that there was still a mailbox active and it couldn't proceed until I deleted it. ... The only mailbox left was the Administrator account, the built-in one I couldn't delete. So I attempted to manually uninstall it following several guides online only to now be stuck unable to launch the installer and have to get my system wiped AGAIN for the second time today ($40 down the drain, bah!). I do not understand at all why "uninstall" just can't mean "hey, you, delete everything and go away". There's not even a force uninstall option, only a "recover system" option that just fails to fix anything and makes it so I can't even use the GUI uninstaller. </rant>

    Read the article

  • OpenVPN on Tomato and Vista - can't see my network

    - by Ian
    I followed the instructions here (http://todayguesswhat.blogspot.ca/2011/03/quick-simple-vpn-setup-guide-using.html) to set up a TCP connection to OpenVPN on my Tomato router. Used TCP because the place I usually surf at seems to have the other ports blocked. My Vista laptop is able to connect to the router but I don't appear to be getting an IP address. I'm able to access my router's admin page, but I can't see the network at home. When I browse to Whatsmyip I see my home IP. Here are the results of route print -4 when I'm just connect to the library and when I've fired up the VP connection as well: Library only: =========================================================================== Interface List 22 ...00 ff c4 a0 e7 5c ...... TAP-Win32 Adapter V9 15 ...00 23 4e 20 b3 64 ...... Atheros AR9281 Wireless Network Adapter 10 ...00 23 8b 39 ec 71 ...... Marvell Yukon 88E8040T PCI-E Fast Ethernet Controller 1 ........................... Software Loopback Interface 1 11 ...00 00 00 00 00 00 00 e0 isatap.{834A8A0A-5E2C-47D0-9673-7965DE8B5470} 14 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 17 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 20 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 18 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 19 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 23 ...00 00 00 00 00 00 00 e0 isatap.{C4A0E75C-765E-4F7D-A55C-77945779816A} 34 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Library and TCP OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.116 30 0.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 24.212.205.68 255.255.255.255 10.1.29.1 10.1.29.117 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 192.168.1.0 255.255.255.0 On-link 192.168.1.116 286 192.168.1.116 255.255.255.255 On-link 192.168.1.116 286 192.168.1.255 255.255.255.255 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.116 286 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Thanks for any advice. I looked at one of the answers but I'm not sure if it applied to me as it said that 10...* was the vpn connection, but I appear to have 10...* when I connect just to the library.

    Read the article

  • Cannot open simple script application on mac

    - by streetpc
    Mac OS X 10.6 I created a very simple app, which is only a wrapper of a shell script (so that I can select this script in application selectors, like startup apps). I try to launch it and yesterday it worked, but today I changed the executable script's content and name (with something that perfeclty works in a shell script launched in the Terminal) and it will only display a Finder-iconed dialog saying Cannot open the application because it is not supported on this kind of Mac. I restored the previous script (content/name) but I still get the error! Same when re-bundling the app from scratch, or completely changing the bundle identifier… If I try to open it in the Terminal using open My.app, I get The application cannot be opened because it has an incorrect executable format. But when I executes directly the Contents/MacOS/Script, it allways works (iwth both contents). Also, it is displayed with correct icon and meta-information in the Finder (so I guess the Info.plist is understood). The app's file tree is: Contents/ Info.plist MacOS/ Script (executable bit set, works when launched directly) PkgInfo Resources/ AppIcon.icns Here is the Info.plist content: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>CFBundleExecutable</key> <string>Script</string> <key>CFBundleIconFile</key> <string>AppIcon</string> <key>CFBundleIdentifier</key> <string>asdf.ScriptApp</string> <key>CFBundleInfoDictionaryVersion</key> <string>6.0</string> <key>CFBundleName</key> <string>My script</string> <key>CFBundlePackageType</key> <string>APPL</string> <key>CFBundleShortVersionString</key> <string>1.0</string> <key>CFBundleSignature</key> <string>????</string> <key>CFBundleVersion</key> <string>1</string> <key>LSMinimumSystemVersion</key> <string>10.4</string> </dict> </plist> And the PkgInfo file only contains APPL????. I tested the Script with a simple echo "ok" and echo "ok" >/tmp/test (plus #!/bin/sh header). So my questions are: Is there some kind of validity caching for applications ? based on what ? how do I flush it ? Where does this message come from ? I tried to google it but all I get is a page talking about 32/64 bits Java…

    Read the article

  • CPU/JVM/JBoss 7 slows down over time

    - by lukas
    I'm experiencing performance slow down on JBoss 7.1.1 Final. I wrote simple program that demostrates this behavior. I generate an array of 100,000 of random integers and run bubble sort on it. @Model public class PerformanceTest { public void proceed() { long now = System.currentTimeMillis(); int[] arr = new int[100000]; for(int i = 0; i < arr.length; i++) { arr[i] = (int) (Math.random() * 200000); } long now2 = System.currentTimeMillis(); System.out.println((now2 - now) + "ms took to generate array"); now = System.currentTimeMillis(); bubbleSort(arr); now2 = System.currentTimeMillis(); System.out.println((now2 - now) + "ms took to bubblesort array"); } public void bubbleSort(int[] arr) { boolean swapped = true; int j = 0; int tmp; while (swapped) { swapped = false; j++; for (int i = 0; i < arr.length - j; i++) { if (arr[i] > arr[i + 1]) { tmp = arr[i]; arr[i] = arr[i + 1]; arr[i + 1] = tmp; swapped = true; } } } } } Just after I start the server, it takes approximately 22 seconds to run this code. After few days of JBoss 7.1.1. running, it takes 330 sec to run this code. In both cases, I launch the code when the CPU utilization is very low (say, 1%). Any ideas why? I run the server with following arguments: -Xms1280m -Xmx2048m -XX:MaxPermSize=2048m -Djava.net.preferIPv4Stack=true -Dorg.jboss.resolver.warning=true -Dsun.rmi.dgc.client.gcInterval=3600000 -Dsun.rmi.dgc.server.gcInterval=3600000 -Djboss.modules.system.pkgs=org.jboss.byteman -Djava.awt.headless=true -Duser.timezone=UTC -Djboss.server.default.config=standalone-full.xml -Xrunjdwp:transport=dt_socket,address=8787,server=y,suspend=n I'm running it on Linux 2.6.32-279.11.1.el6.x86_64 with java version "1.7.0_07". It's within J2EE applicaiton. I use CDI so I have a button on JSF page that will call method "proceed" on @RequestScoped component PerformanceTest. I deploy this as separate war file and even if I undeploy other applications, it doesn't change the performance. It's a virtual machine that is sharing CPUs with another machine but that one doesn't consume anything. Here's yet another observation: when the server is after fresh start and I run the bubble sort, It utilizes 100% of one processor core. It never switches to another core or drops utilization below 95%. However after some time the server is running and I'm experiencing the performance problems, the method above is utilizing CPU core usually 100%, however I just found out from htop that this task is being switched very often to other cores. That is, at the beginning it's running on core #1, after say 2 seconds it's running on #5 then after say 2 seconds #8 etc. Furthermore, the utilization is not kept at 100% at the core but sometimes drops to 80% or even lower. For the server after fresh start, even though If I simulate a load, it never switches the task to another core.

    Read the article

  • How do I reset/update my BIOS for Optiplex GX280?

    - by Sam Langlhey
    So far this has been a nightmare for me, which has been frustrating me constantly. I am using Dell Optiplex GX280 with Windows XP home edition, which is running a BIOS version A04. Recently, i've rebooted the pc to find out that its not booting. It will get to the Windows boot up screen with the progress bar but only to restart to the same process again, over and over. Frustrated that I am, i've inserted the Windows recovery CD to at least either repair of reinstall the operating system to find out that was not possible. I hit F8 to have the boot options, each of the boot option that I've selected gave me an error saying: "Selected boot device is not available." Right after that, I went to the BIOS setting and did a diagnostic test, which recognized all the Boot devices onboard. Now, I cannot even repair of reinstall Windows XP, because the system is not booting from none of the boot devices. The surprise is when I removed the hard-drive from the computer and loaded it on into another computer successfully; that's right, there is nothing wrong with the hard drive. After that I was totally puzzled. I found a few pointers online saying that the BIOS start-up block might be corrupted itself and I might need to flash/update the BIOS. I found the detailed instruction on how to create a Boot up disk by downloading the BIOS firmware from the manufacture's website. I did exactly as instructed below: Download the latest version or your choose version of BIOS file for your computer or motherboard from the manufacturer’s support site. Rename the downloaded file to AMIBOOT.ROM. Copy the file to a floppy disk. Insert the floppy disk to the floppy drive. Turn on the system. After I did that and powered on the PC to boot from the floppy drive, it gave me this error message: "Non-System Disk or Disk Error. Replace and Strike any key when ready." I did all that, and I kept on pressing [Ctrl]+[Home] to force it, but it did not did any satisfying result. Desperate as I am, my next attempt is to try the instruction below. Since I want to be ready, in the event it does not work, do you have any solution that you can provide? Please keep in mind that I cannot boot from any of the devices at this moment. My only hope now is to come on with a solution that will work through the Floppy drive, since that's the only drive that affected. Thank you very much for your advice and support in advance. To create a Windows startup disk, insert a floppy disk into the drive of a similarly configured, working Windows XP system, launch My Computer, right-click the floppy disk icon, and select the Format command from the context menu. When you see the Format dialog box, leave all the default settings as they are and click the Start button. Once the format operation is complete, close the Format dialog box to return to My Computer, double-click the drive C icon to access the root directory, and copy the following three files to the floppy disk: Boot.ini NTLDR Ntdetect.com

    Read the article

  • Using different SSDs types (not only SATA based) as system drive

    - by Hubert Kario
    Currently I have a Thinkpad X61s and want to make it both a bit faster and a bit more power efficient. For that reason I thought that adding SSD drive would make most sense. Unfortunately, because of financial reasons, buying SSD of over 200GB capacity is out of reach for me (not only it would be worth more than the rest of the laptop, but also I currently have a 500GB drive in it, so even such a drive would be kind of a downgrade for me). During preliminary testing with a cheap Transcend 4GB Class 6 (14MiB/s streaming, 9MiB/s random read) card I experienced boot times to be reduced by half so putting the OS only on it would already would be an improvement. Unfortunately, my system now is about 11GiB in size so anything less than 16GB would be constraining. In this laptop I can connect additional drives on at least 5 different ways: using SATA-ATA converter caddy in the X6 Ultrabase using internal mini PCIe slot using integrated SDHC slot using CardBus (a.k.a PCMCIA or PC Card) slot using USB Thankfully, because I use only Linux on this PC the bootability of them is irrelevant as I can put the /boot partition on internal HDD and / on any of the above mentioned Flash memories (as I already did for the SDHC test). From what I was able to research and from my own experience those options come with rather big downsides or other problems: SATA-ATA caddy It has three downsides: I have to carry the Ultrabse with me at all times (it's not really inconvenient, but those grams do add) and couldn't disconnect it when I want to disconnect the battery It makes the bay unusable for the optical drive and occasional quick access to other hard drives the only caddies I could buy have rather flaky controllers in them so putting my OS on it would hamper its stability Internal mini PCIe slot This would be an ideal solution, if only I could find real PCIe SSDs, not only devices that could talk only SATA or ATA over PCIe mechanical connection (the ones used in Dell Mini or Asus EEE). Theoretically Samsung did release such devices but I couldn't find them in retail anywhere. Integrated SDHC slot It's a nice solution with a single drawback: the fastest 16GB SDHC card on the market can only do around 35MiB/s read and 15MiB/s write while still costing like a normal 40GB SATA SSD that's 10 times faster. Not really cost-effective. CardBus (a.k.a PCMCIA or PC Card) slot Those cards are much faster than the SDHC option (there are ones that can do well over 50MiB/s read in benchmarks) and from what I could find the PCMCIA controller in my laptop does support UDMA so it should be able to deliver comparable speeds. They still cost similarly to SD cards but at least they provide streaming performance comparable to my current HDD. USB That's the worst option. Not only is it limited to 20-30MiB/s by the interface itself the drive would stick out of the laptop so it's a big no no. The question As such I think that going the "CF in a CardBus adapter" route will be the best option. My question is: did anyone try using CF cards in CardBus adapters as system drives with Linux on Thinkpad laptops? Laptops in general? What was the real-world performance? I don't have any CF cards so I can't check how well does it work with suspend/resume, or whatever it's easy to make it work in initramfs (I'm using ArchLinux and SD card was trivial — add 3 modules in single config line and rebuilding initramfs) so any tips/gotchas on this are welcome as well.

    Read the article

  • Why does my computer run slowly and freeze sometimes?

    - by Brae
    EDIT I disabled sound in the BIOS, rebooted and it hung. I removed the (previously) faulty HDD, rebooted and it hung. I have managed to get my Realtek audio manager open again after its mysterious disappearance. Subsequently my microphone is now working again, to fix it I had to uninstall audio drivers, disable audio in BIOS, install audio drivers, enable audio in BIOS. Access via network (with faulty HDD in) seems to not be triggering hangs at the moment. I think with the sound problem fixed it might play a little nicer, but I think its still going to hang. If it does, then I'm fairly sure its been narrowed down to the mobo. EDIT Pretty convinced my motherboard is the culprit, because nothing else seems to have any obvious problems (bar the hard drive, which the PC still hangs without it being plugged in) So thank you all for helping, once I get more rep ill up a few of the answers. My PC is doing some weird things... Sometimes when I open up a program, lets say Adobe Photoshop, it will load everything normally, nice and quick no problems and I can use it fine. Other times its a little odd, and it loads the program as if it's only using half of the CPU. It's pretty obvious when it does it, normally the loading screen skims past, but when it does this weird load you see it slowly tick though each thing, and the program itself becomes incredibly slow. Even Google Chrome does it sometimes. Yet when I exit and reopen the program without doing anything else, it typically opens fine without lagging. I think this problem is probably a symptom of something bigger, because of other problems I'm having. Random hangs; no matter what I have open or what I'm doing. My PC will sort of freeze up for a few seconds. If music is playing it will either loop the last second or two, or it will buzz. This only lasts for a few seconds then it returns to normal without having to restart. During this time all programs lock up and freeze, and the mouse and keyboard are useless. I am also having a weird issue with my audio jacks, without touching my PC at all, sometimes I will see a popup saying that I have unplugged something or plugged something in, neither of which has actually happened. Pretty sure this is cause by the motherboard. I recently had a 'Pink Screen of Death' (yes pink) which pointed to my audio drivers. The lockups seem to happen with some consistency when someone is accessing my shared files via my home LAN. Which leads me to believe either one of my hard drives is acting up or more likely the controller. One of my drives had a bit of a crash before, I used Spinrite and managed to recover my stuff and now the drive appears to be working okay. This is possibly adding to the problems. My best guess is something has gone wrong with my motherboard, possibly a power issue or a chip has died, I really don't know. So what I would like to know is: Have I have missed some obvious diagnostic to help figure out what it is, or should I just bite the bullet and assume its my motherboard acting up and buy a new system? dxdiag[64-bit] - http://pastebin.com/G30kb2TL PSOD (minidump) - http://pastebin.com/aZsv0H56 HWiNFO64 (system info / specs) - http://pastebin.com/X6h3K8g6

    Read the article

  • Windows 7 inbuilt and 3rd party (de)fragmentation related queries

    - by Karan
    I have a pretty good idea of how files end up getting fragmented. That said, I just copied ~3,200 files of varying sizes (from a few KB to ~20GB) from an external USB HDD to an internal, freshly formatted (under Windows 7 x64), NTFS, 2TB, 5400RPM, WD, SATA, non-system (i.e. secondary) drive, filling it up 57%. Since it should have been very much possible for each file to have been stored in one contiguous block, I expected the drive to be fragmented not more than 1-2% at most after this rather lengthy exercise (unfortunately this older machine doesn't support USB 3.0). Windows 7's inbuilt defrag utility told me after a quick analysis that the drive was fragmented only 1% or so, which dovetailed neatly with my expectations. However, just out of curiosity I downloaded and ran the latest portable x64 version of Piriform's Defraggler, and was shocked to see the drive being reported as being ~85% fragmented! The portable version of Auslogics Disk Defrag also agreed with Defraggler, and both clearly expected to grind away for ~10 hours to completely defragment the drive. 1) How in blazes could the inbuilt and 3rd party defrag utils disagree so badly? I mean, 10-20% variance is probably understandable, but 1% and 85% are miles apart! This Engineering Windows 7 blog post states: In Windows XP, any file that is split into more than one piece is considered fragmented. Not so in Windows Vista if the fragments are large enough – the defragmentation algorithm was changed (from Windows XP) to ignore pieces of a file that are larger than 64MB. As a result, defrag in XP and defrag in Vista will report different amounts of fragmentation on a volume. ... [Please read the entire post so the quote is not taken out of context.] Could it simply be that the 3rd party defrag utils ignore this post-XP change and continue to use analysis algos similar to those XP used? 2) Assuming that the 3rd party utils aren't lying about the real extent of fragmentation (which Windows is downplaying post-XP), how could the files have even got fragmented so badly given they were just copied over afresh to an empty drive? 3) If vastly differing analysis algos explain the yawning gap, which do I believe? I'm no defrag fanatic for sure, but 85% is enough to make me seriously consider spending 10 hours defragging this drive. On the other hand, 1% reported by Windows' own defragger clearly implies that there is no cause for concern and defragging would actually have negative consequences (as per the post). Is Windows' assumption valid and should I just let it be, or will there be any noticeable performance gains after running one of the 3rd party utils for 10 hours straight? 4) I see that out of the box Windows 7 defrag is scheduled to run weekly. Does anyone know whether it defrags every single time, or only if its analysis reveals a fragmentation percentage over a set threshold? If the latter, what is this threshold and can it be changed, maybe via a Registry edit? Thanks for reading through (my first query on this wonderful site!) and for any helpful replies. Also, if you're answering question #3, please keep in mind that any speed increases post defragging with 3rd party utils vis-à-vis Windows' inbuilt program should not include pre-Vista (preferably pre-Win7) examples. Further, examples of programs that made your system boot faster won't help in this case, since this is a non-system drive (although one that'll still be used daily).

    Read the article

  • What's the difference between find and findstr commands in Windows?

    - by Prashant Bhate
    In Windows, what are the differences between find and findstr commands? Both seems to search text in files: find c:\>find /? Searches for a text string in a file or files. FIND [/V] [/C] [/N] [/I] [/OFF[LINE]] "string" [[drive:][path]filename[ ...]] /V Displays all lines NOT containing the specified string. /C Displays only the count of lines containing the string. /N Displays line numbers with the displayed lines. /I Ignores the case of characters when searching for the string. /OFF[LINE] Do not skip files with offline attribute set. "string" Specifies the text string to find. [drive:][path]filename Specifies a file or files to search. If a path is not specified, FIND searches the text typed at the prompt or piped from another command. findstr c:\>findstr /? Searches for strings in files. FINDSTR [/B] [/E] [/L] [/R] [/S] [/I] [/X] [/V] [/N] [/M] [/O] [/P] [/F:file] [/C:string] [/G:file] [/D:dir list] [/A:color attributes] [/OFF[LINE]] strings [[drive:][path]filename[ ...]] /B Matches pattern if at the beginning of a line. /E Matches pattern if at the end of a line. /L Uses search strings literally. /R Uses search strings as regular expressions. /S Searches for matching files in the current directory and all subdirectories. /I Specifies that the search is not to be case-sensitive. /X Prints lines that match exactly. /V Prints only lines that do not contain a match. /N Prints the line number before each line that matches. /M Prints only the filename if a file contains a match. /O Prints character offset before each matching line. /P Skip files with non-printable characters. /OFF[LINE] Do not skip files with offline attribute set. /A:attr Specifies color attribute with two hex digits. See "color /?" /F:file Reads file list from the specified file(/ stands for console). /C:string Uses specified string as a literal search string. /G:file Gets search strings from the specified file(/ stands for console). /D:dir Search a semicolon delimited list of directories strings Text to be searched for. [drive:][path]filename Specifies a file or files to search. Use spaces to separate multiple search strings unless the argument is prefixed with /C. For example, 'FINDSTR "hello there" x.y' searches for "hello" or "there" in file x.y. 'FINDSTR /C:"hello there" x.y' searches for "hello there" in file x.y. Regular expression quick reference: . Wildcard: any character * Repeat: zero or more occurances of previous character or class ^ Line position: beginning of line $ Line position: end of line [class] Character class: any one character in set [^class] Inverse class: any one character not in set [x-y] Range: any characters within the specified range \x Escape: literal use of metacharacter x \<xyz Word position: beginning of word xyz\> Word position: end of word For full information on FINDSTR regular expressions refer to the online Command Reference.

    Read the article

  • Issues Converting Plain Text Into Microsoft Word Bulleted Lists

    - by user787832
    I'm a programmer. I hate status reports. I found a way to live with it. While I am working in my IDE ( Visual Slickedit ) I keep a plain text file open in one of the file/buffer tabs. As I finish things I just jot down a quick note into that file. At the end of the week that becomes my weekly status report. Example entries: The Datatables.net plugin runs very slowly in IE 8 with more than 2,000 records. I changed the way I did the server side code to process the data to make less work for the plugin to get decent performance for the IE 8 users. I made a class to wrap data from the new data collection objects into the legacy data holder objects. This will let the new database code be backward compatible with the legacy code until we can replace it. I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site At the end of the month I go back to each weekly *.txt file and paste all of the entries into a MS Word file for a monthly report. I give the monthly report to a liason to the contracting company who has to compile everyone's monthly reports into a single MS Word 2007 document. His problem, soon to be my problem, comes when he highlights my paragraphs like the ones above to put bullets in front of my paragraphs. When he highlights my notes to put bullets in front of them with MS Word 2007, Word rearranges the text a bit and the new line chars/carriage returns stagger the text so the text is no longer in neat chunks. This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site Becomes This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site I tried turning word wrap on in my IDE for the text files I put my status notes in. It just puts some kind of newline character in anyway. Searching/Replacing those chars in the text files has the result of destroying the paragraphs. Once my notes are pasted into MS Word, Word automatically translates them into paragraph breaks. Searching/Replacing them there has similar results. Blank lines separating the notes disappears. One big mess. What I would like is to be able to keep adding my status notes to a text file as I am now, but do something different when I paste the notes into MS Word such that my liason can select the text, hit the bulleting command and NOT have the staggered text as shown above. Any ideas? Thanks much in advance Steve

    Read the article

  • Cannot open simplest mac application

    - by streetpc
    I created a very simple app, which is only a wrapper of a shell script (so that I can select this script in application selectors, like startup apps). I try to launch it and yesterday it worked, but today I changed the executable script's content and name (with something that perfeclty works in a shell script launched in the Terminal) and it will only display a Finder-iconed dialog saying Cannot open the application because it is not supported on this kind of Mac. I restored the previous script (content/name) but I still get the error! Same when re-bundling the app from scratch, or completely changing the bundle identifier… If I try to open it in the Terminal using open My.app, I get The application cannot be opened because it has an incorrect executable format. But when I executes directly the Contents/MacOS/Script, it allways works (iwth both contents). Also, it is displayed with correct icon and meta-information in the Finder (so I guess the Info.plist is understood). The app's file tree is: Contents/ Info.plist MacOS/ Script (executable bit set, works when launched directly) PkgInfo Resources/ AppIcon.icns Here is the Info.plist content: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>CFBundleExecutable</key> <string>Script</string> <key>CFBundleIconFile</key> <string>AppIcon</string> <key>CFBundleIdentifier</key> <string>asdf.ScriptApp</string> <key>CFBundleInfoDictionaryVersion</key> <string>6.0</string> <key>CFBundleName</key> <string>My script</string> <key>CFBundlePackageType</key> <string>APPL</string> <key>CFBundleShortVersionString</key> <string>1.0</string> <key>CFBundleSignature</key> <string>????</string> <key>CFBundleVersion</key> <string>1</string> <key>LSMinimumSystemVersion</key> <string>10.4</string> </dict> </plist> And the PkgInfo file only contains APPL????. I tested the Script with a simple echo "ok" and echo "ok" >/tmp/test (plus #!/bin/sh header). So my questions are: * Is there some kind of validity caching for applications ? based on what ? how do I flush it ? * Where does this message come from ? I tried to google it but all I get is a page talking about 32/64 bits Java…

    Read the article

  • Can spliting an access database cause printer and reporting issues?

    - by leeand00
    We have a setup in which our users log into an access database using MS Access 2003 over an RDP connection. The user's login to their own machines first using a roaming profile. They then click an rdp connection file on the desktop and login to the remote server, via RDP, where they use MS Access as the shell; they don't have any access to any of explorer.exe features such as the start menu. The database they are logging into is more of an application, and provides functionality for entering data, querying data, and running reports via form based menus. It all worked pretty well until we split the database as it was nearing 2GBs in size. We moved out the payroll data into a separate partition, a database with the same name in a different folder, both of them on the server. Only two tables were moved into this new database partition, and they were re-linked as external tables in the new partition. Now while everything appears to be working fine data-wise after the split, there's a new issue when our users login via RDP and attempt to run reports: often the report will not display and instead the user sees an error about the click event of the form. At first I didn't even know it was printer-related, as we didn't really change anything related to the printers as far as I knew. Confused about the error, I talked to the guy who previously worked here and who was in charge of splitting the database, and he told me to tell the users to set their default printers (on their local machines, not on the server) to the "printer" Microsoft XPS Document Writer which isn't a physical printer at all. This allowed the user's to display their reports, but if they want to print out reports, they are required to go to the File menu and select Print, clicking the print icon on the toolbar takes them to a Save As... dialog as would be expected when using the Microsoft XPS Document Writer as your default printer. It's easy to tell if the user is having a problem because a quick mouseover of the printer icon will yield a tooltip of (none) when they cannot access their reports, and a tooltip of Microsoft XPS Document Writer when they can view the reports. If the user's printer is set to anything other than Microsoft XPS Document Writer as the default on their local machine, then (none) is always displayed when they rdp to the database. The RDP settings are setup to transfer the local printer to the server. Telling the users to do this to print has been more of a band-aid on the whole situation until we find a better solution and an explanation as to why splitting a database would prevent users from printing or even viewing access database reports. Which is why I'm here asking this question. Also of note all the printers on the network now show up on the server so that when the users do click File->Print to print their reports on a physical printer, they have to look through a huge list of printers to find theirs in the dropdown. So the little band-aid fix we have is not ideal. Previously, only the printers on the user's local machine displayed here, and not all the printers on the network. My co-worker seems to think this has something to do with permissions, I personally think it has to do with roaming profiles, and Group Policies which is what I've been reading up on. I really don't know how to fix this or how it is related to splitting the database.

    Read the article

  • VPS 512 MB RAM with WordPressMU comes to consumes lots of memory

    - by CAPitalZ
    I have googled for days and gathered all optimization suggestions and tried. My sites are not getting any high hits. May be like 100 hits per day [all my sites combined]. Here are my specs I have 512 MB RAM VPS with burstable 1024 MB. Centos 5 32-bit & cPanel/WHM Apache 2.2 MySQL 5.0 PHP 5.3.2 Here is my Configs I have 2 WordPressMU production sites, and 1 test site my.cnf # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/lib/mysql/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/lib/mysql/mysql.sock skip-locking skip-bdb skip-innodb key_buffer = 16M max_allowed_packet = 1M table_cache = 64 sort_buffer_size = 512K net_buffer_length = 8K read_buffer_size = 256K read_rnd_buffer_size = 512K myisam_sort_buffer_size = 8M #CAPitalZ thread_cache_size=8 thread_concurrency=4 #query_cache_type=1 #query_cache_limit=1M query_cache_size=16M concurrent_insert=2 low_priority_updates=1 max_connections=50 tmp_table_size=16M max_heap_table_size=16M join_buffer_size=1M interactive_timeout=25 wait_timeout=1000 #connect_timout=10 not able to restart mysql max_connect_errors=10 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # skip-networking # Disable Federated by default skip-federated # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 [mysqld_safe] open_files_limit=8192 [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [myisamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [mysqlhotcopy] interactive-timeout httpd.conf I have unselected many modules and recompiled using EasyApache in WHM. Only have the following modules built Deflate Expires Fileprotect Imagemap MPM Prefork Version [default] EAccelerator for PHP Bcmath Calendar CurlSSL [I'm using Curl. But I don't have any https sites] Expat GD [for image cropping] Gettext Imap Mbregex [default] Mbstring [need both Mbregex and Mbstring for utf-8] Mysql of the system MySQL "Improved" extension. Sockets TTF (FreeType) [I'm using custom font] Zlib Under Global Configuration I only have FollowSymLinks enabled I Have TraceEnable, ServerSignature, FileETag OFF ServerTokens ProductOnly DirectoryIndex Priority has index.php as the first one I have removed Clamd [Clam Anti-virus] SpamAssasin is Off Under Tweak Settings Default catch-all/default address behavior for new accounts. This is set to "fail" All stats programs turned off I have eAccelerator installed and checked in phpinfo and its working [Pre VirtualHost Include under WHM] Timeout 20 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 3 MinSpareServers 1 MaxSpareServers 3 StartServers 1 ServerLimit 50 MaxClients 50 MaxRequestsPerChild 4000 ExtendedStatus Off #ServerType standalone this throws error HostnameLookups Off <Directory "/"> AllowOverride None </Directory> My sites will take ages to load and WHM/CPanel will not even load. adadaa.com/ http://adadaa.net/ kadais.ca/ My average memory consumption is like 1000 MB! [yes always bursting] The process that consumes most CPU and also most memory is mysql But I also get like 15 httpd processes [when its bursting] I already got warning from cpuwatchcheck saying "While processing, the cpu has been maxed out for more than a 6 hour period. The current load/uptime line on the server at the time of this email is 07:00:37 up 11:30, 0 users, load average: 14.64, 16.79, 20.07" I don't know, I have tried switching these config values many different times, but nothing seems to work. Please show some light... Thanks

    Read the article

  • Cannot open simplest script mac application

    - by streetpc
    I created a very simple app, which is only a wrapper of a shell script (so that I can select this script in application selectors, like startup apps). I try to launch it and yesterday it worked, but today I changed the executable script's content and name (with something that perfeclty works in a shell script launched in the Terminal) and it will only display a Finder-iconed dialog saying Cannot open the application because it is not supported on this kind of Mac. I restored the previous script (content/name) but I still get the error! Same when re-bundling the app from scratch, or completely changing the bundle identifier… If I try to open it in the Terminal using open My.app, I get The application cannot be opened because it has an incorrect executable format. But when I executes directly the Contents/MacOS/Script, it allways works (iwth both contents). Also, it is displayed with correct icon and meta-information in the Finder (so I guess the Info.plist is understood). The app's file tree is: Contents/ Info.plist MacOS/ Script (executable bit set, works when launched directly) PkgInfo Resources/ AppIcon.icns Here is the Info.plist content: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>CFBundleExecutable</key> <string>Script</string> <key>CFBundleIconFile</key> <string>AppIcon</string> <key>CFBundleIdentifier</key> <string>asdf.ScriptApp</string> <key>CFBundleInfoDictionaryVersion</key> <string>6.0</string> <key>CFBundleName</key> <string>My script</string> <key>CFBundlePackageType</key> <string>APPL</string> <key>CFBundleShortVersionString</key> <string>1.0</string> <key>CFBundleSignature</key> <string>????</string> <key>CFBundleVersion</key> <string>1</string> <key>LSMinimumSystemVersion</key> <string>10.4</string> </dict> </plist> And the PkgInfo file only contains APPL????. I tested the Script with a simple echo "ok" and echo "ok" >/tmp/test (plus #!/bin/sh header). So my questions are: Is there some kind of validity caching for applications ? based on what ? how do I flush it ? Where does this message come from ? I tried to google it but all I get is a page talking about 32/64 bits Java…

    Read the article

  • Windows 8.1 Update 1 Disk Usage 100%

    - by Gookjin Jeong
    Background Information / Computer Specs I have a 14-inch Samsung Series 5 Ultra. Core i5 CPU, 750GB HDD, 8GB RAM, Intel HD Graphics 4000. I've had the computer for about 1.5 years with no major problems. Problem The issue appeared at the beginning of April this year, when I updated the OS to Windows 8.1 Update 1 (not from 8 to 8.1). After being on continually (except for at night, when I put it on sleep mode) for about 48 hours, the disk usage as seen by Task Manager hits 100%. When this happens, everything from opening/closing applications to typing and even bringing up the start screen by pressing the Windows key becomes extremely slow. The only way to make the disk usage decrease is to restart the computer. Then the problem repeats. I've used my current laptop (as well as my previous laptops) this way -- putting it on sleep mode at night and restarting it only when Windows needs to install updates -- for a long time. So I know the 100% disk usage is not due to the way I use the computer. The thing that causes the spike varies. Sometimes it's System, sometimes it's one of the various applications I installed (e.g. Chrome, Evernote, Spotify, Wunderlist, iTunes, etc.), and sometimes it's Antimalware Service Executable, etc. Tried Solutions I think I tried almost every solution out there for this problem: Running the check disk command (chkdsk /b /f /v /scan c:) from Admin Command Prompt Running Windows Memory Diagnostic Disabling Superfetch and Windows Search from services.msc Running "Fix problems with Windows Update" from Control Panel -- Troubleshooting Updating and rolling back the graphics driver (Intel HD 4000) Disabling "Use hardware acceleration when available" from Chrome settings Disabling Intel Rapid Storage Technology Running the SFC /SCANNOW command as recommended here Running a quick scan & a full scan from Windows Defender (no threats found) Taking the hard drive out and putting it back Refreshing the computer, from the Update and recovery -- Recovery option in Windows settings NONE of the above worked for me. I was about to give up but then noticed that one of the main culprits of the disk usage spike, as shown in the "Disk Activity" section of the Resource Monitor, was C:\System (pagefile.sys). I googled around and found that one of the recommended solutions was to disable pagefile. I then went to **Control Panel -- System and Security -- System -- Advanced system settings -- Advanced tab -- Performance settings -- Advanced tab -- "Change" under Virtual memory and discovered that the number for "Currently allocated" at the bottom was 1280MB, although the number for "Recommended" was 4533MB. I immediately changed it to 4533MB and checked my family members' computers to see what the numbers were like. All of theirs had a currently allocated space that was only slightly smaller than the recommended space. See screenshot below: This might fix the problem. I'll have to wait a couple more days.But if it doesn't, what in the world should I do next? I'm guessing the hard drive isn't failing because This computer is less than 2 years old; and Speccy says that the status of the HDD is good. Update 5/27/2014 The "4533MB" solution did not work. I had to reboot the computer about 30 minutes ago because the disk usage again hit 100%. When I opened Resource Monitor the C:\System (pagefile.sys) again was shown to be the culprit. I have now disabled pagefile entirely via the same window shown above in the screenshot. The number for "currently allocated" is now 0MB. Will update again in a couple days, or if the problem occurs again, whichever comes sooner.

    Read the article

  • mySQL Optimization Suggestions

    - by Brian Schroeter
    I'm trying to optimize our mySQL configuration for our large Magento website. The reason I believe that mySQL needs to be configured further is because New Relic has shown that our SELECT queries are taking a long time (20,000+ ms) in some categories. I ran MySQLTuner 1.3.0 and got the following results... (Disclaimer: I restarted mySQL earlier after tweaking some settings, and so the results here may not be 100% accurate): >> MySQLTuner 1.3.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering [OK] Currently running supported MySQL version 5.5.37-35.0 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +ARCHIVE +BLACKHOLE +CSV -FEDERATED +InnoDB +MRG_MYISAM [--] Data in MyISAM tables: 7G (Tables: 332) [--] Data in InnoDB tables: 213G (Tables: 8714) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [--] Data in MEMORY tables: 0B (Tables: 353) [!!] Total fragmented tables: 5492 -------- Security Recommendations ------------------------------------------- [!!] User '@host5.server1.autopartsnetwork.com' has no password set. [!!] User '@localhost' has no password set. [!!] User 'root@%' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 5h 3m 4s (5M q [317.443 qps], 42K conn, TX: 18B, RX: 2B) [--] Reads / Writes: 95% / 5% [--] Total buffers: 35.5G global + 184.5M per thread (1024 max threads) [!!] Maximum possible memory usage: 220.0G (174% of installed RAM) [OK] Slow queries: 0% (6K/5M) [OK] Highest usage of available connections: 5% (61/1024) [OK] Key buffer size / total MyISAM indexes: 512.0M/3.1G [OK] Key buffer hit rate: 100.0% (102M cached / 45K reads) [OK] Query cache efficiency: 66.9% (3M cached / 5M selects) [!!] Query cache prunes per day: 3486361 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 812K sorts) [!!] Joins performed without indexes: 1328 [OK] Temporary tables created on disk: 11% (126K on disk / 1M total) [OK] Thread cache hit rate: 99% (61 created / 42K connections) [!!] Table cache hit rate: 19% (9K open / 49K opened) [OK] Open file limit used: 2% (712/25K) [OK] Table locks acquired immediately: 100% (5M immediate / 5M locks) [!!] InnoDB buffer pool / data size: 32.0G/213.4G [OK] InnoDB log waits: 0 -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Enable the slow query log to troubleshoot bad queries Increasing the query_cache size over 128M may reduce performance Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Read this before increasing table_cache over 64: http://bit.ly/1mi7c4C Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 512M) [see warning above] join_buffer_size (> 128.0M, or always use indexes with joins) table_cache (> 12288) innodb_buffer_pool_size (>= 213G) My my.cnf configuration is as follows... [client] port = 3306 [mysqld_safe] nice = 0 [mysqld] tmpdir = /var/lib/mysql/tmp user = mysql port = 3306 skip-external-locking character-set-server = utf8 collation-server = utf8_general_ci event_scheduler = 0 key_buffer = 512M max_allowed_packet = 64M thread_stack = 512K thread_cache_size = 512 sort_buffer_size = 24M read_buffer_size = 8M read_rnd_buffer_size = 24M join_buffer_size = 128M # for some nightly processes client sessions set the join buffer to 8 GB auto-increment-increment = 1 auto-increment-offset = 1 myisam-recover = BACKUP max_connections = 1024 # max connect errors artificially high to support behaviors of NetScaler monitors max_connect_errors = 999999 concurrent_insert = 2 connect_timeout = 5 wait_timeout = 180 net_read_timeout = 120 net_write_timeout = 120 back_log = 128 # this table_open_cache might be too low because of MySQL bugs #16244691 and #65384) table_open_cache = 12288 tmp_table_size = 512M max_heap_table_size = 512M bulk_insert_buffer_size = 512M open-files-limit = 8192 open-files = 1024 query_cache_type = 1 # large query limit supports SOAP and REST API integrations query_cache_limit = 4M # larger than 512 MB query cache size is problematic; this is typically ~60% full query_cache_size = 512M # set to true on read slaves read_only = false slow_query_log_file = /var/log/mysql/slow.log slow_query_log = 0 long_query_time = 0.2 expire_logs_days = 10 max_binlog_size = 1024M binlog_cache_size = 32K sync_binlog = 0 # SSD RAID10 technically has a write capacity of 10000 IOPS innodb_io_capacity = 400 innodb_file_per_table innodb_table_locks = true innodb_lock_wait_timeout = 30 # These servers have 80 CPU threads; match 1:1 innodb_thread_concurrency = 48 innodb_commit_concurrency = 2 innodb_support_xa = true innodb_buffer_pool_size = 32G innodb_file_per_table innodb_flush_log_at_trx_commit = 1 innodb_log_buffer_size = 2G skip-federated [mysqldump] quick quote-names single-transaction max_allowed_packet = 64M I have a monster of a server here to power our site because our catalog is very large (300,000 simple SKUs), and I'm just wondering if I'm missing anything that I can configure further. :-) Thanks!

    Read the article

  • Spring 3.0: Unable to locate Spring NamespaceHandler for XML schema namespace

    - by Nick Hristov
    My setup is fairly simple: I have a web front-end, back-end is spring-wired. I am using AOP to add a layer of security on my rpc services. It's all good, except for the fact that the web app aborts on launch: [java] SEVERE: Context initialization failed [java] org.springframework.beans.factory.parsing.BeanDefinitionParsingException: Configuration problem: Unable to locate Spring NamespaceHandler for XML schema namespace [http://www.springframework.org/schema/aop] [java] Offending resource: ServletContext resource [/WEB-INF/gwthandler-servlet.xml] Here is the snippet from my xml config file: <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:aop="http://www.springframework.org/schema/aop" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans.xsd http://www.springframework.org/schema/aop http://www.springframework.org/schema/aop/spring-aop.xsd"> <aop:config> <aop:aspect id="security" ref="securityAspect" > <aop:pointcut id="securedServices" expression="@annotation(com.fb.boog.common.aspects.Secured)"/> <aop:before method="checkSecurity" pointcut-ref="securedServices"/> </aop:aspect> </aop:config> I read over the internets that it may be my classloading the core of the problem. Doubtful, since here is my WEB-INF/lib directory: ./WEB-INF/lib ./WEB-INF/lib/aopalliance-alpha1.jar ./WEB-INF/lib/aspectj-1.6.6.jar ./WEB-INF/lib/commons-collections.jar ./WEB-INF/lib/commons-logging.jar ./WEB-INF/lib/ehcache-core-1.7.0.jar ./WEB-INF/lib/ejb3-persistence.jar ./WEB-INF/lib/hibernate ./WEB-INF/lib/hibernate/antlr.jar ./WEB-INF/lib/hibernate/asm.jar ./WEB-INF/lib/hibernate/bsh-2.0b1.jar ./WEB-INF/lib/hibernate/cglib.jar ./WEB-INF/lib/hibernate/dom4j.jar ./WEB-INF/lib/hibernate/freemarker.jar ./WEB-INF/lib/hibernate/hibernate-annotations.jar ./WEB-INF/lib/hibernate/hibernate-shards.jar ./WEB-INF/lib/hibernate/hibernate-tools.jar ./WEB-INF/lib/hibernate/hibernate.jar ./WEB-INF/lib/hibernate/jtidy-r8-20060801.jar ./WEB-INF/lib/jabsorb ./WEB-INF/lib/jabsorb/jabsorb-1.3.1.jar ./WEB-INF/lib/jta.jar ./WEB-INF/lib/jyaml-1.3.jar ./WEB-INF/lib/postgresql-8.4-701.jdbc4.jar ./WEB-INF/lib/sjsxp.jar ./WEB-INF/lib/spring ./WEB-INF/lib/spring/org.springframework.aop-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.asm-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.aspects-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.beans-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.context-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.context.support-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.core-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.expression-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.instrument-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.instrument.tomcat-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.jdbc-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.jms-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.orm-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.oxm-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.test-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.transaction-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.web-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.web.portlet-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.web.servlet-3.0.0.RELEASE.jar ./WEB-INF/lib/spring/org.springframework.web.struts-3.0.0.RELEASE.jar ./WEB-INF/lib/testng-5.11-jdk15.jar ./WEB-INF/web.xml

    Read the article

  • Visual Studio build fails: unable to copy exe-file from obj\debug to bin\debug

    - by Nailuj
    This is a question asked before, both here on Stack Overflow and other places, but none of the suggestions I've found this far has helped me, so I just have to try asking a new question. Scenario: I have a simple Windows Forms application (C#, .NET 4.0, Visual Studio 2010). It has a couple of base forms that most other forms inherit from, it uses Entity Framework (and POCO classes) for database access. Nothing fancy, no multi-threading or anything. Problem: All was fine for a while. Then, all out of the blue, Visual Studio failed to build when I was about to launch the application. I got the warning "Unable to delete file '...bin\Debug\[ProjectName].exe'. Access to the path '...bin\Debug\[ProjectName].exe' is denied." and the error "Unable to copy file 'obj\x86\Debug\[ProjectName].exe' to 'bin\Debug\[ProjectName].exe'. The process cannot access the file 'bin\Debug\[ProjectName].exe' because it is being used by another process." (I get both the warning and the error when running Rebuild, but only the error when running Build - don't think that is relevant?) I understand perfectly fine what the warning and error message says: Visual Studio is obviously trying to overwrite the exe-file while it the same time has a lock on it for some reason. However, this doesn't help me find a solution to the problem... The only thing I've found working is to shut down Visual Studio and start it again. Building and launching then works, untill I make a change in some of the forms, then I have the same problem again and have to restart... Quite frustrating! As I mentioned above, this seems to be a known problem, so there are lots of suggested solutions. I'll just list what I've already tried here, so people know what to skip: Creating a new clean solution and just copy the files from the old solution. Adding the following to the following to the project's pre-build event: if exist "$(TargetPath).locked" del "$(TargetPath).locked"   if not exist "$(TargetPath).locked" if exist "$(TargetPath)" move "$(TargetPath)" "$(TargetPath).locked" Adding the following to the project properties (.csproj file): <GenerateResourceNeverLockTypeAssembliestrue</GenerateResourceNeverLockTypeAssemblies However, none of them worked for me, so you can probably see why I'm starting to get a bit frustrated. I don't know where else to look, so I hope somebody has something to give me! Is this a bug in VS, and if so is there a patch? Or has I done something wrong, do I have a circular reference or similar, and if so how could I find out? Any suggestions are highly appreciated :)

    Read the article

  • Android : launching diff activities under TabWidget

    - by rahul
    hiii I am trying to launch activities under each tab. I hav tried with following code public class Tab_Proj1 extends TabActivity { TabHost mTabHost ; public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); final Context context = getApplicationContext(); //mTabHost = (TabHost) this.findViewById(R.id.); mTabHost = getTabHost(); mTabHost.setup(); mTabHost.addTab(mTabHost.newTabSpec("tab_test4") .setIndicator("Contacts") .setContent(new Intent().setClass(context, Tab1Activity.class))); Tab1Activity is extending ListActivity. I m getting exception as:::::: 01-25 11:57:07.352: ERROR/AndroidRuntime(952): Uncaught handler: thread main exiting due to uncaught exception 01-25 11:57:07.382: ERROR/AndroidRuntime(952): java.lang.RuntimeException: Unable to start activity ComponentInfo{com.android.app.Tab_Proj1/com.android.app.Tab_Proj1.Tab_Proj1}: java.lang.RuntimeException: Could not create tab content because could not find view with id 2131034148 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.app.ActivityThread.performLaunchActivity(ActivityThread.java:2268) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.app.ActivityThread.handleLaunchActivity(ActivityThread.java:2284) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.app.ActivityThread.access$1800(ActivityThread.java:112) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.app.ActivityThread$H.handleMessage(ActivityThread.java:1692) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.os.Handler.dispatchMessage(Handler.java:99) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.os.Looper.loop(Looper.java:123) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.app.ActivityThread.main(ActivityThread.java:3948) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at java.lang.reflect.Method.invokeNative(Native Method) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at java.lang.reflect.Method.invoke(Method.java:521) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:782) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:540) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at dalvik.system.NativeStart.main(Native Method) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): Caused by: java.lang.RuntimeException: Could not create tab content because could not find view with id 2131034148 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.widget.TabHost$ViewIdContentStrategy.(TabHost.java:539) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.widget.TabHost$ViewIdContentStrategy.(TabHost.java:530) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.widget.TabHost$TabSpec.setContent(TabHost.java:417) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at com.android.app.Tab_Proj1.Tab_Proj1.onCreate(Tab_Proj1.java:52) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.app.Instrumentation.callActivityOnCreate(Instrumentation.java:1123) 01-25 11:57:07.382: ERROR/AndroidRuntime(952): at android.app.ActivityThread.performLaunchActivity(ActivityThread.java:2231) ====================================================================== Am I going in correct way? If not please help me with some ideas..... thanks

    Read the article

  • Silverlight animation not smooth

    - by Andrej
    Hi, When trying to animate objects time/frame based in Silverlight (in contrast to using something like DoubleAnimation or Storyboard, which is not suitable e.g. for fast paced games), for example moving a spaceship in a particular direction every frame, the movement is jumpy and not really smooth. The screen even seems to tear. There seems to be no difference between CompositionTarget and DistpatcherTimer. I use the following approach (in pseudocode): Register Handler to Tick-Event of a DispatcherTimer In each Tick: Compute the elapsed time from the last frame in milliseconds Object.X += movementSpeed * ellapsedMilliseconds This should result in a smooth movement, right? But it doesn't. Here is an example (Controls: WASD and Mouse): Silverlight Game. Although the effect I described is not too prevalent in this sample, I can assure you that even moving a single rectangle over a canvas produces a jumpy animation. Does someone have an idea how to minimize this. Are there other approaches to to frame based animation exept using Storyboards/DoubleAnimations which could solve this? Edit: Here a quick and dirty approach, animating a rectangle with minimum code (Controls: A and D) Animation Sample Xaml: <Grid x:Name="LayoutRoot" Background="Black"> <Canvas Width="1000" Height="400" Background="Blue"> <Rectangle x:Name="rect" Width="48" Height="48" Fill="White" Canvas.Top="200" Canvas.Left="0"/> </Canvas> </Grid> C#: private bool isLeft = false; private bool isRight = false; private DispatcherTimer timer = new DispatcherTimer(); private double lastUpdate; public Page() { InitializeComponent(); timer.Interval = TimeSpan.FromMilliseconds(1); timer.Tick += OnTick; lastUpdate = Environment.TickCount; timer.Start(); } private void OnTick(object sender, EventArgs e) { double diff = Environment.TickCount - lastUpdate; double x = Canvas.GetLeft(rect); if (isRight) x += 1 * diff; else if (isLeft) x -= 1 * diff; Canvas.SetLeft(rect, x); lastUpdate = Environment.TickCount; } private void UserControl_KeyDown(object sender, KeyEventArgs e) { if (e.Key == Key.D) isRight = true; if (e.Key == Key.A) isLeft = true; } private void UserControl_KeyUp(object sender, KeyEventArgs e) { if (e.Key == Key.D) isRight = false; if (e.Key == Key.A) isLeft = false; } Thanks! Andrej

    Read the article

  • Nhibernate 2.1 and mysql 5 - InvalidCastException on Setup

    - by Nash
    Hello there, I am trying to use NHibernate with Spring.Net und mySQL 5. However, when setting up the connection and creating the SessionFactoryObject, I get this InvalidCastException: NHibernate seems to cast MySql.Data.MySqlClient.MySqlConnection to System.Data.Common.DbConnection which causes the exception. System.InvalidCastException wurde nicht behandelt. Message="Das Objekt des Typs \"MySql.Data.MySqlClient.MySqlConnection\" kann nicht in Typ \"System.Data.Common.DbConnection\" umgewandelt werden." Source="NHibernate" StackTrace: bei NHibernate.Tool.hbm2ddl.SuppliedConnectionProviderConnectionHelper.Prepare() in c:\CSharp\NH\nhibernate\src\NHibernate\Tool\hbm2ddl\SuppliedConnectionProviderConnectionHelper.cs:Zeile 25. bei NHibernate.Tool.hbm2ddl.SchemaMetadataUpdater.GetReservedWords(Dialect dialect, IConnectionHelper connectionHelper) in c:\CSharp\NH\nhibernate\src\NHibernate\Tool\hbm2ddl\SchemaMetadataUpdater.cs:Zeile 43. bei NHibernate.Tool.hbm2ddl.SchemaMetadataUpdater.Update(ISessionFactory sessionFactory) in c:\CSharp\NH\nhibernate\src\NHibernate\Tool\hbm2ddl\SchemaMetadataUpdater.cs:Zeile 17. bei NHibernate.Impl.SessionFactoryImpl..ctor(Configuration cfg, IMapping mapping, Settings settings, EventListeners listeners) in c:\CSharp\NH\nhibernate\src\NHibernate\Impl\SessionFactoryImpl.cs:Zeile 169. bei NHibernate.Cfg.Configuration.BuildSessionFactory() in c:\CSharp\NH\nhibernate\src\NHibernate\Cfg\Configuration.cs:Zeile 1090. bei OrmTest.Program.Main(String[] args) in C:\Users\Max\Documents\Visual Studio 2008\Projects\OrmTest\OrmTest\Program.cs:Zeile 24. bei System.AppDomain._nExecuteAssembly(Assembly assembly, String[] args) bei System.AppDomain.ExecuteAssembly(String assemblyFile, Evidence assemblySecurity, String[] args) bei Microsoft.VisualStudio.HostingProcess.HostProc.RunUsersAssembly() bei System.Threading.ThreadHelper.ThreadStart_Context(Object state) bei System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) bei System.Threading.ThreadHelper.ThreadStart() InnerException: I am using the programmatically setup approach in order to get a quick NHibernate Setup. Here is the setup Code: Configuration config = new Configuration(); Dictionary props = new Dictionary(); props.Add("dialect", "NHibernate.Dialect.MySQL5Dialect"); props.Add("connection.provider", "NHibernate.Connection.DriverConnectionProvider"); props.Add("connection.driver_class", "NHibernate.Driver.MySqlDataDriver"); props.Add("connection.connection_string", "Server=localhost;Database=orm_test;User ID=root;Password=password"); props.Add("proxyfactory.factory_class", "NHibernate.ByteCode.Spring.ProxyFactoryFactory, NHibernate.ByteCode.Spring"); config.AddProperties(props); config.AddFile("Person.hbm.xml"); ISessionFactory factory = config.BuildSessionFactory(); ISession session = factory.OpenSession(); Is something missing? I downloaded the current mysql Connector from the mysql Website.

    Read the article

  • Entity Framework SaveChanges error details

    - by Marek Karbarz
    When saving changes with SaveChanges on a data context is there a way to determine which Entity causes an error? For example, sometimes I'll forget to assign a date to a non-nullable date field and get "Invalid Date Range" error, but I get no information about which entity or which field it's caused by (I can usually track it down by painstakingly going through all my objects, but it's very time consuming). Stack trace is pretty useless as it only shows me an error at the SaveChanges call without any additional information as to where exactly it happened. Note that I'm not looking to solve any particular problem I have now, I would just like to know in general if there's a way to tell which entity/field is causing a problem. Quick sample of a stack trace as an example - in this case an error happened because CreatedOn date was not set on IAComment entity, however it's impossible to tell from this error/stack trace [SqlTypeException: SqlDateTime overflow. Must be between 1/1/1753 12:00:00 AM and 12/31/9999 11:59:59 PM.] System.Data.SqlTypes.SqlDateTime.FromTimeSpan(TimeSpan value) +2127345 System.Data.SqlTypes.SqlDateTime.FromDateTime(DateTime value) +232 System.Data.SqlClient.MetaType.FromDateTime(DateTime dateTime, Byte cb) +46 System.Data.SqlClient.TdsParser.WriteValue(Object value, MetaType type, Byte scale, Int32 actualLength, Int32 encodingByteSize, Int32 offset, TdsParserStateObject stateObj) +4997789 System.Data.SqlClient.TdsParser.TdsExecuteRPC(_SqlRPC[] rpcArray, Int32 timeout, Boolean inSchema, SqlNotificationRequest notificationRequest, TdsParserStateObject stateObj, Boolean isCommandProc) +6248 System.Data.SqlClient.SqlCommand.RunExecuteReaderTds(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, Boolean async) +987 System.Data.SqlClient.SqlCommand.RunExecuteReader(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, String method, DbAsyncResult result) +162 System.Data.SqlClient.SqlCommand.RunExecuteReader(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, String method) +32 System.Data.SqlClient.SqlCommand.ExecuteReader(CommandBehavior behavior, String method) +141 System.Data.SqlClient.SqlCommand.ExecuteDbDataReader(CommandBehavior behavior) +12 System.Data.Common.DbCommand.ExecuteReader(CommandBehavior behavior) +10 System.Data.Mapping.Update.Internal.DynamicUpdateCommand.Execute(UpdateTranslator translator, EntityConnection connection, Dictionary`2 identifierValues, List`1 generatedValues) +8084396 System.Data.Mapping.Update.Internal.UpdateTranslator.Update(IEntityStateManager stateManager, IEntityAdapter adapter) +267 [UpdateException: An error occurred while updating the entries. See the inner exception for details.] System.Data.Mapping.Update.Internal.UpdateTranslator.Update(IEntityStateManager stateManager, IEntityAdapter adapter) +389 System.Data.EntityClient.EntityAdapter.Update(IEntityStateManager entityCache) +163 System.Data.Objects.ObjectContext.SaveChanges(SaveOptions options) +609 IADAL.IAController.Save(IAHeader head) in C:\Projects\IA\IADAL\IAController.cs:61 IA.IAForm.saveForm(Boolean validate) in C:\Projects\IA\IA\IAForm.aspx.cs:198 IA.IAForm.advance_Click(Object sender, EventArgs e) in C:\Projects\IA\IA\IAForm.aspx.cs:287 System.Web.UI.WebControls.Button.OnClick(EventArgs e) +118 System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) +112 System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent(String eventArgument) +10 System.Web.UI.Page.RaisePostBackEvent(IPostBackEventHandler sourceControl, String eventArgument) +13 System.Web.UI.Page.RaisePostBackEvent(NameValueCollection postData) +36 System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +5019

    Read the article

< Previous Page | 322 323 324 325 326 327 328 329 330 331 332 333  | Next Page >