Search Results

Search found 33162 results on 1327 pages for 'static ip address'.

Page 331/1327 | < Previous Page | 327 328 329 330 331 332 333 334 335 336 337 338  | Next Page >

• Ubuntu 12.04 connected to wireless network but internet not working

  - by A.J.

  I can connect to my house's wireless network just fine, but when I'm connected I can't browse the web. Firefox starts connecting to a site and then just poops out. This doesn't happen on my roommates' computers (running Windows) or on our 3DSes, so I know it's just my laptop. I already tried sudo dhclient -r sudo dhclient sudo ifconfig eth0 down sudo ifconfig eth0 up Results of a few commands I was asked to run in comments: ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. ^C --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (173.194.33.38) 56(84) bytes of data. --- google.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1006ms nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 88:AE:1D:6B:4E:E7 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off - Device: wlan0 [JUSTICE] ----------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: connected Default: yes HW Address: 1C:65:9D:65:C6:31 Capabilities: Speed: 1 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) HOME-9B18: Infra, 00:26:F3:53:9B:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 34 WPA WPA2 cougdad48 Network: Infra, 60:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 22 WPA2 cougdad48 Guest Network: Infra, 66:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA2 belkin.ade: Infra, 94:44:52:FF:8A:DE, Freq 2457 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 *JUSTICE: Infra, 00:24:01:7B:9F:7E, Freq 2462 MHz, Rate 54 Mb/s, Strength 88 WEP CenturyLink: Infra, B2:B2:DC:8E:E2:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 IPv4 Settings: Address: 192.168.0.11 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 (JUSTICE is my home's network.) ping -c 2 198.168.0.1 PING 198.168.0.1 (198.168.0.1) 56(84) bytes of data. --- 198.168.0.1 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms

  Read the article

• KVM Guest not reachable from host

  - by Paul

  Hello, I'm running Ubuntu server 9.10, installed KVM etc. Created the bridge network following instructions on help.ubuntu.com/community/KVM/Networking Created a windows 2008 guest using virt-install command line (using virt-manager GUI from a remote Ubuntu desktop would not let me select the ISO location). I can however use a remote virt-manager to connect to the guest and complete the windows install. Within windows 2008 I changed the IP address but cannot ping from outside world. The bridge network appears fine - I'm not sure what else to look at! Here is the interfaces file: The loopback network interface auto lo iface lo inet loopback The primary network interface auto eth0 iface eth0 inet manual # auto br0 iface br0 inet static address 60.234.64.50 netmask 255.255.255.248 network 60.234.0.0 broadcast 60.234.0.255 gateway 60.234.64.49 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 auto eth1 iface eth1 inet static address 192.168.12.2 netmask 255.255.255.0 broadcast 192.168.12.255 The ip of the windows server is 60.234.64.52 What else should I check? Regards Paul.

  Read the article

• Common Areas For Securing Web Services

  The only way to truly keep a web service secure is to host it on a web server and then turn off the server. In real life no web service is 100% secure but there are methodologies for increasing the security around web services. In order for consumers of a web service they must adhere to the service’s Service-Level Agreement (SLA).  An SLA is a digital contract between a web service and its consumer. This contract defines what methods and protocols must be used to access the web service along with the defined data formats for sending and receiving data through the service. If either part does not abide by the contract then the service will not be accessible for consumption. Common areas for securing web services: Universal Discovery Description Integration  (UDDI) Web Service Description Language  (WSDL) Application Level Network Level “UDDI is a specification for maintaining standardized directories of information about web services, recording their capabilities, location and requirements in a universally recognized format.” (UDDI, 2010) WSDL on the other hand is a standardized format for defining a web service. A WSDL describes the allowable methods for accessing the web service along with what operations it performs. Web services in the Application Level can control access to what data is available by implementing its own security through various methodologies but the most common method is to have a consumer pass in a token along with a system identifier so that they system can validate the users access to any data or actions that they may be requesting. Security restrictions can also be applied to the host web server of the service by restricting access to the site by IP address or login credentials. Furthermore, companies can also block access to a service by using firewall rules and only allowing access to specific services on certain ports coming from specific IP addresses. This last methodology may require consumers to obtain a static IP address and then register it with the web service host so that they will be provide access to the information they wish to obtain. It is important to note that these areas can be secured in any combination based on the security level tolerance dictated by the publisher of the web service. This being said, the bare minimum security implantation must be in the Application Level within the web service itself. Typically I create a security layer within a web services exposed Internet that requires a consumer identifier and a consumer token. This information is then used to authenticate the requesting consumer before the actual request is performed. Refernece:UDDI. (2010). Retrieved 11 13, 2011, from LooselyCoupled.com: http://www.looselycoupled.com/glossary/UDDIService-Level Agreement (SLA). (n.d.). Retrieved 11 13, 2011, from SearchITChannel: http://searchitchannel.techtarget.com/definition/service-level-agreement

  Read the article

• Shibboleth + IIS and Pound Reverse Proxy

  - by boburob

  Having a bit of a problem getting Shibboleth (SSO) working with ADFS and Pound. The main problem seems to be that: The website address will be https://website.domain.com Pound will then terminate the SSL and forward the traffic to the webserver on a different port (http://server.domain.com:8888) I have set up Shibboleth to protect the address http://server.domain.com:8888, which allows me to retrieve metadata and it all seems to be working fine. However the problem seems to be that ADFS is configured to protect the https website, so when Shibboleth attempts to recieve information from ADFS I get nothing except the following error: A token request was received for a relying party identified by the key 'https://msstagrevproxy.cwpintranet.com/shibboleth', but the request could not be fulfilled because the key does not identify any known relying party trust. Key: https://msstagrevproxy.cwpintranet.com/shibboleth I am not really sure how I can work around this as to retrieve the metadata from Shibboleth I have to use the https address but this does not actually exist in Shibboleth or IIS. Has anyone had any experience with this before or using any other SSO with a reverse proxy that works?

  Read the article

• How do I set up hosting a domain name at home with Apache?

  - by Andrew McIntyre

  I am relatively new to Ubuntu Linux and I am struggling to figure out the basic set-up of hosting a domain name at home with Apache2. I understand that you have to change your IP from dynamic to a static IP Address but I am not sure how you achieve that step. I am looking for some assistance on this on how to enable self signing certificates, make the domain name resolve on the Internet from hosting the website on the web server, enabling protected directories and the basic commands of accessing the directory where the website files can be uploaded and available on the World Wide Web.

  Read the article

• Send one invalid email response to sender

  - by Kafuka

  I discovered that my postfix/dovecot configuration isn't rejecting emails. If a person sends an email to an invalid email-address, it just drops it. I am fine with this behavior since I think it discourages spammers from mining emails (I have had some success). Recently a person I did not want to talk to emailed an address I cut off and didn't receive a response back. It would have saved me some problems if they knew to call me instead of sending 50+ emails. How would I configure Dovecot/postfix to send a message back to a sender of an email address and then limit this 1 per domain or unique email. Debian Stable Linux 3.6.5-linode47 Dovecot 1.2.15 Postfix 2.7.1 PSQL - backend if that matters

  Read the article

• Remote Desktop Viewer Set-up for 12.10

  - by Sir Linuxalot

  How do you set up the Remote Desktop in 12.10? I've scanned the available answers here and didn't find anything that answers the question considering the 12.10 interface. Specifically, advice says to check the "Allow Others to Control Your Desktop" and an IP will pop up (10.04 I believe). But when checking this in Quezal no IP shows. So how would I connect to my desktop from somewhere other than the local network, like say a coffee house? I also see this Remmina client program but have no idea if I need to use that as well. Can someone give me a step-by-step or point me to one that I haven't found yet? Thanks.

  Read the article

• Cannot authenticate to SBS 2003

  - by Lerp

  I am trying to connect my machine to my work's entirely windows network and I am having a few issues: Whenever I try to access the server, the authentication dialog just keeps popping back up. I cannot connect to the printers (it says connecting to device failed) I have tried setting up samba, winbind, kerberos, likewise open all to no avail. I have a feeling I am just setting them up wrong. My nautilus shows this when I go to Network Windows Network MASTERMAGNETS I can ping both MASTERMAGNETS.LOCAL and 192.168.0.2 after modifying my /etc/hosts james@jamesmaddison:~$ cat /etc/hosts 127.0.0.1 localhost jamesmaddison 192.168.0.2 MASTERMAGNETS.LOCAL 192.168.0.50 Sharp-Printer # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters I believe that's the correct domain (not sure if that's the correct term) as when I do nslookup MASTERMAGNETS.LOCAL I get the following: james@jamesmaddison:~$ nslookup MASTERMAGNETS.LOCAL Server: 192.168.0.2 Address: 192.168.0.2#53 Name: MASTERMAGNETS.LOCAL Address: 192.168.0.3 Name: MASTERMAGNETS.LOCAL Address: 192.168.0.2 It all worked fine before I reinstalled Ubuntu and now I just cannot get access to the server. All help is appreciated, I need to get this working or I fear I will be forced to develop in a windows environment :(

  Read the article

• Shared to Dedicated or Amazon CloudFront to improve performances and keep secured?

  - by user978548

  I have a Wordpress which currently takes about 1.8s to 2.5s for the home page to completely load in my country. The page weight is about 700Ko (static content included). In order to increase performances, I'm considering two solutions: Switching to a dedicated host. Using amazon s3 cloudfront to serve static contents. My current shared hosting have servers in a neighboring country but not exactly in mine, and both amazon and the dedicated hosting have some, so that's already an advantage. So considering all that, I still have three questions remaining: Currently having a low traffic (100 unique visitors/days, but growing) will it make a huge difference between my shared hosting and a dedicated server ? Knowing that I already use a cookie-less domain to deliver static contents (but using a redirection to the same server), would using amazon s3 make a real difference ? Talking about the cons of dedicated vs amazon s3, if I choose for the dedicated server something like Ubuntu server and do daily package updates and have only port 80 open, would it be sufficient in terms of security (in comparison with my current shared hosting which manage everything for me) ?

  Read the article

• hardware addressing and configurable addressing scheme

  - by Zia ur Rahman

  basically i want to ask question about configurable addressing scheme for LAN interface hardware. i have read about it from a book, some main points are given by a configurable addressing scheme provides a mechanism that a customer can use to set a physical address.The mechanism can be manual (the switches that must be set when the interface is first installed).or an electronic memory such as an EPROM that can be downloded from the computer(what does this means). Most hardware needs to be configured only once- configuration is usually done when the hardware is first installed. Question:Suppose a network administrator configures the LAN interface hardware (assigns the address) when he installs it. Now later on if he needs to change the physical address of the device can he change it? Or in this addressing scheme the hardware can only be configured once and we can not reconfigure it later on.

  Read the article

• Ubuntu 12.04 Server ping gateway responds with destination host unreachable

  - by blckblttkd

  I consider myself fairly avid with Ubuntu and Linux, but this one has me stumped. I built up a Xen Server using Ubuntu 12.04 as the base operating system. It has multiple domUs running on it. My home network has a statically defined network where I got all the network connectivity going peachy. The server was moved to a permanent home this morning. So, the network configuration on the main system had to change. Again, another static network, but now I can't ping the upstream gateway from the host. As the VMs use this NIC over a bridge, they too are broken. Ping responds with "destination host unreachable." I simplified the networking down to a simple static network as seen below (no bridge or anything) just to get it to work. Here's the contents of my /etc/network/interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 216.7.188.228 gateway 216.7.188.225 netmask 255.255.255.240 broadcast 216.7.188.255 network 216.7.188.0 dns-nameservers 8.8.8.8 8.8.4.4 Here's the contents of route -n 0.0.0.0 216.7.188.225 0.0.0.0 UG 100 0 0 eth0 216.7.188.224 0.0.0.0 255.255.255.240 U 0 0 0 eth0 And the results of pinging the gateway: PING 216.7.188.225 (216.7.188.225) 56(84) bytes of data. From 216.7.188.228 icmp_seq=1 Destination Host Unreachable From 216.7.188.228 icmp_seq=1 Destination Host Unreachable From 216.7.188.228 icmp_seq=1 Destination Host Unreachable Again, this worked in one network flawlessly (obviously with different parameters in the interfaces file). I did try using eth1 (as there are two NICS on the server (in case the MAC address got flipped on bootup). No success there. Yes, the cable is in the right port now :) Any thoughts? I appreciate the help!

  Read the article

• Setting Gmail as mail server

  - by Tim S.

  I’m in a slightly weird situation right now, and I don’t have sufficient knowledge to sort this myself without truly understand what I’m doing. Yesterday, I’ve registered a domain (.com) and ordered a VPS, attached to that domain. Chances are I may receive mail on my .com address to confirm the domain. Unfortunately, that domain is nothing, but an empty domain. Currently, there’s no mailserver that fetches my mail. Because I don’t have a mailserver available, I (temporarily) want to use Gmail. I prefer to add it to my existing, personal address, but I’m okay with creating a new account as well. I just want to read possible incoming mails. I’ve tried to set MX records to What do I need to do to get mail to a Gmail address? PS. I’m aware of Google, NSA, etc. PPS. I just want to receive mail. I don’t care if I can’t send via my domain. PPS. Detailed steps would be greatly appreciated, I’m a noob.

  Read the article

• Slow gvfs Samba Performance

  - by Wolfgang

  if I use/acces a Samba Share using Nautilus or manually using "gvfs-mount smb://SERVER-IP/Share" I get a poor Performance, only about 7 mb/s on my 100 Mbit Network. If I access the same Share on Windows I get Fullspeed 100 Mbit (About 11 mb/s), also if I mount using sudo mount -t cifs //SERVER-IP/Share /mountpount which uses cifs instead of gvfs I get fullspeed too, so can anyone tell me if there is a Performance Problem/Bug in gvfs or how gvfs is using SMB Shares differerently ? I tested read Perfomance (From my Network Samba Share) with multiples files and always, the cifs-Version is fullspeed and the GVFS-Version has some mb/s less. After some research I found some tips to optimize the Samba Settings of my Ubuntu Installation and some network tuning tips, but as the CIFS mounted share gets the full Network Speed I don't believe its that kind of problem.

  Read the article

• postfix smtp relay script

  - by Peter Sander

  I have a Postfix server and using it with Outlook (POP/SMTP). I have different sender addresses for an account. Now I want to configure a relay for a specific sender address. For example I have postfix for my main domain domain1.com. Now I have a sender address that is domain2.com. For that sender address I want that postfix to relay mail to a second SMTP server. I think that should be possible without problems. But the problem is that I have to create a SSH tunnel to the second server to connect to the SMTP server. But I cant use a persistent SSH connection so I want to know if it is possible that postfix executes some script before relaying the mail to the second SMTP server. I already found some information for executing a script when incomming emails but I only want to establish the SSH tunnel before postfix relays the mail to the second SMTP server.

  Read the article

• VMWare Fusion cannot connect to the NAT connection on my Mac

  - by FFish

  I have been using VMWare Fusion on my Mac to check out my websites on localhost. Now I can't connect anymore with the NAT connection. There seems to be a problem with my IP address or Mac address? I have no idea what causes this, it was working fine before!? In the XP (SP2) VM, in the taskbar I see the Local Area Connection with the yellow warning icon. The bubble says: "This connection has limited or no connectivity. You might not be aisle to access the Internet or some network resources. For more information, click this message." Doing that opens up the Local Area Connection Status panel. In the Support tab, when I click the repair button I get following message: "Windows could not finish repairing the problem because the following action cannot be completed: Renewing IP address." Any help would be greatly appreciated.

  Read the article

• Pattern for a class that does only one thing

  - by Heinzi

  Let's say I have a procedure that does stuff: void doStuff(initalParams) { ... } Now I discover that "doing stuff" is quite a compex operation. The procedure becomes large, I split it up into multiple smaller procedures and soon I realize that having some kind of state would be useful while doing stuff, so that I need to pass less parameters between the small procedures. So, I factor it out into its own class: class StuffDoer { private someInternalState; public Start(initalParams) { ... } // some private helper procedures here ... } And then I call it like this: new StuffDoer().Start(initialParams); or like this: new StuffDoer(initialParams).Start(); And this is what feels wrong. When using the .NET or Java API, I always never call new SomeApiClass().Start(...);, which makes me suspect that I'm doing it wrong. Sure, I could make StuffDoer's constructor private and add a static helper method: public static DoStuff(initalParams) { new StuffDoer().Start(initialParams); } But then I'd have a class whose external interface consists of only one static method, which also feels weird. Hence my question: Is there a well-established pattern for this type of classes that have only one entry point and have no "externally recognizable" state, i.e., instance state is only required during execution of that one entry point?

  Read the article

• What is a good way to share internal helpers?

  - by toplel32

  All my projects share the same base library that I have build up over quite some time. It contains utilities and static helper classes to assist them where .NET doesn't exactly offer what I want. Originally all the helpers were written mainly to serve an internal purpose and it has to stay that way, but sometimes they prove very useful to other assemblies. Now making them public in a reliable way is more complicated than most would think, for example all methods that assume nullable types must now contain argument checking while not charging internal utilities with the price of doing so. The price might be negligible, but it is far from right. While refactoring, I have revised this case multiple times and I've come up with the following solutions so far: Have an internal and public class for each helper The internal class contains the actual code while the public class serves as an access point which does argument checking. Cons: The internal class requires a prefix to avoid ambiguity (the best presentation should be reserved for public types) It isn't possible to discriminate methods that don't need argument checking   Have one class that contains both internal and public members (as conventionally implemented in .NET framework). At first, this might sound like the best possible solution, but it has the same first unpleasant con as solution 1. Cons: Internal methods require a prefix to avoid ambiguity   Have an internal class which is implemented by the public class that overrides any members that require argument checking. Cons: Is non-static, atleast one instantiation is required. This doesn't really fit into the helper class idea, since it generally consists of independent fragments of code, it should not require instantiation. Non-static methods are also slower by a negligible degree, which doesn't really justify this option either. There is one general and unavoidable consequence, alot of maintenance is necessary because every internal member will require a public counterpart. A note on solution 1: The first consequence can be avoided by putting both classes in different namespaces, for example you can have the real helper in the root namespace and the public helper in a namespace called "Helpers".

  Read the article

• My computer stops seeing the other computers on my network

  - by dan

  I'm running Ubuntu 11.04. Sometimes my computer stops seeing the names of the other computers on my network. So I can no longer log into another computer by typing the hosting name e.g. ssh [email protected] I can still log in using the local network IP address. How can I get the first way to work again without rebooting? I know this problem is local to the computer. The other computers on my network can still see one another. But they can no longer see the computer I'm working on, not even by local ip address.

  Read the article

• Having Trouble Granting Access Via Squid

  - by Muhnamana

  I'm by far no expert at this but how do I grant access to Squid? I'm current using 2.7.STABLE9. I've read you need to add a couple of lines, an acl and http_access line. So here's what I added and where. I highly doubt this is right since I'm trying to connect via my laptop and Firefox is yelling at me saying the proxy server is refusing connections. ACL Part: # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed **acl all_computers scr 192.168.1.0/255.255.255.0** acl localnet src 10.0.0.0/8 # RFC1918 possible internal network acl localnet src 172.16.0.0/12 # RFC1918 possible internal network acl localnet src 192.168.0.0/16 # RFC1918 possible internal network http_access part: # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed #http_access allow localnet http_access allow localhost http_access allow all_computers Any suggestions on what I'm doing wrong?

  Read the article

• Why do I get "General Failure" when pinging host name on a Win 7 node on the network?

  - by hydroparadise

  This is a very peculiar problem with a station on our network. The client pc is running Windows 7 Pro. What makes this problem interesting is that this client is the only node on the network that seems to be experiencing this proglem. When I try to ping a specific Win 08 server by host name, I get an IPv6 address and get General failure. But when I ping it's IPv4 address, it responds just fine. My first thought would check the DNS server the name resolutions to see what would be going on, but the problem begs the quesion, why does the station get an IPv6 address back and fails as opposed to using the IPv4 settings (which are static btw). What gives? I am including a screen shot of trying the one specific server and failing while trying another server with success. All other nodes on the network don't have problems communicating with the server the one station is having issues with.

  Read the article

• reverse nslookup fails for single machine

  - by matt wilkie

  I have a computer on a windows Active Directory network for which reverse dns lookup fails. It doesn't matter which machine runs the lookup. The problem computer is a debian vm on a windows server 2003 host. >nslookup wiki.dept Server: primary.internal.domain.org Address: 192.111.222.44 Name: wiki.dept.internal.domain.org Address: 192.111.111.185 >nslookup 192.111.111.185 Server: primary.internal.domain.org Address: 192.111.222.44 *** primary.internal.domain.org can't find 192.111.111.185: Non-existent domain Contents of /etc/resolv.conf on the debian guest: nameserver 192.111.111.244 nameserver 192.111.222.44 search internal.domain.org What is wrong? how do I get ip-to-name resolution to work for this machine? Thank you.

  Read the article

• Using PreApplicationStartMethod for ASP.NET 4.0 Application to Initialize assemblies

  - by ChrisD

  Sometimes your ASP.NET application needs to hook up some code before even the Application is started. Assemblies supports a custom attribute called PreApplicationStartMethod which can be applied to any assembly that should be loaded to your ASP.NET application, and the ASP.NET engine will call the method you specify within it before actually running any of code defined in the application. Lets discuss how to use it using Steps : 1. Add an assembly to an application and add this custom attribute to the AssemblyInfo.cs. Remember, the method you speicify for initialize should be public static void method without any argument. Lets define a method Initialize. You need to write : [assembly:PreApplicationStartMethod(typeof(MyInitializer.InitializeType), "InitializeApp")] 2. After you define this to an assembly you need to add some code inside InitializeType.InitializeApp method within the assembly. public static class InitializeType {     public static void InitializeApp()     {           // Initialize application     } } 3. You must reference this class library so that when the application starts and ASP.NET starts loading the dependent assemblies, it will call the method InitializeApp automatically. Warning Even though you can use this attribute easily, you should be aware that you can define these kind of method in all of your assemblies that you reference, but there is no guarantee in what order each of the method to be called. Hence it is recommended to define this method to be isolated and without side effect of other dependent assemblies. The method InitializeApp will be called way before the Application_start event or even before the App_code is compiled. This attribute is mainly used to write code for registering assemblies or build providers. Read Documentation I hope this post would come helpful.

  Read the article

• Graph data structures and journal format for mini-IDE

  - by matec

  Background: I am writing a small/partial IDE. Code is internally converted/parsed into a graph data structure (for fast navigation, syntax-check etc). Functionality to undo/redo (also between sessions) and restoring from crash is implemented by writing to and reading from journal. The journal records modifications to the graph (not to the source). Question: I am hoping for advice on a decision on data-structures and journal format. For the graph I see two possible versions: g-a Graph edges are implemented in the way that one node stores references to other nodes via memory address g-b Every node has an ID. There is an ID-to-memory-address map. Graph uses IDs (instead of addresses) to connect nodes. Moving along an edge from one node to another each time requires lookup in ID-to-address map. And also for the journal: j-a There is a current node (like current working directory in a shell + file-system setting). The journal contains entries like "create new node and connect to current", "connect first child of current node" (relative IDs) j-b Journal uses absolute IDs, e.g. "delete edge 7 - 5", "delete node 5" I could e.g. combine g-a with j-a or combine g-b with j-b. In principle also g-b and j-a should be possible. [My first/original attempt was g-a and a version of j-b that uses addresses, but that turned out to cause severe restrictions: nodes cannot change their addresses (or journal would have to keep track of it), and using journal between two sessions is a mess (or even impossible)] I wonder if variant a or variant b or a combination would be a good idea, what advantages and disadvantages they would have and especially if some variant might be causing troubles later.

  Read the article

• Nested entities in Google App Engine. Do I do it right?

  - by Aleksandr Makov

  Trying to make most of the GAE Datastore entities concept, but some doubts drill my head. Say I have the model: class User(ndb.Model): email = ndb.StringProperty(indexed=True) password = ndb.StringProperty(indexed=False) first_name = ndb.StringProperty(indexed=False) last_name = ndb.StringProperty(indexed=False) created_at = ndb.DateTimeProperty(auto_now_add=True) @classmethod def key(cls, email): return ndb.Key(User, email) @classmethod def Add(cls, email, password, first_name, last_name): user = User(parent=cls.key(email), email=email, password=password, first_name=first_name, last_name=last_name) user.put() UserLogin.Record(email) class UserLogin(ndb.Model): time = ndb.DateTimeProperty(auto_now_add=True) @classmethod def Record(cls, user_email): login = UserLogin(parent=User.key(user_email)) login.put() And I need to keep track of times of successful login operations. Each time user logs in, an UserLogin.Record() method will be executed. Now the question — do I make it right? Thanks. EDIT 2 Ok, used the typed arguments, but then it raised this: Expected Key instance, got User(key=Key('User', 5418393301680128), created_at=datetime.datetime(2013, 6, 27, 10, 12, 25, 479928), email=u'[email protected]', first_name=u'First', last_name=u'Last', password=u'password'). It's clear to understand, but I don't get why the docs are misleading? They implicitly propose to use: # Set Employee as Address entity's parent directly... address = Address(parent=employee) But Model expects key. And what's worse the parent=user.key() swears that key() isn't callable. And I found out the user.key works. EDIT 1 After reading the example form the docs and trying to replicate it — I got type error: TypeError('Model constructor takes no positional arguments.'). This is the exacto code used: user = User('[email protected]', 'password', 'First', 'Last') user.put() stamp = UserLogin(parent=user) stamp.put() I understand that Model was given the wrong argument, BUT why it's in the docs?

  Read the article

• Iptables Issue can't SSH Remote Machines

  - by Lonston

  I want to SSH to 192.168.1.15 Server from my machine, my ip was 192.168.1.99 Source Destination was UP, with IP 192.168.1.15. This is LAN Network there are 30 Machine's Connected to the network and working fine, I'm Playing around the local machine's cos i need to apply the same rules in Production VPS I have applied the below iptables in my machine 192.168.1.99, Now i can't receive any packets from Outside and i can't send any packets Outside, While applying the Below Chain iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP After the above CHAIN i have added the Below rules and it want to allow ssh from machine to 192.168.1.15 to access the 192.164.1.15 but still i can't access 192.168.1.15 iptables -A INPUT -p tcp -i eth0 --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -o eth0 --sport 22 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT Any one Please Check Weather my Rules are Wrigt. Still i can't access the machine 15

  Read the article

< Previous Page | 327 328 329 330 331 332 333 334 335 336 337 338  | Next Page >