Search Results

Search found 9332 results on 374 pages for 'an original alias'.

Page 330/374 | < Previous Page | 326 327 328 329 330 331 332 333 334 335 336 337  | Next Page >

• Windows Server 2008 Software Raid 5 - Data integrity issues

  - by Fopedush

  I've got a server running Windows Server 2008 R2, with a (windows native) software raid-5 array. The array consists of 7x 1TB Western Digital RE3 and RE4 drives. I have offline backups of this array. The problem is this: I noticed a few days ago after copying a large file to the disk that there was an integrity issue with that file - it was a ~12GB file that I had downloaded via uTorrent. After moving it to the raid array, I used uTorrent to relocate the download location, and performed a re-check so I could seed it from that location. The recheck found that only 6308/6310 chunks of the copied file were intact. My next step was to write a quick powershell script that would copy files to the array, while performing a SHA1 hash of the original and resultant files and comparing them. Smaller files (100-1000MB) copied over just fine. When I started copying larger data (~15GB), I found that the hash check failed about 2/3rds of the time. The corrupt files had very, very small inconsistencies - less than .01%. I further eliminated the possibility of networking or client issues by placing this large file on the C:\ of the server, and copying it repeatedly from there to the array, seeing similar results. Copying the data via explorer, powershell, or the standard windows command prompt yield the same results. None of the copies fail or report any problems. The raid array itself is listed as healthy in disk management. After a few experiments, I shut down the server and ran memtest overnight. No errors were detected. A basic run of chkdsk found no problems, but I did not use the /R flag, as I was unsure how that might affect a software raid-5 volume. I next ran Crystal Disk Info to check the smart data on the drives - but found that CDI only detected 5 out of 7 of the disks in the array. I have no idea why. Nevertheless, CDI shows the following "caution" flags on a single one of the drives: 05 199 199 140 000000000001 Reallocated Sectors Count C5 200 200 __0 000000000001 Current Pending Sector Count Which is a little bit alarming, but I don't really know what to do with the information. I hardly feel like one reallocated sector could be causing this. At this point, I'm looking for some guidance on what to do next. I need to determine the cause of this issue, but I'm hesitant to run chkdsk /R or any bootable disk health checkers because I'm afraid they might break the array. I've considered triggering a re-sync of the array, but I'm not actually sure how to do that without doing something silly like manually dropping a disk and then restoring it. Any advice that could help me ferret out the precise cause of this issue would be greatly appreciated.

  Read the article

• MBPro, mid 2010 can't see Dlink DIR655 signal after sleep etc

  - by user88114

  This is my son's MBP 7,1 running Snow Leopard 10.6.7. Router signal is fine since iPad, Wintel on same table 20 feet from router are fine. the MBP however frequently wakes and fails to find the internet. iStumbler can see 1 neighbours hub and my garden hub are there but can't get to the normal DIR655 wifi... no ping no en0 or en1 device seems to exist. Airport off and on does not help. He just resets router and it all works but this does not please me! I must admit the winter sometimes seems to loose connect too, but less so. The DIR655 (hardware rev A3) is on the original EU firmware 1.10, I'm cautious about jumping to latest 1.31EU since no downgrade seems to be possible and that feels a bit risky as so much is set up and working fine. If I use the DIR655 admin web and release the lease the MBP has then wake it all worked OK. So I suspect lease timing/locking issue but unsure how to check up, plus why iStumbler seems to say the network is not visible at all when I sit on the iPad right next to it just fine.. I do not think there are any channel overlaps and we also have RFquiet DECT phones (Orchid) that are silent until lifted or called. Anyway signals all show low interference and high throughput except for this failure to connect. Just walked the MBP to the garden office and iStumbler now sees the more distant DIR655 signal although it will not connect to it (does not show under Sys Prefs NetNetwork names) even after airport off & on... It also refuses to connect to my garden network (an old Belkin acting as AP wired to DIR655), the signal it can see and even net name in Sys Prefs NetNetwork names (2 mins later):NOW both names ARE visible, but both fail to accept the correct WPA2 password and keep asking again after failing to connect. IT ALL MAKES NO SENSE TO ME. Just revoked the lease for the MBP on DIR655 and no changes although this seemed to help MBP wake into connection 1 hour ago. OK a bit of walking about to report. Carried MBP across garden towards DIR655, a few other wifis show up on iStumbler, low signals all channel 1. Right next to DIR655 but iStumbler not showing it, although most other wifi's have gone. I'd say iStubler is suffering timeouts&hangs but hard to be sure. Lots of attempts to Airport on/off, join other etc and suddenly I get to connect, get given new IP (I revoked), can browse. Walk away, connection drops quite soon at 30 feet then reconnected briefly then died again. MUST ATTEND ELSEWHERE FOR A BIT...

  Read the article

• PDF has garbled text when copy pasting

  - by ngm

  I'm trying to copy and paste text from a PDF file. However, whenever I paste the original text it is a huge mess of garbled characters. The text looks like the following (this is just one small extract): 4$/)5=$13! ,4&1*%-! )5'$! 1$2$)&,$40! 65))! .*5)1! -#$! )/'8*/8$03! (4/+$6&4;0!/'1!-&&)0!*0$1!.9!/,,)5%/-5&'!1$2$)&,$403!5'!+*%#!-#$! 0/+$!6/9! -#/-! &,$4/-5'8! 090-$+! 1$2$)&,$40! .*5)1!1$25%$! 1452$40! /'1! &-#$4! 090-$+! 0&(-6/4$! %&+,&'$'-0! *0$1! .9! /,,)5%/-5&'! 1$2$)&,$40!-&1/97!"#$!+5M!&(!,4&1*%-!)5'$!/'1!,4&1*%-!1$2$)&,$40! 65))! .$!+*%#!+&4$! $2$')9! ./)/'%$13! #&6$2$43! -#/'! -#$!+5M! &(! &,$4/-5'8!090-$+!/'1!/,,)5%/-5&'!1$2$)&,$40!-&1/97! )*+*+, C<88,?>8513AG<5A14, I've tried it in both Adobe and Foxit PDF readers. I did a 'Save as text' in Adobe Reader and the resultant text file is the same garbled text. Any ideas how I can get this text out non-garbled? (Other than manual typing... there's a lot of text to extract.)

  Read the article

• Exchange IMAP4 connector - Error Event ID 2006

  - by MikeB

  Hi, A couple of users in my organisation use IMAP4 to connect to Exchange 2007 (Update rollup 9 applied) because they prefer Thunderbird / Postbox clients. One of the users is generating errors in the Application Log as follows: An exception Microsoft.Exchange.Data.Storage.ConversionFailedException occurred while converting message Imap4Message 1523, user "*******", folder *********, subject: "******", date: "*******" into MIME format. Microsoft.Exchange.Data.Storage.ConversionFailedException: Message content has become corrupted. ---> System.ArgumentException: Value should be a valid content type in the form 'token/token' Parameter name: value at Microsoft.Exchange.Data.Mime.ContentTypeHeader.set_Value(String value) at Microsoft.Exchange.Data.Storage.MimeStreamWriter.WriteHeader(HeaderId type, String data) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeStreamAttachment(StreamAttachmentBase attachment, MimeFlags flags) --- End of inner exception stack trace --- at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeStreamAttachment(StreamAttachmentBase attachment, MimeFlags flags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeAttachment(MimePartInfo part, MimeFlags flags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimePart(MimePartInfo part, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeParts(List`1 parts, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimePart(MimePartInfo part, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ImapItemConverter.<>c__DisplayClass2.<WriteMimePart>b__0() at Microsoft.Exchange.Data.Storage.ConvertUtils.CallCts(Trace tracer, String methodName, String exceptionString, CtsCall ctsCall) at Microsoft.Exchange.Data.Storage.ImapItemConverter.WriteMimePart(ItemToMimeConverter converter, MimeStreamWriter writer, OutboundConversionOptions options, MimePartInfo partInfo, MimeFlags conversionFlags) at Microsoft.Exchange.Data.Storage.ImapItemConverter.GetBody(Stream outStream) at Microsoft.Exchange.Data.Storage.ImapItemConverter.GetBody(Stream outStream, UInt32[] indices) From my reading around it seems that the suggestion is to ask users to log in to Outlook / OWA and view the messages there. However, having logged in as the users myself, the messages cannot be found either through searching or by browsing the folder detailed in the log entry. The server returns the following error to the client: "The message could not be retrieved using the IMAP4 protocol. The message has not been deleted and may be accessible using either Microsoft Outlook or Microsoft Office Outlook Web Access. You can also try contacting the original sender of the message to find out about the contents of the message. Retrieval of this message will be retried when the server is updated with a fix that addresses the problem." Messages were transferred in to Exchange by copying them from the old Apple Xserve, accessed using IMAP. So my question, finally: 1. Is there any way to get the IMAP Exchange connector to rebuild its cache of messages since it doesn't seem to be pulling them directly from the MAPI store? 2. Alternatively, if there is no database, any ideas on why these messages don't appear in Outlook or OWA would be gratefully received. Many thanks, Mike

  Read the article

• DPM 2010 PowerShell Script to Easily Restore Multiple Files

  - by bmccleary

  I’ve got what I thought would be a simple task with Data Protection Manager 2010 that is turning out to be quite frustrating. I have a file server on one server and it is the only server in a protection group. This file server is the repository for a document management application which stores the files according to the data within a SQL database. Sometimes users inadvertently delete files from within our application and we need to restore them. We have all the information needed to restore the files to include the file name, the folder that the file was stored in and the exact date that the file was deleted. It is easy for me to restore the file from within the DPM console since we have a recovery point created every day, I simply go to the day before the delete, browse to the proper folder and restore the file. The problem is that using the DPM console, the cumbersome wizard requires about 20 mouse clicks to restore a single file and it takes 2-4 minutes to get through all the windows. This becomes very irritating when a client needs 100’s of files restored… it takes all day of redundant mouse clicks to restore the files. Therefore, I want to use a PowerShell script (and I’m a novice at PowerShell) to automate this process. I want to be able to create a script that I pass in a file name, a folder, a recovery point date (and a protection group/server name if needed) and simply have the file restored back to its original location with some sort of success/failure notification. I thought it was a simple basic task of a backup solution, but I am having a heck of a time finding the right code. I have seen the sample code at http://social.technet.microsoft.com/wiki/contents/articles/how-to-use-a-windows-powershell-script-to-recover-an-item-in-data-protection-manager.aspx that I have tried to follow, but it doesn’t accomplish what I really want to do (it’s too simplistic) and there are errors in the sample code. Therefore, I would like to get some help writing a script to restore these files. An example of the known values to restore the data are: DPM Server: BACKUP01 Protection Group: Document Repository Data Protected Server: FILER01 File Path: R:\DocumentRepository\ToBackup\ClientName\Repository\2010\07\24\filename.pdf Date Deleted: 8/2/2010 (last recovery point = 8/1/2010) Bonus Points: If you can help me not only create this script, but also show me how to automate by providing a text file with the above information that the PowerShell script loops through, or even better, is able to query our SQL server for the needed data, then I would be more than willing to pay for this development.

  Read the article

• Computer suddenly dies; screen displays weird flickering lines, then restarts

  - by Imray

  I've been having this terrible problem for a little while and just managed to get a picture of 'dead screen' for the first time and I am posting it to seek help. Randomly, at irregular intervals (typically once a week), while working on something (it's been different things every time) my computer will just suddenly go dead - the screen turns to exactly the picture below (the lines flicker a little bit), it hangs there for a few seconds and then restarts. Obviously this is extremely frustrating and I want to try to stop it. I've searched numerous postings with similar keywords but nothing exactly the same as mine. Does anyone have any idea what might be the cause of this? I would post all my system settings and installed programs but the list is long and I don't know how much relevance each item would be. If you'd like to know something specific, please comment and I'll let you know whatever you need. SPECS C:\Users\Imray>systeminfo Host Name: Imray OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Workstation OS Build Type: Multiprocessor Free Registered Owner: Imray - Owner Registered Organization: Product ID: 00371-152-9333854-85895 Original Install Date: 06/09/1999, 5:45:21 PM System Boot Time: 22/03/2013, 8:58:18 AM System Manufacturer: Gateway System Model: DX4840 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 37 Stepping 2 GenuineIntel ~3201 Mhz BIOS Version: American Megatrends Inc. P01-A3 , 17/05/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume2 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 6,135 MB Available Physical Memory: 3,632 MB Virtual Memory: Max Size: 12,268 MB Virtual Memory: Available: 8,114 MB Virtual Memory: In Use: 4,154 MB Page File Location(s): C:\pagefile.sys Domain: WORKGROUP Logon Server: \\Imray-OWNER Hotfix(s): 4 Hotfix(s) Installed. [01]: KB971033 [02]: KB958559 [03]: KB977206 [04]: KB981889 Network Card(s): 2 NIC(s) Installed. [01]: 802.11n Wireless PCI Express Card LAN Adapter Connection Name: Wireless Network Connection DHCP Enabled: Yes DHCP Server: 192.168.2.1 IP address(es) [01]: 192.168.2.13 [02]: fe80::1df1:5399:6890:91f6 [02]: Microsoft Virtual WiFi Miniport Adapter Connection Name: Wireless Network Connection 2 DHCP Enabled: Yes DHCP Server: N/A IP address(es) Graphics Card Specs Name ATI Radeon HD 5570 PNP Device ID PCI\VEN_1002&DEV_68D9&SUBSYS_E142174B&REV_00\4&18A4B35E&0&0008 Adapter Type ATI display adapter (0x68D9), ATI Technologies Inc. compatible Adapter Description ATI Radeon HD 5570 Adapter RAM 1.00 GB (1,073,741,824 bytes) Installed Drivers atiu9p64 aticfx64 aticfx64 atiu9pag aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64 Driver Version 8.700.0.0 INF File oem1.inf (ati2mtag_Evergreen section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1920 x 1080 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xDFFFFFFF Memory Address 0xFBDE0000-0xFBDFFFFF I/O Port 0x0000D000-0x0000DFFF IRQ Channel IRQ 4294967293 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\atikmpag.sys (8.14.1.6095, 181.00 KB (185,344 bytes), 06/09/1999 5:59 PM)

  Read the article

• Alternative Windows Offline Files + Windows Backup + Previous Version Setup

  - by Herson

  Currently our documents are all hosted in a Windows 7 box. Users can access the files using Windows share and the documents are available offline (windows 7 feature). The documents are being backed up daily by Windows 7 backup and restore utility. Users can access previous versions of the file (from the backups) using Windows Explorer "previous versions" feature. This setup is currently working well, except for the following: We would prefer to have access to hourly versions of the file, not daily. The previous version mechanism is tied up to the backup mechanism. Windows 7 performs a full backup every week and incremental backup everyday. The previous versions of a file is actually what are the available in the backups. If you 20GB documents and want to maintain at least three(3) year history, you will use at minimum 3 years * 52 weeks * 20GB or about 3TB even if there are few changes in the documents. Its pretty inefficient use of space. Looking up previous versions of a file is very slow (tens of minutes). This is probably related to the previous issue - Windows has to traverse its all of its backups. I am considering using SVN + autocommit/autoupdate tortoisesvn. It will have the following advantages: Backups are easy and will also backup the whole history of each documents. (Just backup the repository). Creating previous versions can be frequent. I think svn commit / update can be done every two minutes or so. Users can sync over the net. However, I can see the following issues: More conflicts than the original setup because both multiple users can now edit the same file even both are online, i.e. can connect to the SVN repo. The users can off course lock the file first before editing, but that would mean they have to adjust. Delay on propagation of file changes. On windows 7 file sharing, changes made by one online user will be instantaneously available to other online users. With the SVN setup, changes will only be propagated when the users execute the svn add/commit/update sequence. Delay will be probably a few minutes. This workflow will no longer work: "Hi, I just edited document X, can you have a quick look?" I would like to ask the opinion of the community for alternative setups, or improvements on the above setups to work out the kinks.

  Read the article

• Init script & the green [ OK ]

  - by Lord Loh.

  I am trying to install fast-cgi for nginx on an EC2 instance. I followed the steps explained here, but that is meant for Debian and does not work out of the box for a red-hat based system. I modified the script a bit to look like - #!/bin/bash ### BEGIN INIT INFO # Provides: php-fcgi # Required-Start: $nginx # Required-Stop: $nginx # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts php over fcgi # Description: starts php over fcgi ### END INIT INFO . /etc/rc.d/init.d/functions (( EUID )) && echo .You need to have root priviliges.. && exit 1 BIND=/tmp/php.socket USER=nginx PHP_FCGI_CHILDREN=15 PHP_FCGI_MAX_REQUESTS=1000 PHP_CGI=/usr/bin/php-cgi PHP_CGI_NAME=`basename $PHP_CGI` PHP_CGI_ARGS="- USER=$USER PATH=/usr/bin PHP_FCGI_CHILDREN=$PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=$PHP_FCGI_MAX_REQUESTS $PHP_CGI -b $BIND" RETVAL=0 start() { echo -n "Starting PHP FastCGI: " #ORIGINAL LINE #daemon $PHP_CGI --quiet --start --background --chuid "$USER" --exec /usr/bin/env -- $PHP_CGI_ARGS #MODIFIED LINE daemon --user=$USER $PHP_CGI -b $BIND& RETVAL=$? echo [ $RETVAL -eq 0 ] && touch /var/lock/subsys/php-fcgi #echo "$PHP_CGI_NAME." } stop() { echo -n "Stopping PHP FastCGI: " killall -q -w -u $USER $PHP_CGI RETVAL=$? echo "$PHP_CGI_NAME." rm /var/lock/subsys/php-fcgi } case "$1" in start) start ;; stop) stop ;; restart) stop start ;; *) echo "Usage: php-fastcgi {start|stop|restart}" exit 1 ;; esac exit $RETVAL The problem I have now is - service php-fcgi start keeps the shell blocked. If I run service php-fcgi start & and then ps aux, I see the php-cgi process running bound to the socket. I see the start command stop only when I execute service php-fcgi stop. How do I solve this blocking issue? I have tried adding an & at the end of the line spawning the daemon. But other scripts do not seem to be doing this. This is the most complicated script I am attempting to modify yet :-( How do I get the script to display the green [ OK ]? I checked scripts like httpd and saw that all they were doing was something as shown below. But I never see a green [ OK ] when I execute php-fcgi. I also discovered that putting echo_success with functions sourced displays the green [ OK ] but I do not see any other scripts in the /etc/rc.d/init.d/ executing echo_success or echo_failure. What have I got wrong? Also, How do i specify PHP_FCGI_CHILDREN with daemon? echo [ $RETVAL -eq 0 ] && touch /var/lock/subsys/

  Read the article

• Second HDD not seen by Windows 7 on Dell Xps l501x

  - by George

  I have a Dell XPS Laptop (l501x). I have replaced the original Seagate 500GB hard drive with an SSD Intel 320 120GB when I first purchased it a year ago. It's been working great. The laptop is booting in about 23 seconds, so the SSD is great. I have an Acronis image created that I came back to every three months just to keep everything clean. The SSD is partitioned with one logical drive for my data. So, recently I thought since I am not using my optical drive often enough to swap it out with a HDD caddy and add my seagate 500gb hard drive. I ordered the caddy placed the HDD in it and now load Windows. It just hangs on the screen that should show the Windows logo. I have tried everything that I know and searched it online. I have uninstalled the SATA controller AHCI and let Windows install it. Still will not boot into windows. I wanted to mention that the Seagate 500GB drive was the one that came with my laptop before I switched to the Intel SSD. As you know Intel has this application called Intel Rapid Technology which loads once in a while and shows the second hard drive, but then, when I restart it hangs again and Windows will not load. As soon as I remove the HDD Caddy and restart it loads Windows fine. I also formated the Seagate 500GB HDD in NTFS and still Windows will not load. When I go into the BIOS it shows the Fixed SSD and also "Sata ODD 500GB" instead of the optical drive but it will not boot into Windows when the HDD caddy is present. There is nothing wrong with the caddy. I have another laptop (Asus) and I installed the HDD caddy and Windows 7 loads without any glitch. I don't get it. I have also flashed the BIOS because Dell had a new version (A08). I also wanted to add that I refreshed Disk Management and the Device Manager and the second drive does not display. At this point I think it's a Windows issue so before I reinstall Windows 7 Home Premium from scratch I wanted to see if there was anything I was missing. Any advice would be greatly appreciated.

  Read the article

• SQL Clustering on Hyper V - is a cluster within a cluster a benefit.

  - by Chris W

  This is a re-hash of a question I asked a while back - after a consultant has come in firing ideas in to other teams in the department the whole issue has been raised again hence I'm looking for more detailed answers. We're intending to set-up a multi-instance SQL Cluster across a number of physical blades which will run a variety of different systems across each SQL instance. In general use there will be one virtual SQL instance running on each VM host. Again, in general operation each VM host will run on a dedicated underlying blade. The set-up should give us lots of flexibility for maintenance of any individual VM or underlying blade with all the SQL instances able to fail over as required. My original plan had been to do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Within the VMs - create a failover cluster and then install SQL Server clustering. The consultant has suggested that we instead do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Create a cluster on the HOST machines which will host all the VMs. Within the VMs - create a failover cluster and then install SQL Server clustering. The big difference is the addition of step 4 whereby we cluster all of the guest VMs as well. The argument is that it improves maintenance further since we have no ties at all between the SQL cluster and physical hardware. We can in theory live migrate the guest VMs around the hosts without affecting the SQL cluster at all so we for routine maintenance physical blades we move the SQL cluster around without interruption and without needing to failover. It sounds like a nice idea but I've not come across anything on the internet where people say they've done this and it works OK. Can I actually do the live migrations of the guests without the SQL Cluster hosted within them getting upset? Does anyone have any experience of this set up, good or bad? Are there some pros and cons that I've not considered? I appreciate that mirroring is also a valuable option to consider - in this case we're favouring clustering since it will do the whole of each instance and we have a good number of databases. Some DBs are for lumbering 3rd party systems that may not even work kindly with mirroring (and my understanding of clustering is that fail overs are completely transparent to the clients). Thanks.

  Read the article

• Confused with DKIM, SPF and Exim Configs

  - by 0pt1m1z3

  I've now spent 2 hours trying to figure out this issue and I am about to give up and go to bed. I've been having issues with Gmail rejecting emails from my VPS server because of false spam alerts (probably caused by lfd sending too many emails). So I changed my Exim config to send emails from a different IP (my VPS comes with 3) and that fixed the issue. I also enabled DKIM and SPF on my domains for added measure. But now, all my emails appear as ("From: Sender Name via server.domain1.com") where server.domain1.com is my VPS hostname. I previously had the same issue in Outlook and turning off "Set SMTP Sender: headers" solved that problem. But I believe adding the DKIM and SPF now makes Gmail add "via server.domain1.com" to my messages. How do I fix this? This is a typical header for a message (as it appears at gmail): Delivered-To: [email protected] Received: by 10.60.44.163 with SMTP id f3csp248622oem; Thu, 29 Mar 2012 21:23:18 -0700 (PDT) Received: by 10.50.106.200 with SMTP id gw8mr452788igb.10.1333081398523; Thu, 29 Mar 2012 21:23:18 -0700 (PDT) Return-Path: <[email protected]> Received: from domain2.com ([X.X.X.X]) by mx.google.com with ESMTPS id y1si810998igb.3.2012.03.29.21.23.18 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 29 Mar 2012 21:23:18 -0700 (PDT) Received-SPF: pass (google.com: domain of [email protected] designates X.X.X.X as permitted sender) client-ip=X.X.X.X; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates X.X.X.X as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=server.domain1.com; s=default; h=Date:Message-Id:From:Content-type:MIME-Version:Subject:To; bh=wF8bBRgh01EYg4t5DAeVPv1Ps906UVIeRnQCb/HvSYw=; b=k/Pg7lnrO+Ud/z1mOTv+O/3DiJzzQgyBhfIizIaFHM8tF/eNJt5P2k+9yQB224sxYstZIWwVRBJmiqvcM1QhARv1HWqWma0crppZ3JOn+LRHANan634OBi+58SIRA+gu; Received: (Exim 4.77) id 1SDTVE-0005HA-9Y for [email protected]; Fri, 30 Mar 2012 00:31:56 -0400 To: [email protected] Subject: Password Reset Request MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 From: Sender Name <[email protected]> Message-Id: <[email protected]> Date: Fri, 30 Mar 2012 00:31:56 -0400 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - server.domain1.com X-AntiAbuse: Original Domain - domain2.com X-AntiAbuse: Originator/Caller UID/GID - [507 504] / [47 12] X-AntiAbuse: Sender Address Domain - server.domain1.com

  Read the article

• Seriousness of a "Smart" disk error. How long will it last?

  - by Workshop Alex

  I have an 1 TB data disk and the bios and Windows are reporting a "Smart" error. At least, I get a Smart event but it doesn't indicate how serious the failure could be. My system is about 6 months old, including the disk so the warranty will cover the damage. Unfortunately, I lack a second disk of 1 TB in size which I can use to make a full backup. The most important data on this disk is safe, but there's a lot of work data which can be regenerated but this would cost a lot of time. So I ordered an USB disk of 1 TB which will arrive in three days. By then I can make a full backup of the data and afterwards, it can crash. But will the disk live that long? (Well, I won't use the PC as long as I can't make a backup.) How serious is such a Smart event? I know it's serious enough to have it replaced, but will it live for another week or could it die any moment?Update: I purchased an 1 TB external disk and spent most of the day making a backup of the 1 TB disk. It survived that. I then received a new disk, since it was still under warranty and replaced the hard disk. Then I had to spend most of a day again to put back the backup. I need to send back the faulty disk and now have an additional external disk, which could always be practical. :-) The Smart Error report did not cause any failures on the original disk. I won't advise to ignore these warnings, but the disk still has enough life in it to last a few more days. (Just make sure you have a good back-up.) And oh, the horror of having to make a complete backup such a huge disk. :-) If your data is important, make sure you have something that supports incremental backups and lots of space. (In my case, the data wasn't very important, just practical to have on-disk together.)

  Read the article

• Frequent and weird wifi disconnections

  - by Sidou

  How would you explain, troubleshoot (and solve) the following problem? Wifi ADSL modem router D-link 2640R installed in living room at about 1.8m height. Working fine, synchronising and getting/serving stable internet connection. First situation: -Laptop 01 in other end of the house, let's say in room01 southern to the living room, distant by about 15m. Getting stable signal of good to very good quality. No disconnection. -Laptop 02 in room02 opposite to room01 (5m West) which makes it almost at the same distance and direction from the router located 15m North. Getting stable signal of good to very good quality. No disconnection. Second situation: -Laptop 01 moved to room03 Northern to the living room (actually just 3m behind the wall where the router lies). Getting stable signal of excellent quality. No disconnection. -Laptop 02 still in room02 but now experiences frequent disconnections (actually almost impossible to get the Internet even though the signal level is still very good. Either no Internet with the wifi icon appearing connected to access point or no connection established at all which happens every 2 minutes and that means virtually no Internet at all as I can just get a timeframe of 1 minute or so to load any website or even get to the router's web based control panel. If Laptop 01 is completely shut down or its wifi adapters shut down or even still working but its wifi MAC address forbidden, then Laptop 02 has no problem at all. If Laptop 02 is moved to a nearer location to the router, in the living room for instance, then no connection problem occurs even if Laptop 01 is also connected. And also if we move back Laptop 01 to its original location (room 01), then no problem as well. I'm completely lost and don't know how to address this issue. I tried to change the Wifi channel and even tried the auto channel scan but that didn't solve it. I know that the problem is probably coming from Laptop 01 being in its new location or some sort of interference as the problem occurs only under the described condition but I have no idea how to solve it! I also scanned the neighborhood for wifi jam using InSSIDer, there are few other access points but they don't seem to affect the situation. Any ideas about the steps to follow or tools to use ?

  Read the article

• Alienware m15x (older model) BSOD investigation

  - by Crishu

  A frined of mine asked me to help him with an Alienware m15x laptop that had a little service history. It was bought in june 2008, serviced in january 2009 for a random fps drop problem, Alienware returned it saying nothing was wrong. The laptop still had hiccups, but after juggling a few drivers and settings, the fps drops weren't as noticeable. Eventually it died in Sept. 2009. It would not boot up locking itself on a white/gray screen. (i think it was overheating .. clocking in 100 degrees Celsius). So back to Alienware it went. They replaced the GPU and all was fine. Up until these blue screens started showing up. One other thing that was updated was the HDD and a Windows 7 reinstall, in August. From then on it seems to have started its BSOD. Could this be the culprit? Why? 0_o The original Windows was Vista but it was upgraded with a digital download/purchase of Windows 7 Home Premium and activated after installing windows. No errors on the old HDD, just on the latest installation. LE:Due note that now the old HDD is used to see if issues re-occur. So please, I am in need of someone who can interpret these windows dump files: Minidump I may have come to some conflicting conclusions. So if someone can clarify each dump/date and the probable cause/error it had; and a final conclusion or solution, we would be very grateful. Also please consult report for other system info I omitted: same link,code: XRWIVLWG If I missed something or if you have any other questions I'll be happy to answer them. Thank you. Good day. Processor: Intel(R) Core(TM)2 Duo CPU T9300 @ 2.50GHz Network Adapter Properties: Broadcom NetLink (TM) Gigabit Ethernet Intel(R) Wireless WiFi Link 4965AGN Video Adapter Properties: Driver Description NVIDIA GeForce 8800M GTX Driver Date 19.08.2009 Driver Version 8.16.11.8681 Driver Provider NVIDIA INF File oem19.inf Hardware ID PCI\VEN_10DE&DEV_060C&SUBSYS_0770152D&REV_A2 Location Information @system32\DRIVERS\pci.sys,#65536;PCI bus %1, device %2, function %3;(1,0,0) PCI Device NVIDIA GeForce 8800M GTX [NoDB] BIOS String Version 62.92.34.0.8 Installed Drivers nvd3dum (8.16.11.8681), nvwgf2um, nvwgf2um Hard Dik Drive: Model ID ST9120823ASG (**older one 120gb**) Model ID WD32000BEKT (new 320gb with fresh OS)

  Read the article

• Moving default web site to another drive

  - by Chadworthington

  I set the default location from c:\inetpub\wwwroot to d:\inetpub\wwwroot but when I access my .NET 4.0 site get this error: Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 105: Set explicit="true" to force declaration of all variables. Line 106: --> Line 107: <compilation debug="true" strict="true" explicit="true" targetFramework="4.0"> Line 108: <assemblies> Line 109: <add assembly="System.Web.Extensions.Design, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"/> When I try to Manage the Basic Settings on the Site and click the "Test Settings" button, I see that I have a problem under "authorization:" The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that <domain>\<computer_name>$ has Read access to the physical path. Then test these settings again. 1) Do I need to grant rights to IIS to the new folder? Which user? I thought it was something like IIS_USER or something similar but I cannot determine the correct name of the user. 2) Also, do I need to set the default version of the framework somewhere at the Default Site level or at the Virtual folder level? How is this done in IIS6, I am used to IIS5 or whatever came with XP Pro. 3) My original site had a subfolder under wwwroot called "aspnet_client." How was this cleated? I manually copied it to the corresponding new location. My app was using seperate ASP specific databases for storing session state and role info, if that is relevant. Thanks

  Read the article

• How to store data on a machine whose power gets cut at random

  - by Sevas

  I have a virtual machine (Debian) running on a physical machine host. The virtual machine acts as a buffer for data that it frequently receives over the local network (the period for this data is 0.5s, so a fairly high throughput). Any data received is stored on the virtual machine and repeatedly forwarded to an external server over UDP. Once the external server acknowledges (over UDP) that it has received a data packet, the original data is deleted from the virtual machine and not sent to the external server again. The internet connection that connects the VM and the external server is unreliable, meaning it could be down for days at a time. The physical machine that hosts the VM gets its power cut several times per day at random. There is no way to tell when this is about to happen and it is not possible to add a UPS, a battery, or a similar solution to the system. Originally, the data was stored on a file-based HSQLDB database on the virtual machine. However, the frequent power cuts eventually cause the database script file to become corrupted (not at the file system level, i.e. it is readable, but HSQLDB can't make sense of it), which leads to my question: How should data be stored in an environment where power cuts can and do happen frequently? One option I can think of is using flat files, saving each packet of data as a file on the file system. This way if a file is corrupted due to loss of power, it can be ignored and the rest of the data remains intact. This poses a few issues however, mainly related to the amount of data likely being stored on the virtual machine. At 0.5s between each piece of data, 1,728,000 files will be generated in 10 days. This at least means using a file system with an increased number of inodes to store this data (the current file system setup ran out of inodes at ~250,000 messages and 30% disk space used). Also, it is hard (not impossible) to manage. Are there any other options? Are there database engines that run on Debian that would not get corrupted by power cuts? Also, what file system should be used for this? ext3 is what is used at the moment. The software that runs on the virtual machine is written using Java 6, so hopefully the solution would not be incompatible.

  Read the article

• Why Photoshop CS5's photomerge's result immediately disappear?

  - by koiyu

  I have a bunch of JPG-files which I want to stitch together with Photoshop's Photomerge function. I choose File → Automate → Photomerge... and browse for the files. Photoshop opens the files and starts analyzing. I see the process bar filling and different phases are mentioned on the process bar. Nothing weird there. When the merging is done (and if I don't blink my eyes), I can see layers-palette is populated with the chosen files and, by quickly judging from the layer thumbnails, they're properly aligned. Sometimes the image window itself can be seen, but not always. Problem is that the layers and the image disappear in a flash. There is no error message. Everything is like prior starting the photomerge. No file has been changed. I could continue to use Photoshop normally. This is what I've tried so far: Loaded folder which has 38 JPG images, 4272 x 2848 and ˜ 5 megabytes per file Loaded the same files, but chose Use Files instead of Use Folder in the photomerge's window Loaded 19 JPG images, 4272 x 2848 and ˜ 5 megabytes per file Loaded 10 JPG images, ⇑ see above Loaded 5 JPG images, see above Loaded 3 JPG images, see above Scaled the images to 2256 x 1504 and ˜< 1 megabytes per file Loaded in a set of 38, 19, 10, 5, 3 Following steps are tested with these smaller files and with a set of 5 images Read Adobe's forums and reduced the amount of RAM Photoshop uses gradually from ˜ 80 % to 50 % (though I didn't understand the logic behind this) Would've reduced cache tile size to 128K, but it was set so already Disabled OpenGL Scaled the images to 800 x 533 and ˜ 100 kilobytes per file, loaded a set of 5 Read more unanswered threads around the internet In between each test I closed and reopened Photoshop. This is the first time I've even tried using photomerge. Am I doing something wrong? How can I locate what is the problem? How do I fix this? Photoshop is 64 bit Extended CS5 version. I'm on a mid-2010 quad-core (i5) iMac with up-to-date Mac OS X 10.6.6. Edit: Weird. First loading the images into one file via File → Scripts → Load Files into Stack… and then using Edit → Auto-Align Layers…, which, effectively, is the same as photomerge (even the dialog looks kind of the same), works! Even with the original JPGs without any issues. This doesn't fix photomerge, though.

  Read the article

• Can't find windows 2000 domain after PDC Change

  - by Mark A Kruger

  This is a windows 2000 domain issue. I had an old win2000 PDC that was beginning to fail. So, trying to be pre-emptive, I installed a new BDC, then "demoted" the old PDC and took it off the network. Now it appears that no member server can "find" the domain anymore. No logins work (for services or a RDP or anything). What I've tried (based on googling): Verified sysvol is shared on all servers. Used nslookup to verify that DC's are being found. netdiag /fix meta data cleanup routines. verified no firewall issues (port 389 etc) seizing all roles to new PDC (I did that as part of the original promotion). LMHOST file and Netbios settings. At the moment it seems like I can get the DC's returned but cannot contact them. I'm at a loss. My latest attempt was to remove a member server from the domain and try to "re-add" it. When I do that I get this message: The query was for the SRV record for _ldap._tcp.dc._msdcs.cfwebtools.com The following domain controllers were identified by the query: db-dev1.cfwebtools.com file-prod1.cfwebtools.com cfwt-pdc2.cfwebtools.com However no domain controllers could be contacted. It then goes on to ask if I've checked my A record and made sure they are running. Is there a way to force this domain to be seen? I also shared sysvol (or double checked it) and restarted the dfsr service. More information. I got looking at sysvol and found it was not shared on 2 of these servers. Only one of them (db-dev1) has a "good" or at least "populated" sys vol store. So I tried doing a "d2" recovery of my PDC against that good sysvol. But it never synchs - or at least it does not seem to synch. I'm guessing if I could get sysvol and netlogin to kick in and replicate that would fix my issue. I think these DC's aren't responding because they are waiting for replication which is broken somehow. Would taking down all the DC's except for db-dev1 fix the issue - at least temporarily? I know I can't just copy the sysvol stuff over to the other 2 can I?

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• How to use AD/GPO/Print Services to "push out" a new printer driver to replace a broken one? How did my server get a broken driver?

  - by Zac B

  Context: We have an AD/GPO-managed corporate network with a little over a hundred PCs running Windows 7 x64, and a few managed printers. Our Server2008R2 primary domain controller is configured as a print server for them all. Problem: After a recent windows update and restart (no printer driver updates were included) on the DC, a particular shared printer (Lexmark T650) has begin exhibiting some strange behavior. First, it prints a preceding and following blank page for almost every document, on jobs submitted by about half of client machines (no separator page is configured on the server or any of the clients I've seen). Second, whenever someone tries to access "Printing Preferences" on any client, they recieve the following error message (this happens everywhere, 100% of the time, and didn't happen before the update on the DC): Once they click "OK", the prefs screen appears (with no separator page selected) and everything seems fine. I'm not even sure if these two issues are related, but everyone seems affected by one or both of those issues. What I've Tried: I've been hesitant to un-deploy the problem printer, or remove it via GPO, as it's pretty heavily used. I've tried updating (via MS update and our internal WSUS server) client machines and the DC. No printer driver updates have appeared, and no number of updates or restarts on the server or the client seems to have achieved anything other than my boss getting grumpy that I'm bouncing the domain controller so often. I've tried deleting the drivers on the server, and re-installing them from the original source that has worked for the past year...no change. I've tried selecting "New Driver" for one of the shared printers on a client machine, running as domain admin, and pushed the latest driver found by MSupdate back up to the DC. This changed the version number of the driver recorded in the print server manager, but caused no change--on the client I pushed from, or on any other. The error still appears. Question: Why the heck is this happening? Obviously, I got a bad driver from somewhere, but how do I get rid of it? I don't know of any "roll back drivers" functionality for centrally managed print drivers like Windows offers for other devices. How would I a) get this issue resolved on a client, and b) push the fix to the other members of the domain?

  Read the article

• Exchange IMAP4 connector - Error Event ID 2006

  - by MikeB

  A couple of users in my organisation use IMAP4 to connect to Exchange 2007 (Update rollup 9 applied) because they prefer Thunderbird / Postbox clients. One of the users is generating errors in the Application Log as follows: An exception Microsoft.Exchange.Data.Storage.ConversionFailedException occurred while converting message Imap4Message 1523, user "*******", folder *********, subject: "******", date: "*******" into MIME format. Microsoft.Exchange.Data.Storage.ConversionFailedException: Message content has become corrupted. ---> System.ArgumentException: Value should be a valid content type in the form 'token/token' Parameter name: value at Microsoft.Exchange.Data.Mime.ContentTypeHeader.set_Value(String value) at Microsoft.Exchange.Data.Storage.MimeStreamWriter.WriteHeader(HeaderId type, String data) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeStreamAttachment(StreamAttachmentBase attachment, MimeFlags flags) --- End of inner exception stack trace --- at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeStreamAttachment(StreamAttachmentBase attachment, MimeFlags flags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeAttachment(MimePartInfo part, MimeFlags flags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimePart(MimePartInfo part, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimeParts(List`1 parts, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ItemToMimeConverter.WriteMimePart(MimePartInfo part, MimeFlags mimeFlags) at Microsoft.Exchange.Data.Storage.ImapItemConverter.<>c__DisplayClass2.<WriteMimePart>b__0() at Microsoft.Exchange.Data.Storage.ConvertUtils.CallCts(Trace tracer, String methodName, String exceptionString, CtsCall ctsCall) at Microsoft.Exchange.Data.Storage.ImapItemConverter.WriteMimePart(ItemToMimeConverter converter, MimeStreamWriter writer, OutboundConversionOptions options, MimePartInfo partInfo, MimeFlags conversionFlags) at Microsoft.Exchange.Data.Storage.ImapItemConverter.GetBody(Stream outStream) at Microsoft.Exchange.Data.Storage.ImapItemConverter.GetBody(Stream outStream, UInt32[] indices) From my reading around it seems that the suggestion is to ask users to log in to Outlook / OWA and view the messages there. However, having logged in as the users myself, the messages cannot be found either through searching or by browsing the folder detailed in the log entry. The server returns the following error to the client: "The message could not be retrieved using the IMAP4 protocol. The message has not been deleted and may be accessible using either Microsoft Outlook or Microsoft Office Outlook Web Access. You can also try contacting the original sender of the message to find out about the contents of the message. Retrieval of this message will be retried when the server is updated with a fix that addresses the problem." Messages were transferred in to Exchange by copying them from the old Apple Xserve, accessed using IMAP. So my question, finally: 1. Is there any way to get the IMAP Exchange connector to rebuild its cache of messages since it doesn't seem to be pulling them directly from the MAPI store? 2. Alternatively, if there is no database, any ideas on why these messages don't appear in Outlook or OWA would be gratefully received. Many thanks, Mike

  Read the article

• Why am I unable to send an attachment with Outlook via SMTP that I am able to send via Gmail / Google Apps?

  - by cwd

  I have Google Apps installed and I have tried to set up Outlook 2007 to send messages via SMTP. I followed the guide, selecting what I believe are all the correct settings. Yes, I am using POP for incoming, that is intentional but I don't believe it should affect outgoing messages. When I log into gmail (google apps) for my company, I can send a message that has an 8MB attachment (pdf file, not zipped or anything) and it sends fine. However, when I send the same message in Outlook with that same 8mb attachment it fails. Why am I unable to send an attachment with Outlook via SMTP that I am able to send via Gmail / Google Apps? The message headers are (some info omitted for privacy): Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 552 552 #5.3.4 message size exceeds limit (state 17). ----- Original message ----- DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=company.com; s=google; h=from:to:cc:references:in-reply-to:subject:date:message-id :mime-version:content-type:x-mailer:thread-index:content-language; bh=7d4i/Cbt0v0sY3zt5lN6y5CdvxjbRmTBG4AuBuMxtF4=; b=IJwwxuIEdg1E4zXuGjeDod+1w3RYBBCNzSsqpuX77ih36HSiq++s3ZCQXPeU9CIZVg K8JPJQu9xjivYYjrRaYwyeowLIu0GIdR2h4kKEkFM/GNC2RFF3VwVgj+gvi5eqVZIuWn osT5/VEm10IED6B54NPOtGMgFTci6a57zzVKE= X-Google-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=google.com; s=20120113; h=from:to:cc:references:in-reply-to:subject:date:message-id :mime-version:content-type:x-mailer:thread-index:content-language :x-gm-message-state; bh=7d4i/Cbt0v0sY3zt5lN6y5CdvxjbRmTBG4AuBuMxtF4=; b=LjTecjok5K71Bymp6tZqAL2XCz03hWROV1mTK8Vf2AeEJwtel9ACu9kE5jW5iJqckb upYKPzoqYLBwAPOzMb9asWoTAZPzC7LMG65eDUc2/ZEvGqXrZs3ziUxwhF4t169yRVuy /6nm/aAt5uPMLPdobxGTJ8ahOIku1Z3gW+OcvZ6ERk1Av/bvuln09vcnyJIrHGh7eK8n cbGVxmK0aecgSPgIj2NALbHkyuxwj+LEBRV6uiz3THDjxAiNfsO5UFjV59sD+lVSBT3z ThOGE8WEXRnKHuP3FuKXyeUxKBZ2CxpWJpvDuS9EsFkln7zkISYEsRA0nUA6GSGi2Z/n 8YUg== Received: by 10.60.169.197 with SMTP id ag5mr12254920oec.137.1351036287413; Tue, 23 Oct 2012 16:51:27 -0700 (PDT) References: Date: Tue, 23 Oct 2012 19:51:16 -0400 Message-ID: <003a01cdb179$4bb2ca60$e3185f20$@com> MIME-Version: 1.0 Content-Type: multipart/related; boundary="----=_NextPart_000_003B_01CDB157.C4A12A60" X-Mailer: Microsoft Office Outlook 12.0 Thread-Index: Ac2xVCHGxoC7DDOkQBK3JSXowHb0EQAEB7agAAA/YKAAAIGcQAAAngfQAABAAPAAAFe7gAAAadvw AALgvLA= Content-Language: en-us X-Gm-Message-State: ALoCoQniMq7Fnh+NlfoWjTJPvKWbkhEaftSaFo9ZVvtRpWufTmhlRDx1a9Jf+wmYcbRh896gygNr The company I am sending email to is a company that uses Google Apps for Teams. This is their apps admin login. Should I be worried about that message? My Settings On the Google apps side I have set my SPF record and set / verified my DKIM key. Here are my outlook settings: Why am I unable to send an attachment with Outlook via SMTP that I am able to send via Gmail / Google Apps?

  Read the article

• Undelivered Mail Returned to Sender

  - by Alex

  When sending to [email protected] via PHP mail() function, I receive mails. When sending emails from external machines, I receive the following (e.g., sending from [email protected]. [mail.ru is Russian gmail]): This is the mail system at host fallback2.mail.ru. I'm sorry to have to inform you that your message could not be delivered to one or more recipients. It's attached below. For further assistance, please send mail to <postmaster> If you do so, please include this problem report. You can delete your own text from the attached returned message. The mail system <[email protected]>: lost connection with mail.mydomain.com[xxx.xxx.xxx.xxx] while receiving the initial server greeting Reporting-MTA: dns; fallback2.mail.ru X-mPOP-Fallback_MX-Queue-ID: D8C19F2411F1 X-mPOP-Fallback_MX-Sender: rfc822; [email protected] Arrival-Date: Tue, 29 Oct 2013 10:09:21 +0400 (MSK) Final-Recipient: rfc822; [email protected] Original-Recipient: rfc822;[email protected] Action: failed Status: 4.4.2 Diagnostic-Code: X-mPOP-Fallback_MX; lost connection with mail.tld.com[xxx.xxx.xxx.xxx] while receiving the initial server greeting Here is my postfix main.cf: command_directory = /usr/sbin daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix myhostname = mail.mydomain.com mydomain = mydomain.com myorigin = mydomain.com inet_interfaces = all inet_protocols = all unknown_local_recipient_reject_code = 550 in_flow_delay = 1s alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases mail_name = mydomain.com daemon debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin ddd $daemon_directory/$process_name $process_id & sleep 5 sendmail_path = /usr/sbin/sendmail.postfix newaliases_path = /usr/bin/newaliases.postfix mailq_path = /usr/bin/mailq.postfix setgid_group = postdrop html_directory = no manpage_directory = /usr/share/man sample_directory = /usr/share/doc/postfix-2.6.6/samples readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES bounce_queue_lifetime = 4h maximal_queue_lifetime = 4h delay_warning_time = 1h strict_rfc821_envelopes = yes show_user_unknown_table_name = no allow_percent_hack = no swap_bangpath = no smtpd_delay_reject = yes smtpd_error_sleep_time = 20 smtpd_soft_error_limit = 1 smtpd_hard_error_limit = 3 smtpd_junk_command_limit = 2 mydestination = mydomain.com, localhost.localdomain, localhost smtpd_client_restrictions = permit_inet_interfaces smtpd_recipient_limit = 100 virtual_alias_domains = mydomain.com virtual_alias_maps = hash:/etc/postfix/virtual smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smtpd_sasl_auth_enable = yes smtpd_relay_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination Why emails from external server are not being delivered? Thank you! Update In a log, the following lines appear a lot of times Oct 30 10:48:29 mydomain postfix/smtpd[16216]: connect from fallback5.mail.ru[94.100.176.59] Oct 30 10:48:29 mydomain postfix/smtpd[16216]: warning: SASL: Connect to private/auth failed: Connection refused Oct 30 10:48:29 mydomain postfix/smtpd[16216]: fatal: no SASL authentication mechanisms It appears I have to configure SASL? I would understand if I would like to send emails from postfix, but why do I need it to receive emails?

  Read the article

• Architectural advice - web camera remote access

  - by Alan Hollis

  I'm looking for architectural advice. I have a client who I've built a website for which essentially allows users to view their web cameras remotely. The current flow of data is as follows: User opens page to view web camera image. Javascript script polls url on server ( appended with unique timestamp ) every 1000ms Ftp connection is enabled for the cameras ftp user. Web camera opens ftp connection to server. Web camera begins taking photos. Web camera sends photo to ftp server. On image url request: Server reads latest image on hard drive uploaded via ftp for camera. Server deleted any older images from the server. This is working okay at the moment for a small amount of users/cameras ( about 10 users and around the same amount of cameras), but we're starting to worrying about the scalability of this approach. My original plan was instead of having the files read from the server, the web server would open up an ftp connection to the web server and read the latest images directly from there meaning we should have been able to scale horizontally fairly easily. But ftp connection establishment times were too slow ( mainly due to the fact that PHP out of the ox is unable to persist ftp connections ) and so we abandoned this approach and went straight for reading from the hard drive. The firmware provider for the cameras state they're able to build a http client which instead of using ftp to upload the image could post the image to a web server. This seems plausible enough to me, but I'm looking for some architectural advice. My current thought is a simple Nginx/PHP/Redis stack. Web camera issues post requests of latest image to Nginx/PHP and the latest image for that camera is stored in Redis. The clients can then pull the latest image from Redis which should be extremely quick as the images will always be stored in memory. The data flow would then become: User opens page to view web camera image. Javascript script polls url on server ( appended with unique timestamp ) every 1000ms Camera is sent an http request to start posting images to a provided url Web camera begins taking photos. Web camera sends post requests to server as fast as it can On image url request: Server reads latest image from redis Server tells redis to delete later image My questions are: Are there any greater overheads of transferring images via HTTP instead of FTP? Is there a simple way to calculate how many potential cameras we could have streaming at once? Is there any way to prevent potentially DOS'ing our own servers due to web camera requests? Is Redis a good solution to this problem? Should I abandon PHP/Ngix combination and go for something else? Is this proposed solution actually any good? Will adding HTTPs to the mix cause posting the image to become too slow? Thanks in advance Alan

  Read the article

• Nginx https rewrite turns POST to GET

  - by x7311

  My proxy server runs on ip A and this is how people access my web service. The nginx configuration will redirect to a virtual machine on ip B. For the proxy server on IP A, I have this in my sites-available server { listen 443; ssl on; ssl_certificate nginx.pem; ssl_certificate_key nginx.key; client_max_body_size 200M; server_name localhost 127.0.0.1; server_name_in_redirect off; location / { proxy_pass http://10.10.0.59:80; proxy_redirect http://10.10.0.59:80/ /; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } server { listen 80; rewrite ^(.*) https://$http_host$1 permanent; server_name localhost 127.0.0.1; server_name_in_redirect off; location / { proxy_pass http://10.10.0.59:80; proxy_redirect http://10.10.0.59:80/ /; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } The proxy_redirect was taken from how do I get nginx to forward HTTP POST requests via rewrite? Everything that hits the public IP will hit 443 because of the rewrite. Internally, we are forwarding to 80 on the virtual machine. But when I run a python script such as the one below to test our configuration import requests data = {'username': '....', 'password': '.....'} url = 'http://IP_A/api/service/signup' res = requests.post(url, data=data, verify=False) print res print res.json print res.status_code print res.headers I am getting a 405 Method Not Allowed. In nginx we found that when it hit the internal server, the internal nginx was getting a GET request, even though in the original header we did a POST (this was shown in the Python script). So it seems like rewrite has problem. Any idea how to fix this? When I commented out the rewrite, it hits 80 for sure, and it went through. Since rewrite was able to talk to our internal server, so rewrite itself has no issue. It's just the rewrite dropped POST to GET. Thank you! (This will also be asked on Nginx forum because this is a critical blocker...)

  Read the article

< Previous Page | 326 327 328 329 330 331 332 333 334 335 336 337  | Next Page >