Search Results

Search found 19009 results on 761 pages for 'network shares'.

Page 331/761 | < Previous Page | 327 328 329 330 331 332 333 334 335 336 337 338  | Next Page >

• Getting 0x80070043 error when accessing Samba share from Windows 7

  - by FelixM

  I created a Samba share on my new Ubuntu 10.04 machine. When I try to access it from a Windows 7 client, I get network error 0x80070043 (The network path not found). However, I get this error when I click on the share in the Windows Explorer, so it seems that Windows does find the path. I already enabled NTLMv1, disabled 128bit security and made sure that NetBIOS is running. I briefly disabled the Windows firewall, it didn't make a difference. What could be the problem?

  Read the article

• Packet loss with all adapters on one PC only on the LAN

  - by Enigmativity

  I have a Windows 7 64-bit machine that is losing up to 20% of IP packets on both adapters - wireless & LAN. Browser traffic appears to be affected the most, but it is happening to all protocols. All other computers on the network are functioning fine. If I ping from my faulty machine to any machine on the LAN (wired or wirelessly), including the router/gateway and internet sites, I get up to 20% packet loss. If I do the following commands: ipconfig /release ipconfig /renew then I sometimes get my network performance back for a matter of a few seconds to less than a couple of minutes. Rebooting also works for a short period of time. This problem has been occurring for a couple of months and is getting worse. The computer used to work just fine. I updated the wireless adapter firmware the other day with no effect. Does anyone know what is happening?

  Read the article

• Start tomcat webapp with root privileges

  - by Hagay Myr

  I built a webapp that uses libpcap (via jpcap). In order to be able to get the network interfaces list or to bind to a network interface, the application (in this case a webaap that runs from tomcat server) must be running with root privileges. During development I simply ran Eclipse with root privileges (sudo eclipse) and my webapp worked just fine with Eclipse's local tomcat server. However, when I try to deploy my webapp to the "real" tomcat server, it isn't working. I Also tried to start the tomcat6 service with sudo and changed the TOMCAT6_USER definition (defined in /etc/init.d/tomcat6) from "tomcat6" to "root" but it made no difference. What should I do to make it work?

  Read the article

• netsh wlan add profile not imported passphrase

  - by sirlancelot

  I exported a wireless network connection profile from a Windows 7 machine correctly connected to a WiFi network with a WPA-TKIP passphrase. The exported xml file shows the correct settings and a keyMaterial node which I can only guess is the encrypted passphrase. When I take the xml to another Windows 7 computer and import it using netsh wlan add profile filename="WiFi.xml", it correctly adds the profile's SSID and encryption type, but a balloon pops up saying that I need to enter the passphrase. Is there a way to import the passphrase along with all other settings?

  Read the article

• How do I configure a secondary gateway in RHEL5?

  - by Brett Ryan

  Greetings, we have been experiencing a random timeout issue with VPN users connecting to one of our servers which is causing a problem. My network administrator has instructed me to configure a secondary gateway to include the VPN connection. My current connection resides as follows, 10.1.9.1 is the internal gateway to the internet, I'd like to add 10.1.1.20 as the VPN gateway. # Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet DEVICE=eth0 BOOTPROTO=none BROADCAST=10.1.255.255 IPADDR=10.1.1.22 IPV6_AUTOCONF=yes NETMASK=255.255.0.0 NETWORK=10.1.0.0 ONBOOT=yes GATEWAY=10.1.9.1 TYPE=Ethernet USERCTL=no IPV6INIT=no PEERDNS=yes

  Read the article

• Make puppet agent restart itself

  - by SamKrieg

  I've got a file that notifies the puppet agent. In the network module, the proxy settings are included in the .gemrc file like this: file { "/root/.gemrc": content => "http_proxy: $http_proxy\n", notify => Service['puppet'], } The problem is that puppet stops and does not restart. Aug 31 12:05:13 snch7log01 puppet-agent[1117]: (/Stage[main]/Network/File[/root/.gemrc]/content) content changed '{md5}2b00042f7481c7b056c4b410d28f33cf' to '{md5}60b725f10c9c85c70d97880dfe8191b3' Aug 31 12:05:13 snch7log01 puppet-agent[1117]: Caught TERM; calling stop I assume the code does something like /etc/init.d/puppet stop && /etc/init.d/puppet start Since puppet is not running, it cannot start itself... it kind of makes sense. How to make puppet restart itself when this file changes? Note that this file may not exist as well.

  Read the article

• IIS6 Virtual Directory 500 Error on Remote Share

  - by David Boike

  We have our servers at the server farm in a domain. Let's call it LIVE. Our developer computers live in a completely separate corporate domain, miles and miles away. Let's call it CORP. We have a large central storage unit (unix) that houses images and other media needed by many webservers in the server farm. The IIS application pools run as (let's say) LIVE\MediaUser and use those credentials to connect to a central storage share as a virtual directory, retrieve the images, and serve them as if they were local on each server. The problem is in development. On my development machine. I log in as CORP\MyName. My IIS 6 application pool runs as Network Service. I can't run it as a user from the LIVE domain because my machine isn't (and can not be) joined to that domain. I try to create a virtual directory, point it to the same network directory, click Connect As, uncheck the "Always use the authenticated user's credentials when validating access to the network directory" checkbox so that I can enter the login info, enter the credentails for LIVE\MediaUser, click OK, verify the password, etc. This doesn't work. I get "HTTP Error 500 - Internal server error" from IIS. The IIS log file reports sc-status = 500, sc-substatus = 16, and sc-win32-status = 1326. The documentation says this means "UNC authorization credentials are incorrect" and the Win32 status means "Logon failure: unknown user name or bad password." This would be all and good if it were anywhere close to accurate. I double- and trouble-checked it. Tried multiple known good logins. The IIS manager allows me to view the file tree in its window, it's only the browser that kicks me out. I even tried going to the virtual directory's Directory Security tab, and under Authentication and Access Control, I tried using the same LIVE domain username for the anonymous access credential. No luck. I'm not trying to run any ASP, ASP.NET, or other dynamic anything out of the virtual directory. I just want IIS to be able to load static images, css, and js files. If anyone has some bright ideas I would be most appreciative!

  Read the article

• Web Development Environment: How to distribute edited hosts files over bunch of mac machines?

  - by Alex Reds

  I am doing some research to prepare some web development environment for our small(10ppl and growing) new office. User Case: For each new web project usually we create new alias on an Apache server someproject.companywebsite From my understanding in order to see this website locally for all the rest of our team(including mangers and directors) they will need to edit hosts file (e.g. "192.168.1.10 someproject.companywebsite"), and like that each time for a new project(can be 2-5 each week) Solution: And I looking for a solution how to edit this hosts file only once and distribute it over all mac machines in our network at once or much more flawlessly than poking around with each machine every time over and over again. Is that possible? Or that a very wrong way of doing that? Perhaps we better set up own local dns server and point to it our router? Though own dns server a bit concerns me because of might be some network interruption and others lags, if you know what I mean. Or perhaps there are another workflows for that? What's the best way for such things? So I'll be so grateful to hear some advices from experienced admins. I couldn't find that info on internet, so if you know where to read about it, point me in a right direction. Thank you in advance Alex

  Read the article

• How to cache streaming video and silverlight with squid windows reverse proxy

  - by V. Romanov

  We have an intranet web server running a silverlight application (ACTUS media monitor if anyone cares to know). The server is used to record video and stream it to clients through a CDN solution. We want to put a reverse proxy in between the server and CDN provider in order to remove the office network bottleneck that's currently strangling us. I've set up SQUID for windows on a separate machine outside the network using squid BasicAccelerator configuration setting. It seems to work as far as the reverse proxy is concerned, requests are forwarded and the application is working but it doesn't seem to cache anything (no space is used on the drive where squid is installed). I found to explicit setting to turn caching on in squid, so i assume it's on by default. Perhaps I need some other trick to make the video and/or silverlight cacheable? Any help will be appreciated. Any info you need to help me will be provided at once. Thanks in advance!

  Read the article

• Windows DHCP Server - get notification when a non-AD joined device gets an IP address

  - by TheCleaner

  SCENARIO To simplify this down to it's easiest example: I have a Windows 2008 R2 standard DC with the DHCP server role. It hands out IPs via various IPv4 scopes, no problem there. WHAT I'D LIKE I would like a way to create a notification/eventlog entry/similar whenever a device gets a DHCP address lease and that device IS NOT a domain joined computer in Active Directory. It doesn't matter to me whether it is custom Powershell, etc. Bottom line = I'd like a way to know when non-domain devices are on the network without using 802.1X at the moment. I know this won't account for static IP devices. I do have monitoring software that will scan the network and find devices, but it isn't quite this granular in detail. RESEARCH DONE/OPTIONS CONSIDERED I don't see any such possibilities with the built in logging. Yes, I'm aware of 802.1X and have the ability to implement it long-term at this location but we are some time away from a project like that, and while that would solve network authentication issues, this is still helpful to me outside of 802.1X goals. I've looked around for some script bits, etc. that might prove useful but the things I'm finding lead me to believe that my google-fu is failing me at the moment. I believe the below logic is sound (assuming there isn't some existing solution): Device receives DHCP address Event log entry is recorded (event ID 10 in the DHCP audit log should work (since a new lease is what I'd be most interested in, not renewals): http://technet.microsoft.com/en-us/library/dd759178.aspx) At this point a script of some kind would probably have to take over for the remaining "STEPS" below. Somehow query this DHCP log for these event ID 10's (I would love push, but I'm guessing pull is the only recourse here) Parse the query for the name of the device being assigned the new lease Query AD for the device's name IF not found in AD, send a notification email If anyone has any ideas on how to properly do this, I'd really appreciate it. I'm not looking for a "gimme the codez" but would love to know if there are alternatives to the above list or if I'm not thinking clear and another method exists for gathering this information. If you have code snippets/PS commands you'd like to share to help accomplish this, all the better.

  Read the article

• Internet Working, Browsing Not.

  - by jeffreypriebe

  I have a very odd problem that I can't resolve. I am connected to the internet, but my browsing doesn't work. I don't mean a web browser - I mean browsing. Firefox, Chrome, Curl all fail to successfully connect to an HTTP address. However existing connections, e.g. to mail in Outlook (Exchange Server and also IMAP server) continue to work. Also, the internet is on, I can confirm both from my machine (other ports / connections) as well as from any other computer connected to the same network. Additionally, it appears to be HTTP, not simple a port issue as HTTP over port 8443 (Tortoise SVN if you must know - running over HTTP not over SVN) also fails. I am using Windows Vista SP2 (build 6002). It seems to "creep up" in that after running the computer for a few hours it will fail. (No found way to systematically reproduce the problem.) Additionally, it seems to be more prone on days where the internet connection is flaky already (not sure why the internet is flaky, just is, lot's of failed browsing requests and have to retry/reload often). What I have tried (when the problem arises) - none have yielded any resolution: Resetting the network connection (dis-connect, re-connect) Disable/re-enable the network adapter Double-checked the ip settings Double-checked the HOSTS file. Note: DNS continues to work (both new and cached responses to DNS queries). (Thanks for the suggestion Daniel and antenore.) Checked the routing tables (ip4 only as ipv6 is beyond my understanding) resetting all involved hardware (routers and modems) Close and reopen browsers Looked for malware interference: Run HijackThis Looked for suspicious processes using SysInternals procexp. Looked for explorer hijacks, lsa provider interference, winsock provider interference using SysInternals Autoruns. Run a complete anti-virus scan. Reviewed the output of a netstat -onab to see if there were stuck ports open or unusual processes running somewhere The only thing that works is to do a full reboot. That works 100% of the time to restore browsing. What else can I try to nail down the problem?

  Read the article

• IDC's Sally Hudson on Securing Mobile Access

  - by Naresh Persaud

  After the launch of Identity Management 11g R2, Oracle Magazine writer David Baum sat down with Sally Hudson, research director of security products at International Data Corporation (IDC) to get her perspective on securing mobile access.  Below is an excerpt from the interview. The complete article can be found here. "We’re seeing a much more diverse landscape of devices, computing habits, and access methods from outside of the corporate network. This trend necessitates a total security picture with different layers and end-point controls. It used to be just about keeping people out. Now, you have to let people in. Most organizations are looking toward multifaceted authentication—beyond the password—by using biometrics, soft tokens, and so forth to do this securely. Corporate IT strategies have evolved beyond just identity and access management to encompass a layered security approach that extends from the end point to the data center. It involves multiple technologies and touch points and coordination, with different layers of security from the internals of the database to the edge of the network." ( Sally Hudson, Oracle Mag Sept/Oct 2012) As the landscape changes you can find out how to adapt by reading Oracle's strategy paper on providing identity services at Internet scale. 

  Read the article

• Juniper SRX1400 VPN

  - by ank

  I have been trying to set up a client VPN on a Juniper SRX1400 without much success. All documentation I found from Juniper and elsewhere does a lot of other (difficult and wonderful) things other than the simple things I want to do. We already have a VPN running on CISCO PIX hardware which we need to put to rest and we pretty much like to replicate the functionality, which is: 1) client makes a request to the outside interface of the SRX1400, 2) client gets authenticated, 3) if successful, then client is assigned all the usual DHCP stuff and becomes part of the network. What privileges this DHCP assigned network has, should be configurable of course with the usual routing/filtering methods. Am I asking for too much from the SRX for this kind of thing? Should I ditch the SRX for VPN and revert to an OpenVPN solution that I had working some time back also and was amazed at the ease of configuration, functionality and features?

  Read the article

• pix 501, static route to d-link router (different subnet)

  - by ra170

  I have pix 501 cisco firewall with internal ip 192.168.10.1. I have connected d-link router (dir-655) to pix 501. The d-link router has internal ip 192.168.0.1 The picture would like something like that: |pix 501| has 192.168.10.1 ip |DIR-655| has 192.168.0.1 ip 1. |cable modem|----|pix 501|-------|DIR-655|-----PC 2. PC--------|pix 501|---------|DIR-655| | | |cable modem| When I'm on the wireless network (dir-655) with assigned ip of 192.168.0.x I can cross the subnet and connect to my firewall 192.168.10.1. (pic. 1) The problem is that if I'm on the 192.168.10.x network I can't connect to anything over at 192.168.0.x network. (pic.2) I've tried entering a static route like this: `route inside 192.168.0.0 255.255.255.0 192.168.10.1 1` I also tried assigning static ip to wan interface on DIR-655 to 192.168.10.30 and then tried this: route inside 192.168.0.0 255.255.255.0 192.168.10.30 1 But still, can't connect to 192.168.0.1 or anything on that subnet. Is there a way to setup a static route? Would adding a separate router between PIX 501 and DIR-655 help? I would think that static route like this should take care of it, but it doesn't. This is my route config and nat: (config)# sh route outside 0.0.0.0 0.0.0.0 (outside_IP) 1 DHCP static outside (outside_IP) 255.255.248.0 (outside_IP) 1 CONNECT static inside 192.168.0.0 255.255.255.0 192.168.10.1 1 OTHER static inside 192.168.10.0 255.255.255.0 192.168.10.1 1 CONNECT static or (route inside 192.168.0.0 255.255.255.0 192.168.10.30 1) (config)# sh nat nat (inside) 1 192.168.1.0 255.255.255.0 0 0 nat (inside) 1 192.168.10.0 255.255.255.0 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 I ended up turning DIR-655 into an Access Point (turning off DHCP and pluging cable from PIX lan interface into one of the LAN interfaces on DIR-655, and leaving WAN port empty), that works as far as DIR-655 being on the same subnet now, and I can access every machine. However the question is, why can't I simply route between those two? would router between these two help? One of the reasons is, that the PIX 501 has only 10 licences, so now I'm using almost all of them. (I have few computers, iphones, ps3, print server, etc.) I would really appreciate some help! Thanks.

  Read the article

• Get source and destination of outbound traffic in pfSense

  - by maxsilver

  I'm looking at the traffic graph in pfSense (Version 1.2.2), which we're using as a router / NAT / ect on our network. Recently, I'm seeing a sudden, constant spike of 15 - 30kbps traffic outbound, that is unusual for our network (normally its below 2kbps, we're mostly all inbound traffic) Is there any way to determine what the source of this traffic is, or where it's going? (Just an internal IP address for source, and external IP address for destination would be all I need) I've already tried switching the traffic graph to 'LAN' and watching the host list on the right side, but it seems ... flakey. The numbers it shows seem to fade in and out at random, and the values never add up to anywhere near the graph values. I'm not allowed to post the image, but a photo is available at - http://imgur.com/QYjKI.png

  Read the article

• configuring USB modem( Huawei EC156) in ubuntu 13.10

  - by user205427

  I am facing difficulty in installing my USB modem in Ubuntu 13.10. Contrary to what many have suggested,it does not get detected automatically, nor does setting a new connection help. USB Device is listed in lsusb, but not under network manager or Devices, it is detected as a CD-ROM, what I understood from the web was that usb-modeswitch can be used to switch it to a USB device. Even 'Enable Mobile Broadband' option is not shown in network manager. What was interesting is when I start laptop with windows 7 and use the USB modem and after that restart with Ubuntu, both Enable Broadband and the mobile broadband connection can be seen. Sadly, internet connection could not be installed. I tried using USB-modeswitch command as suggested somewhere, but it does not seem to work. Following is the message. Take all parameters from the command line * usb_modeswitch: handle USB devices with multiple modes * Version 2.0.1 (C) Josua Dietze 2013 * Based on libusb1/libusbx ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1505 HuaweiMode=1 NeedResponse=0 InquireDevice enabled (default) Look for default devices ... found USB ID 8087:0020 found USB ID 1d6b:0002 found USB ID 0461:4db6 found USB ID 12d1:1505 vendor ID matched product ID matched found USB ID 138a:0007 found USB ID 03f0:231d found USB ID 8087:0020 found USB ID 1d6b:0002 Found devices in default mode (1) Access device 005 on bus 001 Get the current device configuration ... OK, got current device configuration (1) Use interface number 0 Use endpoints 0x08 (out) and 0x87 (in) Inquire device details; driver will be detached ... Looking for active driver ... OK, driver detached INQUIRY message failed (error -9) USB description data (for identification) ------------------------- Manufacturer: HUA?WEI TECHNOLOGIES Product: HUAWEI Mobile Serial No.: ??????????????????? ------------------------- Send old Huawei control message ... -> Run lsusb to note any changes. Bye! I am stuck with this problem for 4 days now, any help would be appreciated

  Read the article

• Netboot Intel Macs without BSDP

  - by notpeter

  I have a netboot setup with DeployStudio that works great in my lab, but doesn't work on our main network. After some digging, I believe it's because our network admins are filtering BSDP (Boot Service Discovery Protocol) on our subnet at the switch level. Is it possible to hard code which server my clients (early 2007 iMac Core2Duos) should boot from without relying on BSDP? Perhaps relevant details: I do not have control over switch configs or DHCP settings. Client and server are running 10.6 Snow Leopard. The clients see the netboot server advertising itself in the 'Startup Disk' system preferences pane, but when I go to netboot it just leaves me with a flashing globe.

  Read the article

• keepalived questions (requirements, abilities, limitations)

  - by Poni

  1) What are keepalived's (physical/network) requirements? Does the two (or more) keepalived' nodes need to be connected to the same switch? (something related to broadcasting maybe). 2) Can keepalived nodes run on different networks, "internet" networks? 3) Is keepalived depend on the router? (as far as I understand, the virtual IP should point to the real router/switch that connects both nodes). 4) Is keepalived "service-independent"? - What is keepalived's involvement domain? IPs only? Or is it service/protocol oriented? - Does it deal ONLY with IP, or is it designed for HTTP for example? - In other words, can I use it for custom (network-based) app? 5) Have more than one failover server? If the answer for question #4 is "yes", i.e it depends on the service type, then is there any general alternative? Preferably easy to install/configure :)

  Read the article

• Can I find the session ID for a user logged on to another machine?

  - by Dan Tao

  I want to open an application on another computer on the same network via the command line. The scenario here is that the user is in a room surrounded by about 20 computers and wants to be able to launch the same app on every computer without walking from screen to screen opening it up on each individual machine. I've discovered that I can get the basic functionality for this using PsExec as follows: psexec \\[computer] -u [username] -p [password] -d -i [SessionID] [program] For computer, username, password, and program, I'm good. Does anyone know of a way I can figure out which SessionID is assigned to a particular user logged on to a particular machine on the network? Alternately, is there a better way to go about what I'm trying to accomplish?

  Read the article

• How to set up Windows server 2008 to receive email?

  - by Saul

  First off apologies, I'm from a medical background not a networking one, but I've got roped into setting up a windows 2008 server. So far web server running, fixed IP address assigned (within a large private network of the National Health Service in the UK if that makes any difference) and the network team have assigned a DNS entry for me which works, so the server can be addressed as nww.myserver.nhs.uk I've only got ports open on the router for 80 and 443 (http and https) at the moment, so presume I need a different port to enable email services. My need is to be able to accept an email to the domain name like [email protected] in order to pick up a confirmation mail from an SSL issuer (Comodo) I guess to confirm that I control the domain. After that I don't actually need mail services on the server. I see lots of stuff about setting up SMTP services but thought that was about mail out and re-routing, but how do you get the server to "listen" for mail to the domain (assuming I open port xyz or whatever it is) ?

  Read the article

• Multicast in private LAN with different subnets

  - by Gobliins

  after i read Multicast IP Addresses and Multicast accross the subnets I am confused. Configuration: I have two devices in the same network. They may not be in the same Subnet, but always in the same physical network (beyond the same router, switch etc.) I want to communicate across IP multicast either 224.x.x.x or 239.x.x.x may be more fitting because we want it local, not beyond of forward through the router. Can one machine be the receiver and the other machine sender of the same multicast address? and can the receiving machine send an answer to the sending machine?

  Read the article

• Mac internet problems

  - by Bradley Herman

  Our office is set up with mostly macs (7 of them) but we do have a windows laptop and a windows desktop on the network as well. The network is configured with a modem going into a switch/router throughout the office to the computers, along with a wireless router. Everything runs fine most of the time, but periodically while using the web, certain sites will stop loading and timeout repeatedly. This usually lasts 20 minutes or so and can be incredibly annoying. Resetting the modem/router and/or rebooting the computer never helps. The weirdest part is that in almost every case, the websites are fine on our Windows machines. I frequently use github, google, Stack Overflow, and jQuery reference and I can count on the sites being unavailable to me at least once a day. While I can't get them to load, I can spin my chair around to the windows server behind me and load the sites just fine. Any idea what the hell could be going on here?

  Read the article

• Frequent disconnects with oneiric server using wlan AR9285

  - by John Neil

  I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

  Read the article

• Anyone interested in obtaining a cable list from a visio Diagram? [closed]

  - by Alex

  it's my first post here. Just wondering if anyone had to deal with the following problem - you have to install over say a 100 network elements and servers - cabling is done via contractors, so you need to provide them with an accurate, error-free cable list - your inputs are a set of detailed, port by port, visio diagrams. Prb is to obtain the cable list and get the cabling started while you're busy crafting the switch/routers configs. I coded a Visio plugin, which I plan to release under the GNU license, that returns a cable list from a diagram, and tested it on intermediate size infrastructure, 2K+ cables. It works well. The tool needs a little work to be user friendly, so before getting started, I wanted to know if that was worth the effort. Questions are welcomed, let me know -A PS: the tool is targeted for those who need a port by port description of their network, in the form Source/slot/port/Destination/slot/port.

  Read the article

• OpenVPN bridged not pinging beyond openvpn server on Ubuntu/Windows 2003

  - by ani

  I set up an OpenVPN server using Ubuntu and a windows server 2003 client to interconnect two networks between two different offices. They can now ping each other, but the rest of the network cannot be contacted by the windows client. Office 1 has internal network of: 192.168.0.0 255.255.240.0 Office 2 has internal network of: 192.168.16.0 255.255.255.0 And the configuration files are: Server.conf port 1194 --script-security 2 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" # TCP or UDP server? ;proto tcp proto udp dev tap0 ;dev tun ca ca.crt cert openvpn.crt key openvpn.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.0.59 255.255.240.0 192.168.6.72 192.168.6.75 push "route 192.168.0.0 255.255.240.0" push "dhcp-option DNS 192.168.0.2" push "dhcp-option DOMAIN testeers.local" keepalive 10 120 tls-auth ta.key 0 # This file is secret comp-lzo user nobody group nogroup persist-key persist-tun log /var/log/openvpn/openvpn.log status /var/log/openvpn-status.log verb 3 Client Config file client dev tap ;dev tun --script-security 2 ;proto tcp proto udp remote 1xx.2xx.xxx.124 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert admin-VAIO.crt key admin-VAIO.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 Ifconfig on the server now shows the following: br0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 inet addr:192.168.0.59 Bcast:192.168.15.255 Mask:255.255.240.0 inet6 addr: fe80::250:56ff:fe8b:1a49/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1081860 errors:0 dropped:1358 overruns:0 frame:0 TX packets:242385 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76600615 (76.6 MB) TX bytes:64474575 (64.4 MB) eth0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:1144125 errors:0 dropped:7172 overruns:0 frame:0 TX packets:252486 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:109893729 (109.8 MB) TX bytes:66372620 (66.3 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:67865 errors:0 dropped:0 overruns:0 frame:0 TX packets:67865 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5183276 (5.1 MB) TX bytes:5183276 (5.1 MB) tap0 Link encap:Ethernet HWaddr 32:4f:42:11:b7:c5 inet6 addr: fe80::304f:42ff:fe11:b7c5/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3329 errors:0 dropped:0 overruns:0 frame:0 TX packets:215472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:373205 (373.2 KB) TX bytes:17465832 (17.4 MB)

  Read the article

< Previous Page | 327 328 329 330 331 332 333 334 335 336 337 338  | Next Page >